Search Results

Search found 19055 results on 763 pages for 'high performance'.

Page 621/763 | < Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >

• LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

  - by Michael Pearson

  We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

  Read the article

• Fetch videos from sony handycam to linux

  - by bstpierre

  I've got a Sony Handycam DCR-DVD101. When I plug connect the USB cable to my laptop (Ubuntu 10) it doesn't mount any storage device. If I run usb-devices, I see: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=00c1 Rev=01.00 S: Manufacturer=SONY S: Product=Storage Device C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage The driver says usb-storage, but I'm not sure how to get the device mounted. Is there a way to make this work? Update: checking dmesg, I see: [259072.576559] usb 2-1.1: new high speed USB device using ehci_hcd and address 6 [259072.687200] usb 2-1.1: configuration #1 chosen from 1 choice [259072.836188] Initializing USB Mass Storage driver... [259072.836476] scsi5 : SCSI emulation for USB Mass Storage devices [259072.836632] usb-storage: device found at 6 [259072.836636] usb-storage: waiting for device to settle before scanning [259072.836660] usbcore: registered new interface driver usb-storage [259072.836666] USB Mass Storage support registered. [259077.830410] usb-storage: device scan complete [259077.832343] scsi 5:0:0:0: CD-ROM SONY DDX-A1010 R1.0 PQ: 0 ANSI: 0 [259077.888167] sr1: scsi3-mmc drive: 0x/0x pop-up [259077.888446] sr 5:0:0:0: Attached scsi CD-ROM sr1 [259077.888593] sr 5:0:0:0: Attached scsi generic sg2 type 5 [259080.002079] sr 5:0:0:0: [sr1] Unhandled sense code [259080.002085] sr 5:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [259080.002091] sr 5:0:0:0: [sr1] Sense Key : Blank Check [current] [259080.002097] sr 5:0:0:0: [sr1] Add. Sense: No additional sense information [259080.002104] sr 5:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 00 00 [259080.002117] end_request: I/O error, dev sr1, sector 0 [259080.002123] Buffer I/O error on device sr1, logical block 0 [259080.002128] Buffer I/O error on device sr1, logical block 1 Those I/O errors don't look good, is there any hope?

  Read the article

• Least CPU intensive way of streaming your screen on windows?

  - by sinni800

  Hello, sometimes I like capturing my screen for others to see. Only thing: I am playing games while I do it. I have tried a few streaming solutions where Windows Media Encoder coupled with my own Windows server appealed to me most, because I can change resolutions, etc. I also tried ustream coupled with the Flash applet and the Adobe Flash Encoder recording a Camtasia source. Camtasia has the disadvantage though that it shows the green-and-black-alternating borders and can not be targeted fullscreen. I like how xfire does it. But it doesn't work with every game, many are simply not supported. A few thoughts about this: Is there a program which captures like Fraps or XFire (based on Direct3D and OpenGL outputs) and exposes the output to a DirectShow source filter? Which brings me to: Is there hardware accelerated capturing directly from the graphics card? Maybe including direct encoding with help from OpenCL? Modern graphic cards decode BluRay content directly for example. I should have a modern enough graphics processor for this to be possible (see below). If using Windows Media Encoder: Which are the least CPU intensive settings? Which codec? Is there a newer codec than Windows Media 9? Is it less CPU intensive? I only have 7, 8 and 9 inside the Encoder Could the performance be massively increased by having a Quad-Core CPU (see below)? Bandwidth is no problem up to 1000 to 1500 kbit/s (I have 2048). My Computer specs: Intel Core 2 Duo E8400 4 GB DDR2-800 Ram Ati Radeon HD5770 Using Windows 7 Professional

  Read the article

• How to let MSN or Yahoo Messenger set you to be Invisible or Offline when you are idle for an hour?

  - by Jian Lin

  The short question is: How do we let MSN or Yahoo Messenger set us to be Invisible or Offline when we are idle for half an hour or an hour? The reason is: if I am on 24 hours a day, some people see me as weird. Some people see my value as low, because I am always there. There are ways to set me to "Away" or "Busy" after 10 minutes, but there seems to be no way to set myself to invisible or offline after 1 hour. As I am a software developer, I am very used to turning the computer on 24 hours a day. (for example, for checking email for urgent fixes, and fix issue and push to web server). We don't turn off computer usually even when we sleep, because we may sometimes can't sleep yet and come check on the computer, or wake up in the morning and immediately need to check if everything is ok. But, my MSN and Yahoo Messenger is always on for 24 hours a day, and I found that some girls start to ask me why I am always there 24 hours a day (even though they see me as away or busy, their feeling is that I am always there). What's more, I found that since I am always there, my value actually drop in their eyes, because hard to get = high value, and always there = low value. Some people feel me as having nothing much to do, always in front of computer, or what is he doing in front of computer so much? Now since it is my job, and I need to read emails once in a while, I am in fact in front of the computer more than some other people. I am in front of the computer maybe 10 hours a day, far from 24 hours a day. Is there an easy and automatic solution to this?

  Read the article

• Windows typeperf and pound signs.

  - by Weegee

  I'm currently trying to use typeperf to access some Windows performance counters. Unfortunately, a few of the instances I'm trying to check are of the format service#1. The command typeperf "\\server\Process(service#1)\Working Set Peak" is unfortunately returning the data for \\server\Process(service)\Working Set Peak rather than the data for the instance service#1. This holds true for any of the services that have pound signs in the counter string. Does anyone know of a method to get around this problem? Sample output: I:\>typeperf -s server "\Process(service#1)\Working Set" "(PDH-CSV 4.0)","\\server\Process(service)\Working Set" "10/08/2009 09:37:29.070","1643274240.000000" "10/08/2009 09:37:30.070","1643274240.000000" "10/08/2009 09:37:31.070","1643274240.000000" The command completed successfully. I:\>typeperf -s server "\Process(service#2)\Working Set" "(PDH-CSV 4.0)","\\server\Process(service)\Working Set" "10/08/2009 09:37:39.273","1643274240.000000" "10/08/2009 09:37:40.273","1643274240.000000" "10/08/2009 09:37:41.273","1643274240.000000" "10/08/2009 09:37:42.273","1643274240.000000" "10/08/2009 09:37:43.273","1643274240.000000" The command completed successfully. I can confirm in PerfMon that the Working Set value "1643274240.000000" is incorrect for both service#1 and service#2. I am running Windows XP Service Pack 2, but a co-worker who is running Windows Server 2003 was having the same troubles.

  Read the article

• KVM network bridge with two NICs

  - by Eil

  Greetings, I'm trying to set up bridged networking with KVM and am getting nowhere. There are docs and tutorials on the subject, but they all seem to conflict or don't provide enough info. I was wondering if someone can give me a high-level overview of how to get this working. I can probably work out the details myself (configuring the interfaces, adding routes, etc), I just need help on the big picture: how everything is interconnected. I have a RHEL5 server with KVM installed and running. It has two physical NICs, eth0 and eth1 in the same VLAN. I would like to use eth1 for all traffic between the guests and the rest of the network and reserve eth0 for host management, guest migrations, etc if possible. I'm not picky about which one gets the default route, although it would be nice if we could make it eth0. All of the guests will have static IPs. I would prefer that when a new guest is added, the networking configuration only needs to be set from within the guest itself. Basically, I want this: eth0: all host traffic eth1: all guest traffic Open to any other suggestions if this isn't possible or will be kludgy/difficult. Pointers to existing documentation might not be helpful since I've already been though just about everything out there. Thanks for any help.

  Read the article

• SpamAssassin bayesian score discrepancies

  - by CaptSaltyJack

  This makes my brain hurt. For some reason, SpamAssassin is giving high scores to certain emails, but when I test them on the command line, they get a low score. This one particular email has this in the header: X-Spam-Flag: YES X-Spam-Score: 8.521 X-Spam-Level: ******** X-Spam-Status: Yes, score=8.521 tagged_above=-9999 required=5 tests=[BAYES_99=3.5, BAYES_999=0.2, HTML_MESSAGE=0.001, NO_RECEIVED=-0.001, NO_RELAYS=-0.001, RAZOR2_CF_RANGE_51_100=0.5, RAZOR2_CF_RANGE_E8_51_100=1.886, RAZOR2_CHECK=0.922, URIBL_RHS_DOB=1.514] autolearn=no Yet when I dump the raw email into a file msg and run sudo su amavis -c 'spamassassin -t msg', I get this output: Content analysis details: (3.8 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- 1.5 URIBL_RHS_DOB Contains an URI of a new domain (Day Old Bread) [URIs: cliobeads.com] -1.0 ALL_TRUSTED Passed through trusted hosts only via SMTP 0.0 HTML_MESSAGE BODY: HTML included in message -0.0 BAYES_20 BODY: Bayes spam probability is 5 to 20% [score: 0.1855] 1.9 RAZOR2_CF_RANGE_E8_51_100 Razor2 gives engine 8 confidence level above 50% [cf: 100] 0.5 RAZOR2_CF_RANGE_51_100 Razor2 gives confidence level above 50% [cf: 100] 0.9 RAZOR2_CHECK Listed in Razor2 (http://razor.sf.net/) I'm really confused as to why when the email comes in, it gets a completely different score attached to it than when I run spamassassin -t. Is there some other way I should be testing emails? Also, my users have the ability to drag false positives into a folder called "False Positives," and every day a cron job fires off that runs this on every message in every user's folder: sa-learn --dbpath=/var/lib/amavis/.spamassassin --ham /tmp/*-*.eml >/dev/null I ran sudo locate bayes_toks and there's definitely only one bayes DB on the system, in /var/lib/amavis/.spamassassin. I'm clueless, any help would be great and may help restore my sanity!

  Read the article

• Redundant OpenVPN connections with advanced Linux routing over an unreliable network

  - by konrad

  I am currently living in a country that blocks many websites and has unreliable network connections to the outside world. I have two OpenVPN endpoints (say: vpn1 and vpn2) on Linux servers that I use to circumvent the firewall. I have full access to these servers. This works quite well, except for the high package loss on my VPN connections. This packet loss varies between 1% and 30% depending on time and seems to have a low correlation, most of the time it seems random. I am thinking about setting up a home router (also on Linux) that maintains OpenVPN connections to both endpoints and sends all packets twice, to both endpoints. vpn2 would send all packets from home to vpn1. Return trafic would be send both directly from vpn1 to home, and also through vpn2. +------------+ | home | +------------+ | | | OpenVPN | | links | | | ~~~~~~~~~~~~~~~~~~ unreliable connection | | +----------+ +----------+ | vpn1 |---| vpn2 | +----------+ +----------+ | +------------+ | HTTP proxy | +------------+ | (internet) For clarity: all packets between home and the HTTP proxy will be duplicated and sent over different paths, to increase the chances one of them will arrive. If both arrive, the first second one can be silently discarded. Bandwidth usage is not an issue, both on the home side and endpoint side. vpn1 and vpn2 are close to each other (3ms ping) and have a reliable connection. Any pointers on how this could be achieved using the advanced routing policies available in Linux?

  Read the article

• Updated XAMPP with MySQL, all my tables are missing

  - by user371699

  I just updated XAMPP to a newer version, which included updating MySQL from 5.5 to 5.6. Using phpMyAdmin, however, all of my tables within my databases still appear on the left navigation panel, but the main window shows that all my databases are empty (except for information_schema, and a couple other default tables.) Clicking on a table in the navigation panel gives me a "table doesn't exist" message. It does looks like information_schema.tables doesn't have my tables, either. Can anyone assist me with this? I did make a complete backup of all my databases before the upgrade, but I first want to see if I can fix this the "normal" way. Furthermore, I'm not sure if the MySQL upgrade involved making changes to the information/performance databases, so I don't know if I can restore the old ones. Thank you. EDIT: Continuing my searching, I realized that only the INNODB databases are missing. I've tried running the following with no avail: /opt/lampp/bin $ sudo ./mysql_install_db --basedir=/opt/lampp and /opt/lampp/bin $ sudo ./mysql_install_db --basedir=/opt/lampp --datadir=/opt/lampp/var/mysql The my.cnf file in /opt/lampp/etc contains the following InnoDB settings: innodb_data_home_dir = /opt/lampp/var/mysql/ innodb_data_file_path = ibdata1:10M:autoextend innodb_log_group_home_dir = /opt/lampp/var/mysql/ # You can set .._buffer_pool_size up to 50 - 80 % # of RAM but beware of setting memory usage too high innodb_buffer_pool_size = 16M # Deprecated in 5.6 #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size innodb_log_file_size = 5M innodb_log_buffer_size = 8M innodb_flush_log_at_trx_commit = 1 innodb_lock_wait_timeout = 50 What could possibly be wrong? Why is the information_schema not updating correctly? It looks like /opt/lampp/var/mysql has all my tables in it within the database directories, but they're still not showing up in information_schema.

  Read the article

• Body of email breaks distribution list in exchange?

  - by widgisoft

  Hi, I have a very odd problem that I'm not sure is a programming issue or a server issue :-p. Basically I'm sending an email to an exchange distribution list that includes a PHP stack trace; during certain faults the trace includes really high level information such as the machine's environment variables (during file reads, etc.). I went through a copy of the email line by line until the email sent and it appears the line: [SUDO_COMMAND] => /etc/init.d/httpd restart is the culprit. Adding a string replacement in before the email is sent allows a successful send. What I don't understand is WHY these stream of characters are causing the issue ONLY on the distribution email. If I send the email to myself as well, i.e. "[email protected]; [email protected]", then I get the email fine. Re-ordering the list doesn't make a difference the group never gets the email. Because the individual gets the email and not the group I'm assuming the fault is with exchange and some rogue filtering - I've gone through it with the sysadmins and there's no filtering of any sort on that group... so maybe it's a bug? I can't find anyone else having recorded this specific fault so I figured I'd open it here. For now I'm just not using the distribution list but it'd be nice to eventually find the solution. Many thanks, Chris

  Read the article

• I need help choosing between two configurations of the Dell Studio 14

  - by Adnan

  There are two configurations of the Dell Studio 14 (1458) which I'm looking at: Config 1: Core i7-720QM @ 1.6 GHz; ATI Mobility Radeon HD 5450 1GB; 4gb DDR3 RAM @ 1066 MHz; 500 GB SATA HDD @ 7200 RPM; Price: $999 Config 2: Core i5-430M; ATI Mobility Radeon HD 4530 512MB; 4GB DDR3 RAM @ 1066 MHz; 500 GV SATA HDD @ 7200 RPM; Price: $874 What I want to know is, would config 1 still be able to do decent gaming (maybe some Starcraft II), and is there a great performance difference between the i5 and i7 processors? Is the $130 extra worth it for the i7 and better graphics card? I do more than just basic computing. I plan on getting into web design (specifically using Photoshop and Dreamweaver), and I wish to do gaming. I know Conifg 1 is the better value, but I want to be sure that the $130 more is truly worth it. I dont have too much money and want to spend wisely as possible, yet I am a computer geek and plan on doing a lot more than the average user.

  Read the article

• 32 core (each physical core) 2.2 GhZ or 12 core (6 physical cores) 3.0GHZ?

  - by Tejaswi Rana

  I am working on a multithreaded application (Forex trading app built on C#) and had the client upgrade from the 12 core 3.0GHZ machine (Intel) to a 32 core 2.2 Ghz machine (AMD). The PassMark benchmark results were significantly higher when using multicores doing Integer, Floating and other calculations while for a single core calculation it was a bit slower than the pack (others that were being compared to with similar config as the 12 core one). Oh it also comes with 64 GB RAM (4 times as the other one) and a much faster SSD. So after configuring and running the application on that machine, not only did it not perform as well, it was significantly slower. We're talking about 30seconds - 1 minute slower on an app that usually completes processing within 5-20 secs. The application uses MAX DEGREE of PARALLELISM (TPL) which I've tried setting to number of cores and also half of that. I've also tried running single threaded and without setting any limits in parallel threading. While it may be the hardware has some issues, I am wondering if the CPU processing speed is the issue. I can overclock to 3.0 GHZ. But is that even a good idea? Server Info - AMD http://www.passmark.com/forum/showthread.php?4013-AMD-Dual-6272-performance-is-60-lower-than-benchmarks Seems that benchmark was wrong to start with - officially. Intel i7 3930k OS (same in both) Windows 7 Professional 64-bit

  Read the article

• How can I regain control over a "stuck" scroll bar?

  - by jonsca

  I normally have a lot of tabs open in the browser at one time, which normally doesn't cause any problems. Occasionally, though, the page will have fully rendered, the scroll bar is at the top of its track on the right, but placing the the mouse pointer on the scroll bar does not allow me to get control of it (and using the arrow at the bottom of the scroll bar doesn't work either). This seems to happen to me in both Firefox and Chrome, both latest versions. There is normally no load on the CPU, and while my memory usage can be high (especially with Chrome), I still usually have 25% left. I fear that this is one of those "for your own good" features, to prevent scrolling down a page that may still have elements loading and/or a stuck script, but I'm wondering whether or not there is a setting in Firefox or Chrome (or perhaps Windows in general) that will allow the scroll bar to be "released" even though the browser may be busy? It may be "2002" of me, but I wouldn't mind being able to scroll along gradually, even if the page hasn't had time to fully render all of the images, etc., yet. Does such an advanced setting exist "under the hood"?

  Read the article

• Windows 7 Loading Very Slow

  - by Adnan

  Hi guys, I've had a problem that only started to occur yesterday. When I boot into Windows 7 and log on to my user account, the computer gets very laggy and slow for at least 5 minutes. Icons take ages to load, and everything is rendered unclickable. This happens for about five minutes after which everything goes back to normal. I tried restarting a few times to see if this is a recurring problem, and it is. I ran a full system scan with Microsoft Security Essentials and found nothing wrong, and I also defragmented the disk to increase performance. However, the problem still exists. Edit: For the past day, I've been trying to install Ubuntu on the same laptop. When installing it on a partition didn't work, I decided to use Wubi. Could this somehow be the problem? Also, my hard drive gets hot a lot, so could the heat be affecting the hard drive and maybe making it defective? Any help on this issue would be greatly, greatly appreciated.

  Read the article

• Setting up subdomain to respond on :443 with apache2

  - by compucuke

  I read through some guides on this and I believe it is possible to have apache respond to a subdomain through ssl. I have domain.com responding on 80 and I do not need domain.com responding on 443. Rather, the only use I have for ssl is for the subdomain sub.domain.com. So my site should be http://domain.com http://www.domain.com https://sub.domain.com https://www.sub.domain.com My CNAME records are as follows sub.domain.com xxx.xx.xx.xxx *.sub.domain.com xxx.xx.xx.xxx The A record exists but should not matter for the example. I set up a separate config file in sites-enabled for sub.domain.com NameVirtualHost xxx.xx.xx.xxx:443 <VirtualHost xxx.xx.xx.xxx:443> SSLEngine on SSLStrictSNIVHostCheck on SSLProtocol -ALL +SSLv3 +TLSv1 SSLCipherSuite ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:-MEDIUM ServerAlias sub.domain.com DocumentRoot /usr/local/www/ssl/documents/ SSLCertificateFile /root/sub.domain.com.crt SSLCertificateKeyFile /root/sub.domain.com.key Alias /robots.txt /usr/local/www/ssl/documents/robots.txt Alias /favicon.ico /usr/local/www/ssl/documents/favicon.ico Alias /js/libs /usr/local/www/ssl/documents/js/libs Alias /media/ /usr/local/www/documents/media/ Alias /img/ /usr/local/www/ssl/documents/img/ Alias /css/ /usr/local/www/ssl/documents/css/ <Directory /usr/local/www/ssl/documents/> Order allow,deny Allow from all </Directory> WSGIDaemonProcess sub.domain.com processes=2 threads=7 display-name=%{GROUP} WSGIProcessGroup sub.domain.com WSGIScriptAlias / /usr/local/www/wsgi-scripts/script.wsgi <Directory /usr/local/www/wsgi-scripts> Order allow,deny Allow from all </Directory> </VirtualHost> Now, it is important to mention that https://domain.com responds with what I have running from script.wsgi above instead of on https://sub.domain.com. It does not respond to sub.domain.com. checking https://sub.domain.com causes a 105 error. This is a DNS error but I am convinced the DNS does not have a problem with the CNAME records, they just point to my IP. Am I doing something that Apache can not do?

  Read the article

• Streaming to PS3 with NAS and built-in dlna server?

  - by philt

  With consumer-grade hardware, is it possible to successfully stream 1080p mp4 videos to a PS3? I have a linksys router that can only do 10/100. The PS3 is wired to it with cat5e cable, and the PS3 itself supports gigabit ethernet. I would upgrade the router and get one that supports gigabit ethernet if it could handle streaming like this. It currently does work with minor jerkiness streaming from my mac to the PS3, but fast-forward/reverse and "goto" (equivalent of scene selection) take forever and/or fail completely. And streaming from my mac of course requires the mac to be on at all times. When I put the movies on an external USB drive and connect to the PS3 directly, it performs flawlessly. Fast forward and everything works great. So I was thinking about getting a NAS, but I don't know if any inexpensive NAS (i.e. Buffalo Linkstation Live, WD My Book World Edition, D-Link DNS-321, etc.) can actually deliver the performance necessary to do this, even with gigabit ethernet?

  Read the article

• Why are my socks proxies slow

  - by vps_newcomer

  I have a linux vps, and i have tried a few socks proxy setups to test their performance: All tests were using speedtest.net The standard ssh tunnel proxy 0.8mbit/s download and 0.1-0.2mbit/s upload speeds dante-server proxy 1.3mbit/s download and 0.4-0.5mbit/s upload I am wondering why are these speeds so slow? Is anything shaping them? Is it just the nature of socks proxies? I know that the ssh tunnel has to do encryption and what not so that is why its slow, but i was surprised to see that the second setup was also quite slow. On the VPS i have received download speeds of 25MB/s per second (thats about 200mbit/s and upload speed of atleast 5MB/s (haven't got a good enough pipe to test anything faster). The other option i was going to try is to setup OpenVPN and see how that goes, however i need to find a good tutorial as it's fairly complicated to setup. So why is it so slow? How can i test to see where the bottleneck is? How can i make it faster :D

  Read the article

• Why are FMS logs filled with 'play' event status code 408 for a failed webcast?

  - by Stu Thompson

  Recently we had a live webcast event go horribly wrong. I'm doing the technical post-mortem, with limited information. We know that the hardware encoder (a Digital Rapid Touch Stream Web HDI) was unable to send upstream at a sustained reliable high rate. What we don't know is if the encoder's connection was problematic (Zürich), or that of the streaming server (in Frankfurt). Unfortunately, I've got three different vendors all blaming each other (the CDN who runs the server, the on-site ISP and the on-site encoding team.) In the FMS log files I see a couple of interesting things: Zillions of Status Code 408 on play event entries for clients. Adobe's documentation stats that this "Stream stopped because client disconnected". ("Zillions" would be a ratio of 10 events for every individual IP address.) Several unpublish / (re)publish events per hour for the encoder I'd like to know if all those 408s could tell me with authority that the FMS server was starved for bandwidth, or that the encoding signal was starved (and hence the server was disconnecting clients.) Any clues?

  Read the article

• ASUS EAH5450 Graphics Card (ATI Radeon HD5450 - 1 GB DDR3) on Windows 2003? Anybody got it to work?

  - by JJarava

  Hi all! I've just bought an ASUS EAH5450 Graphics Card (ATI Radeon HD5450, 1 GB DDR3) for my main system, but I haven't been able to make it work under Windows 2003 (my OS in that system). When I plugged the card, I got a couple of "installing drivers" prompt for things such as "ATI High Definition Audio Device" that got themselves sorted out of the Internet, and then a "Standard VGA Graphics Adapter". The CD that came with the card installs something called "ATI Catalyst Install Manager" and .net 2.0, but no drivers. I've downloaded the latest (WinXP 32bits) drivers from ATI, and the experience is the same: I don't get any drivers installed. My Motherboard is an ASUS A8N-SLI with nVidia nForce 4 chipset (for an Athlon 64X2, somewhat old), but my previous card was an ATi Radeon X700, so it's been working with ATI cards before. On POST, during boot I see a "Display Card" Device (Vendor ID 1002-68F9-0300) and a "Multimedia Device" (1002-AA68-0403), and when viewing the properties of the "Standard VGA", they match the device ID. Any hints? I'd really hate having to get rid of the card, and I'm sure it's not that strange what I'm trying to do...

  Read the article

• Defeating the RAID5 write hole with ZFS (but not RAID-Z) [closed]

  - by Michael Shick

  I'm setting up a long-term storage system for keeping personal backups and archives. I plan to have RAID5 starting with a relatively small array and adding devices over time to expand storage. I may also want to convert to RAID6 down the road when the array gets large. Linux md is a perfect fit for this use case since it allows both of the changes I want on a live array and performance isn't at all important. Low cost is also great. Now, I also want to defend against file corruption, so it looked like a RAID-Z1 would be a good fit, but evidently I would only be able to add additional RAID5 (RAID-Z1) sets at a time rather than individual drives. I want to be able to add drives one at a time, and I don't want to have to give up another device for parity with every expansion. So at this point, it looks like I'll be using a plain ZFS filesystem on top of an md RAID5 array. That brings me to my primary question: Will ZFS be able to correct or at least detect corruption resulting from the RAID5 write hole? Additionally, any other caveats or advice for such a set up is welcome. I'll probably be using Debian, but I'll definitely be using Linux since I'm familiar with it, so that means only as new a version of ZFS as is available for Linux (via ZFS-FUSE or so).

  Read the article

• java max heap size, how much is too much

  - by brad

  I'm having issues with a JRuby (rails) app running in tomcat. Occasionally page requests can take up to a minute to return (even though the rails logs processed the request in seconds so it's obviously a tomcat issue). I'm wondering what settings are optimal for the java heap size. I know there's no definitive answer, but I thought maybe someone could comment on my setup. I'm on a small EC2 instance which has 1.7g ram. I have the following JAVA_OPTS: -Xmx1536m -Xms256m -XX:MaxPermSize=256m -XX:+CMSClassUnloadingEnabled My first thought is that Xmx is too high. If I only have 1.7gb and I allocated 1.5gb to java, i feel like I'll get a lot of paging. Typically my java process shows (in top) 1.1g res memory and 2g virtual. I also read somewhere that setting the Xms and Xmx to the same size will help as it eliminates time spend on memory allocation. I'm not a java person but I've been tasked with figuring out this problem and I'm trying to find out where to start. Any tips are greatly appreciated!! update I've started analyzing the garbage collection dumps using -XX:+PrintGCDetails When i notice these occasional long load times, the gc logs go nuts. the last one I did (which took 25s to complete) I had gc log lines such as: 1720.267: [GC 1720.267: [DefNew: 27712K->16K(31104K), 0.0068020 secs] 281792K->254096K(444112K), 0.0069440 secs] 1720.294: [GC 1720.294: [DefNew: 27728K->0K(31104K), 0.0343340 secs] 281808K->254080K(444112K), 0.0344910 secs] about 300 of them on a single request!!! Now, I don't totally understand why it's always GC'ng from ~28m down to 0 over and over.

  Read the article

• Curios: What makes CPUs better than others? [closed]

  - by Zizma

  I have been wondering about this for a long while now and was hoping someone here could answer it pretty easily. If I was looking for the most powerful CPU what should I really be looking at? There are so many different parameters of a CPU and I am wanting to know what each thing does and what really matters. Basically this: What is the deal with cores? If I take using optimized applications out of the mix would it theoretically better to get quad core 1.0GHz CPU or a 1 core 4 GHz CPU? Also, what is the difference between maybe an Sandy Bridge CPU versus an Ivy Bridge CPU? If they both were had the same clock speed and number of cores would the Ivy Bridge perform better? Does an older Xeon with an equal clock speed and number of cores to a new i7 really perform worse/slower? Does size matter? Why would I go with a 22nm CPU over a 32nm when the size difference is so trivial? What about the cache? When does the cache come into play with performance?

  Read the article

• Using ZFS or XFS on a Xen guest running Linux

  - by zoot

  Background: I'm investigating the viability of using a filesystem other than ext3/4, with the ability to run snapshots for backup and rollback purposes. The servers under consideration are mailbox server nodes running on Linode's Xen based VPS platform. I'm particularly drawn to the various published benefits which ZFS offers in terms of data integrity and this year's stable release of native ZFS support in Linux - http://zfsonlinux.org ZFS appears to be the more thorough option in terms of benefits and simplicity (instead of LVM+XFS). Please note that I have little experience with ZFS (which I use on a local FreeNAS installation) and none with XFS, hence the post. To date, my servers are using ext3 filesystems, not managed under LVM. Question in detail: So, I have two questions. (1) Which of the two filesystems would be the better choice for the best of all of the following 3 aspects, running on a Xen Linux guest? Snapshots Data Integrity Performance (2) If ZFS is a viable option, is it practical to use ZRAID across Xen disk images to further enhance the solution for data integrity? Note: I'm reluctant to consider btrfs, given the many warnings I've read about in using it on production systems.

  Read the article

• Why is this APC installation failing so badly?

  - by Matt

  I have multiple instances of APC running on my server with similar configurations (albeit with different cache sizes. However, one of the instances is performing extremely poorly, and I have no idea why (100% cache fragmentation, high miss rate). The runtime settings I'm using are as follows (pretty much out of the box): apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 1M apc.mmap_file_mask apc.num_files_hint 1000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.shm_segments 1 apc.shm_size 10M apc.slam_defense 1 apc.stat 1 apc.stat_ctime 0 apc.ttl 0 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 0 apc.write_lock 1 APC is version 3.1.6, PHP is 5.3.3-1ubuntu9.5. I've tried restarting Apache multiple times, so this isn't a freak instance. The instance with problems is simply running Wordpress with a few plugins installed. All other instances (~4) on the server are running perfectly fine with almost 100% hit rates and 0% fragmentation; for example this instance is holding a website built using the Symfony framework. Any help would be much appreciated; I haven't had much experience with APC and was hoping for it to be an out-of-the-box speed boost ;).

  Read the article

• File download speed issue over a dedicated fibre link

  - by nixnotwin

  My ISP has installed a fibre based dedicated internet connection at the place where I work. In the beginning the connection terminated at one of the ISP's core routers. It resulted in a strange issue. Eventhough the assigned speed was 5mbps, when tests were done by downloading large files over http and ftp from multiple locations, the speed never went above 2mbps. But bittorrent downloads reached 5mbps. Even file download from the ISP servers were fine. So, at the ISP our link was attached directly to their edge router. After this file downloads from high bandwidth servers, like Google and MS, reached the 5 mbps limit. Sometimes the speed would fall down below 2 mbps and suddenly it will go up to the 5 mbps limit ( it keeps on happening during any single file download). But other downloads like ubuntu apt repositories still struggle to go above 2 mbps. The engineers at the ISP have not been able to sort out the issue. After they moved us to their edge router instead of giving us 8 public ip's, they just gave 4 ip's. When we enquired about it, they told us that giving more ip's would result in arp overload at their edge router. But somehow I was able to convince them to give us the 8 ip's which we wanted. But the file download issue has remained. What might be the reason for files from different location getting downloaded with different speeds, that too with heavy fluctuation in speeds? I have downloaded files from same url's from a connection belonging to another smaller ISP, and the speeds were fine and reached full 5 mbps limit.

  Read the article

< Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >