Search Results

Search found 18954 results on 759 pages for 'connection reset'.

Page 622/759 | < Previous Page | 618 619 620 621 622 623 624 625 626 627 628 629  | Next Page >

• Unable to connect remotely to Vsftpd server set up on CentOS VirtualBox

  - by ryekayo

  I have set up a Vsftp server using the following instructions provided Here and even went as far as following the commentary at the bottom. But I am unable to connect remotely. When I attempt to use FileZilla or my Ubuntu terminal, I always get: ryan@ryan-Galago-UltraPro:~$ ftp 10.0.x.xx ftp: connect: Connection timed out ftp> I have checked and re-checked iptables conf file and made sure that Port 21 is being Accepted and it is. I have looked this up on the web and decided to try nmap to port scan it and this is what I get for a result: ryan@ryan-Galago-UltraPro:~$ nmap -PN 10.0.xx.xx Starting Nmap 6.40 ( http://nmap.org ) at 2014-08-19 15:01 EDT Nmap scan report for 10.0.xx.xx Host is up. All 1000 scanned ports on 10.0.xx.xx are filtered Nmap done: 1 IP address (1 host up) scanned in 201.38 seconds Is there anything else that I should do or check for? UPDATE: I have tried to ping from the virtual machine to my IP address on Ubuntu and have been successfully able to. I cannot ping to my virtual machine from Ubuntu. I have narrowed this down to possibly being a firewall related issue on Ubuntu's side, but why would I be unable to connect from FileZilla?

  Read the article

• Make dhcp assign same IP and hostname for different interfaces at one machine

  - by Egeshi

  I have a feeling that question itself looks stupid but it is not. Please let me clarify. I have dynamic DNS with BIND and NIS configured at my LAN and have laptop which I am using in both wireless and wired mode. I mean that sometimes I have to use wired interface to achieve higher throughput but most of time I don't need it and using wireless mode. Everything works great. Issue is that I want both interfaces get same IP from DHCP. Just for convenient firewall setup. If I add both hosts to dhcp in this manner # bt wireless host bt { hardware ethernet 00:1f:1f:62:60:28; fixed-address 172.16.77.110; } # bt wired host bt { hardware ethernet 00:14:22:b7:5a:de; fixed-address 172.16.77.110; } DHCP says logs following message dhcpd: Dynamic and static leases present for 172.16.77.110 dhcpd: Remove host declaration bt-wired or remove 172.16.77.110 dhcpd: from the dynamic address pool for 172.16/16 Host records are added outside of any subnet, but it makes no difference if I put them there, effect is still the same. This is not critical but either is not my whim because even if DHCP seems to work fine for that "bt" host, I cannot make connection TO it from remote machine anymore with this definitely incorrect DHCP config. I'd be thankful if one spares a minute for advice about how to configure DHCPD correctly. UPDATE. I realize that there's a soulution to assign different hostname in DHCP config but would like to use benefits of short host names.

  Read the article

• netconfig won't change DNS on opensuse 12.2

  - by Krystian

  I'm trying to update my dns servers after openvpn connection, but netconfig won't do that for me. Here's how I'm trying to do it [manually now]: /sbin/netconfig modify -v -i tap0 -s openvpn <<-EOF INTERFACE='tap0' DNSSERVERS='10.10.0.1' EOF And here's the verbose output: debug: lockfile created (/var/run/netconfig.pid) for PID 5530 debug: lockfile created debug: write new STATE file /var/run/netconfig//tap0/netconfig0 debug: Module order: dns-resolver dns-bind dns-dnsmasq nis ntp-runtime debug: dns-resolver module called debug: Static Fallback debug: Use NetworkManager policy merged settings debug: exec get_dns_settings: /var/run/netconfig/NetworkManager.netconfig debug: get_dns_settings: service 'NetworkManager' => rank '1' debug: get_dns_settings: DNS_SEARCHLIST_1='mydomain.com' debug: get_dns_settings: DNS_SERVERS_1='192.168.0.1' debug: exit get_dns_settings: /var/run/netconfig/NetworkManager.netconfig debug: write_resolv_conf: ' mydomain.com ' ' 192.168.0.1 ' debug: No changes for /etc/resolv.conf debug: dns-bind Module called debug: dns-dnsmasq Module called debug: nis Module called debug: Static Fallback debug: Use NetworkManager policy merged settings debug: exec get_nis_settings: /var/run/netconfig/NetworkManager.netconfig debug: exit get_nis_settings: /var/run/netconfig/NetworkManager.netconfig debug: set_nisdomainname: eth0 24 debug: set_nisdomainname: => yes debug: set_nisdomainname: old[]=, new[24]= debug: format_yp_conf called with : debug: Using static fallback debug: format_static[0] called debug: No changes for /etc/yp.conf debug: nis domainname '' is up to date debug: ntp-runtime Module called debug: Static Fallback debug: Use NetworkManager policy merged settings debug: exec get_ntp_settings: /var/run/netconfig/NetworkManager.netconfig debug: get_ntp_settings: NTP_SERVER_LIST='' debug: exit get_ntp_settings: /var/run/netconfig/NetworkManager.netconfig I've been trying to find something relevant on the web, but failed to do so. I have no other clue on how to progress with this issue. Any thoughts?

  Read the article

• Port forwarding for samba

  - by EternallyGreen

  Alright, here's the setup: Internet - Modem - WRT54G - hubs - winxp workstations & linux smb server. Its basically a home-style distributed internet connection setup, except its at a school. What I want is remote, offsite smb access. I figured I'd need to find out which ports need forwarding and then forward them to the server on the router. I'm told in another question on SF that multiple ports will need forwarding, and it gets somewhat complicated. One of the things I need to know is which ports require forwarding for this, and what complications or vulnerabilities could arise from this. Any additional information you think I should have before doing this would be great. I'm told SMB doesn't support encryption, which is fine. Given I set up authentication/access control, all this means is that once one of my users authenticates and starts downloading data, the unencrypted traffic could be intercepted and read by a MITM, correct? Given that that's the only problem arising from lack of encryption, this is of no concern to me. I suppose that it could also mean a MITM injecting false data into the data stream, eg: user requests file A, MITM intercepts and replaces the contents of file A with some false data. This isn't really an issue either, because my users would know that something was wrong, and its not likely anyone would have incentive to do this anyway. Another thing I've been informed of is Microsoft's poor implementation of SMB, and its crap track record for security. Does this apply if only the client-end is MS? My server is linux.

  Read the article

• Wireless disconnect randomly with wpa_supplicant reason=2

  - by renenglish

  I installed ubuntu-server 12.04 on my PC , and I use an usb wireless card to join the network. It works ok when I boot up my PC , but the wireless disconnects after a while. I pkill wpa_supplicant and reload the driver rtl8192cu , then it works a again. Then it disconnect again after about a random minutes. Here is the syslog: 22384 May 29 21:49:27 homecenter kernel: [ 6450.459313] wlan1: authenticated 22385 May 29 21:49:27 homecenter kernel: [ 6450.459535] wlan1: associate with f4:ec:38:45:62:74 (try 1) 22386 May 29 21:49:27 homecenter kernel: [ 6450.469080] wlan1: RX AssocResp from f4:ec:38:45:62:74 (capab=0 x431 status=0 aid=3) 22387 May 29 21:49:27 homecenter kernel: [ 6450.469085] wlan1: associated 22388 May 29 21:49:27 homecenter wpa_supplicant[2342]: Associated with f4:ec:38:45:62:74 22389 May 29 21:49:27 homecenter kernel: [ 6450.481933] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 22390 May 29 21:49:27 homecenter wpa_supplicant[2342]: WPA: Key negotiation completed with f4:ec:38:45:62:7 4 [PTK=CCMP GTK=CCMP] 22391 May 29 21:49:27 homecenter wpa_supplicant[2342]: CTRL-EVENT-CONNECTED - Connection to f4:ec:38:45:62: 74 completed (auth) [id=0 id_str=] 22392 May 29 21:49:38 homecenter kernel: [ 6461.472014] wlan1: no IPv6 routers present 22393 May 29 21:49:38 homecenter ntpdate[2263]: step time server 91.189.94.4 offset 0.012758 sec 22394 May 29 21:49:51 homecenter ntpdate[2404]: step time server 91.189.94.4 offset -0.001190 sec 22395 May 29 21:54:38 homecenter kernel: [ 6762.052030] wlan1: deauthenticated from f4:ec:38:45:62:74 (Reas on: 2) 22396 May 29 21:54:38 homecenter wpa_supplicant[2342]: CTRL-EVENT-DISCONNECTED bssid=f4:ec:38:45:62:74 reas on=2 22397 May 29 21:54:38 homecenter kernel: [ 6762.064744] cfg80211: All devices are disconnected, going to re store regulatory settings 22398 May 29 21:54:38 homecenter kernel: [ 6762.064752] cfg80211: Restoring regulatory settings 22399 May 29 21:54:38 homecenter kernel: [ 6762.064757] cfg80211: Calling CRDA to update world regulatory d omain 22400 May 29 21:54:38 homecenter kernel: [ 6762.069938] cfg80211: Ignoring regulatory request Set by core s ince the driver uses its own custom regulatory domain 22401 May 29 21:54:38 homecenter kernel: [ 6762.069943] cfg80211: World regulatory domain updated: 22402 May 29 21:54:38 homecenter kernel: [ 6762.069945] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 22403 May 29 21:54:38 homecenter kernel: [ 6762.069949] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22404 May 29 21:54:38 homecenter kernel: [ 6762.069952] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22405 May 29 21:54:38 homecenter kernel: [ 6762.069956] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22406 May 29 21:54:38 homecenter kernel: [ 6762.069959] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22407 May 29 21:54:38 homecenter kernel: [ 6762.069962] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KH z), (300 mBi, 2000 mBm)

  Read the article

• ADSL with RFC 2684 Bridging

  - by Axel Isouard

  My new ADSL line is now enabled, I can finally use my Netgear DM111Pv2 to use to the Internet. My ISP has told me a big surprise : I don't need to use a login and a password to connect to the Internet, then I must use the RFC 2684 bridging mode. It works pretty fine on the ADSL modem's side, but I've spent one night trying to figure out how to connect to the Internet through this modem. I only have a Fonera 2.0n and a computer running Gentoo Linux. I've been trying to use the br2684ctl utility with brctl on my Gentoo, first I've configured my kernel in that way : CONFIG_PPP=y CONFIG_PPP_BSDCOMP=y CONFIG_PPP_DEFLATE=y # CONFIG_PPP_FILTER is not set CONFIG_PPP_MPPE=y # CONFIG_PPP_MULTILINK is not set CONFIG_PPPOATM=y CONFIG_PPPOE=y CONFIG_PPP_ASYNC=y CONFIG_PPP_SYNC_TTY=y [...] CONFIG_ATM=y CONFIG_ATM_CLIP=y CONFIG_ATM_CLIP_NO_ICMP=y CONFIG_ATM_LANE=y CONFIG_ATM_MPOA=y CONFIG_ATM_BR2684=y # CONFIG_ATM_BR2684_IPFILTER is not set And I still get these messages : cirus nais # br2684ctl -b -c 0 -e 0 -a 8.35 br2684ctl[8041]: Interface "nas0" created sucessfully br2684ctl[8041]: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl[8041]: Fatal: failed to connect on socket; No such device The brctl utility keeps telling me "Invalid argument" each time I try to add the nas0 interface into my bridge, I'm honestly hoping I'm doing wrong. I've been following this README carefully and this tutorial on setting up a PPPoE connection with Gentoo, but the PPPoE interface just tries to start, and nothing special related to PPP happens, I can't see the interface when I do ifconfig. So, I'm asking you if there's something huge I've been missing since the beginning ! Maybe I should wait to buy a new router fully supporting the RFC2684 bridging mode, but I'm more interested in setting up this mode on my Fonera 2.0n and even my Raspberry Pi !

  Read the article

• How can ICS in Windows 7 be managed via command line, scripts, config files, etc.?

  - by Skya

  I've been using ICS successfully for years, but now I'm looking for a way to control it through something else than the GUI in Control Panel\Network and Internet\Network Connections - Connection Properties: I want to do everything that the encircled checkbox does, without touching the GUI. But what does the checkbox do? Microsoft don't provide specific information and the most helpful forum post I've found is from 2003. Assuming that some of the advice is still valid, I've come to the conclusion that ICS is broken down into 6 parts that have to be set up individually: the sharedAccess service interface settings firewall rules a static route dnsproxy autodhcp I've already learned that the service can be started/stopped with the command net start/stop sharedAccess and that netsh is a good tool for changing the interface settings and the firewall rules. But I don't understand how ICS handles routing and DNS. All hosts in my network are configured statically, so I don't care much about autodhcp. Thanks for your help! EDIT: I've spent the whole day scanning through ProcMon and I've seen reads/writes to both the registry and the filesystem and it is difficult to determine what parts of it actually make ICS work. I'm trying to look for an API instead. I'm looking into this right now, but I still want to know more about the inner workings.

  Read the article

• Linux machine can't find its tape drive

  - by Kyle Hodgson

  I have an older HP NetServer LPr with what is apparently a Symbios SCSI card connecting to a Quantum SuperLoader 3 that is DLT based. From time to time, we seem to lose the connection to the autoloader. It's usually due to flaky power, but not totally sure why; sometimes when this happens the Autoloader's LED's are orange and it needs to be power cycled. The annoying workaround currently is to reboot the machine. As it is our production VPN and DNS server in addition to being our backup server, this is less than optimal. In Debian (Sarge) is there not some command one can type to get the card to notice that it has the autoloader connected again? dcr1:/proc# grep -i symbios /proc/pci SCSI storage controller: LSI Logic / Symbios Logic 53c895 (rev 1). dcr1:/proc# uname -a Linux dcr1 2.4.27-3-686 #1 Tue Dec 5 21:03:54 UTC 2006 i686 GNU/Linux dcr1:/proc# mt status mt: /dev/tape: No such device dcr1:/proc# ls -l /dev/tape lrwxrwxrwx 1 root root 8 2007-02-07 16:01 /dev/tape -> /dev/st0 dcr1:/proc# That mt status command will show the actual st0 status when things are working correctly. The No such device message is usually the second clue that we need to reboot - the first clue is usually that the backups didn't run.

  Read the article

• What can lead to a zone memory exhaustion and how Nginx reacts to it?

  - by Miles Hughes

  What is a possible scenario for exhausting the memory designated to a connection zone with limit_conn_zone directive and what are the implication in this case? Suppose I have this in my configuration: http { limit_conn_zone $binary_remote_addr zone=connzone:1m; ... server { limit_conn connzone 5; which, according to the documentation, allocates 16000 states for connzone on a 64-bit server. It also says that If the storage for a zone is exhausted, the server will return error 503 (Service Temporarily Unavailable) to all further requests. Well, Ok. But what does it mean on practice? When does this happen? Who receives those 503s? Does it mean that if the number of IPs somehow associated with connzone hits 16000 everyone gets a 503 and it's all over? How does Nginx decide? The documentation is weirdly vague on this. So, considering the example config, who would actually get a 503 and under which circumstances and how would things go from there? Same with request zones?

  Read the article

• SMTP Unreachable from Specific Networks

  - by Jason George

  I host my business site through a VPS account. The instance runs Ubuntu and I'm using POSTFIX+Dovecot as my mail server. For the most part, the mail server works fine. I have noticed, however, that I can not send mail from specific local networks. I noticed this at a client's office serval months ago. I can receive email, but any time I tried to send mail when connected to their network the connection would time out. Since I could send my mail after leaving, I chalked it up to improper network configuration and didn't worry about it. Unfortunately I've recently moved, switched service providers, and am forced to use the service providers router due to the special set-up they put in place to give me DSL in the sticks--well beyond the typical range for a DSL run. Now I'm unable to send email from home, which is a problem. I have tried sending email through my phone (using cellular service rather than my DSL) just to confirm the server is currently working. I'm not even sure where start debugging. Any ideas on how I might track down the issue would be greatly appreciated.

  Read the article

• Convert a Linksys WAG54GP2 ADSL router into Access point only to extend my Wifi range

  - by Preet Sangha

  I have a wireless lan running on my ASDL2 connection. The router (Seimens Gigaset sx763) is provided by the ISP and is generally good. However I have couple of dead spots at the far end of the house and since I have my old router sitting in the drawer I thought that I'd try to convert it into simple WAP. However downloading the manual from linksys it seems to be that the manual is from an earlier firmware, but the very first option on the very first page seems promising: Wan Mode: Router or ADSL However after this I'm a bit lost. I know that the wireless card on this box will need a mac address and it must get its address from the master router (I thought static might be best). However the again the manual is out of date I have the option of DHCP: ON or OFF or RELAY I've not even got to the more complex options yet. Question is can this device even work this way (seems like it but I cannot find any docs on it), and if so how? Edit: Having now fiddled around I'm of the opinion that this cannot be done.

  Read the article

• Route forwarded traffic through eth0 but local traffic through tun0

  - by Ross Patterson

  I have a Ubuntu 12.04/Zentyal 2.3 server configured with WAN NATed on eth0, local interfaces eth1 and wlan0 bridged on br1 on which DHCP runs, and an OpenVPN connection on tun0. I only need the VPN for some things running on the gateway itself and I need to make sure that everything running on the gateway goes through the VPNs tun0. root:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gw... 0.0.0.0 UG 100 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 br1 192.168.1.0 * 255.255.255.0 U 0 0 0 br1 A.B.C.0 * 255.255.255.0 U 0 0 0 eth0 root:~# ip route 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.186 root:~# ip route show table main 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.D root:~# ip route show table default default via A.B.C.1 dev eth0 How can I configure routing (or otherwise) such that all forwarded traffic for other hosts on the LAN goes through eth0 but all traffic for the gateway itself goes through the VPN on tun0? Also, since the OpenVPN client changes routing on startup/shutdown, how can I make sure that everything running on the gateway itself loses all network access if the VPN goes down and never goes out eth0.

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing. EDIT: If I currently have been trying: sudo route flush sudo route add default 192.168.19.1 This gets everything to work for about a minute. But after such minute it "forgets" the routing to WiFi while retaining LAN's (en0) routing. If I unplug and replug my LAN (en0) cable, the process works for another minute.

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP.

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• Networking Home Office

  - by Matt

  I'm in the process of building an office in my garden. It's about 25m away from my house. I'd like to run a wired network connection to the office. I'd rather not go down the powerline route, as speeds don't seem great, and I'm likely to want to be moving a lot of data around on the internal network. I have an electrician who is running armoured electrical cable to the office, and is providing conduit for me to run network cable. My questions are: 1) What type of cable to run 2) How I terminate/connect it at both ends I could get something like armoured cat6 utp solid core (like this: http://www.netstoredirect.com/cat6-cable/289166-external-armoured-cat6-utp-solid-cable-price-per-metre.html) which seems fairly robust, but then I have to terminate it. Additionally, where the cable enters my house, there is about another 15m to where my router is situated. I also read this artice: http://www.audioholics.com/audio-video-cables/bjc-cat-network-cable-quality-interview which scared me into realising I don't know what I'm doing!! particularly with termination. Or I could get an "cat6 external patch cable" (e.g http://www.netstoredirect.com/rj45-network-cables/239231-external-cat6-utp-ldpe-rj45-patch-leads.html) and run that in the conduit, and work out how to terminate it at the house end. At the office end I guess I can just plug it into a switch. Any help? Thanks

  Read the article

• Monitor connected with WiDi just shows a black screen

  - by Pops

  I have a Dell XPS 18 and want to use an external monitor with it. The monitor has VGA and DVI-D inputs. The XPS 18 has no video output ports, but it does support Intel WiDi. I have a Netgear P2TV2000 WiDi receiver, but it only has composite and HDMI outputs. I'm connecting the receiver to the monitor with an HDMI cable and an HDMI/DVI-D adapter. So, in short, the video path is: Computer → WiDi → WiDi receiver → HDMI cable → HDMI/DVI-D adapter → Monitor After setting all this up, I can't get anything to display on the monitor. At the moment I power the monitor on, I can see my desktop for a brief fraction of a second, and then everything goes black. All of the relevant drivers have been updated to the latest versions. When I use a different WiDi-enabled computer to connect to the same monitor, everything works fine. When I use the original computer and receiver to connect to a TV, everything works fine. It's only when I connect the original computer to the monitor I want to use that the connection fails. What could be going wrong here, and how can I get the video to work consistently?

  Read the article

• snort analysis of wireshark capture

  - by Ben Voigt

  I'm trying to identify trouble users on our network. ntop identifies high traffic and high connection users, but malware doesn't always need high bandwidth to really mess things up. So I am trying to do offline analysis with snort (don't want to burden the router with inline analysis of 20 Mbps traffic). Apparently snort provides a -r option for this purpose, but I can't get the analysis to run. The analysis system is gentoo, amd64, in case that makes any difference. I've already used oinkmaster to download the latest IDS signatures. But when I try to run snort, I keep getting the following error: % snort -V ,,_ -*> Snort! <*- o" )~ Version 2.9.0.3 IPv6 GRE (Build 98) x86_64-linux '''' By Martin Roesch & The Snort Team: http://www.snort.org/snort/snort-team Copyright (C) 1998-2010 Sourcefire, Inc., et al. Using libpcap version 1.1.1 Using PCRE version: 8.11 2010-12-10 Using ZLIB version: 1.2.5 %> snort -v -r jan21-for-snort.cap -c /etc/snort/snort.conf -l ~/snortlog/ (snip) 273 out of 1024 flowbits in use. [ Port Based Pattern Matching Memory ] +- [ Aho-Corasick Summary ] ------------------------------------- | Storage Format : Full-Q | Finite Automaton : DFA | Alphabet Size : 256 Chars | Sizeof State : Variable (1,2,4 bytes) | Instances : 314 | 1 byte states : 304 | 2 byte states : 10 | 4 byte states : 0 | Characters : 69371 | States : 58631 | Transitions : 3471623 | State Density : 23.1% | Patterns : 3020 | Match States : 2934 | Memory (MB) : 29.66 | Patterns : 0.36 | Match Lists : 0.77 | DFA | 1 byte states : 1.37 | 2 byte states : 26.59 | 4 byte states : 0.00 +---------------------------------------------------------------- [ Number of patterns truncated to 20 bytes: 563 ] ERROR: Can't find pcap DAQ! Fatal Error, Quitting.. net-libs/daq is installed, but I don't even want to capture traffic, I just want to process the capture file. What configuration options should I be setting/unsetting in order to do offline analysis instead of real-time capture?

  Read the article

• How much network latency is "typical" for east - west coast USA?

  - by Jeff Atwood

  At the moment we're trying to decide whether to move our datacenter from the west coast to the east coast. However, I am seeing some disturbing latency numbers from my west coast location to the east coast. Here's a sample result, retrieving a small .png logo file in Google Chrome and using the dev tools to see how long the request takes: West coast to east coast: 215 ms latency, 46 ms transfer time, 261 ms total West coast to west coast: 114 ms latency, 41 ms transfer time, 155 ms total It makes sense that Corvallis, OR is geographically closer to my location in Berkeley, CA so I expect the connection to be a bit faster.. but I'm seeing an increase in latency of +100ms when I perform the same test to the NYC server. That seems .. excessive to me. Particularly since the time spent transferring the actual data only increased 10%, yet the latency increased 100%! That feels... wrong... to me. I found a few links here that were helpful (through Google no less!) ... Does routing distance affect performance significantly? How does geography affect network latency? Latency in Internet connections from Europe to USA ... but nothing authoritative. So, is this normal? It doesn't feel normal. What is the "typical" latency I should expect when moving network packets from the east coast <--> west coast of the USA?

  Read the article

• connect server to server on secondary NIC

  - by microchasm

  Hi, I have a CentOS box with multiple NIC's running Apache. I also have another box running RHEL that will be the MySQL server. I'm trying to use the secondary NIC on the Apache box to connect directly to the MySQL server, but so far no luck. I want to isolate the MySQL box as much as possible which is why I'm going for a direct connection as opposed to running through a switch. I have a crossover cable running between them. IP configs: Apache box eth0 [to lan] ip addr: 192.168.200.100 netmask: 255.255.0.0 gateway: 192.168.111.1 eth1 [to mysql] ip addr: 192.168.200.101 netmask: 255.255.0.0 gateway: [blank] MySQL box eth0 [to apache] ip addr: 192.168.200.203 netmask: 255.255.0.0 gateway: 192.168.200.201 The rest of our network is on 192.168.111.0/24 subnet. Ping only returns Destination Host Unreachable. I've tried various variations of this setup (including straight through cable), and I can't seem to get them to talk to each other. Any help appreciated.

  Read the article

• Intermittent unavailability of an instance in a failover cluster while a standby node is offline in

  - by Emil Fridriksson

  Hi everyone. I've got a small failover cluster that I run for the websites my company has. During a RAM upgrade of the standby server, our websites started to show errors about not being able to access the database server. I verified that the instance was indeed up and the server accessable via remote desktop. I also tried a SQL connection to it and it worked, but that might have been after it became available again. This happened on and off until we were able to roll back the hardware changes that were in progress on the standby server and we were able to bring it back up. There was nothing of interest in the SQL Server log, but there is a continous log for the whole duration of the problem, so there was no restart of the SQL Server service. The event viewer is of more interest, since it shows events relating to the heartbeat network card, but I don't know how that would affect the availability of the server, since the standby node is offline. I'd appreciate any help you can provide, it's not very redundant if the setup depends on the standby server being up. :) Here are the event logs from the time of the problem, I include all of them since I can't seem to see what could possibly be the cause of the problem. Event log: http://hlekkir.com:800/htmltable.htm

  Read the article

• Windows 7 PC cannot see some LAN PCs, but can access them via path

  - by zoot

  In an office LAN, with Windows 7 Professional workstations and a FreeNAS Samba server, 2 workstations have intermittent problems in browsing for the other workstations, as well as the FreeNAS server. However, so far, it appears that typing in the path to any of the workstations which aren't visible via the "browse" function, works. ie. the machine Workstation7 is not visible while browsing via Windows Explorer, but is accessible if I type \\Workstation7 in the path field. Occasionally the workstations exhibiting these symptoms show errors that their connection to the FreeNAS server has failed and only rebooting resolves the issue. All other workstations on the network use identical Windows 7 Professional installations and never have these problems. I've checked all machines and they're not using Home Groups. All are setup on the same WorkGroup as the FreeNAS server and the network type is set to Work Network. Temporarily disabling the firewall on the workstations with the issue made no difference, so I know this has nothing to do with the firewall settings. Any pointers would be appreciated. Thanks.

  Read the article

• ipv6 port 445 does not accept the request from a global type address

  - by blacktea

  I want to scan the port 445 in windows server 2003, but my scanner only have one type ipv6 address which is global not link-local. When I do this,I find that I can't find port 445 open. But I use the command "netstat -an" to assure the port 445 is listening. Finally I find this confusing phenomenon: 1.when I set a link-local ddress in my scanner, then it will work in scanning port 445. 2.when I only set a global address in my scanner, it doed not work. This means if a host with a link-local address use socket to send a syn packet to the port 445 in server 2003, it will receive a ack packet. But if with a global address it will receive a rst packet. Thus, I can't scan the port 445 in server 2003 with a global address. I need to know why? Can anybody help? And I use the netsh-firewall to check the exception and netsh-interface-ipv6 to turn off the firewall on the specific interface. Still can't establish the connection with port 445, do you have any ideal about this ?

  Read the article

• Windows 7 Media Center PC not displaying MKV files properly

  - by David

  Does anyone know why Windows Media Center wouldn't correctly display a 16x9 video? I just upgraded my home-built HTPC from Vista Ultimate (hey, it was a giveaway) to Windows 7 Ultimate - clean install. After that, I installed the Divx7 beta (to get .MKV support) and AC3filter (so I could HEAR the MKV files). Previously, under Vista Ultimate (32 bit), I had Arcsoft's Total Theater Pro for playing Blu-Rays and MKV decoding under Media Center. Now when I play a 720p 16x9 MKV file, I get some 'letterboxing' - like it's halfway between 4x3 and 16x9 - with the aspect ration looking alightly squished as a result. Here's the wierd part. If I use the Media Center connection software in my XBox 360 - it plays perfectly, filling the 16x9 screen edge-to-edge, just like Vista's WMC software USED to. Of course, beats the network up because the XBox goes to the HTPC, the HTPC goes to my WHS machine to fetch the data, it comes back to the HTPC, gets transcoded and streamed back to the Xbox. I'm running the latest drivers for an NVidia card (as fetched by Windows 7). I have no idea WHY this is because if I play "ordinary" (i.s. SD) Divx files that are 16x9, they play just fine, scaled right up to my screen's edges. It puzzles me as to why the same machine that properly converts the bits for the Xbox can't display/scale them properly for the attached display. Mind you, Windows Media Player exhibits the same symptoms. Ideas?

  Read the article

• Sendmail in Nexenta core 3.0.1

  - by maximdim

  I'm trying to setup sendmail in Nexenta core 3.0.1 (Solaris based OS). All I want is to be able to send emails from that host - like notifications about failures, cron jobs output etc. Initially Nexenta core doesn't have sendmail so here is what I've done: apt-get install sunwsndmu Now there is a sendmail in /usr/sbin/sendmail. When I try to send email from command line: $mail maxim test . It doesn't give me any error but in log file I see: Dec 20 12:41:08 nas sendmail[12295]: [ID 801593 mail.info] oBKHf8u7012295: from=maxim, size=107, class=0, nrcpts=1, msgid=<201012201741.oBKHf8u7012295@nas>, relay=maxim@localhost Dec 20 12:41:08 nas sendmail[12295]: [ID 801593 mail.info] oBKHf8u7012295: to=maxim, ctladdr=maxim (1000/10), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30107, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection refused by [127.0.0.1] So I guess I need to have SMTP service running. How do I do that in Nexenta? svcs -a | grep sendmail doesn't return anything and # svcadm enable sendmail svcadm: Pattern 'sendmail' doesn't match any instances I'm not married to sendmail so if there are easier ways to achieve y goal I'm open to suggestions as well. Thanks,

  Read the article

• How this could happen to my ftp server?

  - by srisar

  hi, again me, i just dont get why i m getting this message, when i try to connect my ftp server thorugh my wan address (112.135.26.115) its saying me, 530 user access denied but when i give the same data to http://ftptest.net the result is as follows... Status: Resolving address of 112.135.26.115 Status: Connecting to 112.135.26.115 Status: Connected, waiting for welcome message Reply: 220-FileZilla Server version 0.9.34 beta Reply: 220-written by Tim Kosse ([email protected]) Reply: 220 Please visit http://sourceforge.net/projects/filezilla/ Status: CLNT http://ftptest.net on behalf of 112.135.26.115 Reply: 200 Don't care Status: USER saravana Reply: 331 Password required for saravana Status: PASS ********* Reply: 230 Logged on Status: SYST Reply: 215 UNIX emulated by FileZilla Status: FEAT Reply: 211-Features: Reply: MDTM Reply: REST STREAM Reply: SIZE Reply: MLST type*;size*;modify*; Reply: MLSD Reply: AUTH SSL Reply: AUTH TLS Reply: UTF8 Reply: CLNT Reply: MFMT Reply: 211 End Status: PWD Reply: 257 "/" is current directory. Status: Current path is / Status: TYPE I Reply: 200 Type set to I Status: PASV Reply: 227 Entering Passive Mode (112,135,26,115,43,9) Status: MLSD Reply: 150 Connection accepted Listing: type=dir;modify=20100322113235; it_is_working!_Andrejs_Cainikovs_from_serverfault.com Listing: type=file;modify=20100322110559;size=5; New Text Document.txt Reply: 226 Transfer OK Status: Success can anyone say why this happens to me? please im trying the whole day!!

  Read the article

< Previous Page | 618 619 620 621 622 623 624 625 626 627 628 629  | Next Page >