Search Results

Search found 22224 results on 889 pages for 'point of sale'.

Page 625/889 | < Previous Page | 621 622 623 624 625 626 627 628 629 630 631 632  | Next Page >

• exim4 to relay emails

  - by Matthieu

  I have exim4 installed on a Linux box. The basics work fine and I can send email from that machine without any problem to whatever email address. I also have a printer/scanner which is capable to send scans as emails. It needs an SMTP gateway to be able to do that. So I give the IP address of that Linux box, changed the configuration a little bit but still cannot get it to work. After I run dpkg-reconfigure exim4-config, here is what I get in /etc/exim4/update-exim4.conf.conf : dc_eximconfig_configtype='internet' dc_other_hostnames='' dc_local_interfaces='127.0.0.1;192.168.2.2' dc_readhost='' dc_relay_domains='mycompanyemail.com' dc_minimaldns='false' dc_relay_nets='192.168.2.0/24' dc_smarthost='' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='' dc_mailname_in_oh='true' dc_localdelivery='mail_spool' My problem is that with this configuration, I can only send to emails @mycompanyemail.com... It says I can use wildcard, but when I do that, the '*' is replaced by whatever filename is in the directory where I run all that. How can I configure it to be able to send emails with any domain ? Or am I doing it wrong ? EDIT : here is the part of the log that's causing trouble : 2011-08-03 16:28:18 H=(NPI2D389C) [192.168.2.20] F=<[email protected]> rejected RCPT <[email protected]>: relay not permitted The first part ([email protected]) does not matter. I changed the email address. The point is that if this email is @mycompanyemail.com then everything works fine. Anything else does not work. I could add gmail.com, but I am looking to have any domain working...

  Read the article

• How can I debug user mode driver failures in Windows 8

  - by Tom

  I have a 32 GB SD Card. Whenever I insert this card in to my newly upgraded Windows 8 laptop the OS stops responding normally. Metro Apps won't work. The system may or may not log in. Desktop apps may or may not be able to do things. When I remove the card and restart then all is fine. As soon as I put the card back in, the system starts misbehaving again. I've run Windows Update, so I have the latest drivers from Microsoft. This does not occur with the 8 GB cards I have. Unfortunately I only have one 32 GB card, so I can't test with others. From examining the system event log I've determined this is happening due to a user mode driver failure. How can I best debug this issue from here? How can I figure out which driver this is related to? Will there be a Dr. Watson crash dump somewhere? Details - System - Provider [ Name] Microsoft-Windows-DriverFrameworks-UserMode [ Guid] {2E35AAEB-857F-4BEB-A418-2E6C0E54D988} EventID 10110 Version 1 Level 1 Task 64 Opcode 0 Keywords 0x2000000000000000 - TimeCreated [ SystemTime] 2012-10-29T00:51:57.532718300Z EventRecordID 40417 Correlation - Execution [ ProcessID] 1056 [ ThreadID] 3796 Channel System Computer thebrain - Security [ UserID] S-1-5-18 - UserData - UMDFHostProblem [ lifetime] {811E3DC4-FBC6-420B-ABCC-AD7505A36F3B} - Problem [ code] 3 [ detectedBy] 2 ExitCode 3 - Operation [ code] 259 Message 72448 Status 4294967295 Edit 1 So I tried using Debug View from SysInternals (you can get it here: http://technet.microsoft.com/en-us/sysinternals/bb896647.aspx). That gave me this information: which is not especially helpful. Then I tried connecting WinDbg to WUDFHost.exe (the process that seems to host user mode drivers) to see if it could catch the error. Get it here: http://msdn.microsoft.com/en-US/windows/hardware/hh852363 Instructions: http://msdn.microsoft.com/en-US/library/windows/hardware/ff554716(v=vs.85).aspx That didn't help much. It didn't catch any exceptions as I'd hoped (which would point me to the cause of the crash at least). Here's the stack of one of the threads:

  Read the article

• Windows Server 2003 SBS domain in multiple sites

  - by E3 Group

  We have about 25 employees in our current office and are looking to open up another office in another capital city housing about 15 employees. In our current office, we are running a domain hosted by a 2003 SBS server and I've been tasked by the boss to expand our infrastructure to the new office in the cheapest way possible (cheapest way in the short run that is, because my boss doesn't think more than 6 months ahead). So I'm looking to get a second hand server and have it run Server 2003 Std with exchange server 2003. These are the things that it needs to do: Replicate shared folders that are hosted in the parent LAN. Deliver emails hosted in the parent Exchange Server Somehow link up with the parent domain controller and push the AD to the remote site I'm pretty sure 3 is impossible but the DC would be available if a VPN connection is present, right? On that note, would I be looking at hardware VPN connections? I'm not sure how to deploy the new site as this is my first time doing it and i'm making it especially difficult for myself, seeing as the AD and DC is on an SBS server. Would I first start by establishing a VPN connection and then joining the new server to the domain? Will things 'just work' if I install exchange onto the new server and point outlooks to it? and how would I be able to replicate shared folders?

  Read the article

• Connect over WiFi to SQL Server from another computer

  - by Bronzato

  I tried to connect over WiFi to SQL Server with SQL Server Management Studio from another computer, but it failed. I have a computer with Windows 7 & SQL Server 2008 (lets say the server computer). Next to it I have a freshly installed computer with Windows 7 & SQL Server Management Studio (let's say the client computer). What I did on the server computer: Configure firewall by enabling port 1433 Enabled network protocols (TCP/IP) inside SQL Server Configuration Manager Checked Allow remote connections to this server in server properties in the SQL Server Management application. Started SQL Server Browser Restarted services (SQL Server Browser is stopped at this point, but I don't think it is necessary. Is it?) Next, I successfully tested a ping on the port 1433 from my client computer with a tool named tcping (ex: tcping 192.168.1.4 1433). But I still cannot connect from my client computer to SQL Server on my server computer. Ok, something new with this problem: Until now, I successfully connected to my "server computer" with Management Studio. What I did is type the computer name in the server name field in the connection window of Management Studio. My previous (failed) attempt was to type the computer name followed by the instance of SQL server (ex: COMPUTER_NAME\SQL2008). I don't know why I only have to type the computer name. Now my new challenge is to be successful in connecting my VB6 application to this remote database located on my "server computer". I have a connection string for this but it failed to connect. Here is my connection string: "Provider=SQLOLEDB.1;Password=mypassword;User ID=sa;Initial Catalog=TPB;Data Source=THIERRY-HP\SQL2008" Any idea what's going wrong?

  Read the article

• Does fast typing influence fast programming?

  - by Lukasz Lew

  Many young programmers think that their bottleneck is typing speed. After some experience one realizes that it is not the case, you have to think much more than type. At some point my room-mate forced me to turn of the light (he sleeps during the night). I had to learn to touch type and I experienced an actual improvement in programming skill. The most surprising was that the improvement not due to sheer typing speed, but to a change in mindset. I'm less afraid now to try new things and refactor them later if they work well. It's like having a new tool in the bag. Have anyone of you had similar experience? Now I trained a touch typing a little with KTouch. I find auto-generate lessons the best. I can use this program to create new lessons out of text files but it's only verbatim training, not auto-generated based on a language model. Do you know any touch typing program that allows creation of custom, but randomized lessons?

  Read the article

• Split Tunnel VPN using incorrect Tunnel

  - by Brian Schmeltz

  Our company has a handful of field offices that have recently been setup with a regular internet connection after we removed the T1 and router that connected them directly to our network. Now, when the users are in the office, they log in to the VPN to be able to connect to the network. For the sake of them being able to print and scan from the local multi-function we have setup a split tunnel VPN. We currently have about 15-20 users using this setup around the country without any problems. Recently one of our users started having problems accessing internal programs/sites when connecting from both home and the office. There are three other users in the same office and they do not have this problem. I assumed that it was something with the computer and went ahead and replaced it with another of the same model. The computer worked fine in our home office; however, when the user received it, she had the exact same problem both at home and in the field office. Thinking it may be a NIC driver issue I sent her another computer, this time a different model, same problem occurred. If I update the host file to point to the correct paths, things will work, and if I connect via a normal VPN connection everything works, but the user cannot scan or print - which is a problem. Have tried to find ways to create another tunnel on a normal VPN and have tried to find ways to force the correct tunnel on the split tunnel VPN. It appears that there is something related to the ISP because if I connect to Comcast or Verizon it is fine but once she connects to Insite then she has problems. I have been unable to get any support from Insite as they don't feel the issue is with them. We use a Nortel VPN client. Any thoughts or ideas would be appreciated.

  Read the article

• Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

  - by D.S.

  I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

  Read the article

• Why does "commit" appear in the mysql slow query log?

  - by Tom

  In our MySQL slow query logs I often see lines that just say "COMMIT". What causes a commit to take time? Another way to ask this question is: "How can I reproduce getting a slow commit; statement with some test queries?" From my investigation so far I have found that if there is a slow query within a transaction, then it is the slow query that gets output into the slow log, not the commit itself. Testing In mysql command line client: mysql begin; Query OK, 0 rows affected (0.00 sec) mysql UPDATE members SET myfield=benchmark(9999999, md5('This is to slow down the update')) WHERE id = 21560; Query OK, 0 rows affected (2.32 sec) Rows matched: 1 Changed: 0 Warnings: 0 At this point (before the commit) the UPDATE is already in the slow log. mysql commit; Query OK, 0 rows affected (0.01 sec) The commit happens fast, it never appeared in the slow log. I also tried a UPDATE which changes a large amount of data but again it was the UPDATE that was slow not the COMMIT. However, I can reproduce a slow ROLLBACK that takes 46s and gets output to the slow log: mysql begin; Query OK, 0 rows affected (0.00 sec) mysql UPDATE members SET myfield=CONCAT(myfield,'TEST'); Query OK, 481446 rows affected (53.31 sec) Rows matched: 481446 Changed: 481446 Warnings: 0 mysql rollback; Query OK, 0 rows affected (46.09 sec) I understand why rollback has a lot of work to do and therefore takes some time. But I'm still struggling to understand the COMMIT situation - i.e. why it might take a while.

  Read the article

• vmware vcenter 5.1 installation with FQDN error

  - by CSG

  I'm trying to install vCenter 5.1 on a windows 2012 dedicated (with SQL express standalone) During the installation of the Single Sign On module i've a warning "the fully qualified domain name cannot be resolved with nslookup. if you continue the installation some features might not work correctly. for detailed requiments see the installation and setup guide" The only indication that i've found are about the reverse zone dns resolution.. and this works! i've verified that the dns works properly with nslookup C:\Users\admin>nslookup srv6.mydomain.local Server: srv2.mydomain.local Address: 172.25.4.22 Nome: srv6.mydomain.local Address: 172.25.1.26 C:\Users\admin>nslookup 172.25.1.26 Server: srv2.mydomain.local Address: 172.25.4.22 Nome: srv6.mydomain.local Address: 172.25.1.26 (all ip are right: I've the vCenter=srv6 and DC+DNS=srv2 on different vlan) i've tryed to force the resolution of the ip changing the [..]\drivers\etc\hosts file i've disabled the IPv6 support i've used all combination with domain prefixes (explicit, by dhcp, undefined..) i've disabled all antivirus/firewall (kaspersky end point 10) is this a bug of vcenter 5.1.0-1065152 ? have you got any suggestions for me?

  Read the article

• Block protect (Keep last line of paragraph with next paragraph)

  - by Ed Cottrell

  Is there a way to force Microsoft Word 2010 to keep the last line of a paragraph with the next paragraph? An example of when this is relevant is when starting a block quote; it doesn't look good to have the block quote start at the top of a new page, particularly when it's introduced by a partial sentence, like this: "Lorem ipsum" is sample text widely used in the publishing industry, as the text has spacing roughly similar to that of English and therefore looks "normal" but unintelligible to an English reader's eye, allowing the reader to focus on design elements. It begins, Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam rhoncus laoreet risus, quis congue leo viverra congue. Suspendisse magna massa, viverra imperdiet est eu, ultrices volutpat lectus. Sed pulvinar est id risus lobortis venenatis. There shouldn't be a page break after "begins," because it looks like the sentence ends abruptly. "Keep lines together" won't work, because by definition we're talking about two paragraphs. "Keep with next" won't work if the first paragraph is larger than a couple of lines, because then you get an awkwardly large space at the bottom of a page. Manual line breaks obviously work, but only when the document is final, which is often less certain than it seems. I know WordPerfect has a feature called "block protect" that does this, but I have not found even an acceptable substitute in Word. I have played with style separators and hidden paragraph breaks, but to no avail. I would love a special character, kind of like the nonbreaking space or zero width optional space, that tells Word to move to the next page if the next paragraph would otherwise start the page. A macro would also be great, but I haven't been able to find a starting point (like how to detect where non-manual page breaks fall). Edit: It looks like "Keep with next" works this way in Word 2013, but I specifically need a fix that works in Word 2010.

  Read the article

• RemoteApp .rdp embed creds?

  - by Chris_K

  Windows 2008 R2 server running Remote Desktop Services (what we used to call Terminal Services back in the olden days). This server is the entry point into a hosted application -- you could call it Software as a Service I suppose. We have 3rd party clients connecting to use it. Using RemoteApp Manager to build RemoteApp .rdp shortcuts to distribute to client workstations. These workstations are not in the same domain as the RDS server. There is no trust relationship between domains (nor will there be). There is a tightly controlled site to site VPN between workstations and the RDS server, we're quite confident we have access to the server locked down. The remoteApp being run is an ERP application with its own authentication scheme. The issue? I'm trying to avoid the need to create AD logins for every end user when connecting to the RemoteApp server. In fact, since we're doing a remoteApp and they have to authenticate to that app, I'd rather just not prompt them at all for AD creds. I certainly don't want them caught up in managing AD passwords (and periodic expirations) for accounts they only use to get to their ERP login. However, I can't figure out how to embed AD creds in a RemoteApp .rdp file. I don't really want to turn off all authentication on the RDS server at that level. Any good options? My goal is to make this as seamless as possible for the end-users. Clarifying questions are welcome.

  Read the article

• Cooling for a small server room

  - by John Zwinck

  I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

  Read the article

• 500 error with deploying rails application via apache2+passenger

  - by user1633983

  I finally completed my own app, so the only work left is deploying the app. I'm using Ubuntu 10.04 and apache2(installed by apt-get), so I'm trying to deploy through passenger. I installed passenger gem like this: sudo gem install passenger rvmsudo passenger-install-apache2-module and I configured apache settings as what the installation message says. I added below lines in the middle of /etc/apache2/apache2.conf file. LoadModule passenger_module /home/admin/.rvm/gems/ruby-1.9.3-p194/gems/passenger-3.0.17/ext/apache2/mod_passenger.so PassengerRoot /home/admin/.rvm/gems/ruby-1.9.3-p194/gems/passenger-3.0.17 PassengerRuby /home/admin/.rvm/wrappers/ruby-1.9.3-p194/ruby and, I appended below lines in /etc/apache2/sites-available/default file. <VirtualHost *:80> ServerName localhost # !!! Be sure to point DocumentRoot to 'public'! DocumentRoot /home/admin/homepage/public <Directory /home/admin/homepage/public> # This relaxes Apache security settings. AllowOverride all # MultiViews must be turned off. Options -MultiViews </Directory> But when I restart the apache service and hit the address, 500 error occurs. At first, it was same 500 error but the 500 error page is from apache's, but when I reinstalled the libapache2-module-passenger, the 500 error page is changed to that from rails'. Because of rails' 500 error page(which is located at public/500.html), I think passenger module is properly connected with apache. What should I do to fix this problem? Do I need to configure something inside my app before deployment?

  Read the article

• Moving MySQL directory on an Amazon EC2 machine

  - by Traveling Tech Guy

  I'm trying to have MySQL point to a directory on an EBS volume I mounted on my EC2 machine. I took th following steps: Stopped MySQL (/etc/init.d/mysqld stop) - successful Created a MySQL directory on my volume, mounted on /vol (mkdir /vol/mysql) Copied the contents of /var/lib/mysql to /vol/mysql (cp -R /var/lib/mysql /vol/mysql) Chanded the owner and group of that directory to match the original (chown -R mysql:mysql /vol/mysql) - after this step, the 2 directories are identical. Edited the /etc/my.cnf file (commented 2 original lines): [mysqld] #datadir=/var/lib/mysql #socket=/var/lib/mysql/mysql.sock datadir=/vol/mysql socket=/vol/mysql/mysql.sock` Started MySQL (/etc/init.d/mysqld start) - FAILED The error file /var/log/mysqld.log contains the following lines: 100205 20:52:54 mysqld started 100205 20:52:54 InnoDB: Started; log sequence number 0 43665 100205 20:52:54 [Note] /usr/libexec/mysqld: ready for connections. Version: '5.0.45' socket: '/vol/mysql/mysql.sock' port: 3306 Source distribution No other errors are available. What am I doing wrong? Where can I find the error/s encountered by MySql? If I restore the original lines, MySQL starts, leading me to believe it may be a permissions issue - but permissions are the same for both directories? Thanks!

  Read the article

• Help setting up a secondary authoritative DNS server.

  - by GLB03

  We have three Authoritative DNS servers and three recursive/caching DNS servers on my campus. Authoritative servers DNS1- Windows 2003 DNS2- Old Red Hat ----- Replacing w/ newer version DNS3- Windows 2008 (I installed) Caching and Recursive resolvers servers Server1- Windows 2003 Server2- CentOS 5.2 (I installed) Server3- CentOS 5.3 (I installed) I am replacing DNS2 with a newer Red Hat version, but have no documentation on how it was implemented. I have setup caching and windows authoritative servers, but not a linux secondary authoritative server. I have a perl script from the original server that pulls data from our DNS1 server. We use DJBDNS and TinyDNS on our linux servers. Our Network Engineer says the DNS2 server I am replacing is an authoritative server that doesn't need to be caching, but the only instructions I see is for an Authoritative server that does caching as well. Can someone point me in the right directions. I thought I was on the right track with using these instructions but when I query my new dns server I get "No response from server", I have temporarily disabled iptables to eliminate it from being an issue. ps -aux | grep dns avahi 3493 0.0 0.2 2600 1272 ? Ss Apr24 0:05 avahi-daemon: running [newdns2.local] root 5254 0.0 0.1 3920 680 pts/0 R+ 09:56 0:00 grep dns root 6451 0.0 0.0 1528 308 ? S Apr29 0:00 supervise tinydns dnslog 6454 0.0 0.0 1540 308 ? S Apr29 0:00 multilog t ./main tinydns 9269 0.0 0.0 1652 308 ? S Apr29 0:00 /usr/local/bin/tinydns

  Read the article

• cPanel web servers mounting home partition to a NAS or SAN

  - by Scott

  I currently have 2 cPanel web servers that are little 1RU dual cpu quad core xeons. They have a lot of resources for processing and handling web requests, and never exceed more than 10% cpu usage. They also have plenty of RAM. The problem is though that they both have RAID 1 160Gb SAS hard disk drives in them that are 75% full, and growing by the day. I didnt think that the amount of disk usage would be so high, but due to the nature of the sites hosted, this has become an issue. The easy fix would be just to upgrade the hard drives to something bigger (probably not of the SAS variety), but I am thinking of keeping the current machines as "processing servers" and buying a central "storage server" with about 12TB of storage. The /home/ partition on each of the 1RU servers would be mounted to a NAS or SAN point on this central storage server. My questions are: - Has anyone got a cPanel setup where they mount /home/ to a NAS or SAN elsewhere? If so, can you provide details as to what you did and how it went :) - Any recommendations on networking? Is gigabit ethernet enough? Is TCP/IP going to be a noticable performance problem? Anyone used a TOE key? - Anyone benchmarked or had any performance issues with SAN over NAS? Any help greatly appreciated. Scott

  Read the article

• Problem building PHP extension module

  - by tixrus

  I'm trying to get GD into my PHP. So I compiled it, made php.ini point to it, restarted apache etc. But no GD. So in apache error log it says PHP Warning: PHP Startup: gd: Unable to initialize module\nModule compiled with module API=20060613\nPHP compiled with module API=20090115\nThese options need to match\n in Unknown on line 0 So a bit of googling says I should not use the phpize I have before configuring and making these. I should use a new one called phpize5. I surely don't have any such thing. Unless its packed up inside something else in my php5.3. distro. Where do you get it. In Ubuntu I could just run sudo apt-get install php-dev, (apparently) and it would just appear by magic. At least that's what the webpage said. Unfortunately I am running MacOSX version Leopard. How can I build this GD module so that it will match the API number in my PHP?

  Read the article

• How to re-join an AD2003 domain with Samba after deleting the machine account?

  - by Guss

  During some troubleshooting I deleted the machine account for a Linux server running samba from our AD 2003 domain. We are using Kerberos for authentication, and after I deleted the machine account I tried to join the domain again using net ads join -U Administrator But I keep getting Kerberos errors like these: [2009/08/18 16:14:36, 0] libads/kerberos.c:ads_kinit_password(228) kerberos_kinit_password [email protected] failed: Client not found in Kerberos database Failed to join domain: Improperly formed account name It appears as if samba remembers that it once had an account with the AD and keeps trying to reconnect to it, but I want to create a new account from scratch. I tried to delete all the .tdb files I could find as well as everything under /var/cache/samba but to no avail - it still behaves the same. I also tried to create the machine account on the AD side, but then I get a similar error when I try to join, about failure to authenticate with the machine account - it looks like samba tries the previous machine account password and I don't know how to reset it, or even if I could figure out what samba uses - how to set it in the AD. Any help would be greatly appreciated, as at this point the only thing I can think about is to reformat and reinstall the machine, and I would really REALLY love to not do that. Thanks in advance.

  Read the article

• Setting up subdomain to respond on :443 with apache2

  - by compucuke

  I read through some guides on this and I believe it is possible to have apache respond to a subdomain through ssl. I have domain.com responding on 80 and I do not need domain.com responding on 443. Rather, the only use I have for ssl is for the subdomain sub.domain.com. So my site should be http://domain.com http://www.domain.com https://sub.domain.com https://www.sub.domain.com My CNAME records are as follows sub.domain.com xxx.xx.xx.xxx *.sub.domain.com xxx.xx.xx.xxx The A record exists but should not matter for the example. I set up a separate config file in sites-enabled for sub.domain.com NameVirtualHost xxx.xx.xx.xxx:443 <VirtualHost xxx.xx.xx.xxx:443> SSLEngine on SSLStrictSNIVHostCheck on SSLProtocol -ALL +SSLv3 +TLSv1 SSLCipherSuite ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:-MEDIUM ServerAlias sub.domain.com DocumentRoot /usr/local/www/ssl/documents/ SSLCertificateFile /root/sub.domain.com.crt SSLCertificateKeyFile /root/sub.domain.com.key Alias /robots.txt /usr/local/www/ssl/documents/robots.txt Alias /favicon.ico /usr/local/www/ssl/documents/favicon.ico Alias /js/libs /usr/local/www/ssl/documents/js/libs Alias /media/ /usr/local/www/documents/media/ Alias /img/ /usr/local/www/ssl/documents/img/ Alias /css/ /usr/local/www/ssl/documents/css/ <Directory /usr/local/www/ssl/documents/> Order allow,deny Allow from all </Directory> WSGIDaemonProcess sub.domain.com processes=2 threads=7 display-name=%{GROUP} WSGIProcessGroup sub.domain.com WSGIScriptAlias / /usr/local/www/wsgi-scripts/script.wsgi <Directory /usr/local/www/wsgi-scripts> Order allow,deny Allow from all </Directory> </VirtualHost> Now, it is important to mention that https://domain.com responds with what I have running from script.wsgi above instead of on https://sub.domain.com. It does not respond to sub.domain.com. checking https://sub.domain.com causes a 105 error. This is a DNS error but I am convinced the DNS does not have a problem with the CNAME records, they just point to my IP. Am I doing something that Apache can not do?

  Read the article

• How to change controller numbering/enumeration in Solaris 10?

  - by Jim

  After moving a Solaris 10 server to a new machine, the rpool disk is now c1t0d0. We have some third party applications hard coded for c0t0d0. How can I change the controller enumeration on this machine? There is no longer a c0. I've tried rebuilding the /etc/path_to_inst, but the instance numbers don't seem to match up with the controller numbers. Also, it's not clear if i86pc platforms use this file. I've tried devfsadm -C to clear the dangling links, but I'm not sure how to cause devfsadm to start numbering from 0 again (or force certain devices in the tree to a specific controller number). Next I am going to try to create the symlinks manually in /dev/dsk and rdsk to point to the correct /devices. I feel like I am going way off path here. Any suggestions? Thanks Update: This is on virtual ESXi hardware with an additional pass-through HBA. There is no controller 0 on the machine, that is for sure. devfsadm -C cleans up all the c0 device symlinks but keeps the already linked controllers at their current ids.

  Read the article

• Cannot send email outside of network using Postfix

  - by infmz

  I've set up an Ubuntu server with Request Tracker following this guide (the section about inbound mail would be relevant). However, while I'm able to send mail to other users within the network/domain, I cannot seem to reach beyond - such as my personal accounts etc. Now I have no idea what is causing this, I thought that all it takes is for the system to fetch mail through our exchange server and be able to deliver in the same way. However, that hasn't been the case. I have found another server setup in a similar fashion (CentOS 5, Request Tracker but using Sendmail), however it is a dated server and whoever's built it has kindly left no documentation on how it works, making it a pain to use that as a reference system! :) At one point, I was told I need to set up a relay between the local server's email add and our AD server but this didn't seem to work. Sorry, I know next to nothing about mailservers, my colleagues nothing about Linux so it's a hard one for me. Thank you! EDIT: Result of postconf -N with details masked =) alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = myhost.mydomain.com, localhost.mydomain.com, , localhost myhostname = myhost.mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = EXCHANGE IP smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes Sample log message: Sep 4 12:32:05 theedgesupport postfix/smtp[9152]: 2147B200B99: to=<[email protected]>, relay= RELAY IP :25, delay=0.1, delays=0.05/0/0/0.04, dsn=5.7.1, status=bounced (host HOST IP said: 550 5.7.1 Unable to relay for [email protected] (in reply to RCPT TO command))

  Read the article

• DNS server not working?

  - by Behrooz A

  I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

  Read the article

• Debian network bridge configuration - /etc/network/interfaces

  - by Mathias

  I'm running a Lenny Xen dom0 hosting multiple virtual machines in a routed IP setup. To get an additional private subnet, I created the bridge xenbr0 in the dom0 with the following commands: brctl addbr xenbr0 ifconfig xenbr0 10.0.0.1 netmask 255.255.255.0 ifconfig xenbr0 up This works as expected, and domU interfaces are added to the bridge by Xen on VM start. My only problem is: how the heck do i specify this configuration in /etc/network/interfaces that it remains permanent and the bridge is available after a reboot? I tried the following config as found on a lot of tutorials: auto xenbr0 iface xenbr0 inet static address 10.0.0.1 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 bridge_stp no I get 2 different errors, depending on if the bridge already exists or not. If it doesn't exist: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). SIOCSIFADDR: No such device xenbr0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device xenbr0: ERROR while getting interface flags: No such device xenbr0: ERROR while getting interface flags: No such device Failed to bring up xenbr0. done. And if it exists: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.000000000000 no root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). RTNETLINK answers: File exists Failed to bring up xenbr0. done. Could anyone point me in the right direction please? The bridge works fine when created manually, i just need the right config file entries. The most tutorials I found add some devices to the bridge in the config, is that maybe the problem why it is not working? I don't have any interfaces I want to add to the bridge on creation as they get added later on VM start... Thanks, Mathias

  Read the article

• Computer causing WiFi interference?

  - by Mannimarco

  I came back from college and brought my desktop computer. Family recently switched to Verizon FIOS and got a new router because of it. Unfortunately, my connection to the new wifi network is awful, with the download speeds (tested through speedtest.net) fluctuating wildly and often dropping below 1.5 Mbps. A laptop in the same room gets 20 Mbps. I've tried a new wireless card, thinking that mine got damaged in the move home but no luck. Here's where it gets weird: if I place the laptop near the computer, the laptop's download speeds often suffer greatly. Pulling the laptop away always fixes this. So now I'm under the impression that there's something in the computer (which I built a year ago and has had 0 issues up to this point) is causing an insane amount of wireless interference. Also bizarre: the upload speeds seem unaffected by this problem. On the laptop and desktop, upload speeds are generally around 5 Mpbs. Any ideas as to what could be causing this and how to test said theories would be fantastic.

  Read the article

• Split Tunnel VPN using incorrect Tunnel

  - by Brian Schmeltz

  Our company has a handful of field offices that have recently been setup with a regular internet connection after we removed the T1 and router that connected them directly to our network. Now, when the users are in the office, they log in to the VPN to be able to connect to the network. For the sake of them being able to print and scan from the local multi-function we have setup a split tunnel VPN. We currently have about 15-20 users using this setup around the country without any problems. Recently one of our users started having problems accessing internal programs/sites when connecting from both home and the office. There are three other users in the same office and they do not have this problem. I assumed that it was something with the computer and went ahead and replaced it with another of the same model. The computer worked fine in our home office; however, when the user received it, she had the exact same problem both at home and in the field office. Thinking it may be a NIC driver issue I sent her another computer, this time a different model, same problem occurred. If I update the host file to point to the correct paths, things will work, and if I connect via a normal VPN connection everything works, but the user cannot scan or print - which is a problem. Have tried to find ways to create another tunnel on a normal VPN and have tried to find ways to force the correct tunnel on the split tunnel VPN. It appears that there is something related to the ISP because if I connect to Comcast or Verizon it is fine but once she connects to Insite then she has problems. I have been unable to get any support from Insite as they don't feel the issue is with them. We use a Nortel VPN client. Any thoughts or ideas would be appreciated.

  Read the article

< Previous Page | 621 622 623 624 625 626 627 628 629 630 631 632  | Next Page >