point of sale - Page 628

Sun T5120: Memory issue with 8GB DIMMs, "Unsupported memory configuration"

- by watain

Read the article

How to enable Ipv6 on my ubunutu 11.04 virtual machine

- by liv2hak

I have installed 3 VM's on my PC.(Ubuntu 11.04).I want to setup an IPV6 network to review and test some of the IPV6 tools like NDPMonitor.(monitors ICMP messages of Neighbour Discovery Protocol.) IP v6 addresses are as follows. linux_router - fe80::a00:27ff:fed5:f7e9/64 labhack1 - fe80::a00:27ff:fed2:8bd1/64 labhack2 - fe80::a00:27ff:fed7:2f2d/64 The below commands have been run on both linux_router and labhack1. sudo ip r a 2001:468:181:f100::/64 dev eth0 sudo vim /etc/radvd.conf /file looks like below./ interface eth0 { AdvSendAdvert on; /*means that we are sending out advertisments.*/ MinRtrAdvInterval 5; /*these options control how often advertisments are sent*/ MaxRtrAdvInterval 15; /*these are not mandatory but valueable settings.*/ prefix fe80::a00:27ff::/64 { AdvOnLink on; /*Says to the host everyone sharing this prefix is on the sam local link as you.*/ AdvAutonomous on; /*Says to a host: "Use this prefix to autoconfigure your address"*/ }; }; sudo sysctl -w net.ipv6.conf.all.forwarding=1 I try to do a ping6 -I eth0 fe80::a00:27ff:fed5:f7e9 I get Destination unreachable: Address unreachable.I am not sure what I am doing wrong here.I am a beginner at linux administration.Basically I think I am missing whatever is analogous to physically connecting VM's.Any help that would point me in the right direction would be greatly appreciated.

Read the article

ADO 2.8, VMWare and SQL Server - sudden bulk dropped connections

- by CodeByMoonlight

We have an overworked server currently running a single SQL Server 2000 instance on physical hardware, and about 40 different apps interact with it on a daily basis. Last year, the RAID controller failed and we had no spare, so IT Support hurriedly migrated it overnight to a copy running on a VMWare Server. While it was on that server everything ran much quicker due to it being a big improvement in spec. However, the biggest app using it had occasional serious errors which never occurred on physical hardware. Specifically, several times a week it would disconnect batches of users - anywhere from just ten to hundreds at once, and all at the same time. It didn't affect any particular users or PCs or offices - all were affected equally. The only common thing was the app, which is a VB6 app using ADO 2.8 to connect. The other apps connecting to that virtualised instance of SQL Server seemingly had no problems, although they were (and are) responsible for only a tiny fraction of the work involving this server. The upshot is that after about two weeks of loving the speed and hating the random mass disconnections (which we were never able to find a cause for), we sadly took the decision to return to physical hardware and the disconnections vanished. Now we've reached the point where the old server just can't handle all that's being asked of it, and we're intending to migrate everything to 2 or more other servers. The snag is that there's a good chance they'll have to be virtual ones again. Given what happened last time, I'm trying to find out what possible reasons there could be for these mass disconnections. We were running VMWare ESX, but the network is Novell-based. Also, the server had a linked server setup to connect to an Informix server using a known-to-be-buggy ODBC driver, and this is used throughout the day. Any ideas on the cause(s)?

Read the article

Windows 7 Blank Screen on Boot / Login

- by Greg

I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

Read the article

Need to Remove Exchange 2003 Server That Crashed During Transition to 2010

- by ThaKidd

As the title stated, we were running an Exchange 2003 server that we knew was going down soon so we purchased a second server and installed Exchange 2010 into the AD. We managed to move all of the mailboxes off of 2003 and also managed to get the Offline Address Book setup on 2010. At this point the 2003 server bit the dust and will no longer boot. Therefore we were unable to properly uninstall Exchange and remove the last 2003 server so it still exists in AD. As far as the clients are concerned, everything is working properly. However, when I run the Microsoft Exchange Profile Analyzer, I still see the old server and its Administrative Group. I am going to guess that since the old server is showing up in AD, I will not be able to raise Exchange or AD functionality (as the 2003 server was also the only AD DC) levels. I have forced the 2003 DC out of AD so that is no longer an issue. Old Setup: Windows 2003 Server Enterprise & Exchange 2003 Standard New Setup: Windows 2010 Server Enterprise & Exchange 2010 Standard Two Questions: How do you go about manually forcing the 2003 server and its administrative group out of AD? When that is finished, where do you raise the Exchange mode (can't find this for the life of me)?

Read the article

sysctl.conf not running on boot

- by Brian

At what point is sysctl.conf supposed to be read during boot, and why might it not be running? I have the following settings which are not being applied when I reboot: net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 fs.nfs.nlm_udpport = 32768 fs.nfs.nlm_tcpport = 32768 The first section is needed for KVM bridging, and the second is to run the NFS lock manager on a known port. However, after booting, these values have not taken effect. If I run sysctl -p, then they do. This wouldn't be a huge issue, except that I can't figure out how to restart the lock manager without rebooting. I would really like to know why sysctl.conf isn't working at boot, but I'd settle for just being able to restart the lock manager. This is on Ubuntu server 10.04.2, kernel 2.6.32-31-server. I know some daemons check the permissions on their config files and refuse to work if they're too permissive, but sysctl.conf is 644 root:root, which I'm pretty sure is the default.

Read the article

Use Mac OS X Server As Development Environment

- by macinjosh

I've installed Mac OS X Server 10.6.3 on my laptop to use as my normal OS. I do a lot of web development and thought it would be handy to run OS X Server so I could more easily manage my local development environment (Apache Virtual Hosts, Hostnames for each local site, etc). I'm really enjoying the new setup except for one problem. DNS. My ideal situation would be to add a site (some-site.local) in the Web Service and then go to the DNS Service and add a primary record for the new site. I actually got this working at one point but after a reboot it stopped working! The records look the same as they did before the reboot but the site doesn't come up in Safari. Here is a list of my needs: Need to be able to add new domains at a whim Domains always map to a site on the same box's Web Service Local & External IPs often change It would nice if it worked on any network (i.e. WiFi at the airport or coffee shop) Sites only need to be accessible locally Configuration should stay put even after rebooting I've done some googling and used this as a bit of guide. In the past I've used MAMP and then just a local Apache/PHP/MySQL install with a manually managed hosts file. I'd rather not go back.

Read the article

Amazon VPC NAT not working

- by rpkelly

I'm trying to create a NAT instance for my VPC to allow instances on private subnets connect to the internet (most importantly, S3). I tried following the instructions here: http://docs.amazonwebservices.com/AmazonVPC/2011-07-15/UserGuide/index.html?VPC_NAT_Instance.html . Unfortunately, the instances in the private subnet (call it 10.10.2.0/24) cannot reach the internet. I have done the following: Create a NAT instance (Amazon's ami-vpc-nat-1.0.0-beta.i386-ebs (ami-d8699bb1)) in public subnet (call it 10.10.1.0/24). Changed "Source / Dest Check" to disabled. Created a new entry in the default routing table (which is used by 10.10.2.0/24) and had it point to the ID of the newly created instance. Associated an Elastic IP address with the NAT instance. Allowed all outbound traffic on the security group of the NAT instance. Ensured that all traffic could pass between the two subnets. I've tried also doing this with an existing instance using iptables, but had no luck. And I have verified that sys.net.ipv4.ip_forward is 1, just in case anyone was wondering. And I still have no internet connectivity from the instances on 10.10.2.0/24. Does anyone have any suggestions?

Read the article

How to set up Zabbix to monitor SQL Server Failover Active-Passive Cluster?

- by Sebastian Zaklada

It should be simple, so it is just most likely my approach being totally off and someone will hopefully prod me into the right direction. We have a Zabbix 2.0.3 server instance set up monitoring a bunch of different servers, but now we need to set it up to monitor and notify any alerts in regards to the SQL Server 2008 R2 Failover Active-Passive cluster. Essentially, this is a 2 servers cluster, when only one of its nodes can be "active" at a given time, serving all SQL Server related requests, while the other server just "sleeps" and from the point of anyone logged on on that server - has all of the SQL Server related services in stopped state. We have tried setting up Zabbix agents on both servers, using SQL Server 2005 templates (we could not find any 2008 specific ones and the 2005 ones always seemed to be working just fine for monitoring 2008 R2 instances) and configuring Zabbix server for both of the servers, but we end up having constant alerts for the server being currently the passive one in the cluster. We have been able to look up various methods of actually monitoring the failover, but we have not been able to find any guidance in regards to how to instruct Zabbix, that in this particular case, only one of the servers in the group is expected to be in the online state, while the other can be just discarded and should not raise any alerts. I hope I made myself clear. Thanks for any guidance. I am out of ideas.

Read the article

Setting up Red Hat Enterprise Linux Server as a mail exchange server

- by Syedur

I am a Unix/Linux/Windows Server noob. So, keep that in mind before you throw your stones at my glass house. :P I have a Windows Server 2008 R2 machine that's acting as domain controller, Server A. It's also running a DNS server. I have a Red Hat Enterprise Linux Server 5.3, Server B that is intended for mail server. In order for the mail delivery to happen, I understand that I have to set an MX record on Server A and point it to Server B. Well, I did. I manually added a host name on Server A and pointed to Server B's IP address. Then I added an MX record and pointed it to the host name. That didn't do the trick. After taking the above steps, I used the "dig" command on Server B to lookup the MX record coming back from Server A and it wasn't what I was expecting. What am I doing wrong here? I have noticed that... my Windows machines that are joined to the domain (Server A) are listed under the host names. The machines that are not joined to the domain are not list. This is fine, I am not worried about this. What does concern me, do I have to join the Server B to domain in order for Server A to recognize as a valid host and forward the MX properly? If so, some simple steps on how to join Server B to the domain would also help.

Read the article

Some URLs fail to load on Windows web portal

- by jpolache

I’m working in a large data center and have been assigned to troubleshoot and issue with a windows (IIS) web server that acts as a portal for a customer of the data center. This portal server is on a DMZ at the local data center. I don’t have access to the portal desktop and am relying on an off-site administrator to work with me to do testing and report the condition of the portal. He tells me there are no software firewalls or other filtering configured. While most of the remote web pages work fine, several of the URSs the portal is suppose to serve up fail to load. I had wireshark installed on the portal system and had a capture taken of one of the failures. I used IE to access one of the remote web servers at issue. I could see the TCP SYN-ACK coming back from the remote server, but after several HTTP GETs fail to get a response the portal server sends a reset. The webmaster of the remote web server assures me that no sites are being blocked. I had a capture taken outside the local firewall, so there should be no issue there. Another tech set up a laptop and used the IP address of the portal (we took the portal off-line for the test). The laptop loads the URL as expected. I tried having Firefox loaded to make sure that the HTTP GET was not mal-formed. Same failure as with IE. So, it seems it is not the remote web server or the network, because there was no problem with the laptop. At this point, I’m not sure what other questions to ask or tests to do.

Read the article

Converting DisplayPort and/or HDMI to DVI-D?

- by Jeff Atwood

Newer Radeon video cards come with four ports standard: DVI (x2) HDMI DisplayPort If I want to run three 24" monitors, all of which are DVI only, from this video card -- is it possible to convert either the HDMI or DisplayPort to DVI? If so, how? And which one is easier/cheaper to convert? I did a little research and it looks like there isn't a simple "dongle" method. I found this DisplayPort to DVI-D Dual Link Adapter but it's $120; almost cheaper to buy a new monitor that supports HDMI or DisplayPort inputs at that point! There's also a HDMI to DVI-D adapter at Monoprice but I'm not sure it will work, either. AnandTech seems to imply that you do need the DisplayPort-to-DVI: The only catch to this specific port layout is that the card still only has enough TMDS transmitters for two ports. So you can use 2x DVI or 1x DVI + HDMI, but not 2x DVI + HDMI. For 3 DVI-derived ports, you will need an active DisplayPort-to-DVI adapter.

Read the article

Database problem with MS JET

- by Zimmy-DUB-Zongy-Zong-DUBBY

I am migrating a bunch of sites which each use an Access database (or whatever an MDB file is). If I try to load the site, I get the following error: Microsoft OLE DB Provider for SQL Server error '80004005' [DBNETLIB][ConnectionOpen (Connect()).]SQL Server does not exist or access denied If I rename the MDB file, I get a complaint that the file does not exist, which makes sense. If the file is named correctly, the site tries to load for about 30 seconds or so, and then just fails with the above message. During this waiting period, I can see a lock file being created (and then at some point removed). The MDB file and it's parent dir have full permissions granted to all users. Given that the lock file is successfully created and removed, I don't think that this is a "real" permission issue. The OS is Windows Server 2003 SP2. I am not sure about much more detail on it's config wrt Access databases. I also don't know what version it is expected to be. VB code in question: set oConn=server.createobject("adodb.connection") DSNtemp="Provider=Microsoft.Jet.OLEDB.4.0;Data Source=D:\fullPathGoesHere\db\sitedb.mdb" oConn.Open DSNtemp

Read the article

Why do I get a DegradedArray event with mdadm

- by azera

Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

Read the article

How do you setup FTP with IIS Manager Users in an NLB environment with shared IIS configs?

- by William Jens

I've setup a 2 node NLB cluster and used the following to share IIS configs between them. http://blogs.technet.com/b/meamcs/archive/2012/05/30/configuring-iis-7-5-shared-configuration.aspx The IIS configs and content is located on a network share via a UNC path. This works - updating IIS settings on one node, is visible in another node and my website works on the individual nodes and the cluster as whole. I'm able to setup an FTP site and successfully connect with my Windows login. However, I want to use IIS Manager Authentication as defined in: http://www.iis.net/learn/publish/using-the-ftp-service/configure-ftp-with-iis-manager-authentication-in-iis-7 I've tried using "Network Service" with the FTP COM object as well as a dedicated user account that exists on all three hosts, but every time I try to login with an IIS user I get something like the following: IISWMSVC_AUTHENTICATION_UNABLE_TO_READ_CONFIG An unexpected error occurred while retrieving the authentication information. Exception:System.Runtime.InteropServices.COMException (0x8007052E): Filename: Error: at Microsoft.Web.Administration.Interop.AppHostWritableAdminManager.GetAdminSection(String bstrSectionName, String bstrSectionPath) at Microsoft.Web.Administration.Configuration.GetSectionInternal(ConfigurationSection section, String sectionPath, String locationPath) at Microsoft.Web.Management.Server.ConfigurationAuthenticationProvider.GetSection(ServerManager serverManager) Process:dllhost User=NT AUTHORITY\NETWORK SERVICE Can anyone point me in the right direction here?

Read the article

Problem with PXE boot

- by user70523

I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

Read the article

Messed up USB stick doesn't show in blkid

- by Felix

I was playing around with a USB stick (booting archlinux with qemu off of it and trying to perform an installation on the same stick at the same time -- brave, I know, but I was just messing around). Now, after failing to boot and install at the same time, it seems I have sort of messed up my stick. What I think happened is that I used cfdisk to wipe everything on it and create one big partition, but formatting it then failed, so now there's a big partition with no filesystem. Just to make it clear: I'm not worried for my stick, I know I can recover it at any point. What I find intriguing is that after plugging the stick into my computer (using Ubuntu), there's no (terminal) way to find out what block device (/dev/sdx) it has associated. The only way I could determine that was with GParted: But blkid shows the following: /dev/sda1: UUID="12F695CFF695B387" LABEL="System Reserved" TYPE="ntfs" /dev/sda2: UUID="A0BAA6EABAA6BC62" TYPE="ntfs" /dev/sdb1: UUID="546aec8b-9ad6-4571-b07a-adba63e25820" TYPE="ext4" /dev/sdb2: UUID="2a8b82d8-6c6e-4053-a446-bab970d93d7c" TYPE="swap" /dev/sdb3: UUID="7cbede7d-c930-4e59-9d1b-01f2d79bd092" TYPE="ext4" No trace of /dev/sdc. My question is: if I didn't have a graphical interface (to use GParted), how would I have known which block device is my stick?

Read the article

When pointing to new DNS servers is there any chance of E-mails being lost if the old E-mail hosting service is still up?

- by LaserBeak

I am changing webhosts and will be using the new hosts mail servers instead of the old ones. I have created all the correctly named mailboxes on the new service but have also not yet cut ties with the old webhost. I am expecting that even if the new DNS values which point to the new hosts DNS servers and respective SOA\zone file with the new MX values have not yet propagated and an E-mail is directed at the old hosts mail servers as per the mx records in the SOA\zone records which the old hosting provider holds, the E-mail would still come through to the mailbox that's on the old host providers mail servers. So I am just trying to reaffirm if I got this right and it's essentially impossible for me to loose an E-mail since it will hit either the old hosts mail servers or the new ones ? Also is it possible to configure the same E-mail account to check and collect mail from different mail servers by entering multiple pop3 addresses ? And if I choose to keep the old web hosts mail hosting services as a backup by specifying the mx records for it with a lower priority in the SOA records hosted by the new webhost, is it possible to have any incoming E-mails sent to both servers by the mail daemon so I have two copies? Or is my only option having the primary mail server forward the E-mail somehow to the old mailserver ?

Read the article

Toshiba External Hard Drive freezes computer

- by Ephraim

I bought a Toshiba Canvio Basics E05A032BAU2XK Portable External 320GB 2.5 Hard Drive: My computer has two Os's on it Win7 and Win XP. I need both. The main one I use is XP. When booting my computer in any OS the computer and hard drive work fine. The same holds true for plugging in the hard drive while running Win7. However, when running WinXP, if the hard drive gets plugged in the computer freezes(my main point is that the HD is portable so it is essential that it does not do this, as I said I usually run XP). After reading some online forums I was informed that there is a compatibility issue with the newest version of Eset Smart Security(I still don't understand this because it works fine in Win7 or when connected on boot...). I disabled the AV and plugged in the HD... Walla! The comnputer did not freeze. However the disk is not recognized in explorer or disk management. In device manager I removed the device and did a scan and installation of device failed. It pretty much sounds like a driver issue but I cannot find any drivers for this HD. In fact, Toshiba claims that there are no downloadable drivers for it and that XP should take care of the drivers itself. What to do? As far as I can tell, all other USB devices work just fine on both OS. Please Help!

Read the article

Multiple Internet connections, multiple networks and split access in Linux

- by Swapneel Patnekar

I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

Read the article

Outlook 2007/2010 autodiscovering old Exchange info

- by Dan

I currently have an Exchange setup as follows: two Exchange 2003 servers clustered together set up as the current mailbox stores, one Exchange 2003 setup as a frontend, one Exchange 2007 set up as a frontend (was set up for testing by my predecessor, never really used intentionally), and now four Exchange 2010 servers - two mailboxes in a DAG and two with Hub/CAS. Everything seems to be working fine with one exception - Outlook 2007/2010 clients are still autodiscovering the test 2007 frontend and not the 2010 CAS array. I know this because there's an expired cert on the 2007 box so the client displays a cert error when you attempt to autocreate the outlook profile. From what I've read, there is an SCP (Service Connection Point) in AD that is pointing to the old server and it is getting returned first, causing Outlook to try it first. How can I prevent Outlook from even attempting to connect to this 2007 box from now on? http://www.msexchange.org/articles_tutorials/exchange-server-2010/management-administration/exchange-autodiscover.html When Outlook 2007 is installed on a domain joined workstation then the Outlook client will query Active Directory for the Autodiscover information. Active Directory will return a list of SCP’s and the Outlook client will automatically select the first SCP in this list. Using the information found in the SCP the Outlook client will contact the Client Access Server for its configuration information and the Outlook client will be configured automatically.

Read the article

Will just a couple of thermal "trip" shutdowns typically damage a CPU?

- by T.J. Crowder

The short version If a CPU gets so hot that the system turns itself off because of a thermal trip signal just a couple of times, is it likely that the CPU will be damaged? Or does the trip do its job, turning it off before the CPU gets damaged? (This is with all default settings in the BIOS; I haven't raised any temp thresholds or overclocked anything.) The longer version I just got this Intel Atom D510-based fanless system, installed a 2.5" mobile SATA drive and two 2GB PC2-6400s, closed it up, and having checked everything was recognized in the BIOS, set about installing Ubuntu. After a couple of false starts related, I think, to the external DVD drive I was using, I got the install happily running along. About three-fourths or so of the way through the install, having been running less than an hour, the machine turned itself off. I was actually out of the room at the time, but when I came back and turned it back on, it said it had shut down due to a thermal event. I went into the BIOS and saw that (at that point, having just been turned back on after a couple of minutes off), it was running 87C. As near as I can tell from Intel's docs (PDF here), the max "junction" temperature for the CPU is 100C and it will raise a THERMTRIP signal at 125C. Yowsa. Presumably there will be some back-and-forth with the vendor on this, I'm just wondering whether letting it get that hot a couple of times is likely to end up damaging it.

Read the article

How to serve Rails application with Passenger/Apache without domain name?

- by grifaton

I am trying to serve a Rails application using Passenger and Apache on a Ubuntu server. The Passenger installation instructions say I should add the following to my Apache configuration file - I assume this is /etc/apache2/httpd.conf. <VirtualHost *:80> ServerName www.yourhost.com DocumentRoot /somewhere/public # <-- be sure to point to 'public'! <Directory /somewhere/public> AllowOverride all # <-- relax Apache security settings Options -MultiViews # <-- MultiViews must be turned off </Directory> </VirtualHost> However, I do not yet have a domain pointing at my server, so I'm not sure what I should put for the ServerName parameter. I have tried the IP address, but when I do that, restarting Apache gives apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Sun Jan 17 12:49:26 2010] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Sun Jan 17 12:49:36 2010] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results and pointing the browser at the IP address gives a 500 Internal Server Error. The closest I have got to something sensible is with <VirtualHost efate:80> ServerName efate DocumentRoot /root/jpf/public <Directory /root/jpf/public> AllowOverride all Options -MultiViews </Directory> </VirtualHost> where "efate" is my server's host name. But now pointing my browser at the server's IP address just gives a page saying "It works!" - presumably this is a default page, but I'm not sure where this is being served from. I might be wrong in thinking that the reason I have been unable to get this to work is related to not having a domain name. This is the first time I have used Apache directly - any help would be most gratefully received!

Read the article

Is this a File Header / Magic Number?

- by Hammer Bro.

I've got 120,000 files (way more, actually; this is just an arbitrary subset) of an unknown type. Linux file does not identify them (not that they're necessarily Linux files), nor do any other methods I've tried. There are only two hints about them that I currently have. One is that I suspect some compression is employed -- I have metadata that claims the file sizes are always some amount larger than what I observe. The other is that in 100,000 of these files, the first 16 bytes are always: ff ee ee dd 00 00 00 00 01 00 00 00 00 00 00 00 That really looks like a file header/magic number to me, but I just can't place it. Does anyone know what kind of files this would indicate? Alternatively, can anyone convince me that these suspiciously common bytes certainly do not indicate a specific file type? UPDATE I don't know the exact reverse-engineering details, but most of the files in our case are zips after the first 29(? or so) bytes are ignored. So in practice the problem is solved (we know how to process the files) but in theory the question is still unanswered -- I don't know which application routinely prepends about 29 bytes to its zips. [I'm not sure if I should leave the question open or not at this point.]

Read the article

Apt pin and self hosted apt repo

- by Hamish Downer

We have our own apt/deb repository with a handful of packages where we want to control the version. Crucially this includes puppet, which can be sensitive to versions being different. I want our desktops to only get puppet from our repository, but also for people to be able to add their own PPAs, enable backports etc. The current problem we have is backports on Ubuntu Lucid. Some important lines from /etc/apt/sources.list: deb http://gb.archive.ubuntu.com/ubuntu/ lucid main restricted universe multiverse deb http://gb.archive.ubuntu.com/ubuntu/ lucid-updates main restricted universe multiverse deb http://gb.archive.ubuntu.com/ubuntu/ lucid-backports main restricted universe multiverse deb http://security.ubuntu.com/ubuntu/ lucid-security main restricted universe multiverse deb http://deb.example.org/apt/ubuntu/lucid/ binary/ And in /etc/apt/preferences.d/puppet: Package: puppet puppet-common Pin: release a=binary Pin-Priority: 800 Package: puppet puppet-common Pin: release a=lucid-backports Pin-Priority: -10 Currently policy says: $ sudo apt-cache policy puppet puppet: Installed: (none) Candidate: (none) Package pin: 2.7.1-1ubuntu3.6~lucid1 Version table: 2.7.1-1ubuntu3.6~lucid1 -10 500 http://gb.archive.ubuntu.com/ubuntu/ lucid-backports/main Packages 100 /var/lib/dpkg/status 2.6.14-1puppetlabs1 -10 500 http://deb.example.org/apt/ubuntu/lucid/ binary/ Packages 0.25.4-2ubuntu6.8 -10 500 http://gb.archive.ubuntu.com/ubuntu/ lucid-updates/main Packages 500 http://security.ubuntu.com/ubuntu/ lucid-security/main Packages 0.25.4-2ubuntu6 -10 500 http://gb.archive.ubuntu.com/ubuntu/ lucid/main Packages If I use n= instead of a= then I get Package pin: (not found) I'm just plain confused at this point as to what I should use. Any help appreciated.

Search Results

Search found 22224 results on 889 pages for 'point of sale'.

Page 628/889 | < Previous Page | 624 625 626 627 628 629 630 631 632 633 634 635 | Next Page >

- by watain

- by liv2hak

- by CodeByMoonlight

- by Greg

- by ThaKidd

- by Brian

- by macinjosh

- by rpkelly

- by Sebastian Zaklada

- by Syedur

- by jpolache

- by Jeff Atwood

- by Zimmy-DUB-Zongy-Zong-DUBBY

- by azera

- by William Jens

- by user70523

- by Felix

- by LaserBeak

- by Ephraim

- by Swapneel Patnekar

- by Dan

- by T.J. Crowder

- by grifaton

- by Hammer Bro.

- by Hamish Downer

< Previous Page | 624 625 626 627 628 629 630 631 632 633 634 635 | Next Page >