Search Results

Search found 2279 results on 92 pages for 'cable clutter'.

Page 63/92 | < Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >

• OpenBSD Routing Problem

  - by Ozkan SENOVA

  I am running OpenBSD on a network appliance hardware. It has 5 NICs. I want to give different IP's in same subnet to 3 nics. Eg: em0: 192.168.1.5 em1: 192.168.1.90 em2: 192.168.1.56 I make the necessary configuration with ifconfig, all interfaces works as expected when all the ethernet ports are plugged in to switch. But there is something wrong in routing. If I connect to 192.16.1.5 via any service(http, smtp etc.), traffic goes over link#3. If I unpug the cable from em2 I can't reach any IP's binded on device. Is there any way to route traffic over different links in this IP configuration?

  Read the article

• Infected Win XP disk not openable on a Vista computer

  - by Retired57

  How can I read a WinXP partioned disk that is infected and shows up on a USB connection to Win Vista computer as a single partition that Vista cannot see the contents? The XP computer HDD is partioned into 4 partitions. It became infected, and all attempts to clean it have failed. Applications begin to launch, but are then shut down by the infecting agent. Using a major Anti-virus Co. boot disk (which was unable to connect to the Web, probably because the infecting agent stopped it) with virus definitions dated after the disk became infected, the resultant scan showed no infection. I bought a USB cable to connect the IDE drive to my Vista computer, but when I open Win Explorer, it sees the disk, but does not show any contents. It indicates it is a single partition that is valid. However in all the ways I have tried it does not show drive contents. Any suggestions on what to do next?

  Read the article

• How to increase Remote Desktop resolution?

  - by BugAlert

  I'm using Windows 7 on a PC and connect to it via Remote Desktop Connection for Mac by MS, using a Mac. On the Mac, I have a 27" Display with 2560 x 1440 px resolution. The PC has a high performance graphics card (one of those that needs an additional power supply). Both machines are connected via network cable to a router. So network should be insanely fast. However, the max resolution I can get is 1400 x 1050. The PC just has a old and bad 21" monitor connected to it. How can I increase the resolution to 2560 x 1440 to work fullscreen with the Apple LED Cinema Display via Remote Desktop? Maybe I shouldn't even ask, because I already experience some lag at the low resolution of 1400 x 1050. But I guess this can be resolved as well?

  Read the article

• Can I use only a HDMI monitor?

  - by Felix

  I recently found out there are such things as PC monitors with TV capabilities (or TVs that can be PC monitors), and the idea kind of tickles my fancy. I'm thinking of getting one of these gadgets, and if I do, I will connect it to my PC via HDMI (my graphics card has builtin HDMI), so that I also get sound to the TV. The reason for this is because I have a 2.1 sound system which I want to use both on the PC and the TV. Basically, I want the configuration to look like this: Cable --------> TV --> 2.1 Sound System PC --HDMI--> TV --> 2.1 Sound System My question is: can I use a setup like this? Can I not have a classic VGA monitor? Will I be able to see non-graphical interfaces (such as the BIOS, GRUB, a Linux terminal, ...) through HDMI on the TV? I use Windows 7 and Ubuntu.

  Read the article

• How can I disrupt my roommate's BitTorrent?

  - by bob

  We're on a 50 mb/s Comcast connection and our connection right now is coming in under 1.5 mb/s. Our roommate left for a week with BitTorrent running (Azureus client, we think). Our latency is approaching 300 ms. His door is locked up tight, and both his machine and the router for the house are located inside. I've even flipped the power breaker in the house and that barely works for 2 minutes. His laptop keeps on running, and once the cable modem and router come back up and the machine reconnects, the torrents resume in earnest. I've been running nmap and identified his IP on our LAN. Is there anything I can do over the LAN to make his torrents start to fail or slow down?

  Read the article

• How can I connect a blu-ray player to a VGA screen?

  - by zaplwo

  Basically, I have a blu-ray player that I wanted to be connected to a projector and a monitor screen at the same time, so I got a component splitter and a component to VGA cable. The splitter works fine but the component to VGA adapter doesn't show anything on the monitor screen; is like if nothing is connected to it. I already change monitors but 3 monitors do the same. Anyone have any idea why this is happening or how can I connect the monitor and the projector to the blu-ray?

  Read the article

• plugging in a 3.3V 50pin laptop HDD to USB?

  - by barlop

  I have a 50pin laptop hard drive. 1.8" wide. This 50pin connector concerns me.. Even if I get an adaptor, How can I know which side of the connector takes the power? I don't want to plug it in the wrong way. And I don't have n adaptor.. Could people link me to adaptors too. but main question is, which side to plug it in when I get the adaptor. I want to be sure. I do not want to blow the hdd. For the 3.3V I have a plan. Connecting green and black and using the orange cable(3.3v) to feed power. I am not too worried about that bit. But as I said.. Main thing is I want to know which side is 3.3V hard drive is MK6006GAH

  Read the article

• Wireless only connects to Google

  - by dmanxiii

  I am using a netgear wireless router to connect to create a wireless network. When connected to the router via an Ethernet cable everything works correctly. When connecting to the router via wireless only Google can be accessed. I've done searches via Google using random words to make sure that it is not a cached page, and these all work. However, trying to connect to any non Google domain the page fails to load. I've accessed the connection with two different laptops, both are running Windows Vista. The network connection is strong on both, but the issue persists for both. Edit: I have configured the wireless networks name and password, and connect to that using the credentials I have defined. I am sure I am not connecting to a neighbors wireless network. Edit2: Typing in the direct IP address for CNN.com ( http://157.166.255.19 ) would not resolve.

  Read the article

• Text on Cisco ASA console is garbled/missing letters

  - by Some Linux Nerd

  I've actually looked up a number of solutions for this problem and none of them work. There's this Cisco ASA 5505 that I'd like to use, that outputs mildly garbled text with missing characters. I did some googling and found that the most likely problem is a bad baud rate, so I tried all the baud rates, 7N1, 8N2... basically every possibility minicom had. Then I figured (since I can type ok, just not read) that if I factory reset it that it would fix whatever is set wrong with the terminal. That didn't work either. This usb-db9 adapter and console cable work fine on the catalyst switch in our office. My serial settings are 9600 8N1 with no flow control. Anyone know how to fix this? I have an example of the text on pastebin: http://pastebin.com/MAJF0mVU - it's just lots of "Dfaut cnfiuraionfil cotais 1enty." instead of "Default configuration blah blah"

  Read the article

• Disable ALTQ for internal network traffic

  - by javanix

  I currently have a FreeBSD 8.2 media server set up on my LAN that I use to stream my music from. I also have an SSH login that I use to do file transfers to and from this server remotely. I would like to set up ALTQ (and have gotten this working) to limit my outgoing bandwidth from the server for SSH traffic. However, configuring ALTQ this way is also limiting my internal traffic (and thus interfering with my music streaming) since I am only using a single network interface. Can anyone show me how I would use PF and ALTQ to limit outgoing WAN traffic while allowing all internal LAN traffic to go through unhindered? ext_if="eth0" int_if="eth0" altq on eth0 cbq bandwidth 1Mb queue { std, ssh } queue std bandwidth 80% cbq(default) queue ssh bandwidth 20% cbq(ecn) pass out on eth0 proto tcp to port 22 queue ssh eth0 is my LAN interface, my total WAN bandwidth on my cable connection is 1Mb/s, and my internal network is 10/100.

  Read the article

• Samsung TV connected to PC for Powerpoint

  - by Skaughty

  I have a 42" Samsung LCD TV connected to a Dell computer with a PCI Radion 9000 via a 35' VGA cable. It's purpose is to run power point presentations over the TV for our retail store. I have tried every combination of button clicking on the video card options, and everything on the TV, and I still get black bars on the top and bottom of the image. It looks like I am watching a old wide screen movie on a full screen TV. The TV's suggested resolution is 1024x768, and that is what the output is set to. I have tried this with a nVida PCI card as well with the same results.

  Read the article

• Compaq Presario Laptop Monitor Problems

  - by Nishant

  I am attaching a few pics of my laptop monitor now . Can you please tell me if this is a hardware error which can be rectified by replacing the monitor ? How this happened - I accidently hit my leg on the laptop and jammed it against the wall and ever since the monitor is like this .I plan to replace the Monitor by buying a spare parts laptop that sells in ebay . I wonder if this is a LCD HARDWARE problem or problem with the cable that goes to the monitor . THE OS works fine in the computer .I hope my question is clear . http://img163.imageshack.us/gal.php?g=good1z.jpg

  Read the article

• windows 2008 server spooler problem

  - by air

  i have one windows 2008 server & windows xp clients. one HP2600n is connected to network with network cable, and installed in server and shared. also same printer is shared on xp cleints. the problem is: once cleints send print it come to the server que and stuck there untill we manually restart printer spooler service. once we restart the service all the prints in QUE prints and after that new prints again stuck in QUE till next manually restart. how can we solve this problem? Thanks

  Read the article

• How to charge an iPhone on a Windows PC without Installing iTunes

  - by Martin Hollingsworth

  I want to be able to charge my iPhone on my work computer, which is running Windows Server 2008 SP1 64-Bit. When I plug the iPhone in with the USB cable, it will not charge. Windows attempts to locate a driver for the device but only comes up with a generic Camera device and even if I allow that to be installed, the iPhone still does not charge. I have checked the computer's BIOS settings and did not find anything relating to power on the USB devices. I also tried this on ports at the back of the computer in addition to those on the front. The PC is a Dell Optiplex 780. As far as I can tell USB devices do not charge unless Windows has installed an appropriate driver. Since it is a work computer I do not want to install iTunes which does include a driver. I have a workaround that I will post as an answer for reference.

  Read the article

• Extend university wifi network [migrated]

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want? Thank you all

  Read the article

• How to route local traffic over switch?

  - by Franz Kafka

  I'm just cabled up at home but haven't got any way of verifying that gigabit speed can be reached. As I've only got one laptop with one network card, one cable, and one switch, I'm kind of stuck. I'm using a tool that you can start as a server or as a client to send data from one box to another. I would like to send and receive on the same Windows box. I guess if I use my network local IP address, my Windows 8.1 PC will just route traffic internally. Is there some way of forcing the traffic to go to the switch and back again?

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by casey_miller

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed) So the question is: What is a problem???

  Read the article

• Database for heat tolerances of various cables?

  - by I. F.

  Is there any kind of unified database of heat tolerances for networking cables? I've been setting up a number of home/small office networks lately and as a mostly-amateur I could really use some information on what is safe to run behind a radiator, next to a steam pipe, etc. The question I'm up against at the moment is: Can I run normal RJ11 phone line cable (from DSL modem to phone jack) behind a steam radiator without risking a fire? Unlike cat5, I could not find published standards for these, so I'm turning to experts with more experience. This is a cut-rate show. Do I go out and buy more cabling, and if so which, or use the spare that I have?

  Read the article

• Primary monitor keeps reverting back to the laptop display

  - by Celeritas

  A Macbook Pro running VMware Fusion has a guest operating system of Windows 7. The user often connects an external monitor to the laptop through an HDMI cable. For the display settings "extend the desktop" is selected and I keep setting the primary monitor as the external one but for some annoying reason it keeps changing back. So after Windows starts the taskbar and icons are on the laptop screen which we don't want. I know how to change it but it keeps changing back (and the computer user is non-technical).

  Read the article

• Slow internet connection on Mac OS

  - by user984621

  At home, we have a router. From router goes the internet connection into the desktop PC (Windows 7) and Macbook Pro. The problem is, that on Mac OS is incredibly slow internet connection - is not possible to use the laptop for surfing on the internet. The same as for WiFi as for cable. On the PC with Windows 7 is working the internet connection properly. Is there any tool for testing, if on my Mac is a virus or just something, what slowing down the internet connection? THank you in advance.

  Read the article

• Can't access internet even though everything is working

  - by entity64

  A friend recently upgraded to a new cable internet connection. The modem connects to the router and various PCs and smartphones from her roommates connect to the router. They don't have any problem accessing the internet. She has Windows 8 and can't access any website (via wifi and ethernet). DNS (UDP) is working, DHCP set up everything correctly, Wifi is working, Trace routes and Pings (ICMP) go through with no problem at all. But neither Dropbox nor Skype nor Spotify nor any browser (all TCP) can access any website. The thing is though, she can connect through the university wifi and via a neighbors wifi. It's just her home connection. No firewalls are running and the computer is clean - no malware. How could it be that only her home connection won't work and others do?

  Read the article

• Rate of UDP packet loss over WLAN

  - by Martin

  While testing something with TFTP I noticed lots of timeouts (and slow speed as result) when I used my WLAN - and no problems when using a network cable. A quick test program sending/receiving UDP revealed that there are about 3-5% packets lost. While it's obvious that WLAN has to be less reliable than LAN, I have no knowledge what loss rates are considered 'normal' - and when there is a need to further investigate the network infrastructure. Are there 'typical' packet loss rates on WLAN (and other network technologies e.g. PowerLAN, WAN, ...? Thanks

  Read the article

• Planning office network [closed]

  - by gakhov

  I'm planning to setup my office network from scratch and want to ask professional opinions or tips. My office is connected to Internet with Cable connection (100Mb/s). The devices i would like to connect are VoIP Phone (RJ-11), TV (WiFi/LAN), 3 laptops (WiFi), a few smartphones (WiFi), iPad (WiFi), Kindle (WiFi) and, probably, MediaServer (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, i need help to choose the best routers combination (or even one?) to support stable connections for all these devices and minimize the total number of routers/adapters. Any thoughts? Thank you!

  Read the article

• VMware - Broadcom 1000Gbps NIC does not link at 100Mbps to a Cisco switch port

  - by Spirit

  Today we've stumbled on a very awkward situation with our VMWare Server. The server is with ESX 3.5 that has a 1Gbps NIC. We bought a brand new managed Cisco Linksys switch with 10/100Mbps interface ports but when we plugged the cable in one of the ports the link simply does not wanted to activate :S... Does anyone with more VMware experience have ever had similar problem? From what I know is that 1Gbps NICs are backwards compatible with 100Mbps switches. This is what we've tryed so far but with no success: Tryed: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004089 Tryed to modify the /etc/modules.conf folowing the guide from this article http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=813 After the changes I have restarted the networking services using # service network restart, # service mgmt-vmware restart and # service vmware-vpxa restart It seems that no matter how many times, or whatever approach/method (GUI or Shell) we try to change the speed and duplex of the network adapter and to force it to 100mbps it only accepts 1Gbps .. I am starting to go nuts :@

  Read the article

• Boxee on Dell 32in TV causes headaches, how to troubleshoot?

  - by brown145

  I have revamped an old pc, installing 4GB ram and a 256MB video card so that I could run Boxee to a Dell W3200 series TV that came with my apartment. It is connected via VGA, resolution is 1360x768, 24bit color, 60Htz refresh rate. Unfortunately, every time I use it I end up with a headache after less that 30 min. I have had my eyes check recently, and am able to play xbox (connected via hdmi) on the same TV without problems. What are the potential causes? My system seems to well meet or exceed the min requirements for boxee, XP, AMD Atholon 64 X2 Dual Core, 4GB RAM. Could it be the VGA cable? What is the most cost effective way to trouble shoot?

  Read the article

< Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >