Search Results

Search found 37414 results on 1497 pages for 'open port'.

Page 633/1497 | < Previous Page | 629 630 631 632 633 634 635 636 637 638 639 640  | Next Page >

• 3 Monitors, 1 graphics card

  - by mikelbring

  I have a Nvidia GT 120 graphics card. It has a VGA, DVI and DMI output. Can I have 3 monitors with this? One for each port. Also if not, can I use DVI and HDMI and have 2 monitors. I know I can do 2 with the VGA and DVI but I am wondering about DVI and HDMI. Also my last question is, if I can have 2 monitors with the DVI and HDMI, can I use a HDMI to DVI cable and still have the same success?

  Read the article

• Steps to make sure network is not blacklisted...Again

  - by msindle

  I have an interesting issue. I have a client that just got blacklisted due to spam being sent out over the last 2 days. I have my firewall configured to only allow mail to go outbound on port 25 from our mail server (Exchange 2010) exclusively and I have verified that there are no open relay's on our transport rules. We are running Vipre Business and after running deep scans with updated definitions all computers come back clean. I ran a message tracking report on our Exchange server that shows all mail sent via the mail server over the last couple of weeks and didn't see anything malicious or out of the ordinary. I have also verified that there are no home devices or rouge computers on the network. For all practical purposes it appears that the network is clean, but we still wound up on 5 or 6 blacklists...Where should I start looking next? Is there a "best practices" guide that can help eradicate this issue? Thanks in advance! msindle

  Read the article

• Outlook Anywhere remote https connection issue

  - by holian

  We have SBS 2003, and we use DYNDNS. We forward dyndns address 443 to local server ip 443 port. mycompany.dyndns.org:443 -- server.mycompany.local:443 In android phone i can check my mails with Outlook Active Snyc. From remote machine i can check my mails in owa (https://mycompany.dyndns.org/exchange) But i can't set up outlook 2013 to remote connect. I installed server.mycompany.local to remote machine trusted cert container, but i got error message: "There is a problem with the proxy server's security certificate. The name on the security certificate is invalid or does not match the name of the target site. Outlook is unable to connect to the proxy server. (Error Code 10)" Is it possible to connect exchange, via dnydns? Whats the problem? Thank you

  Read the article

• HP Z210 SFF: two different video cards produce no Displayport output when installed

  - by ConcernedOfTunbridgeWells

  I have a HP Z210 SFF that I'm trying to install a video card into. I've tried two different cards in Slot 2 (a Quadro FX380LP and a Quadro 600). Neither of these cards produce a displayport signal when installed. With neither installed the displayport port on the motherboard works fine with the built in graphics. When I install the cards it produces no signal and the cards don't either. The Quadro 600 is brand new and the odds of having two dead video cards is quite low. Is there something fundamental that I could be missing out - a BIOS setting maybe?

  Read the article

• Scrolling mouse sets windows sound volume

  - by Ikke

  Suddenly, when I use the scroll wheel of my mouse, it changes the windows sound volume level. I have a HP DV6-2030SD laptop with Windows 7 64 bit and a Zolid p50622 mouse. When I use the scroll function of the mouse pad of the laptop, it does not adjust the sound level. I don't have any special mouse drivers installed, just the standard windows drivers. When I scroll, I see the HP sound level screen: It doesn't do it always, but when it does, it prevents the current window to scroll, which is really annoying. Rebooting doesn't help. I've tried to put the USB dongle in a different port, but this doesn't help either. Any advise on how I can fix this?

  Read the article

• Connect macbook to my LAN through a VPN - best solution?

  - by LewisMc

  So I have a LAN connected via a ADSL/PPPoA, this is using a bog-standard DLink router supplied by my ISP (talktalk UK). I have a NAS within the LAN that is running FreeNAS and I want to be able to connect to it when I'm out and about. It's running an atom so it's quite low on juice consumption but I don't want to have it on all day and night so I've been waking it via a magic packet and booting it down from the web admin when I need it. So I want to connect to the LAN, I presume via a VPN, to be able to send a magic packet. But what is the best method to accomplish this, or is there an easier way? I've been looking at the cisco 857 integrated router and the Netgear prosafe 318(behind modem) but not sure If I'm on the right track with what I want to achieve as I've not much experience or knowledge with VPN's or networking (software engineering student). I have tried port forwarding but to no avail, either with magic packets or even connecting outside the LAN via DYNDNS. Thanks,

  Read the article

• Unable to connect to Cygwin from Mac OS X by ssh

  - by skyjack

  I've started ssh server on Windows 7 using Cywgin and I'm trying to connect to it by ssh from Mac OS X Mavericks. It fails with next error: ./ssh username@hostname -v OpenSSH_6.6, OpenSSL 1.0.1g 7 Apr 2014 debug1: Reading configuration data /usr/local/etc/ssh/ssh_config debug1: Connecting to hostname [my ip] port 22. debug1: Connection established. debug1: identity file /Users/skyjack/.ssh/id_rsa type -1 debug1: identity file /Users/skyjack/.ssh/id_rsa-cert type -1 debug1: identity file /Users/skyjack/.ssh/id_dsa type -1 debug1: identity file /Users/skyjack/.ssh/id_dsa-cert type -1 debug1: identity file /Users/skyjack/.ssh/id_ecdsa type -1 debug1: identity file /Users/skyjack/.ssh/id_ecdsa-cert type -1 debug1: identity file /Users/skyjack/.ssh/id_ed25519 type -1 debug1: identity file /Users/skyjack/.ssh/id_ed25519-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.6 ssh_exchange_identification: read: Connection reset by peer Meanwhile I can connect successfully from Red Hat. OpenSSH version on Cygwin: OpenSSH_6.4p1, OpenSSL 1.0.1f 6 Jan 2014 OpenSSH version on MAC OS X: OpenSSH_6.6p1, OpenSSL 1.0.1g 7 Apr 2014 Please advice.

  Read the article

• so i installed sql server now how do i connect to it?

  - by letseatlunch

  SO i have a server running windows server 2008 r2 and i just installed Microsoft sql server 2008. I used the manager thing to create the database and the tables, etc and now i want to connect to it via my visual studio which is on a different machine. so how do i do that? do i need to "turn on" the sql server, do i need to do port forwarding? do i have to modify the iis or change those settings? is there a good article someone can me point me to? just to further help you help me, i understand how to connect to a datasource in visual studio my problem is more with the sql server and understanding how to properly set it up once installed. Sorry for the noob question, i got it all installed and i know how to use it once its all going i just don't know the in-between. thanks in advance dave

  Read the article

• How do I configure Shrewsoft's VPN client to only route traffic to a certain IP address through the VPN?

  - by dommer

  We're using Shrewsoft's VPN client to connect to a third party development server. However, it seems to be configured to send all or nothing through the VPN. The devs have to disconnect from the VPN to get email/internet access back. The server that needs to be accessed via the VPN is on a specific (local - 10.x.x.x) IP address and a specific ports. Can we configure the Shrewsoft client application to only route traffic to that one address and/or port through the VPN and to route anything else though the usual channels? If so, how is it done? I'm not a VPN specialist and the options are confusing. In the absence of any Shewsoft VPN client specific advice, what should I be search for? Split tunnels?

  Read the article

• Macbook Pro (SantaRosa) internal display not detected by graphics card, external monitor OK

  - by BLAU

  My MacBook Pro (2.4 Ghz, Santa Rosa with infamous nVidia card) acts strange. It shows the normal gray screen with Apple logo and animation flawlessly during start up but the internal display goes black without any rendering at all when all is loaded. (shining a light on display show nothing) If an external monitor is connected through the DVI port it will remain black during start up and then show the desktop as the internal display goes black. This happens both while booting to Mountain Lion and Windows XP. I have checked "About my Mac" and only the external display is listed. The same is the case if I use the nVidia Control panel in Windows XP. My questions: Is this a hardware problem or is it related to software maybe even firmware? What controls the display during start up, graphics card or something else?

  Read the article

• Cannot access site via IP / hostname

  - by DaveB

  I am renting a VPS with Debian installed running JBoss AS6 for my web app. I recently had some problems with my DNS hosts as they messed up the A-records for my domain which caused some new A-records to be added by mistake The DNS problem is now sorted and the domain is working ok, however I noticed that the web server no longer responds via direct IP or hostname in a web browser (although it pings ok and I can SSH in using the hostname ok) Is there any explanation for this? I am using rinetd to forward traffic from 80 to port 8080 but thats been ok for a while Any suggestions would be appreciated Regards

  Read the article

• How can I remove LibUSB on Windows 7?

  - by Cokegod

  I've installed LibUSB, a software that modifies your USB driver so that programs can access it easily. I didn't know that in Windows 7 you have to run it in compatibility mode for Windows XP, so now my Windows 7 can't access any USB port (including keyboard and mouse). Now I can't access my computer at all, and I don't have any PS2 connection in my computer. I tried to run it in Safe Mode but it didn't change anything. I tried to run a system restore from before the installation of LibUSB, but all the restore points give me an error: "The instruction at 0x73888f18 referenced memory at 0x00000004. The memory could not be read." I also tried to run Hiren's Boot CD and remove all the files associated with LibUSB, but that didn't change anything. So how can I remove LibUSB and access my computer again without formatting my hard drive? (I have important things on it)

  Read the article

• Bound external Cisco CIGESM ports to a specific BladeServer

  - by Vinícius Ferrão

  We have an IBM BladeCenter with 14 blade servers and one external Cisco CIGESM for Ethernet connectivity. Since this hardware is a little old, we will use it for other services, and we want to run a pfSense instance on one of the blades. It's just an Firewall Appliance, but it needs two network interfaces: one for the WAN and the other one for LAN access. Our architecture works on top of static routes, we don't use NAT, so we got the WAN IP in one interface routing to the another one. The main problem is how to plug the WAN cable in one of the four external ports and make it exclusive to the blade server containing the firewall. And we also need an exit port that goes through a 3COM 4200G switch that makes the internal routing and VLAN separation. Thanks in advance

  Read the article

• What's wrong with my MAC address?

  - by Shaul

  I have a D-Link DSL-2650U router, and exactly one computer on the network. For reasons of port forwarding I want to give my computer a static internal IP address, so that I don't take the chance of losing my NAT settings every time the computer reboots. So here's a screen shot that summarizes the entire problem: WTH is wrong with my MAC address? It's copied and pasted from the command prompt window! I tried editing out the dashes, but it still doesn't work. Am I doing something wrong, or is there a bug in the D-Link firmware?

  Read the article

• Exchange unable to relay mail outbound

  - by Saif Khan

  I have some users congigured in exchange 2003 (delivery options tab) to forward mails to their external address. This was working fine until today. The mails are being held up in the SMTP queue folder. I am able telnet the addresses (e.g. google.com) at port 25 from the server. Any reason why the mails are held up? Other emails are going ou. It's only the mailboxes configured to forward the mail out to the public email addresses. I also did the following Check event logs for errors. Nothing. Checked my domain on blacklists. Nothing. Any idesa?

  Read the article

• rdesktop + seamlessrdp + virtualbox slow on Windows

  - by Claudiu

  I'm trying to get VirtualBox seamless mode to work on all of my monitors at once. I was directed to this link, so I followed the instructions, using the windows port of rdesktop 1.6 found here, and using Xming as an X server. I eventually finally got it to work! However, it's really slow. While VirtualBox's regular seamless mode is as performant as if I was running apps on my host machine, with rdesktop it takes 1-2 seconds to register any user input. Dragging windows around is laggy and buggy (pieces of the desktop behind the window show through). I'm simply connecting to localhost, so network bandwidth/latency shouldn't be an issue... anyone have any idea why it's so slow and what I can do to make it more performant?

  Read the article

• SSL client auth in nginx with multiple server section

  - by Bastien974

  I want to implement ssl_verify_client in nginx. This works perfectly when I only have one server section, which listen to 443. In my case I have multiple, all listening on 443 but to different server_name. For one particular server (proxy.mydomain.com), I'm adding the SSL client verify, but when I test the connectivity with openssl s_client -connect proxy.mydomain.com:443 -cert xxx.crt -key xxx.key and then do a GET / HTTP/1.1 host: proxy.mydomain.com It's not working, 400 No required SSL certificate was sent I think nginx is not receiving the proper server_name and is directing it to the first server listening to 443. So I tried to listen on another port and it worked right away. What's the issue and how can I fix it ?

  Read the article

• Yum through http proxy

  - by eodchop

  Hello, I have several Fedora 13 servers that have to connect through an http proxy for yum updates. All port 80 traffic has to be routed through this proxy. I have setup the proxy server in the network settings GUI. I can browse the internet just fine. I have also setup my proxy information in /etc/yum.conf as follows: proxy=http:proxy.largecorp.corp/accelerated_pac_base.pac proxy_user=user proxy_password=password I then added the export HTTP_PROXY="http:proxy.largecorp.corp/accelerated_pac_base.pac" to /etc/bashrc and sourced the file. When i run yum update: Loaded plugins:presto, refresh-packagekit Error: Cannot retrieve repository metadata (repomd.xml) fro repository: fedora. Please verify its path and try again. All of the repo urls are the defaults, as this is a fresh install.

  Read the article

• OpenVPN route missing

  - by dajuric

  I can connect to an OpenVPN server from Windows without any problems. But when I try to connect from Ubuntu 12.04 (start OpenVPN) I receive the following: OpenVPN needs a gateway parameter for a --route option and no default was specified by either --route-gateway or --ifconfig options SERVER IP: 161.53.X.X internal network: 10.0.0.0 / 8 What I need to do ? client configuration: client dev tap proto udp remote 161.53.X.X 1194 resolv-retry infinite nobind ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 server conf: local 161.53.X.X port 1194 proto udp dev tap dev-node OpenVPN ca ca.crt cert server.crt key server.key # This file should be kept secret dh dh1024.pem # DHCP leases addresses to clients server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. push "route 10.0.0.1 255.255.0.0" client-to-client duplicate-cn keepalive 10 120 comp-lzo verb 6

  Read the article

• How to allow an internal server accept remote connections not through RD Gateway

  - by Matt Ahrens

  So, I help administrate a collection of servers running various windows server environments. We have a RD Gateway server, properly configured, to gatekeep for us. It does not have the other servers listed in it's server farm category, though. I just added a refurbished server for a non-profit development environment that is sharing the rack space and port. I would like this server to be accessible via remote connection, but not require RD gateway certification (I cannot add the users for this development server to our gateway since they do not work for the organization hosting the rack.) Is there any way for me to add this dev. server as an exception to which servers should require RD Gateway clearance, or otherwise let users bypass RD gateway credentials for this one machine? Thanks, and let me know if I am misinformed on how RD gateway works or anything. I am still learning.

  Read the article

• How do I unmount a charging device in Linux?

  - by PeanutsMonkey

  I have a mobile device attached via USB to a Linux box and wish to unmount it. I ran the command fdisk -l however it does not list a mount point. I then ran the command lsusb which yielded the screenshot below. I then proceeded to search the /dev/disk/by-id directory and was found the following file The file is a symbolic link to what appears to be /dev/sdc Questions Why does it not appear when I run the command fdisk -l? How do I unmount it properly without simply yanking the USB cord from the USB port?

  Read the article

• Window 2003 Server - Logon Failure error message in Event Viewer

  - by user45192

  Hi guys, I received alot of event logged in the event viewer with this message. I notice is always the same user id which encounters this error. The user id is use by an application to access the database. However, this account does not exits on this server. How do I trace the services/program use by this user id which causes these error messages? Reason=Unknown user name or bad password&&User Name=&&Domain=&&Logon Type=3&&Logon Process=NtLmSsp&&Authentication Package=NTLM&&Workstation Name=&&Caller User Name=-&&Caller Domain=-&&Caller Logon ID=-&&Caller Process ID=-&&Transited Services=-&&Source Network Address=-&&Source Port=-&&User=SYSTEM&&ComputerName=

  Read the article

• block access to wrt from vlan using iptables dd-wrt

  - by NitroxDM

  I set up multiple isolated vlans in dd-wrt. Now I need to forward a port to vlan2. I isolated the vlans using: iptables -I FORWARD -i br0 -o vlan2 -j DROP iptables -I FORWARD -i br0 -o vlan3 -j DROP iptables -I FORWARD -i br0 -o vlan4 -j DROP Now I need to block a clients on each vlan from accessing the router. This doesn't work: iptables -I INPUT -i br0 -o vlan2 --dport telnet -j REJECT --reject-with tcp-reset I'm new it iptables... am I missing something?

  Read the article

• How do I force a specific MTU for only certain TCP ports?

  - by Dave S.

  Background I have a set of embedded hardware deployed in the field. These remote machines connect back to my servers at AWS running Ubuntu and I use the iptables mangle chain to lower the MTU to 500 so these devices are happy. For reference, this is the iptables rule I am using: -A POSTROUTING -p tcp --sport 12345 --tcp-flags SYN,RST SYN -o eth0 -j TCPMSS --set-mss 500 Current Problem I'm trying to spin up some servers on the Joyent Cloud using SmartOS, but I can't find any information on selectively changing the MTU like I can on Linux (e.g. all info I've found is on changing it globally, which is not what I want). How would I do it so that all connections on TCP port 12345 get the MTU I want?

  Read the article

• Unable to connect to remote MS SQL Server 2008 Express SP3 instance by name

  - by Max

  I am trying to connect to a remote MS SQL Server 2008 SP3 x86 Instance using it's name. At the first glance all seems to work well (e.g. it is possible to connect to the server locally and succesfully telnet it's port remotely), but there is a thing I can't understand... This line should connect us to the default instance of remote SQL Server: osql -S ServerIP -d MyDatabase /U sa -P MyPassword and it does the trick, however the next one: osql -S ServerIP\MyInstance -d MyDatabase /U sa -P MyPassword ends up with the following error: [SQL Native Client]SQL Network Interfaces: Error Locating Server/Instance Specified [xFFFFFFFF]. [SQL Native Client]Login timeout expired [SQL Native Client]An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. The only instance running on the server is MyInstance, which is (I guess) the default one. Could you please put some time in explaining the issue.

  Read the article

< Previous Page | 629 630 631 632 633 634 635 636 637 638 639 640  | Next Page >