Search Results

Search found 15295 results on 612 pages for 'gwt hosted mode'.

Page 64/612 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Configuration for httphandler in classic mode

    - by happyspider
    I have to install an httphandler that needs to run on classic mode. I have created an application on the iis that uses a classic apppool and put the handler assembly there. The vendor gave me a configuration in the deployment document that looks like this: <system.web> <globalization requestEncoding="iso-8859-1" responseEncoding="iso-8859-1" /> <httpModules> </httpModules> <httpHandlers> <add verb="*" path="*" type="ProductName.ProductName, ProductName" /> </httpHandlers> </system.web> <system.webServer> <validation validateIntegratedModeConfiguration="false"/> <handlers> <add name="someUnspecificName" path="*" verb="*" modules="IsapiModule" scriptProcessor="C:\Windows\Microsoft.NET\Framework\v2.0.50727\aspnet_isapi.dll" resourceType="Unspecified" requireAccess="None" preCondition="classicMode,runtimeVersionv2.0,bitness32" /> </handlers> </system.webServer> The error I get when requesting a URL on the application is a 404, so I guess the handle is not used at all. Does the configuration look ok for a 64bit system?

    Read the article

  • Xbox Music ignores Asus FN media keys in Desktop Mode

    - by Ruud Lenders
    I have an Asus PRO64JQ laptop, and I recently upgraded to Windows 8. The FN keys stopped working, so I tried to install default drivers using the CD that came with my laptop. Unfortunately, the CD does not support Windows 8. Asus Support does not help me either. It seems that Asus does not support Windows 8 on my model, since I can't find it in their list of Windows 8 upgradable models. Also, the support page of my laptop does not allow me to select Windows 8 as OS. That's why I'm asking my question here. I fixed (most of) the FN keys by installing the ATKPackage, and I was happy to find out that the media keys (play/pauze, next, previous) works with the Xbox Music app. But the keys only work in the Metro UI. In Desktop Mode, pressing FN+? (play/pause) starts up Windows Media Player. Disabling Windows Media Player through the control panel stops it from popping up, but Xbox Music still only responds to them in the Metro UI. I remember that I had similar problems when I tried to make these media keys to work with iTunes on Windows 7. The fix there was a small iTunes plug-in. So tell me, do you know how to fix my problem? Thanks.

    Read the article

  • Linux boot - stop the kernel switching to a new framebuffer mode clearing output

    - by Avio
    I'm working on an embedded system (based onUbuntu 12.04 LTS) and I'm customizing its kernel. I'm having some problem with upstart, mountall and plymouth. Nothing unsolvable I suppose, but the real problem is that I can't diagnose properly what's going on because the kernel (or maybe plymouth) changes the video mode in the middle of the boot process. This completely wipes entire lines of log and prevents any debugging of kernel misconfigurations. My Grub2 config seems to be ok with: GRUB_CMDLINE_LINUX="" GRUB_CMDLINE_LINUX_DEFAULT="acpi=force noplymouth" GRUB_GFXMODE=1024x768x32 GRUB_GFXPAYLOAD_LINUX=keep Here is some relevant output of lspci: 00:00.0 Host bridge: Intel Corporation Mobile 945GSE Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GSE Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) And here is the relevant portion of my kernel configuration: CONFIG_AGP=y CONFIG_AGP_INTEL=y CONFIG_VGA_ARB=y CONFIG_VGA_ARB_MAX_GPUS=16 CONFIG_DRM=y CONFIG_DRM_KMS_HELPER=y CONFIG_DRM_I915=y CONFIG_DRM_I915_KMS=y CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_FB=y CONFIG_FB_BOOT_VESA_SUPPORT=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y CONFIG_FB_MODE_HELPERS=y CONFIG_FB_VESA=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=y CONFIG_VGA_CONSOLE=y CONFIG_VGACON_SOFT_SCROLLBACK=y CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=640 CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y CONFIG_LOGO=y CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y Every other custom/stock kernel boot fine with that Grub2 config. What I would like to have is a single flow of messages on a single console (retaining one screen resolution) from the bootup logo till the login prompt. Does anybody know what I have to tweak to achieve this?

    Read the article

  • Windows 7 BSOD, safe mode working,

    - by mil0ck
    I need help getting my dualboot with Windows 7 and Ubuntu 12.04 to work, and since I'm not to experienced with computers I've been pretty dumb. Here's what I've done, quite shortend though: First removed a Ubuntu 10.04 partion, and replaced bootloader using EasyBCD Installed Ubuntu 12.04 on same partion as before Decided I need more space so I shrinked my C: partion (Windows partion) using Here, after rebooting my computer, I was stuck a grub rescue, when booting up the computer I fixed that by using SuperGrubDisk Rescatux and then using my Windows Vista install disk to repair the computer (computer is using Windows 7) I know re-installed Ubuntu 12.04 on the linux partion and got the GRUB-bootloader working Then, after using my computer for several hours, I installed beta drivers (version 304.79) for my GeForce GTS 240 and then rebooted my computer. At the first boot (after reboot) my computer just crashed, and here I am When trying to boot Windows 7 now I get a Blue Screen Of Death. I can though boot in to safe mode with everything working. I have uninstalled the beta drivers and installed the same one as before but still the same problem. I have tried all the commands in Bootrec.exe and none is working. I can't neither find an OS when using Bootrec.exe/ScanOs. I have also tried running: sfc/scannow and that comes out clean. Short: My harddrive and files seems to be intact but when booting I get bluescreen. I can though boot in to safemode with everything working. I need help Thanks to anyone who even took the time to read that. //mil0ck

    Read the article

  • SSL confirmation dialog popup auto closes in IE8 when re-accessing a JNLP file

    - by haylem
    I'm having this very annoying problem to troubleshoot and have been going at it for way too many days now, so have a go at it. The Environment We have 2 app-servers, which can be located on either the same machine or 2 different machines, and use the same signing certificate, and host 2 different web-apps. Though let's say, for the sake of our study case here, that they are on the same physical machine. So, we have: https://company.com/webapp1/ https://company.com/webapp2/ webapp1 is GWT-based rich-client which contains on one of its screens a menu with an item that is used to invoke a Java WebStart Client located on webapp2. It does so by performing a simple window.open call via this GWT call: Window.open("https://company.com/webapp2/app.jnlp", "_blank", null); Expected Behavior User merrilly goes to webapp1 User navigates to menu entry to start the WebStart app and clicks on it browser fires off a separate window/dialog which, depending on the browser and its security settings, will: request confirmation to navigate to this secure site, directly download the file, and possibly auto-execute a javaws process if there's a file association, otherwise the user can simply click on the file and start the app (or go about doing whatever it takes here). If you close the app, close the dialog, and re-click the menu entry, the same thing should happen again. Actual Behavior On Anything but God-forsaken IE 8 (Though I admit there's also all the god-forsaken pre-IE8 stuff, but the Requirements Lords being merciful we have already recently managed to make them drop these suckers. That was close. Let's hold hands and say a prayer of gratitude.) Stuff just works. JNLP gets downloaded, app executes just fine, you can close the app and re-do all the steps and it will restart happily. People rejoice. Puppies are safe and play on green hills in the sunshine. Developers can go grab a coffee and move on to more meaningful and rewarding tasks, like checking out on SO questions. Chrome doesn't want to execute the JNLP, but who cares? Customers won't get RSI from clicking a file every other week. On God-forsaken IE8 On the first visit, the dialog opens and requests confirmation for the user to continue to webapp2, though it could be unsafe (here be dragons, I tell you). The JNLP downloads and auto-opens, the app start. Your breathing is steady and slow. You close the app, close that SSL confirmation dialog, and re-click the menu entry. The dialog opens and auto-closes. Nothing starts, the file wasn't downloaded to any known location and Fiddler just reports the connection was closed. If you close IE and reach that menu item to click it again, it is now back to working correctly. Until you try again during the same session, of course. Your heart-rate goes up, you get some more coffee to make matters worse, and start looking for plain tickets online and a cheap but heavy golf-club on an online auction site to go clubbing baby polar seals to avenge your bloodthirst, as the gates to the IE team in Redmond are probably more secured than an ice block, as one would assume they get death threats often. Plus, the IE9 and IE10 teams are already hard at work fxing the crap left by their predecessors, so maybe you don't want to be too hard on them, and you don't have money to waste on a PI to track down the former devs responsible for this mess. Added Details I have come across many problems with IE8 not downloading files over SSL when it uses a no-cache header. This was indeed one of our problems, which seems to be worked out now. It downloads files fine, webapp2 uses the following headers to serve the JNLP file: response.setHeader("Cache-Control", "private, must-revalidate"); // IE8 happy response.setHeader("Pragma", "private"); // IE8 happy response.setHeader("Expires", "0"); // IE8 happy response.setHeader("Access-Control-Allow-Origin", "*"); // allow to request via cross-origin AJAX response.setContentType("application/x-java-jnlp-file"); // please exec me As you might have inferred, we get some confirmation dialog because there's something odd with the SSL certificate. Unfortunately I have no control over that. Assuming that's only temporary and for development purposes as we usually don't get our hands on the production certs. So the SSL cert is expired and doesn't specify the server. And the confirmation dialog. Wouldn't be that bad if it weren't for IE, as other browsers don't care, just ask for confirmation, and execute as expected and consistantly. Please, pretty please, help me, or I might consider sacrificial killings as an option. And I think I just found a decently prized stainless steel golf-club, so I'm right on the edge of gore. Side Notes Might actually be related to IE8 window.open SSL Certificate issue. Though it doesn't explain why the dialog would auto-close (that really is beyong me...), it could help to not have the confirmation dialog and not need the dialog at all. For instance, I was thinking that just having a simple URL in that menu instead of have it entirely managed by GWT code to invoke a Window.open would solve the problem. But I don't have control on that menu, and also I'm very curious how this could be fixed otherwise and why the hell it happens in the first place...

    Read the article

  • Error Installing ruby with RVM Single User mode on Arch Linux

    - by ChrisBurnor
    I've just installed RVM on ArchLinux x64 in single user mode via the recommended install script curl -L https://get.rvm.io | bash -s stable I've also installed all the requirements listed in rvm requirements However, I'm having trouble actually installing any version of ruby. And getting the following error: arch:~ % rvm install 1.9.3 No binary rubies available for: ///ruby-1.9.3-p194. Continuing with compilation. Please read 'rvm mount' to get more information on binary rubies. Fetching yaml-0.1.4.tar.gz to /home/christopher/.rvm/archives % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 460k 100 460k 0 0 702k 0 --:--:-- --:--:-- --:--:-- 767k Extracting yaml-0.1.4.tar.gz to /home/christopher/.rvm/src Prepare yaml in /home/christopher/.rvm/src/yaml-0.1.4. Configuring yaml in /home/christopher/.rvm/src/yaml-0.1.4. Error running ' ./configure --prefix=/home/christopher/.rvm/usr ', please read /home/christopher/.rvm/log/ruby-1.9.3-p194/yaml/configure.log Compiling yaml in /home/christopher/.rvm/src/yaml-0.1.4. Error running 'make', please read /home/christopher/.rvm/log/ruby-1.9.3-p194/yaml/make.log Please note that it's required to reinstall all rubies: rvm reinstall all --force Installing Ruby from source to: /home/christopher/.rvm/rubies/ruby-1.9.3-p194, this may take a while depending on your cpu(s)... ruby-1.9.3-p194 - #downloading ruby-1.9.3-p194, this may take a while depending on your connection... ruby-1.9.3-p194 - #extracting ruby-1.9.3-p194 to /home/christopher/.rvm/src/ruby-1.9.3-p194 ruby-1.9.3-p194 - #extracted to /home/christopher/.rvm/src/ruby-1.9.3-p194 Skipping configure step, 'configure' does not exist, did autoreconf not run successfully? ruby-1.9.3-p194 - #compiling Error running 'make', please read /home/christopher/.rvm/log/ruby-1.9.3-p194/make.log There has been an error while running make. Halting the installation. The log files are as follows: arch:~ % cat ~/.rvm/log/ruby-1.9.3-p194/yaml/configure.log __rvm_log_command:32: permission denied: arch:~ % cat ~/.rvm/log/ruby-1.9.3-p194/yaml/make.log make: *** No targets specified and no makefile found. Stop. arch:~ % cat ~/.rvm/log/ruby-1.9.3-p194/make.log make: *** No targets specified and no makefile found. Stop.

    Read the article

  • Does Windows 7 RC handle non Windows Media Center remotes yet?

    - by zillion
    I'm mostly a Linux geek, but while I will be trying to make my first Arch Linux installation in a virtual machine to learn and make my installation script for the true install, I need a simple OS and Windows 7 was better than Windows XP Media Center cause Media Center is outdated on XP. I tested it has a beta but my Hauppauge wintv-pvr usb2 remote wasn't working but the tv-tuner worked well and I haven't tested Windows XP Mode and my printer Epson Stylus Photo R300. Do someone know this hardware and if the XP Mode is easily supported?

    Read the article

  • External USB disk drive cannot be remounted in Windows XP

    - by jackhab
    I have Maxtor Basics Desktop 1TB external USB drive connected to Windows XP. The dirve's firmware puts it to sleep after 10-20 min of inactivity and then the drive cannot be mounted unless I reset it via power connector. While in sleep mode I can see the device in the Device Manager under both Disk drives and USB sections. Is there a way to get the drive out of sleep mode without hard reset? Thanks

    Read the article

  • Integration features enabled but drives not available

    - by dsjbirch
    Frustratingly, after a recent update to Windows XP mode integration features, the availability of shared disks from the hosts has been impaired. Does anyone know any kind of workaround or fix (excluding dropbox et al)? I have tried completely uninstalling and reinstalling as per http://www.sevenforums.com/virtualization/63710-refreshing-xp-mode.html#post568715 At one point restarting the machine appeared to have worked, but today again I am without access to my host. Interestingly audio and copy and paste to and from the machine are working.

    Read the article

  • How to manage security of these self hosted web apis, to ensure that the request coming for accessing data is authenticated?

    - by Husrat Mehmood
    Let's pretend I am going to work on an enterprise application. Say I have 11 modules in the application and I would have to develop Dashboards for every role in the organization for whom I are going to develop application. We Decided to use Asp.Net Web Api and return json data from our apis. We are going to include 11 Self hosted web apis projects in our application (one self hosted web api) for every module. All 11 modules are connected to one Sql server 2012 Database. Then once api is ready we would have to create Business Dashboards (Based upon roles in Organization). So Now my web api client is Asp.Net Mvc application.Asp.Net mvc will consume those web apis. Here is the part for whom all explanation is done. How should I manage Security of all 11 self hosted web apis? How should I only authenticated request is coming? If I authenticate user by login and password and then redirect user to appropriate Dashboard designed for the role that user have and load data by consuming web apis. How should I ensure that the request coming for accessing data is authenticated?

    Read the article

  • ArrayList throwing exception on retrieval from google datastore (with gwt, java)

    - by sumeet
    I'm using Google Web Toolkit with java and google datastore as database. The entity class has arraylist and on trying to retrieve the data from data base I'm getting the exception: Type 'org.datanucleus.sco.backed.ArrayList' was not included in the set of types which can be serialized by this SerializationPolicy or its Class object could not be loaded. For security purposes, this type will not be serialized. I'm using JPA. Entity code: package com.ver2.DY.client; import java.io.Serializable; import java.util.ArrayList; import javax.jdo.annotations.IdGeneratorStrategy; import javax.jdo.annotations.PersistenceCapable; import javax.jdo.annotations.Persistent; import javax.jdo.annotations.PrimaryKey; import com.google.gwt.user.client.rpc.IsSerializable; @PersistenceCapable public class ChatInfo implements Serializable, IsSerializable{ @PrimaryKey @Persistent(valueStrategy = IdGeneratorStrategy.IDENTITY) private Long topicId; @Persistent private String chatTopic; @Persistent private ArrayList messages = new ArrayList(); @Persistent private boolean isFirstPost; public ChatInfo() { } public Long getTopicId() { return topicId; } public void setTopicId(Long topicId) { this.topicId = topicId; } public String getChatTopic() { return chatTopic; } public void setChatTopic(String chatTopic) { this.chatTopic = chatTopic; } public ArrayList getMessages() { return messages; } public void addMessage(String newMsg) { messages.add(newMsg); } public boolean isFirstPost() { return isFirstPost; } public void setFirstPost(boolean isFirstPost) { this.isFirstPost = isFirstPost; } } Method in db class: @Transactional public ChatInfo[] getAllChat() { PersistenceManager pm = PMF.get().getPersistenceManager(); List chats = null; ChatInfo[] infos = null; String query = "select from " + ChatInfo.class.getName(); try{ chats = (List) pm.newQuery(query).execute(); infos = new ChatInfo[chats.size()]; for(int i=0;i } It is a bit strange because earlier I was able to insert and retrieve the data but it now throwing an exception. On searching the web I could find that I need to convert the Arraylist from some DataNucleus type to java util but not sure how to do that.

    Read the article

  • multi thread apps crashes in release mode

    - by etzarfat
    Hello, I'm using Visual Studio 2008 (programming in c). I've a weird problem I worte a program that has 2 threads that runs simultaneously, a recording thread (using audio card to record into memory) and a translation thread (using a speech engine to recognize the words). when I run my program in debug mode (aka setting a breakpoint in the code) it runs great, however when I run in debug mode or release mode (outside the visual studio enviroment) it crashes and give me the following exception: "Unhandled exception at 0x7c911129 in LowLevel.exe: 0xC0000005: Access violation reading location 0x014c7245." My stack looks: LowLevel.exe!__set_flsgetvalue() Line 256 + 0xc bytes C LowLevel.exe!_isleadbyte_l(int c=4359676, localeinfo_struct * plocinfo=0x00000001) Line 57 C++ 014b00d8() LowLevel.exe!PlayDateOfExam(int option=1) Line 2240 + 0x7 bytes C++ LowLevel.exe!NSCThread(void * arg=0x00000000) Line 1585 + 0xb bytes C++ kernel32.dll!7c80b729() winmm.dll!76b5b294() I uses the following file in my project "nsc.lib" and WinMM.lib" I'm not really familiar with threads I used a sample (which works great) and built on it. I saw a similiar question year on the forum but I didn't really understand the answers since I'm not familiar with with threads. Can someone help me? Thanks

    Read the article

  • Adding a Layout to bottom of the screen inside a ScrollView in Landscape mode

    - by andreea
    I have the following layout which works in Portrait mode: the Layout with the id LinearLayout02 is placed at the bottom of the screen. The problem appears when flipping to Lanscape mode, when the #LinearLayout02 is placed at the top of the screen. The question is how do I position #LinearLayout02 at the bottom of the screen in both Portrait and Landscape mode? (This happens on G1 and Xperia) Thank you The following code is placed inside a ScrollView android:layout_height="fill_parent" android:layout_width="fill_parent" android:fillViewport="true" <LinearLayout android:id="@+id/sLayout" android:layout_height="wrap_content" android:layout_width="fill_parent" android:orientation="vertical" android:paddingTop="2dip" android:layout_alignParentTop="true" android:gravity="top" > ..... </LinearLayout> <LinearLayout android:id="@+id/LinearLayout02" android:background="@drawable/bottombar_bg" android:layout_width="fill_parent" android:paddingTop="10dip" android:layout_height="56dip" android:layout_alignParentBottom="true" android:gravity="bottom" > <Button android:id="@+id/navigate" style="@style/mainBottomTabsButtonNormal" android:drawableLeft="@drawable/icon_navigation" android:text="@string/navigationSettings" android:layout_gravity="left"> </Button> <Button android:id="@+id/search" style="@style/mainBottomTabsButtonActive" android:drawableLeft="@drawable/icon_search" android:text="@string/search.label" android:layout_gravity="right"> </Button> </LinearLayout> </RelativeLayout>

    Read the article

  • UINavigationController navigation stack problems in Landscape Mode

    - by David F
    I have a iPhone application that I am currently converting to a Universal Binary to work with the iPad. I have successfully implemented everything I need in terms of layout so that full landscape functionality is now supported in my app (previously I primarily used portrait mode to display content). But, I have one strange problem, and it ONLY occurs in landscape mode: when I push a view controller onto the stack, it takes two taps on the back button to return to the previous view controller!!! The first tap shows a blank view, but with the same name on the left-side back navigation button, the second tap takes the controller back to previous view like it should. I don't have an iPad to test, so I am relying on the simulator. The problem does not show up on the iPhone and doesn't show up if you rotate back to portrait mode. My app consists of a tabbarcontroller with navigation controllers loaded for its vc's: //application delegate - (void)applicationDidFinishLaunching:(UIApplication *)application //.... WebHelpViewController *vc8 = [[WebHelpViewController alloc] init]; UINavigationController *nv8 = [[UINavigationController alloc] initWithRootViewController:vc8]; [self.tabBarController setViewControllers:[NSArray arrayWithObjects:nv1,nv2,nv3,nv4,nv5,nv6,nv7,nv8,nil]]; To implement landscape capability, the UITabBarController is overridden to autorotate when required: //CustomTabBarController.m - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { return [[(UINavigationController *)self.selectedViewController topViewController] shouldAutorotateToInterfaceOrientation:interfaceOrientation]; } ... works fine. I navigate into new views using this method SomeViewController *vc = [[SomeViewController alloc] init]; [self.navigationController pushViewController:vc animated:YES]; [vc release]; Has anyone encountered this problem, and do they know if it's only a simulation error?

    Read the article

  • problems with Console.SetOut in Release Mode?

    - by Matt Jacobsen
    i have a bunch of Console.WriteLines in my code that I can observe at runtime. I communicate with a native library that I also wrote. I'd like to stick some printf's in the native library and observe them too. I don't see them at runtime however. I've created a convoluted hello world app to demonstrate my problem. When the app runs, I can debug into the native library and see that the hello world is called. The output never lands in the textwriter though. Note that if the same code is run as a console app then everything works fine. C#: [DllImport("native.dll")] static extern void Test(); StreamWriter writer; public Form1() { InitializeComponent(); writer = new StreamWriter(@"c:\output.txt"); writer.AutoFlush = true; System.Console.SetOut(writer); } private void button1_Click(object sender, EventArgs e) { Test(); } and the native part: __declspec(dllexport) void Test() { printf("Hello World"); } Update: hamishmcn below started talking about debug/release builds. I removed the native call in the above button1_click method and just replaced it with a standard Console.WriteLine .net call. When I compiled and ran this in debug mode the messages were redirected to the output file. When I switched to release mode however the calls weren't redirected. Console redirection only seems to work in debug mode. How do I get around this?

    Read the article

  • Ruby on Rails App not starting in production mode

    - by Ermin
    Everything works fine in development mode, but when I try to start my app in production mode (RAILS_ENV=production script/server) I get the following error: /opt/ruby1.8/lib/ruby/gems/1.8/gems/searchlogic-2.4.19/lib/searchlogic/named_scopes/conditions.rb:81:in `method_missing': protected method `scope' called for #<Class:0x7f41de524410> (NoMethodError) from /opt/ruby1.8/lib/ruby/gems/1.8/gems/searchlogic-2.4.19/lib/searchlogic/named_scopes/association_conditions.rb:19:in `method_missing' from /opt/ruby1.8/lib/ruby/gems/1.8/gems/searchlogic-2.4.19/lib/searchlogic/named_scopes/association_ordering.rb:27:in `method_missing' from /opt/ruby1.8/lib/ruby/gems/1.8/gems/searchlogic-2.4.19/lib/searchlogic/named_scopes/ordering.rb:30:in `method_missing' from /opt/ruby1.8/lib/ruby/gems/1.8/gems/searchlogic-2.4.19/lib/searchlogic/named_scopes/or_conditions.rb:28:in `method_missing' from /opt/ruby1.8/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/base.rb:1959:in `method_missing_without_paginate' from /opt/ruby1.8/lib/ruby/gems/1.8/gems/will_paginate-2.3.12/lib/will_paginate/finder.rb:170:in `method_missing' from /opt/ruby1.8/lib/ruby/gems/1.8/gems/acts_as_commentable-3.0.0/lib/comment_methods.rb:12:in `included' from .../app/models/comment.rb:2:in `include' from .../app/models/comment.rb:2 from /opt/ruby1.8/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `gem_original_require' from /opt/ruby1.8/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `require'... Now it seems to me it that the acts_as_commentable gem is causing this. But how come, it works fine in development mode.

    Read the article

  • Setting White balance and Exposure mode for iphone camera + enum default

    - by Spectravideo328
    I am using the back camera of an iphone4 and doing the standard and lengthy process of creating an AVCaptureSession and adding to it an AVCaptureDevice. Before attaching the AvCaptureDeviceInput of that camera to the session, I am testing my understanding of white balance and exposure, so I am trying this: [self.theCaptureDevice lockForConfiguration:nil]; [self.theCaptureDevice setWhiteBalanceMode:AVCaptureWhiteBalanceModeLocked]; [self.theCaptureDevice setExposureMode:AVCaptureExposureModeContinuousAutoExposure]; [self.theCaptureDevice unlockForConfiguration]; 1- Given that the various options for white balance mode are in an enum, I would have thought that the default is always zero since the enum Typedef variable was never assigned a value. I am finding out, if I breakpoint and po the values in the debugger, that the default white balance mode is actually set to 2. Unfortunately, the header files of AVCaptureDevice does not say what the default are for the different camera setting. 2- This might sound silly, but can I assume that once I stop the app, that all settings for whitebalance, exposure mode, will go back to their default. So that if I start another app right after, the camera device is not somehow stuck on those "hardware settings".

    Read the article

  • Problem when use compiled .A with simulator mode

    - by Paska
    Hi all, i have a lib .a that run only in device mode. My sdk vers is 4.2 with xcode 3.2.x. In simulator, compile correctle with no warning and no errors, but in run mode (simulator) it crash with this error: Detected an attempt to call a symbol in system libraries that is not present on the iPhone: strtod$UNIX2003 called from function pj_init in image MyAPP. If you are encountering this problem running a simulator binary within gdb, make sure you 'set start-with-shell off' first Program received signal: “SIGABRT”. I try to clean, rebuild and set "set start-with-shell off" from terminal in this way: cd ~ echo '' >> .gdbinit echo 'set start-with-shell 0' >> .gdbinit Restarted all, but nothing. The problem don't wont to resolve! Is there any tag or property that i forgotted to set in the options? In other linker flag is there only "-ObjC". It's very important to solve this issue... any idea please? thanks, A EDIT: It's my lib, compiled in simulator mode! EDIT: It run only with Simulator 4.1. Don't work with iphone 4.0, 4.2 and ipad 3.2 (all simulator).

    Read the article

  • Kernel Mode Rootkit

    - by Pajarito
    On the other 3 computers in my family, I believe that we have a kernel-mode rootkit for windows. It appears that the same rootkit is on all of them. We think. We changed all the important passwords from my computer, running linux right now. On all of the infected computers is Symantic Endpoint Protection, because it's free from the university where my mom and dad work. In my opinion symantec is a piece of crap, seeing as it didn't even manager to delete the tracking cookies it found when I tried it on my own computer. The Computers and their set-ups: Computer A: Vista Business; symantec antivirus. runs it as admin, no password. IE8. no other security software other than what comes with windows. IE8 security settings the default Computer B: XP Home Premium; symantec antivirus. runs as normal user, no password, admin account with weak password, spybot, uses IE8 with default settings, sometimes Firefox Computer C: XP Home Premium; symantec antivirus. runs as normal user, no password, admin account with weak password, uses IE8 with default settings, no other security programs except what came with windows This is what's happening. Cut and pasted from my dad's forum post. -- When I scanned my laptop (Dell XPS M1330 with Windows Vista Small Business), Symantec Endpoint Protection hangs for a while, perhaps 10 seconds or so, on some of the following files 9129837.exe, hide_evr2.sys, VirusRemoval.vbs, NewVirusRemoval.vbs, dll.dll, alsmt.ext, and _epnt.sys. It does this if a run a scan that I set up to run on a new thumbnail drive and it does this even if the thumbnail is not plugged in. It doesn't seem to do this if I scan only the C: drive. I've check for problems with symantec endpoint protection and also with Microsoft Security Essentials and Malwarebytes Anti-Malware. They found nothing and I can't find anything by searching for hidden files. Next I tried microsoft's rootkitrevealer. It (rootkitrevealer) finds 279660 (or so) discrepancies and the interface is so glitchy after that I can't really figure out what is going on. The screen is squirrely. The rootkitrevealer pulls up many files in the folder \programdata\applicationdata and there are numberous appended \applicationdata on the end of that as well. -- As you can see, what we did was install MSE and MBAM and scan with both of them. Nothing but a tracking cookie. Then I took over and ran rootkitrevealer.exe from MicroSoft from a flash drive. It found a bunch of discrepancies, but only about 20 or so where security related, the rest being files that you just couldn't see from Windows Explorer. I couldn't see whether of not the files list above, the ones that the scan was hanging on, where in the list. The other thing is, I have no idea what to do about the things the scan comes up with. Then we checked the other computers and they do the same thing when you scan with Symantec. The people at the university seen to think that dad might not have a virus, but 2 of the computers slowed down noticably AND IE8 started acting all funny. None of my family is very computer oriented, and 2 of the possible causes for the rootkit are: -My dad bought a new flash drive, which shipped with a data security executable on it -My dad has to download lots of articles for his work Those are the only things that stand out, but it could have been anything. We are currently backing up our data, and I'll post again after trying IceSword 1.22. I just looked at my dad's forum topic, and someone recommended GMER. I'll try that too.

    Read the article

  • OpenVPN on ec2 bridged mode connects but no Ping, DNS or forwarding

    - by michael
    I am trying to use OpenVPN to access the internet over a secure connection. I have openVPN configured and running on Amazon EC2 in bridge mode with client certs. I can successfully connect from the client, but I cannot get access to the internet or ping anything from the client I checked the following and everything seems to shows a successful connection between the vpn client/server and UDP traffic on 1194 [server] sudo tcpdump -i eth0 udp port 1194 (shows UDP traffic after establishing connection) [server] sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] sudo iptables -L -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- ip-W-X-Y-0.us-west-1.compute.internal/24 anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] openvpn.log Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 [localhost] Inactivity timeout (--ping-restart), restarting Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 SIGUSR1[soft,ping-restart] received, client-instance restarting Wed Oct 19 03:41:31 2011 MULTI: multi_create_instance called Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Re-using SSL/TLS context Wed Oct 19 03:41:31 2011 a.b.c.d:57889 LZO compression initialized Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Control Channel MTU parms [ L:1574 D:166 EF:66 EB:0 ET:0 EL:0 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Local Options hash (VER=V4): '360696c5' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Expected Remote Options hash (VER=V4): '13a273ba' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 TLS: Initial packet from [AF_INET]a.b.c.d:57889, sid=dd886604 ab6ebb38 Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=EXAMPLE_CA/[email protected] Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=localhost/[email protected] Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Oct 19 03:41:37 2011 a.b.c.d:57889 [localhost] Peer Connection Initiated with [AF_INET]a.b.c.d:57889 Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 PUSH: Received control message: 'PUSH_REQUEST' Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 SENT CONTROL [localhost]: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route-gateway W.X.Y.Z,ping 10,ping-restart 120,ifconfig W.X.Y.Z 255.255.255.0' (status=1) Wed Oct 19 03:41:40 2011 localhost/a.b.c.d:57889 MULTI: Learn: (IPV6) -> localhost/a.b.c.d:57889 [client] tracert google.com Tracing route to google.com [74.125.71.104] over a maximum of 30 hops: 1 347 ms 349 ms 348 ms PC [w.X.Y.Z] 2 * * * Request timed out. I can also successfully ping the server IP address from the client, and ping google.com from an SSH shell on the server. What am I doing wrong? Here is my config (Note: W.X.Y.Z == amazon EC2 private ipaddress) bridge config on br0 ifconfig eth0 0.0.0.0 promisc up brctl addbr br0 brctl addif br0 eth0 ifconfig br0 W.X.Y.X netmask 255.255.255.0 broadcast W.X.Y.255 up route add default gw W.X.Y.1 br0 /etc/openvpn/server.conf (from https://help.ubuntu.com/10.04/serverguide/C/openvpn.html) local W.X.Y.Z dev tap0 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" ;server W.X.Y.0 255.255.255.0 server-bridge W.X.Y.Z 255.255.255.0 W.X.Y.105 W.X.Y.200 ;push "route W.X.Y.0 255.255.255.0" push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" tls-auth ta.key 0 # This file is secret user nobody group nogroup log-append openvpn.log iptables config sudo iptables -A INPUT -i tap0 -j ACCEPT sudo iptables -A INPUT -i br0 -j ACCEPT sudo iptables -A FORWARD -i br0 -j ACCEPT sudo iptables -t nat -A POSTROUTING -s W.X.Y.0/24 -o eth0 -j MASQUERADE echo 1 > /proc/sys/net/ipv4/ip_forward Routing Tables added route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface W.X.Y.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 0.0.0.0 W.X.Y.1 0.0.0.0 UG 0 0 0 br0 C:>route print =========================================================================== Interface List 32...00 ff ac d6 f7 04 ......TAP-Win32 Adapter V9 15...00 14 d1 e9 57 49 ......Microsoft Virtual WiFi Miniport Adapter #2 14...00 14 d1 e9 57 49 ......Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Net work Adapter 10...00 1f d0 50 1b ca ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 17...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 18...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 36...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.2.1 10.1.2.201 25 10.1.2.0 255.255.255.0 On-link 10.1.2.201 281 10.1.2.201 255.255.255.255 On-link 10.1.2.201 281 10.1.2.255 255.255.255.255 On-link 10.1.2.201 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.2.201 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.2.201 281 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.1.2.1 Default =========================================================================== C:>tracert google.com Tracing route to google.com [74.125.71.147] over a maximum of 30 hops: 1 344 ms 345 ms 343 ms PC [W.X.Y.221] 2 * * * Request timed out.

    Read the article

  • How can I prevent an app from leaving full screen mode when I move the cursor to another display?

    - by dan
    When I have dual displays set up, or when I am using Synergy to use one keyboard and mouse across two computers/screens, I can't seem to retain F11 full screen mode for the top application when I mouse out of that screen. This applies to both the application and also to any Flash video that may be playing in full screen mode. Is there any way to retain full screen mode and mouse out of the display?

    Read the article

  • Ubuntu won't display netbook's native resolution

    - by Daniel
    FYI: My Netbook model is HP Mini 210-1004sa, which comes with Intel Graphics Media Accelerator 3150, and has a display 10.1" Active Matrix Colour TFT 1024 x 600. I recently removed Windows 7 Starter from my netbook, and replaced it with Ubuntu 12.10. The problem is the OS doesn't seem to recognise the native display resolution of 1024x600 i.e. the bottom bits of Ubuntu is hidden beneath the screen & the only 2 available resolutions are: the default 1024x768 and 800x600. I've also thought about replacing Ubuntu with Lubuntu or Puppy Linux, as the system does run a bit slow, but I can't, as then I won't be able to access the taskbar and application menu which will be hidden beneath the screen. Only Ubuntu with Unity is currently usable, as the Unity Launcher is visible enough. I was able to define a custom resolution 1024x600 using the Q&A: How set my monitor resolution? but when I set that resolution, there appears a black band at the top of the screen and the desktop area is lowered, with bits of it hidden beneath the screen. I tried leaving it at this new resolution and restarting the system to see if the black band would disappear & the display will fit correctly, but it gets reset to 1024x768 at startup and displays following error: Could not apply the stored configuration for monitors none of the selected modes were compatible with the possible modes: Trying modes for CRTC 63 CRTC 63: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 0) CRTC 63: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 0) CRTC 63: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 0) CRTC 63: trying mode 1024x768@60Hz with output at 1024x600@60Hz (pass 1) CRTC 63: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 1) CRTC 63: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 1) CRTC 63: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 1) Trying modes for CRTC 64 CRTC 64: trying mode 1024x768@60Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 1024x768@60Hz with output at 1024x600@60Hz (pass 1) CRTC 64: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 1) CRTC 64: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 1) CRTC 64: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 1)

    Read the article

  • cannot mount root filesystem on 10.04

    - by howaryoo
    I tried to apply the recommendation of question: Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) After running that command: sudo mount --bind /dev /mnt/dev I get this error message: mount: mount point /mnt/dev does not exist fdisk -l returns /dev/sda1 /dev/sda2 /dev/sda5 do I need to mount sda2 and sda5? Edited after @psusi's comment: /dev/sda1 is the boot file system It seems that I need to mount sda2 or sda5. Here is what I tried: (I tried this on a virtual machine so the sda(s) are now vda(s) ) ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/vda: 19.3 GB, 19327352832 bytes 16 heads, 63 sectors/track, 37449 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0008eece Device Boot Start End Blocks Id System /dev/vda1 * 3 496 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/vda2 498 37448 18622465 5 Extended Partition 2 does not end on cylinder boundary. /dev/vda5 498 37448 18622464 8e Linux LVM ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ sudo mount -t ext4 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ sudo mount -t ext2 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ Any info that can help me rescue that server would be greatly appreciated!

    Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >