Search Results

Search found 40422 results on 1617 pages for 'source control'.

Page 648/1617 | < Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• How to Upgrade PHP 5.2 to 5.3 on Windows Plesk Panel 8.2

  - by Jagat Sheth

  I need to upgrade my server PHP version becasue of Wordpress New version not support PHP 5.2. On My server windows 2003 stansard edition x64 with SP1 installed, IIS 6.0, MySQL 4.1, Plesk Panel 8.2. I have follow listed steps on plesk KB. http://kb.parallels.com/6670 How to update PHP 5 on a Windows server with Parallels Plesk Control Panel 8.x and 9.x installed. In order to upgrade PHP 5 to the necessary version (other than shipped with Parallels Plesk), please perform the following steps: Stop Plesk services (‘Control Panel’ and all that are included in the ‘Plesk Run-Time’ section) Rename folder %plesk_dir%\Additional\PleskPHP5 to the orig_PleskPHP5 Create a new folder %plesk_dir%\Additional\PleskPHP5 Download necessary version of PHP, unzip its content, and copy it to the newly created folder PleskPHP5 Copy the file php.ini from the old folder orig_PleskPHP5 to the new one Make sure the permissions are inherited Start Plesk services Click the "Refresh" button in the Components Management section in Parallels Plesk Panel and check if you can see the new PHP version there After follow steps when I open a PHP info it shows me specified module could not be found. If anybody know solution Kindly help me is highly priority. I am very thankful if any one help me to solve this ASAP. Thanks and regards, Jagat Sheth

  Read the article

• iptables drops some packets on port 80 and i don't know the cause.

  - by Janning

  Hi, We are running a firewall with iptables on our Debian Lenny system. I show you only the relevant entries of our firewall. Chain INPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW Chain OUTPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Some packets get dropped each day with log messages like this: Feb 5 15:11:02 host1 kernel: [104332.409003] dropped IN= OUT=eth0 SRC= DST= LEN=1420 TOS=0x00 PREC=0x00 TTL=64 ID=18576 DF PROTO=TCP SPT=80 DPT=59327 WINDOW=54 RES=0x00 ACK URGP=0 for privacy reasons I replaced IP Addresses with and This is no reason for any concern, but I just want to understand what's happening. The web server tries to send a packet to the client, but the firewall somehow came to the conclusion that this packet is "UNRELATED" to any prior traffic. I have set a kernel parameter ip_conntrack_ma to a high enough value to be sure to get all connections tracked by iptables state module: sysctl -w net.ipv4.netfilter.ip_conntrack_max=524288 What's funny about that is I get one connection drop every 20 minutes: 06:34:54 droppedIN= 06:52:10 droppedIN= 07:10:48 droppedIN= 07:30:55 droppedIN= 07:51:29 droppedIN= 08:10:47 droppedIN= 08:31:00 droppedIN= 08:50:52 droppedIN= 09:10:50 droppedIN= 09:30:52 droppedIN= 09:50:49 droppedIN= 10:11:00 droppedIN= 10:30:50 droppedIN= 10:50:56 droppedIN= 11:10:53 droppedIN= 11:31:00 droppedIN= 11:50:49 droppedIN= 12:10:49 droppedIN= 12:30:50 droppedIN= 12:50:51 droppedIN= 13:10:49 droppedIN= 13:30:57 droppedIN= 13:51:01 droppedIN= 14:11:12 droppedIN= 14:31:32 droppedIN= 14:50:59 droppedIN= 15:11:02 droppedIN= That's from today, but on other days it looks like this, too (sometimes the rate varies). What might be the reason? Any help is greatly appreciated. kind regards Janning

  Read the article

• How to use a common library of environment variables among different languages?

  - by JDS

  We have three main languages with which we perform system tasks: Bash, Ruby, and PHP, and Perl. Four, four main languages. We use managed environment variables to provide authorization info that automated scripts need. For example, a mysql user account and password. We'd like to use one single managed file to maintain these variables. In some instances, for example, in cron, these environment variables are not available. They are made available in CLI scripts because we source the env file in everyone's profile. But something like cron doesn't do that. On the CLI, when the env file is sourced, any given script can access those variables. Bash has them directly, PHP in $_ENV, ruby in ENV, etc. We can't source the file into non-Bash scripts, because most languages implement shell commands by running them in a subshell. We considered parsing the Bash, converting to the script's lang, and running the equivalent of "exec(parsed_output)" on the resulting strings. What is a good solution to providing managed environment vars to scripts running in cron, or similar?

  Read the article

• How do you avoid that server documentation gets out of sync with the actual setup?

  - by Frerich Raabe

  I'm a hobbyist maintaining a small FreeBSD server serving mail via IMAP - it's an exercise in server administration. The setup does have reasonably good documentation (in AsciiDoc format) which recently allowed another person to recreate the entire setup from scratch in less than 30 minutes. However, I noticed that after the initial setup, it easily happens that small changes done to the system (say: inetd gets disabbled, my IMAP server listens on an additional port for ManageSieve connections, a new router is added to the exim configuration) don't end up in the documentation immediately (if at all). My idea was to avoid this problem by (partially?) generating the documentation out of the configuration files and the comments therein - one way to implement this may be to put /etc and /usr/local/etc into some source code management system (say - git) and then run a script which regenerates the documentation on every commit. However, I'm not sure whether that would be overkill and/or too difficult to get right (after all, I don't want complete copies of the source files in my documentation but rather just the diffs). How do other people avoid that the server documentation gets outdated - is there a good way to keep them in sync automatically, or do you just have the discipline to update the documentation the same time you modify the system?

  Read the article

• IIS6 site using integrated authentication (NTLM) fails when accessed with Win7 / IE8

  - by Ciove

  Hi, I'm having pretty similar problems as described in case 139099, but the fix there doesn't seem to work for me. Here's the details: Server: Win2003Srv R2 SP2 (stadalone, not a member of a domain). IIS6, TCP/443 (https). Anonymous access disabled. Integrated Windows authentication enabled. Local useraccouts Each useraccount has own virtual folder with change access and read access to site root. The 'adsutil NTAuthenticationProviders "NTLM"' -thing set to site root and useraccount's virtual folder. Client: Win7 Enterprise Member of a AD-Domain IE8 Allows three login attepts then fails. Using [webservername][username] in the logon window (Windows security) Logon using other browsers (Chrome and Firefox) works OK. The Web services log shows one 401.2 and two 401.1 events. The Security Event log shows two events, first is Fauilure Audit (680), The second event is Fauilure Audit (529) with these details: Logon Failure: Reason: Unknown user name or bad password User Name: [username] Domain: [webservername] Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: [MyWorkstation] Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: [999.999.999.999] Source Port: 20089 Any ideas appreciated.

  Read the article

• Port(s) not forwarding?

  - by user11189

  I have cable internet service through Charter Communications and feed two desktop computers through a Linksys RP614v3 router. One system is my wife's running WinXP Home Edition and the other is mine, running Vista Home Premium (sp1). I have port forwarding configured in the Linksys so I can access the Vista system remotely using TightVNC. Initially, it worked great and I was able to remotely tend email and access local files while out of town for work. Lately, the cable internet service appears to flicker intermittently and upon return, my Mailwasher program loses ability to access the net and I've been unable to make the remote connection. When I reset the port forwarded for email in the router control panel, Mailwasher functionality returns but as I'm home when that happens, I have no easy way to check remote access until the next time I'm on the road or at work. I'm at my wit's end -- the TightVNC client accesses fine from my wife's system from behind the modem/router setup but I don't know how to maintain whatever gets reset when I fiddle with the control panel and the need to do so at all is new. I accessed it fine for a week off and on while out of town a month ago and now I can't leave home and access it from work an hour later.

  Read the article

• Make a drive from one machine appear as a physical disk in another machine.

  - by Roberto Sebestyen

  I want to take a physical disk (or part of a disk) in one machine (call it machine-A) and I want to make it available in another machine (machine-B). But I don't want to map a network drive. I want it to appear in machine-B as a physical drive. Even though it is not a physical drive. The reason I want to do this is i want the ability to create shares in machine-B on that drive. Since I cannot do that on mapped drives, I need to use some utility that fools machine-B to think that it is a physical drive, and treat it as such. Both of these machines are windows server 2003. I heard about NFS, It sounds like what could be the solution to my problem. But isn't that a Linux/Unix protocol? What tools can I use to make this happen? Are there any open source solutions? I don't care what the solution is, as long as it achieves the end result, preferably open source solution though. Thanks for reading guys and gals!

  Read the article

• Permanent solution to Win XP SP3 window animation removal

  - by epale85

  Hello everyone, May I know how I can get rid of the Window Animation (seen when you minimise or maximise a window) in Windows XP Service Pack 3 Permanently?? I have tried the following two solutions: I went to the control panel---adjust visual effects--- then unchecked the "Animate windows when maximising and minimising" option. 2.I have tried using windows powertoys tweakUI to disable the animation. 3.I even tried this: Turn Off Window Animation You can shut off the animation displayed when you minimize and maximize Windows. 1. Open RegEdit 2. Go to HKEY_CURRENT_USER\Control panel \Desktop\ WindowMetrics 3. Create a new string value "MinAnimate". 4. Set the value data of 0 for Off or 1 for On But still no help The Big Problem is that the window animation will disappear for a while but returns again some time later. When I navigate back to the "adjust visual effects" window, the checkbox for "Animate windows when maximising and minimising" is checked again. Thank you very much

  Read the article

• How to get just value from database query in Excel?

  - by Corin

  I'm creating a spreadsheet as a collection point of information from a number of MS Access databases. I will run a query on each database to get a count of records in a particular table. Each database has the same structure but different content as they are used in different situations. So the query returns a single value, rec_count. I've figured out how to create that query, save it and then use it as the data source. So far so good. The problem is that Excel treats the query results as a table. So instead of getting just the single value the query returns, I also get the field name. Thus the result takes up two cells instead of one. When linking in the data source, I only see Table, PivotTable Report and PivotChart as options for viewing the data. I don't want any of those. I just want the single value without any formatting, column headers, etc. Is there a way to do this is Excel 2007?

  Read the article

• Formal separation marker of syslog events?

  - by Server Horror

  I've been looking at RFC5424 to find the formally specified marker that will end a syslog event. Unfortunately I couldn't find it. So If I wanted to implement some small syslog server that reacts on certain messages what is the marker that ends a message (yes commonly an event is a single line, but I just couldn't find it in the specification) Clarification: I call it event because I associate a message with a single line. An event could possibly be some thing like Type: foo Source: webservers whereas a message to me is this: Type: foo Source: webservers http://tools.ietf.org/html/rfc5424#section-6 defines: SYSLOG-MSG = HEADER SP STRUCTURED-DATA [SP MSG] neither STRUCTURED-DATA nor MSG tell me how these fields end. Especially MSG is defined as as MSG-ANY / MSG-UTF8 which expands to virtually anything. There's nothing that says a newline marks the end (or an 8 or an a for that matter). Given the example messages (section 6.5): This is one valid message, or 2 valid messages depending on wether you say that a HEADER element must never occur in any MSG element: literal whitespace <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 - <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 | is this an end marker? \t stands for a tab <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 -\t<34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 | is this an end marker? \n stands for a newline <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 -\n<34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 | is this an end marker? Either I'm misreading the RFC or there just isn't any mention. The sizes specified in the RFC just say what the minimum length is expected that I can work with...

  Read the article

• deploy git project and permission issue

  - by nixer

  I have project hosted with gitolite on my own server, and I would like to deploy the whole project from gitolite bare repository to apache accessible place, by post-receive hook. I have next hook content echo "starting deploy..." WWW_ROOT="/var/www_virt.hosting/domain_name/htdocs/" GIT_WORK_TREE=$WWW_ROOT git checkout -f exec chmod -R 750 $WWW_ROOT exec chown -R www-data:www-data $WWW_ROOT echo "finished" hook can't be finished without any error message. chmod: changing permissions of `/var/www_virt.hosting/domain_name/file_name': Operation not permitted means that git has no enough right to make it. The git source path is /var/lib/gitolite/project.git/, which is owned by gitolite:gitolite And with this permissions redmine (been working under www-data user) can't achieve git repository to fetch all changes The whole project should be placed here: /var/www_virt.hosting/domain_name/htdocs/, which is owned by www-data:www-data. What changes I should do, to work properly post-receive hook in git, and redmine with repository ? what I did, is: # id www-data uid=33(www-data) gid=33(www-data) groups=33(www-data),119(gitolite) # id gitolite uid=110(gitolite) gid=119(gitolite) groups=119(gitolite),33(www-data) does not helped. I want to have no any problem to work apache (to view project), redmine to read source files for project (under git) and git (doing deploy to www-data accessible path) what should I do ?

  Read the article

• How to find the IP Address of a vm running on VMware (or other methods of using VM)

  - by sixtyfootersdude

  I am running VMware Workstation on a Linux box. When I power on a centOS (Linux) virtual machine I cannot get mouse or keyboard control of the machine. I suspect that it has something to do with the error message: You do not have VMware Tools installed in this guest. Chose "Install VMware Tools" from the VM menu. If I click on that menu option it inserts a virtual cd with drivers etc. This does not help me since I don't have keyboard or mouse control over the machine. I was thinking that if I could figure out the IP address or hostname I could use any number of protocols to get into the machine (SSH comes to mind). How can I get the IP address or hostname of this machine? Note: I did not create this machine. A coworker created it who is no longer with the company. Would save me a lot of time if I could get into the machine. I have login credentials so that won't be a problem.

  Read the article

• Windows 7 mouse multi selection on windows explorer with CTRL and point to select / single click to open

  - by bortao

  This is something that have annoyed me since i changed to Windows 7. I don't do double click for a long time now since windows introduced 1 click selection (Folder Options Click items as follows Single click to open an item). The problem is, when i click Control and hover over the items, they select/deselect automatically every small amount of mouse movement i make. What i want is to select/deselect the items only when i enter/exit them. So to deselect an item im hovering, i have to move the mouse out of it, and then back in. I'm using Intellimouse Explorer official drivers. (edit) Here's another related annoyance: When you are hovering something and move the mouse inside other item (Holding Ctrl) The new item may or may not be selected. If you continue moving the mouse it gets selected/deselected as you move. (more edit) I have found that the parameter HKCU\Control Panel\Mouse\MouseHoverHeight / MouseHoverWidth have some influence here. If it's set to 2, the item select/deselect really quickly as you move the mouse. When set to larger numbers, its slower. But setting to 20 or 200 don't seem to be much different.

  Read the article

• iptables: How to combine DNAT and SNAT to use a secondary IP address?

  - by Que_273

  There are lots of questions on here about iptables DNAT/SNAT setups but I haven't found one that solves my current problem. I have services bound to the IP address of eth0 (e.g. 192.168.0.20) and I also have a IP address on eth0:0 (192.168.0.40) which is shared with another server. Only one server is active, so this alias interface comes and goes depending on which server is active. In order to get traffic accepted by the service a DNAT rule is used to change the destination IP. iptables -t nat -A PREROUTING -d 192.168.0.40 -p udp --dport 7100 -j DNAT --to-destination 192.168.0.20 I also wish all outbound traffic from this service to appear to come from the shared IP, so that return responses will work in the event of a active-standby failover. iptables -t nat -A POSTROUTING -p udp --sport 7100 -j SNAT --to-source 192.168.0.40 My problem is that the SNAT rule is not always run. Inbound traffic causes a connection tracking entry like this. [root]# conntrack -L -p udp udp 17 170 src=192.168.0.185 dst=192.168.0.40 sport=7100 dport=7100 src=192.168.0.20 dst=192.168.0.185 sport=7100 dport=7100 [ASSURED] mark=0 secmark=0 use=2 which means the POSTROUTING chain is not run and outbound traffic leaves with the real IP address as the source. I am thinking I can set up a NOTRACK rule in the raw table to prevent conntracking for this port number, but is there a better or more efficient way to make this work? Edit - Alternative question: Is there a way (in CentOS/Linux) to have an interface that can be bound to but not used, such that it can be attached to the network or detached when a shared IP address is swapped between servers?

  Read the article

• How do I connect remotely to SQL Server from Windows client?

  - by humble_coder

  Hi All, Having a bit of an issue connecting to SQL SERVER remotely from Windows. I've verified that all of my settings are correct via SQL SERVER MANAGEMENT STUDIO EXPRESS and SQL SERVER CONFIGURATION MANAGER. I can connect remotely using ODBC drivers from other OSes (e.g. OS X, Linux, etc). However, when I connect with the same credentials from a remote Windows machine using "SQL SERVER" as the driver I am told that the system cannot connect. I've tried creating an ODBC Data Source and I get the same error: Connection failed: SQLState: '01000' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]ConnectionOpen(InvalidInstance()). Connection failed: SQLState: '08001' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]Invalid Connection From the non-windows machines I can use the IP address of the SQL Server just fine. However, on the remote Windows machine, neither IP address nor named instance works. FYI, I can create an ODBC Data Source using the named instance on the machine actually running the SQL Server (but this is, of course, nothing special -- just proof that it isn't completely hosed). One interesting note: If I use SQL STUDIO 2005 from a Windows client machine, I can use the IP address to connect remotely. Still, the whole reason I bring this up is because I need to use a software package I've written to connect to SQL Server remotely from Windows machines as well. Previously the solution was only needed to xfer data from SQL Server into a PostGRES or MySQL database on non-Windows machines (due to DBA preference). However, now they also want to move the data from the legacy software to MySQL even on Windows. Any assistance would be most appreciated. Feel free to provide a full example connection string. Best

  Read the article

• S3sync not working

  - by user57833

  Hello, I managed to get s3sync to upload my test folder to Amazon S3 and can see it in the MWS Managment Console. Downloading the data back to a test folder results in the following error message: root@mybucketname:/var/s3sync# ./week_download.sh s3Prefix backups/weekly localPrefix /var/s3sync/testdown/weekly s3TreeRecurse mybucketname backups/weekly Creating new connection Trying command list_bucket mybucketname prefix backups/weekly max-keys 200 delimiter / with 100 retries le ft Response code: 200 prefix found: / s3TreeRecurse mybucketname backups/weekly / Trying command list_bucket mybucketname prefix backups/weekly/ max-keys 200 delimiter / with 100 retries l eft Response code: 200 S3 item backups/weekly/ s3 node object init. Name: Path:backups/weekly Size:0 Tag:d41d8cd98f00b204e9800998ecf8427e Date:Fri O ct 29 14:21:53 UTC 2010 local node object init. Name: Path:/var/s3sync/testdown/weekly/ Size: Tag: Date: source: dest: Update node s3sync.rb:638:in initialize': No such file or directory - /var/s3sync/testdown/weekly/.s3syncTemp (E rrno::ENOENT) from s3sync.rb:638:inopen' from s3sync.rb:638:in updateFrom' from s3sync.rb:393:inmain' from s3sync.rb:735 I am using the following download script: !/bin/bash script to download local directory upto s3 cd /var/s3sync/ export AWS_ACCESS_KEY_ID=nothing to see here export AWS_SECRET_ACCESS_KEY=nothing to see here export SSL_CERT_DIR=/var/s3sync/certs ruby s3sync.rb -r -v -d --progress --make-dirs mybucket:backups/weekly /var/s3sync/testdown copy and modify line above for each additional folder to be synced Any idea's? Does the download script need to download to the source of Amazon S3 i.e testup folder? Was hoping on the instance of a complete failure and the original folders won't exist that it would just download everything from me. Note: changed my bucket names to "mybucketname" so that it is not public!

  Read the article

• TCP/UDP hole punching from and to the same NAT network

  - by Luc

  I was wondering if tcp/udp hole punching would still work when you are in the same network (behind a NAT), and what the packet's path would be. What happens when using hole punching on the same network, is that it will send a packet out with the same destination and source address. Only the source and destination port would differ. I imagine a router with NAT loopback enabled will handle this as it should, but how about other routers? Would they drop the packet, or would a router (the first?) from the ISP bounce the packet back after which it gets handled okay? I'm wondering because I was thinking about using this technique to circumvent a block between peers in a network (like a school network where clients can only access the internet, but any contact with each other is blocked). The only other option is to use a man in the middle as proxy (tunnel?). The disadvantage of this is that you have to have a server with significantly more bandwidth than one that would only do hole punching. Also the latency would increase significantly.

  Read the article

• Small maximum number of connections on a Linux router

  - by Eugene

  I have a Linux box acting as a router with no iptables or other firewall and no networking applications running on it, just pure router. I've put it in a test environment that generates many TCP connections, each having unique source and destination IP, and those connections go through this router. I'm observing that number of connections successfully created rise to approximately 500 and then no more connections can be created for several minutes, then another 100 connections can be created and there is another pause, and so on. If 10 connections for each source-destination pair are created, then maximum numbers go about 10 times up, so the problem is probably with many connections from different IPs. As traffic is simply routed, it doesn't have to do with number of file descriptors, iptables connection tracking and other things often proposed to check in similar cases. The box has plenty of free RAM and CPU, both NICs are gigabit. The kernel is 2.6.32. I've already tried increasing net.core.*mem_max, net.core.netdev_max_backlog and txqueuelen on both NICs, with completely no effect. What else should I check ? Is there some rate-limit in the kernel itself ?

  Read the article

• Is domain-transfer inherently safe for downtime when the name servers remain the same?

  - by jlmt

  I've been reading around this topic towards understanding whether there's some or no chance of downtime during an upcoming domain transfer for 15 live and very critical domains. In our case there are three companies involved: CompanyA is the original registrar and DNS host, CompanyB is the new DNS host, and CompanyC is the new registrar. I've already changed the nameservers for all domains to those of CompanyB. We suffered some downtime because CompanyA deleted their hosted DNS for our domains directly after the change, but the changes propagated and we're now able to configure our DNS with CompanyB. From what I understand (please correct where wrong!): There exists an SOA record that points oneofourdomains.com to ns.companyb.com. That record is maintained and authoritatively hosted by the ccTLD registry for the domain (eg. Verisign for .com). CompanyA currently has the ability to change the SOA record because they're the registrar. There exist NS records for oneofourdomains.com, which are also related to the link from domain name to nameserver, are similarly hosted by the ccTLD, and which CompanyA are also able to change while acting as registrar. Neither CompanyB nor CompanyC currently have any control over the SOA or NS records. CompanyA are unable to cause us (DNS) problems during the transfer by dropping service early, because they are not the authoritative source for the SOA and NS records. When we transfer the domains, it's administrative control of the SOA and NS records that will be transferred to CompanyC. As long as we advise CompanyC that the SOA and NS records must not change (as regards pointing to CompanyB's nameservers), there's no need for any kind of DNS change, and therefore no possibility of downtime. Is my understanding of this correct? My fear is that CompanyA will somehow cut us off again, and their support dept hasn't given me much confidence in their understanding of the topic.

  Read the article

• Sound doesn't work anymore after replacing RAM

  - by thejh

  Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

  Read the article

• How to track things that SHOULD happen, but might not have

  - by Kamiel Wanrooij

  I am running into a couple of issues with some applications we've deployed and maintain. I have the feeling we have approached this with some anti-patterns up to now, but I would like to see how to make this more flexible and stable. In one situation, we have a server at a client which pushes data to us to parse every night (yes, Windows Task Scheduler). This is highly unstable however, so once every month this doesn't happen because of reasons out of our control. This heavily impacts our business since we run with stale data in that situation. In another scenario we have a lot of background job processes that should be running. We already keep them up using bluepill ( http://www.github.com/arya/bluepill ) but obviously restarts happen, both automatically and manually, and people forget things or systems mess up. What I would like to track is events that should occur or should be available. Like the existence of a process, the execution of a program, or the creation/age of a file, and track it when they don't happen or exist. We develop most things in Ruby on Rails, use NewRelic, Bluepill and Munin, and run on Ubuntu. I've been toying around with counting ps aux | grep processname | wc -l in Munin scripts, or capturing the age of a file and raising alerts over 24-26 hours, stuff like that. Is there better tooling to track things that should happen, and raise alerts if they don't? P.S. I know some things are suboptimal, like manually having to define bluepill for applications and then forgetting to do so. The same goes for the push based approach of the first application, a dedicated daemon that manages that on the client side that we control and can track its connection to us might be a much better solution.

  Read the article

• Why Are SPF Records Failing?

  - by robobobobo

  Ok I've been going through various different sites, resources and topics here trying to figure out what is wrong with my SPF records but no matter what I do they don't seem to pass. Here's what I have "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" I've tried multiple different tools to check my spf records, some give me a pass, some don't. But I can't send mail to certain google app accounts, they just bounce back all the time which is very annoying. Anyone got any ideas? I have noticed that the source IP address is not the IPV4 addresses I've defined, but Cpanel wouldn't let me add that address into it.. And here's the result of tests I'm getting back from port25.com. I'm running WHM by the way and have enabled spf and dkim. Summary of Results SPF check: fail DomainKeys check: neutral DKIM check: pass Sender-ID check: fail SpamAssassin check: ham Details: HELO hostname: server1.viralbamboo.com Source IP: 2a01:258:f000:6:216:3eff:fe87:9379 mail-from: ###@viralbamboo.com SPF check details: Result: fail (not permitted) ID(s) verified: smtp.mailfrom=###@viralbamboo.com DNS record(s): viralbamboo.com. SPF (no records) viralbamboo.com. 13180 IN TXT "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" viralbamboo.com. AAAA (no records) viralbamboo.com. 13180 IN MX 0 viralbamboo.com. viralbamboo.com. AAAA (no records) DomainKeys check details: Result: neutral (message not signed) ID(s) verified: header.From=###@viralbamboo.com DNS record(s): DKIM check details: Result: pass (matches From: ###@viralbamboo.com). ID(s) verified: header.d=viralbamboo.com Canonicalized Headers: content-type:multipart/alternative;'20'boundary="4783D1BE-5685-41CF-B91B-1F15E91DD1E3"'0D''0A' date:Mon,'20'1'20'Jul'20'2013'20'21:30:47'20'+0000'0D''0A' subject:=?utf-8?Q?test?='0D''0A' to:"[email protected]?="'20''0D''0A' from:=?utf-8?Q?Rob_Boland_-_Viralbamboo?='20'<###@viralbamboo.com'0D''0A' mime-version:1.0'0D''0A' dkim-signature:v=1;'20'a=rsa-sha256;'20'q=dns/txt;'20'c=relaxed/relaxed;'20'd=viralbamboo.com;'20's=default;'20'h=Content-Type:Date:Subject:To:From:MIME-Version;'20'bh=CJMO7HYeyNVGvxttf/JspIMoLUiWNE6nlQUg5WjTGZQ=;'20'b=;

  Read the article

• Constant crashes in windows 7 64bit when playing games

  - by yx.

  I've tried everything I can possibly think of in trying to fix this problem and I'm totally out of ideas, so any help would be appreciated: The problem: whenever I fire up a game, it works for a short while with no problems and then it would crash. Either its a hard crash, forcing me to reboot, or windows would report that the display driver has stopped working and recovered. Here is a list of things I've already tried: Drivers - tried the latest drivers (catalyst 9.12) as well as the stock drivers that came with the video card. Also have the latest BIOS/chipset Memtest - Ran Memtest86+ overnight, had no problems, the windows diagnostic tool also does not find any problems. Overheating - Video card/cpu temperatures are well below peak (42 and 31 Celsius receptively) PSU Voltage - CPUID shows that the voltage levels are all above what they should be. The PSU itself is only roughly 16 months old and is a good model. HDD - No errors when checked GPU - Brand new (replaced previous card since I thought it was the problem, apparently not) Overclocking - Everything is at stock levels, memory voltage is set to manufacturer's standard Specs: Motherboard: ASUS P5Q Pro CPU: Core 2 Duo E8400 3.0 ghz OS: Windows 7 home premium 64 bit Memory: Mushkin Enhanced 4GB DDR2 GPU: Sapphire HD 5850 1GB PSU: SeaSonic M12 600W ATX12V DirectX: DX11 Event Viewer after a crash always has these logged: A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 1 The details view of this entry contains further information. A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 0 The details view of this entry contains further information. A previous card that I had (4850x2) also had these errors, so I changed video cards, but the same thing is happening.

  Read the article

• Empty $upstream_http_location variable if response was cached

  - by Ivaldi

  I would like to cache the response of an redirect. (Cache the request to some site which returns a redirect and cache the second request which returns the actual content.) So far my config looks like this: location = /proxy { error_page 301 302 307 = @redir; resolver 8.8.8.8; proxy_pass $arg_url; proxy_intercept_errors on; proxy_cache pcache; proxy_cache_key $arg_url; proxy_cache_valid 200 301 302 307 1d; proxy_cache_min_uses 1; proxy_ignore_client_abort on; proxy_ignore_headers Set-Cookie Expires Cache-Control; } location @redir { resolver 8.8.8.8; # we need to assign $upstream_http_location to another var in order to use it with proxy_pass set $target $upstream_http_location; proxy_pass $target; proxy_cache predirects; proxy_cache_key $upstream_http_location; proxy_cache_valid 200 301 302 307 1d; proxy_cache_min_uses 1; proxy_ignore_headers Set-Cookie Expires Cache-Control; } It works for the first request or without the 30x codes for proxy_cache_valid in the /proxy part, but $target and $upstream_http_location are empty, if the response was cached. Is there a nice solution to cache both requests? Thanks!

  Read the article

< Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >