Search Results

Search found 2733 results on 110 pages for '02 javafx'.

Page 65/110 | < Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >

• Sound card not detected in 13.04

  - by Ganessh Kumar R P

  I have a problem with my sound card. I don't have volume up or down option anywhere. In the setting -> Sound I don't have any card detected. But when I run the command sudo aplay -l, I get the following output **** List of PLAYBACK Hardware Devices **** Failed to create secure directory (/home/ganessh/.config/pulse): Permission denied card 0: MID [HDA Intel MID], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 And the command lspci -v | grep -A7 -i "audio" outputs 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at f0f20000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode]) -- 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d3efc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 So, I assume that the drivers are properly installed but still I don't get any option in the settings or volume control. The same card used to work well back in 2010 versions(04 and 10) Any help is appreciated. Thanks

  Read the article

• Can't install the wireless driver in HP Pavilion dv2419us

  - by maqtanim

  I've just installed Ubuntu 13.04 in an old HP Pavilion dv2419us. The problem is, Ubuntu doesn't detect the wireless card. But it works fine in Windows 7. The following command returns nothing! lspci -vvnn | grep 14e4 And the lspci output is: 00:00.1 RAM memory: NVIDIA Corporation C51 Memory Controller 0 (rev a2) 00:00.2 RAM memory: NVIDIA Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: NVIDIA Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: NVIDIA Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: NVIDIA Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: NVIDIA Corporation C51 Memory Controller 2 (rev a2) 00:02.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:03.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: NVIDIA Corporation C51 [GeForce Go 6150] (rev a2) 00:09.0 RAM memory: NVIDIA Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: NVIDIA Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: NVIDIA Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: NVIDIA Corporation MCP51 PMU (rev a3) 00:0b.0 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: NVIDIA Corporation MCP51 IDE (rev f1) 00:0e.0 IDE interface: NVIDIA Corporation MCP51 Serial ATA Controller (rev f1) 00:10.0 PCI bridge: NVIDIA Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: NVIDIA Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: NVIDIA Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 05:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 05:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 05:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 05:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) The command lspci -nn | grep 0280 gives no output. Any suggestion regarding this?

  Read the article

• Ubuntu 12.04 - default Radeon driver does not work at all

  - by mumble

  I've recently upgraded to 12.04 LTS and I have an ATI Radeon HD5670. I've heard that the open source 'Radeon' driver is used by default. However, it wasn't showing anything for me. What I did was I added the 'nomodeset' option to boot up and install fglrx. But it didn't work well for me as it introduced a lot of problems (freezes/glitches). So I removed/purged fglrx and am planning to use the open source drivers instead. So my question is this: Why is my default Radeon driver not working? Is anyone having a similar issue? I've also tried using the ubuntu-x-swat driver by running the ff commands: sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update But the result was the same as the Radeon driver. Nothing shows up on system boot. Any ideas? Thanks in advance! Update Running lspci -nn | grep VGA gives me the following: 02:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Redwood [Radeon HD 5670] [1002:68d8]

  Read the article

• VS2012 Coded UI Test closes browser by default

  - by Tarun Arora

  *** Thanks to Steve St. Jean for asking this question and Shubhra Maji for answering this question on the ALM champs list *** 01 – Introduction The default behaviour of coded UI tests running in an Internet Explorer browser has changed between MTM 2010 and MTM 2012. When running a Coded UI test recorded in MTM 2012 or VS 2012 at the end of the test execution the instance of the browser is closed by default. 02 – Description Let’s take an example. As you can see the CloseDinnerNowWeb() method is commented out.  In VS 2010, upon running this test the browser would be left open after the test execution completes. In VS 2012 RTM the behaviour has changed. At the end of the test run, the IE window is closed even though there is no command from the test to do so. In the example below when the test runs, it opens 2 IE windows to the website. When the test run completes both the windows are closed, even though there is no command in the test to close the window. 03 – How to change the CUIT behaviour not to close the IE window after test execution? This change to this functionality in VS 2012 is by design. It is however possible to rollback the behaviour to how it originally was in VS 2010 i.e. the IE window will not close after the test execution unless otherwise commanded by the test to do so. To go back to the original functionality, set BrowserWindow.CloseOnPlaybackCleanup = false More details on the CloseOnPlaybackCleanup property can be found here http://msdn.microsoft.com/en-us/library/microsoft.visualstudio.testtools.uitesting.applicationundertest.closeonplaybackcleanup.aspx  HTH

  Read the article

• Mercurial says "nothing changed", but it did. Sometimes my software is too clever.

  - by user12608033

  It seems I have found a "bug" in Mercurial. It takes a shortcut when checking for differences in tracked files. If the file's size and modification time are unchanged, it assumes its contents are unchanged: $ hg init . $ cp -p .sccs2hg/2005-06-05_00\:00\:00\,nicstat.c nicstat.c $ ls -ogE nicstat.c -rw-r--r-- 1 14722 2012-08-24 11:22:48.819451726 -0700 nicstat.c $ hg add nicstat.c $ hg commit -m "added nicstat.c" $ cp -p .sccs2hg/2005-07-02_00\:00\:00\,nicstat.c nicstat.c $ ls -ogE nicstat.c -rw-r--r-- 1 14722 2012-08-24 11:22:48.819451726 -0700 nicstat.c $ hg diff $ hg commit nothing changed $ touch nicstat.c $ hg diff diff -r b49cf59d431d nicstat.c --- a/nicstat.c Fri Aug 24 11:21:27 2012 -0700 +++ b/nicstat.c Fri Aug 24 11:22:50 2012 -0700 @@ -2,7 +2,7 @@ * nicstat - print network traffic, Kb/s read and written. Solaris 8+. * "netstat -i" only gives a packet count, this program gives Kbytes. * - * 05-Jun-2005, ver 0.81 (check for new versions, http://www.brendangregg.com) + * 02-Jul-2005, ver 0.90 (check for new versions, http://www.brendangregg.com) * [...] Now, before you agree or disagree with me on whether this is a bug, I will also say that I believe it is a feature. Yes, I feel it is an acceptable shortcut because in "real" situations an edit to a file will change the modification time by at least one second (the resolution that hg diff or hg commit is looking for). The benefit of the shortcut is greatly improved performance of operations like "hg diff" and "hg status", particularly where your repository contains a lot of files. Why did I have no change in modification time? Well, my source file was generated by a script that I have written to convert SCCS change history to Mercurial commits. If my script can generate two revisions of a file within a second, and the files are the same size, then I run afoul of this shortcut. Solution - I will just change my script to apply the modification time from the SCCS history to the file prior to commit. A "touch -t " will do that easily.

  Read the article

• Problem with installing Nvidia display drivers on Ubuntu 13.10

  - by Pascal

  Hello everyone and thank you for taking a look at this topic! I'm currently trying out Ubuntu 13.10 but I keep hitting a wall when it comes to installing a driver. I've tried: sudo apt-get install nvidia-current This resulted in a un-bootable system. The screen just stayed black and the cursor displayed as an 'X'. After that I did had to re-install Ubuntu. The computer I'm using is an Acer-Aspire-V3 with a build in Nvidia geforce GT 630M and also with a Intel HD graphics chip-set (not sure if chip-set is the right word here). "lspci | grep VGA" output: pascal@pascal-Aspire-V3-571G:~$ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108M [GeForce GT 630M] (rev a1) I've searched a bit here and there and found out that it would be wise to mention that this laptop is using (or so I think) Nvidia Optimus, not sure if it will add anything to the subject but at least I'll mention it just to be sure. Now to the questions: Q1 How is this caused and how can I fix it? Q2 What additional information could I provide to help you help me?

  Read the article

• Low Graphics and laggy screen after update to 13.10 from 13.04

  - by Wh0RU

  After updating from 13.04 to 13.10 many of 3D unity stuff has stopped working, I am suing Samsung Series 3 (NP350V5X) Laptop which has Switchable Intel and AMD Radeon HD 7670M GFX. xserver-xorg-video-ati does works but NO 3D support and graphics are very low. [I am currently using this] fglrx & fglrx-updates shows blank screen after Login. Intel Graphic Install doesn't work either (dependency error) Output of $ sudo lshw -c video *-display description: VGA compatible controller product: Thames [Radeon HD 7500M/7600M Series] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:45 memory:e0000000-efffffff memory:c0120000-c013ffff ioport:3000(size=256) memory:c0100000-c011ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:bfc00000-bfffffff memory:d0000000-dfffffff ioport:4000(size=64) Similarly $ /usr/lib/nux/unity_support_test -p OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 256 bits) OpenGL version string: 2.1 Mesa 9.2.1 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Shows no 3D support. Can anyone please guide how to make things working again.

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• My wireless has suddenly became disabled by hardware switch, BIOS, rfkill, fn+f8 do nothing

  - by cwwk

  I have a toshiba l655d-s5145. There is no physical toggle for the wireless, although the f8 key is supposed to do the trick. It doesn't. The wireless has been working since October, and suddenly, nothing. RFKILL reports that the wireless is hard blocked, but unblock wifi, unblock 0, unblock all do nothing. I inserted a usb dongle, and that is also disabled by hardware switch, although rfkill reports that it is neither hard nor soft blocked. My onboard wireless is 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) according to lspci. Lsmod reports that these drivers are loaded. rtl8192c_common 75767 1 rtl8192ce rtlwifi 110972 1 rtl8192ce I resorted to reformatting the drive and reinstalling, but that also did not work. In BIOS I restored system defaults as there is no specific entry for wifi. Before reinstalling a pure xubuntu I went into Unity and saw that the airplane mode was on and despite being toggled off, it returned to the on position. I'm not sure where to find airplane mode in Xubuntu. What else can I do? I need my wireless.

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Broadcom Wireless Issues in Lubuntu 14.04

  - by ratxinxaxcage67

  I recently installed Lubuntu 14.04 on my parents' old laptop, and I've been having a super difficult time getting the Broadcom card up and running. I've been following this thread: Installing Broadcom Wireless Drivers ...but I'm still stuck. lspci -vnn | grep Network showed: 06:05.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 02) iwconfig showed: lo no wireless extensions. eth0 no wireless extensions. I've installed b43-firmware-installer and b43-fwcutter and also the linux-firmware-nonfree package. At boot, I keep getting a b43-phy0 error, so I tried sudo rmmod b43, and I got: rmmod: ERROR: Module b43 is not currently loaded I also tried: dmesg | grep b43 [ 17.318405] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4) [ 17.384870] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw [ 18.046777] b43legacy ssb0:0: Direct firmware load failed with error -2 [ 18.046785] b43legacy ssb0:0: Falling back to user helper [ 18.047858] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed. [ 18.047965] b43legacy-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3). I went to url it told me to, but it didn't tell me to do anything I haven't already tried. Any help and/or suggestions would be greatly appreciated!

  Read the article

• Ubuntu 13.10, kernel 3.11 blank screen issue with hybrid graphics

  - by Lagerbaer

  On my HP Envy, which has both an Intel on-chip graphics card and an Nvidia Geforce: *-display UNCLAIMED description: 3D controller product: GK208M [GeForce GT 740M] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:d2000000-d2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:5000(size=128) memory:b2000000-b207ffff *-display description: VGA compatible controller product: 4th Gen Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d3000000-d33fffff memory:c0000000-cfffffff ioport:6000(size=64) I have trouble with all newer kernels. I basically had to install 12.04 LTS and use their 3.5 kernel family to get the system to boot. The 3.8 from 12.10 or the newest 3.11 from Ubuntu 13.10 leave me with a black screen upon boot. On one occasion I did hear the "log in" sound, but the screen did not display anything. I have purged all nvidia drivers so I guess it should just use the intel drivers, but apparently this is all messed up with newer kernel versions. This is different from the other "nvidia boots into blank screen" bug in that I don't rely solely on an nvidia card. Surely the intel on-chip card should be supported and leave me with something different from a blank screen? Again, it only works with kernel versions 3.5.0-41-generic, not with the 3.11.0-12 one that ships with Ubuntu 13.10. When I go into the grub menu and change the boot options from 'quiet splash' to 'nomodeset' I am able to boot the system, but then I don't get any graphics and trying 'sudo service lightdm start' doesn't succeed (I get 100% CPU for apport, but this doesn't do anything either, so I kill it). Help, I'm all out of ideas. EDIT: Let me add that I'm using the EFI boot system and have a dual-boot installation with Windows 8.

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• Nvidia GeForce Gt-520M-cn on intel dh61ww Ubuntu 12.04

  - by j goseeped

  hi people i hope you can help a little bit , i appreciate your time look: i have a this desktop i7 2600, 8gb ram ddr3, board intel dh61ww, Geforce Nvidia GT520-cn 2Gb ddr3, i just install ubuntu 64bits 12.04 kernel 3.2.0-23-generic , i want to setup two monitors samsung led 22" and get start mi video card 1) i download and installed nvidia driver 295.59 and also try with 302.17 to apt-update and upgrade, apt-get install build-essential linux-headers-$(uname -r), apt-get remove --purge nvidia*, apt-get remove --purge xserver-xorg-video-nouveau, vim /etc/modprobe.d/blacklist.conf blacklist vga16fb blacklist nouveau blacklist rivafb blacklist nvidiafb blacklist rivatv sh NVIDIA.run, sudo service lightdm start, reboot, nvidia-xorgconf 2)after reboot i get 800x600 and nvidia-settings say this. You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run nvidia-xconfig as root), and restart the X server. 3) i change a little bit xorg.conf to set up a resolution to work property 4) i dont have any image in the monito and i dont have any option on Nvidia X server settings lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 520] (rev a1) egrep -i 'glx|nvidia' /var/log/Xorg.0.log [ 12.005] (II) LoadModule: "glx" [ 12.005] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 12.575] (II) Module glx: vendor="NVIDIA Corporation" [ 12.585] (II) NVIDIA GLX Module 302.17 Tue Jun 12 16:22:45 PDT 2012 [ 12.585] (II) Loading extension GLX [ 13.037] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event10) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event9) glxinfo | grep direct Xlib: extension "GLX" missing on display ":0.0". Error: couldn't find RGB GLX visual or fbconfig sorry my english is no very well. and thanks guys

  Read the article

• Why won't my graphics work in Ubuntu 12.04 LTS?

  - by user170974

  I'm very new to Ubuntu and to Linux in general, and took the leap and formatted my PC to Ubuntu 12.04 LTS very recently :) I seem to be having some trouble getting my graphics card to run properly, I looked over what information I could find but I still cannot get it up and running and figured this was a good place to ask for help. The information I can find on my graphics is as follows: (Terminal command) lspci outputs: 01:05.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RS880M [Mobility Radeon HD 4225/4250] 02:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Madison [Mobility Radeon HD 5650/5750 / 6530M/6550M] I tried using a mixture of the following links: How do I fix my installation of ATI Catalyst Video Driver in 12.04 LTS? What is the correct way to install ATI Catalyst Video Drivers (fglrx)? Ubuntu Precise Installation Guide But it does not seem to work, since running fglrxinfo in terminal gives: display: :0.0 screen: 0 OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 0x301) OpenGL version string: 1.4 (2.1 Mesa 9.0.3) What am I doing wrong here? All help appreciated ;) Edit: I have tried the legacy driver from www2.ati.com/drivers/linux/amd-driver-installer-catalyst-13-4-linux-x86.x86_64.zip I also tried the guide at https://launchpad.net/~makson96/+archive/fglrx which caused the system to crash (blackscreen, no boot) Neither seemed to work. I did however reinstall ubuntu 12.04 LTS, and re-tried both with no success. Reintalling ubuntu did however fix the broken dependencies problems, etc.

  Read the article

• Opengl + SDL linking error

  - by me2loveit2

  I am trying to load an image as a texture with opengl using c++ in visual studio 2010. I researched a couple hours online and found the SDL library, then I implemented a simple example and got some linking error I can not seem to figure out. The error log is here: 1Build started 10/20/2012 12:09:17 AM. 1InitializeBuildStatus: 1 Touching "Debug\texture mapping test.unsuccessfulbuild". 1ClCompile: 1 All outputs are up-to-date. 1 texture mapping test.cpp 1ManifestResourceCompile: 1 All outputs are up-to-date. 1texture mapping test.obj : error LNK2019: unresolved external symbol _IMG_Load referenced in function "void __cdecl display(void)" (?display@@YAXXZ) 1MSVCRTD.lib(crtexe.obj) : error LNK2019: unresolved external symbol main referenced in function __tmainCRTStartup 1C:\Users\Me\Documents\Visual Studio 2010\Projects\Programming projects\texture mapping test\Debug\texture mapping test.exe : fatal error LNK1120: 2 unresolved externals 1 1Build FAILED. 1 1Time Elapsed 00:00:02.45 ========== Build: 0 succeeded, 1 failed, 0 up-to-date, 0 skipped ========== Can someone please help me!! I am at a desperate point right now. I downloaded the SDL, and copied all the .h file into: C:\Program Files (x86)\Microsoft SDKs\Windows\v7.0A\Include I added the .lib (x86) files into://as a not i tried the (x64) file too but got the exact same error C:\Program Files (x86)\Microsoft SDKs\Windows\v7.0A\Lib and the .dll(x86) into: C:\Windows\System32 For implementing textures, I used the simple sample code from: http://www.sdltutorials.com/sdl-tip-sdl-surface-to-opengl-texture Please let me know if you can see me doing something wrong, or know how I can fix this!! Thanks Phil

  Read the article

• aplay -l says no soundcards found; alsaconf says no supported cords; yet /proc/asound contains cards

  - by nimasmi

  I am trying to get HDMI output using a Gainward Nvidia 210 512 MB on Ubuntu 10.04 Lucid Lynx. I have upgraded alsa-driver, alsa-lib and alsa-utils to 1.0.24 by building from source, thanks to this blog post. Some relevant output... user@box:~$ lspci | grep Audio 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 01:09.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05) 01:09.2 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05) 01:09.4 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) user@box:~$ cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.24. Compiled on Sep 15 2012 for kernel 2.6.32-42-generic (SMP). user@box:~$ ls /proc/asound` card0 cards hwdep NVidia oss seq version card1 devices modules NVidia_1 pcm timers user@box:~$ aplay -l aplay: device_list:240: no soundcards found... user@box:~$ sudo /sbin/alsa-utils start * Setting up ALSA... * warning: 'alsactl restore' failed with error message 'alsactl: set_control:1403: Cannot write control '2:0:0:IEC958 Playback Default:0' : Operation not permitted'... amixer: Invalid command! ...done. Any help appreciated. PS my video card is connected only through the PCI-E slot. I assume there is no extra audio connection required.

  Read the article

• How can I fix my xvinfo?

  - by YumYumYum

  How can i fix my X server/driver? $ xvinfo X-Video Extension version 2.2 screen #0 no adaptors present Additional info: $ uname -a Linux desktop 2.6.32-33-generic #70-Ubuntu SMP Thu Jul 7 21:13:52 UTC 2011 x86_64 GNU/Linux $ lspci 00:00.0 Host bridge: Intel Corporation Device 0100 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Sandy Bridge Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 1503 (rev 05) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4a (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 PCI bridge: Integrated Technology Express, Inc. Device 8892 (rev 10) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) Follow up: It seems in 64-bit its a mess doing existing approach. Therefore, after upgrading to 12.04 64-bit this problems in same hardware is resolved (of-course, i have now other drivers problem)

  Read the article

• AR242x / AR542x wireless card not working

  - by Pipan87

  My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

  Read the article

• How to make backlight work on Acer 5732z?

  - by Dude Random21

  I want to run 12.04 on my Acer Aspire 5732z. I know from research that these computers have issues with the backlight on Ubuntu. So I tried a couple of solutions: The sudo lightdm restart method. I get no change at all. The sudo setpci -s 00:02.0 F4.B=30 method. This so far has been the most effective. I first tried it in the F1 console, right away I get the screen back, problem is going back to the desktop it goes back to being black. So I tried it from a terminal window and it works as well but as soon as I unplug my external monitor the screen turns black again and doesn't come back. If I plug the monitor back in the screen stays black and the only thing I see is the mouse pointer. From here I go back into console (which I am able to see) and reboot from there. The sudo sed -i 's/GRUB_CMDLINE_LINUX=""/GRUB_CMDLINE_LINUX="acpi_osi=Linux"/g /etc/default/grub method. This one I got no instant change and after reboot still no change. I'm open to pretty much any suggestions you may have.

  Read the article

• How to disable discrete GPU using NVIDIA drivers?

  - by penzoiders

  I have a DELL studio XPS 13 (aka 1340) as of 12.04 most things run smoothly out of the box, but I have some power draining and warmness issues (if not to be called terrible heat issues) The system came with a NVIDIA GeForce 9500M (which has Hybrid SLI) and it shows up in "lspci" as these 2 cards 02:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce 9200M GS] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation C79 [GeForce 9400M G] (rev b1) I had to install nvidia-current over noveau driver 'cause noveau does freeze the system after suspension. By installing nvidia-current and running nvidia-xconfig the resume process after suspension is fixed. By the way both with nvidia-current and noveau the system drains a lot of battery and heats up a lot. I suppose this is because the discrete GPU is always on. I don't really need 3D graphics on this system, if not the minimal to run unity and compiz for window management. So my question is: How do I disable, using nvidia-current, the discrete GPU 9200M and use only the integrated one 9400M? notes: In BIOS I have no option to disable discrete GPU This I think is not applicable because of the suspension-freeze issue (with noveau): https://help.ubuntu.com/community/HybridGraphics I've found this but I don't know which --sli option I should choose to fit my needs: http://manpages.ubuntu.com/manpages/hardy/man1/nvidia-xconfig.1.html My system has not optimus or cuda, but anyone can tell me if bumblebee can work for me?

  Read the article

• Wifi doesn't connect if I'm upstairs

  - by user11233

  Hello there, I'm finding that Wifi connects when I'm in the living room, where the internet router etc is. But if I try to connect upstairs it is a no go. Booting in Windows 7 (dual boot :D ) I find that Wifi connects. I find this very confusing and have it since the install. Please help! Kind regards. #sudo lshw -c network *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 00:21:5d:1a:63:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=2.6.35-26-generic firmware=8.24.2.12 ip=10.0.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11abg resources: irq:49 memory:de200000-de201fff Hope it helps! Hello guys, just tried to connect internet upstairs and to my surprise it does connect. Don't know exactly why. Only thing I've done recently is input the codes said bij Oli. Two things I've done on my own 1: installed Jupiter and 2: installed laptop-mode-tools. I really don't know if this can effect my internet but it's the only thing I can think of. Thanks for all the help, really appreciate it :) PS If someone thinks it might be helpful for others I would like to help find a 'real' solution to this problem. Just post down what I need to post here and I will try my best to help.

  Read the article

• 2 folders in Sys/Class/Backlight?

  - by zebrapie

  ISSUE: Backlight brightness does not change. More Detail: Brightness will not change, using both 'System Settings-Screen', or FN keys (Brightness bar shows and moves, but screen brightness does not change). Notcied a post in this thread (http://ubuntuforums.org/showthread.php?t=1866283) about having multiple folders in Sys-Class-Backlight... I HAVE TWO FOLDERS TOO! 'intel_backlight' and 'acpi_video0' Using the function keys, alters the value in the acpi_video0's 'Brightness' file - But doesn't actually alter the brightness of the screen. If I add 'backlight=vendor' in Grub, my function keys then edit the value in the 'Intel_Backlight brightness file. - But again doesnt actually change the brightness of the screen. Computer: Fujitsu Siemans Pi2515, Intel Integrated Graphics, No hdd partition. Already Tried: -Editing grub to contain: acpi_osi=Linux acpi_backlight=vendor -http://ubuntuguide.net/change-screen-brightness-with-fn-key-in-ubuntu-11-0410-10 -sudo apt-get install acpi -$ sudo setpci -s 00:02.0 F4.B=20 -Brightness does not adjust in fallback mode either. -Reinstalling OS, Using Linux Mint (Same problem). -Upgrading and downgrading BIOS. Many thanks for reading, I understand this problem may need a bit of a Linux pro to sort. If anyones up for the challenge i'll spend any amount of time being walked through this, posting results. Don't want to give up here!

  Read the article

• Using onboard and pci-e graphics card at the same time

  - by Endle

  Hello wonderful people. I know there are several other posts with similar questions. I also know how to use Google. I also have read up on posts discussing bumblebee, crossfire, ati catylist and many other interesting topics. I would just like someone to give me advice on how to use the onboard and pci-e graphics at the same time. I know the computer is capable of doing this. It works in Windows. I can use the VGA and DVI onboard port and the HDMI port of the add on card all at the same time. Works great in Windows 7, In Ubuntu, it seems only one or the other will work. I can use any combination of two displays on either adapter: VGA and HDMI..HDMI and DVI..so forth and so on. I have started experimenting with xorg.conf files, but have not been able to get any of them to work. Here is my last attempt at writing an xorg.conf file: Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" LeftOf "Screen0" Screen 2 "Screen2" LeftOf "Screen1" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Device" Identifier "Onboard Video" Driver "radeon" BusID "PCI:01:05.0" EndSection Section "Device" Identifier "Graphics Card" Driver "radeon" BusID "PCI:02:00.0" EndSection Section "Monitor" Identifier "CRT2" Option "VendorName" "ViewSonic" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "DVI1" VendorName "ACR" ModelName "P224W" Option "DPMS" EndSection Section "Monitor" Identifier "DVI2" Option "VendorName" "Acer" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Screen" Identifier "Screen0" Device "Onboard Video" Monitor "CRT2" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1280x1024" EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Graphics Card" Monitor "DVI1" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1920x1080" EndSubSection

  Read the article

• M-Audio Delta 1010LT on 12.04

  - by user74039

  I have 12.04 64bit installed, my soundcard is a Delta 1010LT, it seems to be partially detected, I've been following steps here: https://help.ubuntu.com/community/SoundTroubleshooting/ lspci -v | grep -A7 -i "audio" shows this: 04:07.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. M-Audio Delta 1010LT Flags: bus master, medium devsel, latency 64, IRQ 22 I/O ports at ec00 [size=32] I/O ports at e880 [size=16] I/O ports at e800 [size=16] I/O ports at e480 [size=64] Capabilities: <access denied> Kernel driver in use: snd_ice1712 aplay shows this: **** List of PLAYBACK Hardware Devices **** card 0: M1010LT [M Audio Delta 1010LT], device 0: ICE1712 multi [ICE1712 multi] Subdevices: 1/1 Subdevice #0: subdevice #0 In the sound settings on the desktop all I see is the ICE1712 S/PDIF, which I don't use, I want to use the individual outputs on the card, I'm not so bothered about inputs, I just want the playback for now. If I open alsamixer in the console, I see all of the output and input channels, i've raised the volume on them but I don't get anything in the sound settings on the desktop and when I play any sound, I hear nothing. Can someone help?

  Read the article

< Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >