Search Results

Search found 35784 results on 1432 pages for 'number format'.

Page 652/1432 | < Previous Page | 648 649 650 651 652 653 654 655 656 657 658 659  | Next Page >

• Raid HDD Boot up

  - by user234695

  My server is Power Edge 1950 running server 2008 32Bit, using 3 Physical SAS HDD as a Virtual 2 Disk configured for RAID5, with partition of C drive as OS and D drive as Data. Planning to format and install Server 2008 R2 64Bit so I insert a New Physical disk and configured as RAID5 and clone the C drive and D drive to the new hard disk. Now I need to test that the new hard disk is able to boot windows and work as expected. How do I test, I am not able to boot the windows by choosing the new harddisk, the bios show only the existing HDD, not the new one. Also, if I remove the old three hard disk, and leave the new harddisk and then am I able to boot the device, if I do this does my existing RAID5 configuration and data on the hard disk still remain.

  Read the article

• How do I set a default host for nginx?

  - by ulf

  I'm trying to figure out how to set a default host for my nginx installation. I found this article in the nginx Wiki: http://wiki.nginx.org/NginxVirtualHostExample#A_Default_Catchall_Virtual_Host Unfortunately, this doesn’t work. After restarting I get this: Restarting nginx: nginx: [emerg] unknown directive "http" in /etc/nginx/sites-enabled/catchall:1 nginx: configuration file /etc/nginx/nginx.conf test failed After removing the http directive I get this: Restarting nginx: nginx: [emerg] unknown log format "main" in /etc/nginx/sites-enabled/catchall:7 nginx: configuration file /etc/nginx/nginx.conf test failed I’m on Ubuntu 10.04.3 where I’m using the official nginx PPA. Version 1.0.9 of nginx is running.

  Read the article

• F5 BigIP upgrade from 9.x to 10.x

  - by mbuk2k

  Having a few difficulties upgrading a Big IP 3400 from 9.4.8 to any version 10.x image. The following are the versions I've tried: 10.1.0.3341.0 10.2.2.763.3 10.2.3.112.0 10.2.4.577.0 To upgrade I'm running the following command: image2disk --format=volumes BIGIP-10.1.0.3341.0.iso Obviously replacing the version number with the relevant image I'm trying to upgrade to each time. The F5 reboots, and starts copying packages however after 30 seconds or so just stops copying. The cursor in the console is still flashing but no matter how long it's left, the package doesn't copy. It seems to be a different package with each version/image (but always the same package per version) at point of freezing, which I'm guessing is suggesting a space issue? I've checked free space on the device and it has over 2GB free at root which should surely be enough? If anyone has any advice or pointers, it would be kindly appreciated. Thank you

  Read the article

• mime-attachment incompatibility on forwarded messages from android to an iphone

  - by Peter Carrero

  A couple of guys got the evo android in the office. I got an iphone. When I receive a forwarded email from one of those phones, the forwarded piece comes as a mime-attachment that the iphone cannot open. I also tried this with a motorola droid and got the same result. I am not sure if the issue is the android sending the message on the wrong format or the iphone not being able to understand a mime type that it should... Has anyone experienced this, and, most importantly, found a fix/workaround? Thanks.

  Read the article

• Tool to fix video that's out of sync with audio?

  - by Javier Badia

  I'm looking for (preferably free) software for Windows 7 that will allow me to fix an AVI file that has audio out of sync with the video. I tried with Windows Live Movie Maker and VirtualDub and couldn't find out how to do it (if at all possible) on both of them. If any of those can help me, instructions for that would also be nice. Background: I have a RCA-to-USB capture card, which I'm using to transfer VHS casettes and stuff from a video camera to digital format. The problem is that the audio comes out heavily distorted. So instead I connected the audio out from the VCR directly to the computer's line in. This works, but the audio is out of sync, about half a second behind the video. I could spend time trying to fix this issuee, but I think it'll be easier to simply fix the video.

  Read the article

• Free desktop recording / screencasting on windows

  - by Mercer Traieste

  I'm a newbie in desktop recording and screencasting. I didn't find a suitable free application to do all the things I want it to do, but I did enjoy using jing. I would expect such an application to have these features: choose the whole desktop, a region, a window to record zoom in an area, and camera move save the recorded movie to a compressed format have basic editing tools have the mouse highlighting feature (either a sonar blip or something similar) highlight window/field on the screen, any trick will do display pressed keys/key combinations (like iphone does) So the question is: Which free desktop recording/screencasting software would you recommend on windows? It doesn't have to have all those features, just tell me your favorable experiences. Please suggest tools that would do mouse/keys/areas highlight tricks. I'm open to commercial software too, but I would prefer a free one. Thank you!

  Read the article

• What is the easiest way to get a yyyy-mm-dd hh:mm:ss timestamp hotkey on the Mac?

  - by Edward Tanguay

  On Windows I use the PSPad editor which has a nice ALT-D timestamp which you can edit the format of, e.g. yyyy-mm-dd hh:mm:ss. When working outside an editor, e.g. Google Docs, I have Autohotkey which I have programmed CTRL-D to insert a yyyy-mm-dd hh:mm:ss timestamp. I am now working on a Mac mostly using TextWrangler as my editor but I can't find a timestamp hotkey in its features. What is the easiest way to get a yyyy-mm-dd hh:mm:ss hotkey on Mac, either in a (free) text editor or a (free) autohotkey equivalent?

  Read the article

• How to use HTML markup tags inside Bash script

  - by CONtext

  I have crontab and a simple bash script that sends me emails every often containing PHP, NGINX, MYSQL errors from their log files. This is a simplified example. #/home/user/status.sh [email protected] PHP_ERROR=`tail -5 /var/log/php-fpm/error.log` NGINX_ERROR=`tail -5 /var/log/nginx/error.log` MYSQL_ERROR=`tail /var/log/mysqld.log` DISK_SPACE=`df -h` echo " Today's, server report:: ================================== DISK_SPACE: $DISK_SPACE --------------------------------- MEMORY_USAGE: $MEMORY_USAGE ----------------------------------- NGINX ERROR: $NGINX_ERROR ----------------------------------- PHP ERRORS: $PHP_ERROR ------------------------------------ MYSQL_ERRORS: $MYSQL_ERROR ------------------------------------- " | mail -s "Server reports" $EMAIL I know this is a very basic usage, but as you can see, I am trying to separate the errors, but not of the html tags including \n are working. So, my question is, is it possible to use HTML tags to format the text, if not .. then what are the alternatives.

  Read the article

• HDD is not recognized/initialized via USB, only via SATA - is a reformat through USB a bad idea?

  - by Wuschelbeutel Kartoffelhuhn

  I have a 4TB Hitachi HDD that I purchased in Europe (I use it as a backup disk); I use Windows 7. When I connect it to a SATA port, it is recognized in Windows Explorer and gives no problems, even after transferring 3TB at a time or after being on for days. When I connect it via a SATA-to-USB2.0 adapter, it is also recognized, but when I transfer a large amount of data, it will intermittently stop being recognized by Windows Explorer and cancel the transfer. When I connect it via an external enclosure (which is technically a SATA-to-USB3.0 adapter), it does not display at all in Windows Explorer, but Disk Management will show the drive, albeit uninitialized (prompts for format). I only got the external enclosure because I want to backup my files more conveniently (instead of having to open the computer case each time). Do you advise against reformat/initialization via the external enclosure? Can it screw up things in an irrevocable way (Master Boot Record etc.)?

  Read the article

• Where to set Visual studio 2013 property macros

  - by marcp

  I'm a new VS user. I've received some sample C++ projects working with a 3rd party API. They were saved in VS2012 format, but I have VS 2013. After conversion I find that there is an API specific macro defined in the project properties in the "Linker|General|Additional Library Directories" category. If I click on 'edit' I can replace the macro with an actual path, but how do I establish what the macro points to? In other words, how does one create a macro usable in multiple projects?

  Read the article

• Reinstall after a Root Compromise?

  - by Zoredache

  After reading this question on a server compromise, I started to wonder why people continue to seem to believe that they can recover a compromised system using detection/cleanup tools, or by just fixing the hole that was used to compromise the system. Given all the various root kit technologies and other things a hacker can do most experts suggest you should reinstall the operating system. I am hoping to get a better idea why more people don't just take off and nuke the system from orbit. Here are a couple points, that I would like to see addressed. Are there conditions where a format/reinstall would not clean the system? Under what types conditions do you think a system can be cleaned, and when must you do a full reinstall? What reasoning do you have against doing a full reinstall? If you choose not to reinstall, then what method do you use to be reasonably confident you have cleaned and prevented any further damage from happening again.

  Read the article

• Recovered all previous data of partition in Windows

  - by Komal Sorathiya

  My whole drive data is lost because I installed ubuntu. After that, I formatted my Laptop and make new drives. in which, one partition is cant accessible because its a raw partition. I recovered some data from that partition using iCare Recovery Software. Then, I fully format that partition, and I put data in that place. I remove all files from that. My problem is that I want to recover my data which is deleted because of ubuntu.. I can recover the most recent data from iCare Recovery, but i cannot recover previous data.. Please, help me for that. I am trying this from many days. Thanks

  Read the article

• Archiving old, outdated hard drives

  - by Calvin

  I have a number of old hard drives. I've decided to throw them out. But before I do that, I'd like to keep the contents of hard drives, intact. I tried to use the ISO file format to archive but the major problem is that it loses file attributes and can't create directories with exceeding depth of 8 levels. I do have drives over a variety of file systems; FAT, NTFS, ext2, ext3 and HFS and I'd like to archive them without any loss of information.

  Read the article

• How to access an SD card from a virtual machine?

  - by Punit Soni

  I want to format an SD card from my Linux virtual machine. I have a built-in SD card reader in my laptop. I tried using VirtualBox and VMware Player and installed Ubuntu 10.04 guest. None of them are showing the SD card reader as a device. I can access the SD card from the Windows host. I am not interested in solutions using shared folders as I want to access the SD card as hardware (it should show up in /dev). I basically want to set up the SD card for BeagleBoard, but I don't want to install physical Ubuntu in my PC.

  Read the article

• Windows 2008 R2 server cannot access shares on other servers

  - by Rob

  I have a problem on my new 2008 R2 64-bit server. Essentially the server sometimes refuses to access shares on other server. in the format \\servernam\sharename sometime it works and then for a few hours it doesn't and then at randon it comes back online. This is a local AD network and have even put in a new gigabit switch between all server. All the old 2003 servers work fine so I know DNS and WINS is all ok. I get error 1006 in eventlog saying that my R2 server can't contact the domain controller when it clearly can. Just to add to the config, it is running on a Dell PowerEdge R410, Vmware Esxi 4.0 and R2 is configured as a terminal server. I can always view shares with FQDN This morning net view \\ did not work but net view \\ did. Very random and very frustrating. any ideas? thanks

  Read the article

• OpenVPN Client timing out

  - by Austin

  I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

  Read the article

• Nginx static files exclude one or some file extensions

  - by Evgeniy

  I'm serving up a static site via nginx. location ~* \.(avi|bin|bmp|dmg|doc|docx|dpkg|exe|flv|gif|htm|html|ico|ics|img|jpeg|jpg|m2a|m2v|mov|mp3|mp4|mpeg|mpg|msi|pdf|pkg|png|ppt|pptx|ps|rar|rss|rtf|swf|tif|tiff|txt|wmv|xhtml|xls|xml|zip)$ { root /var/www/html1; access_log off; expires 1d; } And my goal is to exclude requests like http://connect1.webinar.ru/converter/task/. Full view is like http://mydomain.tld/converter/task/setComplete/fid/34330/fn/7c2cfed32ec2eef6788e728fa46f7a80.ppt.swf. Despite the fact these URLs ends in such a format they are not static, but fake script requests, so I have a problems with them. What is the best way to do this? How can I add an exclusion for this URL or maybe I can to exclude the specific file exptension (.ppt.swf, pptx.swf) from the list of this Nginx location? Thanks.

  Read the article

• How to Modify a Cronjob Email Subject

  - by justinl

  I am running a half dozen different cron jobs from my hosting at Hostmonster.com. When a cronjob has been executed I receive an email with the output of the script. The email comes in the format of: From: Cron Daemon Subject: Cron /ramdisk/bin/php5 -c /home5/username/scheduled/optimize_mysql.bash The problem with this is that the subject of the email makes it very hard to read which cronjob the email is pertaining to. Is there a way to modify the subject of a cronjob email so that it's easier to read? For example: From: Cron Daemon Subject: Optimize MySQL Database

  Read the article

• What is the Everyone built-in windows security group called in Portuguese?

  - by JohnLBevan

  I'm attempting to setup share permissions on a Brazilian server and wish to give Everyone read only access. However, the server's language is Brazilian (Portuguese), and it looks like the security groups' names have been translated. Does anyone know what this group is called in Portuguese? Is there an easy way to access this group which is not language sensitive (e.g. some constant value, such as the SID (S-1-1-0) which can always be used, regardless of locale settings)? http://support.microsoft.com/kb/243330. NB: I tried using this SID, but on its own it did not work - though perhaps I need to format it in some way?

  Read the article

• WOL not working

  - by Maciej Swic

  I have a Marvell Yukon integrated NIC and i have installed the WOL package on my freeBSD-based NAS. I'm trying to wake my PC using the command "wol M:A:C:A:D:D:R". Command line spits back that it is "waking" however nothing happens. I found no reference to WOL whatsoever in BIOS and i enabled Magic Packet WOL in windows on that interface. Also double-checked MAC addr and that i entered it in the correct format in "wol". I'm on Windows 7. What next? =/

  Read the article

• How to convert series of MP3 to a M4B in a batch

  - by Artem Tikhomirov

  Hello. I have a batch of MP3 based books. Some of them divide into files according to book's own structure: chapters and so on. Some of them was just divided into equally lengthened parts. So. I've bought an iPhone, and I want to convert them all to M4B format. How could I convert them in a batch? I mean how cold I set up a process once, for each book, and then, after couple of weeks, receive totally converted library. The only able program for such conversion I've found was Audiobook Builder for a Mac. But it is pretty slow and do not support batching in principle. Solutions for any platform, please.

  Read the article

• partitioning problems

  - by Remus Rigo

  I had on my laptop a dual system (Ubuntu 11.04 and Windows 7) and someway the partitions messed-up. Windows stopped from booting, I just got a blinking cursor, but Ubuntu worked fine. I tried to fix the windows boot (fixmbr, fixboot, bootsect /nt60 C:/....) but now grub was overwritten and I have no OS. Finally I formatted the hdd (low format), installed Windows, partition hdd with paragon partition manager and now I want to install Ubuntu, but Ubuntu sees an empty hdd, weird, can anyone tell me what can I do? EDIT: I have created: partition 1: 100MB ntfs - windows reserved (drive B) partition 2: 50GB ntfs win 7 (drive C) partition 3: 50GB ext3 linux partition 4: 'the rest' ntfs for data (drive E) (the swap i will create after)

  Read the article

• Is it possible/How to boot an XP VHD in Windows 7

  - by jvanderh

  In windows 7 it is pretty simple to boot directly to a VHD, given that it also contains (or you are going to install) Windows 7 (or Vista/Server 2008). This installation is made possible I believe by the fact that from Vista on, Microsoft is using WIM (Windows Imaging Format) for OS installation. Is there a way to install XP to a VHD on Windows 7? Or is there a way to create a WIM image of the XP installer? Some have claimed to be able to do it in different blog posts, but there are no explanations of how to achieve it.

  Read the article

• Proffesional video editor that can handle FLV?

  - by acidzombie24

  I tried Adobe Premiere Pro CS3 and was not able to open my file (unsupported format). Media player can open it thanks to ffdshow (tryouts IIRC). Premiere doesnt seem to want to use ffdshow. I tried renaming it to AVI and hoped Premiere would open it via ffdshow but it didnt and i checked and disabled the dont use ffdshow option in ffdshow video decoder option. What is a good proffesional video editor that can handle FLV? All ffmpeg based editors died on it and virtualdub got close but had a bad framerate. Probably bc it didnt know it was a streaming vid and the start is 26mins of 31min video. More info here but what can i use to open and properly convert flv video http://superuser.com/questions/50779/windows-media-based-video-audio-converter

  Read the article

• Three ways to upload/post/convert iMovie to YouTube [closed]

  - by alexyu2010

  For Mac users, iMovie is probably a convenient tool for making, editing their own home movies so as to upload to YouTube for sharing with more people. However, uploading iMovie files to YouTube can't be always a smooth run, I did notice many people complaining about it. This article is delivered for guiding those who are haunted by the nightmare by providing three common ways to upload iMovie files to YouTube. YouTube and iMovie YouTube is the most popular video sharing website for users to upload, share and view videos. It empowers anyone with an Internet connection the ability to upload video clips and share them with friends, family and the world. Users are invited to leave comments, pick favourites, send messages to each other and watch videos sorted into subjects and channels. YouTube accepts videos uploaded in most container formats, including WMV (Windows Media Video), 3GP (Cell Phones), AVI (Windows), MOV (Mac), MP4 (iPod/PSP), FLV (Adobe Flash), MKV (H.264). These include video codecs such as MP4, MPEG and WMV. iMovie is a common video editing software application comes with every Mac for users to edit their own home movies. It imports video footage to the Mac using either the Firewire interface on most MiniDV format digital video cameras, the USB port, or by importing the files from a hard drive where users can edit the video clips, add titles, and add music. Since 1999, eight versions of iMovie have been released by Apple, each with its own functions and characteristic, and each of them deal with videos in a way more or less different. But the most common formats handled with iMovie if specialty discarded as far as to my research are MOV, DV, HDV, MPEG-4. Three ways for successful upload iMovie files to YouTube Solution one and solution two suitable for those who are 100 certainty with their iMovie files which are fully compatible with YouTube. For smooth uploading, you are required to get a YouTube account first. Solution 1: Directly upload iMovie to YouTube Step 1: Launch iMovie, select the project you want to upload in YouTube. Step 2: Go to the file menu, click Share, select Export Movie Step 3: Specify the output file name and directory and then type the video type and video size. Solution 2: Post iMovie to YouTube straightly Step 1: Launch iMovie, choose the project you want to post in YouTube Step 2: From the Share menu, choose YouTube Step 3: In the pop-up YouTube windows, specify the name of your YouTube account, the password, choose the Category and fill in the description and tags of the project. Tick Make this movie more private on the bottom of the window, if possible, to limit those who can view the project. Click Next, and then click Publish. iMovie will automatically export and upload the movie to YouTube. Step 4: Click Tell a Friend to email friends and your family about your film. You are also allowed to copy the URL from Tell a Friend window and paste it into an email you created in your favourite email application if you like. Anyone you send to email to will be able to follow the URL directly to your movie. Note: Videos uploaded to YouTube are limited to ten minutes in length and a file size of 2GB. Solution 3: Upload to iMovie after conversion If neither of the above mentioned method works, there is still a third way to turn to. Sometimes, your iMovie files may not be recognized by YouTube due to the versions of iMovie (settings and functions may varies among versions), video itself (video format difference because of file extension, resolution, video size and length), compatibility (videos that are completely incompatible with YouTube). In this circumstance, the best and reliable method is to convert your iMovie files to YouTube accepted files, iMovie to YouTube converter will be inevitably the ideal choice. iMovie to YouTube converter is an elaborately designed tool for convert iMovie files to YouTube workable WMV, 3GP, AVI, MOV, MP4, FLV, MKV for smooth uploading with hard-to-believe conversion speed and second to none output quality. It can also convert between almost all popular popular file formats like AVI, WMV, MPG, MOV, VOB, DV, MP4, FLV, 3GP, RM, ASF, SWF, MP3, AAC, AC3, AIFF, AMR, WAV, WMA etc so as to put on various portable devices, import to video editing software or play on vast amount video players. iMovie to YouTube converter can also served as an excellent video editing tool to meet your specific program requirements. For example, you can cut your video files to a certain length, or split your video files to smaller ones and select the proper resolution suitable for demands of YouTube by Clip or Settings separately. Crop allows you to cut off unwanted black edges from your videos. Besides, you can also have a good command of the whole process or snapshot your favourite pictures from the preview window. More can be expected if you have a try.

  Read the article

< Previous Page | 648 649 650 651 652 653 654 655 656 657 658 659  | Next Page >