Search Results

Search found 23427 results on 938 pages for 'christopher done'.

Page 655/938 | < Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >

  • Internet slowed down because of SQUID Server setup

    - by Ranjith Kumar
    Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

    Read the article

  • Do registry issues with Win7 persist through a recovery from a system image?

    - by user59089
    So I need a bit of advice, please; here's my situation: I have 1) a system image on an a brand new external 1 TB SATA drive, that I managed to successfully capture before my 2) primary system drive went down. I realize this is a fairly simple matter of buying a new primary drive and performing the recovery to the fresh disk...however, the issue is that I believe Win7 was also having some significant issues of its own--basically, Update unable to install updates, and Backup continually ditching the auto backup schedule. I'd been trying to address those issues when my system was still working, but it's been so fruitless, I'm convinced a Win7 re-install would be best, and now I'm concerned that if I was in fact having what I believe are likely registry-related issues before, that these will persist through a recovery--would that likely be correct? I'm mainly worried about recovering my files, so if I did a full recovery from the image, should I be able to then access my individual files, and copy them manually to an external drive, so I can then do a full re-install of Win7? Sory if this seems obvious, but I've never done a recovery before and just trying to make sure there's no red flags with what I have in mind...

    Read the article

  • What permission(s) does an application pool identity required to manage other application pools?

    - by Mr Shoubs
    I have a web site (used to manage various parts of our software) that needs the permissions required to start/stop other application pools. I've created a user and set the app pool identity to custom, however the web app still can't start/stop the app pools. I get the following Error: System.UnauthorizedAccessException: Filename: redirection.config Error: Cannot read configuration file due to insufficient permissions at Microsoft.Web.Administration.Interop.AppHostWritableAdminManager.GetAdminSection(String bstrSectionName, String bstrSectionPath) at Microsoft.Web.Administration.Configuration.GetSectionInternal(ConfigurationSection section, String sectionPath, String locationPath) at Microsoft.Web.Administration.ServerManager.get_ApplicationPoolsSection() at Microsoft.Web.Administration.ServerManager.get_ApplicationPools() Discussion here suggests setting the application pool to local system or administrator, this does work, but I don't want to do this for security reasons (external support will need access this site). I did give the user higher permissions (as suggested here), starting by making it part of the local administrators group, but initially this didn't work, and giving the user read/write/mod permission on C:\Windows\System32\inetsrv\config also didn't work. I must have done something wrong as local administrator now works, however this still isn't what I want. So can anyone suggest the permissions I need to add to this user, and how can I apply them? An answer my problem (but different question) is here, but to clarify, I think I need to give an individual user "IIS Runtime Operation Permissions", does anyone know how to do this, if indeed this is the permissions I require?

    Read the article

  • Google-Bot fell in love with my 404-page

    - by 32bitfloat
    Every day my access-log looks kind of this: 66.249.78.140 - - [21/Oct/2013:14:37:00 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.78.140 - - [21/Oct/2013:14:37:01 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.78.140 - - [21/Oct/2013:14:37:01 +0200] "GET /vuqffxiyupdh.html HTTP/1.1" 404 1189 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" or this 66.249.78.140 - - [20/Oct/2013:09:25:29 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.75.62 - - [20/Oct/2013:09:25:30 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.78.140 - - [20/Oct/2013:09:25:30 +0200] "GET /zjtrtxnsh.html HTTP/1.1" 404 1186 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" The bot calls the robots.txt twice and after that tries to access a file (zjtrtxnsh.html, vuqffxiyupdh.html, ...) which cannot exist and must return a 404 error. The same procedure every day, just the unexisting html-filename changes. The content of my robots.txt: User-agent: * Disallow: /backend Sitemap: http://mysitesname.de/sitemap.xml The sitemap.xml is readable and valid, so there seems to be no reason why the bot should want to force a 404-error. How should I interpret this behaviour? Does it point to a mistake I've done or should I ignore it?

    Read the article

  • How to restrict postfix send limited email with policyd v2?

    - by Shalini Tripathi
    I have installed cluebringer-2.0.7 for postfix and enabled below lines in the main.cf file of postfix. But I could not see any policy working smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination check_policy_service inet:127.0.0.1:10031 smtpd_end_of_data_restrictions=check_policy_service inet:127.0.0.1:10031 To check further I enabled logging in policyd and its only shows below logs and there is no logs getting populated when I send new emails.. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Process Backgrounded [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Policyd v2 / Cluebringer - v2.0.7 [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Initializing system modules. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: System modules initialized. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load started... [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = AccessControl: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckHelo: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckSPF: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Greylisting: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Quotas: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Postfix): enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Bizanga): enabled [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load done. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: 2012/06/12-21:18:50 cbp (type Net::Server::PreFork) starting! pid(13949) [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Binding to TCP port 10031 on host * [2012/06/12-21:18:50 - 13949] [CORE] WARNING: Group Not Defined. Defaulting to EGID '0 10 6 4 3 2 1 0' [2012/06/12-21:18:50 - 13949] [CORE] WARNING: User Not Defined. Defaulting to EUID '0' Do I need to do anymore settings for postfix to listen on policyd???Please help

    Read the article

  • Subdomains and address bar

    - by Priednis
    I have a fairly noob question about how subdomains work. As I understand at first the DNS server specifies that a request for certain subdomain.domain.com has to go to the IP address of domain.com, and the webserver at domain.com further processes the request and displays the needed subdomain page. It is not entirely clear to me how (for example Apache) server does it. As I understand there can be entries in vhosts.conf file which specify folders that contain the subdomain data. Something like: <VirtualHost *> ServerName www.domain.com DocumentRoot /home/httpd/htdocs/ </VirtualHost> <VirtualHost *> ServerName subdomain.domain.com DocumentRoot /home/httpd/htdocs/subdomain/ </VirtualHost> and there also can be redirect entries in .htaccess files like rewritecond %{http_host} ^subdomain.domain.com [nc] rewriterule ^(.*)$ http://www.domain.com/subdomain/ [r=301,nc] however in this case the user gets directed to the directory which contains the subdomain data but the user gets "out" of the subdomain. I would like to know - how, when going to subdomain.domain.com the subdomain.domain.com, beginning of address remains visible in the address bar of the explorer? Can it be done by an alternate entry in .htaccess file? If a VirtualHost entry is specified in the vhosts.conf file, does it mean, that a new user account has to be specified for access to this directory?

    Read the article

  • My desktop has started overheating -- how hot is hot?

    - by Jerry
    I have a two year old desktop, some random quad core HP desktop. It used to run very quietly, but in the past month, the fans start up anytime anything "serious" is being done -- compiles, playing video, etc. Right now, speedfan and speccy report the cores are between 50C and 70C. Speedfan reports this as hot. (Nice flame icon.) Well, the system does sit on my carpet, so two weeks ago, I took off the lid, and cough *cough* it was pretty filled with dust. I got out an air can, turned on a vacuum and carefully got out all the dust that I saw on the CPU fan the case fans any fan I saw (graphics board) and blew out all the dust I could from all the circuit boards. And then I closed the case back up. It has definitely run cooler since then, but it still runs hot, and I hear high speed fan noise I never heard before. How hot is too hot? At what temps do consumer grade CPUs die? What should I be looking to do? Replace CPU fan? (It seems to work) Replace power supply fan? Assuming the dust problem is gone, where should I be looking to determine why the machine is heating up? Epilogue: After following the various pieces of advice given here, the system did run cooler, but it was still noticeably running louder (hotter) than just a few months prior. I ended up purchasing a new cpu heatsink and fan and during installation found the cooling grease from the original heatsink was just a dried, cracked layer, probably more of an insulator than heat transfer agent. With the new fan AND the new heatsink compound, the system ran much much cooler and the fan rarely turns on.

    Read the article

  • Trouble with IIS SMTP relaying to Gmail

    - by saille
    I appreciate that similar questions have been asked about how to setup SMTP relaying with IIS's virtual SMTP server. However I'm still completely stumped on this problem. Here's the setup: IIS 6.0 SMTP server running on Win2k3 box with a NAT'ed IP. Company uses Gmail for all email services. An app on the box needs to send email, so normally we'd just set the app up to talk to smtp.gmail.com directly, but this app doesn't support TLS. Easy, we just setup a local SMTP relay right? So I thought. What we have done so far: Setup IIS SMTP server to relay to smtp.gmail.com, as per these excellent instructions: http://fmuntean.wordpress.com/2008/10/26/how-to-configure-iis-smtp-server-to-forward-emails-using-a-gmail-account/ The local SMTP relay allows anonymous access. Both the local IP and the loopback IP have been explicitly allowed in the Connection and Relay dialogs. Tried sending email from 2 different apps via the local SMTP server, but failed (the emails end up in the Queue folder, but never get sent). The IIS logs show the conversation with the local app, but zero conversation happening with smtp.gmail.com. The port used by gmail is open outbound, and indeed the apps we have that support TLS can send email directly via smtp.gmail.com, so there is no problem with the network. At this point I changed the smtp settings in IIS SMTP server to use a different external SMTP server and hey-presto, the local apps can send email via local IIS SMTP relay. So smtp.gmail.com fails to work with our IIS SMTP relay, but another 3rd party SMTP service works fine. We need to use smtp.gmail.com, so how to troubleshoot this one?

    Read the article

  • Need Suggestions on Backup Strategies and Alternatives?

    - by Leejo
    I'm not sure where else to post this question since it is not exactly Code or Development related...but I know Stackoverflow is a very responsive to questions... Currently, I use Mozy Home to perform an online backup of my laptop. So far, this works well, since I only use one laptop that needs to be backed up. But, soon this may change and I want to explore other alternatives than having to perform an online backup on all machines. Ideally, I want to set up a Network Computer (Laptop/Desktop) with enough storage to hold the backups for all other machines that I would have. Each machine should be responsible for performing their backup (to the Network Computer). This would require some capability like Mozy's incremental backup strategy, but instead of online backup, I would prefer it to be done locally to the Network Computer. Can you recommend a local backup software (backup to a network pc, incremental backup, good restore options)? I'm also looking for any ideas on a local backup strategy even if its different from what I've stated? What works and what doesn't work? Thanks in advance for your help!

    Read the article

  • Cyrus: In practical terms, how do end users administer their shared mailboxes?

    - by Nick
    Let's say we have four customer service reps: Billy, Bob, Joe, and Tom. Tom is the department manager. There's a shared Customer Service mailbox on the Cyrus server that they all have access to. Tom, as the manager also has administrative privileges for the shared mailbox. They decide they want to create sub-folders a certain way, and Tom creates them. They're all running Thunderbird, so Tom right-clicks the main folder and chooses "New Subfolder". Now Tom has the Subfolders he needs and the other sales reps have... nothing! Because Cyrus created the Subfolders giving Tom "Full Access" permissions, and everyone else gets no access. So how does Tom give the other reps in his department access to the new folders? As far as Cyrus is concerned, Tom has permission to grant others access to his new mailboxes- But as far as I can tell, there's no option in Thunderbird for granting mailbox permissions. An IT staff member should not have to receive a support request every time someone wants to add a Subfolder to a shared mailbox. That's why we make certain users into mailbox admins in the first place! But asking (non-technical) users to SSH into an IMAP server to run cyradm seems like a bad idea too. Certainly someone has found a solution for this dilemma. Perhaps a Thunderbird extension for setting Cyrus permissions? Or something like umask that forces subfolders to have identical permissions to their parents on creation? And related, what about Sieve configuration? Is there anyway that can be done from the client machine too? Thanks, Nick

    Read the article

  • Uninstall Perl 5.10 and Install 5.8 on Ubuntu 10.04

    - by user48848
    I was using Ubuntu 8.04 with installed Perl 5.8.8. I had installed Bugzilla 3.4.4 with some custom scripts and it was working fine. I had to upgrade Ubuntu from 8.04 to 10.04 and automatically Perl is also upgraded from Perl 5.8 to 5.10. Now, accessing Bugzilla displays an error message related to Perl module. While trying to run checksetup.pl, I am getting the following error message: root@cvsnew:/var/www/bugzilla-3.4# perl checksetup.pl * This is Bugzilla 3.4.3 on perl 5.10.1 * Running on Linux 2.6.32-24-generic-pae #39-Ubuntu SMP Wed Jul 28 07:39:26 UTC 2010 Checking perl modules... Checking for CGI.pm (v3.33) ok: found v3.48 perl: symbol lookup error: lib/i486-linux-gnu-thread-multi/auto/Digest/SHA/SHA.so: undefined symbol: Perl_Tstack_sp_ptr Accessing Bugzilla throws : "500 Internal Server Error". I explored this issue and found that this issue has come up because upgrading Ubuntu upgrades Perl 5.8 to 5.10 automatically. It seems like Perl 5.10.1 isn't binary compatible with the previous. Now, I want to uninstall Perl 5.10.1 and Install Perl 5.8.8 on my Ubuntu 10.04 box. I will appreciate if someone has already done that or share the required steps/commands to do it.

    Read the article

  • Win 7: apps crash, then explorer crashes, then services fail, then boom

    - by snorfys
    Periodically, every 2-3 days one of my systems will go haywire: every app will crash search will fail via the start menu and then explorer will fail. Restarting explorer via taskmanager will cause it to fail again, then it'll BSOD and restart. The eventlog for when this happens goes something like this every time: ERROR: Session "ReadyBoot" stopped due to the following error: 0xC0000188 (supposedly not a problem) WARNING: The maximum file size for session "ReadyBoot" has been reached... (forget where I found out, but also 'not a problem') ERROR: Session "Circular Kernel Context Logger" stopped due to the following error: 0xC0000188 (again, supposedly not a problem) WARNING: The maximum file size for session "Circular Kernel Context Logger" has been reached... ERROR: Faulting application name: Explorer.EXE, version: 6.1.7600.16450, time stamp:... ERROR: Faulting application name: explorer.exe, version: 6.1.7600.16450, time stamp:... ERROR: Faulting application name: svchost.exe_iphlpsvc, version: 6.1.7600.16385, time stamp:... ERROR: The Service Name service terminated unexpectedly. It has done this 1 time(s) That last one happens a number of times but with a different service name. Then finally we have: ERROR: The Service Control Manager tried to take a corrective action (Restart the service) after the unexpected termination of the Server service, but this action failed with the following error: An instance of the service is already running. After that, I have my BSOD and logs complaining that windows started up without shutting down. It's a new machine: Intel i3 530 4gb RAM (Ran memtest for 4 hrs, no problems) 320GB WD/250GB Seagate HDDs (Happened on fresh installs on 2 separate HDDs) Win7 Pro/Ultimate x64 (wife's copy of pro, my copy of ult, no change) Fresh install + driver and windows update (happened without updates as well) I'm at a bit of a loss as to what I can look at next. Especially since it'll work like a charm for 2-3 days and then it's hooped for a night (I'm on it now in fact - no problems).

    Read the article

  • Redirect specific domains with DNS

    - by user66377
    Currently we filter internet content using OpenDNS, our internal Windows DC/DNS servers point to the router's DNS, which then points to the OpenDNS servers. This works well to block all computer's on the network equally. New issue. We now need to separate what computers can go to what sites. So facebook is blocked for everyone right now, but I need to open it up to the 3 community computers now. The 3 community computers will be on an untrusted network seperate from the company computers so they can have their own DNS server, from their own router. The issue is though they still must connect to the internet using the same IP address. So OpenDNS sees the same IP and blocks them the same way. We are looking into getting a second IP, but it's not likely an option without going up to the next major level with our ISP which we don't want to do. My thought is this. Can I setup a DNS server on the untrusted network, and then depending on the request that comes in, have it send it to either OpenDNS or our ISP's DNS? Example www.facebook.com and www.youtube.com are both on the OpenDNS blacklist. So if they go to www.youtube.com, the local DNS server goes to the ISP's DNS to get the IP and thus the client gets the right IP and can go to the site. This would be manually entered for each allowed site thus creating a white list. Then if they go to www.facebook.com, since the local DNS server does not find an entry, it sends the request to OpenDNS, which then sees the site is on the blacklist, and thus sends the it's blocked webpage. The local DNS server can be either Bind on Linux or MS DNS on Window 2008. If this can be done, can you give some direction as well as I've never setup a DNS such as this before. Thanks

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Excel 2007: Named ranges problems when linking workbooks

    - by Mike
    I've 30+ workbooks each with 5 specific worksheets (formated the same). Each worksheet's data needs to be linked to a master workbook, so that I end up with 5 master workbooks and all the specific data in one long table format $A$2:$I$750. (Are you still with me? ;)) I don't have access to a database, so I'm having to link the sheets to their master workbook directly. I've highlighted the data I need; named the range; and then tried referencing this from my master workbook. I get the #Value error symbol when I try to link (=[WorkbookName]!MyNamedRange) to a cell that doesn't match the top left cell of my range. Example: MyNamedrange is always =$A$2:$I43$ on one specific sheet. On my master workbook it works if it's referenced at A2 but I get #Value if it's referenced A1, or A44. Any ideas? I'm trying to link my data in one continous table so I can run a pivot on it, and other things. Can it be done like this, or should I just copy and paste? I'm trying to keep things 'linked'so I do not need to spend time C&Ping all day. Many thanks Mike.

    Read the article

  • Why can't I copy .zip files from a server to a server in a different domain?

    - by Kyralessa
    At work, we're using a Windows Server 2008 R2 VM as our build server. At the end of the build process for any of our projects, we copy the packaged deployment files to a folder on the server where they'll be deployed. (This is done in a batch command by a service account.) For most of our projects, which deploy to a Windows Server 2008 R2 VM, this step goes swimmingly. But for one project, which deploys to a Windows Server 2003 R2 VM which resides in a different domain on our network, the .zip files return "Access is denied" and don't copy, though all of the other files copy correctly. Our sysadmins say they haven't prevented this in group policy or by other means. If I'm logged in the build server as myself and run the copy in the command window, I can't copy the .zip files over either, so it's not just a matter of the service account's permissions. If I log into the 2003 server and then copy from the build server to the 2003 server, using the command window, it works, whether I run as myself or as our service account. Only .zip files cause the "Access is denied" problem. Even a (fake) .exe file copies correctly. All of our other projects have .zip files, and they copy to their 2008 R2 server correctly. Is there a way I can get the Windows Server 2003 R2 VM to accept .zip files copied from our build server?

    Read the article

  • How does the "Steam" platform work? Is it DRM? Can I trust "Steam"-powered software? [closed]

    - by Chris W. Rea
    So – I just bought the new game Supreme Commander 2. This question is not about the game, but about the online software installation platform that it seems to require. I haven't bought a game in a long time, and I'm puzzled: Apparently, SC2 is a "Steam"-powered game. When I went to install the game, it asked me to either create a new Steam account, or log in with an existing account. I clicked "Cancel" because I don't plan to play online and I don't want anything unnecessary installed on my computer, since I only plan to play single player! However, after clicking "Cancel", the installer asked for my confirmation that I indeed wanted to cancel installation of the game! I thought I was just canceling the "online" portions! So I really want to know: How do "Steam" powered games work? Is this essentially a form of DRM (Digital Rights Management)? Can I trust this software platform? Has anybody done any independent verification on how this platform works? (I'm very leery of any DRM after the Sony BMG CD copy protection scandal. Thank goodness for Mark Russinovich.) Does the "Steam" platform install anything particularly nasty or unwanted on my computer? High-rep users: Please vote to reopen this question. It is not about the game, but about the software update platform / updater / DRM. Imagine if the software in question were a productivity application. The issues remain the same.

    Read the article

  • I accidentally hijacked my localhost

    - by Zach L
    Opening localhost in the browser is pointing a local webpage (examplePage) after playing with some config files a while back, and I can't figure out how to restore the default behavior. Background: I have XAMPP installed on my Windows 7 machine, and a webpage at c:/xampp/htdocs/examplePage. A couple weeks ago, I was on a mission to get sites root-relative urls (/resource) to work, so I played around with a bunch of apache/conf files, including httpd.conf and httpd-vhosts.conf and also was messing with the Windows hosts file. I gave up at some point, didn't document exactly what I did, and have since probably forgotten some of what I did. Many of my changes stemmed from suggestions in this StackOverflow post What I've Tried I commented out my additions to the hosts file I turned off XAMPP (thus hopefully negating any apache config file effect) I reverted to my original DocumentRoot in httpd.conf anyway (xampp/htdocs) localhost still displays examplePage. Even with xampp turned on (my reverted DocmentRootisn't taking effect) Does anyone know what I may have done and how I can fix it? Update : Its been resolved, thank everyone so much in taskmanager, theres a couple instances of httpd.exe (Apache HTTP Server). I ended these, and opened XAMPP, restarting apache. all references to examplePage in my .conf files that I could find had been commented out or removed. I imagine that the old versions were still in effect for some reason, and manually ending the Apache processes fixed this. As a point of interest, Its still a mystery why those processes were running - I cannot reproduce that situation. I must've stumbled upon a XAMPP bug of some sort.

    Read the article

  • who has files open on a linux server

    - by Robert
    I have the fairly common task of finding who has files open on our Linux (Ubuntu ) file server in our Windows environment. We use Samba on the network and I use Putty from my workstation to establish a shell window to run bash scripts. I have been using something like this to find what files are open: (this returns a list of process ids with each open file) Robert:$ sudo lsof | grep "/srv/office/some/folder" Then, I follow up with something like this to show who owns the process: (this returns the name of the machine on the network using the IP4 protocol who owns the process) Robert:$ sudo lsof -p 27295 | grep "IPv4" Now I know the windows client who has a file open and can take action from there. As you can tell this is not difficult but time consuming. I would prefer to have a windows application I can run that would just give me what I want. So, I have been thinking about creating some process I can run on Linux that listens on a port and then returns a clean list of all open files with the IP address of the host who has the file open. Then, a small windows client application that can send the request on the port. It seems like this should be a very common need but I can not find anything like this that has been done before. Any suggestions?

    Read the article

  • IIS7 binding to subdomain causing authentication errors

    - by Tommy Jakobsen
    I'm trying to bind a IIS web site to a subdomain, which is causing authentication errors. First I'll explain what I've done to set it up. This is the fist time I do this, so please correct me if I'm wrong. The web server is a stand-alone Windows Server 2008 R2 x64, running IIS7 with .NET Framework 4. I have the following A-records, pointing to my server: server.mydomain.com *.server.mydomain.com So all subdomains of server.mydomain.com points to the server. In IIS7 I have a web site on port 8080, with a virtual directory (named virtual) that is using Windows Authentication. I have one binding on the web site pointing to all unassigned IP addresses, port 8080 and having a host name of sub.server.mydomain.com. Now, shouldn't I be able to access the virtual directory through: http://sub.server.mydomain.com/virtual That is not working. However, I can access it through: http://sub.server.mydomain.com:8080/virtual But, it won't let me authenticate using a Windows account (Server\Username). A windows account that I can authenticate with, when accessing the site through http://localhost:8080/virtual. What am I missing here?

    Read the article

  • Ubuntu server or Debian server (to run C++ apps developed on Ubuntu)

    - by skyeagle
    I have written a number of C++ server side daemons for my website, using my Ubuntu 9.10 dev machine. The C++ apps I mentioned above are "GUI-less" daemons (and libraries used by the daemons). I am now about to host my website and need to decide whether to go with Debian server or Ubuntu server. In a nutshell, here is the situation: I developed on Ubuntu desktop because I preferred the more friendly GUI I would like to deploy on Debian Server because of the (perceived?) robustness of the Debian server over Ubuntu server (I may be totally wrong here - and in fact, this is really what this question is all about) If Debian server is indeed more robust than Ubuntu server, then I have no choice but to go with Debian server - BUT, will my Ubuntu developed C++ apps run on the server? (or do I need to recompile them on the server? (I'd HATE to have to do this, because I want to keep the server machine clean and light - no GUI, no dev tools etc). This last question is really about binary compatability between Ubuntu and Debian. I want the server to be robust, secure and stable, and simply act as a server (i.e. LAMP and very little else - no GUI etc). Given that requirement, and the fact that I need to run my C++ apps (developed on Ubuntu 9.10), I need advice on which OS to choose for the server. Ideally, any advice will be backed with a reason. I am particularly interested in hearing from people who have been in an identical situation, or done something similar.

    Read the article

  • changing filesystem format from xfs to ext4 without losing data

    - by A.Rashad
    I have a fresh Lucid Lynx (Ubuntu 10.04) running on a laptop. where I defined the filesystems as: mount point / on ext4 (46 Gb) mount point /home on jfs (63 GB) swap as 3 Gb I left the machine over night to do some task, without AC power supply. next day in the morning I found it on standby, task completed, but filesystem was not reachable. it gave me I/O error it seems that there is a problem with jfs and standby. anyways, to avoid any hassle, I want to move this mount point from jfs format to ext4. can I do this without losing data and without the need to place the data in a temporary location until transformation is done? sorry to mention that, but I recall back in the windows days, we would change a FAT16 to FAT32 or a FAT32 to NTFS without having to lose the data. I hope this is available on Linux. Update The /home filesystem was xfs not jfs, and it seems there is a bug with this filesystem for some reason, I had to re-install the OS twice until I ended up with ext4 for the entire / However, as a conclusion, it seems that there is no way to make a conversion

    Read the article

  • Multicast image restoration with adaptive speed

    - by Clinton Blackmore
    I'm curious to know if there are any tools for restoring disk images (or even transferring files) via multicast -- for any platform, especially if the project has source available -- where the multicast rate adjusts itself on the fly. On the Mac, all multicast solutions I am aware of (such as Deploy Studio, and NetRestore before it) make use of multicast ASR (apple software restore), which has one glaring deficiency -- you have to set the multicast speed before you start sending a disk image over the network, and that speed is locked in. Either your clients can keep up and restore, or they can't*. It seems to me that it must be possible for the multicast server to adjust the data rate, so you basically say "start sending this image", clients connect, and, if they can't keep up, they tell the server so it slows down. (Likewise, I'd expect the server to try speeding up if no client is having difficulties keeping up, and I'd expect to be able to cap that maximum throughput so that other network activities can go on without being resource starved.) So, what sort of tools are out there? For Linux? Windows? Is there something for the Mac I've overlooked. [It just kills me that it is true that, by the time you get multicast up and going at a good speed to restore a lab, you could've unicasted the data to all the computers and be done.] * There is a little leeway involved. I think individual clients can say, "I missed a little bit of data" and get it, and they can opt to listen in the next time the image is sent over the network, but on the whole, if they missed it the first go round, you have to image the machine again, and there is no time savings.

    Read the article

  • Windows 7 Folder Redirection (GPO)

    - by Kev
    I have been fighting this issue for a day or two now, so I am looking for some insight. I am taking over admin duties in a domain of 800 users, and the previous admins really did not employ much of any GPO settings for the clients of the Domain. In each site, there is a location on the file server where "Home" folders were manually created. EX: \server\home\enduser Whenever a user got a machine, the admin would manually right-click on the "My Documents" folder and manually enter the path to the home folder. We are planning to start putting Windows 7 machines on the Network, and I am wanting to automate as much as I can, everything that was not done in the past. Since everyone has exising "Home" folders I have been fighting and trying to get Folder Redirection to work with a new Windows 7 machine (In a Test OU). I am getting all kinds of errors and I can't get the Windows 7 "Documents" folder to redirect to the users EXISTING home folders. As I stated earlier, all of the Home folders were (and still are) manually created on the File Server and are set with the following Security permissions - Domain Admins - Full Control euser (end user) - Modify (Everything but Full) Can someone point me in the right direction on the proper setting to put in the Folder Redirection GPO to get this to work with the Existing Home folders.

    Read the article

< Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >