Search Results

Search found 2370 results on 95 pages for 'av cable'.

Page 66/95 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• How to use 3T SAS HDDs which aren't supported by Dell PERC 6i

  - by Sunry

  We bought several 3T SAS hard disks want to use with our Dell R710 server. But we found our R710 can't recognize the 3T hd, and then we dig out the raid card is PERC 6i which doesn't support it. Contacted with Dell that H700 and H800 support 3T hd, thought we can buy a H700 , but the SAS cable is not available in the market right now. And it seems very hard for us to change the raid card, also no suitable tools to tease the special screws. So I want to know if any other method to use these 3T hds instead of putting them in the warehouse? Can I low formatting it to 2TB, and plug it into Dell R710 to use? Or a SAS to USB adapter to use it as USB external disk? I just want to use them by Dell R710 even external.

  Read the article

• How can I troubleshoot SSD disconnection problems on Windows 7?

  - by 0xC0000022L

  I have a small SSD (Transcend StoreJet TS256GESD200K) which I am using on several computers. The drive is formatted with NTFS and recently I started noticing disconnects. Normally one probably wouldn't notice (you don't even get the notification sound in Windows when it disconnects), but since I use USBDLM and run a VM from that SSD, I get to see this first-hand. How could I best figure out whether the problem is the hardware (SSD, USB socket, USB cable or something in the PC) or software? In short: how can I locate the source of the disruption so that I can work on removing the problem? Side-note: SMART status for the SSD is clean.

  Read the article

• Able to ping but does not get the data

  - by Dany

  I am facing a problem in my client server program; when using wireless I can ping but not receive any data. There is a source which receives a streaming request from client via server. This works fine when all the machines are connected through LAN cable but when I put all the computers in wi-fi network, all the machine are able to ping each other but when the client send the stream request to the server the ping request between server and client says destination unreachable. It works all well until the client does not send the streaming request. What might be the issue?

  Read the article

• My MacBook Pro (2011) is dead

  - by Dave

  I connected my Sony digital camera with the MacBook and the screen turned black. I wonder why because the Sony camera was not on at the time and technically could not be accessed. So I thought it might be temporary and I turned on my camera. Well, it did not work, but my MacBook Pro has been dead since then. It will not turn on - when I hold the power button for five seconds, nothing happens. When I connect the charger cable, the green light is very dim and blinks a little (with about 20% illumination). I wonder what the problem is. I have to call Apple Care, but just so that I know, what could be wrong? Is my MacBook permanently dead? It might be under warranty but I am not sure.

  Read the article

• How to route packets from Wi-Fi to Ethernet on OSX?

  - by Alexander Artemenko

  I have a trouble, configuring a home network. Here is how my devices are connected together: Internet     ? Wi-Fi Router ? MacBook     ? iMac ?ethernet cable? Synology NAS I have no ability to plugin NAS right into the Wi-Fi router. The problem is that MacBook does not see NAS, because they are in different networks — I configured Wi-Fi Router to serve 192.168.10.0/24 addresses, and configured iMac's ethernet connection to use 192.168.20/24 network. Is there a way to setup route from MacBook to the NAS?

  Read the article

• Multiple monitors on ATI Radeon HD 5450 1GB DDR2 (Brand: Sapphire)

  - by Robert

  From other posts here, I understand that it might be possible to use up to 3 monitors on this card. My understanding (from the other posts here as well) is that since I have a HDMI output, I do not have a 'DisplayPort', right ? Mine has indeed 3 ports: DVI, HDMI and VGA. Can I have dual-monitor using both the HDMI and DVI ports simulataneously (I am not looking for Eyefinity, but simply extended desktop). Currently I am using dual monitor with DVI and VGA but will replace my 17 inches next week with a new (larger) one that has both VGA and DVI, so I intend to use both monitors connected digitally. I intend to purchase a cable ''HDMI to DVI''(MM) to do so on the second monitor. Optimal resolution on the one I intend to keep (22 inches) : 1680 x 1050, primary monitor. New one (24 inches) has an optimal resolution of 1920 x 1080. Am I running for problems ? Thanks, Rob

  Read the article

• Which method of SQL Server 2005 or 2008 Replication is best for ease of field changes?

  - by Rick

  We need 15 minute warm updates from one SQL Server to another. Log Shipping looks good and appears easy to setup. We are also looking into Transactional Replication. The data only needs to copy one way. We have two main requirements: 1) The destination database needs to be a max 15 minute old copy of the source. It needs to re-try and get up-to-date if a network cable is unplugged for a while. 2) We would really like table (fields added or modified) changes in the source as easy as possible. Thanks in advance for all suggestions.

  Read the article

• Media Center is sending duplicate #'s when changing channels

  - by Robert

  I recently switched from cable to DirecTV (satellite). I went through the "Set up TV signal" in Media Center, and I went through the manual setup of the remote as it didn't recognize the DirecTV remote. All seemed okay, except sometimes (often - about 1/2 the time) when I select a channel in Media Center's guide it sends 5527 instead of 527 or 5446 instead of 546 - so it doesn't change the channel correctly. (I see the numbers show up on the TV screen before the channel changes.) I tried re-learning the remote, but the problem is still there. (Media Center is changing channels through the IR Blaster attached to the front of the DirecTV box.)

  Read the article

• How do I record sound from my CD/DVD player without other system sounds in the mix?

  - by Software Monkey

  Using GoldWave I can record via the "Stereo Mix" channel, but I get no sound on the "CD" channel. Of course, using the stereo mix also mixes in all system sounds, including beeps, etc. I have the analog out on the DVD player connected to the CD-IN connector on the MoBo. I can hear CDs and DVDs playing just fine through my speakers - is this because the CD is also IDE data connection in to deliver the sound to the sound card, then? I specifically want to record a DVD; I can easily rip a CD using GoldWave's built-in ripper. Is there anything I have forgotten or have to enable? Or is it likely I have a damaged cable? My system is an MSI mobo and is running Windows XP SP3.

  Read the article

• Using video ports 'backwards'

  - by ACarter

  If I want to connect my laptop, which has a VGA output, to a monitor, I plug a VGA cable into both ends. The output being my laptop, and the input the monitor VGA output sockets are the same as VGA input sockets however, so what if I want to use my laptop as the monitor, with the video being outputted from somewhere else? As I said, VGA's output is the same as input, so in theory, I have the hardware in my laptop to do this. But presumably I need some software. So can I use the VGA port on a laptop as a video input? (And also, can this be done with HDMI?)

  Read the article

• Pentium 4 Computer Won't Power Up

  - by Harvey

  I have a faulty Pentium 4 workstation with data that I would like to retrieve. Here are the symptoms & what I've done so far: Machine is totally dead. Motherboard LED is lit but that is the only sign of life. I have replaced the power supply and bypassed the on/off switch. Tried a PC Analyzer motherboard tester but didn't have any power to the card. Unpluggged the P4 cable from the motherboard, hit the on/off switch, the power supply fan comes on and I get codes from the analyzer but nothing that seems to be of any value. Machine does not boot. Will not shut down by hitting the switch. Bad motherboard or could it be a bad CPU cooling fan?

  Read the article

• Run disk error check on NTFS file?

  - by paulius_l

  I have a feeling that my system hard drive is dying. Benchmark kind of enforces it. Here is the benchmark of my system hard drive during low system activity: And here is the benchmark of backup drive: Furthermore, there are some files which I just can't touch because I get CRC errors and the hard drive activity spikes to 100% with operating speeds less than 1 MB/s while working with such files. I haven't yet tried swapping SATA cable as I have read this might cause the problems. Anyway, I would like to run some tests on specific clustsers where those files I am interested in are stored. I don't want to do the full chkdsk because it takes a very long time. I would like to either find the utility which executes the disk check directly on the clusters where the file belongs or a couple utilities where one tells me the cluster locations and another can check just those locations. How do I check and possibly fix disk errors where the files I am interested in are stored? Edit: S.M.A.R.T. info:

  Read the article

• Setting Screen Resolution for Extended Display on Windows 8

  - by ptamzz

  I'm using a Dell Inspiron laptop with Windows 8 Developers Preview. I've connected a second screen (some Dell 22 inch one) and have been using it with 'Extend these displays' options in the Screen Resolution settings. It use to be all fine but yesterday I changed my VGA cable to the 2nd monitor and since then the resolution of the 2nd monitor is not setting properly. Earlier, while auto detecting the monitor, the right resolution use to appear but now, as you can see from the attached image, none of the resolution in the drop down fits with the right proportion. So how do I set the right screen resolution. (I think the right one is 1680 x 1050 which is not there in the list)

  Read the article

• Can connect to WAN via PC but router doesnt.

  - by user16877

  I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

  Read the article

• HDMI and DVI connected monitors not in dual view on Windows 7 (Intel onboard Gigabyte)

  - by Nux

  I have a HDMI to DVI cable which is connected to one monitor (HDMI is on PC side) and DVI-DVI connected to other monitor. This seems to work up until the system is fully loaded (the startup logo animation is shown on two screens). When and after I log in only one monitor is active (HDMI-DVI). I'm also unable to detect the other monitor (DVI-DVI). Any ideas what might be wrong with the setup? Also when I uninstall the Intel Graphics driver both screens are on, but only duplication works. GA-Z68A-D3H-B3, Intel Z68 Chipset, with fresh VGA driver (15.26.1.64.2618).

  Read the article

• How to force 640*480@60Hz screen resolution on xubuntu 12.04

  - by c2h2

  It seems xubuntu won't be able to correctly set resolution at 640*480@60Hz at its Display settings. And I am unable to correctly my super small 6.4 inch Mitsubishi VGA panel via VGA cable. I have tried to hack both X11 conf /etc/X11/Xorg.conf and xfce4 conf, but all the document I can find is outdated. and conf files are changed into other location. Can someone give me a hand and I'll mark correct for other people to use? Thanks! EDIT: The board is an Intel Atom D2700, gpu is SGX545. I tried to use xrandr --output default --mode 640*480 It seems works fine, but refresh rate is 75Hz, but the screen only suports 60Hz So I used xrandr --output default --mode 640*480 --rate 60 but it give error: xrandr: Failed to get size of gamma for output default Can anyone pointing any directions?

  Read the article

• How to set up Asus RT-N66U in bridge mode with wired connection to main router?

  - by Milligan

  I have a wired router (TP-Link RT-860) in the basement where the cable service comes in. Eight wired ethernet connections span two buildings. I currently have a Linksys wireless router set up in bridge mode, but its signal doesn't span the whole area. I have purchased an Asus RT-N66U to replace it, but I can't figure out how to set it up in bridge mode. Does anyone know if this is possible? Second question: Would there be any advantage in installing DD-WRT on the Asus?

  Read the article

• Trouble with external monitor under Windows 7 on MacBook Pro Boot Camp

  - by Colm

  I'm running Windows 7 32-bit on a mid-2010 15" MacBook Pro Intel Core i5 under Boot Camp. I've had trouble getting it to work with my second display and searching Google for an appropriate answer has failed me. I'm on the latest version of Boot Camp - 3.2 - and have updated the drivers for the NVIDIA GeForce GT 330M. The monitor is connected via a VGA cable, and is a Dell ST2410. The monitor is recognised by Windows, which knows it's a Dell and its resolution. The desktop should be extended onto the second monitor - however nothing is showing. It remains black, though it doesn't show a lack of signal coming through which I would have expected. Any ideas what's wrong?

  Read the article

• Any experience with SATA SAS Interposer Cards?

  - by korkman

  Driven by the current price difference between SATA and SAS disks on one side and the potentially bad behaviour of SATA disks in bigger storage arrays on the other side, I have found so-called SATA-to-SAS interposer cards. Advertised as "seamlessly adding SAS capabilities to existing SATA disk drives", I wonder if anyone here has had some experience with these or similar products. The major benefits I can identify are the increased cable voltage (if all drives are SAS connected), the ability to power-cycle the drive and multipath (if desired). Obviously the SATA drive will still have to be RAID edition. The question is: Do these cards indeed increase the overall reliability of a storage system, or will failing SATA disks cause trouble nevertheless? Edit: I'm not asking for hypothetical answers, only actual experience please. I'm well aware that the typical 10k SAS drive is more reliable (and better performing) than 7200 SATA drives. But how does a nearline SAS, which is phyiscally the same disk as its SATA counterpart, compare to the SATA version with interposer?

  Read the article

• Can I use only a HDMI monitor?

  - by Felix

  I recently found out there are such things as PC monitors with TV capabilities (or TVs that can be PC monitors), and the idea kind of tickles my fancy. I'm thinking of getting one of these gadgets, and if I do, I will connect it to my PC via HDMI (my graphics card has builtin HDMI), so that I also get sound to the TV. The reason for this is because I have a 2.1 sound system which I want to use both on the PC and the TV. Basically, I want the configuration to look like this: Cable --------> TV --> 2.1 Sound System PC --HDMI--> TV --> 2.1 Sound System My question is: can I use a setup like this? Can I not have a classic VGA monitor? Will I be able to see non-graphical interfaces (such as the BIOS, GRUB, a Linux terminal, ...) through HDMI on the TV? I use Windows 7 and Ubuntu.

  Read the article

• OpenBSD Routing Problem

  - by Ozkan SENOVA

  I am running OpenBSD on a network appliance hardware. It has 5 NICs. I want to give different IP's in same subnet to 3 nics. Eg: em0: 192.168.1.5 em1: 192.168.1.90 em2: 192.168.1.56 I make the necessary configuration with ifconfig, all interfaces works as expected when all the ethernet ports are plugged in to switch. But there is something wrong in routing. If I connect to 192.16.1.5 via any service(http, smtp etc.), traffic goes over link#3. If I unpug the cable from em2 I can't reach any IP's binded on device. Is there any way to route traffic over different links in this IP configuration?

  Read the article

• Connect two devices with ethernet

  - by mofle

  I have a MacBook Pro and I'm going to buy a Boxee Box. I have access to wireless internet, but it's slow and out of my control. So my question is, what is the best way for both devices to get internet access, and the Boxee Box to get SMB access to the Mac, when only the Mac is connected to the wireless internet? I'm thinking an ethernet cable from the Boxee Box to my Mac, and connection sharing on my Mac. Can you explain the setup, is there any configuring.

  Read the article

• Can I use the Airport Express as a an uplink between two networks?

  - by Ant Swift

  I have two separate networks using different IP ranges, 192.168.0.* for the wired only, isolated network and 192.160.1.* for the wireless only network which is connected to the internet. The wired network has a network printer setup and working and I want to be able to share it out to members of the wireless network (see diagram below). In short I need some kind of uplink between the two networks. Currently running a cable is out since there is no suitable route. I have a spare Airport Express and I am wondering if I could attach it to the wired network and have it join the wireless and act as the uplink between the two. Anyone know if the device is capable of this?

  Read the article

• Connecting a print/file server with no wired access

  - by PeanutsMonkey

  We currently have a printer server which also serves as a file server. The server is located on premise however is not close to any wired access point i.e. a patch panel or point. The server also requires access to the Internet as it transmits files across. We have a wireless modem and a wireless router. I can run a cable between the server and wireless router. How can I have the wireless router communicate with the wireless modem? If the operating system of the server is concerned, it is running Windows Server 2003.

  Read the article

• Slow write speeds on new Gigabit home file server

  - by Ryan Holder

  So I finally got all my parts delivered to setup a home file/backup server this week. It's currently running Ubuntu Server and I'm using Samba to share files on my network. The server currently has a 2TB WD Green drive in it connected to a Asus M5A78L-M This is then connected via CAT6a to my new Gigabit switch (TP-Link TL-SG1005D). My home desktop is then also connected to this switch and again also through CAT6a cable. Currently when transfering files I will get a perfect 100MB/s read from the server to my Windows machine. When copying from my Windows machine to the server I get around 30/38MB/s. I know this drive is capable is faster speeds so would anybody have an idea of where the bottleneck is? Any help would be greatly appreciated :) EDIT: I have found ftp's write speed is much closer to what my Samba read speed is so I'm going to give it a guess that is a software problem rather than hardware

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >