Search Results

Search found 7647 results on 306 pages for 'dann dev'.

Page 66/306 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• smartctl not actually running self tests?

  - by canzar

  I want to run the smartctl self tests to check the health of the drives in my RAID array (PERC 5/i). The array is on sda and comprises six drives. I can check the status using sudo smartctl /dev/sda -d megaraid,0 -a And I see that SMART is available and enabled on all the drives. I have tried to run self tests using sudo smartctl /dev/sda -d megaraid,0 -t short and sudo smartctl /dev/sda -d megaraid,0 -t long I have also tried it on all of the drives 0-5. No matter what I try, when I run: sudo smartctl /dev/sda -d megaraid,0 -l selftest I always get the same result, which seems to always report that I have never run a self test. /dev/sda [megaraid_disk_00] [SAT]: Device open changed type from 'megaraid' to 'sat' ===START OF READ SMART DATA SECTION === SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] From what I read, I should have no problem running the short and long self tests on the array while it is mounted. Does anyone else have experience running these tests on a PERC 5/i raid array who could lend some insight into what is causing the problem? (smartmontools release 5.40 dated 2009-12-09 at 21:00:32 UTC)

  Read the article

• Why do I get xfs_freeze "Operation not supported" error with ec2-consistent-snapshot? Debian Squeeze w/ext4 filesystem

  - by Michael Endsley

  I'm running the following command: [root@somehost ~]# ec2-consistent-snapshot --aws-credentials-file '/some/dir/file' --mysql --mysql-socket '/var/run/mysqld/mysql.sock' --mysql-username 'backup' --mysql-password 'password' --freeze-filesystem '/dev/xvda1' vol-xxxxxx It returns this error: xfs_freeze: cannot freeze filesystem at /dev/xvda1: Operation not supported ec2-consistent-snapshot: ERROR: xfs_freeze -f /dev/xvda1: failed(256) snap-eeb66393 xfs_freeze: cannot unfreeze filesystem mounted at /dev/xvda1: Invalid argument ec2-consistent-snapshot: ERROR: xfs_freeze -u /dev/xvda1: failed(256) This is being run on Debian Squeeze with the ext4 Linux filesystem. Can anyone explain this error to me, or what might be its cause? When googling, I found information about it needing to be executed with sudo, but I'm performing the entire operation as root. I also found some posts about trying to run it after a CentOS upgrade using yum, but the situation appeared dissimilar. It's difficult to find things referring to this situation exactly. xfs_freeze is available for use on the filesystem. Is it possible that the filesystem, despite being ext4, somehow doesn't support freezing? Sorry if I've missed some bit of StackExchange etiquette with this post -- it's my first venture here!

  Read the article

• How do I usb tether my Cyanogen modded G1's internet connection to my Toshiba Tecra 8000 running Xub

  - by atticus

  I have usb-tethering enabled in my phone. It works fine with Vista. When I plug my phone into my Tecra 8000 laptop running Xubuntu, dmesg shows: "usb 1-1: new full speed USB device using uhci_hcd and address 8". I see that the OS has detected it as a storage device, but I can't get it to function correctly as a network device. /dev/us* shows no usb0, but it does show /dev/usbdev1.1_ep00 /dev/usbdev1.1_ep81 /dev/usbdev1.8_ep00 ... usbdev1.8_ep83. I could just use the wireless tether app for android, but I can't get my Netgear wg511 v2 (made in China) wireless card to work in this laptop either. But that's another post for later.

  Read the article

• Can't manage iPod from linux anymore

  - by kemp

  I used to be able to see and manage my iPod with different softwares: Amarok, Rhythmbox, GTKPod. The device is a nano 1st generation 4gb. Currently it mounts regularly and can be accessed from the file system, but I get this in dmesg: [ 1547.617891] scsi 11:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 [ 1547.619103] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 1547.620478] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.620494] sd 11:0:0:0: [sdb] 7999487 512-byte hardware sectors: (4.09 GB/3.81 GiB) [ 1547.621718] sd 11:0:0:0: [sdb] Write Protect is off [ 1547.621726] sd 11:0:0:0: [sdb] Mode Sense: 68 00 00 08 [ 1547.621732] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.623591] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.624993] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.625003] sdb: sdb1 sdb2 [ 1547.629686] sd 11:0:0:0: [sdb] Attached SCSI removable disk [ 1548.084026] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.369502] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.504358] FAT: invalid media value (0x2f) [ 1548.504363] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1548.945173] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.945179] FAT: invalid media value (0x2f) [ 1548.945182] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1610.092886] usb 2-6: USB disconnect, address 9 The only application that can access it (partially) is Rhythmbox. I say partially because I can transfer files to the iPod but can't remove or modify them. Also one transfer didn't finish and only 9 out of 16 songs were delivered to the device. All other softwares I tried (GTKPod, Amarok, Songbird) don't even detect it. What can I do to troubleshoot this? EDIT: # fdisk -l /dev/sdb Disk /dev/sdb: 4095 MB, 4095737344 bytes 241 heads, 62 sectors/track, 535 cylinders Units = cylinders of 14942 * 512 = 7650304 bytes Disk identifier: 0x20202020 Device Boot Start End Blocks Id System /dev/sdb1 1 11 80293+ 0 Empty Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 1, 1) logical=(0, 1, 2) Partition 1 has different physical/logical endings: phys=(9, 254, 63) logical=(10, 181, 8) Partition 1 does not end on cylinder boundary. /dev/sdb2 11 536 3919415+ b W95 FAT32 Partition 2 has different physical/logical beginnings (non-Linux?): phys=(10, 0, 7) logical=(10, 181, 15) Partition 2 has different physical/logical endings: phys=(497, 240, 62) logical=(535, 88, 61) EDIT2: The "before" state is hard to tell, it was a lot of updates ago. Haven't been using my iPod for a while so I can't say when exactly it stopped working. I'm sure Amarok was still at version 1.X but can't remember when it was. My current system is debian testing fully updated. NOTE: just noticed that if I mount the device manually instead of letting nautilus automount it, I can see it again on GTKPod but still not on Banshee AND it's vanished from Rhythmbox...

  Read the article

• Limiting bandwidth on internal interface on Linux gateway

  - by Jack Scott

  I am responsible for a Linux-based (it runs Debian) branch office router that takes a single high-speed Internet connection (eth2) and turns it into about 20 internal networks, each with a seperate subnet (192.168.1.0/24 to 192.168.20.0/24) and a seperate VLAN (eth0.101 to eth0.120). I am trying to restrict bandwidth on one of the internal subnets that is consistently chewing up more bandwidth than it should. What is the best way to do this? My first try at this was with wondershaper, which I heard about on SuperUser here. Unfortunately, this is useful for exactly the opposite situation that I have... it's useful on the client side, not on the Internet side. My second attempt was using the script found at http://www.topwebhosts.org/tools/traffic-control.php, which I modified so the active part is: tc qdisc add dev eth0.113 root handle 13: htb default 100 tc class add dev eth0.113 parent 13: classid 13:1 htb rate 3mbps tc class add dev eth0.113 parent 13: classid 13:2 htb rate 3mbps tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip dst 192.168.13.0/24 flowid 13:1 tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip src 192.168.13.0/24 flowid 13:2 What I want this to do is restrict the bandwidth on VLAN 113 (subnet 192.168.13.0/24) to 3mbit up and 3mbit down. Unfortunately, it seems to have no effect at all! I'm very inexperienced with the tc command, so any help getting this working would be appreciated.

  Read the article

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• perl hide system output

  - by Chris

  Using perl 5.8.8 on linux, need the output of a perl 'system' command to be hidden. The command in my code is : system("wget", "$url", "-Omy_folder/$date-$target.html", "--user-agent=$useragent"); I've tried using " /dev/null 2&1" in different places in the system command, like this- system("wget", "$url", "-Omy_folder/$date-$target.html", "--user-agent=$useragent"," /dev/null 2&1"); Can anyone help me with where the redirection to /dev/null should be?

  Read the article

• 6to4 tunnel: cannot ping6 to ipv6.google.com?

  - by quanta

  Hi folks, Follow the Setup of 6to4 tunnel guide, I want to test ipv6 connectivity, but I cannot ping6 to ipv6.google.com. Details below: # traceroute 192.88.99.1 traceroute to 192.88.99.1 (192.88.99.1), 30 hops max, 40 byte packets 1 static.vdc.vn (123.30.53.1) 1.514 ms 2.622 ms 3.760 ms 2 static.vdc.vn (123.30.63.117) 0.608 ms 0.696 ms 0.735 ms 3 static.vdc.vn (123.30.63.101) 0.474 ms 0.477 ms 0.506 ms 4 203.162.231.214 (203.162.231.214) 11.327 ms 11.320 ms 11.312 ms 5 static.vdc.vn (222.255.165.34) 11.546 ms 11.684 ms 11.768 ms 6 203.162.217.26 (203.162.217.26) 42.460 ms 42.424 ms 42.401 ms 7 218.188.104.173 (218.188.104.173) 42.489 ms 42.462 ms 42.415 ms 8 218.189.5.10 (218.189.5.10) 42.613 ms 218.189.5.42 (218.189.5.42) 42.273 ms 42.300 ms 9 d1-26-224-143-118-on-nets.com (118.143.224.26) 205.752 ms d1-18-224-143-118-on-nets.com (118.143.224.18) 207.130 ms d1-14-224-143-118-on-nets.com (118.143.224.14) 206.970 ms 10 218.189.5.150 (218.189.5.150) 207.456 ms 206.349 ms 206.941 ms 11 * * * 12 10gigabitethernet2-1.core1.lax1.he.net (72.52.92.121) 214.087 ms 214.426 ms 214.818 ms 13 192.88.99.1 (192.88.99.1) 207.215 ms 199.270 ms 209.391 ms # ifconfig tun6to4 tun6to4 Link encap:IPv6-in-IPv4 inet6 addr: 2002:x:x::/16 Scope:Global inet6 addr: ::x.x.x.x/128 Scope:Compat UP RUNNING NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:11 dropped:0 overruns:0 carrier:11 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) # iptunnel sit0: ipv6/ip remote any local any ttl 64 nopmtudisc tun6to4: ipv6/ip remote any local x.x.x.x ttl 64 # ip -6 route show ::/96 via :: dev tun6to4 metric 256 expires 21332777sec mtu 1480 advmss 1420 hoplimit 4294967295 2002::/16 dev tun6to4 metric 256 expires 21332794sec mtu 1480 advmss 1420 hoplimit 4294967295 fe80::/64 dev eth0 metric 256 expires 15674592sec mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth1 metric 256 expires 15674597sec mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tun6to4 metric 256 expires 21332794sec mtu 1480 advmss 1420 hoplimit 4294967295 default via ::192.88.99.1 dev tun6to4 metric 1 expires 21332861sec mtu 1480 advmss 1420 hoplimit 4294967295 # ping6 -n -c 4 ipv6.google.com PING ipv6.google.com(2404:6800:8005::68) 56 data bytes From 2002:x:x:: icmp_seq=0 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=1 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=2 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 4 packets transmitted, 0 received, +4 errors, 100% packet loss, time 2999ms What is my problem? Thanks,

  Read the article

• Xen kernel can't see 2 disks of 6 of 1TB, does it have a limitation?

  - by PartySoft

  Linux gentoo-xen 2.6.18-xen-r12 #3 SMP Tue Oct 5 09:28:53 PDT 2010 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux I have 6 disks of 1 TB and i can't see all of them only 4, can anyone give me an ideea what can i do ? Filesystem Size Used Avail Use% Mounted on rootfs 886G 4.4G 836G 1% / /dev/sda3 886G 4.4G 836G 1% / rc-svcdir 1.0M 44K 980K 5% /lib64/rc/init.d shm 7.9G 0 7.9G 0% /dev/shm /dev/sdb1 917G 200M 871G 1% /home2 /dev/sdc1 917G 200M 871G 1% /home3 /dev/sdd1 917G 200M 871G 1% /home4 The hardware is Dual xeon E5506 processors on a supermicro X8DTL mobo 4.346585] ata3.00: ATA-8, max UDMA/133, 1953525168 sectors: LBA48 NCQ (depth 0/32) [ 4.346588] ata3.00: ata3: dev 0 multi count 16 [ 4.352861] ata3.00: configured for UDMA/133 [ 4.352867] scsi3 : ata_piix [ 4.352875] PM: Adding info for No Bus:host3 [ 4.510584] ata4.00: ATA-8, max UDMA/133, 1953525168 sectors: LBA48 NCQ (depth 0/32) [ 4.510587] ata4.00: ata4: dev 0 multi count 16 [ 4.516848] ata4.00: configured for UDMA/133 [ 4.516861] PM: Adding info for No Bus:target2:0:0 [ 4.516905] Vendor: ATA Model: SAMSUNG HD103SJ Rev: 1AJ1 [ 4.516910] Type: Direct-Access ANSI SCSI revision: 05 [ 4.516920] PM: Adding info for scsi:2:0:0:0 [ 4.517452] SCSI device sde: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.517460] sde: Write Protect is off [ 4.517461] sde: Mode Sense: 00 3a 00 00 [ 4.517478] SCSI device sde: drive cache: write back [ 4.517514] SCSI device sde: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.517521] sde: Write Protect is off [ 4.517522] sde: Mode Sense: 00 3a 00 00 [ 4.517532] SCSI device sde: drive cache: write back [ 4.517534] sde: sde1 [ 4.524551] sd 2:0:0:0: Attached scsi disk sde [ 4.524855] sd 2:0:0:0: Attached scsi generic sg4 type 0 [ 4.524874] PM: Adding info for No Bus:target3:0:0 [ 4.524928] Vendor: ATA Model: SAMSUNG HD103SJ Rev: 1AJ1 [ 4.524933] Type: Direct-Access ANSI SCSI revision: 05 [ 4.524946] PM: Adding info for scsi:3:0:0:0 [ 4.525216] SCSI device sdf: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.525227] sdf: Write Protect is off [ 4.525228] sdf: Mode Sense: 00 3a 00 00 [ 4.525242] SCSI device sdf: drive cache: write back [ 4.525280] SCSI device sdf: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.525286] sdf: Write Protect is off [ 4.525289] sdf: Mode Sense: 00 3a 00 00 [ 4.525301] SCSI device sdf: drive cache: write back [ 4.525302] sdf: sdf1 [ 4.532691] sd 3:0:0:0: Attached scsi disk sdf [ 4.533010] sd 3:0:0:0: Attached scsi generic sg5 type 0 [ 4.977669] scsi: <fdomain> Detection failed (no card) [ 5.030479] GDT-HA: Storage RAID Controller Driver. Version: 3.05 [ 5.030635] GDT-HA: Found 0 PCI Storage RAID Controllers [ 5.372350] Fusion MPT base driver 3.04.01 [ 5.372358] Copyright (c) 1999-2005 LSI Logic Corporation [ 5.579176] Fusion MPT SPI Host driver 3.04.01 [ 5.881777] ieee1394: Initialized config rom entry `ip1394' [ 6.166745] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [ 6.166748] ieee1394: sbp2: Try serialize_io=0 for better performance [ 6.428866] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 [ 6.428872] md: bitmap version 4.39 [ 6.431518] md: raid0 personality registered for level 0 [ 6.495979] md: raid1 personality registered for level 1 [ 6.570270] raid5: automatically using best checksumming function: generic_sse [ 6.575523] generic_sse: 6608.000 MB/sec [ 6.575526] raid5: using function: generic_sse (6608.000 MB/sec) [ 6.596226] raid6: int64x1 1835 MB/s [ 6.613231] raid6: int64x2 1773 MB/s [ 6.630256] raid6: int64x4 1675 MB/s [ 6.647296] raid6: int64x8 1027 MB/s [ 6.664267] raid6: sse2x1 3578 MB/s [ 6.681268] raid6: sse2x2 4207 MB/s [ 6.698280] raid6: sse2x4 4625 MB/s [ 6.698281] raid6: using algorithm sse2x4 (4625 MB/s) [ 6.698285] md: raid6 personality registered for level 6 [ 6.698286] md: raid5 personality registered for level 5 [ 6.698288] md: raid4 personality registered for level 4 [ 6.781090] md: raid10 personality registered for level 10 [ 7.007043] Intel(R) PRO/1000 Network Driver - version 7.1.9-k4 [ 7.007046] Copyright (c) 1999-2006 Intel Corporation. [ 9.229465] kjournald starting. Commit interval 5 seconds [ 9.229476] EXT3-fs: mounted filesystem with ordered data mode.

  Read the article

• external hard drive is no longer recognized, gives buffer I/O errors

  - by BioGeek

  Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

  Read the article

• How to mount vfat drive on Linux with ownership other than root?

  - by Norman Ramsey

  I'm running into trouble mounting an iPod on a newly upgraded Debian Squeeze. I suspect either a protocol has changed or I've tickled a bug, which I don't know where to report. I'm trying to mount the iPod so that I have permission to read and write it. But my efforts come to nothing: $ sudo mount -v -t vfat -o uid=32074,gid=6202 /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control $ sudo umount /mnt $ sudo mount -v -t vfat -o uid=nr,gid=nr /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control As you see, I've tried both symbolic and numberic IDs, but the files persist in being owned by root (and only writable by root). The IDs are really mine; I've had the UID since 1993. $ id uid=32074(nr) gid=6202(nr) groups=6202(nr),0(root),2(bin),4(adm),... I've put an strace at http://pastebin.com/Xue2u9FZ, and the mount(2) call looks good: mount("/dev/sde2", "/mnt", "vfat", MS_MGC_VAL, "uid=32074,gid=6202") = 0 Finally, here's my kernel version from uname -a: Linux homedog 2.6.32-5-686 #1 SMP Mon Jun 13 04:13:06 UTC 2011 i686 GNU/Linux Does anyone know if I should be doing something different, or If there is a workaround, or If this is a bug, where it should be reported?

  Read the article

• linux refused to mount a valid partition

  - by greg

  My setup is a linux box with 1 partition used thought LVM - has been working for years. I add a freeze and after the reboot the partition cannot be mounted: mount -r -t ext3 /dev/pve/data /mnt/pve-data mount: wrong fs type, bad option, bad superblock on /dev/mapper/pve-data, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so However fsck doesn't see any problem with it: fsck.ext3 -fp /dev/pve/data /dev/pve/data: 3024076/60366848 files (0.6% non-contiguous), 156921642/241435648 blocks There's nothing in dmegs nor the syslog. I'm puzzled, what's wrong with my partition? Thanks in advance greg debian 5.0.10 LVM 2.02.39

  Read the article

• Different block sizes for partition and underlying logical disk on HP Raid Controller (Linux)

  - by Wawrzek

  Following links collected in this thread I started to check blockdev and found the following output indicating different sizes for partition c0d9p1 and the underlying device (c0d9): [root@machine ~]# blockdev --report /dev/cciss/c0d9 RO RA SSZ BSZ StartSec Size Device rw 256 512 4096 0 3906963632 /dev/cciss/c0d9 [root@machine ~]# blockdev --report /dev/cciss/c0d9p1 RO RA SSZ BSZ StartSec Size Device rw 256 512 2048 1 3906959039 /dev/cciss/c0d9p1 We have a lot of small files, so yes the block size is smaller than normal. The device is a logical driver on an HP P410 raid controller, simple disk without any raid - RAID 0 on one disk to be precise. (Please note that above configuration is a feature not a bug). Therefore, I have the following questions. Can the above discrepancy in the block size affect disk performance? Can I control the block size using hpacucli?

  Read the article

• needing storage integrity (write/read) test - for BASH

  - by Mr. Bash

  In need of shell scripts / bash commands to verify data integrity of local harddrives, usb-drives, etc, ... Like the famous www.heise.de/download/h2testw; or something that is at least common within repositories. (h2testw writes a specific datastring over and over onto the medium, then reads it again to verify if it was written correctly and displays write/read time/speed.) please no dd if=/dev/random of=/dev/sdx bs=1k && dd if=/dev/sdx of=/dev/null bs=1k since it won't verify if everything was written correctly. It is only a test if read/write is successful to the device. So far, I'm not too happy with badblocks -w -v /dev/sdx1 either, since it seems rather slow and I don't know what it exactly writes, and if it considers wear-leveling on flash media. There is also a program named F3 http://oss.digirati.com.br/f3/ that needs to be compiled. Designed after h2testw, the concept sounds interesting, i'd just rather have it as a ready to go bash script.

  Read the article

• Merge LVM Partition with unallocated Space

  - by David

  I have a linux hard drive with three areas: /dev/hda1 - ext3 boot partition (20 MB) /dev/hda2 - lvm2 main partition (6 GB) unpartitioned space - 12 GB I would like to merge the unpartitioned space into the lvm2 partition known as /dev/hda2. I tried using GParted, but it does not support lvm2. What commands or utilities could I use to add the unpartitioned space to hda2 without losing my existing data?

  Read the article

• Free space on Dedi' in CentOS

  - by Trance84

  It will sound stupid but i need to figure out how much disk space i have in my dedicated server, it runs CentOS6...the last command i issued was this [root@ks34900 ~]# df -h Filesystem Size Used Avail Use% Mounted on rootfs 9.7G 6.4G 2.9G 69% / /dev/root 9.7G 6.4G 2.9G 69% / none 1000M 288K 1000M 1% /dev /dev/sda2 914G 200M 868G 1% /home But again, stupid as it may sound... i cant figure out how much space i have in "/" folder (root) And is it possible that "/usr" have a different space (partition)?

  Read the article

• Restoring a Ubuntu Linux LVM drive

  - by user848106

  Scenario: I have a hard disk with a bootable sda1 partition and an Linux LVM. I seem to have corrupted the MBR? or Grub? not sure. I know it no longer boots and even with boot-repair and a Ubuntu live usb I was able to restore it. Following a "fix" with boot-repair I get "missing operating system" Can't i just reinstall grub or a new menu.lst? Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0007b68f Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 625141759 312320001 5 Extended /dev/sda5 501760 625141759 312320000 8e Linux LVM

  Read the article

• Is it possible to mount a disk image, created with dd, to a directory on a mounted external usb hdd?

  - by Keeper Hood

  I have an image of my home (/dev/sda3) partition, which I've created using the "dd" command. dd if=/dev/sda3 of=/path/to/disk.img I've deleted the home partition via gparted in order to enlarge my /dev/root partition. Then I've recreated the /dev/sda3 partition which is smaller in size then the one I've backed up to the image. I was wondering since I have a 2TB external HDD, could it be possible to mount my backed up image on the external HDD and then copy the files into the /home directory. Since the external HDD would be already in a "mounted state", I'm unsure whether this is a good idea, mounting on a mounted device. I'm running Slackware 13.37 (64bit). used ext4 on all the partitions. resized the root partition with gparted live cd. I've tried mount -t ext4 /path/to/disk.img /mng/image -o loop It gave me an fs error (wrong fs type, bad option, bad superblock on dev/loop/0) Then i did dmesg | tail which outputs: EXT4-fs (loop0) : bad geometry: block count 29009610 exceeds size of defice (1679229 blocks) I have no idea what to do, I want to restore my /home data from the image I've backed up.

  Read the article

• PLesk Error: pmm-ras error (Error code = -6): during restore.. /tmp folder to increase?

  - by eric

  I had to re-install plesk on a centos 6 system after a crash. The full backup file is 11 gb. but at the beginning of the backup reinstall I get the error Error: pmm-ras error (Error code = -6): argh ! my disk organization is like this Filesystem Size Used Avail Use% Mounted on /dev/xvda1 3.7G 801M 2.9G 22% / /dev/mapper/vg00-usr 14G 1.5G 12G 12% /usr /dev/mapper/vg00-var 155G 14G 134G 10% /var /dev/mapper/vg00-home 3.9G 136M 3.6G 4% /home none 1000M 7.5M 993M 1% /tmp I suppose I have to increase my /tmp folder to accept the backup size,but I don't know how-to. I'm on 1&1 cloud server Thanks for your help. You can imagine the emergency of this situation...

  Read the article

• EC2: How dangerous is it to turn off fsck for EBS volumes?

  - by Janine

  I have been tearing my hair out trying to figure out why my EC2 instances (made from my own custom AMIs) were taking many tries to come up properly. They would fail with the following error: fsck.ext3: No such file or directory while trying to open /dev/sdf For both of the EBS volumes I was attaching during startup. Finally, I figured out the problem. I had put this in /etc/fstab: /dev/sdf /export ext3 defaults 1 2 /dev/sdi /export2 ext3 defaults 1 2 The 2 tells the system to fsck the drives on the way up. Changing this to /dev/sdf /export ext3 defaults 1 0 /dev/sdi /export2 ext3 defaults 1 0 Avoids the problem completely, but now the volumes are never going to be fsck'd. How much does this matter? Once the instance goes into production it's going to be running pretty much 24/7, so not many fscks would be happening anyway, but still... this just feels like a bad idea. I have not been able to find anyone else even reporting this problem (there are people with the same error message, but different causes). It seems unbelievable that I could be the only person to ever make this mistake, but perhaps I'm just talented that way. :) If there is another solution to the problem I would love to hear it; I have not been able to find one.

  Read the article

• Under kvm, Vista guest OS install halts on black screen

  - by Isaac Sutherland

  I am using kvm on my ubuntu-server-10.04 amd64 dual core PC. I am trying to install a Windows Vista guest OS. The installation proceeds properly until the system reboot halfway into the installation process, at which point it stops on a black screen and CPU usage goes to near zero. I created the vm with virt-install as follows: virt-install -n vista --connect qemu:///system -r 1024 -vcpus 2 \ --os-type windows --os-variant vista \ --virt-type kvm --accelerate \ -c /dev/sr0 \ --disk path=/dev/main/vista-hd \ --network bridge=br0 \ --vnc --noautoconsole Where /dev/sr0 is the physical drive with the vista installation DVD, and /dev/main/vista-hd is a 20-GB lvm logical volume I created. A number of people seem to have had success installing vista under KVM, but I haven't been able to determine what is causing my problem. Ideas anyone?

  Read the article

• RAID 50 24Port Fast Writes Slow Reads - Ubuntu

  - by James

  What is going on here?! I am baffled. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/dev/zero of=/Volumes/MercuryInternal/test/test.fs bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 57.0948 s, 735 MB/s serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/Volumes/MercuryInternal/test/test.fs of=/dev/null bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 116.189 s, 361 MB/s OF NOTE: My RAID50 is 3 sets of 8 disks. - This might not be the best config for SPEED. OS: Ubuntu 12.04.1 x64 Hardware Raid: RocketRaid 2782 - 24 Port Controller HardDriveType: Seagate Barracuda ES.2 1TB Drivers: v1.1 Open Source Linux Drivers. So 24 x 1TB drives, partitioned using parted. Filesystem is ext4. I/O scheduler WAS noop but have changed it to deadline with no seemingly performance benefit/cost. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo gdisk -l /dev/sdb GPT fdisk (gdisk) version 0.8.1 Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Disk /dev/sdb: 41020686336 sectors, 19.1 TiB Logical sector size: 512 bytes Disk identifier (GUID): 95045EC6-6EAF-4072-9969-AC46A32E38C8 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 41020686302 Partitions will be aligned on 2048-sector boundaries Total free space is 5062589 sectors (2.4 GiB) Number Start (sector) End (sector) Size Code Name 1 2048 41015625727 19.1 TiB 0700 primary To me this should be working fine. I can't think of anything that would be causing this other then fundamental driver errors? I can't seem to get much/if any higher then the 361MB a second, is this hitting the "SATA2" link speed, which it shouldn't given it is a PCIe2.0 card. Or maybe some cacheing quirk - I do have Write Back enabled. Does anyone have any suggestions? Tests for me to perform? Or if you require more information, I am happy to provide it! This is a video fileserver for editing machines, so we have a preference for FAST reads over writes. I was just expected more from RAID 50 and 24 drives together... EDIT: (hdparm results) serveradmin@FILESERVER:/Volumes/MercuryInternal$ sudo hdparm -Tt /dev/sdb /dev/sdb: Timing cached reads: 17458 MB in 2.00 seconds = 8735.50 MB/sec Timing buffered disk reads: 884 MB in 3.00 seconds = 294.32 MB/sec EDIT2: (config details) Also, I am using a RAID block size of 256K. I was told a larger block size is better for larger (in my case large video) files. EDIT3: (Bonnie++ Results. Would love some guidance with this!)

  Read the article

• Mounting an attached ebs volume in EC2

  - by David

  I've created an EC2 instance, created an EBS volume, attached it to the running instance, and successfully ssh'ed into my instance. The drive is attached as /dev/sdf Next, I tried mounting the drive by running: mkdir /testName mount -t ext3 /dev/sdf /testName But then I get the error message: mount: wrong fs type, bad option, bad superblock on /dev/sdf, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so What am I doing wrong? Thanks.

  Read the article

• filesystem mounting problem

  - by user306988

  Hello, A DAS box is attached to my linux box using LSI SCSI HBA. Volume is properly detected on the linux box and filesystem is created using mkfs.ext2 /dev/sdc #No partition table I can not mount the volume using mount/dev/sdc /mnt/temp -t ext3 But I can mount it using mount /dev/sdc /mnt/temp -t ext3 -o loop Can anybody please tell me what "-o loop" option does internally? Has anybody faced this option before? Thanks in advance, prashant

  Read the article

• Nginx Not Passing URL Parameters

  - by jmccartie

  Messing around with Nginx ... for some reason, it looks like none of my URL parameters are being passed. My homepage loads fine, but a URL like "http://mysite.com/more.php?id=101" throws errors, saying that the ID is an undefined index. I'm assuming this is something basic I'm missing in a conf file. Some info: conf.d/virtual.conf server { listen 80; server_name dev.mysite.com; index index.php; root /var/www/dev.mysite.com_html; location / { root /var/www/dev.mysite.com_html; } location ~ \.php(.*)$ { fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME /var/www/wap/dev.mysite.com_html/$fastcgi_script_n ame; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } } Error log: 2009/06/22 11:44:21 [notice] 16319#0: start worker process 16322 2009/06/22 11:44:28 [error] 16320#0: *1 FastCGI sent in stderr: "PHP Notice: Undefined index: id in /var/www/dev.mysite.com_html/more.php on line 10 Thanks in advance.

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >