Search Results

Search found 11478 results on 460 pages for 'disk partition'.

Page 66/460 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

  • How to remove NTFS system files from a previous Vista installation

    - by Boldewyn
    I'm trying to shrink my system partition under Win Vista. It's all fine, except that in front of the last 300MB of the volume sits a single file, that cannot be moved by defrag or other means from its position. It's called C:\$Extend\$UsnJrnl:$J, and my assumtion is, that it is left from a previous installation of Vista, when I re-set up the system. Now, googling for this kind of files brings interesting results, but no solution to my problem: Files left on the disk can become ownerless in a new setup of Windows and inaccessible (even for administrators). To be able to access them again, I found the tip to use takeown to re-assign them to the Admin group (or anyone else). Works like a charm for normal files, but not for the C:\$Extend stuff. The C:\$Extend folder is a system folder of the NTFS file system, where the journal is stored (especially in a file called $UsnJrnl:$Data, whose name is surprisingly close to mine). You can delete the journal with fsutil usn /delete C:, however, this doesn't work from within the booted system (as I found out trying). Also, I'm not quite sure of the side effects. You can't move the NTFS own files with standard defrag tools. The same holds, by the way, for not accessible files. Every bit of knowledge out there is targeted to either not accessible files or the $Extend NTFS stuff, but noone addresses my problem involving both, an inaccessible system file. Question: How can I remove this file, or at least how can I move it on the disk?

    Read the article

  • Master File Table Corrupt, any way to save data?

    - by domen
    hi. I've used search, but none of the results match my problem so I didn't have to ask separate question. I've Installed Windows 7 RTM recently and since then partitions located on one of my HDDs have gone "crazy". They used to "freeze" and didn't open in explorer for some time (minute or two, usually), sometimes all partitions of the drive wouldn't show until reboot and finally, one of those partitions started showing "disk structure is corrupted and unreadable" warning, it appeared in Disk Management window as RAW and chkdsk showed "mft corrupt". There were no important data on the partition and I didn't have enough time to analyze the problem at the moment, so I just reformatted it and ran antivirus scan on system. After that problem settled for some time, but yesterday the problematic HDD vanished again from the system. After reboot chkdsk identified mft of four partitions corrupt and now they are all in same conditions as the above mentioned one. But the difference is that the files stored in them are extremely important. and just for info: I upgraded from Win7 build 7077, but had some performance issues, so I reformatted system drive and installed fresh Win7 RTM on it. I've downloaded TestDisk and it shows all the partitions marked as NTFS (not RAW) and my knowledge of the program wasn't sufficient to obtain any other info from it :-) and the images that could help describe the problem (sorry, I'm not allowed to post images and more than one hyperlink): http:// img22.imageshack.us/img22/5909/chkdskz.jpg http:// img198.imageshack.us/img198/5576/computeray.jpg I'm interested, is there a way to let me restore the MFT or just access files so I can backup them before reformatting the drive. Thanks for your time. :) P.S. my reformatted drive is showing no problems, could there be a problem with windows 7 itself? I googled, but with no results.

    Read the article

  • grub2 error : out of disk

    - by Nostradamnit
    Hi everyone, I recently install ArchBang on a machine with Ubuntu and XP. I ran update-grub from Ubuntu and it found the new install and created an entry. However, when I try to boot it, I get: error: out of disk error: you need to load kernel first I've tried several things, including adding a new entry in 40_custom, but nothing changes. Here are the entries I have: default found by update-grub ### BEGIN /etc/grub.d/30_os-prober ### menuentry "ArchBang Linux (on /dev/sda4)" { insmod part_msdos insmod ext2 set root='(hd0,msdos4)' search --no-floppy --fs-uuid --set 75f96b44-3a8f-4727-9959-d669b9244f2a linux /boot/vmlinuz26 root=/dev/sda4 rootfstype=ext4 ro xorg=vesa quiet nomodeset swapon initrd /boot/kernel26.img } menuentry "ArchBang Linux Fallback (on /dev/sda4)" { insmod part_msdos insmod ext2 set root='(hd0,msdos4)' search --no-floppy --fs-uuid --set 75f96b44-3a8f-4727-9959-d669b9244f2a linux /boot/vmlinuz26 root=/dev/sda4 rootfstype=ext4 ro xorg=vesa quiet nomodeset swapon initrd /boot/kernel26-fallback.img } ### END /etc/grub.d/30_os-prober ### custom entry in 40_custom based on various ideas found on the internets menuentry "ArchBang Linux (on /dev/sda4)" { insmod part_msdos insmod ext2 set root='(hd0,msdos4)' search --no-floppy --fs-uuid --set 75f96b44-3a8f-4727-9959-d669b9244f2a linux /boot/vmlinuz26 root=/dev/disk/by-uuid/75f96b44-3a8f-4727-9959-d669b9244f2a rootfstype=ext4 ro xorg=vesa quiet nomodeset swapon initrd /boot/kernel26.img } I think the problem has something to do with the sda4 not being mounted at boot-time... Thanks in advance for you help, Sam

    Read the article

  • Recovery disk Windows 8 HP Pavilion g6

    - by fpghost
    I recently purchased a HP Pavilion g6 laptop running Windows 8. I want to either obtain the Windows 8 ISO or make some kind of recovery disk that would allow me to restore the system if things go wrong. The HP Pavilion comes with the 'HP Recovery Manager' which I thought may do the job, but on running it and putting in a DVD-R as requested it seems to just hang for a number of hours without doing a thing (the disk sounds like it's spinning for a few minutes but then goes silent). I then tried 'recdisc.exe' but I get the error System Repair could not be created The device reported unexpected or invalid data for a command. (0xC0AA02FF) Next I obtained my Windows 8 product key using the software ProduKey thinking this would allow me to go to the Microsoft website and download the Windows 8 ISO, but as far as I can tell all that is available is the upgrade which can be used if one is running something like Windows 7. Can anyone advise? EDIT: after a reboot recdisc.exe did work; I think the problem was due to some Windows updates needing a reboot, but never the less I would like a full Windows 8 ISO if possible.

    Read the article

  • p410i Mirror failed couldnt find same disk

    - by Heishiro Mitsurugi
    I have an HP server with an P410i RAID Card installed. I had two SATA Drives connected (250GB each). The RAID was configured as a Mirror. A few days ago the drive one (1) failed, and i had to remove it. Tried to find the same part number here in Venezuela, but i couldn't. So, i bought a 500GB SATA Drive, and connected it to the same bay where the 250GB failed drive was. When the server booted, it asked me if i wanted to rebuild the data. I selected the option for that, and Windows Server restarted properly. When i got into the ACU (Array Configuration Utility) it told me that it was rebuilding the data. Today the warning went away, and according to the ACU everything is just fine. My question is... What i did was right? Can i create a mirror from a 250GB disk in a 500GB disk using the p410i? I have done that before, but only using software RAID in Windows, and it just uses the space it needs. As a matter of fact, when did that using Windows i was able to use the remaining space in the bigger drive, but in the p410i i can't use it. Should i be worried? Thanks a lot in advance for any pointers or info that you could give on this. Heishiro

    Read the article

  • Performance of external USB disk with ESXi5

    - by PeterMmm
    I have a new HP DL120 G7 server with ESXi5. One VM is a Win2003 instalation and I have an external USB2.0 drive attached by USB Controller and USB Device. I copy a 4GB file from external USB to server disk. In the VM that takes up to 10 minutes. On a native Win2003 that takes aprox. 3 minutes. I have no explaination for that diference: In any case the bottleneck is the USB connection, much slower than the disks (SAS, RAID1). If the USB connection on the VM would be USB1.1 and not USB2.0 it would take much more time. (The disk performance between server partitions on the VM is correct. - see update) Could be that my native box is extremely fast and the VM is the normal case. ??? Update I try with passtrough and a first run copy the same data in aprox. 7 minutes. Still 2 times slower than the native connection. I also did another messure and the copy between partitions on the same VM takes 3 minutes.

    Read the article

  • mdadm lvm and ext4 slowness - How can I speed it up?

    - by beatbreaker
    I can't figure out why I'm getting such terrible times out of my mdadm and in particular the lvm partitions in it. I made the raid: mdadm --create --verbose /dev/md0 --level=5 --chunk=1024 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sda1[0] sdd1[3] sdc1[2] sdb1[1] 2930279424 blocks level 5, 1024k chunk, algorithm 2 [4/4] [UUUU] I then created the physical volume, volume group, and logical volumes, I then formatted the logical volumes to ext4 using the following commands I got from here: http://busybox.net/~aldot/mkfs_stride.html mkfs.ext3 -b 4096 -E stride=256,stripe-width=768 /dev/datavg/blah Now I'm confused, I had these lvs running real quick before in mdadm but now that I've 'optimized' everything it's slower, eg, before: /dev/datavg/lv_audio: Timing buffered disk reads: 598 MB in 3.01 seconds = 198.85 MB/sec but now after: /dev/datavg/audio: Timing buffered disk reads: 198 MB in 3.00 seconds = 65.96 MB/sec That's pitiful! What's happened here? Did I not follow the instructions correctly? Can i reshape the ext4 partitons to default back to what they were? (I used defaults before and they were fine!)

    Read the article

  • Restoring Mac-bootcamp-windows-partition image to Windows machine

    - by jpwagner
    Hi, I'm running Windows XP sp3 on my mac using bootcamp. Objective: I'd like to move this partition to a windows machine. This is what I tried: 1. create image using winclone 2. restore drive to disk partition on windows machine using paragon 3. reboot from new partition Results: it attempts to boot in XP (windows flag and progress bar load screen) but then gives me the old BSOD. safe mode just hangs while loading. (I then uninstalled KB977165 on a hunch, but that did nothing to help the issue.) Any ideas, advice, etc would be greatly appreciated. Thanks!

    Read the article

  • Mounting ubuntu's root.disk in Windows 7

    - by gAMBOOKa
    I've got Ubuntu 9.10 installed in an NTFS partition. After an update, I started getting kernel panics, so I need to reinstall it. But before I do that, I need to retrieve and backup my home directory. I believe Ubuntu's file system is packaged in the root.disk image. So how do I mount it in Windows?

    Read the article

  • Ubuntu 10.04 Installation

    - by Sarang
    I do have XP on my PC. I want to shift to Ubuntu 10.04. I want to format whole PC & want to keep only Ubuntu. Should I have to keep partition for it like we do in previous version of Ubuntu. Doesn't it waste my space ?

    Read the article

  • Resize partition of Windows 7 running on VirtualBox with dynamically allocated storage

    - by Nicolas Raoul
    I run Windows 7 inside VirtualBox. I resized the disk of Windows 7 from 25 GB to 50 GB: VBoxManage modifyhd Windows\ 7\ Pro.vdi --resize 50000 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% PROBLEM: I can' grow the partition, neither with Windows 7 itself nor with GParted: It looks like VirtualBox does not tell the client OS about the new size. What additional step is necessary?

    Read the article

  • Why create many partitions?

    - by ryeguy
    I have noticed that when installing Ubuntu some people create multiple partitions for directories. Like one for root, one for home, one for boot. What is the advantage to doing this over installing them all on one partition, assuming there is only one hard drive?

    Read the article

  • 2nd Bootable partition P2V conversion

    - by Vendoran
    I have a dual boot machine (Win7 RC and Win2008) and want to migrate one of the partitions (Win2008) into a Virtual Hard Drive and the be able to use it in VPC or Virtual Server (not Hyper-V). The ways I've seen via Linked Virtual Disks or WinImage take the entire physical drive instead of just the partition. Any ideas? Thanks in Advance, --Aaron

    Read the article

  • Partition 500gb of database stored in SQL Server

    - by Devendra
    Hello I have 500GB of database stored in SQL Server. Because it has too big a database, it takes time to update and insert data. Now the case is that I want to partition the data. So which partitioning techniques should I use? Or is there any other technique which will improve my performance?

    Read the article

  • Extend partition windows powershell

    - by user128364
    I want to create a Windows Powershell script to extend my partition through WMI (remotely), IP Address of my host id 10.10.10.10 $pass = convertto-securestring "abc123#" -asplaintext -force $mycred = new-object -typename System.Management.Automation.PSCredential -argumentlist "10.10.10.10\Administrator",$pass Invoke-Command -ComputerName 10.10.10.10 -Credential $myCred -ScriptBlock {"rescan","select volume 2","extend" | diskpart} Do we have any method with use of Invoke-Wmimethod

    Read the article

  • Partition Label Problem after DD Image

    - by bobby
    After imaging a 100GB hard drive into an image file with dd, I dd'd the image to a larger hdd After boot get mkrootdev: label / not found I have gone in with finnix and relabeled the partition to the same label with e2label and still have problems. Has anyone resolved this before?

    Read the article

  • Installing Windows 7 on a netbook using SanDisk USB Cruzer

    - by alexus
    I have this weird problem with my SanDisk USB Cruzer maybe someone can help me... I removed U3 software I used diskpart.exe to "activate" my partition yet when I restart my computer and select to boot off of USB it won't boot, my computer freezes and nothing is happening after that. any ideas what am I doing wrong?

    Read the article

  • Windows External Harddisk drive letter after cloning boot partition to it

    - by gladiator2345
    I cloned my windows 7 installation on c: to external hard drive. I applied usb patch using pwboot and i could successfully boot into windows. But My problem is even though i am booting in to external hd the file reference and system path is pointing to c: on my internal hard disk. If i remove internal hd and boot it will get stuck at login screen. Is there any way i can force drive letter c: to my boot partition on external hd while booting from it.

    Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >