Search Results

Search found 68011 results on 2721 pages for 'unit of work'.

Page 66/2721 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• Atheros AR9485 wireless card doesn't work in an ASUS K53E

  - by John

  I just installed Ubuntu 11.10 32-bit version in dual boot mode on an ASUS K53. Every thing seems to work fine except for the wireless. The wireless works on Windows 7. Ubuntu finds the wireless card, but it does not appear to be turned on. The only physical means of turning on the card is the FN-F2 key combo. That works on Windows, but not in Ubuntu. I've looked in the forums for a solution and I'm not quite sure what to do. I've gathered the following information: jdwbmc@Spatha:~$ cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" Linux Spatha 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:50:42 UTC 2011 i686 i686 i386 GNU/Linux jdwbmc@Spatha:~$ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:1186] Kernel driver in use: ath9k -- 04:00.0 Ethernet controller [0200]: Atheros Communications AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) Subsystem: ASUSTeK Computer Inc. Device [1043:1851] Kernel driver in use: atl1c jdwbmc@Spatha:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 058f:a014 Alcor Micro Corp. jdwbmc@Spatha:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff jdwbmc@Spatha:~$ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no jdwbmc@Spatha:~$ lsmod Module Size Used by parport_pc 32114 0 ppdev 12849 0 snd_hda_codec_hdmi 31426 1 bnep 17923 2 rfcomm 38408 0 bluetooth 148839 10 bnep,rfcomm snd_hda_codec_realtek 254125 1 binfmt_misc 17292 1 joydev 17393 0 asus_nb_wmi 12469 0 asus_wmi 19333 1 asus_nb_wmi sparse_keymap 13658 1 asus_wmi uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 24262 2 snd_hda_codec 91754 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80468 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 wmi 18744 1 asus_wmi snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event arc4 12473 2 i915 505108 3 snd_timer 28932 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq ath9k 112711 0 psmouse 73673 0 serio_raw 12990 0 mac80211 272785 1 ath9k drm_kms_helper 32889 1 i915 ath9k_common 13599 1 ath9k drm 192226 4 i915,drm_kms_helper ath9k_hw 293893 2 ath9k,ath9k_common ath 19387 2 ath9k,ath9k_hw cfg80211 172392 3 ath9k,mac80211,ath snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,s nd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm mei 36466 0 i2c_algo_bit 13199 1 i915 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 3 libahci 25727 1 ahci atl1c 36638 0 xhci_hcd 72915 0 jdwbmc@Spatha:/var/lib/NetworkManager$ cat NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true jdwbmc@Spatha:~$ lspci -nn | grep 0280 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Any help would be appreciated. Thanks.

  Read the article

• wifi hardware switch doesn't work on a Dell 1018

  - by user42566

  I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

  Read the article

• JDeveloper 11.1.2 : Command Link in Table Column Work Around

  - by Frank Nimphius

  Just figured that in Oracle JDeveloper 11.1.2, clicking on a command link in a table does not mark the table row as selected as it is the behavior in previous releases of Oracle JDeveloper. For the time being, the following work around can be used to achieve the "old" behavior: To mark the table row as selected, you need to build and queue the table selection event in the code executed by the command link action listener. To queue a selection event, you need to know about the rowKey of the row that the command link that you clicked on is located in. To get to this information, you add an f:attribute tag to the command link as shown below <af:column sortProperty="#{bindings.DepartmentsView1.hints.DepartmentId.name}" sortable="false"    headerText="#{bindings.DepartmentsView1.hints.DepartmentId.label}" id="c1">   <af:commandLink text="#{row.DepartmentId}" id="cl1" partialSubmit="true"       actionListener="#{BrowseBean.onCommandItemSelected}">     <f:attribute name="rowKey" value="#{row.rowKey}"/>   </af:commandLink>   ... </af:column> The f:attribute tag references #{row.rowKey} wich in ADF translates to JUCtrlHierNodeBinding.getRowKey(). This information can be used in the command link action listener to compose the RowKeySet you need to queue the selected row. For simplicitly reasons, I created a table "binding" reference to the managed bean that executes the command link action. The managed bean code that is referenced from the af:commandLink actionListener property is shown next: public void onCommandItemSelected(ActionEvent actionEvent) {   //get access to the clicked command link   RichCommandLink comp = (RichCommandLink)actionEvent.getComponent();   //read the added f:attribute value   Key rowKey = (Key) comp.getAttributes().get("rowKey");     //get the current selected RowKeySet from the table   RowKeySet oldSelection = table.getSelectedRowKeys();   //build an empty RowKeySet for the new selection   RowKeySetImpl newSelection = new RowKeySetImpl();     //RowKeySets contain List objects with key objects in them   ArrayList list = new ArrayList();   list.add(rowKey);   newSelection.add(list);     //create the selectionEvent and queue it   SelectionEvent selectionEvent = new SelectionEvent(oldSelection, newSelection, table);   selectionEvent.queue();     //refresh the table   AdfFacesContext.getCurrentInstance().addPartialTarget(table); }

  Read the article

• Drawing texture does not work anymore with a small amount of triangles

  - by Paul

  When i draw lines, the vertices are well connected. But when i draw the texture inside the triangles, it only works with i<4 in the for loop, otherwise with i<5 for example, there is a EXC_BAD_ACCESS message, at @synthesize textureImage = _textureImage. I don't understand why. (The generatePolygons method seems to work fine as i tried to draw lines with many vertices as in the second image below. And textureImage remains the same for i<4 or i<5 : it's a 512px square image). Here are the images : What i want to achieve is to put the red points and connect them to the y-axis (the green points) and color the area (the green triangles) : If i only draw lines, it works fine : Then with a texture color, it works for i<4 in the loop (the red points in my first image, plus the fifth one to connect the last y) : But then, if i set i<5, the debug tool says EXC_BAD_ACCESS at the synthesize of _textureImage. Here is my code : I set a texture color in HelloWordLayer.mm with : CCSprite *textureImage = [self spriteWithColor:color3 textureSize:512]; _terrain.textureImage = textureImage; Then in the class Terrain, i create the vertices and put the texture in the draw method : @implementation Terrain @synthesize textureImage = _textureImage; //EXC_BAD_ACCESS for i<5 - (void)generatePath2{ CGSize winSize = [CCDirector sharedDirector].winSize; float x = 40; float y = 0; for(int i = 0; i < kMaxKeyPoints+1; ++i) { _hillKeyPoints[i] = CGPointMake(x, y); x = 150 + (random() % (int) 30); y += 30; } } -(void)generatePolygons{ _nPolyVertices = 0; float x1 = 0; float y1 = 0; int keyPoints = 0; for (int i=0; i<4; i++){ /* HERE : 4 = OK / 5 = crash */ //V0: at (0,0) _polyVertices[_nPolyVertices] = CGPointMake(x1, y1); _polyTexCoords[_nPolyVertices++] = CGPointMake(x1, y1); //V1: to the first "point" _polyVertices[_nPolyVertices] = CGPointMake(_hillKeyPoints[keyPoints].x, _hillKeyPoints[keyPoints].y); _polyTexCoords[_nPolyVertices++] = CGPointMake(_hillKeyPoints[keyPoints].x, _hillKeyPoints[keyPoints].y); keyPoints++; //from point at index 0 to 1 //V2, same y as point n°2: _polyVertices[_nPolyVertices] = CGPointMake(0, _hillKeyPoints[keyPoints].y); _polyTexCoords[_nPolyVertices++] = CGPointMake(0, _hillKeyPoints[keyPoints].y); //V1 again _polyVertices[_nPolyVertices] = _polyVertices[_nPolyVertices-2]; _polyTexCoords[_nPolyVertices++] = _polyVertices[_nPolyVertices-2]; //V2 again _polyVertices[_nPolyVertices] = _polyVertices[_nPolyVertices-2]; _polyTexCoords[_nPolyVertices++] = _polyVertices[_nPolyVertices-2]; //V3 = same x,y as point at index 1 _polyVertices[_nPolyVertices] = CGPointMake(_hillKeyPoints[keyPoints].x, _hillKeyPoints[keyPoints].y); _polyTexCoords[_nPolyVertices] = CGPointMake(_hillKeyPoints[keyPoints].x, _hillKeyPoints[keyPoints].y); y1 = _polyVertices[_nPolyVertices].y; _nPolyVertices++; } } - (id)init { if ((self = [super init])) { [self generatePath2]; [self generatePolygons]; } return self; } - (void) draw { //glDisable(GL_TEXTURE_2D); glDisableClientState(GL_COLOR_ARRAY); glDisableClientState(GL_TEXTURE_COORD_ARRAY); glBindTexture(GL_TEXTURE_2D, _textureImage.texture.name); glColor4f(1, 1, 1, 1); glVertexPointer(2, GL_FLOAT, 0, _polyVertices); glTexCoordPointer(2, GL_FLOAT, 0, _polyTexCoords); glDrawArrays(GL_TRIANGLE_STRIP, 0, (GLsizei)_nPolyVertices); glColor4f(1, 1, 1, 1); for(int i = 1; i < 40; ++i) { ccDrawLine(_polyVertices[i-1], _polyVertices[i]); } // restore default GL states glEnable(GL_TEXTURE_2D); glEnableClientState(GL_COLOR_ARRAY); glEnableClientState(GL_TEXTURE_COORD_ARRAY); } Do you see anything wrong in this code? Thanks for your help

  Read the article

• How does gluLookAt work?

  - by Chan

  From my understanding, gluLookAt( eye_x, eye_y, eye_z, center_x, center_y, center_z, up_x, up_y, up_z ); is equivalent to: glRotatef(B, 0.0, 0.0, 1.0); glRotatef(A, wx, wy, wz); glTranslatef(-eye_x, -eye_y, -eye_z); But when I print out the ModelView matrix, the call to glTranslatef() doesn't seem to work properly. Here is the code snippet: #include <stdlib.h> #include <stdio.h> #include <GL/glut.h> #include <iomanip> #include <iostream> #include <string> using namespace std; static const int Rx = 0; static const int Ry = 1; static const int Rz = 2; static const int Ux = 4; static const int Uy = 5; static const int Uz = 6; static const int Ax = 8; static const int Ay = 9; static const int Az = 10; static const int Tx = 12; static const int Ty = 13; static const int Tz = 14; void init() { glClearColor(0.0, 0.0, 0.0, 0.0); glEnable(GL_DEPTH_TEST); glShadeModel(GL_SMOOTH); glEnable(GL_LIGHTING); glEnable(GL_LIGHT0); GLfloat lmodel_ambient[] = { 0.8, 0.0, 0.0, 0.0 }; glLightModelfv(GL_LIGHT_MODEL_AMBIENT, lmodel_ambient); } void displayModelviewMatrix(float MV[16]) { int SPACING = 12; cout << left; cout << "\tMODELVIEW MATRIX\n"; cout << "--------------------------------------------------" << endl; cout << setw(SPACING) << "R" << setw(SPACING) << "U" << setw(SPACING) << "A" << setw(SPACING) << "T" << endl; cout << "--------------------------------------------------" << endl; cout << setw(SPACING) << MV[Rx] << setw(SPACING) << MV[Ux] << setw(SPACING) << MV[Ax] << setw(SPACING) << MV[Tx] << endl; cout << setw(SPACING) << MV[Ry] << setw(SPACING) << MV[Uy] << setw(SPACING) << MV[Ay] << setw(SPACING) << MV[Ty] << endl; cout << setw(SPACING) << MV[Rz] << setw(SPACING) << MV[Uz] << setw(SPACING) << MV[Az] << setw(SPACING) << MV[Tz] << endl; cout << setw(SPACING) << MV[3] << setw(SPACING) << MV[7] << setw(SPACING) << MV[11] << setw(SPACING) << MV[15] << endl; cout << "--------------------------------------------------" << endl; cout << endl; } void reshape(int w, int h) { float ratio = static_cast<float>(w)/h; glViewport(0, 0, w, h); glMatrixMode(GL_PROJECTION); glLoadIdentity(); gluPerspective(45.0, ratio, 1.0, 425.0); } void draw() { float m[16]; glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); glMatrixMode(GL_MODELVIEW); glLoadIdentity(); glGetFloatv(GL_MODELVIEW_MATRIX, m); gluLookAt( 300.0f, 0.0f, 0.0f, 0.0f, 0.0f, 0.0f, 0.0f, 1.0f, 0.0f ); glColor3f(1.0, 0.0, 0.0); glutSolidCube(100.0); glGetFloatv(GL_MODELVIEW_MATRIX, m); displayModelviewMatrix(m); glutSwapBuffers(); } int main(int argc, char** argv) { glutInit(&argc, argv); glutInitDisplayMode(GLUT_DOUBLE | GLUT_RGB | GLUT_DEPTH); glutInitWindowSize(400, 400); glutInitWindowPosition(100, 100); glutCreateWindow("Demo"); glutReshapeFunc(reshape); glutDisplayFunc(draw); init(); glutMainLoop(); return 0; } No matter what value I use for the eye vector: 300, 0, 0 or 0, 300, 0 or 0, 0, 300 the translation vector is the same, which doesn't make any sense because the order of code is in backward order so glTranslatef should run first, then the 2 rotations. Plus, the rotation matrix, is completely independent of the translation column (in the ModelView matrix), then what would cause this weird behavior? Here is the output with the eye vector is (0.0f, 300.0f, 0.0f) MODELVIEW MATRIX -------------------------------------------------- R U A T -------------------------------------------------- 0 0 0 0 0 0 0 0 0 1 0 -300 0 0 0 1 -------------------------------------------------- I would expect the T column to be (0, -300, 0)! So could anyone help me explain this? The implementation of gluLookAt from http://www.mesa3d.org void GLAPIENTRY gluLookAt(GLdouble eyex, GLdouble eyey, GLdouble eyez, GLdouble centerx, GLdouble centery, GLdouble centerz, GLdouble upx, GLdouble upy, GLdouble upz) { float forward[3], side[3], up[3]; GLfloat m[4][4]; forward[0] = centerx - eyex; forward[1] = centery - eyey; forward[2] = centerz - eyez; up[0] = upx; up[1] = upy; up[2] = upz; normalize(forward); /* Side = forward x up */ cross(forward, up, side); normalize(side); /* Recompute up as: up = side x forward */ cross(side, forward, up); __gluMakeIdentityf(&m[0][0]); m[0][0] = side[0]; m[1][0] = side[1]; m[2][0] = side[2]; m[0][1] = up[0]; m[1][1] = up[1]; m[2][1] = up[2]; m[0][2] = -forward[0]; m[1][2] = -forward[1]; m[2][2] = -forward[2]; glMultMatrixf(&m[0][0]); glTranslated(-eyex, -eyey, -eyez); }

  Read the article

• Can't make AWUS036H work in Ubuntu 12.10

  - by sfrj

  I am using 64 bit Ubuntu 12.10. This is my kernel version: Linux 3.5.0-19-generic #30-Ubuntu SMP Tue Nov 13 17:48:01 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux My wireless card is an AWUSU36H The first thing I do to install the driver is copy the driver from the CD to the Downloads folder. cd /media/me/AWUS036H/Drivers/RTL8187L/Unix (Linux)/Linux driver for kernel 2.6.X$ cp rtl8187_linux_26.1025.0328.2007.tar.gz ~/Downloads/ Then I extract the tar tar xvfz rtl8187_linux_26.1025.0328.2007.tar.gz I navigate into the extracted folder, and I try to follow the instructions in the Readme.txt cd rtl8187_linux_26.1025.0328.2007 This are the contents of the folder: drv.tar.gz makedrv stack.tar.gz wlan0rmv ieee80211 ReadMe.txt wlan0dhcp wlan0up ifcfg-wlan0 rtl8187 wlan0down wpa_supplicant-0.4.9 This is what the Readme.txt says: Release Date: 2006-02-09, ver 1.2^M RTL8187 Linux driver version 1.2^M ^M --This driver supports RealTek RTL8187 Wireless LAN driver for ^M Fedora Core 2/3/4/5, Debian 3.1, Mandrake 10.2/Mandriva 2006, ^M SUSE 9.3/10.1/10.2, Gentoo 3.1, etc.^M - Support Client mode for either infrastructure or adhoc mode^M - Support WEP and WPAPSK connection^M ^M < Component >^M The driver is composed of several parts:^M 1. Module source code^M stack.tar.gz^M drv.tar.gz^M ^M 2. Script ot build the modules^M makedrv^M ^M 3. Script to load/unload modules^M wlan0up^M wlan0down ^M ^M 4. Script and configuration for DHCP^M "ReadMe.txt" [readonly] 140 lines, 4590 characters So what I do know is extract both of the compressed files: sudo tar xvfz drv.tar.gz sudo tar xvfz stack.tar.gz This 2 commands will add some data to the folders ieee80211 and rtl8187 At this point I get lost, and I don't know what to do. If I go in each of this 2 folders and I run the sudo make command then I get errors like this one: sudo makemake -C /lib/modules/3.5.0-19-generic/build M=/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187 modules make[1]: Entering directory `/usr/src/linux-headers-3.5.0-19-generic' CC [M] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.c:64:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187.h:29:26: fatal error: linux/config.h: No such file or directory compilation terminated. make[2]: *** [/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o] Error 1 make[1]: *** [_module_/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-19-generic' make: *** [modules] Error 2 If I try to run any of the script ./makedrv that the instructions describe, then I also get an error: ~/Downloads/rtl8187_linux_26.1025.0328.2007$ sudo ./makedrv [sudo] password for me: ieee80211/ ieee80211/license ieee80211/ieee80211_crypt.c ieee80211/ieee80211_tx.c ieee80211/ieee80211_softmac.c ieee80211/ieee80211_softmac_wx.c ieee80211/ieee80211_module.c ieee80211/ieee80211_crypt_ccmp.c ieee80211/ieee80211_rx.c ieee80211/tags ieee80211/ieee80211_crypt_tkip.c ieee80211/Makefile ieee80211/readme ieee80211/.tmp_versions/ ieee80211/.tmp_versions/ieee80211-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt_wep-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt_tkip-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt_ccmp-rtl.mod ieee80211/ieee80211_crypt_wep.c ieee80211/ieee80211.h ieee80211/ieee80211_wx.c ieee80211/ieee80211_crypt.h rtl8187/ rtl8187/license rtl8187/r8180_rtl8225z2.c rtl8187/r8180_rtl8225.h rtl8187/r8187_led.c rtl8187/r8180_93cx6.h rtl8187/r8180_wx.h rtl8187/r8180_hw.h rtl8187/copying rtl8187/r8187_led.h rtl8187/r8180_pm.h rtl8187/tags rtl8187/r8187.h rtl8187/Makefile rtl8187/r8180_rtl8225.c rtl8187/readme rtl8187/install rtl8187/.tmp_versions/ rtl8187/.tmp_versions/r8187.mod rtl8187/changes rtl8187/r8180_wx.c rtl8187/r8180_pm.c rtl8187/r8187_core.c rtl8187/r8180_93cx6.c rtl8187/authors rtl8187/ieee80211.h rtl8187/ieee80211_crypt.h rm -f *.mod.c *.mod *.o .*.cmd *.ko *~ rm -rf /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/tmp make -C /lib/modules/3.5.0-19-generic/build M=/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211 modules make[1]: Entering directory `/usr/src/linux-headers-3.5.0-19-generic' CC [M] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.o In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:1019:24: error: field ‘ps_task’ has incomplete type /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_scan_wq’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:421:2: warning: passing argument 2 of ‘queue_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:371:12: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_stop_scan’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:495:3: warning: passing argument 1 of ‘cancel_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:410:20: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_associate_abort’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:915:2: warning: passing argument 2 of ‘queue_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:371:12: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_rx_frame_softmac’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:1527:3: error: implicit declaration of function ‘tasklet_schedule’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_stop_protocol_rtl’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2120:2: warning: passing argument 1 of ‘cancel_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:410:20: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_init’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2229:78: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2229:2: error: ‘INIT_WORK’ undeclared (first use in this function) /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2229:2: note: each undeclared identifier is reported only once for each function it appears in /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2230:88: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2231:94: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2232:96: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2233:82: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2234:82: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2244:2: error: implicit declaration of function ‘tasklet_init’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_free’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2255:2: warning: passing argument 1 of ‘cancel_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:410:20: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_wpa_set_encryption’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2489:3: error: implicit declaration of function ‘request_module’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2518:3: error: implicit declaration of function ‘try_module_get’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: At top level: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2663:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2663:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2663:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2664:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2664:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2664:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2665:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2665:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2665:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2666:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2666:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2666:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2667:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2667:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2667:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2668:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2668:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2668:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2669:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2669:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2669:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2670:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2670:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2670:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2671:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2671:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2671:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2672:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2672:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2672:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2673:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2673:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2673:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2674:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2674:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2674:1: warning: parameter names (without types) in function declaration [enabled by default] In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:1212:37: warning: ‘netdev_priv’ is static but used in inline function ‘ieee80211_priv’ which is not static [enabled by default] cc1: some warnings being treated as errors make[2]: *** [/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.o] Error 1 make[1]: *** [_module_/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-19-generic' make: *** [modules] Error 2 rm -f *.mod.c *.mod *.o .*.cmd *.ko *~ rm -rf /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/tmp make -C /lib/modules/3.5.0-19-generic/build M=/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187 modules make[1]: Entering directory `/usr/src/linux-headers-3.5.0-19-generic' CC [M] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.c:64:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187.h:29:26: fatal error: linux/config.h: No such file or directory compilation terminated. make[2]: *** [/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o] Error 1 make[1]: *** [_module_/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-19-generic' make: *** [modules] Error 2 Can somebody give me a hand finding out what I need to do to make my wifi card work? Update This is the output of the lsusb command lsusb Bus 003 Device 002: ID 147e:1000 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

  Read the article

• Internet doesn't work by default

  - by Adam Martinez

  After upgrading to Precise, I am required to run 'sudo dhclient eth0' in a terminal in order to get the internet to work. Everything worked perfectly fine on Oneiric, so It's really puzzling me. I'm thinking it could possibly be something with the kernel, but who knows. Output of dmesg: [ 0.247891] system 00:01: [io 0x0290-0x030f] has been reserved [ 0.247896] system 00:01: [io 0x0290-0x0297] has been reserved [ 0.247901] system 00:01: [io 0x0880-0x088f] has been reserved [ 0.247908] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.247931] pnp 00:02: [dma 4] [ 0.247935] pnp 00:02: [io 0x0000-0x000f] [ 0.247939] pnp 00:02: [io 0x0080-0x0090] [ 0.247943] pnp 00:02: [io 0x0094-0x009f] [ 0.247947] pnp 00:02: [io 0x00c0-0x00df] [ 0.248033] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.248125] pnp 00:03: [io 0x0070-0x0073] [ 0.248187] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.248205] pnp 00:04: [io 0x0061] [ 0.248260] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.248277] pnp 00:05: [io 0x00f0-0x00ff] [ 0.248292] pnp 00:05: [irq 13] [ 0.248348] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.248583] pnp 00:06: [io 0x03f0-0x03f5] [ 0.248588] pnp 00:06: [io 0x03f7] [ 0.248597] pnp 00:06: [irq 6] [ 0.248601] pnp 00:06: [dma 2] [ 0.248690] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.248998] pnp 00:07: [io 0x03f8-0x03ff] [ 0.249008] pnp 00:07: [irq 4] [ 0.249122] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.249479] pnp 00:08: [io 0x0400-0x04bf] [ 0.249584] system 00:08: [io 0x0400-0x04bf] has been reserved [ 0.249591] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.249628] pnp 00:09: [mem 0xffb80000-0xffbfffff] [ 0.249690] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) [ 0.250049] pnp 00:0a: [mem 0xe0000000-0xefffffff] [ 0.250167] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved [ 0.250173] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.250302] pnp 00:0b: [mem 0x000f0000-0x000fffff] [ 0.250307] pnp 00:0b: [mem 0x7ff00000-0x7fffffff] [ 0.250311] pnp 00:0b: [mem 0xfed00000-0xfed000ff] [ 0.250316] pnp 00:0b: [mem 0x0000046e-0x0000056d] [ 0.250320] pnp 00:0b: [mem 0x7fee0000-0x7fefffff] [ 0.250324] pnp 00:0b: [mem 0x00000000-0x0009ffff] [ 0.250328] pnp 00:0b: [mem 0x00100000-0x7fedffff] [ 0.250332] pnp 00:0b: [mem 0xfec00000-0xfec00fff] [ 0.250336] pnp 00:0b: [mem 0xfed14000-0xfed1dfff] [ 0.250341] pnp 00:0b: [mem 0xfed20000-0xfed9ffff] [ 0.250345] pnp 00:0b: [mem 0xfee00000-0xfee00fff] [ 0.250349] pnp 00:0b: [mem 0xffb00000-0xffb7ffff] [ 0.250353] pnp 00:0b: [mem 0xfff00000-0xffffffff] [ 0.250357] pnp 00:0b: [mem 0x000e0000-0x000effff] [ 0.250409] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0007ffff pref] [ 0.250419] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref] [ 0.250430] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:04:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.250524] system 00:0b: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.250530] system 00:0b: [mem 0x7ff00000-0x7fffffff] has been reserved [ 0.250536] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved [ 0.250541] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved [ 0.250547] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.250552] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved [ 0.250558] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.250563] system 00:0b: [mem 0xfed14000-0xfed1dfff] has been reserved [ 0.250568] system 00:0b: [mem 0xfed20000-0xfed9ffff] has been reserved [ 0.250574] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.250579] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved [ 0.250585] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved [ 0.250590] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved [ 0.250596] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.250614] pnp: PnP ACPI: found 12 devices [ 0.250617] ACPI: ACPI bus type pnp unregistered [ 0.250624] PnPBIOS: Disabled by ACPI PNP [ 0.288725] PCI: max bus depth: 1 pci_try_num: 2 [ 0.288786] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb07ffff pref] [ 0.288792] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.288797] pci 0000:00:01.0: bridge window [io 0xa000-0xafff] [ 0.288804] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xfbffffff] [ 0.288811] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.288820] pci 0000:00:1c.0: PCI bridge to [bus 02-02] [ 0.288825] pci 0000:00:1c.0: bridge window [io 0x9000-0x9fff] [ 0.288833] pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff] [ 0.288840] pci 0000:00:1c.0: bridge window [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.288851] pci 0000:03:00.0: BAR 6: assigned [mem 0xfde00000-0xfde0ffff pref] [ 0.288856] pci 0000:00:1c.4: PCI bridge to [bus 03-03] [ 0.288861] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff] [ 0.288869] pci 0000:00:1c.4: bridge window [mem 0xfd700000-0xfd7fffff] [ 0.288876] pci 0000:00:1c.4: bridge window [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.288887] pci 0000:04:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref] [ 0.288891] pci 0000:00:1c.5: PCI bridge to [bus 04-04] [ 0.288897] pci 0000:00:1c.5: bridge window [io 0xb000-0xbfff] [ 0.288904] pci 0000:00:1c.5: bridge window [mem 0xfdd00000-0xfddfffff] [ 0.288911] pci 0000:00:1c.5: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.288920] pci 0000:00:1e.0: PCI bridge to [bus 05-05] [ 0.288926] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff] [ 0.288933] pci 0000:00:1e.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.288940] pci 0000:00:1e.0: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.288971] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288979] pci 0000:00:01.0: setting latency timer to 64 [ 0.288991] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288998] pci 0000:00:1c.0: setting latency timer to 64 [ 0.289008] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.289014] pci 0000:00:1c.4: setting latency timer to 64 [ 0.289030] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.289037] pci 0000:00:1c.5: setting latency timer to 64 [ 0.289047] pci 0000:00:1e.0: setting latency timer to 64 [ 0.289054] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.289058] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.289063] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289067] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289072] pci_bus 0000:00: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289077] pci_bus 0000:01: resource 0 [io 0xa000-0xafff] [ 0.289081] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff] [ 0.289086] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.289092] pci_bus 0000:02: resource 0 [io 0x9000-0x9fff] [ 0.289096] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdbfffff] [ 0.289101] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.289106] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.289110] pci_bus 0000:03: resource 1 [mem 0xfd700000-0xfd7fffff] [ 0.289115] pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.289120] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff] [ 0.289124] pci_bus 0000:04: resource 1 [mem 0xfdd00000-0xfddfffff] [ 0.289129] pci_bus 0000:04: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.289134] pci_bus 0000:05: resource 0 [io 0xc000-0xcfff] [ 0.289138] pci_bus 0000:05: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.289143] pci_bus 0000:05: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.289148] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7] [ 0.289152] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff] [ 0.289157] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289161] pci_bus 0000:05: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289166] pci_bus 0000:05: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289233] NET: Registered protocol family 2 [ 0.289360] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.289754] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.290351] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.290670] TCP: Hash tables configured (established 131072 bind 65536) [ 0.290674] TCP reno registered [ 0.290680] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.290703] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.290868] NET: Registered protocol family 1 [ 0.290911] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.290932] pci 0000:00:1a.0: PCI INT A disabled [ 0.290956] pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.290975] pci 0000:00:1a.1: PCI INT B disabled [ 0.290992] pci 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.291012] pci 0000:00:1a.2: PCI INT D disabled [ 0.291031] pci 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291068] pci 0000:00:1a.7: PCI INT C disabled [ 0.291104] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291123] pci 0000:00:1d.0: PCI INT A disabled [ 0.291135] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.291155] pci 0000:00:1d.1: PCI INT B disabled [ 0.291166] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291185] pci 0000:00:1d.2: PCI INT C disabled [ 0.291198] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291219] pci 0000:00:1d.7: PCI INT A disabled [ 0.291258] pci 0000:01:00.0: Boot video device [ 0.291273] PCI: CLS 4 bytes, default 64 [ 0.291857] audit: initializing netlink socket (disabled) [ 0.291876] type=2000 audit(1336753420.284:1): initialized [ 0.337724] highmem bounce pool size: 64 pages [ 0.337734] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.349241] VFS: Disk quotas dquot_6.5.2 [ 0.349365] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.350418] fuse init (API version 7.17) [ 0.350611] msgmni has been set to 1685 [ 0.351179] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.351229] io scheduler noop registered [ 0.351233] io scheduler deadline registered [ 0.351247] io scheduler cfq registered (default) [ 0.351450] pcieport 0000:00:01.0: setting latency timer to 64 [ 0.351502] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X [ 0.351585] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.351639] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X [ 0.351728] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.351779] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 0.351875] pcieport 0000:00:1c.5: setting latency timer to 64 [ 0.351927] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X [ 0.352094] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.352143] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.352311] intel_idle: MWAIT substates: 0x22220 [ 0.352315] intel_idle: does not run on family 6 model 23 [ 0.352446] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 0.352455] ACPI: Power Button [PWRB] [ 0.352556] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 0.352562] ACPI: Power Button [PWRF] [ 0.352650] ACPI: Fan [FAN] (on) [ 0.355667] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.355673] ACPI: Thermal Zone [THRM] (26 C) [ 0.355750] ERST: Table is not found! [ 0.355753] GHES: HEST is not enabled! [ 0.355898] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.376332] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.376582] isapnp: Scanning for PnP cards... [ 0.709133] Freeing initrd memory: 13792k freed [ 0.729743] isapnp: No Plug & Play device found [ 0.816786] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.832385] Linux agpgart interface v0.103 [ 0.835605] brd: module loaded [ 0.837138] loop: module loaded [ 0.837452] ata_piix 0000:00:1f.2: version 2.13 [ 0.837473] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.837480] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.837546] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.838099] scsi0 : ata_piix [ 0.838253] scsi1 : ata_piix [ 0.839183] ata1: SATA max UDMA/133 cmd 0xf900 ctl 0xf800 bmdma 0xf500 irq 19 [ 0.839192] ata2: SATA max UDMA/133 cmd 0xf700 ctl 0xf600 bmdma 0xf508 irq 19 [ 0.839239] ata_piix 0000:00:1f.5: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.839246] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.839300] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.839708] scsi2 : ata_piix [ 0.839841] scsi3 : ata_piix [ 0.840301] ata3: SATA max UDMA/133 cmd 0xf200 ctl 0xf100 bmdma 0xee00 irq 19 [ 0.840308] ata4: SATA max UDMA/133 cmd 0xf000 ctl 0xef00 bmdma 0xee08 irq 19 [ 0.840429] pata_acpi 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.840467] pata_acpi 0000:03:00.0: setting latency timer to 64 [ 0.840488] pata_acpi 0000:03:00.0: PCI INT A disabled [ 0.841159] Fixed MDIO Bus: probed [ 0.841205] tun: Universal TUN/TAP device driver, 1.6 [ 0.841210] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.841322] PPP generic driver version 2.4.2 [ 0.841515] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.841542] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.841567] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.841573] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.841658] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.845582] ehci_hcd 0000:00:1a.7: cache line size of 4 is not supported [ 0.845610] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdfff000 [ 0.860022] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.860264] hub 1-0:1.0: USB hub found [ 0.860272] hub 1-0:1.0: 6 ports detected [ 0.860404] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.860424] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.860430] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.860512] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.864413] ehci_hcd 0000:00:1d.7: cache line size of 4 is not supported [ 0.864438] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffe000 [ 0.880021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.880227] hub 2-0:1.0: USB hub found [ 0.880234] hub 2-0:1.0: 6 ports detected [ 0.880369] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.880396] uhci_hcd: USB Universal Host Controller Interface driver [ 0.880431] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.880443] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.880449] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.880529] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.880574] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff00 [ 0.880803] hub 3-0:1.0: USB hub found [ 0.880811] hub 3-0:1.0: 2 ports detected [ 0.880929] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.880940] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.880946] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.881039] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.881081] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000fe00 [ 0.881302] hub 4-0:1.0: USB hub found [ 0.881310] hub 4-0:1.0: 2 ports detected [ 0.881427] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.881438] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.881443] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.881523] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.881551] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000fd00 [ 0.881774] hub 5-0:1.0: USB hub found [ 0.881781] hub 5-0:1.0: 2 ports detected [ 0.881899] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.881910] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.881915] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.881993] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.882021] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fc00 [ 0.882244] hub 6-0:1.0: USB hub found [ 0.882252] hub 6-0:1.0: 2 ports detected [ 0.882370] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.882381] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.882386] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.882467] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.882495] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fb00 [ 0.882735] hub 7-0:1.0: USB hub found [ 0.882742] hub 7-0:1.0: 2 ports detected [ 0.882858] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.882869] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.882875] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.882954] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.882982] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fa00 [ 0.883205] hub 8-0:1.0: USB hub found [ 0.883213] hub 8-0:1.0: 2 ports detected [ 0.883435] usbcore: registered new interface driver libusual [ 0.883535] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.883926] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.883936] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.884187] mousedev: PS/2 mouse device common for all mice [ 0.884433] rtc_cmos 00:03: RTC can wake from S4 [ 0.884582] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 0.884612] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs [ 0.884719] device-mapper: uevent: version 1.0.3 [ 0.884854] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 0.884917] EISA: Probing bus 0 at eisa.0 [ 0.884921] EISA: Cannot allocate resource for mainboard [ 0.884925] Cannot allocate resource for EISA slot 1 [ 0.884929] Cannot allocate resource for EISA slot 2 [ 0.884932] Cannot allocate resource for EISA slot 3 [ 0.884936] Cannot allocate resource for EISA slot 4 [ 0.884940] Cannot allocate resource for EISA slot 5 [ 0.884943] Cannot allocate resource for EISA slot 6 [ 0.884947] Cannot allocate resource for EISA slot 7 [ 0.884950] Cannot allocate resource for EISA slot 8 [ 0.884954] EISA: Detected 0 cards. [ 0.884969] cpufreq-nforce2: No nForce2 chipset. [ 0.884973] cpuidle: using governor ladder [ 0.884976] cpuidle: using governor menu [ 0.884980] EFI Variables Facility v0.08 2004-May-17 [ 0.885476] TCP cubic registered [ 0.885708] NET: Registered protocol family 10 [ 0.886771] NET: Registered protocol family 17 [ 0.886799] Registering the dns_resolver key type [ 0.886837] Using IPI No-Shortcut mode [ 0.887028] PM: Hibernation image not present or could not be loaded. [ 0.887047] registered taskstats version 1 [ 0.902579] Magic number: 12:339:388 [ 0.902592] usb usb6: hash matches [ 0.902687] rtc_cmos 00:03: setting system clock to 2012-05-11 16:23:41 UTC (1336753421) [ 0.903185] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.903189] EDD information not available. [ 1.170710] ata3: SATA link down (SStatus 0 SControl 300) [ 1.181439] ata4: SATA link down (SStatus 0 SControl 300) [ 1.288020] Refined TSC clocksource calibration: 2499.999 MHz. [ 1.288028] Switching to clocksource tsc [ 1.292016] usb 1-5: new high-speed USB device number 3 using ehci_hcd [ 1.486745] ata2.00: SATA link down (SStatus 0 SControl 300) [ 1.486762] ata2.01: SATA link down (SStatus 0 SControl 300) [ 1.640115] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.640130] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.648342] ata1.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133 [ 1.648348] ata1.00: 490234752 sectors, multi 0: LBA48 [ 1.664325] ata1.00: configured for UDMA/133 [ 1.664531] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5 [ 1.664745] sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB) [ 1.664809] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.664838] sd 0:0:0:0: [sda] Write Protect is off [ 1.664843] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.664884] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.691699] sda: sda1 sda2 sda3 sda4 [ 1.692348] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.692461] Freeing unused kernel memory: 740k freed [ 1.692820] Write protecting the kernel text: 5828k [ 1.692851] Write protecting the kernel read-only data: 2376k [ 1.692854] NX-protecting the kernel data: 4412k [ 1.723980] udevd[92]: starting version 175 [ 1.865339] Floppy drive(s): fd0 is 1.44M [ 1.865429] pata_jmicron 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.865478] pata_jmicron 0000:03:00.0: setting latency timer to 64 [ 1.867875] sky2: driver version 1.30 [ 1.867926] sky2 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.867942] sky2 0000:04:00.0: setting latency timer to 64 [ 1.867979] sky2 0000:04:00.0: Yukon-2 EC chip revision 2 [ 1.868111] sky2 0000:04:00.0: irq 44 for MSI/MSI-X [ 1.868174] scsi4 : pata_jmicron [ 1.869802] sky2 0000:04:00.0: eth0: addr 00:01:29:a4:16:0a [ 1.869828] scsi5 : pata_jmicron [ 1.869943] ata5: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 16 [ 1.869949] ata6: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 16 [ 1.880053] usb 4-1: new full-speed USB device number 2 using uhci_hcd [ 1.884052] FDC 0 is a post-1991 82077 [ 2.032611] ata5.00: ATAPI: _NEC DVD+/-RW ND-3450A, 103C, max UDMA/33 [ 2.048585] ata5.00: configured for UDMA/33 [ 2.049777] scsi 4:0:0:0: CD-ROM _NEC DVD+-RW ND-3450A 103C PQ: 0 ANSI: 5 [ 2.051048] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 2.051054] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.051283] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 2.051483] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 2.079838] usbcore: registered new interface driver usbhid [ 2.079844] usbhid: USB HID core driver [ 2.236660] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 12.150230] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.177342] udevd[333]: starting version 175 [ 12.195524] Adding 417684k swap on /dev/sda2. Priority:-1 extents:1 across:417684k [ 12.278032] lp: driver loaded but no devices found [ 12.516456] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1a.1-1/input2 [ 12.520297] input: Logitech Unifying Device. Wireless PID:1024 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input2 [ 12.520753] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1024] on usb-0000:00:1a.1-1:1 [ 12.523286] input: Logitech Unifying Device. Wireless PID:2011 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input3 [ 12.524439] logitech-djdevice 0003:046D:C52B.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:2011] on usb-0000:00:1a.1-1:2 [ 12.545746] type=1400 audit(1336771433.137:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=502 comm="apparmor_parser" [ 12.546574] type=1400 audit(1336771433.137:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=502 comm="apparmor_parser" [ 12.547034] type=1400 audit(1336771433.137:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=502 comm="apparmor_parser" [ 12.626869] Linux video capture interface: v2.00 [ 12.649104] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081a) [ 12.668665] input: UVC Camera (046d:081a) as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5:1.0/input/input4 [ 12.668909] usbcore: registered new interface driver uvcvideo [ 12.668914] USB Video Class driver (1.1.1) [ 12.697645] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 12.697721] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 12.697760] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 12.706772] nvidia: module license 'NVIDIA' taints kernel. [ 12.706778] Disabling lock debugging due to kernel taint [ 12.735428] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 13.350252] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 13.350267] nvidia 0000:01:00.0: setting latency timer to 64 [ 13.350275] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem [ 13.351464] NVRM: loading NVIDIA UNIX x86 Kernel Module 295.40 Thu Apr 5 21:28:09 PDT 2012 [ 13.356785] hda_codec: ALC889A: BIOS auto-probing. [ 13.357267] init: failsafe main process (658) killed by TERM signal [ 13.372756] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5 [ 13.373173] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 13.373568] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 13.373954] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 13.374339] input: HDA Intel Line-Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 13.374715] input: HDA Intel Line-Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 13.375109] input: HDA Intel Line-Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 13.375724] input: HDA Intel Line-Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 13.475252] type=1400 audit(1336771434.065:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=735 comm="apparmor_parser" [ 13.477026] type=1400 audit(1336771434.069:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=735 comm="apparmor_parser" [ 13.477695] type=1400 audit(1336771434.069:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=735 comm="apparmor_parser" [ 13.479048] type=1400 audit(1336771434.069:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=734 comm="apparmor_parser" [ 13.488994] type=1400 audit(1336771434.081:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=738 comm="apparmor_parser" [ 13.489972] type=1400 audit(1336771434.081:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=738 comm="apparmor_parser" [ 13.

  Read the article

• What are some concise and comprehensive introductory guide to unit testing for a self-taught programmer [closed]

  - by Superbest

  I don't have much formal training in programming and I have learned most things by looking up solutions on the internet to practical problems I have. There are some areas which I think would be valuable to learn, but which ended up both being difficult to learn and easy to avoid learning for a self-taught programmer. Unit testing is one of them. Specifically, I am interested in tests in and for C#/.NET applications using Microsoft.VisualStudio.TestTools in Visual Studio 2010 and/or 2012, but I really want a good introduction to the principles so language and IDE shouldn't matter much. At this time I'm interested in relatively trivial tests for small or medium sized programs (development time of weeks or months and mostly just myself developing). I don't necessarily intend to do test-driven development (I am aware that some say unit testing alone is supposed to be for developing features in TDD, and not an assurance that there are no bugs in the software, but unit testing is often the only kind of testing for which I have resources). I have found this tutorial which I feel gave me a decent idea of what unit tests and TDD looks like, but in trying to apply these ideas to my own projects, I often get confused by questions I can't answer and don't know how to answer, such as: What parts of my application and what sorts of things aren't necessarily worth testing? How fine grained should my tests be? Should they test every method and property separately, or work with a larger scope? What is a good naming convention for test methods? (since apparently the name of the method is the only way I will be able to tell from a glance at the test results table what works in my program and what doesn't) Is it bad to have many asserts in one test method? Since apparently VS2012 reports only that "an Assert.IsTrue failed within method MyTestMethod", and if MyTestMethod has 10 Assert.IsTrue statements, it will be irritating to figure out why a test is failing. If a lot of the functionality deals with writing and reading data to/from the disk in a not-exactly trivial fashion, how do I test that? If I provide a bunch of files as input by placing them in the program's directory, do I have to copy those files to the test project's bin/Debug folder now? If my program works with a large body of data and execution takes minutes or more, should my tests have it do the whole use all of the real data, a subset of it, or simulated data? If latter, how do I decide on the subset or how to simulate? Closely related to the previous point, if a class is such that its main operation happens in a state that is arrived to by the program after some involved operations (say, a class makes calculations on data derived from a few thousands of lines of code analyzing some raw data) how do I test just that class without inevitably ending up testing that class and all the other code that brings it to that state along with it? In general, what kind of approach should I use for test initialization? (hopefully that is the correct term, I mean preparing classes for testing by filling them in with appropriate data) How do I deal with private members? Do I just suck it up and assume that "not public = shouldn't be tested"? I have seen people suggest using private accessors and reflection, but these feel like clumsy and unsuited for regular use. Are these even good ideas? Is there anything like design patterns concerning testing specifically? I guess the main themes in what I'd like to learn more about are, (1) what are the overarching principles that should be followed (or at least considered) in every testing effort and (2) what are popular rules of thumb for writing tests. For example, at one point I recall hearing from someone that if a method is longer than 200 lines, it should be refactored - not a universally correct rule, but it has been quite helpful since I'd otherwise happily put hundreds of lines in single methods and then wonder why my code is so hard to read. Similarly I've found ReSharpers suggestions on member naming style and other things to be quite helpful in keeping my codebases sane. I see many resources both online and in print that talk about testing in the context of large applications (years of work, 10s of people or more). However, because I've never worked on such large projects, this context is very unfamiliar to me and makes the material difficult to follow and relate to my real world problems. Speaking of software development in general, advice given with the assumptions of large projects isn't always straightforward to apply to my own, smaller endeavors. Summary So my question is: What are some resources to learn about unit testing, for a hobbyist, self-taught programmer without much formal training? Ideally, I'm looking for a short and simple "bible of unit testing" which I can commit to memory, and then apply systematically by repeatedly asking myself "is this test following the bible of testing closely enough?" and then amending discrepancies if it doesn't.

  Read the article

• How to Mock HttpWebRequest and HttpWebResponse using the Moq Framework?

  - by Nicholas

  How do you use the Moq Framework to Mock HttpWebRequest and HttpWebResponse in the following Unit Test? [Test] public void Verify_That_SiteMap_Urls_Are_Reachable() { // Arrange - simplified Uri uri = new Uri("http://www.google.com"); // Act HttpWebRequest request = (HttpWebRequest)WebRequest.Create(uri); HttpWebResponse response = (HttpWebResponse)request.GetResponse(); // Asset Assert.AreEqual("OK", response.StatusCode.ToString()); }

  Read the article

• Creating Entity Framework objects with Unity for Unit of Work/Repository pattern

  - by TobyEvans

  Hi there, I'm trying to implement the Unit of Work/Repository pattern, as described here: http://blogs.msdn.com/adonet/archive/2009/06/16/using-repository-and-unit-of-work-patterns-with-entity-framework-4-0.aspx This requires each Repository to accept an IUnitOfWork implementation, eg an EF datacontext extended with a partial class to add an IUnitOfWork interface. I'm actually using .net 3.5, not 4.0. My basic Data Access constructor looks like this: public DataAccessLayer(IUnitOfWork unitOfWork, IRealtimeRepository realTimeRepository) { this.unitOfWork = unitOfWork; this.realTimeRepository = realTimeRepository; } So far, so good. What I'm trying to do is add Dependency Injection using the Unity Framework. Getting the EF data context to be created with Unity was an adventure, as it had trouble resolving the constructor - what I did in the end was to create another constructor in my partial class with a new overloaded constructor, and marked that with [InjectionConstructor] [InjectionConstructor] public communergyEntities(string connectionString, string containerName) :this() { (I know I need to pass the connection string to the base object, that can wait until once I've got all the objects initialising correctly) So, using this technique, I can happily resolve my entity framework object as an IUnitOfWork instance thus: using (IUnityContainer container = new UnityContainer()) { container.RegisterType<IUnitOfWork, communergyEntities>(); container.Configure<InjectedMembers>() .ConfigureInjectionFor<communergyEntities>( new InjectionConstructor("a", "b")) DataAccessLayer target = container.Resolve<DataAccessLayer>(); Great. What I need to do now is create the reference to the repository object for the DataAccessLayer - the DAL only needs to know the interface, so I'm guessing that I need to instantiate it as part of the Unity Resolve statement, passing it the appropriate IUnitOfWork interface. In the past, I would have just passed the Repository constructor the db connection string, and it would have gone away, created a local Entity Framework object and used that just for the lifetime of the Repository method. This is different, in that I create an Entity Framework instance as an IUnitOfWork implementation during the Unity Resolve statement, and it's that instance I need to pass into the constructor of the Repository - is that possible, and if so, how? I'm wondering if I could make the Repository a property and mark it as a Dependency, but that still wouldn't solve the problem of how to create the Repository with the IUnitOfWork object that the DAL is being Resolved with I'm not sure if I've understood this pattern correctly, and will happily take advice on the best way to implement it - Entity Framework is staying, but Unity can be swapped out if not the best approach. If I've got the whole thing upside down, please tell me thanks

  Read the article

• Doing TDD Silverlight 4 RC using Visual Studio 2010 RC

  - by user133992

  First I am glad to see better TDD support in VS2010. Support for generating code stubs from my tests is ok - not as good as more mature TDD plug-ins but a good start. I am looking for some best Silverlight 4.0 TDD practices. First Question: Anyone have links, recommendations? I know the new Silverlight Unit Test capabilities are much better (Jeff Wilcox's Mix Presentation). What I am focusing on right now is using TDD to develop pure Silverlight 4.0 Class Library projects - projects without a Silverlight UI project. I've been able to get it to work but not as cleanly as it should be. I can create an Empty VS project. Add A Silverlight 4 Class Library Project. Add a TestProject (not a silverlight Unit Test Project but a plain Test Project). Add a simple test in the Test Project such as: namespace Calculator.Test { [TestClass] public class CalculatorTests { [TestMethod] public void CalulatorAddTest() { Calc c = new Calc(); int expected = 10; int actual = c.Add(6, 4); Assert.AreEqual<int>(expected, actual); } } } Using the new Generate Type and Method from Test feature it will generate the following code in the Silverlight Project: namespace Calculator { public class Calc { public int Add(int p, int p_2) { throw new NotImplementedException(); } } } When I run the tests the first time it says the target assembly is Silverlight and not able to run test - Not exact text but the same general idea. When I change the implementation to: namespace Calculator { public class Calc { public int Add(int p, int p_2) { return p + p_2; } } } and re-run the test, it works fine and the test goes green. It also works for all other TDD code I generate after. I also get a warning Mark in the Test Project's reference to the Calculator Silverlight Class Library Assembly. Second Question: Any comments ideas if this just a bug in VS2010 RC or is Silverlight Class Library TDD not really supported. I have not created a Silverlight UI project or changed and build or debug settings so I have no idea what is hosting the silverlight DLL. Finally, some of the Silverlight Class Libraries I need to write will provide functionality that requires elevated Out-Of-Browser rights. Based on the above, it looks like I can use TDD Test Projects against regular Silverlight 4.0 Class Libraries, but I have no idea how I can TDD the elevated OOB functionality without also creating the UI component that gets installed. The UI piece is not really needed for the Library development and gets in the way of what I actually want to TDD. I know I can (and will) mock some of that functionality but at some point I will also need the real thing in my tests. Third Question: Any ideas how to TDD Silverlight 4.0 Class Library project that requires OOB elevated rights? Thanks!

  Read the article

• EF4 - possible to mock ObjectContext for unit testing?

  - by steve.macdonald

  Can it be done without using TypeMock Islolator? I've found a few suggestions online such as passing in a metadata only connection string, however nothing I've come across besides TypeMock seems to truly allow for a mock ObjectContext that can be injected into services for unit testing. Do I plunk down the $$ for TypeMock, or are there alternatives? Has nobody managed to create anything comparable to TypeMock that is open source?

  Read the article

• .NET 3.0 Unit Testing getting System.MethodAccessException calling .NET 2.0

  - by NealWalters

  Is there any way to get around this exception? Can I not call a .NET 2.0 from 3.5? I have to write .NET 2.0 to maintain capability with BizTalk 2006/R2. But I would like to test with VS2008 Unit Tests to be consistent to other non-BizTalk code that we are testing. Test method ABC.UnitTest.UnitTest1.TestReferenceCode1 threw exception: System.MethodAccessException: ABC.EasyRegEx.extractUsingRegEx(System.String, System.String).

  Read the article

• Unit of Measurement for Duration Column in Sql Profiler

  - by Mubashar Ahmad

  What is the Unit of Duration column in SQL Profiler? i thought it is milliseconds but in following profiler row i found it contradicting with start and end time spid=163 duration=11310646 starttime=2010-04-06 17:45:24.480 endtime=2010-04-06 17:45:35.790 reads=152 writes=2 cpu=16 eventclass=12 textdata= DELETE FROM dbo.[Icon] WHERE Id = 20087

  Read the article

• EJB3 - using 2 persistence units within a transaction (Exception: Local transaction already has 1 no

  - by Sorcha

  I am trying to use 2 persistence units within the same transaction in a JEE application deployed on Glassfish. The 2 persistence units are defined in persistence.xml, as follows: <persistence-unit name="BeachWater"> <jta-data-source>jdbc/BeachWater</jta-data-source> ... <persistence-unit name="LIMS"> <jta-data-source>jdbc/BeachWaterLIMS</jta-data-source> ... These persistence units correspond to JDBC resources and connection pools which I had defined in Glassfish as follows (include one here as both are identical apart from names & database connection info): JDBC Resource: JNDI Name: jdbc/BeachWaterLIMS Pool Name: BEACHWATER_LIMS Connection Pool: Name: BEACHWATER_LIMS Datasource Classname: com.microsoft.sqlserver.jdbc.SQLServerConnectionPoolDataSource Resource Type: javax.sql.ConnectionPoolDataSource There are 3 stateless session beans, LimsServiceBean, AnalysisServiceBean and AnalysisDataTransformationServiceBean. Here are the relevant snippets from LimsServiceBean: @PersistenceContext(unitName = "LIMS") EntityManager em; ... public ArrayList<Sample> getLatestLIMSData() { Query q = em.createNamedQuery("Sample.findBySubTypeStatus"); return new ArrayList<Sample>(q.getResultList()); } From AnalysisServiceBean: @PersistenceContext(unitName = "BeachWater") EntityManager em; ... public ArrayList<AnalysisType> getAllAnalysisTypes() { Query q = em.createNamedQuery("AnalysisType.findAll"); return new ArrayList<AnalysisType>(q.getResultList()); } And from AnalysisDataTransformationServiceBean: @EJB private AnalysisService analysisService; @EJB private LimsService limsService; public void transformData() { List<AnalysisType> analysisTypes = analysisService.getAllAnalysisTypes(); ArrayList<Sample> samples = limsService.getLatestLIMSData(); This call to limsService.getLatestLIMSData() caused the following exception: [exec] Caused by: javax.ejb.TransactionRolledbackLocalException: Exception thrown from bean; nested exception is: Exception [TOPLINK-4002] (Oracle TopLink Essentials - 2.1 (Build b60e-fcs (12/23/2008))): oracle.toplink.essentials.exceptions.DatabaseException [exec] Internal Exception: java.sql.SQLException: Error in allocating a connection. Cause: java.lang.IllegalStateException: Local transaction already has 1 non-XA Resource: cannot add more resources. Having consulted this page, http://msdn.microsoft.com/en-us/library/ms378484.aspx (among many others), I tried changing the definition of the connection pools to: Connection Pool: Name: BEACHWATER_LIMS Datasource Classname: com.microsoft.sqlserver.jdbc.SQLServerXADataSource Resource Type: javax.sql.XADataSource Ping via the Glassfish admin console succeeds, but call to analysisService.getAllAnalysisTypes() now throws an exception: Caused by: javax.ejb.TransactionRolledbackLocalException: Exception thrown from bean; nested exception is: Exception [TOPLINK-4002] (Oracle TopLink Essentials - 2.1 (Build b60e-fcs (12/23/2008))): oracle.toplink.essentials.exceptions.DatabaseException Internal Exception: java.sql.SQLException: Error in allocating a connection. Cause: javax.transaction.SystemException Any ideas?

  Read the article

• How do I assert that a model has a readable/writable attribute?

  - by TheDeeno

  In one of my model's I'm using some meta programming to dynamically define some methods. I'd like to test this. I need a compact way to assert that my model has readable/writable attribute with a certain name. Ideas? I'm using shoulda for unit testing if it makes a difference.

  Read the article

• Is there any way to test server side code using JSTestDriver?

  - by dhackner

  I'm new to JS unit testing and I like what I've read about JSTestDriver. The idea of have the suite run every time you save is pretty cool. JSTestDriver runs Javascript in a browser sandbox and PHP runs on the server. If the browser slaves can serve from an arbitrary server is there any reason that you couldn't test it via AJAX? It this a misuse/misunderstanding of what the framework is for? Any clarifications are appreciated.

  Read the article

• Testing Python Decorators?

  - by Jama22

  I'm writing some unit tests for a Django project, and I was wondering if its possible (or necessary?) to test some of the decorators that I wrote for it. Here is an example of a decorator that I wrote: class login_required(object): def __init__(self, f): self.f = f def __call__(self, *args): request = args[0] if request.user and request.user.is_authenticated(): return self.f(*args) return redirect('/login')

  Read the article

• DUnit: How to run tests?

  - by Ian Boyd

  How do i run TestCase's from the IDE? i created a new project, with a single, simple, form: unit Unit1; interface uses Windows, Messages, SysUtils, Classes, Graphics, Controls, Forms, Dialogs, StdCtrls; type TForm1 = class(TForm) private public end; var Form1: TForm1; implementation {$R *.DFM} end. Now i'll add a test case to check that pushing Button1 does what it should: unit Unit1; interface uses Windows, Messages, SysUtils, Classes, Graphics, Controls, Forms, Dialogs, StdCtrls; type TForm1 = class(TForm) Button1: TButton; procedure Button1Click(Sender: TObject); private public end; var Form1: TForm1; implementation {$R *.DFM} uses TestFramework; type TForm1Tests = class(TTestCase) private f: TForm1; protected procedure SetUp; override; procedure TearDown; override; published procedure TestButton1Click; end; procedure TForm1.Button1Click(Sender: TObject); begin //todo end; { TForm1Tests } procedure TForm1Tests.SetUp; begin inherited; f := TForm1.Create(nil); end; procedure TForm1Tests.TearDown; begin f.Free; inherited; end; procedure TForm1Tests.TestButton1Click; begin f.Button1Click(nil); Self.CheckEqualsString('Hello, world!', f.Caption); end; end. Given what i've done (test code in the GUI project), how do i now trigger a run of the tests? If i push F9 then the form simply appears: Ideally there would be a button, or menu option, in the IDE saying Run DUnit Tests: Am i living in a dream-world? A fantasy land, living in a gumdrop house on lollipop lane?

  Read the article

• Using Selenium, how can I test a web UI that returns XML instead of HTML?

  - by Kurt W. Leucht

  I'm using Selenium to unit test my Perl cgi script and all works fine except in one case where my cgi script returns XML content to the web browser instead of returning HTML content. I'm new to Selenium and only pasted in their sample script to get started, but I can't seem to find a Selenium command in any of the documentation that will recognize that my XML response has been returned. The Selenium commands seem to assume that an HTML page is always being returned.

  Read the article

• Real website/-application use cases where dependency injection was useful (excluding unit testing/mo

  - by fireeyedboy

  In what concrete web project(s), specifically what part of the web-application/website, that you have worked on, has dependency injection proven to be a good choice. Can you give concrete examples where you actually substituted one component for another with DI during the life span of the project, excluding cases for mock/unit testing?

  Read the article

• Python - doctest vs. unittest

  - by Sean

  I'm trying to get started with unit testing in Python and I was wondering if someone could inform me of the advantages and disadvantages of doctest and unittest. What conditions would you use each for?

  Read the article

• Rail test case fixtures not loading

  - by Deano

  Rails appears to not be loading any fixtures for unit or functional tests. I have a simple 'products.yml' that parses and appears correct: ruby: title: Programming Ruby 1.9 description: Ruby is the fastest growing and most exciting dynamic language out there. If you need to get working programs delivered fast, you should add Ruby to your toolbox. price: 49.50 image_url: ruby.png My controller functional test begins with: require 'test_helper' class ProductsControllerTest < ActionController::TestCase fixtures :products setup do @product = products(:one) @update = { :title => 'Lorem Ipsum' , :description => 'Wibbles are fun!' , :image_url => 'lorem.jpg' , :price => 19.95 } end According to the book, Rails should "magically" load the fixtures (as my test_helper.rb has fixtures :all in it. I also added the explicit fixtures load (seen above). Yes Rails complains: user @ host ~/Dropbox/Rails/depot > rake test:functionals (in /Somewhere/Users/user/Dropbox/Rails/depot) /System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/bin/ruby -Ilib:test "/System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib/ruby/gems/1.8/gems/rake-0.8.3/lib/rake/rake_test_loader.rb" "test/functional/products_controller_test.rb" Loaded suite /System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib/ruby/gems/1.8/gems/rake-0.8.3/lib/rake/rake_test_loader Started EEEEEEE Finished in 0.062506 seconds. 1) Error: test_should_create_product(ProductsControllerTest): NoMethodError: undefined method `products' for ProductsControllerTest:Class /test/functional/products_controller_test.rb:7 2) Error: test_should_destroy_product(ProductsControllerTest): NoMethodError: undefined method `products' for ProductsControllerTest:Class /test/functional/products_controller_test.rb:7 ... I did come across the other Rails test fixture question http://stackoverflow.com/questions/1547634/rails-unit-testing-doesnt-load-fixtures, but that leads to a plugin issue (something to do with the order of loading fixtures). BTW, I am developing on Mac OS X 10.6 with Rail 2.3.5 and Ruby 1.8.7, no additional plugins (beyond the base install). Any pointers on how to debug, why the magic of Rails appears to be failing here? Is it a version problem? Can I trace code into the libraries and find the answer? There are so many "mixin" modules I can't find where the fixtures method really lives.

  Read the article

• Testing tools for Django Project

  - by Bharath

  Can anyone please suggest me some good testing tools for a django project? I need to test the different use case scenarios, unit testing, as well as load testing for my project. Is there any good standard testing suite available?? Any other suggestion(s) for the testing process is greatly appreciated. I use Django, postgresql on Ubuntu server if this information is necessary.

  Read the article

• Cannot parse persistence unit from class path resource

  - by Grzegorz S

  so I have this problem in running my Spring WS app which implements JPA ( or should implement..) I have a problem with running a WS, it looks like my Spring context can't find file persistence.xml Which i am able to believe because i did not have generated META-INF folder in my template (which is Maven project template with archetype org.springframework.ws) I have created META-INF manually. Here is the HTTP 500: org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'caChainDao' defined in file [E:\STS\vfabric-tc-server-developer-2.7.2.RELEASE\zz\wtpwebapps\FCAWSv4\WEB-INF\classes\pl\famoc\test\ws\db\dao\caChainDao.class]: Initialization of bean failed; nested exception is org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'entityManagerFactory' defined in ServletContext resource [/WEB-INF/spring-ws-servlet.xml]: Invocation of init method failed; nested exception is java.lang.IllegalArgumentException: Cannot parse persistence unit from class path resource [persistence.xml] org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.doCreateBean(AbstractAutowireCapableBeanFactory.java:527) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBean(AbstractAutowireCapableBeanFactory.java:456) org.springframework.beans.factory.support.AbstractBeanFactory$1.getObject(AbstractBeanFactory.java:294) org.springframework.beans.factory.support.DefaultSingletonBeanRegistry.getSingleton(DefaultSingletonBeanRegistry.java:225) org.springframework.beans.factory.support.AbstractBeanFactory.doGetBean(AbstractBeanFactory.java:291) org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:193) org.springframework.beans.factory.support.DefaultListableBeanFactory.preInstantiateSingletons(DefaultListableBeanFactory.java:609) org.springframework.context.support.AbstractApplicationContext.finishBeanFactoryInitialization(AbstractApplicationContext.java:918) org.springframework.context.support.AbstractApplicationContext.refresh(AbstractApplicationContext.java:469) org.springframework.web.servlet.FrameworkServlet.configureAndRefreshWebApplicationContext(FrameworkServlet.java:631) org.springframework.web.servlet.FrameworkServlet.createWebApplicationContext(FrameworkServlet.java:588) org.springframework.web.servlet.FrameworkServlet.createWebApplicationContext(FrameworkServlet.java:645) org.springframework.web.servlet.FrameworkServlet.initWebApplicationContext(FrameworkServlet.java:508) org.springframework.web.servlet.FrameworkServlet.initServletBean(FrameworkServlet.java:449) org.springframework.web.servlet.HttpServletBean.init(HttpServletBean.java:133) javax.servlet.GenericServlet.init(GenericServlet.java:160) org.apache.catalina.authenticator.AuthenticatorBase.invoke(AuthenticatorBase.java:472) org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:99) org.apache.catalina.valves.AccessLogValve.invoke(AccessLogValve.java:929) org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:407) org.apache.coyote.http11.AbstractHttp11Processor.process(AbstractHttp11Processor.java:1002) org.apache.coyote.AbstractProtocol$AbstractConnectionHandler.process(AbstractProtocol.java:585) org.apache.tomcat.util.net.JIoEndpoint$SocketProcessor.run(JIoEndpoint.java:310) java.util.concurrent.ThreadPoolExecutor.runWorker(ThreadPoolExecutor.java:1110) java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:603) java.lang.Thread.run(Thread.java:722) Here it is my persistence.xml <?xml version="1.0" encoding="UTF-8" ?> <persistence xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/persistence http://java.sun.com/xml/ns/persistence/persistence_2_0.xsd" version="2.0" xmlns="http://java.sun.com/xml/ns/persistence"> <persistence-unit name="persistenceUnit" transaction-type="RESOURCE_LOCAL" /> </persistence> here it is where i am looking for it <property name="persistenceXmlLocation" value="classpath:persistence.xml" /> and here it is path to this xml in my classpath: src/main/webapp/META-INF/persistence.xml Could anyone give me a hint what am i missing?

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >