Search Results

Search found 5121 results on 205 pages for 'dotnetnuke connections'.

Page 67/205 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Mangling traffic from a Mikrotik Router

  - by TiernanO

  I have a MikroTik powered Router in the house with a couple of internet connections (2 200/10Mb Cable modems and a 100/20Mb VDSL Line). I am using Mangle rules to set routing marks and NAT rules to do some load balancing, and everything seems to be going grand... But it only works for traffic from outside the router... Let me explain: I have 4 GigE ports on the machine, WAN1,2 and 3, and a LAN port named LAN1. All traffic from LAN1 is getting mangled (as it should be) but traffic from the load router itself (proxy traffic, IPv6 tunnels, VPN connections) are not being mangled. They get the first route to 0.0.0.0/0, which in my case is WAN2, and stick with it. So, how do I get traffic from the local router to be mangled? Originally it was proxy traffic that caused the problem, but now with IPv6 and VPN, they are more important to be mangled... last time i enabled IPv6 traffic, all traffic only went though WAN2, and the rest where unused... Any ideas?

  Read the article

• Last (I think and hope) problems configuring SSL certificate with Apache and VirtualHosts

  - by user65567

  Finally I set apache2 to get a single certificate for all subdomains. [...] # Go ahead and accept connections for these vhosts # from non-SNI clients SSLStrictSNIVHostCheck off # Apache setup which will listen for and accept SSL connections on port 443. Listen 443 # Listen for virtual host requests on all IP addresses NameVirtualHost *:443 # Because this virtual host is defined first, it will # be used as the default if the hostname is not received # in the SSL handshake, e.g. if the browser doesn't support # SNI. <VirtualHost *:443> ServerName domain.localhost DocumentRoot "/Users/<my_user_name>/Sites/domain/public" <Directory "/Users/<my_user_name>/Sites/domain/public"> Order allow,deny Allow from all </Directory> # SSL Configuration SSLEngine on ... </VirtualHost> <VirtualHost *:443> ServerName subdomain1.domain.localhost DocumentRoot "/Users/<my_user_name>/Sites/subdomain1/public" <Directory "/Users/<my_user_name>/Sites/subdomain1/public"> Order allow,deny Allow from all </Directory> # SSL Configuration SSLEngine on ... </VirtualHost> <VirtualHost *:443> ServerName subdomain2.domain.localhost DocumentRoot "/Users/<my_user_name>/Sites/subdomain2/public" <Directory "/Users/<my_user_name>/Sites/subdomain2/public"> Order allow,deny Allow from all </Directory> # SSL Configuration SSLEngine on ... </VirtualHost> So, for example, I can correctly access https://subdomain1.domain.localhost https://subdomain2.domain.localhost ... Now, anyway, I have problems on accessing http://subdomain1.domain.localhost http://subdomain2.domain.localhost ... Since I use a Mac Os, on accessing the "http: version", I get a default page "Your website." (instead of a error). Why does it happen?

  Read the article

• postfix - connection refused from behind NAT

  - by manchine

  When attempting to telnet postfix from a different host in the same LAN through the FQDN (and thus the LAN's public IP), the following error occurs: root@mailer:/var/log# telnet mail.domain.com 25 Trying 1.2.3.4... telnet: Unable to connect to remote host: Connection refused Other services can be reached from the exact same host, however: root@mailer:/var/log# telnet mail.domain.com 22 Trying 1.2.3.4... Connected to mail.domain.com. Escape character is '^]'. SSH-2.0-OpenSSH_6.0p1 Debian-4+deb7u1 To make matters more intriguing, Postfix can be accessed from outside the LAN: nunos-mbp:mailog nzimas$ telnet mail.domain.com 25 Trying 1.2.3.4... Connected to mail.domain.com. Escape character is '^]'. 220 mail.domain.com ESMTP Postfix (Ubuntu) To sum thing up: a) Postfix (running on 10.10.10.4 / mail.domiain.com) refuses connection from a host in the same LAN (10.10.10.2), but only when queried through the FQDN (mail.domain.com) b) mail.domain.com accepts connections to other services (but Postfix) from 10.10.10.2 c) mail.domain.com accepts connections to all services, including Postfix, from the outside world If it were a firewall issue, then I believe it would not be possible to connect to any service from 10.10.10.2 through the FQSN / public IP. It ought to be some missing parameter in Postfix, although I haven't found any clear pointers so far.

  Read the article

• Iptables ignoring a rule in the config file

  - by Overdeath

  I see lot of established connections to my apache server from the ip 188.241.114.22 which eventually causes apache to hang . After I restart the service everything works fine. I tried adding a rule in iptables -A INPUT -s 188.241.114.22 -j DROP but despite that I keep seeing connections from that IP. I'm using centOS and i'm adding the rule like thie: iptables -A INPUT -s 188.241.114.22 -j DROP Right afther that I save it using: service iptables save Here is the output of iptables -L -v ` Chain INPUT (policy ACCEPT 120K packets, 16M bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any c-98-210-5-174.hsd1.ca.comcast.net anywhere 0 0 DROP all -- any any c-98-201-5-174.hsd1.tx.comcast.net anywhere 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any www.dabacus2.com anywhere 0 0 DROP all -- any any 116.255.163.100 anywhere 0 0 DROP all -- any any 94.23.119.11 anywhere 0 0 DROP all -- any any 164.bajanet.mx anywhere 0 0 DROP all -- any any 173-203-71-136.static.cloud-ips.com anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any 74.122.177.12 anywhere 0 0 DROP all -- any any 58.83.227.150 anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 186K packets, 224M bytes) pkts bytes target prot opt in out source destination `

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Sharing between Vista and Windows 7

  - by Metro Smurf

  Vista Ultimate 32 bit Windows 7 Ultimate 64 bit I've read through similar questions about sharing between Win7 and Vista, but none of them have resolved my issue of not being able to share between Win7 and Vista: Connecting to a Vista shared folder from Windows 7 Networking Windows 7 and Vista Enable File sharing in Windows Vista Previously I had previously had my Vista and XP system sharing back and forth without any problems. I was able to access the shares without entering a user name / password in the NT challenge prompt (note: account names and passwords were different on the Vista and XP systems). Currently I replaced my XP system with a Win7 system. Now, when I attempt to access shares to/from Vista / Win7, I am continually prompted with an NT challenge to enter my credentials. Things I've Verified/Tried Both systems are on the same workgroup. Win 7 is using the Home network. Vista is using the Private network. In other words, neither system is using a Public network profile. Enabled file sharing with and without password protection on both Vista and Win7 Tried HomeGroup Connections (win7) with Windows to manage connections and Use user accounts to connect. Reviewed too many online articles to count to trouble shoot. Set the shares to have full control by everyone. Set up the shares directly on the directory and through the share manager. My Question How can I enable file sharing between Vista and Win7 without being prompted with a username/password challenge, ever?

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Connection failed between Windows Servers

  - by Kerby82

  I'm setting up an infrastructure based on Windows Server 2012. The firewall is turned off and I can't access the Domain controller to check for the group policy. I'm experiencing some connection problem between servers. All the servers are running a site on the TCP Port 80 and I check with netstat that the web server is binding on every Ip of the servers. If i try to telnet from the server itself on the port 80 it works (using DNS name) if I try same telnet from another machine I get connection failed. The DNS works, the ping is successfull, the servers are on the same subnet, the firewall is turned off (even though windows advanced firewall says that some settings can be managed by the System Administrator, i guess group policy). I don't know how to troubleshoot further. Do you have any idea? Is that possible that the FW looks turned off but there are some group policy blocking the connections? (I also check group policy-Administrative Template-Network Connections- Windows FW everything is not configured) I need some hint on how to keep troubleshooting such a problem.

  Read the article

• How do I force a restore over an existing database?

  - by Ian Boyd

  I have a database, and i want to force a restore over top of it. I check the option: Overwrite the existing database (WITH REPLACE) But, as expected, SSMS is unable to overwrite the existing database. Of course i don't want different filenames; i want to overwrite the existing database. How do i force a restore over an existing database? And for Google search crawler: File '%s' is claimed by '%s'(4) and '%s"(3). The WITH MOVE clause can be used to relocate one or more files. RESTORE DATABASE is terminating abnormally. (Microsoft SQL Server, Error: 3176) Update The script (before i deleted the database, because i needed to get it done) was: RESTORE DATABASE [HealthCareGovManager] FILE = N'HealthCareGovManager_Data', FILE = N'HealthCareGovManager_Archive', FILE = N'HealthCareGovManager_AuditLog' FROM DISK = N'D:\STAGING\HealthCareGovManager10232013.bak' WITH FILE = 1, MOVE N'HealthCareGovManager_Data' TO N'D:\CGI Data\HealthCareGovManager.MDF', MOVE N'HealthCareGovManager_Archive' TO N'D:\CGI Data\HealthCareGovManager.ndf', MOVE N'HealthCareGovManager_AuditLog' TO N'D:\CGI Data\HealthCareGovManager.ndf', MOVE N'HealthCareGovManager_Log' TO N'D:\CGI Data\HealthCareGovManager.LDF', NOUNLOAD, REPLACE, STATS = 10 I used the UI to delete the existing database, so that i could use the UI to force an overwrite of the (non)existing database. Hopefully there can be an answer so that the next guy can have an answer. No, nobody was in the context of the database (The error message from other connections is quite different from this error, and i only got to see this error after i killed the other connections).

  Read the article

• How to configure network on Windows Server 2008

  - by Gokhan Ozturk

  I have a IBM x3400 Server Machine with Windows Server 2008 R2 installed on it. But, since I am not expert on networking I have some problems. These roles installed on my server: Active Directory DNS File Sharing Hyper-V ISS VPN There is two network card on them. I configured them like this: Local Connection 1: 192.168.30.3 255.255.255.0 192.168.30.2 127.0.0.1 Local Connection 2: 192.168.30.101 255.255.255.0 192.168.30.6 127.0.0.1 My problem is, when I use this Ip gateways, It is sharing internet to all computers. This is not I want. I want to use Local Connection 1 for internal network. I am giving all computers gateway and DNS IP as 192.168.30.3 The Local Connection 2 is for Hyper-V and VPN connections. 192.168.30.2 and 192.168.30.6 are my modem's gateways. I am using 192.168.30.6 external IP for VPN connections. There is two 24 port switches. There is a connection between them and this two ethernet card connected directly to them. And modems are connected to switches as well (Morems are not near the server. They are somewhere in the building). I disabled network Bridge and removed all ethernet cards from it. With this configuration, all computers can ping my server's IP (192.168.30.3) but on server I cannot ping any clients (Request timeout). What is the best way to configure my network? Thank you. Redgards

  Read the article

• Is this a good starting point for iptables in Linux?

  - by sbrattla

  Hi, I'm new to iptables, and i've been trying to put together a firewall which purpose is to protect a web server. The below rules are the ones i've put together so far, and i would like to hear if the rules makes sense - and wether i've left out anything essential? In addition to port 80, i also need to have port 3306 (mysql) and 22 (ssh) open for external connections. Any feedback is highly appreciated! #!/bin/sh # Clear all existing rules. iptables -F # ACCEPT connections for loopback network connection, 127.0.0.1. iptables -A INPUT -i lo -j ACCEPT # ALLOW established traffic iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # DROP packets that are NEW but does not have the SYN but set. iptables -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # DROP fragmented packets, as there is no way to tell the source and destination ports of such a packet. iptables -A INPUT -f -j DROP # DROP packets with all tcp flags set (XMAS packets). iptables -A INPUT -p tcp --tcp-flags ALL ALL -j DROP # DROP packets with no tcp flags set (NULL packets). iptables -A INPUT -p tcp --tcp-flags ALL NONE -j DROP # ALLOW ssh traffic (and prevent against DoS attacks) iptables -A INPUT -p tcp --dport ssh -m limit --limit 1/s -j ACCEPT # ALLOW http traffic (and prevent against DoS attacks) iptables -A INPUT -p tcp --dport http -m limit --limit 5/s -j ACCEPT # ALLOW mysql traffic (and prevent against DoS attacks) iptables -A INPUT -p tcp --dport mysql -m limit --limit 25/s -j ACCEPT # DROP any other traffic. iptables -A INPUT -j DROP

  Read the article

• rdp allow client reconnect without password prompt after several hours

  - by Tom

  Let me describe the setup first: client PC with several rdp sessions to local servers, all opened from saved rdp sessions with stored passwords, using the standard windows rdp client. several windows servers on the LAN, with varying server OS: windows server 2003, 2008, and even 2012 now. When I log onto my PC I open up rdp sessions to all those servers, and keep them open all the time for various reasons. Overnight the client PC is put into sleep or hibernate mode, thereby braking the rdp connections. On the next day when I wake the client PC and login again, the rdp sessions automatically try to reconnect to the servers, and this leads to the question: starting with server 2008 something apparently changed in the rdp server config, as all servers with 2008, 2008r2 and 2012 will prompt for the password in the rdp session, whereas the 2003 server rdp connections will re-establish without the password prompt. Apparently there is a timeout setting on 2008+ that, when exceeded, requires a reauthentication. Is there any way to setup the 2008+ servers to behave like 2003 did? I'd like the rdp sessions to reconnect without a password prompt even after a several hour disconnect.

  Read the article

• System With Two Network Adapters

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• Multiple Routers, Failover, DHCP and multiple gateways. NOT WAN-failover

  - by u_b

  I've had a look around google and this forum but could not find an answer to my question. So probably one of you can help me a little. My intended setup is: Router R1: wan connection to isp. connected backup server. provides some wireless SSID. other connected devices like printer, laptop, etc. both wired and wireless. Router R2: no wan connection to isp but connected to R2. connects mp3-streamer and music server. also serves as a wireless access point with same SSID. other than described connections only wireless connections. I would like to be able to control music even if R1 is off, e.g. with no internet connection. On the other hand I would like to access internet also in the case that R2 is off, i.e. no music access. Last but not least I would like to stream internet radio, i.e., R1 and R2 are on, and music is streamed from internet to R1 to R2 to streamer. I would like to realize all this using DHCP (also using static assignments) so i do not have to configure statically on android, laptop, etc. So my questions are: Can I make DHCP provide a list of two default gateways R1,R2? In order to make clients fallback to other gateway if currently assigned gateway is turned off? Thanks in advance, u_b

  Read the article

• Computer won't start after installing new video card

  - by Vercas

  So, 1 year and 340 days ago I bought a desktop computer. Since then, it has served me well. But lately, I wanted an upgrade, so I bought a new video card. I documented myself about the compatibility, and it is okay. So I opened the case, cleaned up that... dust elemental living inside of it. Unscrewed the plastic thingie on the outside to unscrew the old video card. Because of the stupid arrangement of the ports, I had to unscrew the motherboard to unplug it. So I unscrewed it, removed the old card, put in the new one, moved the motherboard back, screwed it back in, screwed the video card on the holder... thingie, and screwed the plastic thingie back in. Everything went smoothly, nothing had to be forced in/out. I connected the external power supply, closed the computer case, put the tower back in it's place and all the cables back in. When I pressed the power button, the LED turned... some color I can't distinguish. It stayed that way for a second, and then it went off. I tried a bunch of things, including permuting the external power supply arrangement (1 connection, 2 connections and no connections), with no success. And here are some of the specifications: Motherboard manufacturer: Asrock Processor: AMD Athlon II X2 3.0 GHz RAM: 2 x 2GB (had only 1 initially, bought the second plate a bit later) OLD video card: AMD Radeon HD 5450 NEW video card: Gigabyte nVidia GeForce GTX 650 GPU, 1GB GDDR5 128bit PCI-E, Dual-link DVI-Dx2 / HDMI / D-Sub Power supply: 450W + all the requirements I managed to find on the internet are met (+12V 18A or something) More specific information is stored... On that computer. If required, I may open the case again and read the stickers to find more specific information. I can also provide photos if necessary. Any ideas? Suggestions? Something? :|

  Read the article

• How does rsync --daemon know which way it is being run?

  - by Skaperen

  I am wanting to run rsync over an SSL/TLS encrypted connection. It does not do this directly so I am exploring options. The stunnel program looks promising, although more complicated than designed due to the need to hop connections with the -r option. However, I do find there is a -l option to run a program. I am assuming this works by having two processes, one to carry out the SSL/TLS work, and one to be the worker which the client is communicating to. These would then communicate by a pipe pair or two way socket between them. What struck me as odd when I surveyed a number of web pages to see how to properly set this up is that whether running as a standalone daemon, or under a super daemon like inetd, the arguments for rsync are the same. How does rsync --daemon know whether it should open a socket and listen on it for many connections, or just service one connection by communicating with the stdin/stdout descriptors is has when it starts up (which really would go through the extra process to handle the encryption, description, and SSL/TLS protocol layer)? And then I need to find a way to wrap the client to have it do SSL/TLS in one simple command (as opposed to connection hopping that stunnel seems to favor).

  Read the article

• Why is my server performance degrading to the point of stopping, periodically?

  - by Pascal Aschwanden

  So, once in a while, I see in firebug that a request takes over 15 or even 60 seconds to respond and sometimes never. Here is what I've ruled out: It's not the CPU, cuz every time I check the Server load its less then 6 for all 3 numbers It's not the memory, because thats fairly low too, less the 50% It's not the I/O anymore, because I've seen the graphs that Joyent sent back to me when I requested them, and they show less then 3MB of I/O (mostly all read). It's not the SQL performance - I've profiled every last SQL command that runs, and they're all (99.9% of them anyway) running in less then 30ms, most run in less then 5ms. Oh and I've been profiling all the script execution times, and even the when the problem occurs, the script always manages to finish in 50ms or less (that's 1 / 20th of a second ). Now, I do run alot of ajax calls. 1 every 2 seconds per user and I have 300 DAU+. But, even if all 300 are playing simultaneously, thats still only 150 calls per second max. The only other thing I can think of is that one of my neighbors is funky. The problem is highly intermittent. 99% of the time it works perfectly and there's excellent performance. but 99%+ is not good enough. Eventually the performance gets so bad I have to restart the server, at which point everything is fine again. I've done this about 4 times now. Any ideas? Note: this is on joyent, vps, intro package 256mb of ram with bursting. here are the mysql dump info: Traffic ø per hour Received 18 MiB 29 MiB Sent 134 MiB 221 MiB Total 151 MiB 251 MiB Connections ø per hour % max. concurrent connections 5 --- --- Failed attempts 0 0.00 0.00% Aborted 0 0.00 0.00% Total 9,418 15.59 k 100.00%

  Read the article

• MysqlTunner and query_cache_size dilemma

  - by wbad

  On a busy mysql server MySQLTuner 1.2.0 always recommends to add query_cache_size no matter how I increase the value (I tried up to 512MB). On the other hand it warns that : Increasing the query_cache size over 128M may reduce performance Here are the last results: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.25-1~dotdeb.0-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 6G (Tables: 195) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 51 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 19h 17m 8s (254M q [1K qps], 5M conn, TX: 139B, RX: 32B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 24.2G global + 92.2M per thread (1200 max threads) [!!] Maximum possible memory usage: 132.2G (139% of installed RAM) [OK] Slow queries: 0% (2K/254M) [OK] Highest usage of available connections: 32% (391/1200) [OK] Key buffer size / total MyISAM indexes: 128.0M/92.0K [OK] Key buffer hit rate: 100.0% (8B cached / 0 reads) [OK] Query cache efficiency: 79.9% (181M cached / 226M selects) [!!] Query cache prunes per day: 1033203 [OK] Sorts requiring temporary tables: 0% (341 temp sorts / 4M sorts) [OK] Temporary tables created on disk: 14% (760K on disk / 5M total) [OK] Thread cache hit rate: 99% (676 created / 5M connections) [OK] Table cache hit rate: 22% (1K open / 8K opened) [OK] Open file limit used: 0% (49/13K) [OK] Table locks acquired immediately: 99% (64M immediate / 64M locks) [OK] InnoDB data size / buffer pool: 6.1G/19.5G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 192M) [see warning above] The server has 76GB ram and dual E5-2650. The load is usually below 2. I appreciate your hints to interpret the recommendation and optimize the database configs.

  Read the article

• System With Two Network Adapters [closed]

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• No access to Windows 2003 admin shares

  - by ARomo

  This is the environment: Several Win 2003 SP 2 servers and several Win XP SP2 & SP3 clients. All in the same LAN. Firewall is disabled everywhere. No recent Windows updates or configuration changes. This is the problem: Since last Thursday, I log on to any other server or workstation as any regular (non-admin) user and I fail to be able to open ADMIN SHARES ONLY (namely \\server1\c$, \\server1\e$ and \\server1\admin$). The error message is: "\server1\c$ is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Multiple connections to a server or shared resource by the same user, using more than one user name, are not allowed. Disconnect all previous connections to the server or shared resource and try again." I can, however, open the same shares if I use FQDN or IP address: \\server1.domain.local\c$ \\172.0.0.1\c$ Other shares do not have this issue and I can open them without any issue. Any ideas or suggestion would be truly appreciated. Thank you in advance.

  Read the article

• How do I automatically connect my client to an ODBC data source on another machine with dynamic IP?

  - by Kdansky

  At the customer's place, we've got a postgres DB on a server, and a few clients. We connect them through ODBC-drivers, and all machines run windows (usually XP). Now we had a few annoying issues: The client "forgets" some flags in the ODBC drivers, such as ByteA as LO. Every time anything changes, we have to reset that, and type in the password, and sometimes even the IP of the server. On x64 machines running Windows 7, configuring this is a pain as the system settings dialogue will only show 64-bit connections by default. And most importantly: If the server changes IP because the customer restarts or replaces a switch, all connections are lost. Annoyingly, this cannot be fixed with just correcting the IP, but rather, we have to check every single place (even hba_conf) because all the settings magically disappear. Our customers often are very small companies, where "server" means "that one PC in the other room", and not "Oracle mainframe in the dungeon", so we don't want to rely on them not restarting switches. Is there a better way than to rely on these really unstable settings? Are these settings somewhere in a file which I could edit manually, to make fixing it easier?

  Read the article

• Are there any other causes of this error that are NOT related to initial setup?

  - by LordScree

  I'm trying to diagnose an issue at a customer site. They are receiving the following error: A network-related or instance-specific error occurred while establishing a connection to SQL Server I've seen this a few times, but only during the initial setup - it's often caused by one of the following: The database server is turned off The network connection between the database server and the application is closed or somehow blocked (e.g. a firewall) The SQL Server instance is not set up to receive remote connections from the application server (e.g. TCP is turned off, remote connections are disabled, or the "SQL Server Browser" service is stopped/disabled) However, if I assume that no configuration changes have been made, I'm trying to postulate on what the reason might be for getting this error at a random point after the initial setup. My initial thought is: SQL Server machine has run out of resources (e.g. RAM) and is unable to accept new requests from the application server Is this a valid theory? What other possible causes are there of this error that are not related to the initial setup of the server / application connection? Or is it simply impossible that this error could occur without a configuration change having been made (either on the SQL Server side, application side, or somewhere in-between (network))? NOTE: I believe this question differs from the plethora of questions related to this error message because the application and server have been talking to each other quite happily until now (most, if not all, other questions seem to relate to initial setup).

  Read the article

• How do I speed up and cache mmap file access over NFS on Linux?

  - by Zan Lynx

  The server and client are both 64-bit Ubuntu 10.04 LTS. The application in question is a custom app that uses mmap() for fast random file access. Its ideal state is when the entire file is cached in RAM. The network connections are really fast 10Gb Ethernet. It is a virtual server blade setup. It isn't the network connections slowing things down because everything performs superbly when using a virtual disk (iSCSI to the SAN). But when we run the application on a NFS home directory mount, performance goes to the dogs. It appears that the Linux kernel isn't caching anything. So it is reading every single disk block needed by mmap() accesses over and over and over again. The NFS mount is done through autofs, which has only default settings. /proc/mounts shows the NFS mount is done with the following options: rw,relatime,vers=3,rsize=131072,wsize=131072,namlen=255,hard,proto=tcp,timeo=600,retrans=2,sec=sys,mountaddr=192.168.11.52,mountvers=3,mountproto=tcp,addr=192.168.11.52 How can I make Ubuntu 10.04 cache the file instead of reloading it all the time?

  Read the article

• Log Problem and bash script

  - by GvWorker

  Hello Guys, I have 11 Debian servers running on rackspace cloud hosting. All running VHCS2 for hosting management. 1 server is used for application and 10 are used for only smtp. My question is regarding smtp servers. Each server hosted 1 domain. My problem is when my client use smtp there's a log created in this directory /var/log/ but within 24 hours drives are full and server refuse all smtp connections. Then I deleted the logs and ran following command to check the disk space. df -h but it shows hdd still full and server is still refusing the smtp connections. Then I ran following command to see the truth du --max-depth=1 -h It shows the truth. The real disk space used. Then I rebooted the server and now server working fine. But after few hours same situation happened. Then I created the following script. #!/bin/sh rm -fr /var/log/* rm -fr /var/log/apache2/*.log rm -fr /var/log/apache2/*.log.* rm -fr /var/log/apache2/users/* rm -fr /var/log/apache2/backup/* reboot It worked for days but after that logs are again filling the hdd. Now I want the following solutions. If anybody can help me. When I delete files from server hdd will free up without rebooting Log should be in specific range. Like a specific size of file where old data overwrite with new data

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >