Search Results

Search found 1776 results on 72 pages for 'story'.

Page 67/72 | < Previous Page | 63 64 65 66 67 68 69 70 71 72  | Next Page >

• Confirm disk is broken when it passes all diagnostics

  - by Halfgaar

  I have a system with a potentially broken disk, but the disk passes all manner of diagnostics. I have been unable to confirm that the disk is broken. What are my options? I could just replace the disk, but because this situation is very similar to another more severe situation I have (long story), I'd like to actually make a proper diagnosis as opposed to randomly binning hardware. The issue and history is this: I had a Debian Linux PC (500 MHz P3) acting as router, nagios and munin. It crashed every couple of weeks. No logs or dmesg could be obtained (because it's an old Compaq that only boots when you configure it as keyboardless, making connecting a keyboard later, once it's booted, impossible). At the time, I just replaced the computer with another Compaq (P4 2.4 GHz) because I thought the hardware was faulty. However, it still crashed every couple of weeks. the difference is that on this computer, I can still SSH into it. It gives all kinds of errors on hda. I'd like to confirm that the disk is broken, but nothing I do confirms this: SMART error logs shows no errors. Normally when a disk starts acting up, SMART my pass, but it still records a read-error in the error log. SMART self-test (smartctl -t long /dev/sda) completes without errors. re-allocated sector count (a tell-tale parameter) has been 31 all its life, even when the disk was still in use in my desktop PC years ago, and it still is. The figure never changed. dd if=/dev/sda of=/dev/null bs=4096 passes with flying colors. What else can I do to assess the health of the drive? Again, this is not about making this router fully functional again, this is a disk forensic question, because it just so happens that I have another server that potentially has the same problem, and knowing the answer to this will possibly help me greatly. For the record, below are logs and such. This is the smartctl -a output: smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family Device Model: ST3120026A Serial Number: 5JT1CLQM Firmware Version: 3.06 User Capacity: 120,034,123,776 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 Local Time is: Mon Jul 1 21:18:33 2013 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 24) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 050 046 006 Pre-fail Always - 47766662 3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 10 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 31 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 820305 9 Power_On_Hours 0x0032 048 048 000 Old_age Always - 46373 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 605 194 Temperature_Celsius 0x0022 036 065 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x001a 050 046 000 Old_age Always - 47766662 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 196 000 Old_age Always - 6 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 80% 46361 - # 2 Extended offline Completed without error 00% 46358 - # 3 Short offline Completed without error 00% 12046 - # 4 Extended offline Completed without error 00% 10472 - # 5 Short offline Completed without error 00% 10471 - # 6 Short offline Completed without error 00% 10471 - # 7 Short offline Completed without error 00% 6770 - # 8 Extended offline Aborted by host 90% 5958 - # 9 Extended offline Aborted by host 90% 5951 - #10 Short offline Completed without error 00% 5024 - #11 Extended offline Aborted by host 80% 5024 - #12 Short offline Completed without error 00% 3697 - #13 Short offline Completed without error 00% 237 - #14 Short offline Completed without error 00% 145 - #15 Short offline Completed without error 00% 69 - #16 Extended offline Completed without error 00% 68 - #17 Short offline Completed without error 00% 66 - #18 Short offline Completed without error 00% 49 - #19 Short offline Completed without error 00% 29 - #20 Short offline Completed without error 00% 29 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. And this is the dmesg error when it has crashed (which repeats for a bunch of different sectors): [1755091.211136] sd 0:0:0:0: [sda] Unhandled error code [1755091.211144] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1755091.211151] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 08 fe ad 38 00 00 08 00 [1755091.211166] end_request: I/O error, dev sda, sector 150908216

  Read the article

• Mount TMPFS instead of ro /dev

  - by schiggn

  I am working on a ARM-Based embedded system with a custom Debian Linux based on kernel 2.6.31. In the final system, the Root file system is stored as squashfs on flash. Now, the folder /dev is created by udev, but since there is no hot plugging functionality needed and booting time is critical, I wanted to delete udev and "hard code" the /dev folder (read here, page 5). because i still need to change parameters of the devices (with ioctl /sysfs) this does not work for me in this case. so i thought of mounting a tmpfs on /dev and change the parameters there. is this possible? and how to do best? my approach would be: delete /dev from RFS create tar containing basic devices mount tmpfs /dev untar tar-file into /dev change parameters Could this work? Do you see any problems? I found out, that you can mount on top of already mounted mount point, is it somehow possible just to take data with while mounting the new file system? if so that would be very convenient! Thanks Update: I just tried that out, but I'm stuck at a certain point. I packed all my devices into devices.tar, packed it into /usr of my squashfs and added the following lines to mountkernfs.sh, which is executed right after INIT. #mount /dev on tmpfs echo -n "Mounting /dev on tmpfs..." mount -o size=5M,mode=0755 -t tmpfs tmpfs /dev mknod -m 600 /dev/console c 5 1 mknod -m 600 /dev/null c 1 3 echo "done." echo -n "Populating /dev..." tar -xf /usr/devices.tar -C /dev echo "done." This works fine on the version over NFS, if I place printf's in the code, I can see it executing, if I comment out the extracting part, its complaining about missing devices. Booting OK mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. System Clock set to: Thu Sep 13 11:26:23 UTC 2012. INIT: Entering runlevel: 2 UBI: attaching mtd8 to ubi0 Commenting out the extraction of the tar mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Thu Sep 13 12:24:00 UTC 2012 ... (warning). INIT: Entering runlevel: 2 libubi: error!: cannot open "/dev/ubi_ctrl" So far so good. But if I pack the whole story into a squashfs and boot from there, it is acting strange. It's telling me while booting that it is unable to open an initial console and its throwing errors on mounting the UBIFS devices, but finally provides a login anyway. Over that my echo's are not executed. If I then log in, /dev is mounted as TMPFS as desired and all the devices reside inside. When I redo the "mount" command to mount the UBIFS partitions it is executed whitout problem and useable. From squashfs VFS: Mounted root (squashfs filesystem) readonly on device 31:15. Freeing init memory: 136K Warning: unable to open an initial console. mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 UBIFS error (pid 484): ubifs_get_sb: cannot open "ubi1_0", error -19 Additionally, a part of the rest of the bootscripts is still exexuted, but not all of them. Does anyone has a clue why? Other question, is 5MB enough/too much for /dev?

  Read the article

• Wireshark does not see interfaces (winXP)

  - by bua

  Short story: Wireshark is working....on my winXP-32b ... usage .... Long long time later Wireshark does not work It can't find any usefull interface (just VPN) ipconfig /all Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1490 Dual Band WLAN Mini-Card Physical Address. . . . . . . . . : SOME VALID MAC Ethernet adapter eth0: Connection-specific DNS Suffix . : xxxx Description . . . . . . . . . . . : Broadcom 440x 10/100 Integrated Controller Physical Address. . . . . . . . . : SOME VALID MAC Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.12.68 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168..... ..... Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Fortinet virtual adapter Physical Address. . . . . . . . . : SOME VALID MAC Following steps didn't help: Several Wireshark re-installation Several LIBPCAP re installation SP3 for winXP Any ideas welcome.

  Read the article

• Paying great programmers more than average programmers

  - by Kelly French

  It's fairly well recognized that some programmers are up to 10 times more productive than others. Joel mentions this topic on his blog. There is a whole blog devoted to the idea of the "10x productive programmer". In years since the original study, the general finding that "There are order-of-magnitude differences among programmers" has been confirmed by many other studies of professional programmers (Curtis 1981, Mills 1983, DeMarco and Lister 1985, Curtis et al. 1986, Card 1987, Boehm and Papaccio 1988, Valett and McGarry 1989, Boehm et al 2000). Fred Brooks mentions the wide range in the quality of designers in his "No Silver Bullet" article, The differences are not minor--they are rather like the differences between Salieri and Mozart. Study after study shows that the very best designers produce structures that are faster, smaller, simpler, cleaner, and produced with less effort. The differences between the great and the average approach an order of magnitude. The study that Brooks cites is: H. Sackman, W.J. Erikson, and E.E. Grant, "Exploratory Experimental Studies Comparing Online and Offline Programming Performance," Communications of the ACM, Vol. 11, No. 1 (January 1968), pp. 3-11. The way programmers are paid by employers these days makes it almost impossible to pay the great programmers a large multiple of what the entry-level salary is. When the starting salary for a just-graduated entry-level programmer, we'll call him Asok (From Dilbert), is $40K, even if the top programmer, we'll call him Linus, makes $120K that is only a multiple of 3. I'd be willing to be that Linus does much more than 3 times what Asok does, so why wouldn't we expect him to get paid more as well? Here is a quote from Stroustrup: "The companies are complaining because they are hurting. They can't produce quality products as cheaply, as reliably, and as quickly as they would like. They correctly see a shortage of good developers as a part of the problem. What they generally don't see is that inserting a good developer into a culture designed to constrain semi-skilled programmers from doing harm is pointless because the rules/culture will constrain the new developer from doing anything significantly new and better." This leads to two questions. I'm excluding self-employed programmers and contractors. If you disagree that's fine but please include your rationale. It might be that the self-employed or contract programmers are where you find the top-10 earners, but please provide a explanation/story/rationale along with any anecdotes. [EDIT] I thought up some other areas in which talent/ability affects pay. Financial traders (commodities, stock, derivatives, etc.) designers (fashion, interior decorators, architects, etc.) professionals (doctor, lawyer, accountant, etc.) sales Questions: Why aren't the top 1% of programmers paid like A-list movie stars? What would the industry be like if we did pay the "Smart and gets things done" programmers 6, 8, or 10 times what an intern makes? [Footnote: I posted this question after submitting it to the Stackoverflow podcast. It was included in episode 77 and I've written more about it as a Codewright's Tale post 'Of Rockstars and Bricklayers'] Epilogue: It's probably unfair to exclude contractors and the self-employed. One aspect of the highest earners in other fields is that they are free-agents. The competition for their skills is what drives up their earning power. This means they can not be interchangeable or otherwise treated as a plug-and-play resource. I liked the example in one answer of a major league baseball team trying to field two first-basemen. Also, something that Joel mentioned in the Stackoverflow podcast (#77). There are natural dynamics to shrink any extreme performance/pay ranges between the highs and lows. One is the peer pressure of organizations to pay within a given range, another is the likelyhood that the high performer will realize their undercompensation and seek greener pastures.

  Read the article

• Python: how do I install SciPy on 64 bit Windows?

  - by Peter Mortensen

  How do I install SciPy on my system? Update 1: for the NumPy part (that SciPy depends on) there is actually an installer for 64 bit Windows: numpy-1.3.0.win-amd64-py2.6.msi (is direct download URL, 2310144 bytes). Running the SciPy superpack installer results in this message in a dialog box: "Cannot install. Python version 2.6 required, which was not found in the registry." I already have Python 2.6.2 installed (and a working Django installation in it), but I don't know about any Registry story. The registry entries seems to already exist: REGEDIT4 [HKEY_LOCAL_MACHINE\SOFTWARE\Python] [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore] [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore\2.6] [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore\2.6\Help] [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore\2.6\Help\Main Python Documentation] @="D:\\Python262\\Doc\\python262.chm" [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore\2.6\InstallPath] @="D:\\Python262\\" [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore\2.6\InstallPath\InstallGroup] @="Python 2.6" [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore\2.6\Modules] [HKEY_LOCAL_MACHINE\SOFTWARE\Python\PythonCore\2.6\PythonPath] @="D:\\Python262\\Lib;D:\\Python262\\DLLs;D:\\Python262\\Lib\\lib-tk" What I have done so far: Step 1 Downloaded the NumPy superpack installer numpy-1.3.0rc2-win32-superpack-python2.6.exe (direct download URL, 4782592 bytes). Running this installer resulted in the same message, "Cannot install. Python version 2.6 required, which was not found in the registry.". Update: there is actually an installer for NumPy that works - see beginning of the question. Step 2 Tried to install NumPy in another way. Downloaded the zip package numpy-1.3.0rc2.zip (direct download URL, 2404011 bytes), extracted the zip file in a normal way to a temporary directory, D:\temp7\numpy-1.3.0rc2 (where setup.py and README.txt is). I then opened a command line window and: d: cd D:\temp7\numpy-1.3.0rc2 setup.py install This ran for a long time and also included use of cl.exe (part of Visual Studio). Here is a nearly 5000 lines long transcript (230 KB). This seemed to work. I can now do this in Python: import numpy as np np.random.random(10) with this result: array([ 0.35667511, 0.56099423, 0.38423629, 0.09733172, 0.81560421, 0.18813222, 0.10566666, 0.84968066, 0.79472597, 0.30997724]) Step 3 Downloaded the SciPy superpack installer, scipy-0.7.1rc3- win32-superpack-python2.6.exe (direct download URL, 45597175 bytes). Running this installer resulted in the message listed in the beginning Step 4 Tried to install SciPy in another way. Downloaded the zip package scipy-0.7.1rc3.zip (direct download URL, 5506562 bytes), extracted the zip file in a normal way to a temporary directory, D:\temp7\scipy-0.7.1 (where setup.py and README.txt is). I then opened a command line window and: d: cd D:\temp7\scipy-0.7.1 setup.py install This did not achieve much - here is a transcript (about 95 lines). And it fails: >>> import scipy as sp2 Traceback (most recent call last): File "<stdin>", line 1, in <module> ImportError: No module named scipy Platform: Python 2.6.2 installed in directory D:\Python262, Windows XP 64 bit SP2, 8 GB RAM, Visual Studio 2008 Professional Edition installed. The startup screen of the installed Python is: Python 2.6.2 (r262:71605, Apr 14 2009, 22:46:50) [MSC v.1500 64 bit (AMD64)] on win32 Type "help", "copyright", "credits" or "license" for more information. >>> Value of PATH, result from SET in a command line window: Path=D:\Perl64\site\bin;D:\Perl64\bin;C:\Program Files (x86)\PC Connectivity Solution\;D:\Perl\site\bin;D:\Perl\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static;d:\Program Files (x86)\WinSCP\;D:\MassLynx\;D:\Program Files (x86)\Analyst\bin;d:\Python262;d:\Python262\Scripts;D:\Program Files (x86)\TortoiseSVN\bin;D:\Program Files\TortoiseSVN\bin;C:\WINDOWS\system32\WindowsPowerShell\v1.0;D:\Program Files (x86)\IDM Computer Solutions\UltraEdit\

  Read the article

• Trouble determining proper decoding of a REST response from an ArcGIS REST service using IHttpModule

  - by Ryan Taylor

  First a little background on what I am trying to achieve. I have an application that is utilizing REST services served by ArcGIS Server and IIS7. The REST services return data in one of several different formats. I am requesting a JSON response. I want to be able to modify the response (remove or add parameters) before the response is sent to the client. However, I am having difficulty converting the stream to a string that I can modify. To that end, I have implemented the following code in order to try to inspect the stream. SecureModule.cs using System; using System.Web; namespace SecureModuleTest { public class SecureModule : IHttpModule { public void Init(HttpApplication context) { context.BeginRequest += new EventHandler(OnBeginRequest); } public void Dispose() { } public void OnBeginRequest(object sender, EventArgs e) { HttpApplication application = (HttpApplication) sender; HttpContext context = application.Context; HttpRequest request = context.Request; HttpResponse response = context.Response; response.Filter = new ServicesFilter(response.Filter); } } } ServicesFilter.cs using System; using System.IO; using System.Text; namespace SecureModuleTest { class ServicesFilter : MemoryStream { private readonly Stream _outputStream; private StringBuilder _content; public ServicesFilter(Stream output) { _outputStream = output; _content = new StringBuilder(); } public override void Write(byte[] buffer, int offset, int count) { _content.Append(Encoding.UTF8.GetString(buffer, offset, count)); using (TextWriter textWriter = new StreamWriter(@"C:\temp\content.txt", true)) { textWriter.WriteLine(String.Format("Buffer: {0}", _content.ToString())); textWriter.WriteLine(String.Format("Length: {0}", buffer.Length)); textWriter.WriteLine(String.Format("Offset: {0}", offset)); textWriter.WriteLine(String.Format("Count: {0}", count)); textWriter.WriteLine(""); textWriter.Close(); } // Modify response _outputStream.Write(buffer, offset, count); } } } The module is installed in the /ArcGIS/rest/ virtual directory and is executed via the following GET request. http://localhost/ArcGIS/rest/services/?f=json&pretty=true The web page displays the expected response, however, the text file tells a very different (encoded?) story. Expect Response {"currentVersion" : "10.0", "folders" : [], "services" : [ ] } Text File Contents Buffer: ? ?`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q? Length: 4096 Offset: 0 Count: 168 Buffer: ? ?`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q?K???!P Length: 4096 Offset: 0 Count: 11 Interestingly, Fiddler depicts a similar picture. Fiddler Request GET http://localhost/ArcGIS/rest/services/?f=json&pretty=true HTTP/1.1 Host: localhost Connection: keep-alive User-Agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.70 Safari/533.4 Referer: http://localhost/ArcGIS/rest/services Cache-Control: no-cache Pragma: no-cache Accept: application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Cookie: a=mWz_JFOusuGPnS3w5xx1BSUuyKGB3YZo92Dy2SUntP2MFWa8MaVq6a4I_IYBLKuefXDZANQMeqvxdGBgQoqTKz__V5EQLHwxmKlUNsaK7do. Fiddler Response - Before Clicking Decode HTTP/1.1 200 OK Content-Type: text/plain;charset=utf-8 Content-Encoding: gzip ETag: 719143506 Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Thu, 10 Jun 2010 01:08:43 GMT Content-Length: 179 ????????`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q?K???! P??? Fiddler Response - After Clicking Decode HTTP/1.1 200 OK Content-Type: text/plain;charset=utf-8 ETag: 719143506 Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Thu, 10 Jun 2010 01:08:43 GMT Content-Length: 80 {"currentVersion" : "10.0", "folders" : [], "services" : [ ] } I think that the problem may be a result of compression and/or chunking of data (this might be why I am receiving two calls to ServicesFilter.Write(...), however, I have not yet been able to solve the issue. How might I decode, unzip, and otherwise convert the byte stream into the string I know it should be for modification by my filter?

  Read the article

• Streaming a webcam from Silverlight 4 (Beta)

  - by Ken Smith

  The new webcam stuff in Silverlight 4 is darned cool. By exposing it as a brush, it allows scenarios that are way beyond anything that Flash has. At the same time, accessing the webcam locally seems like it's only half the story. Nobody buys a webcam so they can take pictures of themselves and make funny faces out of them. They buy a webcam because they want other people to see the resulting video stream, i.e., they want to stream that video out to the Internet, a lay Skype or any of the dozens of other video chat sites/applications. And so far, I haven't figured out how to do that with It turns out that it's pretty simple to get a hold of the raw (Format32bppArgb formatted) bytestream, as demonstrated here. But unless we want to transmit that raw bytestream to a server (which would chew up way too much bandwidth), we need to encode that in some fashion. And that's more complicated. MS has implemented several codecs in Silverlight, but so far as I can tell, they're all focused on decoding a video stream, not encoding it in the first place. And that's apart from the fact that I can't figure out how to get direct access to, say, the H.264 codec in the first place. There are a ton of open-source codecs (for instance, in the ffmpeg project here), but they're all written in C, and they don't look easy to port to C#. Unless translating 10000+ lines of code that look like this is your idea of fun :-) const int b_xy= h->mb2b_xy[left_xy[i]] + 3; const int b8_xy= h->mb2b8_xy[left_xy[i]] + 1; *(uint32_t*)h->mv_cache[list][cache_idx ]= *(uint32_t*)s->current_picture.motion_val[list][b_xy + h->b_stride*left_block[0+i*2]]; *(uint32_t*)h->mv_cache[list][cache_idx+8]= *(uint32_t*)s->current_picture.motion_val[list][b_xy + h->b_stride*left_block[1+i*2]]; h->ref_cache[list][cache_idx ]= s->current_picture.ref_index[list][b8_xy + h->b8_stride*(left_block[0+i*2]>>1)]; h->ref_cache[list][cache_idx+8]= s->current_picture.ref_index[list][b8_xy + h->b8_stride*(left_block[1+i*2]>>1)]; The mooncodecs folder within the Mono project (here) has several audio codecs in C# (ADPCM and Ogg Vorbis), and one video codec (Dirac), but they all seem to implement just the decode portion of their respective formats, as do the java implementations from which they were ported. I found a C# codec for Ogg Theora (csTheora, http://www.wreckedgames.com/forum/index.php?topic=1053.0), but again, it's decode only, as is the jheora codec on which it's based. Of course, it would presumably be easier to port a codec from Java than from C or C++, but the only java video codecs that I found were decode-only (such as jheora, or jirac). So I'm kinda back at square one. It looks like our options for hooking up a webcam (or microphone) through Silverlight to the Internet are: (1) Wait for Microsoft to provide some guidance on this; (2) Spend the brain cycles porting one of the C or C++ codecs over to Silverlight-compatible C#; (3) Send the raw, uncompressed bytestream up to a server (or perhaps compressed slightly with something like zlib), and then encode it server-side; or (4) Wait for someone smarter than me to figure this out and provide a solution. Does anybody else have any better guidance? Have I missed something that's just blindingly obvious to everyone else? (For instance, does Silverlight 4 somewhere have some classes I've missed that take care of this?)

  Read the article

• How to pre-load all deployed assemblies for an AppDomain

  - by Andras Zoltan

  Given an App Domain, there are many different locations that Fusion (the .Net assembly loader) will probe for a given assembly. Obviously, we take this functionality for granted and, since the probing appears to be embedded within the .Net runtime (Assembly._nLoad internal method seems to be the entry-point when Reflect-Loading - and I assume that implicit loading is probably covered by the same underlying algorithm), as developers we don't seem to be able to gain access to those search paths. My problem is that I have a component that does a lot of dynamic type resolution, and which needs to be able to ensure that all user-deployed assemblies for a given AppDomain are pre-loaded before it starts its work. Yes, it slows down startup - but the benefits we get from this component totally outweight this. The basic loading algorithm I've already written is as follows. It deep-scans a set of folders for any .dll (.exes are being excluded at the moment), and uses Assembly.LoadFrom to load the dll if it's AssemblyName cannot be found in the set of assemblies already loaded into the AppDomain (this is implemented inefficiently, but it can be optimized later): void PreLoad(IEnumerable<string> paths) { foreach(path p in paths) { PreLoad(p); } } void PreLoad(string p) { //all try/catch blocks are elided for brevity string[] files = null; files = Directory.GetFiles(p, "*.dll", SearchOption.AllDirectories); AssemblyName a = null; foreach (var s in files) { a = AssemblyName.GetAssemblyName(s); if (!AppDomain.CurrentDomain.GetAssemblies().Any( assembly => AssemblyName.ReferenceMatchesDefinition( assembly.GetName(), a))) Assembly.LoadFrom(s); } } LoadFrom is used because I've found that using Load() can lead to duplicate assemblies being loaded by Fusion if, when it probes for it, it doesn't find one loaded from where it expects to find it. So, with this in place, all I now have to do is to get a list in precedence order (highest to lowest) of the search paths that Fusion is going to be using when it searches for an assembly. Then I can simply iterate through them. The GAC is irrelevant for this, and I'm not interested in any environment-driven fixed paths that Fusion might use - only those paths that can be gleaned from the AppDomain which contain assemblies expressly deployed for the app. My first iteration of this simply used AppDomain.BaseDirectory. This works for services, form apps and console apps. It doesn't work for an Asp.Net website, however, since there are at least two main locations - the AppDomain.DynamicDirectory (where Asp.Net places it's dynamically generated page classes and any assemblies that the Aspx page code references), and then the site's Bin folder - which can be discovered from the AppDomain.SetupInformation.PrivateBinPath property. So I now have working code for the most basic types of apps now (Sql Server-hosted AppDomains are another story since the filesystem is virtualised) - but I came across an interesting issue a couple of days ago where this code simply doesn't work: the nUnit test runner. This uses both Shadow Copying (so my algorithm would need to be discovering and loading them from the shadow-copy drop folder, not from the bin folder) and it sets up the PrivateBinPath as being relative to the base directory. And of course there are loads of other hosting scenarios that I probably haven't considered; but which must be valid because otherwise Fusion would choke on loading the assemblies. I want to stop feeling around and introducing hack upon hack to accommodate these new scenarios as they crop up - what I want is, given an AppDomain and its setup information, the ability to produce this list of Folders that I should scan in order to pick up all the DLLs that are going to be loaded; regardless of how the AppDomain is setup. If Fusion can see them as all the same, then so should my code. Of course, I might have to alter the algorithm if .Net changes its internals - that's just a cross I'll have to bear. Equally, I'm happy to consider SQL Server and any other similar environments as edge-cases that remain unsupported for now. Any ideas!?

  Read the article

• Search engine solution for Django that actually works?

  - by prometheus

  The story so far: Decided to go with Xapian as search backend because it has all search-engine features I was looking for, knows about Unicode, stemming, has few dependencies and requires no bloated app-server installation on top of it. Tried Django and Haystack (plus xapian-haystack, the backend glue code to tie Haystack to Xapian) because it was advertised on quite some blogs as "working". Did not work. Neither django-haystack nor the xapian-haystack project provide a version combination that actually works together. MASTER from both projects yields an error from Xapian, so it's not stable at all. Haystack 1.0.1 and xapian-haystack 1.0.x/1.1.0 are not API-compatible. Plus, in a minimally working installation of Haystack 1.0.1 and xapian-haystack MASTER, any complex query yields zero results due to errors in either django-haystack or xapian-haystack (I double-verified this), maybe because the unit-tests actually test very simple cases, and no edge-cases at all. Tried Djapian. The source-code is riddled with spelling errors (mind you, in variable names, not comments), documentation is also riddled with ambiguities and outdated information that will never lead to a working installation. Not surprisingly, users rarely ask for features but how to get it working in the first place. Next on the plate: exploring Solr (installing a Java environment plus Tomcat gives me headaches, the machine is RAM- and CPU-constrained), or Lucene (slightly less headaches, but still). Before I proceed spending more time with a solution that might or might not work as advertised, I'd like to know: Did anyone ever get an actual, real-world search solution working in Django? I'm serious. I find it really frustrating reading about "large problems mostly solved", and then realizing that you will never get a working installation from the source-code because, actually, all bloggers dealing with those "mostly solved problems" never went past basic installation and copy-pasting the official tutorials. So here are the requirements: must be able to search for 10-100 terms in one query must handle + (term must be present) and - (term must not be present), AND/OR must handle arbitrary grouping (i.e. parentheses around AND/OR) must allow for Django-ORM filtering before or after fulltext-search (i.e. pre-/post-processing of results with the full set of filters that Django knows about) alternatively, there must be a facility to bulk-fetch the result set and transform it into a QuerySet should be light on the machine, so preferably no humongous JVM and Java-based app-server installation Is there anything out there that does this? I'm not interested in anecdotal evidence, or references to some blog posts that claim it should be working. I'd like to hear from someone who actually has a fully-functional setup working in the real world, under real conditions, with real queries. EDIT: Let me repeat again that I'm not so much interested in anecdotal evidence that someone, somewhere has a somewhat running installation working with unspecified properties. I already went there, I read all the blog posts, mailing lists, I contacted the authors, but when it came to actual implementation of real-world scenarios, nothing ever worked as advertised. Also, and a user below brought that point up as well, considering the TCO of any project, I'm definitely not interested in hearing that someone, somewhere was able to pull it off once a vendor parachuted in an unknown number of specialists to monkey-patch the whole installation with specific domain-knowledge that's documented nowhere. So, please, if you claim you have a working installation that actually satisfies minimum requirements for a full-fledged search (see requirements above), please provide the following so that we can all benefit from a search solution for Django that actually solves the problem: exact Linux distribution, release version, exact release version of Haystack (or equivalent) and release version of search backend, exact release version of the search engine publicly (!) available documentation how to set up all components exactly in the way that your installation was set up such that the minimal requirements above are met. Thank you.

  Read the article

• Search engine solution for Django that actually works?

  - by prometheus

  The story so far: Decided to go with Xapian as search backend because it has all search-engine features I was looking for, knows about Unicode, stemming, has few dependencies and requires no bloated app-server installation on top of it. Tried Django and Haystack (plus xapian-haystack, the backend glue code to tie Haystack to Xapian) because it was advertised on quite some blogs as "working". Did not work. Neither django-haystack nor the xapian-haystack project provide a version combination that actually works together. MASTER from both projects yields an error from Xapian, so it's not stable at all. Haystack 1.0.1 and xapian-haystack 1.0.x/1.1.0 are not API-compatible. Plus, in a minimally working installation of Haystack 1.0.1 and xapian-haystack MASTER, any complex query yields zero results due to errors in either django-haystack or xapian-haystack (I double-verified this), maybe because the unit-tests actually test very simple cases, and no edge-cases at all. Tried Djapian. The source-code is riddled with spelling errors (mind you, in variable names, not comments), documentation is also riddled with ambiguities and outdated information that will never lead to a working installation. Not surprisingly, users rarely ask for features but how to get it working in the first place. Next on the plate: exploring Solr (installing a Java environment plus Tomcat gives me headaches, the machine is RAM- and CPU-constrained), or Lucene (slightly less headaches, but still). Before I proceed spending more time with a solution that might or might not work as advertised, I'd like to know: Did anyone ever get an actual, real-world search solution working in Django? I'm serious. I find it really frustrating reading about "large problems mostly solved", and then realizing that you will never get a working installation from the source-code because, actually, all bloggers dealing with those "mostly solved problems" never went past basic installation and copy-pasting the official tutorials. So here are the requirements: must be able to search for 10-100 terms in one query must handle + (term must be present) and - (term must not be present), AND/OR must handle arbitrary grouping (i.e. parentheses around AND/OR) must allow for Django-ORM filtering before or after fulltext-search (i.e. pre-/post-processing of results with the full set of filters that Django knows about) alternatively, there must be a facility to bulk-fetch the result set and transform it into a QuerySet should be light on the machine, so preferably no humongous JVM and Java-based app-server installation Is there anything out there that does this? I'm not interested in anecdotal evidence, or references to some blog posts that claim it should be working. I'd like to hear from someone who actually has a fully-functional setup working in the real world, under real conditions, with real queries. EDIT: Let me repeat again that I'm not so much interested in anecdotal evidence that someone, somewhere has a somewhat running installation working with unspecified properties. I already went there, I read all the blog posts, mailing lists, I contacted the authors, but when it came to actual implementation of real-world scenarios, nothing ever worked as advertised. Also, and a user below brought that point up as well, considering the TCO of any project, I'm definitely not interested in hearing that someone, somewhere was able to pull it off once a vendor parachuted in an unknown number of specialists to monkey-patch the whole installation with specific domain-knowledge that's documented nowhere. So, please, if you claim you have a working installation that actually satisfies minimum requirements for a full-fledged search (see requirements above), please provide the following so that we can all benefit from a search solution for Django that actually solves the problem: exact Linux distribution, release version, exact release version of Haystack (or equivalent) and release version of search backend, exact release version of the search engine publicly (!) available documentation how to set up all components exactly in the way that your installation was set up such that the minimal requirements above are met. Thank you.

  Read the article

• Is SQL Server DRI (ON DELETE CASCADE) slow?

  - by Aaronaught

  I've been analyzing a recurring "bug report" (perf issue) in one of our systems related to a particularly slow delete operation. Long story short: It seems that the CASCADE DELETE keys were largely responsible, and I'd like to know (a) if this makes sense, and (b) why it's the case. We have a schema of, let's say, widgets, those being at the root of a large graph of related tables and related-to-related tables and so on. To be perfectly clear, deleting from this table is actively discouraged; it is the "nuclear option" and users are under no illusions to the contrary. Nevertheless, it sometimes just has to be done. The schema looks something like this: Widgets | +--- Anvils (1:1) | | | +--- AnvilTestData (1:N) | +--- WidgetHistory (1:N) | +--- WidgetHistoryDetails (1:N) Nothing too scary, really. A Widget can be different types, an Anvil is a special type, so that relationship is 1:1 (or more accurately 1:0..1). Then there's a large amount of data - perhaps thousands of rows of AnvilTestData per Anvil collected over time, dealing with hardness, corrosion, exact weight, hammer compatibility, usability issues, and impact tests with cartoon heads. Then every Widget has a long, boring history of various types of transactions - production, inventory moves, sales, defect investigations, RMAs, repairs, customer complaints, etc. There might be 10-20k details for a single widget, or none at all, depending on its age. So, unsurprisingly, there's a CASCADE DELETE relationship at every level here. If a Widget needs to be deleted, it means something's gone terribly wrong and we need to erase any records of that widget ever existing, including its history, test data, etc. Again, nuclear option. Relations are all indexed, statistics are up to date. Normal queries are fast. The system tends to hum along pretty smoothly for everything except deletes. Getting to the point here, finally, for various reasons we only allow deleting one widget at a time, so a delete statement would look like this: DELETE FROM Widgets WHERE WidgetID = @WidgetID Pretty simple, innocuous looking delete... that takes over 2 minutes to run, for a widget with no data! After slogging through execution plans I was finally able to pick out the AnvilTestData and WidgetHistoryDetails deletes as the sub-operations with the highest cost. So I experimented with turning off the CASCADE (but keeping the actual FK, just setting it to NO ACTION) and rewriting the script as something very much like the following: DECLARE @AnvilID int SELECT @AnvilID = AnvilID FROM Anvils WHERE WidgetID = @WidgetID DELETE FROM AnvilTestData WHERE AnvilID = @AnvilID DELETE FROM WidgetHistory WHERE HistoryID IN ( SELECT HistoryID FROM WidgetHistory WHERE WidgetID = @WidgetID) DELETE FROM Widgets WHERE WidgetID = @WidgetID Both of these "optimizations" resulted in significant speedups, each one shaving nearly a full minute off the execution time, so that the original 2-minute deletion now takes about 5-10 seconds - at least for new widgets, without much history or test data. Just to be absolutely clear, there is still a CASCADE from WidgetHistory to WidgetHistoryDetails, where the fanout is highest, I only removed the one originating from Widgets. Further "flattening" of the cascade relationships resulted in progressively less dramatic but still noticeable speedups, to the point where deleting a new widget was almost instantaneous once all of the cascade deletes to larger tables were removed and replaced with explicit deletes. I'm using DBCC DROPCLEANBUFFERS and DBCC FREEPROCCACHE before each test. I've disabled all triggers that might be causing further slowdowns (although those would show up in the execution plan anyway). And I'm testing against older widgets, too, and noticing a significant speedup there as well; deletes that used to take 5 minutes now take 20-40 seconds. Now I'm an ardent supporter of the "SELECT ain't broken" philosophy, but there just doesn't seem to be any logical explanation for this behaviour other than crushing, mind-boggling inefficiency of the CASCADE DELETE relationships. So, my questions are: Is this a known issue with DRI in SQL Server? (I couldn't seem to find any references to this sort of thing on Google or here in SO; I suspect the answer is no.) If not, is there another explanation for the behaviour I'm seeing? If it is a known issue, why is it an issue, and are there better workarounds I could be using?

  Read the article

• Should we develop a custom membership provider in this case?

  - by Allen

  I'll be adding a bounty to this, probably 200, more if you guys think its appropriate. I wont accept an answer until I can add a bounty so feel free to go ahead and answer now Summary Long story short, we've been tasked with gutting the authentication and authorization parts of a fairly old and bloated asp.net application that previously had all of these components written from scratch. Since our application isn't a typical one, and none of us have experience in asp.net's built in membership provider stuff, we're not sure if we should roll our own authentication and authorization again or if we should try to work within the asp.net membership provider mindset and develop our own membership provider. Our Application We have a fairly old asp.net application that gets installed at customer locations to service clients on a LAN. Admins create users (users do not sign up) and depending on the install, we may have the software integrated with LDAP. Currently, the LDAP integration bulk-imports the users to our database and when they login, it authenticates against LDAP so we dont have to manage their passwords. Nothing amazing there. Admins can assign users to 1 group and they can change the authorization of that group to manage access to various parts of the software. Groups are maintained by Admins (web based UI) and as said earlier, granted / denied permissions to certain functionality within the application. All this was completely written from the ground up without using any of the built in .net authorization or authentication. We literally have IsLoggedIn() methods that check for login and redirect to our login page if they aren't. Our Rewrite We've been tasked to integrate more tightly with LDAP, they want us to tie groups in our application to groups (or whatever types of containers that LDAP uses) in LDAP so that when a customer opt's to use our LDAP integration, they dont have to manage their users in LDAP AND in our application. The new way, they will simply create users in LDAP, add them to Groups in LDAP and our application will see that they belong to the appropriate LDAP group and authenticate and authorize them. In addition, we've been granted the go ahead to completely rip out the User authentication and authorization code and completely re-do it. Our Problem The problem is that none of us have any experience with asp.net membership provider functionality. The little bit of exposure I have to it makes me worry that it was not intended to be used for an application such as ours. Though, developing our own ASP.NET Membership Provider and Role Manager sounds like it would be a great experience and most likely the appropriate thing to do. Basically, I'm looking for advice, should we be using the ASP.NET Membership provider & Role Management API or should we continue to roll our own? I know this decision will be influenced by our requirements so I'm going over them below Our Requirements Just a quick n dirty list Maintain the ability to have a db of users and authenticate them and give admins (only, not users) the ability to CRUD users Allow the site to integrate with LDAP, when this is chosen, they don't want any users stored in the DB, only the relationship between Groups as they exist in our app / db and the Groups/Containers as they exist in LDAP. .net 3.5 is being used (mix of asp.net webforms and asp.net mvc) Has to work in ASP.NET and ASP.NET MVC (shouldn't be a problem I'm guessing) This can't be user centric, administrators need to be the only ones that CRUD (or import via ldap) users and groups We have to be able to Auth via LDAP when its configured to do so I always try to monitor my questions closely so feel free to ask for more info. Also, as a general summary of what I'm looking for in an answer is just. "You should/shouldn't use xyz, here's why". Links regarding asp.net membership provider and role management stuff are very welcome, most of the stuff I'm finding is 5+ years old. Edit: Added some stuff to "Our Rewrite"

  Read the article

• In Ruby, how to I read memory values from an external process?

  - by grg-n-sox

  So all I simply want to do is make a Ruby program that reads some values from known memory address in another process's virtual memory. Through my research and basic knowledge of hex editing a running process's x86 assembly in memory, I have found the base address and offsets for the values in memory I want. I do not want to change them; I just want to read them. I asked a developer of a memory editor how to approach this abstract of language and assuming a Windows platform. He told me the Win32API calls for OpenProcess, CreateProcess, ReadProcessMemory, and WriteProcessMemory were the way to go using either C or C++. I think that the way to go would be just using the Win32API class and mapping two instances of it; One for either OpenProcess or CreateProcess, depending on if the user already has th process running or not, and another instance will be mapped to ReadProcessMemory. I probably still need to find the function for getting the list of running processes so I know which running process is the one I want if it is running already. This would take some work to put all together, but I am figuring it wouldn't be too bad to code up. It is just a new area of programming for me since I have never worked this low level from a high level language (well, higher level than C anyways). I am just wondering of the ways to approach this. I could just use a bunch or Win32API calls, but that means having to deal with a bunch of string and array pack and unpacking that is system dependant I want to eventually make this work cross-platform since the process I am reading from is produced from an executable that has multiple platform builds, (I know the memory address changes from system to system. The idea is to have a flat file that contains all memory mappings so the Ruby program can just match the current platform environment to the matching memory mapping.) but from the looks of things I'll just have to make a class that wraps whatever is the current platform's system shared library memory related function calls. For all I know, there could already exist a Ruby gem that takes care of all of this for me that I am just not finding. I could also possibly try editing the executables for each build to make it so whenever the memory values I want to read from are written to by the process, it also writes a copy of the new value to a space in shared memory that I somehow have Ruby make an instance of a class that is a pointer under the hood to that shared memory address and somehow signal to the Ruby program that the value was updated and should be reloaded. Basically a interrupt based system would be nice, but since the purpose of reading these values is just to send to a scoreboard broadcasted from a central server, I could just stick to a polling based system that sends updates at fixed time intervals. I also could just abandon Ruby altogether and go for C or C++ but I do not know those nearly as well. I actually know more x86 than C++ and I only know C as far as system independent ANSI C and have never dealt with shared system libraries before. So is there a gem or lesser known module available that has already done this? If not, then any additional information as to how to accomplish this would be nice. I guess, long story short, how do I do all this? Thanks in advance, Grg PS: Also a confirmation that those Win32API calls should be aimed at the kernel32.dll library would be nice.

  Read the article

• Variable mysteriously changing value

  - by Eitan

  I am making a simple tcp/ip chat program for practicing threads and tcp/ip. I was using asynchronous methods but had a problem with concurrency so I went to threads and blocking methods (not asynchronous). I have two private variables defined in the class, not static: string amessage = string.Empty; int MessageLength; and a Thread private Thread BeginRead; Ok so I call a function called Listen ONCE when the client starts: public virtual void Listen(int byteLength) { var state = new StateObject {Buffer = new byte[byteLength]}; BeginRead = new Thread(ReadThread); BeginRead.Start(state); } and finally the function to receive commands and process them, I'm going to shorten it because it is really long: private void ReadThread(object objectState) { var state = (StateObject)objectState; int byteLength = state.Buffer.Length; while (true) { var buffer = new byte[byteLength]; int len = MySocket.Receive(buffer); if (len <= 0) return; string content = Encoding.ASCII.GetString(buffer, 0, len); amessage += cleanMessage.Substring(0, MessageLength); if (OnRead != null) { var e = new CommandEventArgs(amessage); OnRead(this, e); } } } Now, as I understand it only one thread at a time will enter BeginRead, I call Receive, it blocks until I get data, and then I process it. The problem: the variable amessage will change it's value between statements that do not touch or alter the variable at all, for example at the bottom of the function at: if (OnRead != null) "amessage" will be equal to 'asdf' and at if (OnRead != null) "amessage" will be equal to qwert. As I understand it this is indicative of another thread changing the value/running asynchronously. I only spawn one thread to do the receiving and the Receive function is blocking, how could there be two threads in this function and if there is only one thread how does amessage's value change between statements that don't affect it's value. As a side note sorry for spamming the site with these questions but I'm just getting a hang of this threading story and it's making me want to sip cyanide. Thanks in advance. EDIT: Here is my code that calls the Listen Method in the client: public void ConnectClient(string ip,int port) { client.Connect(ip,port); client.Listen(5); } and in the server: private void Accept(IAsyncResult result) { var client = new AbstractClient(MySocket.EndAccept(result)); var e = new CommandEventArgs(client, null); Clients.Add(client); client.Listen(5); if (OnClientAdded != null) { var target = (Control) OnClientAdded.Target; if (target != null && target.InvokeRequired) target.Invoke(OnClientAdded, this, e); else OnClientAdded(this, e); } client.OnRead += OnRead; MySocket.BeginAccept(new AsyncCallback(Accept), null); } All this code is in a class called AbstractClient. The client inherits the Abstract client and when the server accepts a socket it create's it's own local AbstractClient, in this case both modules access the functions above however they are different instances and I couldn't imagine threads from different instances combining especially as no variable is static.

  Read the article

• Calculus? Need help solving for a time-dependent variable given some other variables.

  - by user451527

  Long story short, I'm making a platform game. I'm not old enough to have taken Calculus yet, so I know not of derivatives or integrals, but I know of them. The desired behavior is for my character to automagically jump when there is a block to either side of him that is above the one he's standing on; for instance, stairs. This way the player can just hold left / right to climb stairs, instead of having to spam the jump key too. The issue is with the way I've implemented jumping; I've decided to go mario-style, and allow the player to hold 'jump' longer to jump higher. To do so, I have a 'jump' variable which is added to the player's Y velocity. The jump variable increases to a set value when the 'jump' key is pressed, and decreases very quickly once the 'jump' key is released, but decreases less quickly so long as you hold the 'jump' key down, thus providing continuous acceleration up as long as you hold 'jump.' This also makes for a nice, flowing jump, rather than a visually jarring, abrupt acceleration. So, in order to account for variable stair height, I want to be able to calculate exactly what value the 'jump' variable should get in order to jump exactly to the height of the stair; preferably no more, no less, though slightly more is permissible. This way the character can jump up steep or shallow flights of stairs without it looking weird or being slow. There are essentially 5 variables in play: h -the height the character needs to jump to reach the stair top<br> j -the jump acceleration variable<br> v -the vertical velocity of the character<br> p -the vertical position of the character<br> d -initial vertical position of the player minus final position<br> Each timestep:<br> j -= 1.5; //the jump variable's deceleration<br> v -= j; //the jump value's influence on vertical speed<br> v *= 0.95; //friction on the vertical speed<br> v += 1; //gravity<br> p += v; //add the vertical speed to the vertical position<br> v-initial is known to be zero<br> v-final is known to be zero<br> p-initial is known<br> p-final is known<br> d is known to be p-initial minus p-final<br> j-final is known to be zero<br> j-initial is unknown<br> Given all of these facts, how can I make an equation that will solve for j? tl;dr How do I Calculus? Much thanks to anyone who's made it this far and decides to plow through this problem.

  Read the article

• After resolving and calling host via ipv6 with curl, next ipv4 request fails and vice versa

  - by Ranty

  I need to request the same host with different methods (using IPv4 and IPv6) from the same script. First request is always successful (no matter IPv4 or IPv6), but the second always fails with curl error 45 (Couldn't bind to IP). I'm using the following curl config: function v4_google() { $ch = curl_init(); curl_setopt($ch, CURLOPT_RETURNTRANSFER, 1); curl_setopt($ch, CURLOPT_FORBID_REUSE, 1); curl_setopt($ch, CURLOPT_FRESH_CONNECT, 1); curl_setopt($ch, CURLOPT_USERAGENT, 'Mozilla/5.0 (Windows NT 5.1; rv:15.0) Gecko/20100101 Firefox/15.0.1'); curl_setopt($ch, CURLOPT_URL, 'http://www.google.com/search?q=Moon'); curl_setopt($ch, CURLOPT_IPRESOLVE, CURL_IPRESOLVE_V4); curl_setopt($ch, CURLOPT_INTERFACE, 'My IPv4 address'); $c = curl_exec($ch); $result = !curl_errno($ch) ? 'Success' : '<b>' . curl_error($ch) . '; #' . curl_errno($ch) . '</b>'; echo '<p>v4_google:<br>Response length: ' . mb_strlen($c) . '<br>Result: ' . $result . '</p>'; curl_close($ch); } function v6_google() { $ch = curl_init(); curl_setopt($ch, CURLOPT_RETURNTRANSFER, 1); curl_setopt($ch, CURLOPT_FORBID_REUSE, 1); curl_setopt($ch, CURLOPT_FRESH_CONNECT, 1); curl_setopt($ch, CURLOPT_USERAGENT, 'Mozilla/5.0 (Windows NT 5.1; rv:15.0) Gecko/20100101 Firefox/15.0.1'); curl_setopt($ch, CURLOPT_URL, 'http://www.google.com/search?q=Moon'); curl_setopt($ch, CURLOPT_IPRESOLVE, CURL_IPRESOLVE_V6); curl_setopt($ch, CURLOPT_INTERFACE, 'My IPv6 address'); $c = curl_exec($ch); $result = !curl_errno($ch) ? 'Success' : '<b>' . curl_error($ch) . '; #' . curl_errno($ch) . '</b>'; echo '<p>v6_google:<br>Response length: ' . mb_strlen($c) . '<br>Result: ' . $result . '</p>'; curl_close($ch); } v6_google(); v4_google(); So long story short, if I query v6_google(); first, then all consecutive calls of v4_google(); are failing with the curl error 45 (Couldn't bind to IP). And vice versa. As you can see, I separated code into different functions and added CURLOPT_FORBID_REUSE and CURLOPT_FRESH_CONNECT plus curl_close($ch), but it didn't help at all. It looks like curl is caching the resolving method of every host you request, and even if you specify another resolving method the next time you call that host, the cached one is used instead. I would appreciate any help with this issue.

  Read the article

• Special characters from MySQL database (e.g. curly apostrophes) are mangling my XML

  - by Toph

  I have a MySQL database of newspaper articles. There's a volume table, an issue table, and an article table. I have a PHP file that generates a property list that is then pulled in and read by an iPhone app. The plist holds each article as a dictionary inside each issue, and each issue as a dictionary inside each volume. The plist doesn't actually hold the whole article -- just a title and URL. Some article titles contain special characters, like curly apostrophes. Looking at the generated XML plist, whenever it hits a special character, it unpredictably gobbles up a whole bunch of text, leaving the XML mangled and unreadable. (...in Chrome, anyway, and I'm guessing on the iPhone. Firefox actually handles it pretty well, showing a white ? in a black diamond in place of any special characters and not gobbling anything.) Example well-formed plist snippet: <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Rows</key> <array> <dict> <key>Title</key> <string>Vol. 133 (2003-2004)</string> <key>Children</key> <array> <dict> <key>Title</key> <string>No. 18 (Apr 2, 2004)</string> <key>Children</key> <array> <dict> <key>Title</key> <string>Basketball concludes historic season</string> <key>URL</key> <string>http://orient.bowdoin.edu/orient/article_iphone.php?date=2004-04-02&amp;section=1&amp;id=1</string> </dict> <!-- ... --> </array> </dict> </array> </dict> </array> </dict> </plist> Example of what happens when it hits a curly apostrophe: This is from Chrome. This time it ate 5,998 characters, by MS Word's count, skipping down to midway through the opening the title of a pizza story; if I reload it'll behave differently, eating some other amount. The proper title is: Singer-songwriter Farrell ’05 finds success beyond the bubble <dict> <key>Title</key> <string>Singer-songwriter Farrell ing>Students embrace free pizza, College objects to solicitation</string> <key>URL</key> <string>http://orient.bowdoin.edu/orient/article_iphone.php?date=2009-09-18&amp;section=1&amp;id=9</string> </dict> In MySQL that title is stored as (in binary): 53 69 6E 67 |65 72 2D 73 |6F 6E 67 77 |72 69 74 65 72 20 46 61 |72 72 65 6C |6C 20 C2 92 |30 35 20 66 69 6E 64 73 |20 73 75 63 |63 65 73 73 |20 62 65 79 6F 6E 64 20 |74 68 65 20 |62 75 62 62 |6C Any ideas how I can encode/decode things properly? If not, any idea how I can get around the problem some other way? I don't have a clue what I'm talking about, haha; let me know if there's any way I can help you help me. :) And many thanks!

  Read the article

• What can I do to improve a project if there is a no-listening situation. Developers vs Management

  - by NazGul

  Hi all, I hope that I'm not the only one and I can get a answer from someone with more experience than me, so I can think cleaner and I don't get depressed with this developer's life. I'm working as developer for a small company three years now. In that three years I'm working in the same project and sincerely, I think this project could be used as a CASE STUDY because it has all the situations that cannot happen in a project and that makes a project fails. To begin with, and I believe you've already noticed, the project has 3 years already (develoment only) and is still unfinished, because in every meeting there is a "new priority" ,or a "new problem" to be solve or a "new feature" to be add. So, first problem is no target set. How can you know when something is finished if you don't know what you want? I understand Management, because they see an oportunity and try to get that, but I don't understand how can they not see (or hear us) that they'll lose all they already have and what they'll eventually get. Second, there is no team group. My team consists of three people, a Senior Developer, a DBA and, finally, I for all the work (support, testing, new features, bug fixing, meeting, projet management of clients, etc) aka Junior Developer. The first (senior developer), does not perform any tests on his changes, so, most of the time, his changes give us problems (us = me, since I'm the one who will fix it). The second (DBA) is an uncompromising person and you can not talk to him, believe me, I tried! In his view, everything he does is fantastic... even if it is the most complicated to make it... And he does everything he wants, even if we need that only for 5 months later and would help some extra-hand to do the things we have to do for now. As you can see, there is very hard to work with no help... Third, there is no testings. Every... I repeat, Every release of the project, the customers wants to kill us, because there is a lot of bugs. Management? They say that they want tests before the release. Us? We say the same. Time? No time. Management? There is always some time to open the application and click in some buttons. Us? Try to explain that it is not so simple. Management doesn't care... end of story. Actually, must of the bugs could be avoid with a rigorous work... Some people just want to do the show to the Management. "Did you ask for this? Cool, it's done. Bugs? The Do-all-the-work guy will solve." Unfortunally for me, sometimes the Do-all-the-work also has to finish it. And to makes this all better, I'm the person who will listen the complaints from the customers. Cool, huh? I know, everyone makes mistakes. But there is mistakes and mistakes... To complete, in the Management view, "the problem is the lack of an individual project management", because we cannot do all the stuff they ask, even if there is no PM for the project itself. And ask us to work overtime without any reward... I do say all this stuff to the management and others members, but by telling this, the I'm the bad guy, the guy who is complain when everything is going well... but we need to work overtime... sigh What can I do to make it works? Anyone has a situation like this, what did you do? I hope you could understand my problem, my English is a little rusty. Thanks.

  Read the article

• Source code versioning with comments (organizational practice) - leave or remove?

  - by ADTC

  Before you start admonishing me with "DON'T DO IT," "BAD PRACTICE!" and "Learn to use proper source code control", please hear me out first. I am fully aware that the practice of commenting out old code and leaving it there forever is very bad and I hate such practice myself. But here's the situation I'm in. A few months ago I joined a company as software developer. I had worked in the company for few months as an intern, about a year before joining recently. Our company uses source code version control (CVS) but not properly. Here's what happened both in my internship and my current permanent position. Each time I was assigned to work on a project (legacy, about 8-10 years old). Instead of creating a CVS account and letting me check out code and check in changes, a senior colleague exported the code from CVS, zipped it up and passed it to me. While this colleague checks in all changes in bulk every few weeks, our usual practice is to do fine-grained versioning in the actual source code itself (each file increments in versions independent from the rest). Whenever a change is made to a file, old code is commented out, new code entered below it, and this whole section is marked with a version number. Finally a note about the changes is placed at the top of the file in a section called Modification History. Finally the changed files are placed in a shared folder, ready and waiting for the bulk check-in. /* * Copyright notice blah blah * Some details about file (project name, file name etc) * Modification History: * Date Version Modified By Description * 2012-10-15 1.0 Joey Initial creation * 2012-10-22 1.1 Chandler Replaced old code with new code */ code .... //v1.1 start //old code new code //v1.1 end code .... Now the problem is this. In the project I'm working on, I needed to copy some new source code files from another project (new in the sense that they didn't exist in destination project before). These files have a lot of historical commented out code and comment-based versioning including usually long or very long Modification History section. Since the files are new to this project I decided to clean them up and remove unnecessary code including historical code, and start fresh at version 1.0. (I still have to continue the practice of comment-based versioning despite hating it. And don't ask why not start at version 0.1...) I have done similar something during my internship and no one said anything. My supervisor has seen the work a few times and didn't say I shouldn't do such clean-up (if at all it was noticed). But a same-level colleague saw this and said it's not recommended as it may cause downtime in the future and increase maintenance costs. An example is when changes are made in another project on the original files and these changes need to be propagated to this project. With code files drastically different, it could cause confusion to an employee doing the propagation. It makes sense to me, and is a valid point. I couldn't find any reason to do my clean-up other than the inconvenience of a ridiculously messy code. So, long story short: Given the practice in our company, should I not do such clean-up when copying new files from project to project? Is it better to make changes on the (copy of) original code with full history in comments? Or what justification can I give for doing the clean-up? PS to mods: Hope you allow this question some time even if for any reason you determine it to be unfit in SO. I apologize in advance if anything is inappropriate including tags.

  Read the article

• Suggestions on how to map from Domain (ORM) objects to Data Transfer Objects (DTO)

  - by FryHard

  The current system that I am working on makes use of Castle Activerecord to provide ORM (Object Relational Mapping) between the Domain objects and the database. This is all well and good and at most times actually works well! The problem comes about with Castle Activerecords support for asynchronous execution, well, more specifically the SessionScope that manages the session that objects belong to. Long story short, bad stuff happens! We are therefore looking for a way to easily convert (think automagically) from the Domain objects (who know that a DB exists and care) to the DTO object (who know nothing about the DB and care not for sessions, mapping attributes or all thing ORM). Does anyone have suggestions on doing this. For the start I am looking for a basic One to One mapping of object. Domain object Person will be mapped to say PersonDTO. I do not want to do this manually since it is a waste. Obviously reflection comes to mind, but I am hoping with some of the better IT knowledge floating around this site that "cooler" will be suggested. Oh, I am working in C#, the ORM objects as said before a mapped with Castle ActiveRecord. Example code: By @ajmastrean's request I have linked to an example that I have (badly) mocked together. The example has a capture form, capture form controller, domain objects, activerecord repository and an async helper. It is slightly big (3MB) because I included the ActiveRecored dll's needed to get it running. You will need to create a database called ActiveRecordAsync on your local machine or just change the .config file. Basic details of example: The Capture Form The capture form has a reference to the contoller private CompanyCaptureController MyController { get; set; } On initialise of the form it calls MyController.Load() private void InitForm () { MyController = new CompanyCaptureController(this); MyController.Load(); } This will return back to a method called LoadComplete() public void LoadCompleted (Company loadCompany) { _context.Post(delegate { CurrentItem = loadCompany; bindingSource.DataSource = CurrentItem; bindingSource.ResetCurrentItem(); //TOTO: This line will thow the exception since the session scope used to fetch loadCompany is now gone. grdEmployees.DataSource = loadCompany.Employees; }, null); } } this is where the "bad stuff" occurs, since we are using the child list of Company that is set as Lazy load. The Controller The controller has a Load method that was called from the form, it then calls the Asyc helper to asynchronously call the LoadCompany method and then return to the Capture form's LoadComplete method. public void Load () { new AsyncListLoad<Company>().BeginLoad(LoadCompany, Form.LoadCompleted); } The LoadCompany() method simply makes use of the Repository to find a know company. public Company LoadCompany() { return ActiveRecordRepository<Company>.Find(Setup.company.Identifier); } The rest of the example is rather generic, it has two domain classes which inherit from a base class, a setup file to instert some data and the repository to provide the ActiveRecordMediator abilities.

  Read the article

• reloading page while an ajax request in progress gives empty response and status as zero

  - by Jayapal Chandran

  Hi, Browser is firefox 3.0.10 I am requesting a page using ajax. The response is in progress may be in readyState less than 4. In this mean time i am trying to reload the page. What happens is the request ends giving an empty response. I used alert to find what string has been given as response text. I assume that by this time the ready state 4 is reached. why it is empty string. when i alert the xmlhttpobject.status it displayed 0. when i alert the xmlhttpobject.statusText an exception occurs stating that NOT AVAILABLE. when i read in the document http://www.devx.com/webdev/Article/33024/0/page/2 it said for 3 and 4 status and statusText are available but when i tested only status is available but not satausText Here is a sample code. consider that i have requested a page and my callback function is as follows function cb(rt) { if(rt.readyState==4) { alert(rt.status); alert(rt.statusText); // which throws an exception } } and my server side script is as follows sleep(30); //flushing little drop down code besides these i noticed the following... assume again i am requesting the above script using ajax. now there will be an idle time till 30 seconds is over before that 30 seconds i press refresh. i got xmlhttpobject.status as 0 but still the browser did not reload the page untill that 30 seconds. WHY? so what is happening when i refresh a page before an ajax request is complete is the status value is set to zero and the ready state is set to 4 but the page still waits for the response from the server to end... what is happening... THE REASON FOR ME TO FACE SOME THING LIKE THIS IS AS FOLLOWS. when ever i do an ajax request ... if the process succeeded like inserting some thing or deleting something i popup a div stating that updated successfully and i will reload the page. but if there is any error then i do not reload the page instead i just alert that unable to process this request. what happens if the user reloads the page before any of this request is complete is i get an empty response which in my calculation is there is a server error. so i was debugging the ajax response to filter out that the connection has been interrupted because the user had pressed reload. so in this time i don't want to display unable to process this request when the user reloads the page before the request has been complete. oh... a long story. IT IS A LONG DESCRIPTION SO THAT I CAN MAKE EXPERTS UNDERSTAND MY DOUBT. so what i want form the above. any type of answer would clear my mind. or i would like to say all type of answers. EDIT: 19 dec. If i did not get any correct answer then i would delete this question and will rewrite with examples. else i will accept after experimenting.

  Read the article

• Submitting a URL into a Form without "http://", with "www.", or with neither

  - by John

  (EDITED) Hello, In the form below, the filed for <div class="urlfield"><input name="url" type="url" id="url" maxlength="500"></div> fine when a URL is submitted that has a "http://" at the beginning of it. However, it doesn't work if a URL is submitted with only a "www." in front of it, or with neither a "http://" nor a "www." How can I make it work in all if the submitted URL has any or none of the following at the beginning of it: http:// www. http://www. Thanks in advance, John Form: echo '<div class="submittitle">Submit an item.</div>'; echo '<form action="http://www...com/.../submit2.php" method="post"> <input type="hidden" value="'.$_SESSION['loginid'].'" name="uid"> <div class="submissiontitle"><label for="title">Story Title:</label></div> <div class="submissionfield"><input name="title" type="title" id="title" maxlength="1000"></div> <div class="urltitle"><label for="url">Link:</label></div> <div class="urlfield"><input name="url" type="url" id="url" maxlength="500"></div> <div class="submissionbutton"><input name="submit" type="submit" value="Submit"></div> </form> '; submit2.php: <?php if($_SERVER['REQUEST_METHOD'] == "POST"){header('Location: http://www...com/.../submit2.php');} require_once "header.php"; if (isLoggedIn() == true) { $remove_array = array('http://www.', 'http://', 'https://', 'https://www.', 'www.'); $cleanurl = str_replace($remove_array, "", $_POST['url']); $cleanurl = strtolower($cleanurl); $cleanurl = preg_replace('/\/$/','',$cleanurl); $cleanurl = stripslashes($cleanurl); $title = $_POST['title']; $uid = $_POST['uid']; $title = mysql_real_escape_string($title); $title = stripslashes($title); $cleanurl = mysql_real_escape_string($cleanurl); $site1 = 'http://' . $cleanurl; $displayurl = parse_url($site1, PHP_URL_HOST); function isURL($url1 = NULL) { if($url1==NULL) return false; $protocol = '(http://|https://)'; $allowed = '[-a-z0-9]{1,63}'; $regex = "^". $protocol . // must include the protocol '(' . $allowed . '\.)'. // 1 or several sub domains with a max of 63 chars '[a-z]' . '{2,6}'; // followed by a TLD if(eregi($regex, $url1)==true) return true; else return false; } if(isURL($site1)==true) mysql_query("INSERT INTO submission VALUES (NULL, '$uid', '$title', '$cleanurl', '$displayurl', NULL)"); else echo "<p class=\"topicu\">Not a valid URL.</p>\n"; } else { show_loginform(); } if (!isLoggedIn()) { if (isset($_POST['cmdlogin'])) { if (checkLogin($_POST['username'], $_POST['password'])) { show_userbox(); } else { echo "Incorrect Login information !"; show_loginform(); } } else { show_loginform(); } } else { show_userbox(); } require_once "footer.php"; ?>

  Read the article

• Form Not Submitting

  - by John

  Hello, When I try to click on the "submit" button for the form below, nothing happens. Any ideas why not? Thanks in advance, John submit.php: <?php require_once "header.php"; $u = $_SESSION['username']; if (!isLoggedIn()) { // user is not logged in. if (isset($_POST['cmdlogin'])) { // retrieve the username and password sent from login form & check the login. if (checkLogin($_POST['username'], $_POST['password'])) { show_userbox2(); } else { echo "Incorrect Login information !"; show_loginform(); } } else { show_loginform(); } } else { . show_userbox2(); } echo '<div class="submittitle">Submit an item.</div>'; echo '<form action="http://www...com/.../submit2.php" method="post"> <input type="hidden" value="'.$_SESSION['loginid'].'" name="uid"> <div class="submissiontitle"><label for="title">Story Title:</label></div> <div class="submissionfield"><input name="title" type="title" id="title" maxlength="1000"></div> <div class="urltitle"><label for="url">Link:</label></div> <div class="urlfield"><input name="url" type="url" id="url" maxlength="500"></div> <div class="submissionbutton"><input name="submit" type="submit" value="Submit"></div> </form> '; ?> submit2.php: <?php //if($_SERVER['REQUEST_METHOD'] == "POST"){header('Location: http://www...com/.../submit2.php');} require_once "header.php"; if (isLoggedIn() == true) { $remove_array = array('http://www.', 'http://', 'https://', 'https://www.', 'www.'); $cleanurl = str_replace($remove_array, "", $_POST['url']); $cleanurl = strtolower($cleanurl); $cleanurl = preg_replace('/\/$/','',$cleanurl); $title = $_POST['title']; //$url = $_POST['url']; $uid = $_POST['uid']; $title = mysql_real_escape_string($title); $cleanurl = mysql_real_escape_string($cleanurl); $site1 = 'http://' . $cleanurl; $displayurl = parse_url($site1, PHP_URL_HOST); function isURL($url1 = NULL) { if($url1==NULL) return false; $protocol = '(http://|https://)'; $allowed = '[-a-z0-9]{1,63}'; $regex = "^". $protocol . // must include the protocol '(' . $allowed . '\.)'. // 1 or several sub domains with a max of 63 chars '[a-z]' . '{2,6}'; // followed by a TLD if(eregi($regex, $url1)==true) return true; else return false; } if(isURL($site1)==true) mysql_query("INSERT INTO submission VALUES (NULL, '$uid', '$title', '$cleanurl', '$displayurl', NULL)"); else echo "<p class=\"topicu\">Not a valid URL.</p>\n"; } else { // user is not loggedin show_loginform(); } if (!isLoggedIn()) { // user is not logged in. if (isset($_POST['cmdlogin'])) { // retrieve the username and password sent from login form & check the login. if (checkLogin($_POST['username'], $_POST['password'])) { show_userbox(); } else { echo "Incorrect Login information !"; show_loginform(); } } else { // User is not logged in and has not pressed the login button // so we show him the loginform show_loginform(); } } else { // The user is already loggedin, so we show the userbox. show_userbox(); } require_once "footer.php"; ?>

  Read the article

• Styling an Input Field

  - by John

  Hello When I try to alter the CSS for the input field named "title" below, which is classed by "submissionfield", the position changes, but the height, length, and font of the field do not change. How could I make the height of the input field "title" 22 px, the length 550 px, and the font Times New Roman? The CSS below does not do it. Thanks in advance, John echo '<form action="http://www...com/.../submit2.php" method="post"> <input type="hidden" value="'.$_SESSION['loginid'].'" name="uid"> <div class="submissiontitle"><label for="title">Story Title:</label></div> <div class="submissionfield"><input name="title" type="title" id="title" maxlength="1000"></div> <div class="urltitle"><label for="url">Link:</label></div> <div class="urlfield"><input name="url" type="url" id="url" maxlength="500"></div> <div class="submissionbutton"><input name="submit" type="submit" value="Submit"></div> </form> '; The CSS: .submissiontitle { position:absolute; width:100px; left:30px; top:200px; text-align: left; margin-bottom:3px; padding:0px; font-family:Arial, Helvetica, sans-serif; font-size: 12px; color:#000000; } .submissionfield { position:absolute; width:550px; left:50px; top:230px; text-align: left; margin-bottom:3px; padding:0px; font-family: "Times New Roman", Times, serif; font-size: 22px; color:#000000; } .urltitle { position:absolute; width:250px; left:30px; top:300px; text-align: left; margin-bottom:3px; padding:0px; font-family:Arial, Helvetica, sans-serif; font-size: 12px; color:#000000; } .urlfield { position:absolute; width:550px; left:30px; top:330px; text-align: left; margin-bottom:3px; padding:0px; font-family:Arial, Helvetica, sans-serif; font-size: 11px; color:#000000; } .submissionbutton { position:absolute; width:250px; left:30px; top:380px; text-align: left; margin-bottom:3px; padding:0px; font-family:Arial, Helvetica, sans-serif; font-size: 11px; color:#000000; } .submittitle { position:absolute; width:250px; left:30px; top:150px; text-align: left; margin-bottom:3px; padding:0px; font-family:Arial, Helvetica, sans-serif; font-size: 12px; color:#000000; }

  Read the article

• What's a clean way to have the server return a JavaScript function which would then be invoked?

  - by Khnle

  My application is architected as a host of plug-ins that have not yet been written. There's a long reason for this, but with each new year, the business logic will be different and we don't know what it will be like (Think of TurboTax if that helps). The plug-ins consist of both server and client components. The server components deals with business logic and persisting the data into database tables which will be created at a later time as well. The JavaScript manipulates the DOM for the browsers to render afterward. Each plugin lives in a separate assembly, so that they won't disturb the main application, i.e., we don't want to recompile the main application. Long story short, I am looking for a way to return JavaScript functions to the client from an Ajax get request, and execute these JavaScript functions (which are just returned). Invoking a function in Javascript is easy. The hard part is how to organize or structure so that I won't have to deal with maintenance problem. So concat using StringBuilder to end up with JavaScript code as a result of calling toString() from the string builder object is out of the question. I want to have no difference between writing JavaScript codes normally and writing Javascript codes for this dynamic purpose. An alternative is to manipulate the DOM on the server side, but I doubt that it would be as elegantly as using jQuery on the client side. I am open for a C# library that supports chainable calls like jQuery that also manipulates the DOM too. Do you have any idea or is it too much to ask or are you too confused? Edit1: The point is to avoid recompiling, hence the plug-ins architecture. In some other parts of the program, I already use the concept of dynamically loading Javascript files. That works fine. What I am looking here is somewhere in the middle of the program when an Ajax request is sent to the server. Edit 2: To illustrate my question: Normally, you would see the following code. An Ajax request is sent to the server, a JSON result is returned to the client which then uses jQuery to manipulate the DOM (creating tag and adding to the container in this case). $.ajax({ type: 'get', url: someUrl, data: {'': ''}, success: function(data) { var ul = $('<ul>').appendTo(container); var decoded = $.parseJSON(data); $.each(decoded, function(i, e) { var li = $('<li>').text(e.FIELD1 + ',' + e.FIELD2 + ',' + e.FIELD3); ul.append(li); }); } }); The above is extremely simple. But next year, what the server returns is totally different and how the data to be rendered would also be different. In a way, this is what I want: var container = $('#some-existing-element-on-the-page'); $.ajax({ type: 'get', url: someUrl, data: {'': ''}, success: function(data) { var decoded = $.parseJSON(data); var fx = decoded.fx; var data = decode.data; //fx is the dynamic function that create the DOM from the data and append to the existing container fx(container, data); } }); I don't need to know, at this time what data would be like, but in the future I will, and I can then write fx accordingly.

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72  | Next Page >