Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 671/778 | < Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >

• How to wire 20 computers and 20 phones and 1 server into LAN?

  - by John Smith

  I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

  Read the article

• What is the correct iptables rule when NATing multiple private subnets?

  - by Jose Mendez

  I have a Centos minimal 6.5 acting as a router. eth0 is connected to a Cisco switch trunk port, allowing VLANs 200-213. I have several VLAN interfaces just as this link suggests: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s2-networkscripts-interfaces_802.1q-vlan-tagging.html And have IPv4 forwarding, so all my network devices from any of the networks 200-213 can communicate with each other using this linux box as their router. Problem is, I need them to access the Internet, so I added the following rule: iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to 1.1.1.56 1.1.1.56 is the "outside" address. This works fine, devices connected to the internal networks can ping Intertnet addresses BUT, they stop being able to talk to each other across subnets, so 192.168.211.55 can ping 8.8.8.8, but can't talk to 192.168.213.5. As soon as I do a service iptables restart to remove the rule, I can start talking across internal subnets again. What would be the correct way to set up NAT for multiple private subnets? Or maybe the correct way to set up forwarding?

  Read the article

• Windows 7 - system error 5 problem

  - by Ian

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• nameserver spoiling avahi multicast name resolution of .local domain

  - by Doug Coburn

  After trying to ping a machine on my local network, I noticed that I was trying hit address 66.152.109.24. This is an external public address. Resolution should have occurred via avahi mDNS. I ran dig to see how the name resolution worked and my quest/centurylink name server was retuning results for my .local domain queries! I tried a random name and got the same ip address result. $ dig jakdafj.local ; <<>> DiG 9.8.1-P1-RedHat-9.8.1-3.P1.fc15 <<>> jakdafj.local ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 58410 ;; flags: qr rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;jakdafj.local. IN A ;; ANSWER SECTION: jakdafj.local. 10 IN A 66.152.109.24 jakdafj.local. 10 IN A 204.232.231.46 ;; Query time: 104 msec ;; SERVER: 205.171.3.25#53(205.171.3.25) ;; WHEN: Sat Mar 24 20:40:17 2012 ;; MSG SIZE rcvd: 63 Am I missing something or is my DNS name server at 205.171.3.25 corrupted?

  Read the article

• snort analysis of wireshark capture

  - by Ben Voigt

  I'm trying to identify trouble users on our network. ntop identifies high traffic and high connection users, but malware doesn't always need high bandwidth to really mess things up. So I am trying to do offline analysis with snort (don't want to burden the router with inline analysis of 20 Mbps traffic). Apparently snort provides a -r option for this purpose, but I can't get the analysis to run. The analysis system is gentoo, amd64, in case that makes any difference. I've already used oinkmaster to download the latest IDS signatures. But when I try to run snort, I keep getting the following error: % snort -V ,,_ -*> Snort! <*- o" )~ Version 2.9.0.3 IPv6 GRE (Build 98) x86_64-linux '''' By Martin Roesch & The Snort Team: http://www.snort.org/snort/snort-team Copyright (C) 1998-2010 Sourcefire, Inc., et al. Using libpcap version 1.1.1 Using PCRE version: 8.11 2010-12-10 Using ZLIB version: 1.2.5 %> snort -v -r jan21-for-snort.cap -c /etc/snort/snort.conf -l ~/snortlog/ (snip) 273 out of 1024 flowbits in use. [ Port Based Pattern Matching Memory ] +- [ Aho-Corasick Summary ] ------------------------------------- | Storage Format : Full-Q | Finite Automaton : DFA | Alphabet Size : 256 Chars | Sizeof State : Variable (1,2,4 bytes) | Instances : 314 | 1 byte states : 304 | 2 byte states : 10 | 4 byte states : 0 | Characters : 69371 | States : 58631 | Transitions : 3471623 | State Density : 23.1% | Patterns : 3020 | Match States : 2934 | Memory (MB) : 29.66 | Patterns : 0.36 | Match Lists : 0.77 | DFA | 1 byte states : 1.37 | 2 byte states : 26.59 | 4 byte states : 0.00 +---------------------------------------------------------------- [ Number of patterns truncated to 20 bytes: 563 ] ERROR: Can't find pcap DAQ! Fatal Error, Quitting.. net-libs/daq is installed, but I don't even want to capture traffic, I just want to process the capture file. What configuration options should I be setting/unsetting in order to do offline analysis instead of real-time capture?

  Read the article

• Does water damage a fiber optic / cat5 cable

  - by chris

  One of the buildings I support recently had an adventure with a broken fire sprinkler. Lots of water everywhere. One of the "drains" the water used was the vertical risers between network closets. The cable plant in this building has bundles of cat5e as well as conduit with bundles of multimode fiber optic cables. The fiber is standard multi strand plenum rated stuff that terminates in boxes that have the patches to the switches. As far as I can tell, no water got near the ends of the cables (fiber or copper) but the conduit was saturated, and is likely still saturated because there isn't any air flow to dry the cables out. My gut reaction is that while it didn't do the cables any favors, it likely also isn't going to cause any problems. A little more reading / googling around leads me to believe that the water may cause problems down the road. Some pretty pictures so everyone knows what I'm talking about: Fiber conduit: Vertical riser, going down: Vertical riser, going up: Does anyone have any experience with this sort of damage and how to deal with it? Should we just ask the insurance adjuster to add "pull new structured cable" to the list of things to be replaced? And, if the opinion is "replace it because it'll start failing randomly over time" please include links that describe the specific failure modes, so I've got some ammo to use with the adjuster.

  Read the article

• Start daemon after specific samba share is mounted

  - by getack

  I axed this question on AskUbuntu, but it's not getting any traction from there... So I'll try here as well: I have a homebrew headless NAS running 12.04. In it I have a bunch of disks that are presented as a samba share thanks to Greyhole. If I want to do anything to the files within this share, I must do it through greyhole so that everything is updated properly. Thus, the share must be mounted locally and then accessed from there if I want to work on the files from the local machine. I do this mounting automatically thanks to these instructions. I also have Deluge installed that takes care of all my torrenting needs. Deluge's default download location is in this share, so that all the downloads are immediately available to the rest of the network. Obviously for everything to work, the share must be mounted, otherwise Deluge is going to have a problem downloading to it. The problem is, it seems like Deluge is starting before the shares are mounted when the system boots. So downloading/seeding does not continue automatically after boot. I have to log in and force a manual rescan and start on each torrent otherwise all the torrents just hangs on the error. Is there a way I can make deluge start after the shares got properly mounted? I looked into Upstart's emits functionality but I cannot seem to get it to work properly. Any advice?

  Read the article

• I keep losing wireless connection

  - by posfan12

  I have a WRT54GL v1.1 wireless router and a WUSB54G v4 wireless adapter, both made by Linksys. The router is in the living room by the TV and the my computer is in the bedroom. My ISP is Brighthouse. Operating System Microsoft Windows 7 Home Premium 64-bit SP1 CPU Intel Core 2 Duo E6600 @ 2.40GHz 36 °C Conroe 65nm Technology RAM 3.00GB Single-Channel DDR2 @ 333MHz (5-4-4-14) Motherboard eMachines EMCP73VT-PM (CPU 1) 26 °C Graphics ASUS VS247 (1920x1080@60Hz) 767MB GeForce GTX 460 (nVidia) 43 °C Hard Drives 466GB Seagate ST350041 8AS SCSI Disk Device (SATA) 35 °C Optical Drives HL-DT-ST DVDRAM GH41N SCSI CdRom Device Audio High Definition Audio Device The problem is that my Internet connection will work fine for 15 minutes or so. Then the data will just stop flowing. Windows says I am still connected, and the systray icon still shows five bars. But Comodo Firewall will stop showing up and down traffic, and another of my systray applications complains about a lack of connection. What I usually do is either disconnect from the network manually, or unplug and re-plug the USB adapter. At which point the connection will work properly for another 15 minutes. I've tried unplugging my router for 30 seconds and letting it reboot. I've also tried looking for a newer driver for my adapter but I seem to have the latest version 3.1.3.0. This is a recent problem starting about a week ago. For the previous several months things were working just fine. I haven't made any changes to my system that I am aware of. The only thing I did was open my case to blow the dust out of it, then put everything back together. How do I fix this issue?

  Read the article

• Intermittent unavailability of an instance in a failover cluster while a standby node is offline in

  - by Emil Fridriksson

  Hi everyone. I've got a small failover cluster that I run for the websites my company has. During a RAM upgrade of the standby server, our websites started to show errors about not being able to access the database server. I verified that the instance was indeed up and the server accessable via remote desktop. I also tried a SQL connection to it and it worked, but that might have been after it became available again. This happened on and off until we were able to roll back the hardware changes that were in progress on the standby server and we were able to bring it back up. There was nothing of interest in the SQL Server log, but there is a continous log for the whole duration of the problem, so there was no restart of the SQL Server service. The event viewer is of more interest, since it shows events relating to the heartbeat network card, but I don't know how that would affect the availability of the server, since the standby node is offline. I'd appreciate any help you can provide, it's not very redundant if the setup depends on the standby server being up. :) Here are the event logs from the time of the problem, I include all of them since I can't seem to see what could possibly be the cause of the problem. Event log: http://hlekkir.com:800/htmltable.htm

  Read the article

• connect server to server on secondary NIC

  - by microchasm

  Hi, I have a CentOS box with multiple NIC's running Apache. I also have another box running RHEL that will be the MySQL server. I'm trying to use the secondary NIC on the Apache box to connect directly to the MySQL server, but so far no luck. I want to isolate the MySQL box as much as possible which is why I'm going for a direct connection as opposed to running through a switch. I have a crossover cable running between them. IP configs: Apache box eth0 [to lan] ip addr: 192.168.200.100 netmask: 255.255.0.0 gateway: 192.168.111.1 eth1 [to mysql] ip addr: 192.168.200.101 netmask: 255.255.0.0 gateway: [blank] MySQL box eth0 [to apache] ip addr: 192.168.200.203 netmask: 255.255.0.0 gateway: 192.168.200.201 The rest of our network is on 192.168.111.0/24 subnet. Ping only returns Destination Host Unreachable. I've tried various variations of this setup (including straight through cable), and I can't seem to get them to talk to each other. Any help appreciated.

  Read the article

• Vagrant up doesn't load chef configs and doesn't keep an error log

  - by la_f0ka

  I'm trying to set up a vagrant box and I'm running with all sort of troubles. Right now I'm getting a strange error message where it states there's a stack trace file with more info, but that file is no where to be found. This is the error: stdin: is not a tty [Sun, 16 Sep 2012 18:31:47 +0000] INFO: *** Chef 0.10.0 *** [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Setting the run_list to ["recipe[apt]", "recipe[openssl]", "recipe[apache2]", "recipe[mysql]", "recipe[mysql::server]", "recipe[php]", "recipe[php::module_apc]", "recipe[php::module_curl]", "recipe[php::module_mysql]", "recipe[apache2::mod_php5]", "recipe[apache2::mod_rewrite]"] from JSON [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Run List is [recipe[apt], recipe[openssl], recipe[apache2], recipe[mysql], recipe[mysql::server], recipe[php], recipe[php::module_apc], recipe[php::module_curl], recipe[php::module_mysql], recipe[apache2::mod_php5], recipe[apache2::mod_rewrite]] [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Run List expands to [apt, openssl, apache2, mysql, mysql::server, php, php::module_apc, php::module_curl, php::module_mysql, apache2::mod_php5, apache2::mod_rewrite] [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Starting Chef Run for natty.talifun.com [Sun, 16 Sep 2012 18:31:48 +0000] ERROR: Running exception handlers [Sun, 16 Sep 2012 18:31:48 +0000] ERROR: Exception handlers complete [Sun, 16 Sep 2012 18:31:48 +0000] FATAL: Stacktrace dumped to /tmp/vagrant-chef-1/chef-stacktrace.out [Sun, 16 Sep 2012 18:31:48 +0000] FATAL: NameError: wrong constant name Chef-symfony2Console Chef never successfully completed! Any errors should be visible in the output above. Please fix your recipes so that they properly complete. And this is what my vagrantfile looks like: Vagrant::Config.run do |config| config.vm.box = "ubuntu-1104-server-i386" config.vm.network :hostonly, "33.33.33.33" config.vm.forward_port 80, 8000 config.vm.share_folder "symfony.tests", "/var/www/symfony.tests", "data", :nfs => true config.vm.provision :chef_solo do |chef| chef.cookbooks_path = ["../my-recipes/cookbooks", "site-cookbooks"] chef.add_recipe "apt" chef.add_recipe "openssl" chef.add_recipe "apache2" chef.add_recipe "mysql" chef.add_recipe "mysql::server" chef.add_recipe "php" chef.add_recipe "php::module_apc" chef.add_recipe "php::module_curl" chef.add_recipe "php::module_mysql" chef.add_recipe "apache2::mod_php5" chef.add_recipe "apache2::mod_rewrite" chef.add_recipe "Symfony" chef.json = { :mysql => { :server_root_password => 'root', :bind_address => '127.0.0.1' } } end end

  Read the article

• How do I get a Mac to request a new IP address from another DHCP server running in parallel while Ne

  - by huyqt

  Hello, I have an interesting situation. I'm trying to us a Linux based machine to allow Mac's to Netboot (similiar to PXE boot) by running a DHCP service in parallel with the "global" DHCP server. The local DHCP server hands out IPs in a private subnet, e.g., 10.168.0.10-10.168.254-254, while the "global" DHCP server hands out IPs from the IP range 10.0.0.1 - 10.0.1.254. The local DHCP range is only supposed to be used in Preboot Execution Environment and Netboot. The local DHCP server is something I have control over, but I do not have access to the global DHCP server. I have a filter to only allow members with the vendor strings "AAPLBSDPC/i386" and "PXEClient". PXE works fine, but Netboot has a quirk. The Apple systems that haven't been connected to the network yet can Netboot fine. But once it grabs a "real" IP address from the global DHCP server, it will "save" it and request it the next time we want it to netboot (which the local dhcp server won't give it). This is what I want: Mar 30 10:52:28 dev01 dhcpd: DHCPDISCOVER from 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:29 dev01 dhcpd: DHCPOFFER on 10.168.222.46 to 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:31 dev01 dhcpd: DHCPREQUEST for 10.168.222.46 (10.168.0.1) from 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:31 dev01 dhcpd: DHCPACK on 10.168.222.46 to 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:32 dev01 in.tftpd[5890]: tftp: client does not accept options Mar 30 10:52:53 dev01 in.tftpd[5891]: tftp: client does not accept options Mar 30 10:52:53 dev01 in.tftpd[5893]: tftp: client does not accept options Mar 30 10:52:54 dev01 in.tftpd[5895]: tftp: client does not accept options This is what I get when it already has a "stored" IP: Mar 30 10:51:29 dev01 dhcpd: DHCPDISCOVER from 00:25:xx:xx:xx:xx via eth1 Mar 30 10:51:30 dev01 dhcpd: DHCPOFFER on 10.168.222.45 to 00:25:xx:xx:xx:xx via eth1 Mar 30 10:51:31 dev01 dhcpd: DHCPREQUEST for 10.0.0.61 (10.0.0.1) from 00:25:xx:xx:xx:xx via eth1: ignored (not authoritative). Do you have any suggestions? It would be much appreciated.

  Read the article

• How to direct reverse proxy requests using wildcard vhosts

  - by HonoredMule

  I'm interested in running a reverse proxy with 2-3 virtual machines behind it. Each internal server will run multiple virtual hosts, and rather than manually configuring each individual vhost on the proxy (a variety of vhosts come and go too often for this to be practical), I would like to use something which can employ pattern matching in a sequential order to find the appropriate back-end server. For example: Server 1: *.dev.mysite.com Server 2: *.stage.mysite.com Server 3: *.mysite.com, dev.mysite.com, stage.mysite.com, mysite.com Server 4: * In the above configuration, task.dev.mysite.com would go to Server 1, dev.mysite.com would go to Server 3, yoursite.stage.mysite.com to Server 2, www.mysite.com to Server 3, and yoursite.com to Server 4. I've looked into using Squid, Varnish, and nginx so far. I have my opinions regarding their respective desirability and general suitability, but it's not readily apparent if any of them can handle dynamic server selection in this manner and not require per-vhost configuration. Apache on the other hand can do this handily and simply, but otherwise (aside from being well-known and familiar) seems very poorly suited to the partly-performance-serving task. Performance isn't actually a major concern yet, but it seems foolish to use Apache if another system will perform far better and can also handle the desired 'hands-free' configuration. But so is frequently having to adjust the gateway for all production services and risk network-wide outage...and so also is setting oneself up for longer downtime later if Apache becomes a too-small bottleneck. Which of these (or other) reverse proxies can do it/would do it best? And maybe I should post this as a separate question, but if Apache is the only practical option, how safe/reliable/predictable is apache-mpm-event in apache2.2 (Ubuntu 12.04.1) particularly for a dedicated reverse proxy? As I understand it the Event MPM was declared "safe" as of 2.4 but it's unclear whether reaching stability in 2.4 has any implications for the older (2.2) versions available in official/stable package channels of various distros.

  Read the article

• Windows 7 Media Center PC not displaying MKV files properly

  - by David

  Does anyone know why Windows Media Center wouldn't correctly display a 16x9 video? I just upgraded my home-built HTPC from Vista Ultimate (hey, it was a giveaway) to Windows 7 Ultimate - clean install. After that, I installed the Divx7 beta (to get .MKV support) and AC3filter (so I could HEAR the MKV files). Previously, under Vista Ultimate (32 bit), I had Arcsoft's Total Theater Pro for playing Blu-Rays and MKV decoding under Media Center. Now when I play a 720p 16x9 MKV file, I get some 'letterboxing' - like it's halfway between 4x3 and 16x9 - with the aspect ration looking alightly squished as a result. Here's the wierd part. If I use the Media Center connection software in my XBox 360 - it plays perfectly, filling the 16x9 screen edge-to-edge, just like Vista's WMC software USED to. Of course, beats the network up because the XBox goes to the HTPC, the HTPC goes to my WHS machine to fetch the data, it comes back to the HTPC, gets transcoded and streamed back to the Xbox. I'm running the latest drivers for an NVidia card (as fetched by Windows 7). I have no idea WHY this is because if I play "ordinary" (i.s. SD) Divx files that are 16x9, they play just fine, scaled right up to my screen's edges. It puzzles me as to why the same machine that properly converts the bits for the Xbox can't display/scale them properly for the attached display. Mind you, Windows Media Player exhibits the same symptoms. Ideas?

  Read the article

• Moving automatically spam messages to a folder in Postfix

  - by cad

  Hi My problem is that I want to automatically to move spam messages to a folder and not sure how. I have a linux box giving email access. MTA is Postfix, IMAP is Courier. As webmail client I use Squirrelmail. To filter SPAM I use Spamassassin and is working ok. Spamassasin is overwriting subjects with [--- SPAM 14.3 ---] Viagra... Also is adding headers: X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on xxxx X-Spam-Level: ************** X-Spam-Status: Yes, score=14.3 required=2.0 tests=BAYES_99, DATE_IN_FUTURE_24_48,HTML_MESSAGE,MIME_HTML_ONLY,RCVD_IN_PBL, RCVD_IN_SORBS_WEB,RCVD_IN_XBL,RDNS_NONE,URIBL_RED,URIBL_SBL autolearn=no version=3.2.5 X-Spam-Report: * 0.0 URIBL_RED Contains an URL listed in the URIBL redlist * [URIs: myimg.de] * 3.5 BAYES_99 BODY: Bayesian spam probability is 99 to 100% * [score: 1.0000] * 0.9 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL * [113.170.131.234 listed in zen.spamhaus.org] * 3.0 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL * 0.6 RCVD_IN_SORBS_WEB RBL: SORBS: sender is a abuseable web server * [113.170.131.234 listed in dnsbl.sorbs.net] * 3.2 DATE_IN_FUTURE_24_48 Date: is 24 to 48 hours after Received: date * 0.0 HTML_MESSAGE BODY: HTML included in message * 1.5 MIME_HTML_ONLY BODY: Message only has text/html MIME parts * 1.5 URIBL_SBL Contains an URL listed in the SBL blocklist * [URIs: myimg.de] * 0.1 RDNS_NONE Delivered to trusted network by a host with no rDNS I want to automatically to move spam messages to a folder. Ideally (not sure if possible) only to move messages with puntuation 5.0 or more to folder.. spam between 2.0 and 5.0 I want to be stored in Inbox. (I plan later to switch autolearn on) After reading a lot in procmail, postfix and spamassasin sites and googling a lot (lot of outdated howtos) I found two solutions but not sure which is the best or if there is another one: Put a rule in squirrelmail (dirty solution?) Use Procmail Which is the best option? Do you have any updated howto about it? Thanks

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• suggestions for firewall/router project using *BSD or Linux

  - by Adeodatus

  Hi All, I have a project in mind and I'd love to hear some ideas on some open source solutions with COTS hardware. I have a few 24 and/or 48 port managed layer2 switches with customers potentially on each port (though its usually about 20-30). Right now the switch has a bridged network and backhaul the traffic to our core to a centralized DHCP server. I need to move them to a NAT solution and, while doing this, I'd like to protect the customers on each port from the customer traffic on the other ports. I also need to be able to port forward from the public side of the firewall/nat box to specific hardware on the inside of the nat machine (easy enough, I know). My first thoughts are to build an appliance-like box (the fewer moving parts the better) that can do filtering and NAT with rfc1918 an address range being handed out via a DHCP server on the appliance. A caching DNS server on the appliance would be a plus since we backhaul everything to the core. I'd like to run FreeBSD but I'm open. Now, to try to limit the broadcast traffic thats visible I was thinking of doing each port on the switch as a different vlan and have the switch do trunking to the private NIC on the FreeBSD/appliance. I'd probably need to do some magic on the freebsd NIC to get this working but it should. We have the parts to build these systems. So, does this make sense? Are there any other solutions out there that we don't have to spend money on but can use our parts to create something? Are there any good distros that could do this already (monowall)?? I may or may not admin this solution so a secure web configuration and management tool would be a plus in the other admins' minds. Thoughts?

  Read the article

• Remote server security: handling compiler tools

  - by Gonzolas

  Hello! I was wondering wether to remove compiler tools (gcc, make, ...) from a remote production server, mainly for security purposes. Background: The server runs a web application on Linux. Consider Apache jailed. Otherwise, only OpenSSHd faces the public network. Of course there is no compiler stuff within the jail, so this is about the actual OS outside of any jails. Here's my personal PRO/CON list (regarding removal) so far: PRO: I had been reading some suggestions to remove compiler tools in order inhibit custom building of trojans etc. from within the host if an attacker attains unpriviliged user permissions. CON: I can't live without Perl/Python and a trojan/whatever could be written in a scripting language like that, anyway, so why bother about removing gcc et al. at all. There is a need to build new Linux kernels as well as some security tools from source directly on the server, because the server runs in 64-bits mode and (to my understanding) I can't (cross-)compile locally/elsewhere due to lack of another 64-bits hardware system. OK, so here are my questions for you: (a) Is my PRO/CON assessment correct? (b) Do you know of other PROs / CONs to removing all compiler tools? Do they weigh in more? (c) Which binaries should I consider dangerous if the given PRO statement holds? Only gcc, or also make, or what else? Should I remove the enitre software packages them come with? (d) Is it OK to just move those binaries to a root-only accessible directory when they are not needed? Or is there a gain in security if I "scp them in" every time? Thank you!

  Read the article

• Configure Domino to use SMTP routing and hMailServer

  - by Sébastien Lachance

  I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

  Read the article

• Permissions won't cascade more than 1 level

  - by Jovin_

  Running Windows Small Business Server 2011 I have a file structure with a lot of sub folders (sometimes 5-6 levels deep). I have created access groups to grant access to my users, and also deny groups to deny access to others. X Access & X Deny. These allow or deny access to a mapped network drive X: On the server I put in the groups with Full Control Allow for X Access and Full Control Deny for X Deny, I also tick the box "Apple these permissions to objects and/or containers within this container only" and have ensured that "Apply to:" is "This folder, subfolders and files". But for some reason the permissions will only apply to the next level of folders & files. ex. structure: X: Folder 1 Folder 1a Folder 2 Folder 2a If I apply the permissions to X: it'll only go to Folder 1 & 2, not 1a and 2a, I then need to manually apply the permissions to these too. Is this working as intended or am I doing something wrong?

  Read the article

• Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

  - by dgwilson

  We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

  Read the article

• Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

  - by dgwilson

  We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

  Read the article

• apache2: ssl_error_rx_record_too_long when visiting port 80? help!

  - by John

  Hi, I have an Ubuntu 10 x64 server edition machine. I got a second IP and configured /etc/network/interfaces like so (actual IPs and gateways removed): [code] auto lo iface lo inet loopback iface eth0 inet dhcp auto eth0 auto eth0:0 iface eth0 inet static address [ my first IP ] netmask 255.255.255.0 gateway [ my first gateway ] iface eth0:0 inet static address [ my second IP ] netmask 255.255.255.0 gateway [ my second gateway ] [/code] /etc/apache2/ports.conf: [code] Listen 80 NameVirtualHost [ my first IP ]:80 NameVirtualHost [ my second IP ]:80 # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 NameVirtualHost [ my first IP - some site is running SSL successfully using it ]:443 Listen 443 [/code] /etc/apache2/sites-enabled/mysite.conf: [code] ServerName mysite.com Include /var/www/mysite.com/djangoproject/apache/django.conf [/conf] [/code] Then when visiting http[mysite].com:80 or http[mysite].com (:// removed because serverfault doesn't allow me to post hyperlinks), I get: [code] An error occurred during a connection to [mysite].com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) [/code] My guess is that the configuration file is not being picked up, and apache is therefore looking for the default-ssl file, which is not in conf-enabled. If I were to configure that file properly, it seems I would successfully connect to whatever default directory is specified in the default-ssl file. But I want to connect to my website. Any ideas? Thanks in advance!

  Read the article

• Long Gigabit Ethernet Run

  - by Timothy R. Butler

  I am trying to get an Gig-E network between two buildings that are approximately 260 ft. away. While some TRENDnet switches failed to be able to connect to each other over Cat 6 at that distance, two Netgear 5-port Gig-E switches do so just fine. However, it still fails after I put in place APC PNET1GB ethernet surge protectors at each end before the line connects to the respective switches. So I find myself wondering if I simply need to find a better surge protector that doesn't degrade the signal as much (if so, what kind would you recommend?) or if I should give up on copper and use fiber between the buildings. If I opt to go the latter route, I could really use some pointers. It looks like LC connectors are the most common, but I keep running into some others as well. A media converter on each end seems like the simplest solution, but perhaps a Gig-E switch with an SFP port would make more sense? Given a very limited budget, sticking with my existing copper seems best, but if it is bound to be a headache, a 100 meter fiber cable is something I think I can swing cost wise.

  Read the article

• File sharing for small, distributed, non-technical, non-profit organization?

  - by mnmldave

  Problem: I've started volunteering for a small non-profit with fewer than five non-technical Windows users who need to share 20-30GB of files (Office documents, images, PDFs, etc.) amongst themselves online. Background: The users are accustomed to a Windows network share on a machine that backed up their data locally. An on-site "disaster" has forced them to work from their homes for awhile and to re-evaluate their file sharing needs (office was located in an old building with obvious electrical issues, etc.). Access to time from volunteers with IT experience seems to be difficult. Demonstrably minimizing energy consumption is a nice-to-have. I'm currently considering Jungle Disk (a Desktop account shared amongst the handful of employees since their TOS and my inquiries to their helpdesk seem to indicate this is permissible). It appears easy-to-use, inexpensive, secure, has backup functionality, and can scale to accomodate more data when needed. I've not used it myself though (have only used Dropbox for personal use) and systems isn't my area of expertise, so am worried I might be jumping on a bandwagon. That said, any suggestions, thoughts or similar experiences would be really appreciated.

  Read the article

< Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >