Search Results

Search found 20475 results on 819 pages for 'voice control'.

Page 671/819 | < Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >

  • Looking for suitable backup solution Mac OS X to offsite Centos 6 server 1TB of working data

    - by Brady
    I'll start by saying what we have in place currently: On site file server (Mac OS X Server) that is used by GFX designers and they have a working 1TB of data. Offsite server with 2TB available storage (Centos 6) Mac OS X server rsync data to offsite server every 6 hours (rsync -avz --delete --progress -e ssh ...) Mac OS X server does full data backup to LTO 4 tape on a 10 day recycle (Mon-Fri for 2 weeks) rsync pushes about 60GB of file changes a day. The problem: The onsite tape backup is failing as 1TB of graphics files don't compress well to fit onto a 800GB LTO4 tape. Backup is incredibly slow doing a full backup. Pain in the backside getting people to remember to change the tape. Often gets forgotten etc The quick solution: Buy LTO5 Drive and tapes. However this has been turned down because of the cost... What I would like: Something that works in the same way rysnc works. Only changed data is sent over the wire and can be scheduled to run multiple times during the day. Data that is sent is compressed and sent over SSH. Something that keeps a 14day retention but doesn't keep duplicate data So as an example if I have 1TB of working data and 60GB of changes are made each day then I expect around 1.84TB of data to be stored on the offsite server. To work with the Mac OS X server and Centos 6 server. Not cost an arm and a leg. Must be a cheaper solution than buying an LTO5 drive with tapes (around £1500). Be able to be setup to run autonomously. Have some sort of control panel that will allow an admin to easily restore a file/folder. Any recommendations?

    Read the article

  • Eee PC Seashell series netbook screen is cut off at bottom no matter the resolution

    - by Yzmir Ramirez
    I have an Eee PC 1015PE Seashell netbook running Windows 7 Home Premium with an Intel Graphics Media Accelerator 3150 (8.14.10.2230) with a "Generic Non-PnP Monitor" detected. I tried: Changing the resolution (Control Panel = Appearance and Personalization = Display = Screen Resolution) to 1024x768 Updating the video driver (to 8.14.10.2230) Uninstalling the driver and rebooting Pressing the Windows Key + "-" (magnifier) Pressing Ctrl + Mouse Scroll only resizes the desktop items Pressing Fn + F4 shows 1024x600 (which I think is what I should be using, but nothing happens) EDIT: Changed from Landscape to Portrait and it works Attached an External Monitor and when I extend or set as desktop it works only on the External Monitor (shows up as "Generic PnP Monitor in Device Manager) Basically the bottom inch of my desktop is off-screen hiding my start bar, but my wigets are in their proper position (the start bar is not hidden). Pressing Ctrl + Esc shows the start menu but its cut-off. I'm pretty sure I should be using 1024x600 resolution, any advice? What's odd is that this only started happening recently. EDIT2: Here are some screenshots showing the problem: Resized Window to fit: Opened Start Menu - notice it cut off: Maximized window and then scrolled down - notice no Start Menu: I downgraded my graphic driver I downloaded from the Intel Download Center for the Graphic Media Accelerator 3150 (now: 8.14.10.1972) and now my "Generic non-PnP Montior" detects as "Digital Flat Panel (1024x768 60Hz)".

    Read the article

  • File permissions question

    - by Matthew Robert Keable
    I just switched my site's server from Windows to Linux, and am finally able to control file permissions from my ftp. So, seeing that all permissions were 705 by default (and not wanting just anyone to have permission to execute), I went and changed everything to 744. Now, gif and jpg links don't work, pdf download links don't work, php links don't load, and mov files don't play. Conversely, all html files work perfectly. Setting things back doesn't seem to help. Even setting to 777 gets me nowhere. Any ideas on what might be going wrong? I've been googling file permissions all day (solved that problem with the Windows-Linux switch, which has bred a new problem), and I don't think anything I can find has escaped my attention. The site: absis-minas.com Go easy on a n00b. I took up learning php out of interest, and wound up delving into server management issues due to a very simple line of code not working the way it was supposed to. Thanks!

    Read the article

  • Allow opening a new tab with Ctrl+T on all websites in Firefox

    - by Martin J.H.
    In Firefox, certain websites and plugins (Adobe PDF Plugin) appear to "capture" the Control key, so that when I try to open a new tab using "Ctrl+t", nothing happens - or worse, something unexpected happens. Examples: On the Codecademy site, while editing code, Ctrl+T either does nothing, or (when Flash is disabled) switches the position of the two characters next to the cursor. When viewing PDF's with the Adobe PDF Plugin, Ctrl+T does nothing. Is there a way to disable this "feature"? I would like "Ctrl+t" to always "talk" to Firefox! Edit: After searching superuser deeper, this question is very similar to the questions: "How to prevent keystroke grabbing/hijacking by websites in Firefox?" "How do I prevent pages I visit from overriding selected Firefox shortcut keys?". The answers to these questions are interesting and relevant, but do not give a method on how to disable combinatinos such as "Ctrl+t". Maybe a modified Greasemonkey script is the easiest solultion. Edit 2 - Attempt at a solution The following UserScript (Use GreaseMonkey to install it) successfully captures Ctrl+t on some sites (Google Search site, for instance - PopUp "Gotcha" appears), but not on the Codecademy site. I found another question pertaining to this subject here: "How to forbid keyboard shortcut stealing by websites in Firefox". It was raised in 2010, and the consensus was: It can't be done. // ==UserScript== // @name Disable Ctrl T interceptions // @description Stop websites from highjacking keyboard shortcuts // // @run-at document-start // @include * // @grant none // ==/UserScript== // Keycode for 't'. Add more to disable other ctrl+X interceptions keycodes = [84]; var lastPressedButton = [0]; document.addEventListener('keydown', function(e) { //uncomment to find out the keycode for any given key // alert(e.keyCode ); if (keycodes.indexOf(e.keyCode) != -1 && e.ctrlKey) { e.cancelBubble = true; e.stopImmediatePropagation(); alert("Gotcha!"); } return false; });

    Read the article

  • How to fix Quicktime video color problems on nVidia chipset and Windows XP?

    - by Matthew Glidden
    My laptop frequently plays video as if in very low-color mode. Though the sound remains clear, it looks terrible, showing only a few shades of red, blue, or yellow. (It's even worse than 8-bit color.) The problem doesn't happen consistently, so I'm looking for troubleshooting advice or known solutions. I use a Dell Latitude D620 laptop with Windows XP, on-board nVidia video chipset, Quicktime, and multiple monitors (laptop screen + VGA-connected LCD). Color problems happen in each application I tried, iTunes, a browser, and the Quicktime standalone player. It doesn't happen right after reboot, so could be from a sleep-wake cycle, or at least being on for an extended period. Google results suggest reinstalling nVidia drivers, which I've done several times with no change. I have found 2 workarounds. Reboot, sacrificing significant time and disrupting work In nVidia control panel, change color to 16-bit, and then back to 32-bit This happens with all video playback, so it's definitely not one corrupt file. I use workaround #2 consistently, but would love a longer-term solution.

    Read the article

  • Wget save cookies not working

    - by TrymBeast
    I've been trying to login in the pyload through the web api, but wget is not saving the cookies and I don't understand why. I'm using the following command: wget --delete-after --keep-session-cookies --save-cookies=my_cookies.txt --post-data="username=USERNAME&password=PASSWORD" http://localhost:8000/api/login But the content of my_cookies.txt is: # HTTP cookie file. # Generated by Wget on 2012-06-23 22:31:33. # Edit at your own risk. When I run the same command but in debug mode I get the following output that includes the set cookie in the header response: DEBUG output created by Wget 1.10.2 (Red Hat modified) on linux-gnueabi. --22:31:11-- http://localhost:8000/api/login Resolving localhost... 127.0.0.1 Caching localhost => 127.0.0.1 Connecting to localhost|127.0.0.1|:8000... connected. Created socket 3. Releasing 0x000504d0 (new refcount 1). ---request begin--- POST /api/login HTTP/1.0 User-Agent: Wget/1.10.2 (Red Hat modified) Accept: */* Host: localhost:8000 Connection: Keep-Alive Content-Type: application/x-www-form-urlencoded Content-Length: 32 ---request end--- [POST data: username=USERNAME&password=PASSWORD] HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Content-Length: 34 Content-Type: application/json Cache-Control: no-cache, must-revalidate Set-cookie: beaker.session.id=405390ddc809efed54820638c95d7997; expires=Tue, 19-Jan-2038 04:14:07 GMT; Path=/ Connection: Keep-Alive Date: Sat, 23 Jun 2012 21:31:11 GMT Server: CherryPy/3.1.2 WSGI Server ---response end--- 200 OK hs->local_file is: login (not existing) Registered socket 3 for persistent reuse. TEXTHTML is on. Length: 34 [application/json] Saving to: `login' 100%[=======================================>] 34 --.-K/s in 0s 22:31:11 (1.28 MB/s) - `login' saved [34/34] Removing file due to --delete-after in main(): Removing login. Saving cookies to my_cookies.txt. Done saving cookies. Can anyone tell me what am I doing wrong? Thanks in advance!

    Read the article

  • Using virtualization infrastructure for J2EE application distribution- viable alternative?

    - by Dan
    Our company builds custom J2EE web solutions. At the moment, we use standard J2EE distribution mechanisms (ear/war archives). Application servers are generally administered by our clients' IT departments and since we do not have complete control over the environment, a lot of entropy can be introduced into the solution. For example: latest app. server patch not applied conflicting third party libraries inside the app. server root server runtime and tuning parameters not configured (for example, number of connections in database pool) We are looking into using virtualization infrastructure for J2EE application distribution. Instead of sending the ear/war archive, we’d send image with application server node and our application preinstalled. Some of the benefits are same as using with using virtualization infrastructure in general, namely better use of hardware resources. For us, it reduces the entropy of hosting infrastructure - distributing VM should be less affected by hosting environment. So far, the downside I see can be in application server licenses, here they will have to use dedicated servers for our solution, but this is generally already done that way. Also, there is a complexity with maintaining virtualization infrastructure, but this is often something IT departments have more experience with than with administering and fine-tuning J2EE solutions. Anyone has experience with this model? What are the downsides? Will we not just replace one type of complexity with other?

    Read the article

  • Unable to receive emails from Ubuntu postfix mail server

    - by Paddington
    I am unable to receive emails on an Ubuntu 11.04 server running postfix with the Plesk control panel. I can't see the mails even on webmail. I am able to send emails and am not getting any error messages on the email client when I try to receive. Here is the output of the logs: *tail -f /usr/local/psa/var/log/maillog Aug 29 10:38:31 cp9 postfix/tlsmgr[3811]: fatal: open database /var/lib/postfix/smtpd_scache.db: Invalid argument Aug 29 10:38:32 cp9 postfix/master[27738]: warning: process /usr/lib/postfix/tlsmgr pid 3811 exit status 1 Aug 29 10:38:32 cp9 postfix/master[27738]: warning: /usr/lib/postfix/tlsmgr: bad command startup -- throttling Aug 29 10:38:36 cp9 pop3d: Connection, ip=[::ffff:196.201.7.158] Aug 29 10:38:36 cp9 pop3d: IMAP connect from @ [::ffff:196.201.7.158]INFO: LOGIN, [email protected], ip=[::ffff:196.201.7.158] Aug 29 10:38:37 cp9 pop3d: 1346229517.874008 LOGOUT, [email protected], ip=[::ffff:196.201.7.158], top=0, retr=0, time=1, rcvd=24, sent=1716, maildir=/var/qmail/mailnames/essentialhuku.co.za/earle/Maildir Aug 29 10:14:05 cp9 postfix/tlsmgr[1133]: fatal: open database /var/lib/postfix/smtpd_scache.db: Invalid argument Aug 29 10:14:06 cp9 postfix/master[27738]: warning: process /usr/lib/postfix/tlsmgr pid 1133 exit status 1 Aug 29 10:14:06 cp9 postfix/master[27738]: warning: /usr/lib/postfix/tlsmgr: bad command startup -- throttling Aug 29 10:14:08 cp9 pop3d: Connection, ip=[::ffff:196.201.7.158

    Read the article

  • Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

    - by Johan Allgoth
    I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

    Read the article

  • Certain Japanese characters aren't displayed properly

    - by Nisto
    On the following site: http://www.nciku.com/search/radical the first 2 characters on the second row of the "Step 2" table aren't displayed properly. All other characters look fine. I tried re-installing the Asian fonts via the checkboxes regarding Asian fonts in the "Regional and Language Options" control panel applet. I have tried removing every single Font from the Fonts folder (some were ofcourse not possible to remove), and re-installing them all again. I did this by... Running cmd Closing down the explorer process In cmd; using the command DEL /F /S /Q * in the Fonts folder Putting in my XP SP3 Retail disc In cmd; using expand -r *.tt_ in the I386 folder on the XP disc (and any other font file, in the I386\LANG folder) I also tried installing this pack from Microsoft, but this solved nothing either. I even tried running my browser (Firefox) through AppLocale. And changing character encoding -- again, does not help. I've also tried viewing the page in Internet Explorer. What could be wrong? I have checked my Fonts folder, to make sure that every single font available on the XP disc is available in WINDOWS\Fonts. What shows in the first square on the second row - I can't really tell what it's supposed to look like (but it's not the proper character)... but the second square shows a rectangular symbol containing HEX code. I've been in this situation before -- and it has been when I've been missing fonts. But how could I possibly be missing a necessary font? Shouldn't it be provided in the Asian "font packages"? I've talked to some other users that has viewed the page, and they had no problems displaying those characters on second row - even though they're only using the fonts provided on the Windows installation disc. Windows XP Professional Service Pack 3 (x86 - with latest updates) Firefox 3.6.15

    Read the article

  • Multiple LDAP servers with mod_authn_alias: failover not working when the first LDAP is down?

    - by quanta
    I've been trying to setup redundant LDAP servers with Apache 2.2.3. /etc/httpd/conf.d/authn_alias.conf <AuthnProviderAlias ldap master> AuthLDAPURL ldap://192.168.5.148:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> <AuthnProviderAlias ldap slave> AuthLDAPURL ldap://192.168.5.199:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> /etc/httpd/conf.d/authz_ldap.conf # # mod_authz_ldap can be used to implement access control and # authenticate users against an LDAP database. # LoadModule authz_ldap_module modules/mod_authz_ldap.so <IfModule mod_authz_ldap.c> <Location /> AuthBasicProvider master slave AuthzLDAPAuthoritative Off AuthType Basic AuthName "Authorization required" AuthzLDAPMemberKey member AuthUserFile /home/setup/svn/auth-conf AuthzLDAPSetGroupAuth user require valid-user AuthzLDAPLogLevel error </Location> </IfModule> If I understand correctly, mod_authz_ldap will try to search users in the second LDAP if the first server is down or OpenLDAP on it is not running. But in practice, it does not happen. Tested by stopping LDAP on the master, I get the "500 Internal Server Error" when accessing to the Subversion repository. The error_log shows: [11061] auth_ldap authenticate: user quanta authentication failed; URI / [LDAP: ldap_simple_bind_s() failed][Can't contact LDAP server] Did I misunderstand? AuthBasicProvider ldap1 ldap2 only means that if mod_authz_ldap can't find the user in ldap1, it will continue with ldap2. It doesn't include the failover feature (ldap1 must be running and working fine)?

    Read the article

  • RAID administration in Debian Lenny

    - by Siim K
    I've got an old box that I don't want to scrap yet because it's got a nice working 5-disk RAID assembly. I want to create 2 arrays: RAID 1 with 2 disks and RAID 5 with the other 3 disks. The RAID card is Intel SRCU31L. I can create the RAID 1 volume in the console that you access with Ctrl+C at startup. But it only allows for creation of one volume so I can't do anything with the 3 remaining disks. I installed Debian Lenny on the RAID 1 volume and it worked out nicely. What utilites could I now use to create/manage the RAID volumes in Debian Linux? I installed the raidutils package but get an error when trying to fetch a list: #raidutil -L controller or #raidutil -L physical # raidutil -L controller osdOpenEngine : 11/08/110-18:16:08 Fatal error, no active controller device files found. Engine connect failed: Open What could I try to get this thing working? Can you suggest any other tools? Command #lspci -vv gives me this about the controller: 00:06.1 I2O: Intel Corporation Integrated RAID (rev 02) (prog-if 01) Subsystem: Intel Corporation Device 0001 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step ping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: Memory at f9800000 (32-bit, prefetchable) [size=8M] [virtual] Expansion ROM at 30020000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: PCI_I2O Kernel modules: i2o_core

    Read the article

  • NAT confusion regarding cisco ASA5510

    - by LonelyLonelyNetworkN00b
    I'm setting up my first cisco firewalls. A little information first:I have two asa5510 setup in a working active/standby pair. From my ISP i have two public subnets. A /29 and a /26. On my DMZ interface i have the /26 configured. On my WAN Interface i have configured the /29 IPs. My isp routes the /26 via the /29 primary IP. I'm running ASA 8.2. I've turned NAT-Control off, because i don't want to use nat for for other than some internal interfaces. In essence i don't want to use NAT unless i specify it. I have a internal interface with the network of 192.168.100.0/24. I've tried setting up nat limke this: nat (inside) 1 192.168.100.0 255.255.255.0 global (WAN) 1 interface I was under the impression that this would let connections that was going from 192.168.100.0/24 and out the WAN interface to be Port-Address-translated. I'm not getting this to work for some reason. Inside interface has security level of 100, and wan has security level of 0.

    Read the article

  • Desktop bigger than screen

    - by alex
    I am using MSI U115 11" netbook (OS: Windows XP Home, graphics card: Intel Graphics Media Accelerator 500) and today after I switched it on, desktop was bigger than screen. To be exact: screen resolution was set to the lowest possible and I could move mouse outside of screen (but only below - left, right and up worked normally, mouse could not exceed screen boundaries). I changed resolution back to normal, but the problem with desktop being bigger than screen remained (as before, only lower part - cannot see task bar, etc. When I hit windows button on keyboard, only upper part of menu start is visible). What I already tried was changing all kind of graphics and screen settings - none of them helped. I also tried to restore the system to few days before, but it didn't help neither. What can I do to make the desktop look "normally"? EDIT: Some additional info regarding screen: Sorry it's in polish - but let me explain. There are two screens I can choose (Monitor domyslny means default screen), but the second one (the default one) is not available. After I choose it and click apply number 1. is used (and as you can see it has only two resolutions available. There are more in the second one - but without 1024x600 though). The two ticked and grayed out options here are Use this screen as the main one and Enlarge Windows desktop to match this monitor's size. Too bad I cannot change them. When I choose the second screen, the first box is unchecked and grayed out. The second box is available to be changed but it doesn't matter anyway as after applying changes it reverts to the first screen anyway. EDIT: Intel Graphics Media Control Panel screenshot.

    Read the article

  • Debian: What are these files in /sys/devices/pci0000:00/ for?

    - by muhuk
    I am running Debian Squeeze on an MSI M670 laptop. I have these following files on my root drive, each 256MB: file:///sys/devices/pci0000:00/0000:00:05.0/resource1 file:///sys/devices/pci0000:00/0000:00:05.0/resource1_wc Here is my lspci output: muhuk@debian:~$ lspci 00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2) 00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: nVidia Corporation C51 [GeForce Go 6100] (rev a2) 00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3) 00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 04:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 04:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 04:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 04:09.0 Network controller: RaLink RT2561/RT61 rev B 802.11g I am speculating these have something to do with the shared RAM my GPU is using. But why a file on disk? And why two of them?

    Read the article

  • FTP not listing directory NcFTP PASV

    - by Jacob Talbot
    I am attempting to setup Multicraft on my server, all is running smoothly however the FTP won't allow anyone to connect from a remote FTP client, where net2ftp will work smoothly from a remote location. I have included the transcript from my FTP client, Transmit below to give you an idea of what's going on. I have disabled iptables as well, and still no luck either way. Transmit 4.1.7 (x86_64) Session Transcript [Version 10.8.2 (Build 12C54)] (21/10/12 11:23 PM) LibNcFTP 3.2.3 (July 23, 2009) compiled for UNIX 220: Multicraft 1.7.1 FTP server Connected to ateam.bn-mc.net. Cmd: USER jacob.9 331: Username ok, send password. Cmd: PASS xxxxxxxx 230: Login successful Cmd: TYPE A 200: Type set to: ASCII. Logged in to ateam.bn-mc.net as jacob.9. Cmd: SYST 215: UNIX Type: L8 Cmd: FEAT 211: Features supported: EPRT EPSV MDTM MLSD MLST type*;perm*;size*;modify*;unique*;unix.mode;unix.uid;unix.gid; REST STREAM SIZE TVFS UTF8 End FEAT. Cmd: OPTS UTF8 ON 200: OK Cmd: PWD 257: "/" is the current directory. Cmd: PASV Could not read reply from control connection -- timed out. (SReadline 1)

    Read the article

  • How can I set the CD audio volume in Linux?

    - by user1296362
    In Windows 7 Control Panel - Sound - Sound Properties window there's an slider for setting CD Audio volume: And it's pretty strange that I can't find corresponding one in generic Linux mixers: alsamixer or amixer. I connected a CD drive to try to set CD audio volume with cdcd (CD Player): $ cdcd setvol 0 Invalid volume It isn't actually an invalid volume, it is because ioctl() call fails. I found that out after searching and changing a bit the source code of this utility (in the libcdaudio): --- cdaudio.c.orig 2004-09-09 06:26:20.000000000 +0600 +++ cdaudio.c 2012-05-30 21:34:34.167915521 +0600 @@ -578,8 +578,10 @@ cdvol_data.CDVOLCTRL_BACK_RIGHT_SELECT = CDAUDIO_MAX_VOLUME; #endif - if(ioctl(cd_desc, CDAUDIO_SET_VOLUME, &cdvol) < 0) - return -1; + if(ioctl(cd_desc, CDAUDIO_SET_VOLUME, &cdvol) < 0) { + printf("*** cd_set_volume: ioctl() returned error\n"); + return -1; + } return 0; } By the way cdcd's get volume command yields rather weird output: Left Right Front 1281734864 32767 Back 0 0 Also I tried aumix: $ aumix -c 0 But all with no success. I read from this manual — http://tldp.org/HOWTO/Alsa-sound-6.html (section 6.2 The mixer) that CD channel can present in amixer output. Maybe some drivers for sound card are missing in my Ubuntu 12.04 LTS installation. Though I don't think it's the case: $ lsmod | grep snd snd_mixer_oss 22602 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 223867 1 snd_hda_intel 33773 4 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 19 snd_mixer_oss,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep ,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm All I need is just mute or set to 0 volume level of CD Audio channel, like I did in Windows 7, to get rid of sibilant noise in the speakers.

    Read the article

  • Mac computers unable to connect to samba

    - by tan-ce
    I have a Ubuntu 9 server with samba 3.3 installed. This server has two network interfaces, one to a "public network" which I do not have any control over and another to a private LAN. On the private LAN, samba is the Domain Controller and nmbd is the WINS server on that network. On the "public network", I have configured a second instance of nmbd to run as a WINS client. The setup seems to work fine for Windows XP (on the domain or otherwise) as well as other Ubuntu machines. Finally, my question: Mac computers seem unable to connect to the samba server. As far as I can tell, it is as if samba is invisible to the MAC computer. Could my configuration of nmbd be causing this problem? Or is this simple a Mac oddity and is there anything I can do about it? New updates/info: We tried to connect through the Finder - Connect to Server, we entered smb://servername where servername is the netbios and DNS name. (There is also a DNS entry for the same name on the network) We also tried connecting by IP address Also, I just realized that there is at least one Mac which can connect. (Leopard 10.5.8) I will try to get the Mac OS versions of the computers which couldn't connect as soon as I can. The Mac which could not connect was running Mac OS X 10.4.11. Was there a change to samba on Mac OS between 10.4 and 10.5?

    Read the article

  • can't connect to vsftpd from outside network

    - by rick
    i know this has been asked many times before, but nothing seems to resolve my issue. i have vsftpd running on ubuntu 10.04. i can connect with ftp localhost on the machine. i can connect from another machine in my network. i just cannot connect from outside. the machine is behind an airport extreme managed by airport utility on a mac. 21 is open as per nmap: macmini:~$ nmap localhost Starting Nmap 5.21 ( http://nmap.org ) at 2011-04-10 23:49 EDT Nmap scan report for localhost (127.0.0.1) Host is up (0.00045s latency). Hostname localhost resolves to 2 IPs. Only scanned 127.0.0.1 rDNS record for 127.0.0.1: localhost.localdomain Not shown: 997 closed ports PORT STATE SERVICE 21/tcp open ftp 22/tcp open ssh 631/tcp open ipp netstat says 21 is listening: macmini:~$ netstat -lep --tcp | grep ftp (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) tcp 0 0 *:ftp *:* LISTEN iptables: macmini:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination when i try to connect from my external IP (or a dyndns name which resolves there) it times out. ("control connection timed out") as i know very little about networking, i feel like something may jump out as clearly wrong?

    Read the article

  • Compiling PHP with GD and libjpeg support

    - by Robin Winslow
    I compile my own PHP, partly to learn more about how PHP is put together, and partly because I'm always finding I need modules that aren't available by default, and this way I have control over that. My problem is that I can't get JPEG support in PHP. Using CentOS 5.6. Here are my configuration options when compiling PHP 5.3.8: './configure' '--enable-fpm' '--enable-mbstring' '--with-mysql' '--with-mysqli' '--with-gd' '--with-curl' '--with-mcrypt' '--with-zlib' '--with-pear' '--with-gmp' '--with-xsl' '--enable-zip' '--disable-fileinfo' '--with-jpeg-dir=/usr/lib/' The ./configure output says: checking for GD support... yes checking for the location of libjpeg... no checking for the location of libpng... no checking for the location of libXpm... no And then we can see that GD is installed, but that JPEG support isn't there: # php -r 'print_r(gd_info());' Array ( [GD Version] => bundled (2.0.34 compatible) [FreeType Support] => [T1Lib Support] => [GIF Read Support] => 1 [GIF Create Support] => 1 [JPEG Support] => [PNG Support] => 1 [WBMP Support] => 1 [XPM Support] => [XBM Support] => 1 [JIS-mapped Japanese Font Support] => ) I know that PHP needs to be able to find libjpeg, and it obviously can't find a version it's happy with. I would have thought /usr/lib/libjpeg.so or /usr/lib/libjpeg.so.62 would be what it needs, but I supplied it with the correct lib directory (--with-jpeg-dir=/usr/lib/) and it doesn't pick them up so I guess they can't be the right versions. rpm says libjpeg is installed. Should I yum remove and reinstall it, and all it's dependent packages? Might that fix the problem? Here's a paste bin with a collection of hopefully useful system information: http://pastebin.com/ied0kPR6

    Read the article

  • Setting up MongoDB in High Performance Computing LSF linux cluster

    - by Dnaiel
    I am trying to run mongo in a LSF cluster computing environment where I have no admin control. Our sysadmin installed mongodb, but it is not running. Any ideas on what should I ask the server admin to do for it to run? Or if I could run it locally? [node1382]allelix> mongod --dbpath /users/dnaiel/ma/mongodb/ Tue Oct 2 21:33:48 [initandlisten] MongoDB starting : pid=22436 port=27017 dbpath=/seq/epigenome01/allelix/ma/mongodb/ 64-bit host=node1382 Tue Oct 2 21:33:48 [initandlisten] Tue Oct 2 21:33:48 [initandlisten] ** WARNING: You are running on a NUMA machine. Tue Oct 2 21:33:48 [initandlisten] ** We suggest launching mongod like this to avoid performance problems: Tue Oct 2 21:33:48 [initandlisten] ** numactl --interleave=all mongod [other options] Tue Oct 2 21:33:48 [initandlisten] Tue Oct 2 21:33:48 [initandlisten] db version v2.2.0, pdfile version 4.5 Tue Oct 2 21:33:48 [initandlisten] git version: f5e83eae9cfbec7fb7a071321928f00d1b0c5207 Tue Oct 2 21:33:48 [initandlisten] build info: Linux ip-10-2-29-40 2.6.21.7-2.ec2.v1.2.fc8xen #1 SMP Fri Nov 20 17:48:28 EST 2009 x86_64 BOOST_LIB_VERSION=1_49 Tue Oct 2 21:33:48 [initandlisten] options: { dbpath: "/users/dnaiel/ma/mongodb/" } Tue Oct 2 21:33:48 [initandlisten] journal dir=users/dnaiel/ma/mongodb/journal Tue Oct 2 21:33:48 [initandlisten] recover begin Tue Oct 2 21:33:48 [initandlisten] info no lsn file in journal/ directory Tue Oct 2 21:33:48 [initandlisten] recover lsn: 0 Tue Oct 2 21:33:48 [initandlisten] recover /seq/epigenome01/allelix/ma/mongodb/journal/j._0 Tue Oct 2 21:33:48 [initandlisten] recover cleaning up Tue Oct 2 21:33:48 [initandlisten] removeJournalFiles Tue Oct 2 21:33:48 [initandlisten] recover done Tue Oct 2 21:33:48 [websvr] admin web console waiting for connections on port 28017 Tue Oct 2 21:33:48 [initandlisten] waiting for connections on port 27017 It basically waits forever and cannot start mongodb. These servers are not webservers but they do have network access, it's a cloud computing LSF environment system. Any advice would be welcome, thanks in advance.

    Read the article

  • Scheduling Automatic Backups for Virtual Private Web Server running CENTOS 6.3 and WHM

    - by Oliver Farrell
    I'm pretty new to administering my own VPS - but thus far am finding it quite a compelling experience. There's something quite refreshing about having complete control over everything it does. One thing that I would like to look at is a suitable backup solution (a few times a day). My current setup is as follows: I'm running a CENTOS 6.3 VPS with a single 25GB hard drive solely for the purpose of hosting websites. I'm using WHM & cPanel for administering them. I now plan on adding an additional hard disk and hooking it up to my VPS. What I'm not sure about is how I get the two disks talking and get the backup process going. I'm not a seasons SSH-er so don't really know where to start. I'm hosting with Serverlove (one of the best hosting providers I've used) and am provided with a number of unique identifiers for each hard disk so I imagine these may play a part in linking them together. I appreciate that this is a little vague (I'm clutching at straws) but any assistance is very much appreciated.

    Read the article

  • how to prevent other computers from seeing our network computers through vpn

    - by Disco
    We have a local office domain consisting of Windows 7 and XP machines that is running on Windows Server 2008 R2. We also have users that connect via VPN into our network. My concern is that when a remote user opens up a folder, the Network section on the left side of the folder shows the remote user all the computer names in our local network. I would like to go about renaming our computers in the local network with more descriptive computer names, but I do not want the users off-site to be able to see these computer names by simply opening up a folder. (Granted, they can already do this, but our current naming scheme does not link computer names to users.) I would like to change our computer names so we can determine which computer belongs to which user more easily IF it can be done securely. How can I ensure that our local computer names are not showing up in the Network folder for remote, VPN-connected users? My online searches have turned up results where people are advised to turn off Network Sharing and Discovery, but that seems to only ensure that the local machine doesn't see other computer names. I want to prevent OUR computer names from showing up on OTHER computers, and I can't go into the VPN-connected computers and turn off THEIR Network Discovery settings. I would think there is a group policy that would control this but I have not found one yet and I don't know how I would apply it to VPN-connected computers. Thanks! EDIT: That's true, a Group Policy wouldn't run on users only connecting via VPN, good point. What about a VPN/router policy, then?

    Read the article

  • Windows Server 2008 R2 - VPN Folder Sharing Permissions

    - by daveywc
    I have setup VPN access to my Windows Server 2008 R2 server using RRAS. Clients can connect, run applications, view shares etc. My problem is that one of the applications that they use relies on some network shares. The application is not able to access the shares unless the user first goes into Windows Explorer and accesses the share, providing their user name and password (the same one that they use to connect via the VPN). Previously on a different Windows Server 2008 (not R2) this was not necessary i.e. the application and user could access the share without providing another user name and password. I have tried giving the Everyone group full control over the shared folder - both on the Security tab and in the Permissions area under Advanced Sharing on the Sharing tab. This still did not resolve the issue. (I don't really want to give Everyone access anyway - I was hoping that granting access to a group that the VPN users had membership of would be enough). I have also turned off password protected sharing in the Advanced Sharing Settings area of the Network and Sharing Center (under both Home or Work and Public). So my question is what is preventing my VPN users from having access to these folders without having to re-supply the same login and password that they use to access the VPN? And what is the best practice in this type of scenario?

    Read the article

  • Sending email with exim and extrnal sender address

    - by Tronic
    hi. i have following problem: i want to send emails with an rails webapp. i set up an exim server and when looking into the logs, the sending works, but the emails aren't sent really. i had the same problem with another isp. the sender address is hosted on another mailserver, other isp. i think the problem is, that sending doesn't work because the sener address isn't hosted on the same server. do you have any advice on this? the logs (exim) tell me the following: 2011-01-01 14:38:06 1PZ1eo-0000Ga-38 <= <> R=1PZ1eo-0000GY-1p U=Debian-exim P=local S=1778 2011-01-01 14:38:08 1PZ1eo-0000Ga-38 => [email protected] R=dnslookup T=remote_smtp H=mx1.emailsrvr.com [98.129.184.131] X=TLS1.0:RSA_AES_256_CBC_SHA1:32 DN="C=US,O=mx1.emailsrvr.com,OU=GT21850092,OU=See www.geotrust.com/resources/cps (c)08,OU=Domain Control Validated - QuickSSL(R),CN=mx1.emailsrvr.com" 2011-01-01 14:38:08 1PZ1eo-0000Ga-38 Completed [email protected] is the external sender-address! thank you!

    Read the article

< Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >