Search Results

Search found 2043 results on 82 pages for 'collision detection'.

Page 68/82 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• Why does ATI 5570 HD video card driver installation cause Windows 7 To Blue Screen?

  - by Mort

  This one is for the hive mind. I have a brand new Dell Optiplex 760 workstation with 4 gigabytes of RAM running Windows 7 Professional (32bit). This is a new box with nothing installed other than what was provided for directly by Dell. I installed a Saphire ATI PCI Express 5570 HD. Upon trying to install the 10.4 Catalyst drivers the system will blue screen. It blue screens during the hardware detection phase of the installation process. I have already performed the following trouble shooting steps: Changed system RAM Installed only 2 gigabytes of RAM Installed different versions of Catalyst drivers (10.4 - 9.12) Tried to install video only component of driver (vs entire Catalyst suite) Made sure Windows 7 was fully updated Flashed mother board BIOS to current version Removed and re-seated video card Contacted ATI Support (We all know how this went......) Verified supply outputting properly The blue screen error (via Windows BugCheck entry in event log) is a 0x000000CA and refers to a plug and play error most likely caused by a bad driver. The problem is that the driver installation process never gets far enough to actually install a driver. The resolution center in Windows provides a solution of installing the 10.4 Catalyst driver to resolve issue (which fails). Looking for some alternate views to resolve.

  Read the article

• Azure load-balancing strategy

  - by growse

  I'm currently building out a small web deployment using VM instances on MS Azure. The main problem I'm facing at the moment is trying to figure out how to get the load-balancing to detect if a particular VM has failed and not route traffic to that VM. As far as I can tell, there are only only two load-balancing options: Have multiple VMs (web01, web02, web03 etc.) within the same 'cloud service' behind a single VIP, and configure the endpoints to be load balanced. Create multiple 'cloud services', put a single web VM in each and create a traffic manager service across all these services. It appears that (1) is extremely simplistic and doesn't attempt to do any host failure detection. (2) appears to be much more varied, but requires me to put all my webservers in their own individual cloud service. Traffic manager appears to be much more directed at a geographic failover scenario, where you have multiple cloud services across different regions. This approach also has the disadvantage in that my web servers won't be able to communicate with my databases on internal IP addresses, unlike scenario (1). What's the best approach here?

  Read the article

• Load Testing a Security/Gateway Appliance

  - by Joel Coel

  In a couple weeks I will load testing a security/gateway appliance. We're a small residential college, and that "residential" means the traffic moving through the appliance is a bit like the Wild West. We have everything from Facebook to World of Warcraft, BitTorrent to Netflix, or Halo to YouTube... basically anything you might find in the home of a high-school or college aged person. Somewhere in there some real academic work gets done as well. We rely on our current appliance for traffic shaping, antivirus, malware filtering, intrusion detection on our servers, logging and abuse reporting, and even some content filtering. All this puts a decent load when we have students around, and I'm concerned about the ability of the new candidate to keep up. On paper it should handle things, but I'm worried. Prior experience is that vendors greatly over-report what an appliance can handle. The product also includes a licensed session limit, and I'm also worried that just a few misbehaving students could unwittingly bring us to that limit and cause service disruptions. I need to know this will work for our campus in order to commit to it. Going a performance level higher in that product takes the pricing way out of line with what we expect and have done in the past. What I need is a good way to load test this guy. My problem is that our current level of summer traffic is less than one percent of what it will be when students come back just six weeks from now. Any ideas on how to really stress this thing and see what it can do, in a way that will give me some clear ideas o. How that will scale for our campus? For the curious, I'm looking at a Watchguard 515, but it could be anything. If I were evaluating a competitor, I'd ask the same question.

  Read the article

• PostgreSQL failover cluster on Windows Server

  - by user36997

  We are looking for advice on how to setup a basic failover cluster for our application: We will be using 4 machines running Microsoft Windows Server (most probably 2003). All four will always run our application, which is essentially a web service. Load balancing is "outsourced" - somebody else handles the distribution of the web requests among the servers. Only one of the servers will be running the PostgreSQL server actively at any given time. Another server (of the four) also has the DB installed, but is on standby/passive. The DB data is stored on shared storage. No copying data between servers. Reads are done very frequently by many end-users, and in rather small chunks of data. Writes are done much less frequently, by less users, and in very large bulks of data. Now, how can one configure Microsoft Cluster Service to keep only one instance of the DB server and 4 instances (1 per server) of our application at all times? And does PostgreSQL integrate neatly with MSCS at all? Update: Instead of keeping the data on shared storage, I also consider using log shipping to replicate data on a couple of DB servers. There are two issues with this option: Log shipping only makes sure that I have a second server that gets all of the data and is ready to take over. How do I implement the actual failure detection and failover switch? Switching back: Suppose the master fails and the system automatically fails over to the slave, and later the master comes back online. I understand that with WAL shipping this will require to reconfigure the log shipping once again, and that switching back is far from seamless. Is that so?

  Read the article

• Accidentally mounted a ReiserFS drive as MBR on my windows box - how do I recover?

  - by Ryan

  I had a WD Netcenter with a 160GB drive that kept dropping off the network. I opened up the enclosure and removed the hard drive, connected to a Windows box without knowing the drive used ReiserFS.... When mounting on the Windows box, I chose "MBR" as filesystem. 70GB of data corrupted: 90% of data is word documents, excel spreadsheets, and jpg's - all mission critical. Attempted recovery on Linux box (ubuntu) using TestDisk: I could see the container, but couldn't get anything out – according to TestDisk this was because I chose "none" as filesystem. Attempted recovery using Nucleus Kernel Recovery for windows: 98% of what was recovered is incomplete and/or unusable. I need to know if a way exists to recover or rebuild original ReiserFS MBR, or what tools/techniques might give me the best results in recovering the data. Found a Windows version of TestDisk and I ran it yesterday - here are the results: TestDisk 6.14-WIP, Data Recovery Utility, May 2012 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sda - 160 GB / 149 GiB - CHS 19457 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 519 GB / 483 GiB) Check the harddisk size: HD jumpers settings, BIOS detection... The following partitions can't be recovered: Partition Start End Size in sectors > ReiserFS 3.6 62 241 8 19458 0 18 311581568 ReiserFS 3.6 62 248 55 19458 8 2 311581568 ReiserFS 3.6 62 254 37 19458 13 47 311581568 ReiserFS 3.6 63 6 28 19458 20 38 311581568 ReiserFS 3.6 63 13 11 19458 27 21 311581568 ReiserFS 3.6 63 21 43 19458 35 53 311581568 ReiserFS 3.6 63 27 41 19458 41 51 311581568 ReiserFS 3.6 63 37 35 19458 51 45 311581568 ReiserFS 3.6 63 54 20 19458 68 30 311581568 ReiserFS 3.6 63 76 26 19458 90 36 311581568

  Read the article

• Increasing Java's heapspace in Tomcat startup script

  - by Ankur

  I want to increase my heap size when using Tomcat. I was told to add this line export CATALINA_OPTS=-Xms16m -Xmx256m; In to the startup.sh script - I did so (at the beginning) but got the error export: 24: -Xmx256m: bad variable name Where am I supposed to add it, am I doing something else wrong? <b>export CATALINA_OPTS=-Xms16m -Xmx256m;</b> # Better OS/400 detection: see Bugzilla 31132 os400=false darwin=false case "`uname`" in CYGWIN*) cygwin=true;; OS400*) os400=true;; Darwin*) darwin=true;; esac # resolve links - $0 may be a softlink PRG="$0" while [ -h "$PRG" ] ; do ls=`ls -ld "$PRG"` link=`expr "$ls" : '.*-> \(.*\)$'` if expr "$link" : '/.*' > /dev/null; then PRG="$link" else PRG=`dirname "$PRG"`/"$link" fi done PRGDIR=`dirname "$PRG"` EXECUTABLE=catalina.sh # Check that target executable exists if $os400; then # -x will Only work on the os400 if the files are: # 1. owned by the user # 2. owned by the PRIMARY group of the user # this will not work if the user belongs in secondary groups eval else if [ ! -x "$PRGDIR"/"$EXECUTABLE" ]; then echo "Cannot find $PRGDIR/$EXECUTABLE" echo "This file is needed to run this program" exit 1 fi fi exec "$PRGDIR"/"$EXECUTABLE" start "$@"

  Read the article

• How can I fix my vista PCs screen resolution and refresh rate

  - by Antony Scott

  I have a media PC running media portal hooked up to my HDTV via HDMI. The TV is a couple of years old now, so only supports 1080i, which is 1920x1080@25Hz. I've got it connected to my PC via a HDMI compatible AV receiver. If I power up the amp (wait for it to boot fully) followed by the TV| and finally the PC, all is well and I get a picture. If I deviate from that sequence, or don't wait for the amp to book up fully, or even switch the amp to another video input (for example, my PS3). The PC sees this and defaults the screen resolution/refresh rate to 1920x1080@60Hz. So, I end up with a blank screen. To fix this I have to use UltraVNC from a PC and change the refresh rate back to 25Hz. So, is there a way to turn off that auto detection, or to manually define what resolution/refresh rates the monitor can do. I'm using the on-board Radeon 3200 video and do not have any of the AMD software installed as it seems to cause problems with video playback. So, I'm looking for a native vista fix, or possible some 3rd party software.

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• How can I fix video tearing and pausing on Windows XP Flash videos?

  - by xvs

  I have what should be a reasonably fast PC: it's a Quadcore Intel 6600 at 2.4 GHz, 4MB of RAM, an ATI 3800 series video card and an LG L246WP monitor, which I selected particularly because it was supposed to work well with video and have no trails or other artifacts. So I should be able to play video with no problems. And I can, as long as that video isn't Flash video. With Flash, what I see is tearing, especially during pans, and pausing -- every few seconds the video pauses for about 300ms while the sound stays continuous. I tried going into the video card setup and changing vertical sync, pulldown detection, windows media video acceleration, deinterlacing and triple buffering. but no combination of settings I've tried has changed or corrected the problem in any way. I've also tried enabling and disabling hardware acceleration in the Flash settings, to no avail. This problem happens whether or not the video is streaming or has fully streamed in before playing. So, what can I do? Is this just a flash issue or is there a way to get it to work?

  Read the article

• Automated Scanning for Corrupted Archive Files

  - by Synetech inc.

  Hi, I have all kinds of files that I have downloaded from everywhere over the years scattered around my hard drives. I’m in the process of trying to organize them all and have run into a problem. Sometimes a file was not downloaded correctly (this was a big issue when Chromium first came out) and is thus corrupt. For media files, this is relatively simple to determine (it requires actually opening and examining the file). For executables or other binaries, it is relatively difficult (executables may or may not crash, other binaries could be completely unknown). Archive files (eg zip, rar, 7z, exe, ace, etc.) however should be pretty simple, they have a built-in corruption detection facility. My problem now is that I really don’t want to open and test each and every single archived file throughout my drive; that would be a nightmare. I’m looking for a utility that can automate the process. Is there a program that can scan archive files on a drive and list the ones that are corrupt? Thanks a lot.

  Read the article

• Libraries merged folder views

  - by Stigma

  So I pretty much love the Windows 7 Libraries feature, and saw one use for them that I thought would be perfect, but I can't seem to manage it. Basically, a merged view of different folder structures. Suppose I make a new generic library and add three locations to it: C:\Test\, D:\Test\ and D:\temp\Test\. Now, these may look somewhat okay as long as there are no duplicates in these folders. (It wants to group them based on the included directory, which one can work around by looking on google - I don't have the precise trick on hand I am afraid.) But when you get collisions and, say, two of those directories have a Sub directory in them, stuff becomes unusable (assuming Arrange by: Folder view). You'll have multiple folders listed named Sub, which is pretty useless when looking for data. I want folders to get 'merged', which ought to be possible somehow since it can create these merged views based on artist, album etc in other views. So all subdirectories that are double (and recursively checking for doubles inside those, etc) ought to be merged for as far the View is concerned. If files have a collision, I don't really care what happens - hide one, show both, filter out duplicates, whatever. (Although an option would be nice...) Anyhow, is there anyone who knows how to get such a 'merged folder structure' functionality for Libraries? It would be really useful for me.

  Read the article

• Motion - takes snapshot without motion detected

  - by Emmanuel Brunet

  I've been installed the standard motion 3.2.12 package on debian 7.5. I would like to get snapshot ONLY when motion is detected, but it still saves a picture every second without any activity in front of the camera. I'm using a TENVIS JPT3815W IP camera motion.conf here is my configuration file setup_mode off target_dir /media/videos/log/webcam netcam_url http://webcam/snapshot.cgi netcam_tolerant_check on netcam_userpass admin:alpha1237 # Output frames at 1 fps when no motion is detected and increase to the # rate given by webcam_maxrate when motion is detected (default: off) webcam_motion off output_all off # detection settings 1-255 default 32 noise_level 50 # Maximum framerate for webcam streams (default: 1) webcam_maxrate 25 pre_capture 0 framerate 25 gap 30 locate on mail [email protected] text_right "FRONT CAMERA %Y/%m/%d - %T" text_double on ffmpeg_cap_new on ffmpeg_cap_motion on ffmpeg_video_codec mpeg4 output_motion off snapshot_interval 0 # Quality of the jpeg (in percent) images produced (default: 50) quality 90 # Restrict webcam connections to localhost only (default: on) webcam_localhost off # Limits the number of images per connection (default: 0 = unlimited) # Number can be defined by multiplying actual webcam rate by desired number of seconds # Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate webcam_limit 0 Issue when I start motion images are stored in /media/videos/log/webcam nearly every second. I hjust want to get images when a motion is detected and the according video clip Any idea where the configuration fails ?

  Read the article

• Heartbeat/DRBD failover didn't work as expected. How do I make the failover more robust?

  - by Quinn Murphy

  I had a scenario where a DRBD-heartbeat set up had a failed node but did not failover. What happened was the primary node had locked up, but didn't go down directly (it was inaccessible via ssh or with the nfs mount, but it could be pinged). The desired behavior would have been to detect this and failover to the secondary node, but it appears that since the primary didn't go full down (there is a dedicated network connection from server to server), heartbeat's detection mechanism didn't pick up on that and therefore didn't failover. Has anyone seen this? Is there something that I need to configure to have more robust cluster failover? DRBD seems to otherwise work fine (had to resync when I rebooted the old primary), but without good failover, it's use is limited. heartbeat 3.0.4 drbd84 RHEL 6.1 We are not using Pacemaker nfs03 is the primary server in this setup, and nfs01 is the secondary. ha.cf # Hearbeat Logging logfacility daemon udpport 694 ucast eth0 192.168.10.47 ucast eth0 192.168.10.42 # Cluster members node nfs01.openair.com node nfs03.openair.com # Hearbeat communication timing. # Sets the triggers and pulse time for swapping over. keepalive 1 warntime 10 deadtime 30 initdead 120 #fail back automatically auto_failback on and here is the haresources file: nfs03.openair.com IPaddr::192.168.10.50/255.255.255.0/eth0 drbddisk::data Filesystem::/dev/drbd0::/data::ext4 nfs nfslock

  Read the article

• Apache, Tomcat and mod_jk for load balancing

  - by pHk

  Hi guys. I've set-up a basic Apache (2.2.x) and Tomcat (6.0.x) set-up using mod_jk for load balancing using the worker.properties file. Preliminary testing seems to show that this works relatively well, and it was quite easy to set-up. However; the fact that it was so easy to set-up has got me a little worried. We're dealing with 100 - 300 concurrent users using the same web application (deployed on 2 or 3 Tomcat instances). I have done a little Googling and looking around on here and there seems to be more than 1 way to accomplish this (one example on here used a balancer:// style URL, which I've never seen before in an Apache config). For example, one question I ask myself is how reliable the load detection on mod_jk really is (Busyness, Session, Request, etc). In your experience, does this set-up prove to be reliable in real world scenarios? Any pointers on improvements, pit falls or interesting literature/articles? I've worked with Apache before, but am in no way an expert. Thanks in advance.

  Read the article

• "A disk read error occurred" after choosing to boot into Windows XP from GRUB

  - by kellogs

  "A disk read error occurred" appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris Here, sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I cannot recall how exactly have I used testdisk but it once said: Disk /dev/sda - 160 GB / 149 GiB - CHS 19458 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 169 GB / 157 GiB) Check the harddisk size: HD jumper settings, BIOS detection... So far I have tried to "fixboot" and "chkdsk" from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please? Thank you!

  Read the article

• I'm looking for a program that can automate opening/closing a program

  - by Peterstone

  I am looking a for a program to remember things with these features: Open files or programs in my own computer at a planned time. For example I want every morming at 8:00 the program open a particular mp3 file. But suposse, by mistake, that I on my computer and 9:00, then I want that the program rememberme what I planned to open at 8:00. Show me the program as an active windows on my desktop. The windows of the program opened is what the user is seeing (Is at the first place in the desktop) and the rest of the program windows are below. Close programs or files in my own computer at a planned time. For example I want that the program mp3 file that was opened at 8:00 was closed at 10:00 if at that time still be opened. Detection of events. For instance If I open particular videogame program. then a mp3 file (with a recording message arguing why I shouldn´t continue playing that videogame at work time) is opened. Possibility of combine the features mentioned before each other.

  Read the article

• How can I get Windows 8 to automatically disable touch when I am using my Wacom pen and turn it back on when I am not

  - by Robert

  I have an HP convertible tablet computer which I just upgraded to Windows 8. The problem (which existed under Windows 7 as well) is that this tablet has both a capacitive touch screen (with multi-touch) AND a wacom-type tablet built in to the screen that works using electro-magnetic resonance with the provided stylus. My Use Case: Most of the time I am happy using my fingers and the touch interface for navigation and whatnot. However, when I want to get down to serious note-taking/drawing, I want to use the wacom functionality. The problem is that any comfortable writing position has me resting my arm/hand on the screen, which activates the touch technology (despite supposed palm-detection algorithms) and completely screws up my input paradigm. My Ideal Solution: Ideallly, since wacom technology senses when the pen is "close" to the screen, I would love to have touch be automatically disabled whenever the wacom pen is detected, and turned back on when it is out of range. this would allow me to seamless switch between the two input methods, and since I NEVER want to use both at once would work perfectly for me. An acceptable alternative: As a next best option, It would be great to be able to turn off the touch functionality (leaving the wacom in place) whenever I entered specific apps (e.g. OneNote, Photoshop, Gimp, Pencil, etc.) and then have it turn back on when I left that app.... As a worst case at least lets me use my PC option: If I could create a shortcut (tile or otherwise) that flips the touch on and off without going all the way through the nested computer settings, that would be better than nothing. Thanks in advance for the help with 1 or more of the above.

  Read the article

• "What happens?" server performance monitor

  - by AlexAtNet

  Hello! After reviewing some thread about server monitoring software I end up with a simple question: Which of the server monitoring tools should I use for automatic detection of "abnormal" situations with recommendations on how to fix them? I look for software that checks the system performance after installation and calculate some average load values (memory, CPU, etc). And when something happens (CPU load is increased to 20%) then it tries to detect a reason for this. If it is apache, it should check for access logs. If mysql, it should check mysql logs and tell me what happens. It this is because some user decodes a lot of images, I'd like to know which command is executed, when and user name. The same for disk usage, memory, number of processes, threads and so on. Ideally, this software should periodically checks the system and report problems: errors in PHP error log, outdated packages, security vulnerabilities. In other word I'm looking a software that will keep my simple Debian/Apache/PHP/MySQL server without forcing me to monitor the charts every day. I hope that such program exists. Thanks, Alex

  Read the article

• Server side url scanner for malware, spyware , viruses and protect my visitors

  - by Vangel

  I have a forum/groups site that contains a lot of external URLs, sometimes direct download links. I want to protect my visitors from possible attacks from malware sites as they are mot likely to click on these links. CUrrently I implement DBL (spamhaus) but thats not enough. I want to run a background task to check the outgoing links first. I have looked at similar questions in StackOverflow (wrongly posted there) and here but fail to find a question same as mine or a good answer. People have suggested ClamAV , I don't believe it can detect Web hosted malware sites and its has a lot of missed detection. I have looked at google safe browsing service ( http://code.google.com/apis/safebrowsing/developers_guide_v2.html very complicated to implement or maintain plus midway I get lost :S ) I can go for commercial solution, anything to protect the visitors and my site brand. But I would like to hear the opinion of server admins and if anyone has implemented such a service. My Server is basic CentOS LAMP stack. thank you very much in advance.

  Read the article

• I need a driver for my Cardbus USB 2.0 card

  - by Carl

  The picture and details of the card are here: http://www.ht-link.com/en/ProductView.asp?ID=106 The Windows drivers for this don't work right. I tried them on my previous laptop, and then installed the ones off their included CD. (Note that the systems requirements includes a CD-ROM drive...) I have a new laptop, and lost the CD. The website that lists the drivers is broken - the download links don't work. It is here: http://www.ht-link.com/en/DownView.asp?ID=10 I need the very first link - The Win XP drivers for the HT-112NEC. The company does not reply to my e-mails. I've tried searching Google for other sources for the driver (I didn't bother with those sites that want me to install driver detection software or create a log-in for their site). [Here's the problem I am getting using the drivers Windows XP SP3 installs: When I plug in my USB 2.0 hard-disk adapter, a USB Mass Storage Device entry is added in the Device Manager, but there is no entry under Disk Drives, and a drive letter is not assigned, so I can't access the driver. Like I said, this card didn't work without their special drivers on my other laptop, either.]

  Read the article

• EC2 AMI won't boot after edit

  - by Eric Lars0n

  I did something stupid, I got a new laptop and copied everything over to the new one, then wiped the old one clean. Then I realized that I forgot to copy the private key out of .ssh that I use to connect to my AWS EBS backed instance. So I can't log in to my custom AMI. So I created a new Volume from the Snapshot of the AMI, then started up a public instance and attached the Volume to it, edit the sshd_config to allow for password log in. Unmounted the volume, detached it, made a snapshot of it, then made a new AMI from the snapshot. The new AMI launches, but never passes the Status Checks and is not reachable. What am I doing wrong? Or alternatively how can I fix my problem? Edit: Adding some of the console output Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize NET: Registered protocol family 2 Registering block device major 8 XENBUS: Timeout connecting to devices! Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,0)

  Read the article

• Why does Windows/Microsoft Updates always take such a long time to detect available updates?

  - by RLH

  It's a common task for many of us who work in any form of IT position using Windows. Eventually you have to install/re-install a version of Windows and what follows is a very long OS updating process. For a long time I have accepted the fact that this is a slow process and that's all there is to it. There is a lot to download, and some updates require restarts followed by further updates... Ugh! This morning I had to go through the process of installing Windows XP with SP3. I'm installing the OS on a VM on an SSD and I've been working on this thing for over 6 hours. Although, think there are many ways to knit-pick this process for improvements, there is one step that is always particularly slow and I can not figure out a good reason why. That step is the detection step on a manual update. Specifically, when navigate to the Windows (or Microsoft) Updates page, and then click the 'Custom' button to detect your updates. It appears that your PC just sits there for a painful amount of time. Check your Task Manager and it looks like your PC is, in fact, locked because your CPU isn't cooking but that's certainly not the case. Somethings happening but I have no clue what's going on? What is the updating software doing? If the registry was being searched, shouldn't my CPU usage peak? Does anybody know what's happening? I can loosely justify why some of the steps in the update process take so long. However, this one doesn't seem to have any reasoning.

  Read the article

• Creating a partitioned raid1 array for booting a debian squeeze system

  - by gucki

  I'd like to have the following raid1 (mirror) setup: /dev/md0 consists of /dev/sda and /dev/sdb I created this raid1 device using mdadm --create --verbose /dev/md0 --auto=yes --level=1 --raid-devices=2 /dev/sda /dev/sdb This gave a warning about metadata being 1.2 and my system might not boot. I cannot use 0.9 because it restricts the size of the raid to 2TB and I assume grub shipped with latest debian (squeeze) should be able to handle metadata 1.2. So then I created the needed partitions like this: # creating new label (partition table) parted -s /dev/md0 mklabel 'msdos' # creating partitions sfdisk -uM /dev/md0 << EOF 0,4096 ,1024,S ; EOF # making root filesystem mkfs -t ext4 -L boot -m 0 /dev/md0p1 # making swap filesystem mkswap /dev/md0p2 # making data filesystem mkfs -t ext4 -L data /dev/md0p3 Then I mounted the root partition, copied a minimal debian install inside and temporary mounted /dev /proc /sys. Afer this I chrooted to the new root folder and executed: grub-install --no-floppy --recheck /dev/md0 However this fails badly with: /usr/sbin/grub-probe: error: unknown filesystem. Auto-detection of a filesystem of /dev/md0p1 failed. Please report this together with the output of "/usr/sbin/grub-probe --device-map=/boot/grub/device.map --target=fs -v /boot/grub" to I don't think it's a bug in grub (so I didn't report it yet) but a fault of mine. So I really wonder how to properly setup my raid1, everything I tried so far failed.

  Read the article

• dell latitude XT touch screen issue

  - by Jake

  yesterday I installed windows 7 ultimate after I had the enterprise version on this machine for a few months. the installation went smoothly and everything worked fine except for the finger detection of the screen(only the pen worked) and the bottom screen buttons for rotating and so. so I started to install all the missing drivers dell recommends for this model on their site, but once I tried to install N-Trig degitizer driver the installation said it was unsuccessful and since then the touch stopped working completely! I tried system restore but it didn't help so I went on and formatted the harddisk completely once again and installed windows but that didn't work either. I tried to install the N-Trig's driver but it was alarting for a fatal error and said that no device was detected. same story with N-Trig rollback. so I checked the device manager and saw an "unknown device" with VID and PID values set as 0000. I figured the N-Trig driver might have messed with the device firmware or something and now it doesnt know it's ID and munufactor... Is there anything that can be done? like forcing the N-Trig driver to install on this device or something? please help!

  Read the article

• RAID-capable 3.5" SATA Drives

  - by nroam

  I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >