Search Results

Search found 6605 results on 265 pages for 'complex networks'.

Page 68/265 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7?

  - by Timo

  The question says it all, but more detail follows ;) I've got a new computer that runs Windows 7 64-bits (Home Edition) and I'd like to connect it to my wireless home network (Sitecom wireless gigabit router 300N wl-352 v1 002) with a Sitecom wireless USB micro adaptapter 300 wl-352 V2 001. After installing the router (i.e. connected to the modem and power) and ensuring that wireless is indeed enabled, I've installed the driver of the USB adapter on the new computer described above. After the installation (drivers and utility on CD) completes successfull I rebooted my computer and inserted the USB adapter. After discovering the right network and connecting to it using the network key, a connection is succesfully made. (Using the Sitecom 300N USB Wireless LAN utility). In the LAN utility I can see that the signal strength is approximately 50% and connection quality is approximately 80%. Judging from these numbers I assumed that all was fine and started to use the connection (reading news on nu.nl, a dutch news site), but noticed that the connection was lost several times in a very short time span, but each time the connections was resumed, resulting in the 50/80 percent numbers described above. However, the website was not loaded completely and often a timeout would be reported. When inspecting the drivers through Device Management (Windows' Apparaatbeheer in dutch) there were no errors/warnings; everything seemed to be in order. In an attempt to solve this, I downloaded the latest drivers for the USB adapter, but the problems remained. Finally I tried to connect the computer with a Siemens Gigaset USB Adapter 108. This process was a troublesome since I had to download a driver (from the site above) and tell Windows (7) to use the Windows Vista driver when installing the new hardware, since there is (was) no Windows 7 driver available. This resulted in a usable connection, although not very stable when reconfiguring the router. Which took the form of selecting a different wireless channel on the router, even using the Sitecom utility mentioned above to check if there were other networks communicating on that channel (and thus picking a channel that was not used by other networks). Again no result when changing back to the Sitecom USB adapter. Note that this means (I think) that I could use the internet connection with the Siemens adapter, meaning the problem was not in the router. So: How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7? PS Sorry, but should be able to post one link, while I had links in place for the USB adapter, router and the siemens adapter in place as well, but I'm not (yet) allowed to post these... (The site says I can post one link, but only when no links are present will it allow me to post the question...)

  Read the article

• What are the ideal settings for a Belkin WiFi Router to connect to an iPhone? [closed]

  - by user34833

  The Belkin Router (F5D8235-4 v2000) has numerous options in the setup. These are the current settings: Wireless On SSID Buster's Special Security Type WPA Encryption Type TKIP WLAN MAC Address 00:22:75:B3:58:38 WPS Enabled Guest Access Disabled SSID Belkin_N+_Guest Password/PSK NotThatSillyYet :) The iPhone is a 3g with 16GB it has no problems connecting to public networks like libraries or restaurants. But currently it won't connect to my home WiFi. Thanks for your time and help. Paul

  Read the article

• isa 2004 - banned site rule cause slow internet

  - by Holian

  Hi Gods, We have windows server 2003 with isa 2004. Our clients uses internet with proxy. We have two isa rule: order name action protocolls from/listener to condition 1. trafic ALLOW all outbound all networks all networks all users 2. FTP ALLOW FTP Server EXTERNAL/INTERNAL/Local host 10.1.1.1 So we have to "bann" a few webpage (like facebook, youtube...etc...), so we make a new rule 0. banned DENY HTTP internal denied pages all users In the denied pages we have the *.facebook.com domain set. After we enable this rule, the entire internet slows down. The banning rule works well, redirect to an internal site, but the other sites.... If i open a page..it normally takes 3-10 sec to load, but after this rule this time is: 2-4 minutes. In the monitor / logging menu we got a few FAILED CONNECTION ATTEMPT like: Log type: Web Proxy (Forward) Status: 304 Not Modified Rule: All local traffic Source: Internal ( 10.1.1.1:0 ) Destination: External ( 172.24.28.22:3128 ) Request: GET http://www.konyvelozona.hu/wp-content/uploads/nyugdijas-holgy-2.jpg Filter information: Req ID: 17270b72 Protocol: http User: anonymous Additional information Client agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.3072... Object source: Verified Cache Processing time: 9047 Cache info: 0x18801002 MIME type: - In the event log we got a few log: Description: The Web Proxy filter failed to bind its socket to 10.1.1.1 port 80. This may have been caused by another service that is already using the same port or by a network adapter that is not functional. To resolve this issue, restart the Microsoft Firewall service. The error code specified in the data area of the event properties indicates the cause of the failure. The failure is due to error: 0x8007271d The Web Proxy filter failed to bind its socket to 127.0.0.1 port 80. This may have been caused by another service that is already using the same port or by a network adapter that is not functional. To resolve this issue, restart the Microsoft Firewall service. The error code specified in the data area of the event properties indicates the cause of the failure. The failure is due to error: 0x8007271d If i tpye: netstat -o -n -a | findstr 0.0:80 then i got, tcp 0.0.0.0:80 0.0.0.0:0 LISTEN 4 udp 0.0.0.0:8031 *.* 2780 udp 0.0.0.0:8082 *.* 2780 Some month ago we installed XMAP, but now we only use mysql. Apache service stopped. In the Xamp port check menu i see: Service POrt Status Apache (http) 80 Process: System Maybee this is the problem? I dont know what should i do now... Thank you folks.

  Read the article

• Tomato VPN connect but cannot ping LAN IP

  - by David Hamilton

  I've setup TomatoVPN using these settings on the server: TAP UDP 1194 Client address pool 10.10.9.1 -10.10.9.254 LAN clients are configured with 10.10.10.x I can connect from a remote client, but pinging anything in the 10.10.10.x results in a "Destination Host Unreachable" error. Here's my client configuration script: remote x.x.x.x 1194 client dev tap0 proto udp resolv-retry infinite nobind persist-key persist-tun float ca ca.crt cert client1.crt key client1.key ns-cert-type server Any suggestions as how I can make this properly bridge the two networks?

  Read the article

• Use-cases for assigning multiple IP addresses to 1 NIC

  - by Harry

  What would be some of major use-cases in which you would want to assign multiple IP addresses to your NIC? Knowing of any standard/well-known 'gotchas' associated with each use-case would also be helpful. For example, I heard someone saying that a user with access to such a machine will automatically get access to both networks, which could be a security issue. You can assume a Linux-based environment.

  Read the article

• WiFi signal is lost every 3 minutes

  - by Software Monkey

  For several weeks now my Android phone has been losing it's WiFi signal momentarily, typically at about 3 minute intervals (about 3 minutes, 1.5 seconds) and occasionally at some longer interval that always seems to be just over 3 minutes. This causes an interruption of several seconds while the WiFi connection is re-established and typically fails any kind of download/streaming that is happening, makes web sites "unreachable" and generally makes the phone unusable as a data device due to the frequency. The signal remains down for about a second, but the phone takes a few more seconds to reconnect to the router. This happens regardless of proximity to the router, which otherwise show a very strong signal - usually -40 to -30 dBm or better in the same room, nowhere less than 060 dBm anywhere in the house. Changing channels does not help (I've tried 1, 4, 8 and 9). Nor does turning off the router's guest access. Nor does turning off the 5.0 GHz band. Monitoring the signal on my phone with WiFi analyzer, shows all WiFi signals on all channels drop to nothing when the WiFi connection is lost (there are two other networks on different channels which are strong enough to be relevant, with about 6 others constantly fading in and out). WiFi analyzer shows 3 separate signals for my router, the main 2.4 GHz, the guest 2.4 GHz and the 5.0 GHz. Using WiFi Analyzer on my wife's phone side-by-side shows no change in signal when my phone drops, nor does her phone drop. Monitoring the signal using our laptop, side-by-side likewise shows no signal loss and likewise the laptop does not lose it's WiFi connection. But, at work, the phone seems to not exhibit the same behavior, or, if it does, it's very occasional. Monitoring it all day at work I only saw the signal drop 3 or 4 times. The signal strength of the various networks there is comparatively weak. AT&T were super helpful: "Sorry, we can't help you with WiFi problems. You could try doing a factory reset on your phone". </sarcasm The router is relatively new, but has been working fine with this phone since last Dec. Phone : Motorola Atrix (about 8 months old). Router : Belkin N750 DB (F9K1103 v1 (01C)). Router Firmware: 1.00.46 (2011/10/28 6:37:11). Security : WPA/WPA2-Personal (PSK)

  Read the article

• Replace DNS on Openvpn client without redirect-gateway

  - by Gabor Vincze

  I am trying to push DNS to the client with OpenVPN server with config: push "dhcp-option DNS 192.168.x.x" It is working well, but what I really need is that during the VPN connection I do not want to use my primary resolvers, clients should use only the DNS provided by the server. It can be done with push redirect-gateway, but I do not want to tunnel all connections from the client thru the VPN, only specific networks. Is it possible to do it somehow? Linux clients are OK with a script, on Windows I am not sure

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• No WPA2 option in Windows XP SP3

  - by user34300

  I have a fresh Windows XP SP3 installation on several PCs but none of them has WPA/WPA2 option in Wireless Networks section of the connection properties regardless of wireless adapters they have (that supports WPA2). Can someone provide an advice on how to fix that?

  Read the article

• VPN software to use internet connection of remote network

  - by eych

  Which software will allow a VPN connection to a remote network and utilize that networks internet connection? Useful for unknown free wi-fi areas to connect to a solid connection elsewhere. Kind of like a remote desktop connection software (e.g. Teamviewer), but you just need internet access.

  Read the article

• My Ubuntu Laptop Can't Connect to a Particular Wireless Network, while Windows Laptops do

  - by phaedrus

  The wireless on my Ubuntu works on all the other wireless networks. But on this university network it never forms a connection. But I can see the signal at 80% (indeed I see several signals at 80%, 40% and 20% by the same name university-network name). On a Windows XP laptop, the connection is formed as usual, and there is only one network visible to Windows.

  Read the article

• Detecting what causes the delay between entering a domain name and load of the page

  - by Quintin Par

  My website takes awfully long time after entering the domain name and before the content starts showing up. I assume this is something to do with the dns resolution or the networks. How do I go about troubleshooting this problem? Where do I start and what tools do I need? I know I’ll need nslookup and traceroute. What else will I need?

  Read the article

• How to connect laptop with telephone using WI-FI? (ethernet)

  - by rmaster

  What I did: 1)added new wireless network in wireless network settings and gave it SSID 2)gave laptop the IP like 192.168.0.1, mask: 255.255.255.0, gateway: 192.168.0.2 3)gave the telephone with wifi the same mask but IP and gateway rewersed But telephone can not find my new wireless network(it can find all other networks), computer also can not find it. where is error? how to make it visible and working? if my steps are wrong tell me correct way to establish this connection via wi-fi

  Read the article

• Creating an Ad-Hoc network between two laptops on Windows 7 ?

  - by Morano88

  I want to create an Ad-Hoc network between two laptops on Windows 7. I do that but it keeps disconnecting. What is the reason ? Can you give me a guide me to a good tutorial for creating ad-hoc networks ?

  Read the article

• Set web browser (or other program) to use specific network

  - by Will

  my PC is connected to 3 different networks: 2 different LAN connections and a VPN connection. when i am connected to the vpn, i cannot browse to the LAN intranet as the DNS is all going through the vpn and it cannot see the domains on the LAN. Is there a way to set firefox/chrome/etc to use a specific connection, so that i don't have to disconnect from vpn to get to the other intranets?

  Read the article

• remote desktop computer viewer?

  - by Josh

  I would like to install a quad core computer in my dorm at college and use my much slower laptop to be able to control the quad core just as if I had a quad core laptop (control as in i see the gui, not command line control)! Both are on the same college network, though Im also interested in what would be necessary if the computers were on different networks. What would be the best method fot this? Im looking for non-lag communication.

  Read the article

• Disable File Copy between VMs

  - by shawnnny

  When I access multiple virtual desktops via VMware View 4, I'm able to copy files between VMs. The VMs are located in different isolated networks. This is a security concern in my organization and how can I disable this feature? I'm not able to find any related configuration in View Connection Server. Thanks!

  Read the article

• WIFI connection not working

  - by chris verwey

  We have a wireless network that is set to secure, it does show as unsecure on my laptop, and desktop connect to router but no internet access. other computers on the network require password to connect to router and get internet access. Iphone and Ipads connect using password and also have internet access, what can I do to fix it. Laptop = dell e6410 Router = netgear The laptop work on other wireless networks without any problem

  Read the article

• External WiFi Adapter for Eee PC 1000?

  - by Peter M

  I have an original Eee PC 1000 running the stock Xandros. I have run into problems where the internal WiFi card does not seem to have enough sensitivity to connect to a lot of access points. Although the computer will report APs in the area, unless the signal strength is over 80% (as reported by the Wireless networks application) I cannot seem get a connection. So is there a recommended USB WiFi adapter that is known to work with the Eee PC/Xandros system or in general with a Debian based system?

  Read the article

• Hotel like Wifi manager

  - by flpgdt

  Does anyone knows which are these systems that manages paid wifi networks and some hotels and airports? Even better, would anyone know a open/free project that would do or could be adapted to that end? The idea is simple, I want to let the network open at physical level so anyone can connect. After connected however, the clients would have access only to a specified page where they can logging in, and doing the necessary validations the router would allow these of those ports (or even everything) for his IP.

  Read the article

• Is there any reason to have 2 NICs on a server?

  - by RichAmberale

  Is there any reason to have 2 NICs on a server BESIDES the following cases? You need to connect to 2 different physical networks Redudancy (1 NIC fails, so you use the other) Are there any other reasons?

  Read the article

• VPN connects but no remote lan access

  - by Macros

  I have a PPTP_ VPN setup through Windows to a Cisco (LinkSYS) router, which was working fine up until yesterday. Now I can connect, and I can ping the router however I am unable to reach any of the machines on the remote network. I've tried this from multiple PCs on Multiple networks / internet connections wuth the same results. Any ideas what may have caused this?

  Read the article

• Fedora internet access and managing

  - by Fractal

  This questions speaks about a UNIX Fedora install, DWA-552 wireless adapter, and internet What are the required packages on a KDE GUI installation, and on the basic UNIX TUI installation, to access internet and manage wireless networks? On a larger scale, does anyone knows of an all encompassing list of basic functions (such as monitoring or hardware control) with their respective packages dependencies?

  Read the article

• Is it possible to do "something" every time linux connects to a network?

  - by quodlibetor

  Hey, I'm trying to make a script run every time NetworkManager (or whatever, but that's what I'm talking to right now) connects to a network (or changes networks). What I really want is, metaphorically, an init directory that fires everything inside of it whenever my wifi interface changes state/essid. Or a "network status changed" runlevel. Or something.

  Read the article

• Disabling parallel network connections on workstation

  - by sumar

  Is it possible to disable prarallel network connections on workstation, when workstation is connected to corporate LAN? I want to avoid users bypassing Internet access policies by concurently connect to LAN and 3G/Hotspot. We have many developers and they have local administrator rights on workstations. Developers should be able to connect virutual networks (VMware/VirutalPC/Hyper-V/VirutalBox). Other users should be able to use only one network connection concurently.

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >