Search Results

Search found 7592 results on 304 pages for 'dev g'.

Page 68/304 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• Harddisk formatting with dd return error

  - by Usman Ajmal

  Hi, I tried to format my harddisk (160 GB) with the following command dd if=/dev/zero of=/dev/sda After some 3 hours, following error came up: dd: writing to '/dev/sda' : No space left on device 312581809+0 records in 312581808+0 records out 160041885696 bytes (160 GB) copied, 10708.3 s, 14.9 MB/s Any idea what went wrong?

  Read the article

• Instructions to setup domain controller

  - by Robert Koritnik

  Where could I get best step by step instructions (with some simple explanations) how to setup domain controller on Windows Server 2008 R2 Server Core? I don't know what do I need? Do I need DNS as well and AD and so on and so forth. I don't know enough about these things, but I need to set them up to prepare development environment. I would also like to know how to configure firewall on DC machine, to make it visible on other machines because I've setup DC somehow but I can't connect to it... This is my HW config: Linksys internet router with DHCP my dev machine is Windows 7 my DC machine is a VM in my dev machine my dev machine has a network adapter to linksys and a virtual adapter to DC DC machine has two network adapters: one to linksys (to be inetrnet connected) and one to host (my dev Win7 machine)

  Read the article

• Linux Software RAID1 Rebuild Completes, but after reboot, its degraded again

  - by zimmy6996

  I have been beating my head with an issue here, and I'm now turning to the internet for help. I have a system running Mandrake Linux, with the following configuration: /dev/hda - This is a IDE drive. Has some partitions on it that boot the system and make up most of the file system. /dev/sda - This is drive 1 of 2 for a software raid /dev/md0 /dev/sdb - This is drive 2 of 2 for a software raid /dev/md0 md0 gets mounted but fstab as /data-storage, so it is not critical to the systems ability to boot. We can comment it out of fstab, and the system works just fine either way. The problem is, we have a failed sdb drive. So I shut the box down, and have pulled the failed disk and installed a new disk. When the system boots up, /proc/mdstat shows only sda as part of the raid. I then run the various command to rebuild the RAID to /dev/sdb. Everything rebuilds correctly, and upon completion, you look at /proc/mdstat and it shows 2 drives sda1(0) and sdb1(1). Everything looks great. Then you reboot the box ... UGH!!! Once rebooted, sdb is missing again from the RAID. It is like the rebuild never happened. I can walk through the commands to rebuild it again, and it will work, but again, after reboot, the box seems to make sdb just vanish! The real odd thing is, if after reboot, I pull sda out of the box, and try to get the system to load with the rebuilt sdb drive in the system, and when I do, the system actually throws and error just after grub, and says something about drive error, and the system has to shut down. Thoughts??? I'm starting to wonder if grub has something to do with this mess. That the drive isn't being setup within grub to be visible at boot? This RAID array isn't necessary for the system to boot, but when the replacement drive is in there, without SDA it won't boot system, so it makes me believe there is something to that. On top of that, there just seems to be something wonky here the drive falling off of RAID after reboot. I've hit the point of pounding my head on the keyboard. Any help would be greatly appreciated!!!

  Read the article

• Automatically distinguish difference between multiple HDDs in linux?

  - by Jakobud

  I'm running Ubuntu Server 9.10. I have two external USB HDDs. I use them each for different backup reasons. So certain data gets stored on one HDD, and different information gets stored on the other HDD. I want to make a script that can look at the external HDD can determine which HDD it is, so that it can copy the proper information to it. Is there a way for Linux to determine this? Like if I see one HDD as /dev/sdc1, then unplug it and plug in the other HDD, should Linux see it as /dev/sdd1 or will it be /dev/sdc1? I'm a bit of a Linux newb and I don't quite understand how it determines the /dev/sdxx values that it assigns to drives.

  Read the article

• Server 2008 unresponsive after SP2 install.

  - by Dan

  I have a dev server that has an exact image of a production web server. The prod server only has SP1 installed on it. When I first fired up the dev box, the first thing I did was install SP2, and let it be. Almost every morning when I came in, the server was unusable. It would respond to ping, but RDP and the web site running on it were down. On the screen the screen saver was bouncing around, so it wasn't hard locked. But it was unresponsive to keyboard and mouse. So now I have to hard shut it down, but when it comes back up, the only thing in the event viewer is the unexpected shutdown, nothing else. I've since taken a fresh image of my prod box and put it on the dev server, and not installed SP2, and the dev box is humming along perfectly. I should also note that this is Server2k8 Web, 64bit Has anyone else seen anything like this?

  Read the article

• Any way to recover ext4 filesystems from a deleted LVM logical volume?

  - by Vegar Nilsen

  The other day I had a proper brain fart moment while expanding a disk on a Linux guest under Vmware. I stretched the Vmware disk file to the desired size and then I did what I usually do on Linux guests without LVM: I deleted the LVM partition and recreated it, starting in the same spot as the old one, but extended to the new size of the disk. (Which will be followed by fsck and resize2fs.) And then I realized that LVM doesn't behave the same way as ext2/3/4 on raw partitions... After restoring the Linux guest from the most recent backup (taken only five hours earlier, luckily) I'm now curious on how I could have recovered from the following scenario. It's after all virtually guaranteed that I'll be a dumb ass in the future as well. Virtual Linux guest with one disk, partitioned into one /boot (primary) partition (/dev/sda1) of 256MB, and the rest in a logical, extended partition (/dev/sda5). /dev/sda5 is then setup as a physical volume with pvcreate, and one volume group (vgroup00) created on top of it with the usual vgcreate command. vgroup00 is then split into two logical volumes root and swap, which are used for / and swap, logically. / is an ext4 file system. Since I had backups of the broken guest I was able to recreate the volume group with vgcfgrestore from the backup LVM setup found under /etc/lvm/backup, with the same UUID for the physical volume and all that. After running this I had two logical volumes with the same size as earlier, with 4GB free space where I had stretched the disk. However, when I tried to run "fsck /dev/mapper/vgroup00-root" it complained about a broken superblock. I tried to locate backup superblocks by running "mke2fs -n /dev/mapper/vgroup00-root" but none of those worked either. Then I tried to run TestDisk but when I asked it to find superblocks it only gave an error about not being able to open the file system due to a broken file system. So, with the default allocation policy for LVM2 in Ubuntu Server 10.04 64-bit, is it possible that the logical volumes are allocated from the end of the volume group? That would definitely explain why the restored logical volumes didn't contain the expected data. Could I have recovered by recreating /dev/sda5 with exactly the same size and disk position as earlier? Are there any other tools I could have used to find and recover the file system? (And clearly, the question is not whether or not I should have done this in a different way from the start, I know that. This is a question about what to do when shit has already hit the fan.)

  Read the article

• Connecting to a computer using Remote Desktop does not work first time

  - by dev

  Hi all, I'm having a weird sort of problem with Remote desktop and that too, only on one machine. If I boot up this machine, and then try to Remote desktop into it, it does not work.( I get the following error: The client could not connect to the remote computer. Remote connections might not be enabled or the computer might be too busy to accept new connections. It is also possible that network problems are preventing your connection. Please try connecting again later. If the problem continues to occur, contact your administrator. ) But if I physically log into it & then log out, and then try to Remote desktop into it, it works flawlessly. The problematic machine is Xp 64 Bit, but other systems with Xp 64 Bit work fine. Any Ideas on how to solve this?

  Read the article

• Can't mount home after trying to resize (bad geometry: block count exceeds size of device).

  - by Lynn

  This is on a fresh computer (super computer actually). It got to me with 15T on the home mount and 50G on the root. I tried allocating 7T to root and resizing (since I'm putting a local yum repo on this machine as it has no internet access nor will it ever). I tried following the instructions here: Centos 6.3 disk space allocation but something went wrong and the home won't mount again. Instead I get from dmesg | tail: EXT4-fs (dm-2): bad geometry: block count 4294967295 exceeds size of device (1342177280 blocks) df -h nets this output: Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-lv_root 7.0T 3.6G 6.6T 1% / tmpfs 190G 216K 190G 1% /dev/shm /dev/sda1 485M 38M 422M 9% /boot I didn't have any files on /dev/mapper/VolGroup-lv_home. Will simply running mke2fs fix it to be mountable? What sort of options should I run it with. I've never resized volumes before or used mke2fs. I don't want to make this mess worse.

  Read the article

• Adobe Illustrator - Objects are Expanded on Restart

  - by Shatou Dev

  I use Adobe Illustrator extensively for mobile development. For example, for Android app, I have many illustrations with different densities and sizes. I use many effects such as outer glow, round corners and such. However, sometimes, when I close the .ai file and re-open it later, I found all my objects expanded. Effects are expanded. For example, the round corner effect is now expanded and I cannot re-size any object. I am using a MacBook Pro. I am suspecting both Time Machine and Dropbox. As much as I can recall, it also appears with CS6 version, not CS5.

  Read the article

• netkit: why cant my router 4 pc4 ping my router 1 pc1 - how can I solve this please?

  - by donok

  Below I have four routers connected but my pc1 on r1 cannot ping my pc4 on r4 and also my pc2 on r2 cant ping my pc4 on r4 and vice versa. Below is a network diagram: and the configurations are below that, could anyone help me please on making them accessible? ![connecting 4 routers][1] I cant post my diagram on serverfault(less than 10 rep) so I did on stackoverflow and asked the same question. pc1: ifconfig eth0 195.11.14.5 netmask 255.255.255.0 broadcast 195.11.14.255 up route add default gw 195.11.14.1 dev eth0 pc2.start: ifconfig eth0 200.1.1.7 netmask 255.255.255.0 broadcast 200.1.1.255 up route add default gw 200.1.1.1 dev eth0 pc3: ifconfig eth0 195.20.14.9 netmask 255.255.255.0 broadcast 195.20.1.255 up route add default gw 195.20.14.1 dev eth0 pc4: ifconfig eth0 200.2.1.11 netmask 255.255.255.0 broadcast 200.2.1.255 up route add default gw 200.2.1.1 dev eth0 r1: ifconfig eth0 195.11.14.1 netmask 255.255.255.0 broadcast 195.11.14.255 up ifconfig eth1 100.0.0.9 netmask 255.255.255.252 broadcast 100.0.0.11 up route add -net 200.1.1.0 netmask 255.255.255.0 gw 100.0.0.10 dev eth1 route add default gw 100.0.0.10 lab.conf: if you need more on that Ill post it up but I think most of the info is there. Any help would be greatly appreciated especially trying to make a connection between pc4 and pc1, even if you think it does not make sense please explain why. Thank you.

  Read the article

• fstab mount after network initialization

  - by Philip

  I'm automatically mounting a NFS with fstab. Sometimes the mount fails because the hostname of the NFS mount cannot be resolved (getaddrinfo failed). I'm assuming that this happens because the network initialization is slower than the mounts. Is there any way to initialize the network before mounting any devices? I'm already using _netdev as a mount option but this does not help. This is my current fstab file: # <file system> <mount point> <type> <options> <dump> <pass> /dev/md2 / ext3 errors=remount-ro 0 1 /dev/md1 /boot ext3 errors=remount-ro 0 1 /dev/sda3 swap swap defaults 0 0 /dev/sdb3 swap swap defaults 0 0 connect.mygluster.net:/data /var/gluster/data glusterfs ro,_netdev 0

  Read the article

• NTFS write speed really slow (<15MB/s)

  - by Zulakis

  I got a new Seagate 4TB harddrive formatted with ntfs using parted /dev/sda > mklabel gpt > mkpart pri 1 -1 mkfs.ntfs /dev/sda1 When copying files or testing writespeed with dd, the max writespeed I can get is about 12MB/s. The harddrive should be capable of atleast 100MB/s. top shows high cpu usage for the mount.ntfs process. The system has a AMD dualcore. This is the output of parted /dev/sda unit s print: Model: ATA ST4000DM000-1F21 (scsi) Disk /dev/sda: 7814037168s Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 2048s 7814035455s 7814033408s pri The used kernel is 3.5.0-23-generic. The ntfs-3g versions I tried are ntfs-3g 2012.1.15AR.1 (ubuntu 12.04 default) and the newest version ntfs-3g 2013.1.13AR.2. When formatted with ext4 I get good write speeds with about 140MB/s. How can I fix the writespeed?

  Read the article

• how to resolve all externally unresolved DNS queries ?

  - by red eyes dev

  I am using PowerDns on a Linux box (Debian 6). I would like to set up the powerdns server to resolve all externally unresolved DNS queries to a given, internal host. Is this possible? How is it done? I think it's necessary to use pdns-recursor, but my configuration file doesn't works ! I use mysql for backend. I add manually google.com and it's works, but if I delete entry I have "server failed", root dns (or isp dns) don't answer me.

  Read the article

• Missing hvc0 in Ubuntu Lucid Xen DomU

  - by Joril

  I've just installed an Ubuntu Lucid 64bit image (from Stacklet) as a Xen DomU, running under Xen 3.2.1 on Centos 5.2 64bit. Everything is working fine, except my logs are flooded with: /dev/hvc0: No such file or directory I tried creating the device with mknod /dev/hvc0 c 229 0 but the message just changes to: /dev/hvc0: cannot open as standard input: No such device or address Any hint on what I could try? :(

  Read the article

• SAS disk performance drops a while after reboot.

  - by Flamewires

  So we have some workstations with identical hardware. The Fedora14 box has a couple weeks uptime and still get good performance. hdparm -tT /dev/sda /dev/sda: Timing cached reads: 21766 MB in 2.00 seconds = 10902.12 MB/sec Timing buffered disk reads: 586 MB in 3.00 seconds = 195.20 MB/sec The Cent 5.5 boxes however seem to be okay after a reboot, /dev/sda: Timing cached reads: 34636 MB in 2.00 seconds = 17354.64 MB/sec Timing buffered disk reads: 498 MB in 3.01 seconds = 165.62 MB/sec but some time later( unsure exactly, tested at approx 1 day uptime) /dev/sda: Timing cached reads: 2132 MB in 2.00 seconds = 1064.96 MB/sec Timing buffered disk reads: 160 MB in 3.01 seconds = 53.16 MB/sec drop to this. This is with very low load. I believe they all have the same bios settings. Any ideas what could cause this on Cent? Ask for more info. It might also be worth noting, that passing the --direct flag causes the slow boxes to perform similarly to the non-slow ones for buffered disk reads.

  Read the article

• Mac OS X missing disk

  - by leo

  In boot camp, it only see partition size to be 149G while disk utility shows only one partition with size 320G. Why diskutil and df gives me different sizes? Also how can i fix it? thanks df -h Filesystem Size Used Avail Capacity Mounted on /dev/disk0s2 **149Gi 20Gi 129Gi 14% /** devfs 110Ki 110Ki 0Bi 100% /dev map -hosts 0Bi 0Bi 0Bi 100% /net map auto_home 0Bi 0Bi 0Bi 100% /home and diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme ***320.1 GB disk0** 1: EFI 209.7 MB disk0s1 2: Apple_HFS Mac HD 319.6 GB disk0s2

  Read the article

• CentOS 6.5 new Kernel not active after reboot

  - by Kristofer

  Today I was running some yum updates and wanted to verify that everything went through fine by making sure I had a new kernel. To my surprise I noticed that CentOS was still running 2.6.32-431.5.1.el6.x86_64 even though it looked as though 2.6.32-431.23.3.el6 was installed. Indeed 2.6.32-431.23.3.el6 shows up in /etc/grub.conf but not in the upstart boot options. Any ideas why? In the update log it says: ---> Package kernel-firmware.noarch 0:2.6.32-431.5.1.el6 will be updated ---> Package kernel-firmware.noarch 0:2.6.32-431.23.3.el6 will be an update Could this be the reason? What does "will be an update" mean? My /etc/grub.conf: # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/VolGroup00-root # initrd /initrd-[generic-]version.img #boot=/dev/vda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu password --encrypted $1$auui(i$sODM4ni/Zts9IlMWu.wWF/ title CentOS (2.6.32-431.23.3.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.23.3.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.23.3.el6.x86_64.img title CentOS (2.6.32-431.5.1.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.5.1.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.5.1.el6.x86_64.img title CentOS (2.6.32-431.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.el6.x86_64.img

  Read the article

• Openvpn - stuck on Connecting

  - by user224277

  I've got a problem with openvpn server... every time when I trying to connect to the VPN , I am getting a window with login and password box, so I typed my login and password (login = Common Name (user1) and password is from a challenge password from the client certificate. Logs : Jun 7 17:03:05 test ovpn-openvpn[5618]: Authenticate/Decrypt packet error: packet HMAC authentication failed Jun 7 17:03:05 test ovpn-openvpn[5618]: TLS Error: incoming packet authentication failed from [AF_INET]80.**.**.***:54179 Client.ovpn : client #dev tap dev tun #proto tcp proto udp remote [Server IP] 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert user1.crt key user1.key <tls-auth> -----BEGIN OpenVPN Static key V1----- d1e0... -----END OpenVPN Static key V1----- </tls-auth> ns-cert-type server cipher AES-256-CBC comp-lzo yes verb 0 mute 20 My openvpn.conf : port 1194 #proto tcp proto udp #dev tap dev tun #dev-node MyTap ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/VPN.crt key /etc/openvpn/keys/VPN.key dh /etc/openvpn/keys/dh2048.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt #push „route 192.168.5.0 255.255.255.0? #push „route 192.168.10.0 255.255.255.0? keepalive 10 120 tls-auth /etc/openvpn/keys/ta.key 0 #cipher BF-CBC # Blowfish #cipher AES-128-CBC # AES #cipher DES-EDE3-CBC # Triple-DES comp-lzo #max-clients 100 #user nobody #group nogroup persist-key persist-tun status openvpn-status.log #log openvpn.log #log-append openvpn.log verb 3 sysctl : net.ipv4.ip_forward=1

  Read the article

• OpenVPN + iptables / NAT routing

  - by Mikeage

  Hi, I'm trying to set up an OpenVPN VPN, which will carry some (but not all) traffic from the clients to the internet via the OpenVPN server. My OpenVPN server has a public IP on eth0, and is using tap0 to create a local network, 192.168.2.x. I have a client which connects from local IP 192.168.1.101 and gets VPN IP 192.168.2.3. On the server, I ran: iptables -A INPUT -i tap+ -j ACCEPT iptables -A FORWARD -i tap+ -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE On the client, the default remains to route via 192.168.1.1. In order to point it to 192.168.2.1 for HTTP, I ran ip rule add fwmark 0x50 table 200 ip route add table 200 default via 192.168.2.1 iptables -t mangle -A OUTPUT -j MARK -p tcp --dport 80 --set-mark 80 Now, if I try accessing a website on the client (say, wget google.com), it just hangs there. On the server, I can see $ sudo tcpdump -n -i tap0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tap0, link-type EN10MB (Ethernet), capture size 96 bytes 05:39:07.928358 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 558838 0,nop,wscale 5> 05:39:10.751921 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 559588 0,nop,wscale 5> Where 74.125.67.100 is the IP it gets for google.com . Why isn't the MASQUERADE working? More precisely, I see that the source showing up as 192.168.1.101 -- shouldn't there be something to indicate that it came from the VPN? Edit: Some routes [from the client] $ ip route show table main 192.168.2.0/24 dev tap0 proto kernel scope link src 192.168.2.4 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.101 metric 2 169.254.0.0/16 dev wlan0 scope link metric 1000 default via 192.168.1.1 dev wlan0 proto static $ ip route show table 200 default via 192.168.2.1 dev tap0

  Read the article

• Devices renamed with udev not working, original device node still there

  - by skerit

  I'm trying to rename certain video devices using udev. Here's a rule (broken down for readability): ACTION=="add", SUBSYSTEM=="usb", ATTR{busnum}=="1", ATTR{devpath}=="2", ATTR{idVendor}=="05e1", NAME="video97" It works. /dev/video97 is created But the original /dev/video1 node is STILL there. The even worse, when I try to view the /dev/video97 node in guvcview it doesn't work, while the original node DOES work.

  Read the article

• Software RAID 1 Configuration

  - by Corve

  I have created a software RAID 1 quite some while ago and it always seemed to work for me. However I am not completely sure that I have configured everything right and do not have the experience to check so I would be very grateful for some advice or just verification that all seems right so far. I am using Linux Fedora 20 (32 bit with plans to upgrade to 64bit) The RAID 1 should consist of two 1TB SATA hard drives. This is the output of mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sun Jan 29 11:25:18 2012 Raid Level : raid1 Array Size : 976761424 (931.51 GiB 1000.20 GB) Used Dev Size : 976761424 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Sat Jun 7 10:38:09 2014 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : argo:0 (local to host argo) UUID : 1596d0a1:5806e590:c56d0b27:765e3220 Events : 996387 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 0 1 active sync /dev/sda The RAID is mounted successfully: friedrich@argo:~ ? sudo mount -l | grep md0 /dev/md0 on /mnt/raid type ext4 (rw,relatime,data=ordered) Basically my question are: Why do I only have 1 active device? What does the State removed at bottom mean? Also I noticed some strange error messages that I see on the console on system start and shutdown and always repeating in the background when I switch with Ctrl + Alt + F2: ... ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: COMRESET failed (errno=-32) ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ... Are these errors related to the RAID? Something seems wrong with the SATA devices.. All together the system works (I can read and write to the mounted raid) but I always had these strange errors on startup shutdown (probably always in the background). Thx for your help

  Read the article

• MTD mtd3ro backup returns BCH decoding failed

  - by saeed144

  While doing a kernel backup of an mtd (Memory Technology Device) from /dev/mtd/mtd3ro of a TI board gives many "BCH decoding failed", Here are system info #cat /proc/mtd dev: size erasesize name mtd0: 00080000 00020000 "X-Loader" mtd1: 00140000 00020000 "U-Boot" mtd2: 000c0000 00020000 "U-Boot Env" mtd3: 00500000 00020000 "Kernel" mtd4: 1f880000 00020000 "File System" here is the method used, dd if=/dev/mtd/mtd3ro of=/data/local/tmp/mtd3.bin doing a cat also returns the same error, and here is the error, BCH decoding failed BCH decoding failed yes, the destination has enough space ;) tell me what do you think? Thanks

  Read the article

• Disk doesn't contain a valid partition table

  - by Jeevan Dongre

  I was running a m1.small instance ec2 ubuntu instance. I was running out of disk space, so I upgraded my instance to medium. When I upgraded I actually got 429.5 GB of space and after that I added 10 gb of volume too. When I run the "sudo fdisk -l" command I got this results. Disk /dev/sda1: 8589 MB, 8589934592 bytes 255 heads, 63 sectors/track, 1044 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 429.5 GB, 429461078016 bytes 255 heads, 63 sectors/track, 52212 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda2 doesn't contain a valid partition table Disk /dev/sdf: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 sda1 is the primary parition and sda2 is what I got added upgrading my system to medium. But the problem persists, I am not able to pull the code from git, it is giving me this error. remote: Counting objects: 409, done. remote: Compressing objects: 100% (236/236), done. fatal: write error: No space left on device fatal: index-pack failed

  Read the article

• How can I increase space on the Filesystem linux?

  - by xtrimsky

  I am renting a dedicated server with Parallel Plesk on it (which I hate and I try to use command line). I have a filesystem that is full,"df -H" prints this: Filesystem Size Used Avail Use% Mounted on /dev/md1 4.0G 4.0G 361k 100% / /dev/mapper/vg00-usr 4.3G 1.4G 3.0G 32% /usr /dev/mapper/vg00-var 4.3G 2.8G 1.6G 64% /var /dev/mapper/vg00-home 4.3G 4.4M 4.3G 1% /home none 1.1G 24M 1.1G 3% /tmp tmpfs 1.1G 0 1.1G 0% /usr/local/psa/handlers/before-local tmpfs 1.1G 0 1.1G 0% /usr/local/psa/handlers/before-queue tmpfs 1.1G 0 1.1G 0% /usr/local/psa/handlers/before-remote tmpfs 1.1G 0 1.1G 0% /usr/local/psa/handlers/info tmpfs 1.1G 0 1.1G 0% /usr/local/psa/handlers/spool The server I'm renting has 1TB of hard drive. Why are these so small, how can I increase my storage ? (I'm pretty beginner with Linux). Thank you

  Read the article

• OpenVZ kernel panic

  - by GtoXic

  I recently installed OpenVZ on my VMWare box (To do some testing) and I get the following: https://www.dropbox.com/s/p38btkv5j84bvsh/Capture.JPG the GRUB config is as follows: # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/VolGroup00/LogVol00 # initrd /initrd-version.img #boot=/dev/sda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title OpenVZ (2.6.32-042stab057.1) root (hd0,0) kernel /vmlinuz-2.6.32-042stab057.1 ro root=/dev/VolGroup00/LogVol00 sysfs.deprecated=1 initrd /initrd-2.6.32-042stab057.1.img title CentOS (2.6.18-238.el5) root (hd0,0) kernel /vmlinuz-2.6.18-238.el5 ro root=/dev/VolGroup00/LogVol00 initrd /initrd-2.6.18-238.el5.img

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >