Search Results

Search found 7455 results on 299 pages for 'power cable'.

Page 68/299 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

  • Atheros AR928X wireless connection makes neighbourhood machine drop off line

    - by funicorn
    I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

    Read the article

  • How could I shutdown, over my network, with one click?

    - by DeLiK
    The question is simple. What would be the script I would have to use to shut down a computer in my network thru ssh. Normaly i would go to command line and: ssh desktop delik@desktop's password: delik@desktop:~$ sudo shutdown -P 0 To power on I created a file and wrote: wakeonlan xx:xx:xx:xx:xx:xx And gave it the executable bit That way to power on it requires only a double click. Would i be capable of doing the same to shutdown?

    Read the article

  • How to do end task similar to that in Windows?

    - by Rohit Bansal
    Sometimes Ubuntu freezes and I have no other option than to power off system directly. Is there some remedy or way like 'Ctrl + Alt + Del' similar to that in Windows. That would be very helpful..... I need a way out other than option to directly power off my system in times of gross failure. Shutting down this way always creates fear crashing down my system or losing some data which is unacceptable.

    Read the article

  • Manic Monday - More OpenWorld Solaris Sessions: Developers, Cloud, Customer Insights, Hardware Optimization

    - by Larry Wake
    We're overflowing with Monday sessions; literally more than one person can take in. Learn more about what's new in Oracle Solaris Studio, hear about the latest x86 and SPARC hardware optimizations, get some insights on cloud deployment strategies, and find out from your peers what they're doing with Oracle Solaris. If you're an OpenWorld attendee, go to to Schedule Builder to guarantee your space in any session or lab. See yesterday's blog post and the "Focus on Oracle Solaris" guide for even more sessions. Monday, October 1st: 10:45 AM - Maximizing Your SPARC T4 Oracle Solaris Application Performance(CON6382,  Marriott Marquis - Golden Gate C3) Hear how customers and commercial software partners have reached peak performance on SPARC T4 servers and engineered systems with Oracle Solaris Studio and its latest tools for analyzing, reporting, and improving runtime performance: Autoparallelizing, high-performance compilers Performance Analyzer (used to find performance hotspots) Thread Analyzer (to expose data races and deadlocks) Code Analyzer (used to discover latent memory corruption issues) 10:45 Cloud Formation: Implementing IaaS in Practice with Oracle Solaris(CON8787, Moscone South 302) Decisions, decisions--at the same time, we've got a session that covers why Oracle Solaris is the ideal OS for public or private clouds, IaaS or PaaS, with built-in features for elastic infrastructure, unrivaled security, superfast installation and deployment, nonstop availability, and crystal-clear observability. This session will include a customer study on how Oracle Solaris is used in the cloud today to implement the Oracle stack. 12:15 PM - Customer Insight: Oracle Solaris on Oracle Exadata, Oracle Exalogic, and SPARC SuperCluster(CON8760, Moscone South 270) Hear from customers what benefits they have realized from using the Oracle stack on Oracle Exadata and Oracle’s SPARC SuperCluster and from using Oracle Solaris on those engineered systems, taking advantage of built-in lightweight OS virtualization (Zones), enterprise reliability and scale, and other key features. 1:45 PM - Case Study: Mobile Tornado Uses Oracle Technology for Better RAS and TCO?(CON4281, Moscone West 2005) Mobile Tornado develops and markets instant communication platforms, replacing traditional radio networks with cellular networks. Its critical concern is uptime. Find out how they've used Oracle Solaris, Netra SPARC T4, and Oracle Solaris Cluster, including Oracle Solaris ZFS and Zones, for their Oracle Database deployments to improve reliability and drive down cost. 3:15 PM - Technical Panel: Developing High Performance Applications on Oracle Solaris(CON7196, Marriott Marquis - Golden Gate C2) Engineers from the Oracle Solaris, Oracle Database, and Oracle Tuxedo development teams, and Oracle ISV Engineering discuss how they develop high-performance enterprise applications that take advantage of Oracle's SPARC and x86 servers, with Oracle Solaris Studio and new Oracle Solaris 11 features. Topics will include developer tools, parallel frameworks, best practices, and methodologies, as well as insights and case studies on parallelizing and optimizing application performance on Oracle Solaris. Bring your best questions! 3:15 PM -  x86 Power Management with Oracle Solaris: Current State, Opportunities, and Future(CON6271, Moscone West 2012) Another option for this time slot: learn about how Intel Xeon and Oracle Solaris work together to reduce server power consumption. This presentation addresses some of the recent power management improvements in Oracle Solaris, opportunities to further improve energy efficiency, and some future directions for Oracle Solaris power management.

    Read the article

  • Tiny program to register work hours

    - by amin
    Hi dear ubuntu users. I'm searching for a tiny application to register my working hours so when I come to work and power on my pc it register my entrance and as a power off my pc it register me left. I know it's as simple as adding a note in gedit but I want it automated, phproject has a timer application as you start a task you push start and as you finish calculate time to register fot task , I'm searching for such small timer. thanks

    Read the article

  • System freezes while not in use, how do I fix this?

    - by PHLAK
    Bare with me, the following is a bit winded. I have Ubuntu 10.10 Desktop 64-bit installed on my laptop and up until a few weeks ago it has been running great. Then one day, while I was not using the laptop it froze. I was logged in as my user but had locked the screen locked and closed the lid. I didn't notice that it had frozen until I opened the lid and wiggled the mouse to try and log in. The screen remained black and I got no response. I immediately tried Alt + F2, F3, F4, etc. but got no response. The only thing I could do was hold the power button to power off the machine. The freezing has happened as quickly as within 10-20 minutes of the system being logged off and lid closed and as long as 4-6 hours. My machine is NOT configured to go into standby when plugged in and this has happened both on AC power and battery. Troubleshooting I have performed: I uninstalled programs I knew that I had installed between when it was working fine and having problems. Those programs were CrashPlan, Shutter and Conky. After uninstalling ALL of these programs the freezing still occurs. Next, I decided to SSH into the machine from my desktop and leave an htop and tail of the syslog running. Here are screenshots of the last thing shown on both when the system froze: htop, syslog Here is a dump of my syslog after another freeze. The freeze happened at 9:14 and I didn't notice it until about 10 minutes later and rebooted, hence the 10 minute gap from 9:14 to 9:24. In the above syslog dump I noticed a lot of NVRM: os_raise_smp_barrier(), invalid context! and upon investigating that message learned it was from the proprietary Nvidia driver I had installed. Thinking this could be part of the problem I uninstalled the Nvidia driver and reverted to using the Nouveau driver. The computer still froze after a few hours. Lastly, thinking the problem could be caused by overheating I used compressed air to blow out any dust in the CPU vents and all other openings on the laptop. None of the above troubleshooting has helped and the freezing still occurs. What other steps can I take to troubleshoot and/or fix this problem? Note: Yesterday X started to eat up a lot of CPU power and eventually froze my system while I was forwarding an X session over SSH (from another PC to my laptop). I'm unsure if this is related or not as it doesn't match any of the symptoms of the problem above. Aside from this, the system has never frozen while in use, even under heavy load. EDIT: I just ran Memtest86+ and it made it through two passes without any errors. Just eliminating possible causes here.

    Read the article

  • Ubuntu 10.04 Cant Adjust brightness on my lenevo Thinkpad?

    - by Mo.
    I cant seem to be able to adjust the brightness on my think-pad laptop running Ubuntu 10.04. In the power management applet it shows that the power is set to 100%, but even if i try to lower it the actual screen brightness dosent change. Any ideas of how I can get around this? I tried changing the brightness from the terminal but its already set to Max brightness (however the actual screen brightness is no that bright at all). Thanks

    Read the article

  • iwconfig, iw not displaying wireless information

    - by Srivatsa Kanchi
    after fresh install to 12.10, the wireless information is not shown by both iwconfig and iw. The wireless sets up successfully and able to connect This is what i get $ iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ iw wlan0 link Not connected. $ uname -a Linux srivatsa-ThinkPad-T61 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux

    Read the article

  • Support ARMv7 instruction set in Windows Embedded Compact applications

    - by Valter Minute
    On of the most interesting new features of Windows Embedded Compact 7 is support for the ARMv5, ARMv6 and ARMv7 instruction sets instead of the ARMv4 “generic” support provided by the previous releases. This means that code build for Windows Embedded Compact 7 can leverage features (like the FPU unit for ARMv6 and v7) and instructions of the recent ARM cores and improve their performances. Those improvements are noticeable in graphics, floating point calculation and data processing. The ARMv7 instruction set is supported by the latest Cortex-A8, A9 and A15 processor families. Those processor are currently used in tablets, smartphones, in-car navigation systems and provide a great amount of processing power and a low amount of electric power making them very interesting for portable device but also for any kind of device that requires a rich user interface, processing power, connectivity and has to keep its power consumption low. The bad news is that the compiler provided with Visual Studio 2008 does not provide support for ARMv7, building native applications using just the ARMv4 instruction set. Porting a Visual Studio “Smart Device” native C/C++ project to Platform Builder is not easy and you’ll lack many of the features that the VS2008 application development environment provides. You’ll also need access to the BSP and OSDesign configuration for your device to be able to build and debug your application inside Platform Builder and this may prevent independent software vendors from using the new compiler to improve their applications performances. Adeneo Embedded now provides a whitepaper and a Visual Studio plug-in that allows usage of the new ARMv7 enabled compiler to build applications inside Visual Studio 2008. I worked on the whitepaper and the tools, with the help of my colleagues and now the results can be downloaded from Adeneo Embedded’s website: http://www.adeneo-embedded.com/OS-Technologies/Windows-Embedded (Click on the “WEC7 ARMv7 Whitepaper tab to access the download links, free registration required) A very basic benchmark showed a very good performance improvement in integer and floating-point operations. Obviously your mileage may vary and we can’t promise the same amount of improvement on any application, but with a small effort on your side (even smaller if you use the plug-in) you can try on your own application. ARMv7 support is provided using Platform Builder’s compiler and VS2008 application debugger is not able to debut ARMv7 code, so you may need to put in place some workaround like keeping ARMv4 code for debugging etc.

    Read the article

  • Ubuntu 10.04 Cant Adjust brightness on my lenovo Thinkpad?

    - by Mo.
    I cant seem to be able to adjust the brightness on my think-pad laptop running Ubuntu 10.04. In the power management applet it shows that the power is set to 100%, but even if i try to lower it the actual screen brightness dosent change. Any ideas of how I can get around this? I tried changing the brightness from the terminal but its already set to Max brightness (however the actual screen brightness is no that bright at all). Thanks

    Read the article

  • Vattenfall Accelerates Projects and Cuts Costs with AutoVue Document Visualization

    Ringhals, a Swedish nuclear power plant, part of the Vattenfall Group, produces 20 percent of the country's electricity and is the largest power station in the Nordic region. Ringhals has standardized on AutoVue for most of their engineering and asset document visualization requirements throughout their plant maintenance, design and engineering operations. As a result, they have cut IT maintenance costs, increased productivity, and improved maintenance operations.

    Read the article

  • Live from the #summit13 keynote : 2013-10-16

    - by AaronBertrand
    Early morning start here in Charlotte. I'm going to try and keep this post updated as I have new information from the keynote to share, so refresh often! 8:24 AM Bill Graziano takes the stage and welcomes us to the 15th PASS Summit. He mentions that PASS delivered over 700,000 hours of technical training in the previous fiscal year, and shows a Power BI Power Map video talking about all of the SQL Saturday accomplishments in the last few years. She introduces Amy Lewis, who wins this year's PASSion...(read more)

    Read the article

  • Start a Business With Search Engine Optimization

    If you've been up and about in the internet, you should have already noticed the power search engines hold over current surfing trends and businesses. And if you're as business-minded as you are internet-savvy, you've probably also had your nose out for business opportunities revolving around that power and money-making potential.

    Read the article

  • Total Solar Eclipse 13/November/2012 - update

    - by TATWORTH
    Panasonic Eclipse Live will start their broadcast at 18:30 UT tonight at https://www.facebook.com/PanasonicEclipseLive/app_435671416492320Alternative URLs are http://www.ustream.tv/channel/panasonic-eclipse-live-by-solar-power-1 and http://www.ustream.tv/channel/panasonic-eclipse-live-by-solar-power-2/collection/744e86aa753e(The start time is 04:30 by local Australian time and will be the 14/November for them.)

    Read the article

  • Calculating missile trajectory around orbits before shooting [closed]

    - by Onofrio
    Possible Duplicate: Calculating missile trajectory around orbits before shooting I'm building a game with Unity3D. It's a Gravity Wars clone. Both player and AI turrets shoot missiles at each other (giving an Angle and a Power variables), trying not to crash missiles on planets. But here's my question: how do I make AI calculate power and angle before shooting his missile, considering a planet's gravity too?

    Read the article

  • Rugged railroad computer runs Linux

    <b>LinuxDevices:</b> "Kontron is readying an Intel Atom Z530-based box computer designed for rugged railway applications. The MicroSpace MPCX28R Railway Box PC is protected for railway use with EN50155 certification, TX compliance, extended temperature support, 1.5kV isolated power, and M12 connectors for Fast Ethernet, USB, and power..."

    Read the article

  • Installing Ubuntu in EFI mode Cant go beyond GRUB Menu

    - by Vulcan
    I created a LiveUSB of Ubuntu 12.04.3 LTS using Pendrive Linux. -Created a separate 30GB partition using Windows 8 Disk Management -Disabled Secure Boot (Didn't find an option to disable EFI boot) -Disabled Fast Startup The laptop starts the GRUB menu shows up but it doesn't go beyond that no matter what option i choose. After choosing any option the screen goes blank but the power is still on i can see the power light. My laptop is HP-n012tx processor- Intel i5 4200U Video Card- 2GBnVidia 740M The GRUB menu i see http://i.stack.imgur.com/buEAn.png

    Read the article

  • TCP/IP RST being sent differently in different browsers.

    - by Brian
    On Mac OS X (10.6), if I start a YouTube video download and pull the Ethernet cable for 5 or so seconds, then plug it back in, I get varying results depending on the browser. With Opera and Chrome, after I plug the cable back in the video continues to load. But with Safari and Firefox, it never does. Using Wireshark to look at the traffic, I found that Opera and Chrome simply ACK the first packet from YouTube after the cable has been plugged back in, but Safari and Firefox set the RST flag (0x4) in the TCP header and no more traffic follows. I can put a HUB in between the machine and the internet connection, the problem goes away and all four browsers continue loading the video when the cable is plugged back into the HUB. Again, looking at the Wireshark logs, it's evident that the machine doesn't see the Mulitcast connection close and there is simply a delay in the packets flowing through. So it seems that if Safari and Firefox sees a Multicast connection close, and then later see data on that same connection, they will send a RST. My question is why? What is the correct course of action, and why are 2/4 browsers doing it one way, while the other 2/4 are doing it another way? Is there somewhere in the code that I can see where this is happening in Firefox, for instance? Thank you very much.

    Read the article

  • CHKDSK: What option DOES NOT delete files and turn them into .chk files?

    - by CHKDSKuser
    I had a recent power outage while using my computer, with a 1TB hard drive being directly accessed as the power went out. When the power came back on, and I rebooted my computer, one of my 1TB hard drives would not register with WinXP SP3, and showed a Total Space of 0, and an Available Space of 0. The file system (NTFS) also did not register...every entry for the drive was either blank or zeroed. My assumption is that the file tables were damaged/corrupted because the drive was being directly accessed when the power went out. After doing some research, I ran CHKDSK with whatever default options it runs with (I'm not sure what they are as I didn't see them displayed). Upon completion of CHKDSK, the drive registered with WinXP as a 1TB hard drive, with an accurately-reflected amount of available space. But CHKDSK also deleted about 16GB of files from their original directories, and changed them all into sequentially-named *.chk files. My question is how can CHKDSK be run in a situation like mine where the file tables needed to be restored, but without having CHKDSK delete any files from their original directories, even if they may be damaged/corrupt? I'd simply like to be able to run CHKDSK and have it restore the file tables, and repair bad sector damage, as it did, but not have it do anything else such as delete files and convert them to CHK files. Any ideas? Or is there a CHKDSK alternative that can perform the same functions without the file deletions?

    Read the article

  • Disabling CPU management

    - by Tiffany Walker
    If I add the following processor.max_cstate=0 to the kernel command line for boot up, does that disable all CPU power management and throttling? I also found: http://www.experts-exchange.com/OS/Linux/Administration/A_3492-Avoiding-CPU-speed-scaling-in-modern-Linux-distributions-Running-CPU-at-full-speed-Tips.html The link talks of Change CPU governor from 'ondemand' to 'performance' for all CPUs/cores and disabling kondemand from kernel. Server is for web hosting UPDATES: 2.6.32-379.1.1.lve1.1.7.6.el6.x86_64 #1 SMP Sat Aug 4 09:56:37 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux . # dmidecode 2.11 SMBIOS 2.6 present. 74 structures occupying 2878 bytes. Table at 0x0009F000. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: American Megatrends Inc. Version: 1.0c Release Date: 05/27/2010 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 4096 kB Characteristics: ISA is supported PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 kB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Targeted content distribution is supported BIOS Revision: 8.16 Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: 0123456789 UUID: 49434D53-0200-9033-2500-33902500D52C Wake-up Type: Power Switch SKU Number: To Be Filled By O.E.M. Family: To Be Filled By O.E.M. Handle 0x0002, DMI type 2, 15 bytes Base Board Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: VM11S61561 Asset Tag: To Be Filled By O.E.M. Features: Board is a hosting board Board is replaceable Location In Chassis: To Be Filled By O.E.M. Chassis Handle: 0x0003 Type: Motherboard Contained Object Handles: 0 Handle 0x0003, DMI type 3, 21 bytes Chassis Information Manufacturer: Supermicro Type: Sealed-case PC Lock: Not Present Version: 0123456789 Serial Number: 0123456789 Asset Tag: To Be Filled By O.E.M. Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00000000 Height: Unspecified Number Of Power Cords: 1 Contained Elements: 0

    Read the article

  • How do you get Windows 7 to show time remaining in the battery meter?

    - by MrDaniel
    Running Microsoft Windows 7 Home Premium on a HP Laptop. The system tray power meter never shows the time remaining in the system tray. Only really ever show a percentage remaining number as pictured. The windows help documentation on the "battery meter" seems to indicate that it should display a time remaining indicator, is this accurate? How accurate is the battery meter? The accuracy of what the battery meter reports—what percentage of a full charge remains and how long you can use your laptop before you must plug it in—depends on several factors. Most of these factors fall into the following two categories: What you use the laptop for. Because some activities drain the battery faster than others (for example, watching a DVD consumes more power than reading and writing e-mail), alternating between activities that have significantly different power requirements changes the rate at which your laptop uses battery power. This can vary the estimate of how much battery charge remains. Battery hardware and sensor circuitry. Newer, "smart" batteries are equipped with circuitry that calculates the measurements of charge remaining and reports the information to the battery meter. Older batteries use less sophisticated circuitry and might be less accurate.

    Read the article

  • Dual Xeon Server voltages are low

    - by Mindflux
    I've got a whitebox server running CentOS 5.7. It's a Dual Xeon 5620, 24GB of RAM. The mainboard is a SuperMicro X8DT6-F and the chassis is a SC825TQ-R720LPB. Dual 720W Power supplies. We had a big power outage a couple weeks back that took down everything, I don't have any pre-power outage figures for this server, and the only reason I noticed these is because when I was bringing up the servers I was checking them out with more scrutiny than usual. http://i.imgur.com/rSjiw.png (Image of voltage readings) As you can see, CPU1 DIMM is low, +3.3V is high, 3.3VSB is high, +5v is high, +12v is REAL LOW (out of normal 5% (plus/minus))... and VBAT is off the charts. With my whitebox VAR we've tried the following: Swap out PSU with another server I have with the same PSUs. Try different power cord Update BMC/IPMI firmware in case readings were wrong (They aren't) Update BIOS Try different PDU Try a different outlet and/or circuit Replaced Voltage Regulator Unit At this point, the only thing we haven't done, seemingly is replace the mainboard.. which is what the next step will be unless something else shines some light on the situation. I should mention the system is rock solid otherwise which is a surprise given the 12v voltage is that far off.

    Read the article

  • cisco 2900xl - SNMP - Get mac address of device connected to an interface

    - by ankit
    Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

    Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >