Search Results

Search found 4691 results on 188 pages for 'ran biron'.

Page 68/188 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• Hibernate speed, and hard drive temperature

  - by cometbill

  My computer is taking in the region of 4 minutes or so, to hibernate 4GB of RAM. Also, resting my hand on the top of it is rather hot to the touch, so I ran CrystalDisk Info and that is reporting a temperature of 49 degrees C. I It's a Western Digital 5400 rpm drive, I've had it in the laptop since I bought it for most of the 2.75 years I've had it. Power on Count is 1219 Power on Hours is 3940 hours Boot up time is quicker than resuming from hibernate, too. Is there anything I can / should check ? Advice is greatly appreciated.

  Read the article

• installing latest apache on centos

  - by fivelitresofsoda

  hi, I'm trying to install the newest version of apache on my centos server. I did the following: Download $ wget http://httpd.apache.org/path/to/latest/version/ Extract $ gzip -d httpd-2_0_NN.tar.gz $ tar xvf httpd-2_0_NN.tar Configure $ ./configure Compile $ make Install $ make install Test $ PREFIX/bin/apachectl start And that all worked except the last step, when i type apachectl start it says 'command not found'. I ran this command from /usr/local/apache2/bin/ where it is installed but no cigar. Any idea what i am doing wrong? Thanks.

  Read the article

• What about IPv4 class E?

  - by Luc

  IPv4's class E network (240.0.0.0/4) contains 268 million addresses. Despite the advertisements for IPv6, claiming we have ran out of address space, this block ironically still claims to be "Reserved for future use". Why hasn't this block been freed up yet? Of course, IPv6 should be promoted instead of freeing up more IPv4 addresses, but we've seen the address shortage coming for years. There has even been a time they weren't sure there was enough time to develop IPv6 before we would run out of addresses. Why didn't they free up this block already? And is there any chance these addresses will be used in the future, like when IPv6 is fairly widely implemented but we still need IPv4 for backwards compatibility? It will be phased out regardless, but then ISPs don't have to employ NAT for IPv4 compatibility.

  Read the article

• Windows undetectable after interrupted chkdsk

  - by Felthragar

  I have a computer that is running Windows XP. For some reason, the other day it wouldn't start giving me the following message: "ntoskrnl.exe is missing or corrupt" So I put the XP disc in the tray and fired up the repair console and ran the following: chkdsk /r It was on for about eight hours and it got to about 52% I believe. Then there was a power outage and the computer shut down (obviously). Today when I was booting it, it isn't even detecting there's an OS anymore. If I boot the computer with no cd in the tray it says: "Reboot and select a proper Boot device or Insert Boot Media in selected Boot device and press a key" If I run the repair console, or the xp installation program it isn't finding any OS installations. Any ideas on what to do next? Any help is appreciated. Thanks! Update: After turning boot-time diagnostics on, I got this message when booting without cd (instead of the previous one): "Couldn't open drive multi(0)disk(0)rdisk(0)partition(2)"

  Read the article

• Stuck GhostScript processes, how to debug?

  - by Jonathan

  Having a problem with Ghostscript processes that don't end. This does not happen often, probably once every 3 weeks we see this issue with 1-3 processes. Running CentOS 6.4 on a VPS from Rackspace. We use PrinceXML to generate PDFs which uses GhostScript to handle fonts. Here's an image of top: http://i.stack.imgur.com/J9D7D.jpg As you can see those two processes are using a lot of resources, I haven't killed them yet in hopes someone can help me diagnose. I'm a developer not a server admin so I have a basic knowledge of *nix but no clue on how to fix this. Installed strace and ran it on each process with the following command: strace -p 20619 -s 80 -o gs.txt Left it for 5m, gs.txt is empty? Thanks in advance!

  Read the article

• sharepoint 2007 access denied when accessing user profiles via ssp

  - by user22215

  Guys I have a really strange problem in regards to sharepoint mysites today I go into user profiles and properties in order to setup a property all of a sudden I get access denied. First off I know that I'm logged in with the correct account after the access denied I decided to click on personalization services and permissions I than get An unhandled exception occurred in the user interface.Exception Information: Cannot complete this action. I'm not seeing anything in the server application logs either. So have any of you guys seen this before is there some kind of way to grant a user account the manage profiles right permission using stsadm. BTW all other fucntions of the ssp are working fine so my question is if the user profiles and my sites of a ssp tanks how do you repair that portion of the ssp? BTW the user accounts that I'm using are site collection owners and also they have full control at the web application level. I actually ran across this interesting post but this does not really help my problem. http://blog.tylerholmes.com/2008/09/access-denied-for-site-collection.html

  Read the article

• pyexiv2 build error src/exiv2wrapper.hpp:32:29: error: exiv2/preview.hpp: No such file or directory

  - by Jake

  The other day I used apt-get install python-pyexiv2 on my ubuntu server, but it seems to have given me an old version. It's not compatible with the code I wrote in my local development environment so I'd like to update it. I downloaded the latest tar.gz from the website, extracted it and ran scons as per the readme. But it will not build, I get the error src/exiv2wrapper.hpp:32:29: error: exiv2/preview.hpp: No such file or directory I've also user apt-get to install libboost-python-dev and libexiv2-dev Can anyone help me on this?

  Read the article

• Windows 8 Start Screen: Show programs in order of most frequently used

  - by Johnny W

  For me the Windows 8 Start Screen is just a great bit version of the old Start Menu, but unlike the Start Menu, it doesn't seem to order programs by frequency of use? Consider the following: While I DO use Chrome, Steam, and iTunes a lot. I've never ran Adobe Media Encoder, nor Adobe Extension Manager, nor Acrobat Distiller, or indeed most of the things on that list! Or there a way to change sorting to most frequently clicked on? Or perhaps even create FOLDERS in which to group items (e.g. "Adobe Apps" or "Games" or "Microsoft Office"?). Dragging them one at a time takes an age!

  Read the article

• Exim: Change sender address when sending mails out of local network

  - by Esa Varemo

  We have a working exim setup at a site, where users can send and receive mails. We are trying to setup a server to send some warnings and errors using email to an address that is outside the local network. The problem is: The program that sends the mails sends them using the username it runs under and the local hostname of the server. This cause the mails to have a sender of format: [email protected]. Exim sends these mails to the ISP's SMTP server, which rejects the mails as they have an illegal or unverifiable sender (the internal address). I'm thinking I should configure exim to rewrite the sender when: - sender's domain is on the local network - receiver's domain is outside the local network I tried setting some kind of rewriting in the exim config, but did not manage to get it to work. I'd show what I have tried, but I ran out of time on the last visit to the site, and had to revert to the original version losing all the changes I tried.

  Read the article

• Installing Java 1.5 on Ubuntu?

  - by StackedCrooked

  I already have Java 1.6, but I need to test something with 1.5. I have downloaded the .bin file from http://java.sun.com/javase/downloads/index_jdk5.jsp using the Sun Download Manager. Now I want to create a deb file from this bin file: $ fakeroot make-jpkg java_ee_sdk-5_01-linux.bin Creating temporary directory: /tmp/make-jpkg.Zpm1Y7LbZ0 Loading plugins: blackdown-j2re.sh blackdown-j2sdk.sh common.sh ibm-j2re.sh ibm-j2sdk.sh j2re.sh j2sdk-doc.sh j2sdk.sh j2se.sh sun-j2re.sh sun-j2sdk-doc.sh sun-j2sdk.sh Detected Debian build architecture: i386 Detected Debian GNU type: i486-linux-gnu No matching plugin was found. Removing temporary directory: done How can I fix the "No matching plugin was found." error? Update I downloaded jdk-1_5_0_22-linux-amd64.bin from the archive page and ran Linux installer. It works fine.

  Read the article

• harddrive problem (usb external)

  - by masfenix

  Hey guys I am using a Maxtor One Touch 3 given to my by my uncle. It is connected through USB2.0 When I plug it in, XP installs it and says "the device is ready to use". But it dosnt show up on my computer. It dosn't even show up in disk mangement. I then install Acronis Disk Director (which detects it) but marks it as offline. if i try to change it to online, nothing happens. (actually the lights on the HD blink - meaning communication and goes back into offline mode). The lights on the HD return to a solid which mean "working properly". Here is a screenshot: Is there any way to extract the data off the drive? is the drive corrupt? sitll useable? edit: DISKPART screenshot: edit2: I ran Seagate diagnostic tool and this came up: Long Generic - Started 9/10/2010 6:44:36 PM Bad LBA: 0 Unable to repair Long Generic - FAIL 9/10/2010 6:46:41 PM SeaTools Test Code: 4

  Read the article

• Why it's not possible to compile on a different OS than end-user OS [closed]

  - by sameold

  I was trying to compile a php extension on Windows and ran into some trouble. I then thought it was possible to do the compilation for Windows on Linux, but turned out that wasn't possible. Can someone explain to me why compiling has to be done on the same OS? I'm trying to understand this topic, specifically because if I want to distribute something, does that mean I have to compile it on all these OSs (Windows 7, Windows Vista, Windows XP, Linux, Mac, etc. etc. etc.) So what makes it not possible to compile for one OS on another? Is it the kernel or what?

  Read the article

• Windows (7 & Vista) laptop monitor does not come back after closing lid

  - by Scott Vercuski

  I'm experiencing an issue with Windows Vista (and now Windows 7) with my laptop. When I close the laptop lid the monitor goes blank but will not come back on after I re-open the laptop. The screen stays blank and nothing that I do will get it to come back. The laptop is an HP DV9000 series. Has anyone else ran into this issue? One of the solutions I've seen online is to go into the device manager and replace the lid driver with something nonsensical (the website suggested pointing the driver at the sound recorder). This does solve the problem by disabling the lid but doesn't really resolve the root issue. I'm asking if anyone has any method I can use to debug what's going on. How do I tell if it is an operating system issue vs. a malfunction within the lid itself. I'd actually like the lid to function as it's meant to. Thank you!

  Read the article

• How to fix unstable RJ45 jacks? [closed]

  - by BeemerGuy

  This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

  Read the article

• Ubuntu+Mono+Postgres+ASP.NET 4.0. No problem?

  - by wreck_of_u

  Would this be ok? I'm an ASP.NET developer and I'm planning to build "portable" web app servers based on Atom D510 mini-ITX. I have ran Ubuntu 10 with MySQL along with a separate IIS machines (win 2k3, 2k8) before with no problems. But now I'm thinking of "packaging" a web/db server into one small, cheap machine. I thought of Ubuntu/Mono/Postgres/ASP.NET, that it would be a good idea but I'm not sure? I have not actually tried it yet. Your thoughts?

  Read the article

• PC powers up but there is no display

  - by Matthew

  I built a computer with standard components I bought from Newegg about three years ago. It ran great for 2 years and has sat powered down for the last year. I tried to power it up today and the display was blank. It powers up, lights come on, drives start spinning but there is nothing on the display. I verified that the monitor and video adapter work. I also tried the video adapter in a different slot on the mother board with no luck. What's the next thing I should try? Is the mother board shot? Thanks.

  Read the article

• Ubuntu/Linux version recommendation for HP dv6 3122TX?

  - by sanjayav

  I purchased a HP dv6 3122TX recently and after installing Ubuntu 10.10 64 bit I ran into multiple issues like, The wireless driver is not supported by Uubntu. (1) [The driver is RaLink RT3090 ] The ethernet stopped working sometimes for no reason [The driver is Realtek RTL8111/8168B ] "Corrupted low memory at ..." issue which is described as a kernel bug in Ubuntu support forums. (It started to take me to a terminal instead of the GUI and couldn't start x server after that) As I'm not an expert Ubuntu user I got fed up of all these issue and got back to Windows 7. But I need an Ubuntu installation up and running for my development work. What are your suggestions about a reasonable Ubuntu version that I should try? Or a different Linux variation? Should I stick to a 32-bit version? It'd be great anyone can give some advice on this issue.

  Read the article

• after install python 2.7.3 yum is broken

  - by user468587

  i installed libxml2-2.9.0 and libxslt-1.1.27 then yum is broken any yum command that i ran i got the result of : There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: No module named yum Please install a package which provides this module, or verify that the module is installed correctly. It's possible that the above module doesn't match the current version of Python, which is: 2.4.3 (#1, Jan 21 2009, 01:11:33) [GCC 4.1.2 20071124 (Red Hat 4.1.2-42)] If you cannot solve this problem yourself, please go to the yum faq at: http://yum.baseurl.org/wiki/Faq then i thought python version is way too old and install python 2.7.3 and install it from scratch, after some wrong trials it got worse and worse, now when i run 'python -V' i got version 'Python 2.7.3', when i run '/usr/bin/python -V', it returned 'python-2.4.3-24.el5', and no matter what i did the yum is still broken with that message. how can i get yum back? my os is: linux 2.6.18-164.11.1.el5 x86_64 GNU/Linux

  Read the article

• Centos + CPanel results in php always running as fgci, instead of cli, as expected

  - by quamis

  I'm having problems with a server configured by someone else. It uses CPanel, and it has Apache+PHP. For some reason, when running php -v as a user, i get "cli" as handler # php -v | head -n 1 PHP 5.3.27 (cli) (built: Oct 15 2013 16:06:48) If a make a PHP script with echo shell_exec("php -v | tail -n 1"), i get PHP 5.3.27 (cgi-fcgi) (built: Oct 15 2013 16:22:16) Why the cli/fcgi difference? I need to fix this so that scripts ran by the apache user would be running as "cli", not "fcgi". As a side-note, i'm not sure how php got installed, because in the package list i see another version installed, instead of the pne reported by php -v # rpm -qa | grep php [.... other packages...] cpanel-php53-5.3.17-5.cp1136.x86_64 rebuild_phpconf --current: /usr/local/cpanel/bin/rebuild_phpconf --current Available handlers: suphp dso fcgi cgi none DEFAULT PHP: 5 PHP4 SAPI: none PHP5 SAPI: dso SUEXEC: enabled RUID2: not installed redhat-release: # cat /etc/redhat-release CentOS release 6.4 (Final) possibly related to http://superuser.com/questions/665809/centos-6-4-running-php-for-root-as-cgi-fcgi-not-cli

  Read the article

• Time Machine Server on Fedora

  - by Conner Stephen McCabe

  I was just wondering if anyone knew how to/or knew of a good guide to setting up mac Time Machine backup server on a fedora 17 machine. I recently ran into an issue with my HDD and lost all of my data, so I don't want it to ever happen again, as it was quite traumatising, haha! I just want to be able to back all of my data up on my fedora machine from my mac, at scheduled times when I connect to my home network. If anyone could help, it would be fantastic, I searched around on google, but all of the ones I found were for older distros. Thanks guys!

  Read the article

• Windows 7 upgrade advisor issue

  - by Groo

  I am preparing to migrate a pretty old XP machine to Windows 7. I ran the Windows 7 Upgrade Advisor and got a couple of smaller issues (low 512Mb RAM complaints and similar stuff). Apart from that, everything else was shown as compatible, including my old ATI Radeon 9550/X1050 card: ATI Radeon 9550/X1550 Series: This device is compatible with Windows 7. The thing that concerns me is that people around the web seem to be unable to actually find a Windows 7 driver for this card. Even the ATI web page states that this is a legacy device: If the user chooses to, they can install the ATI Catalyst Windows Vista graphics driver under Windows 7. [...] Using the ATI Catalyst Windows Vista driver under Windows 7 is not officially supported by AMD [...] Should I trust the Advisor and continue with the update? Does this mean Microsoft will provide at least a generic driver which will allow hardware acceleration with this card?

  Read the article

• INtel SSD RAID Trim

  - by Mike Pateras

  I just found this article, that says that Intel now supports Trim for SSD RAIDs. It links to this download page. I'm pretty excited about that, but I'm a little confused. There seem to be two sets of drivers, an executable and something that's bootable. I ran the executable. Is that just to apply the drivers to my system now, and are the bootable drivers so that if I re-format, I won't have to re-run everything? Do I need to do both? And is there a way to check if it worked? I'm running an i7 in Windows 7 (ASUS P6T Deluxe Motherboard), if that's significant.

  Read the article

• No longer able to run photo software on XP

  - by Peter

  I have Olympus Master 2 and Photoimpression 6 on my system which is running with XP Pro. Both programmes ran fine till recently and neither now works. I have run Avira and AVG anti virus (only one loaded at a time), Superantispyware, Spybot and Malwarebytes and removed the usual dross but no help. I have also uninstalled and reinstalled both several times but again no help. Both programmes load but the Olympus one immediately passes to the usual 'its met a problem and needs to close'...Photoimpression loads fully but as soon as I go to the edit screen it gives the same message. I have tried another profile to no avail. Any idea why this is and what the solution is??

  Read the article

• Problem with running a program from flashdrive

  - by rajivpradeep

  I have a USB drive with two partitions in it, one hidden and one normal. I have an application which swaps the memory and runs the flash application in hidden zone. The problem is that the application works fine on Windows 7 and when run on Win XP, it swaps the partitions but doesn't run the flash applications but just keeps running in the background. I can see it in task manager. But, when I copy the application to desktop and run, it runs with no glitch. I was facing the same problem on Win 7 too, but it was running as required when I ran it using "Run in XP mode" and then I applied a SHIM and is running since then as required. The application is built using VC++ 2008. What might be the problem?

  Read the article

• Cant access EC2 hosted website

  - by Himanshu Page

  For some reason, I am unable to access our website www.doccaster.com (Bad request nginx). We are hosted on amazon EC2 with elastic ip associated to it. The weird part is a) I can access it through the public dns url http://ec2-184-73-195-180.compute-1.amazonaws.com b) My co founder who is located in another city can access it via www.doccaster.com. I observed that my instance was failing reachability check, so I launched a new one and assigned it the the elastic ip. I tried to ping the ip address 184.73.195.180 from my machine but no success. Any help will be really appreciated. More details I ran the following command on my server netstat -lntp | grep -E 'apache|httpd' and it displays :::80 for httpd . Is this accurate ? Should it be 0:0:0:80 ? or doesnt matter?

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >