Search Results

Search found 7312 results on 293 pages for 'render quality'.

Page 68/293 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• Randomly displayed flashing lines, no response to all shortcuts, just power off. [syslog included]

  - by B. Roland

  Hello! I have an old machine, and I want to use for that to learn employees how to use Ubuntu, and to be easyer to switch from Windows. I've been installed 10.04, and updated, but this strange stuff is happend. Graphical installion failed, same strange thing. With alternate workd. Sometimes, when I boot up, a boot message displayed: Keyboard failure..., often diplayed after reboot, and after shutdown, when I haven't plugged off from AC. I replaced the keyboard yet, same failure... If I powered off, and plugged off from AC, no keyboard problems displayed in boot time. Details Configuration: Dell OptiPlex GX60 - in original cover, no changes. 256 MB DDR 166 MHz Intel® Celeron® Processor 2.40 GHz Dell 0C3207 Base Board I know, that is not enough, but I have three other Nec compuers, with nearly similar config, and they works well with 9.10, 10.04, 10.10. Live CDs I've been tried with 10.04 and 10.10, but the problem is displayed too. With 9.10 no strange things displayed, but it froze, during a simple apt-get install. Syslog An error loop is logged here, but I paste the whole startup and error lines. The flashing lines are displayed sometimes immediately after login, but sometimes after 10 minutes, but once occured, that nothing happend. Strange thing is displayed immediately after login: here. An other boot, after some minutes, strange lines, and loop in log appeard: here. The loop should be that: Jan 23 00:20:08 machine_name kernel: [ 46.782212] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 23 00:20:08 machine_name kernel: [ 47.100033] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 23 00:20:08 machine_name kernel: [ 47.100045] render error detected, EIR: 0x00000000 Jan 23 00:20:08 machine_name kernel: [ 47.101487] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 16 at 9) Jan 23 00:20:11 machine_name kernel: [ 49.152020] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 23 00:20:11 machine_name gdm-simple-slave[1245]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Jan 23 00:20:11 machine_name acpid: client 1239[0:0] has disconnected Jan 23 00:20:11 machine_name acpid: client connected from 1247[0:0] Jan 23 00:20:11 machine_name acpid: 1 client rule loaded UPDATE Added syslog things: before errors, error loop, the complete shutdown(after the big updates): Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully called chroot. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully dropped privileges. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully limited resources. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Watchdog thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Canary thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully made thread 1337 of process 1337 (n/a) owned by '1001' high priority at nice level -11. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Supervising 1 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1345 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 2 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1349 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 3 threads of 1 processes of 1 users. Jan 28 20:40:37 machine_name pulseaudio[1337]: ratelimit.c: 2 events suppressed Jan 28 20:41:33 machine_name AptDaemon: INFO: Initializing daemon Jan 28 20:41:44 machine_name kernel: [ 167.691563] lo: Disabled Privacy Extensions Jan 28 20:47:33 machine_name AptDaemon: INFO: Quiting due to inactivity Jan 28 20:47:33 machine_name AptDaemon: INFO: Shutdown was requested Jan 28 20:59:50 machine_name kernel: [ 1253.840513] lo: Disabled Privacy Extensions Jan 28 21:17:02 machine_name CRON[1874]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 21:17:38 machine_name kernel: [ 2321.553239] lo: Disabled Privacy Extensions Jan 28 22:07:44 machine_name kernel: [ 5327.840254] lo: Disabled Privacy Extensions Jan 28 22:17:02 machine_name CRON[2665]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 22:57:03 machine_name kernel: [ 8286.641472] lo: Disabled Privacy Extensions Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 23:07:42 machine_name kernel: [ 8925.272030] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:07:42 machine_name kernel: [ 8925.272048] render error detected, EIR: 0x00000000 Jan 28 23:07:42 machine_name kernel: [ 8925.272093] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171453 at 171452) Jan 28 23:07:45 machine_name kernel: [ 8928.868041] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:10 machine_name acpid: client 925[0:0] has disconnected Jan 28 23:08:10 machine_name acpid: client connected from 8127[0:0] Jan 28 23:08:10 machine_name acpid: 1 client rule loaded Jan 28 23:08:11 machine_name kernel: [ 8955.046248] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:12 machine_name kernel: [ 8955.364016] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:12 machine_name kernel: [ 8955.364027] render error detected, EIR: 0x00000000 Jan 28 23:08:12 machine_name kernel: [ 8955.364407] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171457 at 171452) Jan 28 23:08:14 machine_name kernel: [ 8957.472025] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:14 machine_name acpid: client 8127[0:0] has disconnected Jan 28 23:08:14 machine_name acpid: client connected from 8141[0:0] Jan 28 23:08:14 machine_name acpid: 1 client rule loaded Jan 28 23:08:15 machine_name kernel: [ 8958.671722] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:15 machine_name kernel: [ 8958.988015] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:15 machine_name kernel: [ 8958.988026] render error detected, EIR: 0x00000000 Jan 28 23:08:15 machine_name kernel: [ 8958.989400] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171459 at 171452) Jan 28 23:08:16 machine_name init: tty4 main process (848) killed by TERM signal Jan 28 23:08:16 machine_name init: tty5 main process (856) killed by TERM signal Jan 28 23:08:16 machine_name NetworkManager: nm_signal_handler(): Caught signal 15, shutting down normally. Jan 28 23:08:16 machine_name init: tty2 main process (874) killed by TERM signal Jan 28 23:08:16 machine_name init: tty3 main process (875) killed by TERM signal Jan 28 23:08:16 machine_name init: tty6 main process (877) killed by TERM signal Jan 28 23:08:16 machine_name init: cron main process (890) killed by TERM signal Jan 28 23:08:16 machine_name init: tty1 main process (1146) killed by TERM signal Jan 28 23:08:16 machine_name avahi-daemon[644]: Got SIGTERM, quitting. Jan 28 23:08:16 machine_name avahi-daemon[644]: Leaving mDNS multicast group on interface eth0.IPv4 with address 10.238.11.134. Jan 28 23:08:16 machine_name acpid: exiting Jan 28 23:08:16 machine_name init: avahi-daemon main process (644) terminated with status 255 Jan 28 23:08:17 machine_name kernel: Kernel logging (proc) stopped. Jan 28 23:09:00 machine_name kernel: imklog 4.2.0, log source = /proc/kmsg started. Jan 28 23:09:00 machine_name rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="516" x-info="http://www.rsyslog.com"] (re)start Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's groupid changed to 103 Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's userid changed to 101 Jan 28 23:09:00 machine_name rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] When I hit the On/Off button, the system shuts down normally. May be it a hardware problem, but I don't know... Can you say something useful to solve my problem?

  Read the article

• Help understanding some OpenGL stuff

  - by shinjuo

  I am working with some code to create a triangle that moves with arrow keys. I want to create a second object that moves independently. This is where I am having trouble, I have created the second actor, but cannot get it to move. There is too much code to post it all so I will just post a little and see if anyone can help at all. ogl_test.cpp #include "platform.h" #include "srt/scheduler.h" #include "model.h" #include "controller.h" #include "model_module.h" #include "graphics_module.h" class blob : public actor { public: blob(float x, float y) : actor(math::vector2f(x, y)) { } void render() { transform(); glBegin(GL_TRIANGLES); glVertex3f(0.25f, 0.0f, -5.0f); glVertex3f(-.5f, 0.25f, -5.0f); glVertex3f(-.5f, -0.25f, -5.0f); glEnd(); end_transform(); } void update(controller& c, float dt) { if (c.left_key) { rho += pi / 9.0f * dt; c.left_key = false; } if (c.right_key) { rho -= pi / 9.0f * dt; c.right_key = false; } if (c.up_key) { v += .1f * dt; c.up_key = false; } if (c.down_key) { v -= .1f * dt; if (v < 0.0) { v = 0.0; } c.down_key = false; } actor::update(c, dt); } }; class enemyOne : public actor { public: enemyOne(float x, float y) : actor(math::vector2f(x, y)) { } void render() { transform(); glBegin(GL_TRIANGLES); glVertex3f(0.25f, 0.0f, -5.0f); glVertex3f(-.5f, 0.25f, -5.0f); glVertex3f(-.5f, -0.25f, -5.0f); glEnd(); end_transform(); } void update(controller& c, float dt) { if (c.left_key) { rho += pi / 9.0f * dt; c.left_key = false; } if (c.right_key) { rho -= pi / 9.0f * dt; c.right_key = false; } if (c.up_key) { v += .1f * dt; c.up_key = false; } if (c.down_key) { v -= .1f * dt; if (v < 0.0) { v = 0.0; } c.down_key = false; } actor::update(c, dt); } }; int APIENTRY WinMain( HINSTANCE hInstance, HINSTANCE hPrevInstance, char* lpCmdLine, int nCmdShow ) { model m; controller control(m); srt::scheduler scheduler(33); srt::frame* model_frame = new srt::frame(scheduler.timer(), 0, 1, 2); srt::frame* render_frame = new srt::frame(scheduler.timer(), 1, 1, 2); model_frame->add(new model_module(m, control)); render_frame->add(new graphics_module(m)); scheduler.add(model_frame); scheduler.add(render_frame); blob* prime = new blob(0.0f, 0.0f); m.add(prime); m.set_prime(prime); enemyOne* primeTwo = new enemyOne(2.0f, 0.0f); m.add(primeTwo); m.set_prime(primeTwo); scheduler.start(); control.start(); return 0; } model.h #include <vector> #include "vec.h" const double pi = 3.14159265358979323; class controller; using math::vector2f; class actor { public: vector2f P; float theta; float v; float rho; actor(const vector2f& init_location) : P(init_location), rho(0.0), v(0.0), theta(0.0) { } virtual void render() = 0; virtual void update(controller&, float dt) { float v1 = v; float theta1 = theta + rho * dt; vector2f P1 = P + v1 * vector2f(cos(theta1), sin(theta1)); if (P1.x < -4.5f || P1.x > 4.5f) { P1.x = -P1.x; } if (P1.y < -4.5f || P1.y > 4.5f) { P1.y = -P1.y; } v = v1; theta = theta1; P = P1; } protected: void transform() { glPushMatrix(); glTranslatef(P.x, P.y, 0.0f); glRotatef(theta * 180.0f / pi, 0.0f, 0.0f, 1.0f); //Rotate about the z-axis } void end_transform() { glPopMatrix(); } }; class model { private: typedef std::vector<actor*> actor_vector; actor_vector actors; public: actor* _prime; model() { } void add(actor* a) { actors.push_back(a); } void set_prime(actor* a) { _prime = a; } void update(controller& control, float dt) { for (actor_vector::iterator i = actors.begin(); i != actors.end(); ++i) { (*i)->update(control, dt); } } void render() { for (actor_vector::iterator i = actors.begin(); i != actors.end(); ++i) { (*i)->render(); } } };

  Read the article

• Expectations + Rewards = Innovation

  - by D'Arcy Lussier

  “Innovation” is a heavy word. We regard those that embrace it as “Innovators”. We describe organizations as being “Innovative”. We hold those associated with the word in high regard, even though its dictionary definition is very simple: Introducing something new. What our culture has done is wrapped Innovation in white robes and a gold crown. Innovation is rarely just introducing something new. Innovations and innovators are typically associated with other terms: groundbreaking, genius, industry-changing, creative, leading. Being a true innovator and creating innovations are a big deal, and something companies try to strive for…or at least say they strive for. There’s huge value in being recognized as an innovator in an industry, since the idea is that innovation equates to increased profitability. IBM ran an ad a few years back that showed what their view of innovation is: “The point of innovation is to make actual money.” If the money aspect makes you feel uneasy, consider it another way: the point of innovation is to <insert payoff here>. Companies that innovate will be more successful. Non-profits that innovate can better serve their target clients. Governments that innovate can better provide services to their citizens. True innovation is not easy to come by though. As with anything in business, how well an organization will innovate is reliant on the employees it retains, the expectations placed on those employees, and the rewards available to them. In a previous blog post I talked about one formula: Right Employees + Happy Employees = Productive Employees I want to introduce a new one, that builds upon the previous one: Expectations + Rewards = Innovation  The level of innovation your organization will realize is directly associated with the expectations you place on your staff and the rewards you make available to them. Expectations We may feel uncomfortable with the idea of placing expectations on our staff, mainly because expectation has somewhat of a negative or cold connotation to it: “I expect you to act this way or else!” The problem is in the or-else part…we focus on the negative aspects of failing to meet expectations instead of looking at the positive side. “I expect you to act this way because it will produce <insert benefit here>”. Expectations should not be set to punish but instead be set to ensure quality. At a recent conference I spoke with some Microsoft employees who told me that you have five years from starting with the company to reach a “Senior” level. If you don’t, then you’re let go. The expectation Microsoft placed on their staff is that they should be working towards improving themselves, taking more responsibility, and thus ensure that there is a constant level of quality in the workforce. Rewards Let me be clear: a paycheck is not a reward. A paycheck is simply the employer’s responsibility in the employee/employer relationship. A paycheck will never be the key motivator to drive innovation. Offering employees something over and above their required compensation can spur them to greater performance and achievement. Working in the food service industry, this tactic was used again and again: whoever has the highest sales over lunch will receive a free lunch/gift certificate/entry into a draw/etc. There was something to strive for, to try beyond the baseline of what our serving jobs were. It was through this that innovative sales techniques would be tried and honed, with key servers being top sellers time and time again. At a code camp I spoke at, I was amazed to see that all the employees from one company receive $100 Visa gift cards as a thank you for taking time to speak. Again, offering something over and above that can give that extra push for employees. Rewards work. But what about the fairness angle? In the restaurant example I gave, there were servers that would never win the competition. They just weren’t good enough at selling and never seemed to get better. So should those that did work at performing better and produce more sales for the restaurant not get rewarded because those who weren’t working at performing better might get upset? Of course not! Organizations succeed because of their top performers and those that strive to join their ranks. The Expectation/Reward Graph While the Expectations + Rewards = Innovation formula may seem like a simple mathematics formula, there’s much more going under the hood. In fact there are three different outcomes that could occur based on what you put in as values for Expectations and Rewards. Consider the graph below and the descriptions that follow: Disgruntled – High Expectation, Low Reward I worked at a company where the mantra was “Company First, Because We Pay You”. Even today I still hear stories of how this sentiment continues to be perpetuated: They provide you a paycheck and a means to live, therefore you should always put them as your top priority. Of course, this is a huge imbalance in the expectation/reward equation. Why would anyone willingly meet high expectations of availability, workload, deadlines, etc. when there is no reward other than a paycheck to show for it? Remember: paychecks are not rewards! Instead, you see employees be disgruntled which not only affects the level of production but also the level of quality within an organization. It also means that you see higher turnover. Complacent – Low Expectation, Low Reward Complacency is a systemic problem that typically exists throughout all levels of an organization. With no real expectations or rewards, nobody needs to excel. In fact, those that do try to innovate, improve, or introduce new things into the organization might be shunned or pushed out by the rest of the staff who are just doing things the same way they’ve always done it. The bigger issue for the organization with low/low values is that at best they’ll never grow beyond their current size (and may shrink actually), and at worst will cease to exist. Entitled – Low Expectation, High Reward It’s one thing to say you have the best people and reward them as such, but its another thing to actually have the best people and reward them as such. Organizations with Entitled employees are the former: their organization provides them with all types of comforts, benefits, and perks. But there’s no requirement before the rewards are dolled out, and there’s no short-list of who receives the rewards. Everyone in the company is treated the same and is given equal share of the spoils. Entitlement is actually almost identical with Complacency with one notable difference: just try to introduce higher expectations into an entitled organization! Entitled employees have been spoiled for so long that they can’t fathom having rewards taken from them, or having to achieve specific levels of performance before attaining them. Those running the organization also buy in to the Entitled sentiment, feeling that they must persist the same level of comforts to appease their staff…even though the quality of the employee pool may be suspect. Innovative – High Expectation, High Reward Finally we have the Innovative organization which places high expectations but also provides high rewards. This organization gets it: if you truly want the best employees you need to apply equal doses of pressure and praise. Realize that I’m not suggesting crazy overtime or un-realistic working conditions. I do not agree with the “Glengary-Glenross” method of encouragement. But as anyone who follows sports can tell you, the teams that win are the ones where the coaches push their players to be their best; to achieve new levels of performance that they didn’t know they could receive. And the result for the players is more money, fame, and opportunity. It’s in this environment that organizations can focus on innovation – true innovation that builds the business and allows everyone involved to truly benefit. In Closing Organizations love to use the word “Innovation” and its derivatives, but very few actually do innovate. For many, the term has just become another marketing buzzword to lump in with all the other business terms that get overused. But for those organizations that truly get the value of innovation, they will be the ones surging forward while other companies simply fade into the background. And they will be the organizations that expect more from their employees, and give them their just rewards.

  Read the article

• How to filter Backbone.js Collection and Rerender App View?

  - by Jeremy H.

  Is is a total Backbone.js noob question. I am working off of the ToDo Backbone.js example trying to build out a fairly simple single app interface. While the todo project is more about user input, this app is more about filtering the data based on the user options (click events). I am completely new to Backbone.js and Mongoose and have been unable to find a good example of what I am trying to do. I have been able to get my api to pull the data from the MongoDB collection and drop it into the Backbone.js collection which renders it in the app. What I cannot for the life of me figure out how to do is filter that data and re-render the app view. I am trying to filter by the "type" field in the document. Here is my script: (I am totally aware of some major refactoring needed, I am just rapid prototyping a concept.) $(function() { window.Job = Backbone.Model.extend({ idAttribute: "_id", defaults: function() { return { attachments: false } } }); window.JobsList = Backbone.Collection.extend({ model: Job, url: '/api/jobs', leads: function() { return this.filter(function(job){ return job.get('type') == "Lead"; }); } }); window.Jobs = new JobsList; window.JobView = Backbone.View.extend({ tagName: "div", className: "item", template: _.template($('#item-template').html()), initialize: function() { this.model.bind('change', this.render, this); this.model.bind('destroy', this.remove, this); }, render: function() { $(this.el).html(this.template(this.model.toJSON())); this.setText(); return this; }, setText: function() { var month=new Array(); month[0]="Jan"; month[1]="Feb"; month[2]="Mar"; month[3]="Apr"; month[4]="May"; month[5]="Jun"; month[6]="Jul"; month[7]="Aug"; month[8]="Sep"; month[9]="Oct"; month[10]="Nov"; month[11]="Dec"; var title = this.model.get('title'); var description = this.model.get('description'); var datemonth = this.model.get('datem'); var dateday = this.model.get('dated'); var jobtype = this.model.get('type'); var jobstatus = this.model.get('status'); var amount = this.model.get('amount'); var paymentstatus = this.model.get('paymentstatus') var type = this.$('.status .jobtype'); var status = this.$('.status .jobstatus'); this.$('.title a').text(title); this.$('.description').text(description); this.$('.date .month').text(month[datemonth]); this.$('.date .day').text(dateday); type.text(jobtype); status.text(jobstatus); if(amount > 0) this.$('.paymentamount').text(amount) if(paymentstatus) this.$('.paymentstatus').text(paymentstatus) if(jobstatus === 'New') { status.addClass('new'); } else if (jobstatus === 'Past Due') { status.addClass('pastdue') }; if(jobtype === 'Lead') { type.addClass('lead'); } else if (jobtype === '') { type.addClass(''); }; }, remove: function() { $(this.el).remove(); }, clear: function() { this.model.destroy(); } }); window.AppView = Backbone.View.extend({ el: $("#main"), events: { "click #leads .highlight" : "filterLeads" }, initialize: function() { Jobs.bind('add', this.addOne, this); Jobs.bind('reset', this.addAll, this); Jobs.bind('all', this.render, this); Jobs.fetch(); }, addOne: function(job) { var view = new JobView({model: job}); this.$("#activitystream").append(view.render().el); }, addAll: function() { Jobs.each(this.addOne); }, filterLeads: function() { // left here, this event fires but i need to figure out how to filter the activity list. } }); window.App = new AppView; });

  Read the article

• Blogging locally and globally–my experience

  - by DigiMortal

  In Baltic MVP Summit 2011 there was discussion about having two blogs - one for local and another for global audience – and how to publish once written information in these blogs. There are many ways how to optimize your blogging activities if you have more than one audience and here you can find my experiences, best practices and advices about this topic. My two blogs I have to working blogs: this one here technology and programming blog for local market My local blog is almost five years old and it makes it one of the oldest company blogs in Estonia. It is still active and I write there as much as I have time for it. This blog here is active since September 2007, so it is about 3.5 years old right now. Both of these blogs are  my major hits in my MVP carrier and they have very good web statistics too. My local blog My local blog is about programming, web and technology. It has way wider target audience then this blog here has. By example, in my local blog I blog also about local events, cool new concept phones, different webs providing some interesting services etc. But local guys can find there also my postings about how to solve one or another programming problem and postings about Microsoft technologies I am playing with. This far my local blog has a lot of readers for such a small country that Estonia is. This blog has made me a lot of cool contacts and I have had there a lot of interesting discussions about different technical topics. Why I started this blog? Living in small country is different than living in big country. In small country you have less people and therefore smaller audience so you have to target more than one technical topic to find enough readers. In a same time you are still interested in your main topics and you want to reach to more people who are sharing same interests with you. Practically one day y will grow out from local market and you go global. This is how this blog was born. Was it worth to create, promote and mess with it? Every second I have put on my time to this blog has been worth of it. Thanks to this blog I have found new good friends and without them I think it is more boring to work on different problems and solutions. Defining target audiences One thing you should always do when having more than one blog is defining target audiences. If you are just technomaniac interested in sharing your stuff and make some new friends and have something to write to your MVP nomination form then you don’t have to go through complex targeting process. You can do it simple way and same effectively. Here is how I defined target audiences to my blogs: local blog – reader of my local blog is IT professional, software developer, technology innovator or just some guy who is interested in technology,   this blog – reader of this blog is experienced professional software developer who works on Microsoft technologies or software developer who is open minded and open to new technologies and interesting solutions to development problems. You can see how local blog – due to small market with less people – has wider definition for audience while this blog is heavily targeted to Microsoft technologies and specially to software development. On practical side these decisions are also made well I think because it is very hard to build up popular common IT blog. On global level it is better to target some specific niche and find readers who are professionals on your favorite topics. Thanks to this blog I have found new friends who are professional developers and I am very happy about all the discussions I have had with them. Publishing content to different blogs My local blog and this blog have some overlapping topics like .NET, databases and SEO. Due to this overlapping there is question: when I write posting to my local blog then should I have to publish same thing in my global blog? And if I write something to my global blog then should I publish same thing also in my local blog? Well, it really depends on the definition of your target audiences. If they match then of course it is good idea to translate you post and publish it also to another blog. But if you have different audiences then you may need to modify your posting before publishing it. The questions you have to answer are: is target audience interested in this topic? is target audience expecting more specific and deeper handling of this topic or are they expecting more general handling of topic? is the problem you are discussing actual for target audience or not? You have to answer these questions and after that make your decision. If you need to modify your original posting then take some time and do it. Provide quality to all your readers because they will respect you if you respect them. Cross-posting and referencing It is tempting to save time that preparing some blog post takes and if you have are done with posting in one blog it may seem like good idea to make short posting to another blog and add reference to first one where topic is discussed longer. Well, don’t do it – all your readers expect good quality content from you and jumping from one blog post to another is disturbing for them. Of course, there is problem with differences between target audiences. You may have wider target audience and some people may be interested in more specific handling of topic. In this case feel free to refer your blog you are writing in english. This is not working very well in opposite direction because almost all my global blog readers understand english but not estonian. By example, estonian language is complex one and online translating tools make very poor translations from estonian language. This is why I don’t even plan to publish postings here that refer to my local blog for more information. I am keeping these two blogs as two different worlds and if there is posting that fits well to both blogs I will write my posting to one blog and then answer previous three questions before posting same thing to another blog. Conclusion Growing out of your local market is not anything mysterious if you are living in small country. As it is harder to find people there who are interested in same topics with you then sooner or later you will start finding these new contacts from global audience. Global audience is bigger and to be visible there you must provide high quality content to your audience. It is something you will learn over time and you will learn every day something new when you are posting to your global blog. You may ask: if global blog is much more complex thing to do then is it worth to do at all? My answer is: yes, do it for sure. It is not easy thing to do when you start but if you work on your global blog and improve it over time you will get over all obstacles pretty soon. Just don’t forget one thing – content is king and your readers expect high quality from you.

  Read the article

• No method error in controller create action

  - by user2799827

  I have read a number of Q&As on SO in search of some help on this but have so far not solved my issue. I am trying to teach myself ruby/rails, and as a test project, I want to create a list of tvshows and a list of characters where each tvshow has_many characters and each character belongs_to a specific show. I am sure I am doing something basic incorrectly. Any assistance would be greatly appreciated. here is the characters controller: class CharactersController < ApplicationController before_action :set_character, only: [:show, :edit, :update, :destroy] # GET /characters # GET /characters.json def index @characters = Character.all end # GET /characters/1 # GET /characters/1.json def show end # GET /characters/new def new @character = Character.new end # GET /characters/1/edit def edit end # POST /characters # POST /characters.json def create @character = @tvshow.characters.create(params[:character]) respond_to do |format| if @character.save format.html { redirect_to @character, notice: 'Character was successfully created.' } format.json { render action: 'show', status: :created, location: @character } else format.html { render action: 'new' } format.json { render json: @character.errors, status: :unprocessable_entity } end end end # PATCH/PUT /characters/1 # PATCH/PUT /characters/1.json def update respond_to do |format| if @character.update(character_params) format.html { redirect_to @character, notice: 'Character was successfully updated.' } format.json { head :no_content } else format.html { render action: 'edit' } format.json { render json: @character.errors, status: :unprocessable_entity } end end end # DELETE /characters/1 # DELETE /characters/1.json def destroy @character.destroy respond_to do |format| format.html { redirect_to characters_url } format.json { head :no_content } end end private # Use callbacks to share common setup or constraints between actions. def set_character @character = Character.find(params[:id]) end # Never trust parameters from the scary internet, only allow the white list through. def character_params params.require(:character).permit(:first_name, :last_name, :bio) end end character model: class Character < ActiveRecord::Base belongs_to :tvshow default_scope -> { order('created_at DESC') } validates :tvshow_id, presence: true end tvshow model: class Tvshow < ActiveRecord::Base has_many :characters, dependent: :destroy end error gets returned when I attempt to create a character. here is the full trace: app/controllers/characters_controller.rb:27:in `create' actionpack (4.0.0) lib/action_controller/metal/implicit_render.rb:4:in `send_action' actionpack (4.0.0) lib/abstract_controller/base.rb:189:in `process_action' actionpack (4.0.0) lib/action_controller/metal/rendering.rb:10:in `process_action' actionpack (4.0.0) lib/abstract_controller/callbacks.rb:18:in `block in process_action' activesupport (4.0.0) lib/active_support/callbacks.rb:413:in `_run__1211653665462320621__process_action__callbacks' activesupport (4.0.0) lib/active_support/callbacks.rb:80:in `run_callbacks' actionpack (4.0.0) lib/abstract_controller/callbacks.rb:17:in `process_action' actionpack (4.0.0) lib/action_controller/metal/rescue.rb:29:in `process_action' actionpack (4.0.0) lib/action_controller/metal/instrumentation.rb:31:in `block in process_action' activesupport (4.0.0) lib/active_support/notifications.rb:159:in `block in instrument' activesupport (4.0.0) lib/active_support/notifications/instrumenter.rb:20:in `instrument' activesupport (4.0.0) lib/active_support/notifications.rb:159:in `instrument' actionpack (4.0.0) lib/action_controller/metal/instrumentation.rb:30:in `process_action' actionpack (4.0.0) lib/action_controller/metal/params_wrapper.rb:245:in `process_action' activerecord (4.0.0) lib/active_record/railties/controller_runtime.rb:18:in `process_action' actionpack (4.0.0) lib/abstract_controller/base.rb:136:in `process' actionpack (4.0.0) lib/abstract_controller/rendering.rb:44:in `process' actionpack (4.0.0) lib/action_controller/metal.rb:195:in `dispatch' actionpack (4.0.0) lib/action_controller/metal/rack_delegation.rb:13:in `dispatch' actionpack (4.0.0) lib/action_controller/metal.rb:231:in `block in action' actionpack (4.0.0) lib/action_dispatch/routing/route_set.rb:80:in `call' actionpack (4.0.0) lib/action_dispatch/routing/route_set.rb:80:in `dispatch' actionpack (4.0.0) lib/action_dispatch/routing/route_set.rb:48:in `call' actionpack (4.0.0) lib/action_dispatch/journey/router.rb:71:in `block in call' actionpack (4.0.0) lib/action_dispatch/journey/router.rb:59:in `each' actionpack (4.0.0) lib/action_dispatch/journey/router.rb:59:in `call' actionpack (4.0.0) lib/action_dispatch/routing/route_set.rb:655:in `call' rack (1.5.2) lib/rack/etag.rb:23:in `call' rack (1.5.2) lib/rack/conditionalget.rb:35:in `call' rack (1.5.2) lib/rack/head.rb:11:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/params_parser.rb:27:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/flash.rb:241:in `call' rack (1.5.2) lib/rack/session/abstract/id.rb:225:in `context' rack (1.5.2) lib/rack/session/abstract/id.rb:220:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/cookies.rb:486:in `call' activerecord (4.0.0) lib/active_record/query_cache.rb:36:in `call' activerecord (4.0.0) lib/active_record/connection_adapters/abstract/connection_pool.rb:626:in `call' activerecord (4.0.0) lib/active_record/migration.rb:369:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/callbacks.rb:29:in `block in call' activesupport (4.0.0) lib/active_support/callbacks.rb:373:in `_run__2792846465963916895__call__callbacks' activesupport (4.0.0) lib/active_support/callbacks.rb:80:in `run_callbacks' actionpack (4.0.0) lib/action_dispatch/middleware/callbacks.rb:27:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/reloader.rb:64:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/remote_ip.rb:76:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/debug_exceptions.rb:17:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/show_exceptions.rb:30:in `call' railties (4.0.0) lib/rails/rack/logger.rb:38:in `call_app' railties (4.0.0) lib/rails/rack/logger.rb:21:in `block in call' activesupport (4.0.0) lib/active_support/tagged_logging.rb:67:in `block in tagged' activesupport (4.0.0) lib/active_support/tagged_logging.rb:25:in `tagged' activesupport (4.0.0) lib/active_support/tagged_logging.rb:67:in `tagged' railties (4.0.0) lib/rails/rack/logger.rb:21:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/request_id.rb:21:in `call' rack (1.5.2) lib/rack/methodoverride.rb:21:in `call' rack (1.5.2) lib/rack/runtime.rb:17:in `call' activesupport (4.0.0) lib/active_support/cache/strategy/local_cache.rb:83:in `call' rack (1.5.2) lib/rack/lock.rb:17:in `call' actionpack (4.0.0) lib/action_dispatch/middleware/static.rb:64:in `call' railties (4.0.0) lib/rails/engine.rb:511:in `call' railties (4.0.0) lib/rails/application.rb:97:in `call' rack (1.5.2) lib/rack/lock.rb:17:in `call' rack (1.5.2) lib/rack/content_length.rb:14:in `call' rack (1.5.2) lib/rack/handler/webrick.rb:60:in `service' /Users/dariusgoore/.rvm/rubies/ruby-1.9.3-p194/lib/ruby/1.9.1/webrick/httpserver.rb:138:in `service' /Users/dariusgoore/.rvm/rubies/ruby-1.9.3-p194/lib/ruby/1.9.1/webrick/httpserver.rb:94:in `run' /Users/dariusgoore/.rvm/rubies/ruby-1.9.3-p194/lib/ruby/1.9.1/webrick/server.rb:191:in `block in start_thread'

  Read the article

• javax.servlet.ServletException: WriteText method cannot write null text

  - by Learner

  I have created a Web application using JSF+Icefaces+Richfaces+Primefaces.It is working great while I run it from eclipse as a project but When I created its WAR file and deployed in GlassFish Server then while rendering a page it is throwing this exception javax.servlet.ServletException: WriteText method cannot write null text I searched but didn't get any good solution.A quick help is highly appreciated Edit:1 I think this would be the relevant part for this <li class="page_item" id="liMasterSearch"> <!-- this is for hide (<li class="page_item hide" id="liMasterSearch"> applied to every class) --> <h:commandLink value="Search" action="#{masterRenderBean.showSimpleSearch}"></h:commandLink> </li> <li class="page_item" id="liAdvanceSearch"> <h:commandLink value="Advance Search" action="#{masterRenderBean.showADVS}"></h:commandLink> </li> Here you can see two links (1) Search and (2) Advance Search when I click on Search , It shows search page (By rendering-Actually I have included all pages in masterpage and render them on commandlink functions) <h:panelGroup rendered="#{not masterRenderBean.simpleSearch}"> <ui:include src="../../WebPages/SearchPages/MasterSearch.xhtml"></ui:include> </h:panelGroup> But When I click on Advance Search link (on which this part should render) <h:panelGroup rendered="#{not masterRenderBean.advs}"> <ui:include src="../../WebPages/SearchPages/PersonalAdvanceSearch.xhtml"/> </h:panelGroup> The browser show the above exception. NOTE: Keep in mind that this problem is occurring in deploying.It is not coming in actual application when I run it from eclipse from code EDIT:2 I found in server logs that this exception is coming due to acefaces and this portion of code <ace:autoCompleteEntry id="txtplaceofbirth" rows="10" autocomplete="false" minChars="2" width="150" value="#{inputPersonal.selectedplcofBirth}" filterMatchMode="none" valueChangeListener="#{inputPersonal.valueChangeEventCity}"> <f:selectItems value="#{inputPersonal.cities}"/> </ace:autoCompleteEntry></h:outputFormat> is messing up.Any idea Why this is hapening? Edit #3: Here is the full tack trace of exception [#|2012-11-19T09:55:48.026+0500|SEVERE|glassfish3.1.2|javax.enterprise.system.std.com.sun.enterprise.server.logging|_ThreadID=53;_ThreadName=Thread-2;|java.lang.NullPointerException: WriteText method cannot write null text at org.icefaces.impl.context.DOMResponseWriter.writeText(DOMResponseWriter.java:314) at org.icefaces.impl.context.DOMResponseWriter.writeText(DOMResponseWriter.java:340) at com.sun.faces.renderkit.html_basic.OutputMessageRenderer.encodeEnd(OutputMessageRenderer.java:163) at javax.faces.component.UIComponentBase.encodeEnd(UIComponentBase.java:875) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1764) at javax.faces.render.Renderer.encodeChildren(Renderer.java:168) at org.icefaces.impl.renderkit.RendererWrapper.encodeChildren(RendererWrapper.java:49) at javax.faces.component.UIComponentBase.encodeChildren(UIComponentBase.java:845) at com.sun.faces.renderkit.html_basic.HtmlBasicRenderer.encodeRecursive(HtmlBasicRenderer.java:304) at com.sun.faces.renderkit.html_basic.GroupRenderer.encodeChildren(GroupRenderer.java:105) at javax.faces.component.UIComponentBase.encodeChildren(UIComponentBase.java:845) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1757) at javax.faces.render.Renderer.encodeChildren(Renderer.java:168) at org.icefaces.impl.renderkit.RendererWrapper.encodeChildren(RendererWrapper.java:49) at javax.faces.component.UIComponentBase.encodeChildren(UIComponentBase.java:845) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1757) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1760) at org.icefaces.impl.context.DOMPartialViewContext.processPartial(DOMPartialViewContext.java:142) at javax.faces.component.UIViewRoot.encodeChildren(UIViewRoot.java:981) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1757) at com.sun.faces.application.view.FaceletViewHandlingStrategy.renderView(FaceletViewHandlingStrategy.java:391) at com.sun.faces.application.view.MultiViewHandler.renderView(MultiViewHandler.java:131) at javax.faces.application.ViewHandlerWrapper.renderView(ViewHandlerWrapper.java:288) at com.sun.faces.lifecycle.RenderResponsePhase.execute(RenderResponsePhase.java:121) at com.sun.faces.lifecycle.Phase.doPhase(Phase.java:101) at com.sun.faces.lifecycle.LifecycleImpl.render(LifecycleImpl.java:139) at javax.faces.webapp.FacesServlet.service(FacesServlet.java:594) at org.apache.catalina.core.StandardWrapper.service(StandardWrapper.java:1542) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:281) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:175) at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:655) at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:595) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:161) at org.apache.catalina.connector.CoyoteAdapter.doService(CoyoteAdapter.java:331) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:231) at com.sun.enterprise.v3.services.impl.ContainerMapper$AdapterCallable.call(ContainerMapper.java:317) at com.sun.enterprise.v3.services.impl.ContainerMapper.service(ContainerMapper.java:195) at com.sun.grizzly.http.ProcessorTask.invokeAdapter(ProcessorTask.java:849) at com.sun.grizzly.http.ProcessorTask.doProcess(ProcessorTask.java:746) at com.sun.grizzly.http.ProcessorTask.process(ProcessorTask.java:1045) at com.sun.grizzly.http.DefaultProtocolFilter.execute(DefaultProtocolFilter.java:228) at com.sun.grizzly.DefaultProtocolChain.executeProtocolFilter(DefaultProtocolChain.java:137) at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:104) at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:90) at com.sun.grizzly.http.HttpProtocolChain.execute(HttpProtocolChain.java:79) at com.sun.grizzly.ProtocolChainContextTask.doCall(ProtocolChainContextTask.java:54) at com.sun.grizzly.SelectionKeyContextTask.call(SelectionKeyContextTask.java:59) at com.sun.grizzly.ContextTask.run(ContextTask.java:71) at com.sun.grizzly.util.AbstractThreadPool$Worker.doWork(AbstractThreadPool.java:532) at com.sun.grizzly.util.AbstractThreadPool$Worker.run(AbstractThreadPool.java:513) at java.lang.Thread.run(Thread.java:722) |#]

  Read the article

• Play 2.0 javaToDo tutorial doesn't compile

  - by chsn

  I'm trying to follow the Play2.0 JavaToDO tutorial and for some reason it just doesn't want to work. Have looked through stackoverflow and other online resources, but haven't find an answer to this and it's driving me crazy. Attached code of the Application.java package controllers; import models.Task; import play.data.Form; import play.mvc.Controller; import play.mvc.Result; public class Application extends Controller { static Form<Task> taskForm = form(Task.class); public static Result index() { return redirect(routes.Application.tasks()); } public static Result tasks() { return ok( views.html.index.render(Task.all(), taskForm)); } public static Result newTask() { return TODO; } public static Result deleteTask(Long id) { return TODO; } } Attached code of the Task java package models; import java.util.List; import javax.persistence.Entity; import play.data.Form; import play.data.validation.Constraints.Required; import play.db.ebean.Model.Finder; import play.mvc.Result; import controllers.routes; @Entity public class Task { public Long id; @Required public String label; // search public static Finder<Long,Task> find = new Finder( Long.class, Task.class); // display tasks public static List<Task> all() { return find.all(); } // create task public static void create(Task task) { task.create(task); } // delete task public static void delete(Long id) { find.ref(id).delete(id); // find.ref(id).delete(); } // create new task public static Result newTask() { Form<Task> filledForm = taskForm.bindFromRequest(); if(filledForm.hasErrors()) { return badRequest( views.html.index.render(Task.all(), filledForm) ); } else { Task.create(filledForm.get()); return redirect(routes.Application.tasks()); } } } I get a compile error on Task.java on the line static Form<Task> taskForm = form(Task.class); As I'm working on eclipse (the project is eclipsified before import), it's telling me that taskForm cannot be resolved and it also underlines every play 2 command e.g. "render(), redirect(), bindFromRequest()" asking me to create a method for it. Any ideas how to solve the compilations error and also how to get Eclipse to recognize the play2 commands? EDIT: updated Application.java package controllers; import models.Task; import play.data.Form; import play.mvc.Controller; import play.mvc.Result; public class Application extends Controller { // create new task public static Result newTask() { Form<Task> filledForm = form(Task.class).bindFromRequest(); if(filledForm.hasErrors()) { return badRequest( views.html.index.render(Task.all(), filledForm) ); } else { Task.newTask(filledForm.get()); return redirect(routes.Application.tasks()); } } public static Result index() { return redirect(routes.Application.tasks()); } public static Result tasks() { return ok( views.html.index.render(Task.all(), taskForm)); } public static Result deleteTask(Long id) { return TODO; } } Updated task.java package models; import java.util.List; import javax.persistence.Entity; import play.data.Form; import play.data.validation.Constraints.Required; import play.db.ebean.Model; import play.db.ebean.Model.Finder; import play.mvc.Result; import controllers.routes; @Entity public class Task extends Model { public Long id; @Required public String label; // Define a taskForm static Form<Task> taskForm = form(Task.class); // search public static Finder<Long,Task> find = new Finder( Long.class, Task.class); // display tasks public static List<Task> all() { return find.all(); } // create new task public static Result newTask(Task newTask) { save(task); } // delete task public static void delete(Long id) { find.ref(id).delete(id); // find.ref(id).delete(); } }

  Read the article

• SQLAuthority News – Public Training Classes In Hyderabad 12-14 May – Microsoft SQL Server 2005/2008

  - by pinaldave

  After successfully delivering many corporate trainings as well as the private training Solid Quality Mentors, India is launching the Public Training in Hyderabad for SQL Server 2008 and SharePoint 2010. This is going to be one of the most unique and one-of-a-kind events in India where Solid Quality Mentors are offering public classes. I will be leading the training on Microsoft SQL Server 2005/2008 Query Optimization & Performance Tuning. This intensive, 3-day course intends to give attendees an in-depth look at Query Optimization and Performance Tuning in SQL Server 2005 and 2008. Designed to prepare SQL Server developers and administrators for a transition into SQL Server 2005 or 2008, the course covers the best practices for a variety of essential tasks in order to maximize the performance. At the end of the course, there would be daily discussions about your real-world problems and find appropriate solutions. Note: Scroll down for course fees, discount, dates and location. Do not forget to take advantage of Discount code ‘SQLAuthority‘. The training premises are very well-equipped as they will be having 1:1 computers. Every participant will be provided with printed course materials. I will pick up your entire lunch tab and we will have lots of SQL talk together. The best participant will receive a special gift at the end of the course. Even though the quality of the material to be delivered together with the course will be of extremely high standard, the course fees are set at a very moderate rate. The fee for the course is INR 14,000/person for the whole 3-day convention. At the rate of 1 USD = 44 INR, this fee converts to less than USD 300. At this rate, it is totally possible to fly from anywhere from the world to India and take the training and still save handsome pocket money. It would be even better if you register using the discount code “SQLAuthority“, for you will instantly get an INR 3000 discount, reducing the total cost of the training to INR 11,000/person for whole 3 days course. This is a onetime offer and will not be available in the future. Please note that there will be a 10.3% service tax on course fees. To register, either send an email to [email protected] or call +91 95940 43399. Feel free to drop me an email at [email protected] for any additional information and clarification. Training Date and Time: May 12-14, 2010 10 AM- 6 PM. Training Venue: Abridge Solutions, #90/B/C/3/1, Ganesh GHR & MSY Plaza, Vittalrao Nagar, Near Image Hospital, Madhapur, Hyderabad – 500 081. The details of the course is as listed below. Day 1 : Strengthen the basics along with SQL Server 2005/2008 New Features Module 01: Subqueries, Ranking Functions, Joins and Set Operations Module 02: Table Expressions Module 03: TOP and APPLY Module 04: SQL Server 2008 Enhancements Day 2: Query Optimization & Performance Tuning 1 Module 05: Logical Query Processing Module 06: Query Tuning Module 07:  Introduction to the Query Processor Module 08:  Review of common query coding which causes poor performance Day 3: Query Optimization & Performance Tuning 2 Module 09:  SQL Server Indexing and index maintenance Module 10:  Plan Guides, query hints, UDFs, and Computed Columns Module 11:  Understanding SQL Server Execution Plans Module 12: Real World Index and Optimization Tips Download the complete PDF brochure. We are also going to have SharePoint 2010 training by Joy Rathnayake on 10-11 May. All the details for discount applies to the same as well. Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Training, SQLAuthority News, T SQL, Technology

  Read the article

• Unable to either locate any wireless networks nor even connect to wifi

  - by Leo Chan

  I'm new to Linux. I currently have installed ubuntu 12.10. I had a previous problem with my wireless card (see url to see previous problem : How to enable wireless in a Fujitsu LH532?). It now shows Connect to hidden network and create new wireless network but now unfortunately it simply cannot find any wireless connections. I did have a very thorough look around about this problem such as wait a little longer since sometimes it cannot load all the wireless connections available that quickly. My wifi is a hidden network and I have used the connect to hidden network feature but it keeps asking for my wep key which has been checked 4 times (I counted) and it still seems to not work; It keeps asking for the WEP key. I did try both WEP 40/128-bit key and WPA & WPA2 since previously on my windows it worked; My family later decided to use WEP. I only have a quick fix using a usb wireless stick and I wish to have a more solid fix. Thanks Results from sudo iwlist wlan0 scan wlan0 Scan completed : Cell 01 - Address: 00:1E:73:C8:62:BD Channel:6 Frequency:2.437 GHz (Channel 6) Quality=25/70 Signal level=-85 dBm Encryption key:on ESSID:"EnigmaHome" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000cb3bb10a5c Extra: Last beacon: 696ms ago IE: Unknown: 000A456E69676D61486F6D65 IE: Unknown: 010482848B96 IE: Unknown: 030106 IE: Unknown: 0706484B20010B1E IE: Unknown: 2A0107 IE: Unknown: 32080C1218243048606C IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 Cell 02 - Address: C8:3A:35:34:C1:60 Channel:6 Frequency:2.437 GHz (Channel 6) Quality=22/70 Signal level=-88 dBm Encryption key:on ESSID:"Tenda" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s Mode:Master Extra:tsf=000001336e70ffdd Extra: Last beacon: 716ms ago IE: Unknown: 000554656E6461 IE: Unknown: 010882848B961224486C IE: Unknown: 030106 IE: Unknown: 32040C183060 IE: Unknown: 0706434E20010D10 IE: Unknown: 33082001020304050607 IE: Unknown: 33082105060708090A0B IE: Unknown: DD270050F204104A0001101044000101104700102880288028801880A880C83A3534C160103C000101 IE: Unknown: 050400010000 IE: Unknown: 2A0106 IE: Unknown: 2D1AEC0117FFFF0000000000000000000000000000000C0000000000 IE: Unknown: 3D1606000500000000000000000000000000000000000000 IE: Unknown: 7F0101 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Preauthentication Supported IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 IE: Unknown: 0B05010089127A IE: Unknown: DD1E00904C33EC0117FFFF0000000000000000000000000000000C0000000000 IE: Unknown: DD1A00904C3406000500000000000000000000000000000000000000 IE: Unknown: DD07000C4304000000 Cell 03 - Address: 00:1E:73:C8:62:BF Channel:6 Frequency:2.437 GHz (Channel 6) Quality=47/70 Signal level=-63 dBm Encryption key:on ESSID:"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000cb3bac614e Extra: Last beacon: 1064ms ago IE: Unknown: 00110000000000000000000000000000000000 IE: Unknown: 010482848B96 IE: Unknown: 030106 IE: Unknown: 050C010200000000000000000000 IE: Unknown: 0706484B20010B1E IE: Unknown: 2A0107 IE: Unknown: 32080C1218243048606C IE: Unknown: DD070050F202000100

  Read the article

• A Forming Repository of Script Samples for Automating Windows Server 2012 and Windows 8

  - by Jialiang

  Compared with Windows Server 2008/R2 that provides about 230 cmdlets, Windows Server 2012 beats that by a factor of over 10 shipping ~ 2,430 cmdlets.  You can automate almost every aspect of the server.   The new PowerShell 3.0, like Windows Server 2012, has a ton of new features.  In this automation script-centric move, Microsoft All-In-One Script Framework (AIOSF) is ready to support IT Pros with many new services and offerings coming this year.  We sincerely hope that the IT community will benefit from the effort. Here is the first one among our new services and offerings:  The team is preparing a large set of Windows 8 / Windows Server 2012 script samples based on frequently asked IT tasks that we collect in TechNet forums and support calls to Microsoft.   Because the script topics come from frequently asked IT tasks, we hope that these script samples can be helpful to many IT Pros worldwide.   With the General Availability of Windows Server 2012, we release the first three Windows Server 2012 / Windows 8 script samples today.    Get Network Adapter Properties in Windows Server 2012 and Windows 8 (PowerShell) http://gallery.technet.microsoft.com/scriptcenter/Get-Network-Adapter-37c5a913 Description: This script could be used to get network adapter properties and advanced properties in Windows Server 2012 and Windows 8. It combines the outputs of Get-NetAdapter and Get-NetAdapterAdvancedProperty. It can generate a report of network adapter configuration settings. Use Scenarios: In a real world, IT Administrators are required to check the configuration of network adapters after the deployment of new servers. One typical example is the duplex setting of network adapters. Also, IT administrators need to maintain a server list which contains network adapter configuration settings in a regular basis. Before Windows Server 2012, IT administrators often feel difficulties to handle these tasks. Acknowledgement: Thanks Greg Gu from AIOSF for collecting this script topic, and writing the script sample.  Thanks James Adams (Microsoft Premier Field Engineer) for reviewing the script sample and ensuring its quality.   How to batch create virtual machines in Windows Server 2012 (PowerShell) http://gallery.technet.microsoft.com/scriptcenter/How-to-batch-create-9efd1811 Description: This PowerShell Script illustrates how to batch create multiple virtual machines based on comma delimited file by using PowerShell 3.0 in Windows Server 2012. Use Scenarios: IT admin requires to batch creating virtual machines in Windows Server 2012, although they can use few commands due to the lack of programming knowledge. Although it’s a set of Hyper-V command-lets within Windows PowerShell, IT Admins are reluctant to use them except simple a command which is widely used. Acknowledgement: Thanks Anders Wang from AIOSF for collecting this script topic and writing the script sample.  Thanks Christopher Norris for reviewing the script sample and ensuring its quality before publishing.   Remove Windows Store Apps in Windows 8 (PowerShell) http://gallery.technet.microsoft.com/scriptcenter/Remove-Windows-Store-Apps-a00ef4a4 Description: This script can be used to remove multiple Windows Store Apps from a user account in Windows 8. It provides a list of installed Windows Store applications. You can specify the application IDs, and remove them all at once. Use Scenarios: 1. In Windows 8, you can remove a single Windows Store App by right-clicking the tile in the Start menu and choosing the uninstall command.  However, no command is provided for removing multiple Windows Store Apps all at once. If you want to do so, you can use this script sample. 2. Sometimes Windows Store Apps may crash in Windows 8.  Even though you can successfully uninstall and reinstall the App, the application may still crash after the reinstallation.  In this situation, you can use this example script to remove these Windows Store Apps cleanly. Acknowledgement: Thanks Edward Qi from AIOSF for collecting the script idea and composing the script sample.  Thanks James Adams (Microsoft Premier Field Engineer) for reviewing the script sample and ensuring its quality.   This is just the beginning, and more and more script samples are coming.  You can follow our blog (http://blogs.technet.com/b/onescript) to get the latest customer-driven script samples for Windows Server 2012 and Windows 8.

  Read the article

• Tile engine Texture not updating when numbers in array change

  - by Corey

  I draw my map from a txt file. I am using java with slick2d library. When I print the array the number changes in the array, but the texture doesn't change. public class Tiles { public Image[] tiles = new Image[5]; public int[][] map = new int[64][64]; public Image grass, dirt, fence, mound; private SpriteSheet tileSheet; public int tileWidth = 32; public int tileHeight = 32; public void init() throws IOException, SlickException { tileSheet = new SpriteSheet("assets/tiles.png", tileWidth, tileHeight); grass = tileSheet.getSprite(0, 0); dirt = tileSheet.getSprite(7, 7); fence = tileSheet.getSprite(2, 0); mound = tileSheet.getSprite(2, 6); tiles[0] = grass; tiles[1] = dirt; tiles[2] = fence; tiles[3] = mound; int x=0, y=0; BufferedReader in = new BufferedReader(new FileReader("assets/map.dat")); String line; while ((line = in.readLine()) != null) { String[] values = line.split(","); x = 0; for (String str : values) { int str_int = Integer.parseInt(str); map[x][y]=str_int; //System.out.print(map[x][y] + " "); x++; } //System.out.println(""); y++; } in.close(); } public void update(GameContainer gc) { } public void render(GameContainer gc) { for(int y = 0; y < map.length; y++) { for(int x = 0; x < map[0].length; x ++) { int textureIndex = map[x][y]; Image texture = tiles[textureIndex]; texture.draw(x*tileWidth,y*tileHeight); } } } } Mouse Picking Where I change the number in the array Input input = gc.getInput(); gc.getInput().setOffset(cameraX-400, cameraY-300); float mouseX = input.getMouseX(); float mouseY = input.getMouseY(); double mousetileX = Math.floor((double)mouseX/tiles.tileWidth); double mousetileY = Math.floor((double)mouseY/tiles.tileHeight); double playertileX = Math.floor(playerX/tiles.tileWidth); double playertileY = Math.floor(playerY/tiles.tileHeight); double lengthX = Math.abs((float)playertileX - mousetileX); double lengthY = Math.abs((float)playertileY - mousetileY); double distance = Math.sqrt((lengthX*lengthX)+(lengthY*lengthY)); if(input.isMousePressed(Input.MOUSE_LEFT_BUTTON) && distance < 4) { System.out.println("Clicked"); if(tiles.map[(int)mousetileX][(int)mousetileY] == 1) { tiles.map[(int)mousetileX][(int)mousetileY] = 0; } } I never ask a question until I have tried to figure it out myself. I have been stuck with this problem for two weeks. It's not like this site is made for asking questions or anything. So if you actually try to help me instead of telling me to use a debugger thank you. You either get told you have too much or too little code. Nothing is never enough for the people on here it's as bad as something like reddit. Idk what is wrong all my textures work when I render them it just doesn't update when the number in the array changes. I am obviously debugging when I say that I was printing the array and the number is changing like it should, so it's not a problem with my mouse picking code. It is a problem with my textures, but I don't know what because they all render correctly. That is why I need help.

  Read the article

• All libGDX input statements are returning TRUE at once

  - by MowDownJoe

  I'm fooling around with Box2D and libGDX and running into a peculiar problem with polling for input. Here's the code for the Screen's render() loop: @Override public void render(float delta) { Gdx.gl20.glClearColor(0, 0, .2f, 1); Gdx.gl20.glClear(GL20.GL_COLOR_BUFFER_BIT); camera.update(); game.batch.setProjectionMatrix(camera.combined); debugRenderer.render(world, camera.combined); if(Gdx.input.isButtonPressed(Keys.LEFT)){ Gdx.app.log("Input", "Left is being pressed."); pushyThingyBody.applyForceToCenter(-10f, 0); } if(Gdx.input.isButtonPressed(Keys.RIGHT)){ Gdx.app.log("Input", "Right is being pressed."); pushyThingyBody.applyForceToCenter(10f, 0); } world.step((1f/45f), 6, 2); } And the constructor is largely just setting up the World, Box2DDebugRenderer, and all the Bodies in the world: public SandBox(PhysicsSandboxGame game) { this.game = game; camera = new OrthographicCamera(800, 480); camera.setToOrtho(false); world = new World(new Vector2(0, -9.8f), true); debugRenderer = new Box2DDebugRenderer(); BodyDef bodyDef = new BodyDef(); bodyDef.type = BodyType.DynamicBody; bodyDef.position.set(100, 300); body = world.createBody(bodyDef); CircleShape circle = new CircleShape(); circle.setRadius(6f); FixtureDef fixtureDef = new FixtureDef(); fixtureDef.shape = circle; fixtureDef.density = .5f; fixtureDef.friction = .4f; fixtureDef.restitution = .6f; fixture = body.createFixture(fixtureDef); circle.dispose(); BodyDef groundBodyDef = new BodyDef(); groundBodyDef.position.set(new Vector2(0, 10)); groundBody = world.createBody(groundBodyDef); PolygonShape groundBox = new PolygonShape(); groundBox.setAsBox(camera.viewportWidth, 10f); groundBody.createFixture(groundBox, 0f); groundBox.dispose(); BodyDef pushyThingyBodyDef = new BodyDef(); pushyThingyBodyDef.type = BodyType.DynamicBody; pushyThingyBodyDef.position.set(new Vector2(400, 30)); pushyThingyBody = world.createBody(pushyThingyBodyDef); PolygonShape pushyThingyShape = new PolygonShape(); pushyThingyShape.setAsBox(40f, 10f); FixtureDef pushyThingyFixtureDef = new FixtureDef(); pushyThingyFixtureDef.shape = pushyThingyShape; pushyThingyFixtureDef.density = .4f; pushyThingyFixtureDef.friction = .1f; pushyThingyFixtureDef.restitution = .5f; pushyFixture = pushyThingyBody.createFixture(pushyThingyFixtureDef); pushyThingyShape.dispose(); } Testing this on the desktop. Basically, whenever I hit the appropriate keys, neither of the if statements in the loop return true. However, when I click in the window, both statements return true, resulting in a 0 net force on the body. Why is this?

  Read the article

• Oracle MDM Maturity Model

  - by David Butler

  A few weeks ago, I discussed the results of a survey conducted by Oracle’s Insight team. The survey was based on the data management maturity model that the Oracle Insight team has developed over the years as they analyzed customer IT organizations to help them get more out of everything they already have. I thought you might like to learn more about the maturity model itself. It can help you figure out where you stand when it comes to getting your organizations data management act together. The model covers maturity levels around five key areas: Profiling data sources; Defining a data strategy; Defining a data consolidation plan; Data maintenance; and Data utilization. Profile data sources: Profiling data sources involves taking an inventory of all data sources from across your IT landscape. Then evaluate the quality of the data in each source system. This enables the scoping of what data to collect into an MDM hub and what rules are needed to insure data harmonization across systems. Define data strategy: A data strategy requires an understanding of the data usage. Given data usage, various data governance requirements need to be developed. This includes data controls and security rules as well as data structure and usage policies. Define data consolidation strategy: Consolidation requires defining your operational data model. How integration is to be accomplished. Cross referencing common data attributes from multiple systems is needed. Synchronization policies also need to be developed. Data maintenance: The desired standardization needs to be defined, including what constitutes a ‘match’ once the data has been standardized. Cleansing rules are a part of this methodology. Data quality monitoring requirements also need to be defined. Utilize the data: What data gets published, and who consumes the data must be determined. How to get the right data to the right place in the right format given its intended use must be understood. Validating the data and insuring security rules are in place and enforced are crucial aspects for full no-risk data utilization. For each of the above data management areas, a maturity level needs to be assessed. Where your organization wants to be should also be identified using the same maturity levels. This results in a sound gap analysis your organization can use to create action plans to achieve the ultimate goals. Marginal is the lowest level. It is characterized by manually maintaining trusted sources; lacking or inconsistent, silo’d structures with limited integration, and gaps in automation. Stable is the next leg up the MDM maturity staircase. It is characterized by tactical MDM implementations that are limited in scope and target a specific division.  It includes limited data stewardship capabilities as well. Best Practice is a serious MDM maturity level characterized by process automation improvements. The scope is enterprise wide. It is a business solution that provides a single version of the truth, with closed-loop data quality capabilities. It is typically driven by an enterprise architecture group with both business and IT representation.   Transformational is the highest MDM maturity level. At this level, MDM is quantitatively managed. It is integrated with Business Intelligence, SOA, and BPM. MDM is leveraged in business process orchestration. Take an inventory using this MDM Maturity Model and see where you are in your journey to full MDM maturity with all the business benefits that accrue to organizations who have mastered their data for the benefit of all operational applications, business processes, and analytical systems. To learn more, Trevor Naidoo and I have written the Oracle MDM Maturity Model whitepaper. It’s free, so go ahead and download it and use it as you see fit.

  Read the article

• How does interpolation actually work to smooth out an object's movement?

  - by user22241

  I've asked a few similar questions over the past 8 months or so with no real joy, so I am going make the question more general. I have an Android game which is OpenGL ES 2.0. within it I have the following Game Loop: My loop works on a fixed time step principle (dt = 1 / ticksPerSecond) loops=0; while(System.currentTimeMillis() > nextGameTick && loops < maxFrameskip){ updateLogic(dt); nextGameTick+=skipTicks; timeCorrection += (1000d/ticksPerSecond) % 1; nextGameTick+=timeCorrection; timeCorrection %=1; loops++; } render(); My intergration works like this: sprite.posX+=sprite.xVel*dt; sprite.posXDrawAt=sprite.posX*width; Now, everything works pretty much as I would like. I can specify that I would like an object to move across a certain distance (screen width say) in 2.5 seconds and it will do just that. Also because of the frame skipping that I allow in my game loop, I can do this on pretty much any device and it will always take 2.5 seconds. Problem However, the problem is that when a render frame skips, the graphic stutter. It's extremely annoying. If I remove the ability to skip frames, then everything is smooth as you like, but will run at different speeds on different devices. So it's not an option. I'm still not sure why the frame skips, but I would like to point out that this is Nothing to do with poor performance, I've taken the code right back to 1 tiny sprite and no logic (apart from the logic required to move the sprite) and I still get skipped frames. And this is on a Google Nexus 10 tablet (and as mentioned above, I need frame skipping to keep the speed consistent across devices anyway). So, the only other option I have is to use interpolation (or extrapolation), I've read every article there is out there but none have really helped me to understand how it works and all of my attempted implementations have failed. Using one method I was able to get things moving smoothly but it was unworkable because it messed up my collision. I can foresee the same issue with any similar method because the interpolation is passed to (and acted upon within) the rendering method - at render time. So if Collision corrects position (character now standing right next to wall), then the renderer can alter it's position and draw it in the wall. So I'm really confused. People have said that you should never alter an object's position from within the rendering method, but all of the examples online show this. So I'm asking for a push in the right direction, please do not link to the popular game loop articles (deWitters, Fix your timestep, etc) as I've read these multiple times. I'm not asking anyone to write my code for me. Just explain please in simple terms how Interpolation actually works with some examples. I will then go and try to integrate any ideas into my code and will ask more specific questions if need-be further down the line. (I'm sure this is a problem many people struggle with).

  Read the article

• Slick2D Rendering Lots of Polygons

  - by Hazzard

  I'm writing an little isometric game using Slick. The world terrain is made up of lots of quadrilaterals. In a small world that is 128 by 128 squares, over 16,000 quadrilaterals need to be rendered. This puts my pretty powerful computer down to 30 fps. I've though about caching "chunks" of the world so only single chunks would ever need updating at a time, but I don't know how to do this, and I am sure there are other ways to optimize it besides that. Maybe I'm doing the whole thing wrong, surely fancy 3D games that run fine on my machine are more intensive than this. My question is how can I improve the FPS and am I doing something wrong? Or does it actually take that much power to render those polygons? -- Here is the source code for the render method in my game state. It iterates through a 2d array or heights and draws polygons based on the height. public void render(GameContainer container, StateBasedGame game, Graphics gfx) throws SlickException { gfx.translate(offsetX * d + container.getWidth() / 2, offsetY * d + container.getHeight() / 2); gfx.scale(d, d); for (int y = 0; y < placeholder.length; y++) {// x & y are isometric // diag for (int x = 0; x < placeholder[0].length; x++) { Polygon poly; int hor = TestState.TILE_WIDTH * (x - y);// hor and ver are orthagonal int W = TestState.TILE_HEIGHT * (x + y) - 1 * heights[y + 1][x];//points to go off of int S = TestState.TILE_HEIGHT * (x + y) - 1 * heights[y + 1][x + 1]; int E = TestState.TILE_HEIGHT * (x + y) - 1 * heights[y][x + 1]; int N = TestState.TILE_HEIGHT * (x + y) - 1 * heights[y][x]; if (placeholder[y][x] == null) { poly = new Polygon();//Create actual surface polygon poly.addPoint(-TestState.TILE_WIDTH + hor, W); poly.addPoint(hor, S + TestState.TILE_HEIGHT); poly.addPoint(TestState.TILE_WIDTH + hor, E); poly.addPoint(hor, N - TestState.TILE_HEIGHT); float z = ((float) heights[y][x + 1] - heights[y + 1][x]) / 32 + 0.5f; placeholder[y][x] = new Tile(poly, new Color(z, z, z)); //ShapeRenderer.fill(placeholder[y][x]); } if (true) {//ONLY draw tile if it's on screen gfx.setColor(placeholder[y][x].getColor()); ShapeRenderer.fill(placeholder[y][x]); //gfx.fill(placeholder[y][x]); //placeholder[y][x]. //DRAW EDGES if (y + 1 == placeholder.length) {//draw South foundation edges gfx.setColor(Color.gray); Polygon found = new Polygon(); found.addPoint(-TestState.TILE_WIDTH + hor, W); found.addPoint(hor, S + TestState.TILE_HEIGHT); found.addPoint(hor, TestState.TILE_HEIGHT * (x + y + 1)); found.addPoint(-TestState.TILE_WIDTH + hor, TestState.TILE_HEIGHT * (x + y)); gfx.fill(found); } if (x + 1 == placeholder[0].length) {//north gfx.setColor(Color.darkGray); Polygon found = new Polygon(); found.addPoint(TestState.TILE_WIDTH + hor, E); found.addPoint(hor, S + TestState.TILE_HEIGHT); found.addPoint(hor, TestState.TILE_HEIGHT * (x + y + 1)); found.addPoint(TestState.TILE_WIDTH + hor, TestState.TILE_HEIGHT * (x + y)); gfx.fill(found); }//*/ } } } }

  Read the article

• How do I cap rendering of tiles in a 2D game with SDL?

  - by farmdve

  I have some boilerplate code working, I basically have a tile based map composed of just 3 colors, and some walls and render with SDL. The tiles are in a bmp file, but each tile inside it corresponds to an internal number of the type of tile(color, or wall). I have pretty basic collision detection and it works, I can also detetc continuous presses, which allows me to move pretty much anywhere I want. I also have a moving camera, which follows the object. The problem is that, the tile based map is bigger than the resolution, thus not all of the map can be displayed on the screen, but it's still rendered. I would like to cap it, but since this is new to me, I pretty much have no idea. Although I cannot post all the code, as even though I am a newbie and the code pretty basic, it's already quite a few lines, I can post what I tried to do void set_camera() { //Center the camera over the dot camera.x = ( player.box.x + DOT_WIDTH / 2 ) - SCREEN_WIDTH / 2; camera.y = ( player.box.y + DOT_HEIGHT / 2 ) - SCREEN_HEIGHT / 2; //Keep the camera in bounds. if(camera.x < 0 ) { camera.x = 0; } if(camera.y < 0 ) { camera.y = 0; } if(camera.x > LEVEL_WIDTH - camera.w ) { camera.x = LEVEL_WIDTH - camera.w; } if(camera.y > LEVEL_HEIGHT - camera.h ) { camera.y = LEVEL_HEIGHT - camera.h; } } set_camera() is the function which calculates the camera position based on the player's positions. I won't pretend I know much about it. Rectangle box = {0,0,0,0}; for(int t = 0; t < TOTAL_TILES; t++) { if(box.x < (camera.x - TILE_WIDTH) || box.y > (camera.y - TILE_HEIGHT)) apply_surface(box.x - camera.x, box.y - camera.y, surface, screen, &clips[tiles[t]]); box.x += TILE_WIDTH; //If we've gone too far if(box.x >= LEVEL_WIDTH) { //Move back box.x = 0; //Move to the next row box.y += TILE_HEIGHT; } } This is basically my render code. The for loop loops over 192 tiles stored in an int array, each with their own unique value describing the tile type(wall or one of three possible colored tiles). box is an SDL_Rect containing the current position of the tile, which is calculated on render. TILE_HEIGHT and TILE_WIDTH are of value 80. So the cap is determined by if(box.x < (camera.x - TILE_WIDTH) || box.y > (camera.y - TILE_HEIGHT)) However, this is just me playing with the values and see what doesn't break it. I pretty much have no idea how to calculate it. My screen resolution is 1024/768, and the tile map is of size 1280/960.

  Read the article

• Extrapolation breaks collision detection

  - by user22241

  Before applying extrapolation to my sprite's movement, my collision worked perfectly. However, after applying extrapolation to my sprite's movement (to smooth things out), the collision no longer works. This is how things worked before extrapolation: However, after I implement my extrapolation, the collision routine breaks. I am assuming this is because it is acting upon the new coordinate that has been produced by the extrapolation routine (which is situated in my render call ). After I apply my extrapolation How to correct this behaviour? I've tried puting an extra collision check just after extrapolation - this does seem to clear up a lot of the problems but I've ruled this out because putting logic into my rendering is out of the question. I've also tried making a copy of the spritesX position, extrapolating that and drawing using that rather than the original, thus leaving the original intact for the logic to pick up on - this seems a better option, but it still produces some weird effects when colliding with walls. I'm pretty sure this also isn't the correct way to deal with this. I've found a couple of similar questions on here but the answers haven't helped me. This is my extrapolation code: public void onDrawFrame(GL10 gl) { //Set/Re-set loop back to 0 to start counting again loops=0; while(System.currentTimeMillis() > nextGameTick && loops < maxFrameskip){ SceneManager.getInstance().getCurrentScene().updateLogic(); nextGameTick+=skipTicks; timeCorrection += (1000d/ticksPerSecond) % 1; nextGameTick+=timeCorrection; timeCorrection %=1; loops++; tics++; } extrapolation = (float)(System.currentTimeMillis() + skipTicks - nextGameTick) / (float)skipTicks; render(extrapolation); } Applying extrapolation render(float extrapolation){ //This example shows extrapolation for X axis only. Y position (spriteScreenY is assumed to be valid) extrapolatedPosX = spriteGridX+(SpriteXVelocity*dt)*extrapolation; spriteScreenPosX = extrapolationPosX * screenWidth; drawSprite(spriteScreenX, spriteScreenY); } Edit As I mentioned above, I have tried making a copy of the sprite's coordinates specifically to draw with.... this has it's own problems. Firstly, regardless of the copying, when the sprite is moving, it's super-smooth, when it stops, it's wobbling slightly left/right - as it's still extrapolating it's position based on the time. Is this normal behavior and can we 'turn it off' when the sprite stops? I've tried having flags for left / right and only extrapolating if either of these is enabled. I've also tried copying the last and current positions to see if there is any difference. However, as far as collision goes, these don't help. If the user is pressing say, the right button and the sprite is moving right, when it hits a wall, if the user continues to hold the right button down, the sprite will keep animating to the right, while being stopped by the wall (therefore not actually moving), however because the right flag is still set and also because the collision routine is constantly moving the sprite out of the wall, it still appear to the code (not the player) that the sprite is still moving, and therefore extrapolation continues. So what the player would see, is the sprite 'static' (yes, it's animating, but it's not actually moving across the screen), and every now and then it shakes violently as the extrapolation attempts to do it's thing....... Hope this help

  Read the article

• WinForms ReportViewer: slow initial rendering

  - by Bryan Roth

  UPDATE 2.4.2010 Yeah, this is an old question but I thought I would give an update. So, I'm working with the ReportViewer again and it's still rendering slowly on the initial load. The only difference is that the SQL database is on the reporting server. UPDATE 3.16.2009 I have done profiling and it's not the SQL that is making the ReportViewer render slowly on the first call. On the first call, the ReportViewer control locks up the UI thread and makes the program unresponsive. After about 5 seconds the ReportViewer will unlock the UI thread and display "Report is being generated" and then finally show the report. I know 5 seconds is not much but this shouldn't be happening. My coworker does the same thing in a program of his and the ReportViewer immediately displays the "Report is being generated" upon any request. The only difference is that the reporting server is on one server and the data is on another server. However, when I am developing the reports within SSRS, there is no delay. UPDATE I have noticed that only the first load of the ReportViewer takes a long time; each subsequent load of the same or different reports loads fast. I have a WinForms ReportViewer that I'm using in Remote processing mode that can take up to 30 seconds to render when the ReportViewer.RefreshReport() method is called. However, the report itself runs fast. This is the code to setup my ReportViewer: rvReport.ProcessingMode = ProcessingMode.Remote rvReport.ShowParameterPrompts = False rvReport.ServerReport.ReportServerUrl = New Uri(_reportServerURL) rvReport.ServerReport.ReportPath = _reportPath This is where the ReportViewer can take up to 30 seconds to render: rvReport.RefreshReport()

  Read the article

• WPF 3.5 RenderTargetBitmap memory hog

  - by kingRauk

  I have a 3.5 WPF application that use's RenderTargetBitmap. It eat's memory like a big bear. It's is a know problem in 3.5 that RenderTargetBitmap.Render has memory problems. Have find some solutions for it, but i doesnt help. https://connect.microsoft.com/VisualStudio/feedback/details/489723/rendertargetbitmap-render-method-causes-a-memory-leak Program takes too much memory And more... Does anyway have any more ideas to solve it... static Image Method(FrameworkElement e, int width, int height) { const int dpi = 192; e.Width = width; e.Height = height; e.Arrange(new Rect(0, 0, width, height)); e.UpdateLayout(); if(element is Graph) (element as Graph).UpdateComponents(); var bitmap = new RenderTargetBitmap((int)(width*dpi/96.0), (int)(height*dpi/96.0), dpi, dpi, PixelFormats.Pbgra32); bitmap.Render(element); var encoder = new PngBitmapEncoder(); encoder.Frames.Add(BitmapFrame.Create(bitmap)); using (var stream = new MemoryStream()) { encoder.Save(stream); element.Clip = null; Dispose(element); bitmap.Freeze(); DisposeRender(bitmap); bitmap.Clear(); GC.Collect(); GC.WaitForPendingFinalizers(); return System.Drawing.Image.FromStream(stream); } } public static void Dispose(FrameworkElement element) { GC.Collect(); GC.WaitForPendingFinalizers(); GC.Collect(); } public static void DisposeRender(RenderTargetBitmap bitmap) { if (bitmap != null) bitmap.Clear(); bitmap = null; GC.Collect(); GC.WaitForPendingFinalizers(); }

  Read the article

• Django Deploy trouble

  - by i-Malignus

  Well, i've walking around this for a couples of days now... I think is time to ask for some help, i think my installation is ok... Server OS: Centos 5 Python -v 2.6.5 Django -v (1, 1, 1, 'final', 0) my apache conf: <VirtualHost *:80> DocumentRoot /opt/workshop ServerName taller.antell.com.py WSGIScriptAlias / /opt/workshop/workshop.wsgi WSGIDaemonProcess taller.antell.com.py user=ignacio group=ignacio processes=2 threads=25 ErrorLog /opt/workshop/apache.error.log CustomLog /opt/workshop/apache.custom.log combined <Directory "/opt/workshop"> Options +ExecCGI +FollowSymLinks -Indexes -MultiViews AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> my mod_wsgi conf: import os import sys sys.path.append('/opt/workshop') os.environ['DJANGO_SETTINGS_MODULE'] = 'workshop.settings' os.environ['PYTHON_EGG_CACHE'] = '/tmp/.python-eggs' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler( ) the error that i'm getting on my apache error log is: [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] mod_wsgi (pid=11459): Exception occurred processing WSGI script '/opt/workshop/workshop.wsgi'. [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] Traceback (most recent call last): [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/handlers/wsgi.py", line 241, in __call__ [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] response = self.get_response(request) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/handlers/base.py", line 134, in get_response [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return self.handle_uncaught_exception(request, resolver, exc_info) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/handlers/base.py", line 154, in handle_uncaught_exception [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return debug.technical_500_response(request, *exc_info) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/views/debug.py", line 40, in technical_500_response [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] html = reporter.get_traceback_html() [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/views/debug.py", line 114, in get_traceback_html [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return t.render(c) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/template/__init__.py", line 178, in render [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return self.nodelist.render(context) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/template/__init__.py", line 779, in render [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] bits.append(self.render_node(node, context)) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/template/debug.py", line 81, in render_node [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] raise wrapped [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] TemplateSyntaxError: Caught an exception while rendering: No module named vehicles [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] Original Traceback (most recent call last): [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/template/debug.py", line 71, in render_node [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] result = node.render(context) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/template/debug.py", line 87, in render [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] output = force_unicode(self.filter_expression.resolve(context)) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/template/__init__.py", line 572, in resolve [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] new_obj = func(obj, *arg_vals) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/template/defaultfilters.py", line 687, in date [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return format(value, arg) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/dateformat.py", line 269, in format [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return df.format(format_string) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/dateformat.py", line 30, in format [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] pieces.append(force_unicode(getattr(self, piece)())) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/dateformat.py", line 175, in r [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return self.format('D, j M Y H:i:s O') [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/dateformat.py", line 30, in format [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] pieces.append(force_unicode(getattr(self, piece)())) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/encoding.py", line 71, in force_unicode [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] s = unicode(s) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/functional.py", line 201, in __unicode_cast [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return self.__func(*self.__args, **self.__kw) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/translation/__init__.py", line 62, in ugettext [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return real_ugettext(message) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/translation/trans_real.py", line 286, in ugettext [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return do_translate(message, 'ugettext') [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/translation/trans_real.py", line 276, in do_translate [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] _default = translation(settings.LANGUAGE_CODE) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/translation/trans_real.py", line 194, in translation [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] default_translation = _fetch(settings.LANGUAGE_CODE) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/translation/trans_real.py", line 180, in _fetch [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] app = import_module(appname) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/importlib.py", line 35, in import_module [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] __import__(name) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] ImportError: No module named vehicles [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] mod_wsgi (pid=11463): Exception occurred processing WSGI script '/opt/workshop/workshop.wsgi'. [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] Traceback (most recent call last): [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/handlers/wsgi.py", line 241, in __call__ [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] response = self.get_response(request) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/handlers/base.py", line 73, in get_response [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] response = middleware_method(request) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/middleware/common.py", line 56, in process_request [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] if (not _is_valid_path(request.path_info) and [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/middleware/common.py", line 142, in _is_valid_path [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] urlresolvers.resolve(path) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/urlresolvers.py", line 303, in resolve [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] return get_resolver(urlconf).resolve(path) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/urlresolvers.py", line 218, in resolve [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] sub_match = pattern.resolve(new_path) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/urlresolvers.py", line 216, in resolve [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] for pattern in self.url_patterns: [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/urlresolvers.py", line 245, in _get_url_patterns [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] patterns = getattr(self.urlconf_module, "urlpatterns", self.urlconf_module) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/core/urlresolvers.py", line 240, in _get_urlconf_module [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] self._urlconf_module = import_module(self.urlconf_name) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] File "/opt/python2.6/lib/python2.6/site-packages/django/utils/importlib.py", line 35, in import_module [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] __import__(name) [Wed Apr 21 15:17:48 2010] [error] [client 190.128.226.122] ImportError: No module named vehicles.urls Please give my a hand, i stuck... Obviously is a problem with my vehicle module (the only one in the app), another thing is that when i try: [root@localhost workshop]# python manage.py runserver 0:8000 The app runs perfectly, i think that the problem is something near the wsgi conf, something is not clicking.... Tks... Update: workshop dir looks like... [root@localhost workshop]# ls -l total 504 -rw-r--r-- 1 root root 22706 Apr 21 15:17 apache.custom.log -rw-r--r-- 1 root root 408141 Apr 21 15:17 apache.error.log -rw-r--r-- 1 root root 0 Apr 17 10:56 __init__.py -rw-r--r-- 1 root root 124 Apr 21 11:09 __init__.pyc -rw-r--r-- 1 root root 542 Apr 17 10:56 manage.py -rw-r--r-- 1 root root 3326 Apr 17 10:56 settings.py -rw-r--r-- 1 root root 2522 Apr 21 11:09 settings.pyc drw-r--r-- 4 root root 4096 Apr 17 10:56 templates -rw-r--r-- 1 root root 381 Apr 21 13:42 urls.py -rw-r--r-- 1 root root 398 Apr 21 13:00 urls.pyc drw-r--r-- 2 root root 4096 Apr 21 13:44 vehicles -rw-r--r-- 1 root root 38912 Apr 17 10:56 workshop.db -rw-r--r-- 1 root root 263 Apr 21 15:30 workshop.wsgi vehicles dir [root@localhost vehicles]# ls -l total 52 -rw-r--r-- 1 root root 390 Apr 17 10:56 admin.py -rw-r--r-- 1 root root 967 Apr 21 13:00 admin.pyc -rw-r--r-- 1 root root 732 Apr 17 10:56 forms.py -rw-r--r-- 1 root root 2086 Apr 21 13:00 forms.pyc -rw-r--r-- 1 root root 0 Apr 17 10:56 __init__.py -rw-r--r-- 1 root root 133 Apr 21 11:36 __init__.pyc -rw-r--r-- 1 root root 936 Apr 17 10:56 models.py -rw-r--r-- 1 root root 1827 Apr 21 11:36 models.pyc -rw-r--r-- 1 root root 514 Apr 17 10:56 tests.py -rw-r--r-- 1 root root 989 Apr 21 13:44 tests.pyc -rw-r--r-- 1 root root 1035 Apr 17 10:56 urls.py -rw-r--r-- 1 root root 1935 Apr 21 13:00 urls.pyc -rw-r--r-- 1 root root 3164 Apr 17 10:56 views.py -rw-r--r-- 1 root root 4081 Apr 21 13:00 views.pyc Update 2: this is my settings.py # Django settings for workshop project. DEBUG = True TEMPLATE_DEBUG = DEBUG ADMINS = ( ('Ignacio Rojas', '[email protected]'), ('Fabian Biedermann', '[email protected]'), ) MANAGERS = ADMINS DATABASE_ENGINE = 'sqlite3' DATABASE_NAME = '/opt/workshop/workshop.db' DATABASE_USER = '' DATABASE_PASSWORD = '' DATABASE_HOST = '' DATABASE_PORT = '' # Local time zone for this installation. Choices can be found here: # http://en.wikipedia.org/wiki/List_of_tz_zones_by_name # although not all choices may be available on all operating systems. # If running in a Windows environment this must be set to the same as your # system time zone. TIME_ZONE = 'America/Asuncion' # Language code for this installation. All choices can be found here: # http://www.i18nguy.com/unicode/language-identifiers.html LANGUAGE_CODE = 'es-py' SITE_ID = 1 # If you set this to False, Django will make some optimizations so as not # to load the internationalization machinery. USE_I18N = True # Absolute path to the directory that holds media. # Example: "/home/media/media.lawrence.com/" MEDIA_ROOT = '' # URL that handles the media served from MEDIA_ROOT. Make sure to use a # trailing slash if there is a path component (optional in other cases). # Examples: "http://media.lawrence.com", "http://example.com/media/" MEDIA_URL = '' # URL prefix for admin media -- CSS, JavaScript and images. Make sure to use a # trailing slash. # Examples: "http://foo.com/media/", "/media/". ADMIN_MEDIA_PREFIX = '/media/' # Make this unique, and don't share it with anybody. SECRET_KEY = '11y0_jb=+b4^nq@2-fo#g$-ihk5*v&d5-8hg_y0i@*9$w8jalp' MIDDLEWARE_CLASSES = ( 'django.middleware.common.CommonMiddleware', 'django.contrib.sessions.middleware.SessionMiddleware', 'django.contrib.auth.middleware.AuthenticationMiddleware', ) ROOT_URLCONF = 'workshop.urls' TEMPLATE_DIRS = ( # Put strings here, like "/home/html/django_templates" or "C:/www/django/templates". # Always use forward slashes, even on Windows. # Don't forget to use absolute paths, not relative paths. "/opt/workshop/templates" ) INSTALLED_APPS = ( 'django.contrib.admin', 'django.contrib.auth', 'django.contrib.contenttypes', 'django.contrib.sessions', 'django.contrib.sites', 'workshop.vehicles', ) TEMPLATE_CONTEXT_PROCESSORS = ( 'django.core.context_processors.auth', 'django.core.context_processors.debug', 'django.core.context_processors.i18n', 'django.core.context_processors.media', )

  Read the article

• Paperclip and xhr.sendAsBinary

  - by Denis

  Hi, I use paperclip to add a file to my model. I want to use the new feature of firefox 3.6, xhr.sendAsBinary, to send a file with an ajax request. Here is how I build my request : var xhr = new XMLHttpRequest(); xhr.open("POST", "/photos?authenticity_token=" + token + "&photo[name]=" + img.name + "&photo[size]=" + img.size); xhr.overrideMimeType('text/plain; charset=x-user-defined-binary'); xhr.sendAsBinary(bin); name and size are saved in my model without problem but the file itself is not catched by paperclip. my model class Photo < ActiveRecord::Base has_attached_file :photo, :styles => { :medium => "300x300>", :thumb => "100x100>" } end the migration def self.up add_column :photos, :photo_file_name, :string add_column :photos, :photo_content_type, :string add_column :photos, :photo_file_size, :integer add_column :photos, :photo_updated_at, :datetime end and my controller # POST /photos # POST /photos.xml def create @photo = Photo.new(params[:photo]) respond_to do |format| if @photo.save format.html { redirect_to(@photo, :notice => 'Photo was successfully created.') } format.xml { render :xml => @photo, :status => :created, :location => @photo } else format.html { render :action => "new" } format.xml { render :xml => @photo.errors, :status => :unprocessable_entity } end end end Any idea how to solve this issue? Thanks

  Read the article

• Draw to offscreen renderbuffer in OpenGL ES (iPhone)

  - by David Ensminger

  I'm trying to create an offscreen render buffer in OpenGL ES on the iPhone. I've created the buffer like this: glGenFramebuffersOES(1, &offscreenFramebuffer); glBindFramebufferOES(GL_FRAMEBUFFER_OES, offscreenFramebuffer); glGenRenderbuffersOES(1, &offscreenRenderbuffer); glBindRenderbufferOES(GL_RENDERBUFFER_OES, offscreenRenderbuffer); glFramebufferRenderbufferOES(GL_FRAMEBUFFER_OES, GL_COLOR_ATTACHMENT0_OES, GL_RENDERBUFFER_OES, offscreenRenderbuffer); But I'm confused on how to render the storage. Apple's documentation says to use the EAGLContext renderBufferStorage:fromDrawable: method, but this seems to only work for one render buffer (the main one being displayed). If I use the normal OpenGL function glRenderBufferStorageOES, then I can't seem to get it to display. Here's the code: // this is in the initialization section: glRenderbufferStorageOES(GL_RENDERBUFFER_OES, GL_RGB8_OES, backingWidth, backingHeight); // and this is when I'm trying to draw to it and display it: glBindFramebufferOES(GL_FRAMEBUFFER_OES, offscreenFramebuffer); GLfloat vc[] = { 0.0f, 0.0f, 0.0f, 10.0f, 10.0f, 10.0f, 0.0f, 0.0f, 0.0f, -10.0f, -10.0f, -10.0f, }; glLoadIdentity(); glEnableClientState(GL_VERTEX_ARRAY); glVertexPointer(3, GL_FLOAT, 0, vc); glDrawArrays(GL_LINES, 0, 4); glDisableClientState(GL_VERTEX_ARRAY); glBindRenderbufferOES(GL_RENDERBUFFER_OES, offscreenRenderbuffer); [context presentRenderbuffer:GL_RENDERBUFFER_OES]; Doing it this way, nothing is displayed on the screen. However, if I switch out the references to "offscreen...Buffer" to the buffers that were created with the renderBufferStorage method, it works fine. Any suggestions?

  Read the article

• WPF Memory Leak on XP (CMilChannel, HWND)

  - by vanja.

  My WPF application leaks memory at about 4kb/s. The memory usage in Task Manager climbs constantly until the application crashes with an "Out of Memory" exception. By doing my own research I have found that the problem is discussed here: http://stackoverflow.com/questions/801589/track-down-memory-leak-in-wpf and #8 here: http://blogs.msdn.com/jgoldb/archive/2008/02/04/finding-memory-leaks-in-wpf-based-applications.aspx The problem described is: This is a leak in WPF present in versions of the framework up to and including .NET 3.5 SP1. This occurs because of the way WPF selects which HWND to use to send messages from the render thread to the UI thread. This sample destroys the first HWND created and starts an animation in a new Window. This causes messages sent from the render thread to pile up without being processed, effectively leaking memory. The solution offered is: The workaround is to create a new HwndSource first thing in your App class constructor. This MUST be created before any other HWND is created by WPF. Simply by creating this HwndSource, WPF will use this to send messages from the render thread to the UI thread. This assures all messages will be processed, and that none will leak. But I don't understand the solution! I have a subclass of Application that I am using and I have tried creating a window in that constructor but that has not solved the problem. Following the instructions given literally, it looks like I just need to add this to my Application constructor: new HwndSource(new HwndSourceParameters("MyApplication"));

  Read the article

• MS SQL server and Trees

  - by Julian

  Im looking for some way of extrating data form a tree table as defined below. Table Tree Defined as :- TreeID uniqueidentifier TreeParent uniqueidentifier TreeCode varchar(50) TreeDesc varchar(100) Data some (23k rows), Parent Refs back into ID in table The following SQL renders the whole tree (takes arround 2 mins 30) I need to do the following. 1) Render each Tree Node with its LVL 1 parent 2) Render all nodes that have a Description that matches a TreeDesc like 'SomeText%' 3) Render all parent nodes that are for a single tree id. Items 2 and 3 take 2mins30 so this needs to be a lot faster! Item 1, just cant work out how to do it with out killing SQL or taking forever any sugestions would be helpfull Thanks Julian WITH TreeCTE(TreeCode, TreeDesc, depth, TreeParent, TreeID) AS ( -- anchor member SELECT cast('' as varchar(50)) as TreeCode , cast('Trees' as varchar(100)) as TreeDesc, cast('0' as Integer) as depth, cast('00000000-0000-0000-0000-000000000000' as uniqueidentifier) as TreeParent, cast('00000000-0000-0000-0000-000000000000' as uniqueidentifier) as TreeID UNION ALL -- recursive member SELECT s.TreeCode, s.TreeDesc, cte.depth+1, isnull(s.TreeParent, cast('00000000-0000-0000-0000-000000000000' as uniqueidentifier)), isnull(s.TreeID, cast('00000000-0000-0000-0000-000000000000' as uniqueidentifier)) FROM pdTrees AS S JOIN TreeCTE AS cte ON isnull(s.TreeParent, cast('00000000-0000-0000-0000-000000000000' as uniqueidentifier)) = isnull( cte.TreeID , cast('00000000-0000-0000-0000-000000000000' as uniqueidentifier)) ) -- outer query SELECT s.TreeID, s.TreeCode, s.TreeDesc, s.depth, s.TreeParent FROM TreeCTE s

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >