Search Results

Search found 18096 results on 724 pages for 'let'.

Page 680/724 | < Previous Page | 676 677 678 679 680 681 682 683 684 685 686 687  | Next Page >

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

  Read the article

• How to use more than 3 virtual disks in Linux using CentOS and XenServer

  - by 010110110101

  I've attached 5 virtual disks to a Virtual Machine in Citrix XenServer. The VM has the xs-tools installed. Initially it said that it couldn't add so many disks. After I installed the xs-tools, it let me add all the disks. But /dev doesn't show all the disks. It shows these: /dev/xvda /dev/xvdb /dev/xvdc /dev/cdrom Perhaps it is bound by the limits of an IDE bus? (3 disks + CD-ROM) If so, how does one change the VM to use SCSI? Edit: According to the documentation: 2.6.3. VM Block Devices In the PV Linux case, block devices are passed through as PV devices. XenServer does not attempt to emulate SCSI or IDE, but instead provides a more suitable interface in the virtual environment in the form of xvd* devices. It is also possible to get an sd* device using the same mechanism, where the PV driver inside the VM takes over the SCSI device namespace. This is not desirable so it is best to use xvd* where possible for PV guests (this is the default for Debian and RHEL). For Windows or other fully virtualized guests, XenServer emulates an IDE bus in the form of an hd* device. When using Windows, installing the Citrix Tools for Virtual Machines installs a special PV driver that works in a similar way to Linux, except in the fully virtualized environment. Still, with 5 virtual disks attached, I don't see the other xvd devices. Edit #2: (attached requested info) Host Machine: XenServer 6.1 Linux version 2.6.32.43-0.4.1.xs1.6.10.777.170770xen (geeko@buildhost) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-51)) #1 SMP Wed Apr 17 05:52:03 EDT 2013 Guest Machine: CentOS release 6.4 (Final) Linux version 2.6.32-358.6.2.el6.x86_64 ([email protected]) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Thu May 16 20:59:36 UTC 2013 Output of 'fdisk -l' on Guest Machine: Note, the disk beyond the first 3 attached are not displaying -- there should be 4 100GB disks. (There are a total of 5 disks displayed in XenCenter -- 16GB, 100GB, 100GB, 100GB, 100GB) Disk /dev/xvdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfb6c95b9 Device Boot Start End Blocks Id System /dev/xvdb1 1 13054 104856223+ 83 Linux Disk /dev/xvda: 17.2 GB, 17179869184 bytes 255 heads, 63 sectors/track, 2088 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e5f41 Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2089 16264192 8e Linux LVM Disk /dev/xvdc: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed249ced Device Boot Start End Blocks Id System /dev/xvdc1 1 13054 104856223+ 83 Linux Disk /dev/mapper/vg_blue-lv_root: 14.6 GB, 14571012096 bytes 255 heads, 63 sectors/track, 1771 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_blue-lv_swap: 2080 MB, 2080374784 bytes 255 heads, 63 sectors/track, 252 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 I see that the Linux versions say SMP. The Guest VM doesn't say "xen" in the name. However, I have already run yum install kernel-xen. Could be a clue?

  Read the article

• How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

  Read the article

• Wear and tear on server hard drive from filesystem polling by PHP script

  - by jackie

  So I'm working on a discussion platform, and various clients will visit http://host/thread.php, which will render the discussion thread to date in addition to a form to submit a new post. When a new post is submitted, I would like all of the other clients with browser windows open to have it appear in near-real-time. One of the constraints of my script is that it may not use a DBMS and it must stay in the filesystem. Additionally, I can't use any PECL/PEAR extensions like inotify or anything like that for IPC. The flow will look like this: Client A requests thread.php and the thread is so far empty, but nonetheless it opens a Server-Side Event at eventPusher.php. Client B does the same. Client A fills out a post in the form and and submits (POSTs) it to subHandler.php. ??? (subHandler stores the new submission into the main thread storefile which gets read from when a fresh, new client requests thread.php, in addition to somehow signalling to the continually-running eventPusher event-source that a new comment was posted and that it should echo the event-json to the client. How, exactly, it will send this signal I'm yet unsure of, but there are a few options that I've thought of -- this is the crux of the question, so see below for more clarification) eventPusher.php happily pushes the new event to the client and it shows up soon after it was originally submitted on all clients who have the page open's screens. Now for the #4 missing-link mystery-step, I see a few problems. I mean, either way, eventPusher is gonna be doing a while loop of some sort -- it's gonna be polling something, I think that much is clear. (If that's a bad assumption please do let me know.) Now, the simplest way would be subHandler gets invoked on the form submission, writes it to the main store in addition to newComments.xml, then exits without doing anything else. Then eventPusher checks in newComments.xml every X seconds (by the way, what would be a reasonable time interval here?) and if it finds something then it emits an event to the client. Now, my fear with this is that the server's hard drive will have to constantly start spinning up. Maybe this isn't the case, perhaps it would just get cached in RAM and the linux kernel would take care of this transparently such that filesystem access doesn't actually engage the device because the kernel knows that that particular file hasn't changed since last read. * idea #2: I have no idea how to go about this, but perhaps there is a variable scope that gets stored in general RAM on the system which can be read by any process. Like if we mega-exported a bash variable so that $new_post is normally false but it gets toggled to true by subHandler, and then back to flase once it's pushed to the client. I doubt there's such a variable scope in PHP directly, but I struggle with the concept of variable scope, I just can't seem to understand it no matter what I read on it. * idea #3: eventPusher queries ps in its whileloop for another instance of itself. If there's not another eventPusher active then it's highly unlikely that new comments will be getting submitted. It's okay if this only works =90% of the time, it doesn't need to be completely foolproof. * idea #4: eventPusher queries DMESG to see if that file's been written to recently. So to sum everything up, I need to have inter-php-script-communication in near-real-time that will work on a standard mod_php shared hosting setup without any elevated privileges, PHP addon modules, or other system adjustments that can't be done from the PHP script itself at runtime. With*out* spinning up the drive more than a few times. No SQL servers either. Apologies if my english isn't the best, I'm still trying to improve on it.

  Read the article

• how to use ajax with json in ruby on rails

  - by rafik860

  I am implemeting a facebook application in rails using facebooker plugin, therefore it is very important to use this architecture if i want to update multiple DOM in my page. if my code works in a regular rails application it would work in my facebook application. i am trying to use ajax to let the user know that the comment was sent, and update the comments bloc. migration: class CreateComments < ActiveRecord::Migration def self.up create_table :comments do |t| t.string :body t.timestamps end end def self.down drop_table :comments end end controller: class CommentsController < ApplicationController def index @comments=Comment.all end def create @comment=Comment.create(params[:comment]) if request.xhr? @comments=Comment.all render :json=>{:ids_to_update=>[:all_comments,:form_message], :all_comments=>render_to_string(:partial=>"comments" ), :form_message=>"Your comment has been added." } else redirect_to comments_url end end end view: <script> function update_count(str,message_id) { len=str.length; if (len < 200) { $(message_id).innerHTML="<span style='color: green'>"+ (200-len)+" remaining</span>"; } else { $(message_id).innerHTML="<span style='color: red'>"+ "Comment too long. Only 200 characters allowed.</span>"; } } function update_multiple(json) { for( var i=0; i<json["ids_to_update"].length; i++ ) { id=json["ids_to_update"][i]; $(id).innerHTML=json[id]; } } </script> <div id="all_comments" > <%= render :partial=>"comments/comments" %> </div> Talk some trash: <br /> <% remote_form_for Comment.new, :url=>comments_url, :success=>"update_multiple(request)" do |f|%> <%= f.text_area :body, :onchange=>"update_count(this.getValue(),'remaining');" , :onkeyup=>"update_count(this.getValue(),'remaining');" %> <br /> <%= f.submit 'Post'%> <% end %> <p id="remaining" >&nbsp;</p> <p id="form_message" >&nbsp;</p> <br><br> <br> if i try to do alert(json) in the first line of the update_multiple function , i got an [object Object]. if i try to do alert(json["ids_to_update"][0]) in the first line of the update_multiple function , there is no dialog box displayed. however the comment got saved but nothing is updated. it seems like the object sent by rails is nil or cant be parsed by JSON.parse(json). questions: 1.how can javascript and rails know that i am dealing with json objects?deos ROR sent it a object format or a text format?how can it check that the json object has been sent 2.how can i see what is the returned json?do i have to parse it?how? 2.how can i debug this problem? 3.how can i get it to work?

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• File copying utility like rsync with error handling like ddrescue, for data recovery from a hard drive with bad sectors or hardware failure

  - by purefusion

  I have a hard drive with either bad blocks or sectors that are failing to read due to potential mechanical issues, such as a bad disk head, bad motor, or some other issue that is causing the hard drive to read data excruciatingly slowly and with lots of read errors. I'm seeing an average of 50 KB/sec, with some reads dropping below 10 KB/sec, and frequently it gets stuck on a file or sector altogether, usually for quite a long time—from 2-10 minutes or more (when using rsync, before it times out). Speed seems to vary wildly, and it gets stuck on files a lot, and when it finally gets "unstuck" it only seems to last for a short burst before it gets stuck again. The drive is also very quiet with only an occasional sound of files copying (usually when it gets stuck/unstuck for a brief time, before getting stuck again). Thus, there are none of those evil sounds that are normally associated with HDD death. Someone suggested that the problems sounded like they might be caused by a misaligned disk head, which requires a lot of re-reads before it finally reads data with success. Sounds plausible, but I digress... Anyway, the problem with rsync is that it seems to have no decent error handling support. Obviously, it wasn't meant for use in recovering data from failing hard drives, but all the so-called "data recovery" utilities out there that are meant for such use usually focus on recovery of deleted files or messed up partitions, rather than copying files off dying hard drives. Deleted file recovery is not what I need, obviously, so perhaps you can understand my disappointment in not being able to find what I'm after yet. Naturally, this is where you'd probably say "You should use ddrescue!" Well, that's all fine and dandy, but I've already got most of the data backed up, so I just want to recover certain files. I'm not concerned with trying to recover a full partition block-by-block as ddrescue does. I am only interested in rescuing just specific files and directories. Ideally, what I'd like is some sort of cross between rsync and ddrescue: something that lets me specify source and destination as directories of normal files like rsync (rather than two full partitions as ddrescue requires), with a way to skip files with errors in an initial run, and then allows me to attempt recovery of those files with errors in a later run (with a slightly altered command, of course), perhaps even offering an option to specify the number of retry attempts ...just like how ddrescue works with blocks, only I want a utility that works with specific files/directories like rsync does. So am I daydreaming here, or does something out there exist that can do this? Or, maybe even a way to make rsync or ddrescue work in such a way? I'm really open to whatever solutions might work, so long as they let me choose which files I want to "rescue", and can skip files with errors in the initial run, and try/retry those errors again later. So far I've tried rsync with the following options, but it often gets stuck on a file for longer than the timeout, and ideally I'd just like it to move on to the next file and come back later to the files it gets stuck on. I don't think that's possible though. Anyway, here's what I've been using up till now: rsync -avP --stats --block-size=512 --timeout=600 /path/to/source/* /path/to/destination/

  Read the article

• mysqld service crashes on restart, after importing mysqldump #innodb

  - by ubunut

  I have 2 mysql servers. Let's call them server01 & server02. Both have the same configuration: mysqladmin Ver 8.42 Distrib 5.1.61, for redhat-linux-gnu on x86_64 [client] default-character-set=utf8 [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 max_allowed_packet = 16M default-character-set=utf8 default-collation=utf8_unicode_ci character-set-server=utf8 collation-server=utf8_unicode_ci default-storage-engine = InnoDB innodb_data_home_dir = /var/lib/mysql innodb_log_group_home_dir = /var/lib/mysql innodb_data_file_path = ibdata1:10M:autoextend innodb_additional_mem_pool_size = 2M innodb_log_file_size = 5M innodb_log_buffer_size = 8M innodb_lock_wait_timeout = 50 innodb_flush_log_at_trx_commit = 1 innodb_buffer_pool_size = 700M table_cache = 300 thread_cache_size = 4 query_cache_size = 200m query_cache_limit = 10m [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid I make a mysqldump on server01: mysqldump -uuser -ppassword --all-databases testservers.sql (most tables in these databases are innodb, some of the mysql.* tables are Innodb too) Then I import the testservers.sql on server02: mysql -uuser < testservers.sql (mysqld has been started with --skip-network). So far so good, I can login into mysql & everything seems to be ok. BUT when I exit to the shell and execute service mysqld restart, The service fails to start. stack-trace in /var/log/mysqld.log: 121022 14:53:19 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 121022 14:53:19 [Warning] '--default-character-set' is deprecated and will be removed in a future release. Please use '--character-set-server' instead. 121022 14:53:19 [Warning] '--default-collation' is deprecated and will be removed in a future release. Please use '--collation-server' instead. 12:53:19 UTC - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=8384512 read_buffer_size=131072 max_used_connections=0 max_threads=151 thread_count=0 connection_count=0 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 338324 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. Thread pointer: 0x267e630 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 7fff3efe0be0 thread_stack 0x40000 /usr/libexec/mysqld(my_print_stacktrace+0x29) [0x84bd89] /usr/libexec/mysqld(handle_fatal_signal+0x483) [0x6a0be3] /lib64/libpthread.so.0() [0x338d60f500] /usr/libexec/mysqld(ha_resolve_by_name(THD*, st_mysql_lex_string const*)+0x81) [0x6956e1] /usr/libexec/mysqld(open_table_def(THD*, st_table_share*, unsigned int)+0xe0a) [0x60e5ba] /usr/libexec/mysqld(get_table_share(THD*, TABLE_LIST*, char*, unsigned int, unsigned int, int*)+0x20b) [0x602b0b] /usr/libexec/mysqld() [0x603597] /usr/libexec/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x7a1) [0x6079a1] /usr/libexec/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5d0) [0x608570] /usr/libexec/mysqld(open_and_lock_tables_derived(THD*, TABLE_LIST*, bool)+0x6a) [0x60877a] /usr/libexec/mysqld(plugin_init(int*, char**, int)+0x622) [0x715af2] /usr/libexec/mysqld() [0x5bd3b2] /usr/libexec/mysqld(main+0x1b3) [0x5bfc93] /lib64/libc.so.6(__libc_start_main+0xfd) [0x338d21ecdd] /usr/libexec/mysqld() [0x5087b9] Trying to get some variables. Some pointers may be invalid and cause the dump to abort. Query (0): is an invalid pointer Connection ID (thread ID): 0 Status: NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 121022 14:53:19 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended A typical mysqdump entry looks like this: DROP TABLE IF EXISTS `adodb_logsql`; /*!40101 SET @saved_cs_client = @@character_set_client */; /*!40101 SET character_set_client = utf8 */; CREATE TABLE `adodb_logsql` ( `id` bigint(10) unsigned NOT NULL AUTO_INCREMENT, `created` datetime NOT NULL, `sql0` varchar(250) NOT NULL DEFAULT '', `sql1` text, `params` text, `tracer` text, `timer` decimal(16,6) NOT NULL DEFAULT '0.000000', PRIMARY KEY (`id`) ) ENGINE=InnoDB DEFAULT CHARSET=utf8 COMMENT='to save some logs from ADOdb'; /*!40101 SET character_set_client = @saved_cs_client */; IF I change all occurrences of "ENGINE=InnoDB" to "ENGINE=MyISAM" before import, then the service has no problem restarting. I'm quite puzzled as to what's happening, maybe I'm just an idiot, then by all means tell me so. Any help would be greatly appreciated!

  Read the article

• Windows 7 inbuilt and 3rd party (de)fragmentation related queries

  - by Karan

  I have a pretty good idea of how files end up getting fragmented. That said, I just copied ~3,200 files of varying sizes (from a few KB to ~20GB) from an external USB HDD to an internal, freshly formatted (under Windows 7 x64), NTFS, 2TB, 5400RPM, WD, SATA, non-system (i.e. secondary) drive, filling it up 57%. Since it should have been very much possible for each file to have been stored in one contiguous block, I expected the drive to be fragmented not more than 1-2% at most after this rather lengthy exercise (unfortunately this older machine doesn't support USB 3.0). Windows 7's inbuilt defrag utility told me after a quick analysis that the drive was fragmented only 1% or so, which dovetailed neatly with my expectations. However, just out of curiosity I downloaded and ran the latest portable x64 version of Piriform's Defraggler, and was shocked to see the drive being reported as being ~85% fragmented! The portable version of Auslogics Disk Defrag also agreed with Defraggler, and both clearly expected to grind away for ~10 hours to completely defragment the drive. 1) How in blazes could the inbuilt and 3rd party defrag utils disagree so badly? I mean, 10-20% variance is probably understandable, but 1% and 85% are miles apart! This Engineering Windows 7 blog post states: In Windows XP, any file that is split into more than one piece is considered fragmented. Not so in Windows Vista if the fragments are large enough – the defragmentation algorithm was changed (from Windows XP) to ignore pieces of a file that are larger than 64MB. As a result, defrag in XP and defrag in Vista will report different amounts of fragmentation on a volume. ... [Please read the entire post so the quote is not taken out of context.] Could it simply be that the 3rd party defrag utils ignore this post-XP change and continue to use analysis algos similar to those XP used? 2) Assuming that the 3rd party utils aren't lying about the real extent of fragmentation (which Windows is downplaying post-XP), how could the files have even got fragmented so badly given they were just copied over afresh to an empty drive? 3) If vastly differing analysis algos explain the yawning gap, which do I believe? I'm no defrag fanatic for sure, but 85% is enough to make me seriously consider spending 10 hours defragging this drive. On the other hand, 1% reported by Windows' own defragger clearly implies that there is no cause for concern and defragging would actually have negative consequences (as per the post). Is Windows' assumption valid and should I just let it be, or will there be any noticeable performance gains after running one of the 3rd party utils for 10 hours straight? 4) I see that out of the box Windows 7 defrag is scheduled to run weekly. Does anyone know whether it defrags every single time, or only if its analysis reveals a fragmentation percentage over a set threshold? If the latter, what is this threshold and can it be changed, maybe via a Registry edit? Thanks for reading through (my first query on this wonderful site!) and for any helpful replies. Also, if you're answering question #3, please keep in mind that any speed increases post defragging with 3rd party utils vis-à-vis Windows' inbuilt program should not include pre-Vista (preferably pre-Win7) examples. Further, examples of programs that made your system boot faster won't help in this case, since this is a non-system drive (although one that'll still be used daily).

  Read the article

• Windows Service SearchIndexer.exe Crashes on Indexing

  - by Josh Jay

  Relevant Specs: Windows 7 Professional 64-bit SP1 Outlook 2010 Version 14.0.7116.5000 (32-bit) Original Symptom: In outlook, I attempted to search for an email but nothing ever returned and the indicator kept going like it was searching. Attempted Resolutions: I investigated the search options and with some research noticed the Windows Service "Windows Search" (SearchIndexer.exe) was not running. I attempted to start it but I receive this error message: "Windows could not start the Windows Search service on Local Computer. Error 1067: The process terminated unexpectedly." The Event Viewer gives this error entry: Log Name: Application Source: Application Error Date: 6/3/2014 11:02:05 AM Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Computer: ***REMOVED FOR POST*** Description: Faulting application name: SearchIndexer.exe, version: 7.0.7601.17610, time stamp: 0x4dc0d019 Faulting module name: KERNELBASE.dll, version: 6.1.7601.18229, time stamp: 0x51fb1677 Exception code: 0xc0000005 Fault offset: 0x000000000000940d Faulting process id: 0x6a0 Faulting application start time: 0x01cf7f3cc83757c6 Faulting application path: C:\Windows\system32\SearchIndexer.exe Faulting module path: C:\Windows\system32\KERNELBASE.dll Report Id: 06424160-eb30-11e3-9555-843a4b07b336 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Application Error" /> <EventID Qualifiers="0">1000</EventID> <Level>2</Level> <Task>100</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2014-06-03T15:02:05.000000000Z" /> <EventRecordID>602923</EventRecordID> <Channel>Application</Channel> <Computer>M6700-12011.ncaa.org</Computer> <Security /> </System> <EventData> <Data>SearchIndexer.exe</Data> <Data>7.0.7601.17610</Data> <Data>4dc0d019</Data> <Data>KERNELBASE.dll</Data> <Data>6.1.7601.18229</Data> <Data>51fb1677</Data> <Data>c0000005</Data> <Data>000000000000940d</Data> <Data>6a0</Data> <Data>01cf7f3cc83757c6</Data> <Data>C:\Windows\system32\SearchIndexer.exe</Data> <Data>C:\Windows\system32\KERNELBASE.dll</Data> <Data>06424160-eb30-11e3-9555-843a4b07b336</Data> </EventData> </Event> The regular windows search (from start menu) works fine, and if I reboot the machine the service starts up OK but as soon as it kicks off when I let the machine idle for long enough it crashes (same Event Viewer entry). We also tried the Microsoft Utility to no avail. Has anyone seen this issue before?

  Read the article

• Dell Latitude E6430 Docking Station + Dual Monitor + Laptop Screen Tri-Monitor setup

  - by Larry

  I have a company issued laptop and docking station as well as two monitors The specifications of the hardware are as follows; Laptop: Latitude E6430 BIOS: A02.00 Processor: i7-3720QM CPU @ 2.60 (8 CPUs) Memory: 4096MB RAM Page file: 1825MB used, 4793MB available DirectX 11 Display Driver/Chip: MVIDIA NVS 5200M DAC: Integrated RAMDAC Aprox Total Memory: 2376 (Above 3 details same for both displays) Current Display Mode (Display 1): 1600x900 Current Display Mode (Display 2): 1440x900 the docking station is a Dell Latitude E6420 Docking Station PR03X Port Replicator and I don't think the monitor model is particularly relevant to resolving this issue but they are both Acer V193Ws The story goes like this; the laptop works fine if I VGA one monitor into the laptop through the vga port on the back of the lefthand side of the laptop I can achieve dual monitor display fine (laptop screen + monitor) if I plug the laptop into the docking station and use the vga port in the back of the docking station I can dual monitor fine (laptop screen + monitor) if I plug the laptop into the docking station, the laptop's lefthand side VGA port no longer seems to function at all I've spoken to internal IT about this issue and they're going to get me some kind of VGA splitter or a DVI-VGA adapter to use with the docking station for the second Acer Monitor, but that isn't going to happen for a few days. So I guess what I'm wondering is; is there any way to continue to use the side VGA port on my laptop while using the docking station VGA port? and as a secondary 'followup' pending resolution of the initial issue with getting both monitors up and running (at the moment I have both monitors on my desk but am just using my laptop screen as one of my dual monitor display with one of the monitors [the one connected to dock]), is there any way to CONTINUE to use my laptop monitor to in effect have a triple monitor display (2 monitors + docked laptop)? I am wondering this because internal IT told me that they were aware of some issues with the particular display drivers in my box and triple monitor displays but weren't really going to look TOO much in-depth into that (which is perfectly understandable) since getting the adapter for the dual monitors up and running was the greater priority within their purview. So this is a two parter; Can I dual monitor using two vga cables with 1 docking station vga port and one laptop vga port? is there a setting that can be tweaked somewhere? because plugging the box into the station seems to make the side port stop working and... Is there any reasonably simple and cost-effective work around (e.g. I am find with shelling out maybe a few dollars out of my own pocket for some hardware or software to make my company box tri-display capable) but if this requires some extensive rebuild or new OSs or doing stuff to the BIOS I'd rather have a straight answer about this being untenable as a slight modification to a (once again) company laptop and stop wasting time looking into it Thanks! and please let me know if you guys need any more details (tech specs or something) to answer this question [EDIT] 2/10/2014 Just an update; turned out it really was just a hardware limitation issue. The old laptop just couldn't hack it. Got a new laptop with a better video card and different monitors from my company and am successfully using a triple display currently (2 monitors + laptop screen)

  Read the article

• How do I resolve "conflicting accounts" in google apps without breaking links to online photos on picasa?

  - by lee

  I have been using google apps for some time, and only recently learned I have what google calls "conflicting accounts" which is creating a problem I haven't been able to resolve. Turns out that the apps account really only covers email, google docs, and the calendar and not other features like picasa, blogger, youtube etc. and at some point they gave me a non-apps google account with my same (proprietary non-gmail) email address for the additional apps. This is the "conflicting account." I had noticed that I sometimes had to come in through another door when I went back and forth, between docs, picasa, and mail let's say, but never understood why since it was the same username and password and I didn't get any communication about it at the time. Google is now in the process of giving google apps users access to the additional apps and providing instructions for consolidating the two accounts. But if I want to move my picasa site into the new apps structure I have to download my albums and re-synch them. This would be disastrous for me as I have hundreds of photos embedded in my websites, and new web addresses would break all the connections. The alternative seems to be to rename my "personal" (non-apps) accounts as described at http://www.google.com/support/a/bin/answer.py?answer=185186: Users with conflicting Google Accounts can easily resolve their conflicts by renaming their personal Google Accounts, and the data in their personal accounts will remain safe and accessible to them. Here’s how a user can rename their personal Google Account: * Step 1: Visit www.google.com/accounts and sign in with your personal Google Account * Step 2: Click ‘Change email’ under ‘Personal Settings’ * Step 3: Enter a different email address where you can receive mail, enter your password, and click ‘Save email address’ * Step 4: Check your other email If your users don’t have different email addresses where they can receive mail, they can resolve the conflict by renaming their personal Google Accounts to @gmail.com addresses instead. Sounds easy enough, right? I gave them a gmail address. The wizard said "sorry you can't use a gmail account for this" --which contradicts the last paragraph above but ok, I switched to a new email address I just created for one of my domains. I can send email back and forth between this account and my google apps account with no problem. But when I try to use it as a replacement on the "personal" side I always get "The password you gave is incorrect." I have tried it over and over and know the password is correct. Since I like to get all my emails though one web interface I initially had the new email set up as an add-on to my google apps email account, but noting that the instructions said the "personal account" email could not be associated with any other gmail account I took it off and went back to accessing it via horde so there would be no conflict there, which seemed to make no difference. I can't figure out why it won't accept the password. Does anyone have any thoughts about that? or suggestions for another way to resolve my picasa problem? any help at all is greatly appreciated. Lee

  Read the article

• Cannot connect to website - SSL handshaking fails

  - by ravenspoint

  So I cannot connect to certain websites. Just a few, most are OK. The one I really care about is paypal.com. I have done the usual things. Let's see: Checked my etc/hosts Flushed the DNS cache Checked firewall Switched on & off virus protection Switched on and off ad blocking pinged the sites Eventually, I decided to look at what curl is saying in detail == Info: About to connect() to www.paypal.com port 443 (#0) == Info: Trying 66.211.169.2... == Info: connected == Info: SSLv3, TLS handshake, Client hello (1): => Send SSL data, 110 bytes (0x6e) 0000: 01 00 00 6a 03 01 4f 6c aa 8c 57 2b 3d 1e 74 64 ...j..Ol..W+=.td 0010: c1 27 25 a5 3a 12 7f 3f 41 0a 17 15 2e c9 67 7c .'%.:.?A.....g| 0020: b3 e1 f6 9a db a9 00 00 2a 00 39 00 38 00 35 00 ........*.9.8.5. 0030: 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 05 00 ......3.2./..... 0040: 04 00 15 00 12 00 09 00 14 00 11 00 08 00 06 00 ................ 0050: 03 00 ff 01 00 00 17 00 00 00 13 00 11 00 00 0e ................ 0060: 77 77 77 2e 70 61 79 70 61 6c 2e 63 6f 6d www.paypal.com (hangs here for ever) This looks to me like paypal is refusing to reply to the first SSL handshake. I don't know much about SSL, but compaing to the output from a site that works for me seems to make it obvious == Info: About to connect() to www.cibc.com port 443 (#0) == Info: Trying 159.231.80.200... == Info: connected == Info: SSLv3, TLS handshake, Client hello (1): => Send SSL data, 108 bytes (0x6c) 0000: 01 00 00 68 03 01 4f 6c ad 6a 1f 67 d5 84 c4 4b ...h..Ol.j.g...K 0010: 0d 49 ae d6 b9 5b c3 63 f9 48 aa 18 da 43 d1 32 .I...[.c.H...C.2 0020: 47 ae 17 e5 cd e9 00 00 2a 00 39 00 38 00 35 00 G.......*.9.8.5. 0030: 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 05 00 ......3.2./..... 0040: 04 00 15 00 12 00 09 00 14 00 11 00 08 00 06 00 ................ 0050: 03 00 ff 01 00 00 15 00 00 00 11 00 0f 00 00 0c ................ 0060: 77 77 77 2e 63 69 62 63 2e 63 6f 6d www.cibc.com == Info: SSLv3, TLS handshake, Server hello (2): <= Recv SSL data, 74 bytes (0x4a) 0000: 02 00 00 46 03 01 00 00 58 cf 26 e2 e1 65 db 11 ...F....X.&..e.. 0010: bc 6f 26 7b 3b 6d eb 14 5f ad 47 dd 86 ea 4d a3 .o&{;m.._.G...M. 0020: fb 9f b7 2a 54 3e 20 5f 6b 04 5a 12 38 64 5d 18 ...*T> _k.Z.8d]. 0030: 65 9e e9 cd 61 eb 91 c1 16 25 61 30 bb 08 2a 78 e...a....%a0..*x 0040: b8 ee b8 7e f2 65 6a 00 04 00 ...~.ej... == Info: SSLv3, TLS handshake, CERT (11): ... and so on - working nicely eventually get some nice HTML Now I am reaaly stuck. This has been going on for five days, so I am pretty sure that the problem is not with paypal. But what on my system could be interfering with the SSL handshaking done by curl with this particular site? I suppose I could not be offering any certificates that PayPal accepts, but wouldn't I get a reply telling me so, or at least giving an error?

  Read the article

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• Trying to connect phpMyAdmin to remote mySQL server ( 2002: can't connect )

  - by Malcolm Jones

  Trying to get phpMyAdmin to talk to a remote mySQL server. The config is below and there is already a user set up in mySQL DB to be able to log in from the specified host that PMA sits on. Hosting is provided by Rackspace (Rightscale) and both cloud servers behind the same firewall. [config.inc.php] <?php $cfg['blowfish_secret'] = ''; $i = 0; $i++; $cfg['Servers'][$i]['host'] = 'XX.XX.XX.XX'; // MySQL hostname or IP address $cfg['Servers'][$i]['port'] = ''; // MySQL port - leave blank for default port $cfg['Servers'][$i]['socket'] = ''; // Path to the socket - leave blank for default socket $cfg['Servers'][$i]['connect_type'] = 'tcp'; // How to connect to MySQL server ('tcp' or 'socket') $cfg['Servers'][$i]['extension'] = 'mysql'; // The php MySQL extension to use ('mysql' or 'mysqli') $cfg['Servers'][$i]['compress'] = FALSE; // Use compressed protocol for the MySQL connection // (requires PHP >= 4.3.0) $cfg['Servers'][$i]['controluser'] = ''; // MySQL control user settings // (this user must have read-only $cfg['Servers'][$i]['controlpass'] = ''; // access to the "mysql/user" // and "mysql/db" tables). // The controluser is also // used for all relational // features (pmadb) $cfg['Servers'][$i]['auth_type'] = 'config'; // Authentication method (config, http or cookie based)? $cfg['Servers'][$i]['user'] = 'USERNAME'; // MySQL user $cfg['Servers'][$i]['password'] = 'PASSWORD'; // MySQL password (only needed // with 'config' auth_type) $cfg['Servers'][$i]['only_db'] = ''; // If set to a db-name, only // this db is displayed in left frame // It may also be an array of db-names, where sorting order is relevant. $cfg['Servers'][$i]['hide_db'] = ''; // Database name to be hidden from listings $cfg['Servers'][$i]['verbose'] = ''; // Verbose name for this host - leave blank to show the hostname $cfg['Servers'][$i]['pmadb'] = ''; // Database used for Relation, Bookmark and PDF Features // (see scripts/create_tables.sql) // - leave blank for no support // DEFAULT: 'phpmyadmin' $cfg['Servers'][$i]['bookmarktable'] = ''; // Bookmark table // - leave blank for no bookmark support // DEFAULT: 'pma_bookmark' $cfg['Servers'][$i]['relation'] = ''; // table to describe the relation between links (see doc) // - leave blank for no relation-links support // DEFAULT: 'pma_relation' $cfg['Servers'][$i]['table_info'] = ''; // table to describe the display fields // - leave blank for no display fields support // DEFAULT: 'pma_table_info' $cfg['Servers'][$i]['table_coords'] = ''; // table to describe the tables position for the PDF schema // - leave blank for no PDF schema support // DEFAULT: 'pma_table_coords' $cfg['Servers'][$i]['pdf_pages'] = ''; // table to describe pages of relationpdf // - leave blank if you don't want to use this // DEFAULT: 'pma_pdf_pages' $cfg['Servers'][$i]['column_info'] = ''; // table to store column information // - leave blank for no column comments/mime types // DEFAULT: 'pma_column_info' $cfg['Servers'][$i]['history'] = ''; // table to store SQL history // - leave blank for no SQL query history // DEFAULT: 'pma_history' $cfg['Servers'][$i]['verbose_check'] = TRUE; // set to FALSE if you know that your pma_* tables // are up to date. This prevents compatibility // checks and thereby increases performance. $cfg['Servers'][$i]['AllowRoot'] = TRUE; // whether to allow root login $cfg['Servers'][$i]['AllowDeny']['order'] // Host authentication order, leave blank to not use = ''; $cfg['Servers'][$i]['AllowDeny']['rules'] // Host authentication rules, leave blank for defaults = array(); Please let me know if you need anymore info. -- Malcolm

  Read the article

• cannot send mail to postfix /w iptables linux proxy

  - by Juzzam

  I have two separate servers, both running Ubuntu 8.04. Server 1 has the real domain name of our site, let's refer to it as example.com. Server 2 is a mail server I have setup with postfix/courier. The hostname for this server is mail.example.com. I've setup iptables on Server 1 to forward all traffic on port 25 to Server 2. I used this script (except I changed the target ip address and the port from 80 to 25). When I send an email to [email protected] it works. However, when I try to send an email to [email protected] from gmail, I get this error: 550 550 #5.1.0 Address rejected [email protected] (state 14) /var/log/mail.log shows no new lines when this happens. What is strange is that it works with telnet from my local machine. For example: $ telnet example.com 25 220 VO13421.localdomain SMTP Postfix EHLO example.com 250-VO13421.localdomain 250-PIPELINING 250-SIZE 10240000 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN MAIL FROM: [email protected] 250 2.1.0 Ok RCPT TO: [email protected] 250 2.1.5 Ok data 354 Please start mail input. hello user... how have you been? . 250 Mail queued for delivery. quit 221 Closing connection. Good bye. /var/log/mail.log shows success (and the email goes to the maildr): Feb 24 09:47:36 VO13421 postfix/smtpd[2212]: connect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: 65C68120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: 6BDFA120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/cleanup[2216]: 6BDFA120321: message-id= Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: from=, size=395, nrcpt=1 (queue active) Feb 24 09:48:29 VO13421 postfix/virtual[2217]: 6BDFA120321: to=, relay=virtual, delay=0.28, delays=0.25/0.02/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: removed Feb 24 09:48:30 VO13421 postfix/smtpd[2212]: disconnect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] iptables -L -n -v --line on example.com yields the following. Anyone know an iptables command to see the port forwarding? Also, it seems to accept all traffic, that's probably bad right? ;] num pkts bytes target prot opt in out source destination 1 14041 1023K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 338 20722 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 419K packets, 425M bytes) num pkts bytes target prot opt in out source destination 1 13711 2824K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 postconf -n results in: alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all local_recipient_maps = mailbox_size_limit = 0 masquerade_domains = mail.example.com mail1.example.com masquerade_exceptions = root maximal_backoff_time = 8000s maximal_queue_lifetime = 7d minimal_backoff_time = 1000s mydestination = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = example.com readme_directory = no recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname SMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf virtual_gid_maps = mysql:/etc/postfix/mysql_gid.cf virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf virtual_uid_maps = mysql:/etc/postfix/mysql_uid.cf

  Read the article

• FFMPEG dropping frames while encoding JPEG sequence at color change

  - by Matt

  I'm trying to put together a slide show using imagemagick and FFMPEG. I use imagemagick to expand a single photo into 30fps video (imagemagick also handles things like putting some text captions on the frames along the way). When I go to let ffmpeg digest it into a video it clips along nicely on the color parts of the video, but when it gets to a black and white section it reports "frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703" and drops every frame of video until it hits something with color. As you can imagine this results in entire photos being removed from the slideshow. Here is my latest dump... ffmpeg -y -r 30 -i "teststream/%06d.jpg" -c:v libx264 -r 30 newffmpeg.mp4 ffmpeg version git-2012-12-10-c3bb333 Copyright (c) 2000-2012 the FFmpeg developers built on Dec 10 2012 22:02:04 with gcc 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) configuration: --enable-gpl --enable-libfaac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 12.100 / 52. 12.100 libavcodec 54. 79.101 / 54. 79.101 libavformat 54. 49.100 / 54. 49.100 libavdevice 54. 3.102 / 54. 3.102 libavfilter 3. 26.101 / 3. 26.101 libswscale 2. 1.103 / 2. 1.103 libswresample 0. 17.102 / 0. 17.102 libpostproc 52. 2.100 / 52. 2.100 Input #0, image2, from 'teststream/%06d.jpg': Duration: 00:12:02.80, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj444p, 720x480 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [libx264 @ 0x3450140] using SAR=1/1 [libx264 @ 0x3450140] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 [libx264 @ 0x3450140] profile High, level 3.0 [libx264 @ 0x3450140] 264 - core 129 r2 1cffe9f - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 lookahead_threads=2 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'newffmpeg.mp4': Metadata: encoder : Lavf54.49.100 Stream #0:0: Video: h264 ([33][0][0][0] / 0x0021), yuvj420p, 720x480 [SAR 1:1 DAR 3:2], q=-1--1, 15360 tbn, 30 tbc Stream mapping: Stream #0:0 - #0:0 (mjpeg - libx264) Press [q] to stop, [?] for help Input stream #0:0 frame changed from size:720x480 fmt:yuvj444p to size:720x480 fmt:yuvj422p Input stream #0:0 frame changed from size:720x480 fmt:yuvj422p to size:720x480 fmt:yuvj444pp=584 frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703 video:5179kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.472425% [libx264 @ 0x3450140] frame I:9 Avg QP:20.10 size: 33933 [libx264 @ 0x3450140] frame P:636 Avg QP:24.12 size: 6737 [libx264 @ 0x3450140] frame B:1385 Avg QP:27.04 size: 514 [libx264 @ 0x3450140] consecutive B-frames: 2.5% 15.2% 13.2% 69.2% [libx264 @ 0x3450140] mb I I16..4: 8.3% 80.3% 11.5% [libx264 @ 0x3450140] mb P I16..4: 1.5% 2.5% 0.2% P16..4: 41.7% 18.0% 10.3% 0.0% 0.0% skip:25.9% [libx264 @ 0x3450140] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 26.6% 0.6% 0.1% direct: 0.2% skip:72.3% L0:35.0% L1:60.3% BI: 4.7% [libx264 @ 0x3450140] 8x8 transform intra:64.1% inter:75.1% [libx264 @ 0x3450140] coded y,uvDC,uvAC intra: 51.6% 78.0% 43.7% inter: 10.6% 14.9% 2.1% [libx264 @ 0x3450140] i16 v,h,dc,p: 29% 19% 6% 46% [libx264 @ 0x3450140] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 23% 15% 17% 5% 9% 10% 7% 8% 6% [libx264 @ 0x3450140] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 31% 18% 11% 5% 9% 10% 6% 6% 4% [libx264 @ 0x3450140] i8c dc,h,v,p: 46% 18% 24% 12% [libx264 @ 0x3450140] Weighted P-Frames: Y:20.1% UV:18.7% [libx264 @ 0x3450140] ref P L0: 59.2% 23.2% 13.1% 4.3% 0.2% [libx264 @ 0x3450140] ref B L0: 88.7% 8.3% 3.0% [libx264 @ 0x3450140] ref B L1: 95.0% 5.0% [libx264 @ 0x3450140] kb/s:626.88 Received signal 2: terminating. One last note: If I remove the -r 30 from the input and output it works flawlessly. I have no idea why the -r 30 is causing it to freak out.

  Read the article

• cannot send mail to postfix /w iptables linux proxy

  - by Juzzam

  I have two separate servers, both running Ubuntu 8.04. Server 1 has the real domain name of our site, let's refer to it as example.com. Server 2 is a mail server I have setup with postfix/courier. The hostname for this server is mail.example.com. I've setup iptables on Server 1 to forward all traffic on port 25 to Server 2. I used this script (except I changed the target ip address and the port from 80 to 25). When I send an email to [email protected] it works. However, when I try to send an email to [email protected] from gmail, I get this error: 550 550 #5.1.0 Address rejected [email protected] (state 14) /var/log/mail.log shows no new lines when this happens. What is strange is that it works with telnet from my local machine. For example: $ telnet example.com 25 220 VO13421.localdomain SMTP Postfix EHLO example.com 250-VO13421.localdomain 250-PIPELINING 250-SIZE 10240000 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN MAIL FROM: [email protected] 250 2.1.0 Ok RCPT TO: [email protected] 250 2.1.5 Ok data 354 Please start mail input. hello user... how have you been? . 250 Mail queued for delivery. quit 221 Closing connection. Good bye. /var/log/mail.log shows success (and the email goes to the maildr): Feb 24 09:47:36 VO13421 postfix/smtpd[2212]: connect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: 65C68120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: 6BDFA120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/cleanup[2216]: 6BDFA120321: message-id= Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: from=, size=395, nrcpt=1 (queue active) Feb 24 09:48:29 VO13421 postfix/virtual[2217]: 6BDFA120321: to=, relay=virtual, delay=0.28, delays=0.25/0.02/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: removed Feb 24 09:48:30 VO13421 postfix/smtpd[2212]: disconnect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] iptables -L -n -v --line on example.com yields the following. Anyone know an iptables command to see the port forwarding? Also, it seems to accept all traffic, that's probably bad right? ;] num pkts bytes target prot opt in out source destination 1 14041 1023K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 338 20722 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 419K packets, 425M bytes) num pkts bytes target prot opt in out source destination 1 13711 2824K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 postconf -n results in: alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all local_recipient_maps = mailbox_size_limit = 0 masquerade_domains = mail.example.com mail1.example.com masquerade_exceptions = root maximal_backoff_time = 8000s maximal_queue_lifetime = 7d minimal_backoff_time = 1000s mydestination = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = example.com readme_directory = no recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname SMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf virtual_gid_maps = mysql:/etc/postfix/mysql_gid.cf virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf virtual_uid_maps = mysql:/etc/postfix/mysql_uid.cf

  Read the article

• Computer not POSTing "randomly"?

  - by smoth190

  I have a custom built PC that is exhibiting some...odd... behavior, something I've never seen before. It was working fine one day, and the next day, it wouldn't start. Seeing as I wanted an upgrade anyway, I purchased a new motherboard that was compatible with all my parts. While replacing the motherboard, I accidentally damaged the CPU. Well, I wanted a new one anyway... so I got a new one. Seeing as I was replacing a ton of parts already, I bought a new PSU because the old one was super loud. When I slapped it all together, it starts up, lights, fans, drives, they all start. But I get no display from the monitor. No beeps, which I believe means it doesn't POST. I figured it was the RAM, because after removing the sound card and graphics card, there was nothing else that I hadn't replaced. When I remove both sticks of RAM, I get a continuous beeping, and according to the mobo handbook, means no RAM. So I think the mobo is functional, or atleast partly. I bought new RAM, but it still didn't work. I tried 3 monitors, with both VGA and DIV. So it's probably not the monitor, either. Now, let me get to the random part. Every 20 or so boots (I should also mention, for about 3 out of 5 boots I have to unplug the PC because it won't powerdown via the button), it will POST and I'll get display. Then, after about 2 or 3 resets, it won't work again. This confuses me so much, because even when I change nothing, it will/will not work. My thought is that maybe it has something to do with the RAM not clearing or something. I also reset the CMOS battery, incase that had anything to do with it, but no eval. I found some weird suggestion online about holding the power button for 30 seconds while it was unplugged. That did nothing, but I didn't expect it would... I've replaced just about the entire computer, and all the parts are compatible. Done about everything I can think of, but nothing has worked. Hopefully someone can help me here. And as I side note: When I do get my computer to boot, it says my hardware has changed and I have to re-activate windows. But it says I have to call Microsoft to do it. So I get this fancy automated voice that asks me to enter in a code into windows, then it asks me "How many computers have you activated with this copy of Windows?". Well, I had it on my computer before I replaced everything, so I said 1. Then he yelled at me for violating my 1-use license. I dunno what's going on there, do I have to re-purchase Windows 7? And they wonder why people pirate software... That's just a bonus question, though. Specs: 8GB of DDR2 RAM (Corsair) AMD CPU (I don't know what GHz or model because I can't find the box... (I think its 4 cores of 2.8Ghz) ASRock A785GM-LE Motherboard

  Read the article

• Issues Converting Plain Text Into Microsoft Word Bulleted Lists

  - by user787832

  I'm a programmer. I hate status reports. I found a way to live with it. While I am working in my IDE ( Visual Slickedit ) I keep a plain text file open in one of the file/buffer tabs. As I finish things I just jot down a quick note into that file. At the end of the week that becomes my weekly status report. Example entries: The Datatables.net plugin runs very slowly in IE 8 with more than 2,000 records. I changed the way I did the server side code to process the data to make less work for the plugin to get decent performance for the IE 8 users. I made a class to wrap data from the new data collection objects into the legacy data holder objects. This will let the new database code be backward compatible with the legacy code until we can replace it. I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site At the end of the month I go back to each weekly *.txt file and paste all of the entries into a MS Word file for a monthly report. I give the monthly report to a liason to the contracting company who has to compile everyone's monthly reports into a single MS Word 2007 document. His problem, soon to be my problem, comes when he highlights my paragraphs like the ones above to put bullets in front of my paragraphs. When he highlights my notes to put bullets in front of them with MS Word 2007, Word rearranges the text a bit and the new line chars/carriage returns stagger the text so the text is no longer in neat chunks. This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site Becomes This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site I tried turning word wrap on in my IDE for the text files I put my status notes in. It just puts some kind of newline character in anyway. Searching/Replacing those chars in the text files has the result of destroying the paragraphs. Once my notes are pasted into MS Word, Word automatically translates them into paragraph breaks. Searching/Replacing them there has similar results. Blank lines separating the notes disappears. One big mess. What I would like is to be able to keep adding my status notes to a text file as I am now, but do something different when I paste the notes into MS Word such that my liason can select the text, hit the bulleting command and NOT have the staggered text as shown above. Any ideas? Thanks much in advance Steve

  Read the article

• can't connect 2 subnets through RRAS 2008 r2

  - by mcdwight6

  I'm working on a project for a networking class. In VMWare Workstation, I have to set up a 2008 r2 server with DHCP reservations for 2 clients on separate subnets and have them ping each other. Here is the output of the route print command: =========================================================================== Interface List 13 ...00 50 56 2a e7 11 ...... Intel(R) PRO/1000 MT Network Connection #3 10 ...00 0c 29 66 88 dd ...... Intel(R) PRO/1000 MT Network Connection 1 ........................... Software Loopback Interface 1 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 14 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 16 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 17 ...00 00 00 00 00 00 00 e0 isatap.{5B8FB196-616F-4168-A020-03E63A309CEC} =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.0.2 266 0.0.0.0 0.0.0.0 On-link 223.6.6.2 266 10.0.0.0 255.0.0.0 On-link 10.0.0.2 266 10.0.0.2 255.255.255.255 On-link 10.0.0.2 266 10.255.255.255 255.255.255.255 On-link 10.0.0.2 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.6.0.0 255.255.0.0 On-link 10.0.0.2 11 128.6.255.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.0 255.255.255.0 On-link 10.0.0.2 11 223.6.6.0 255.255.255.0 On-link 223.6.6.2 266 223.6.6.2 255.255.255.255 On-link 223.6.6.2 266 223.6.6.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.255 255.255.255.255 On-link 223.6.6.2 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.0.2 266 224.0.0.0 240.0.0.0 On-link 223.6.6.2 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.0.2 266 255.255.255.255 255.255.255.255 On-link 223.6.6.2 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.0.2 Default 0.0.0.0 0.0.0.0 128.6.0.2 Default 0.0.0.0 0.0.0.0 223.6.6.2 Default 128.6.0.0 255.255.0.0 10.0.0.2 1 223.6.6.0 255.255.255.0 10.0.0.2 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 1010 2002::/16 On-link 14 266 2002:8006:2::8006:2/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None My problem is that although I have set up both dynamic and persistent static routes in my r2 server, neither of the clients can ping even the NIC outside its own subnet. For example Client A can ping the NIC at 10.0.0.2 and vice-versa, but it gets a general transmit failure when it tries to ping the card at 223.6.6.2, let alone trying to ping the other client. I have completely disabled the firewalls on all machines and anything else I could think of, without success. What am I missing? Edit: Since posting this, I also noticed that the default gateways on my 2 NICs keep getting zeroed out. Does anyone know a fix for this?

  Read the article

• Capistrano + Nginx + Passenger = 403

  - by slimchrisp

  I asked this over at stackoverflow as well, but still haven't received any answers that have helped me to solve this problem. I have spent almost a week at this point trying to solve the issue, and I'm just not making any headway. It seems that this issue is pretty common, but none of the solutions I found online work for me. A buddy of mine is actually creating the same setup, and he is having the same issue. After a few days stuck with the 403 error I started over using this tutorial: http://blog.ninjahideout.com/posts/a-guide-to-a-nginx-passenger-and-rvm-server I had hoped starting from scratch using this tutorial would work, but no dice. Either way, if you view the tutorial you can see what steps I have taken. Here is essentially what I have going on. I have a VPS account on linode.com Server OS is Ubuntu 10.04 Local OS (shouldn't matter, but just so you know) used to deploy with Capistrano is Snow Leopard 10.6.6 I use RVM on the server. Version is 1.2.2 I was previously on ruby-1.9.2-p0 [ i386 ], but per the tutorial listed above I switched to ree-1.8.7-2010.02 [ i386 ]. Running 'which ruby' from the command line verifies that I am using 1.8.7 with the following output: /usr/local/rvm/rubies/ree-1.8.7-2010.02/bin/ruby passenger -v prints the following: Phusion Passenger version 3.0.2 Running 'nginx -v' gives me a message that the command nginx could not be found. The server is definitely there and running as I can use nginx to serve static files, but this could have something to do with my problem. I have two users dealing with the install. root which I used to install everything, and deployer which is a user I created specifically to for deploying my applications My web app directory is in the deployer user's home directory as follows: /home/deployer/webapps/mysite.com/public Per Capistrano default deploy, a symbolic link called current is created in the public folder, and points to /home/deployer/webapps/mysite.com/public/releases/most_current_release I have chmodded the deployer directory recursively to 777 /opt/nginx permissions: rwxr-xr-x /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2 permissions: rwxrwsrwx My nginx config file has gone through just short of eternity variations, but currently looks like this: ================================================================================== worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2; passenger_ruby /usr/local/rvm/bin/passenger_ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { # listen *:80; server_name mysite.com www.mysite.com; root /home/deployer/webapps/mysite.com/public/current; passenger_enabled on; passenger_friendly_error_pages on; access_log logs/mysite.com/server.log; error_log logs/mysite.com/error.log info; error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } } ================================================================================== I bounce nginx, hit the site, and boom. 403, and logs say directory index of /home/deployer... is forbidden As others with a similar problem have said, you can drop an index.html into the public/releases/current_release and it will render. But rails no worky. That's basically it. At this point I have just about completely exhausted every possible solution attempt I can think of. I am a programmer and definitely not a sysadmin, so I am 99% sure this has something to do with permissions that I have hosed, but for the life of me I just can't figure out where. If anyone can help I would really really appreciate it. If there's any specific permission things you want me to check (ie groups/permissions), can you please include the commands to do so as well. Hopefully this will help others in the future who read this post. Let me know if there is any other information I can provide, and thanks in advance!!!

  Read the article

• What *exactly* gets screwed when I kill -9 or pull the power?

  - by Mike

  Set-Up I've been a programmer for quite some time now but I'm still a bit fuzzy on deep, internal stuff. Now. I am well aware that it's not a good idea to either: kill -9 a process (bad) spontaneously pull the power plug on a running computer or server (worse) However, sometimes you just plain have to. Sometimes a process just won't respond no matter what you do, and sometimes a computer just won't respond, no matter what you do. Let's assume a system running Apache 2, MySQL 5, PHP 5, and Python 2.6.5 through mod_wsgi. Note: I'm most interested about Mac OS X here, but an answer that pertains to any UNIX system would help me out. My Concern Each time I have to do either one of these, especially the second, I'm very worried for a period of time that something has been broken. Some file somewhere could be corrupt -- who knows which file? There are over 1,000,000 files on the computer. I'm often using OS X, so I'll run a "Verify Disk" operation through the Disk Utility. It will report no problems, but I'm still concerned about this. What if some configuration file somewhere got screwed up. Or even worse, what if a binary file somewhere is corrupt. Or a script file somewhere is corrupt now. What if some hardware is damaged? What if I don't find out about it until next month, in a critical scenario, when the corruption or damage causes a catastrophe? Or, what if valuable data is already lost? My Hope My hope is that these concerns and worries are unfounded. After all, after doing this many times before, nothing truly bad has happened yet. The worst is I've had to repair some MySQL tables, but I don't seem to have lost any data. But, if my worries are not unfounded, and real damage could happen in either situation 1 or 2, then my hope is that there is a way to detect it and prevent against it. My Question(s) Could this be because modern operating systems are designed to ensure that nothing is lost in these scenarios? Could this be because modern software is designed to ensure that nothing lost? What about modern hardware design? What measures are in place when you pull the power plug? My question is, for both of these scenarios, what exactly can go wrong, and what steps should be taken to fix it? I'm under the impression that one thing that can go wrong is some programs might not have flushed their data to the disk, so any highly recent data that was supposed to be written to the disk (say, a few seconds before the power pull) might be lost. But what about beyond that? And can this very issue of 5-second data loss screw up a system? What about corruption of random files hiding somewhere in the huge forest of files on my hard drives? What about hardware damage? What Would Help Me Most Detailed descriptions about what goes on internally when you either kill -9 a process or pull the power on the whole system. (it seems instant, but can someone slow it down for me?) Explanations of all things that could go wrong in these scenarios, along with (rough of course) probabilities (i.e., this is very unlikely, but this is likely)... Descriptions of measures in place in modern hardware, operating systems, and software, to prevent damage or corruption when these scenarios occur. (to comfort me) Instructions for what to do after a kill -9 or a power pull, beyond "verifying the disk", in order to truly make sure nothing is corrupt or damaged somewhere on the drive. Measures that can be taken to fortify a computer setup so that if something has to be killed or the power has to be pulled, any potential damage is mitigated. Thanks so much!

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• ISP 5 Device Limit ... again

  - by Tommo

  Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

  Read the article

< Previous Page | 676 677 678 679 680 681 682 683 684 685 686 687  | Next Page >