Search Results

Search found 23472 results on 939 pages for 'show'.

Page 687/939 | < Previous Page | 683 684 685 686 687 688 689 690 691 692 693 694  | Next Page >

• Asterisk, IAXModem & Hylafax how-tos?

  - by Brian Postow

  I'm trying to set up Asterisk and IAXModem to send faxes via T38 (Yes, I know I'm swatting a fly with a Buick...) However, since I'm trying to do something so small with a product so large, I'm having trouble finding samples or how-tos that show me how to set this up. I've got all three installed, and I THINK I have my IAXModem config correct. I'm pretty sure that I have Hylafax correct (I've used it with T38Modem) so, I need to know which of the Asterisk samples I need to use, and how to use them. I think I want to use some combination of iax.conf, iaxprov.conf, sip.conf and sip_notify.conf. But I'm not sure where to put them, or what to change... I'm sure that the answer is RTFM, but I'm not sure WHICH M, or where in it to R... thanks. EDIT On a mailing list, someone told me that this actually WON'T WORK because IAX doesn't do T38. So, is there some other way to get Asterisk to work with Hylafax and send T38? I know that Asterisk does T38, the question is how to get the data from Hylafax and back...

  Read the article

• ntpd on Fedora Core 6 with high negative time reset values

  - by Mark White

  The basic problem is we have a FC6 server instance running on a virtual machine, and the system time seems to have been slowly varying until it is now causing a problem. The server runs 24/7 and has been up for 155 days. It has been changed to show GMT, and reports the time as (example) 00:15:15 GMT whereas the actual time is 00:00:00 GMT. This is an offset of 915 seconds. selinux has been changed to 'setenforce 0' for testing and I am running as root. I stop the ntpd service and change the time in System|Administration|Date & Time. The time still shows the same with 'date' in bash. There are no error logs. I change the date with 'date --set' in bash. The response confirms the changed date. I run 'date' and the incorrect date is shown. There are no error logs. I start the ntpd service and /var/log/messages shows success with 'time reset -915.720139s'. The date remains unchanged. ntpq -p shows three three time servers all have offsets of around -915 seconds. I stop ntpd service and try 'ntpd -gqx' and get the same result as above - success, but a large negative time reset. I've tried varying combinations of the above, and a few more settings in System|Administration|Date & Time - no change. I just need to reset the system time to GMT. No offset. But I can't wait for ntpd to slew the time over the next few weeks. Any advice is welcome, cheers! Surely this shouldn't be this difficult... Mark...

  Read the article

• Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

  - by raid question

  I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

  Read the article

• Connecting XRAID to Sunfire via LSI FC card - Drives not showing up

  - by Matthew Watson

  Hi, I've got a Sunfire T1000 machine ( Solaris 10 10/09 s10s_u8wos_08a SPARC ) with a LSI7404EP-LC fibre channel card in it. This is plugged into an XRAID. The system seems to have picked up the card > /usr/platform/`uname -i `/sbin/prtdiag IO Location Type Slot Path Name Model ----------- ----- ---- --------------------------------------------- ------------------------- --------- MB/PCIE0 PCIE 0 /pci@780/fibre-channel fibre-channel MB/PCIE0 PCIE 0 /pci@780/fibre-channel fibre-channel MB/NET0 PCIE MB /pci@7c0/pci@0/network@4 network-pci14e4,1668 MB/NET1 PCIE MB /pci@7c0/pci@0/network@4,1 network-pci14e4,1668 MB/NET2 PCIX MB /pci@7c0/pci@0/pci@8/network@1 network-pci108e,1648 MB/NET3 PCIX MB /pci@7c0/pci@0/pci@8/network@1,1 network-pci108e,1648 MB/PCIX PCIX MB /pci@7c0/pci@0/pci@8/scsi@2 scsi-pci1000,50 LSI,1064 However it doesn't seem to be able to see the xraid attached to it, lsiutil only reports the onboard SAS controller. > /usr/local/bin/lsiutil ~ LSI Logic MPT Configuration Utility, Version 1.62, January 14, 2009 1 MPT Port found Port Name Chip Vendor/Type/Rev MPT Rev Firmware Rev IOC 1. mpt0 LSI Logic SAS1064 A3 105 010a0000 0 Select a device: [1-1 or 0 to quit] I've tried adding the configuration to /kernal/drv/sd.conf and /kernal/drv/ssd.conf as per this thread, however format still cannot see any drives on the xraid. I'm not sure where to go next. Any suggestions? From what I've read..this should pretty much just eb plug it in and they show up in format..

  Read the article

• Cisco router not receiving OSPF updates

  - by WebDevHobo

  Or at least, that's what I think is happening. There doesn't appear to be a debug command for this, or to see if something is in the routing table. I'm testing out this setup in Packet Tracer. I have 3 routers and a webserver From left to right, you have: Webserver - Router1 - Router2 - Router3 Router1 and Router2 can succesfully ping WebServer. Router3 cannot. Router2 has a default gateway set, to send all not-recognized data through its serial interface to Router1. Like this: ip route 0.0.0.0 0.0.0.0 Serial 0/0/1 Serial 0/0/1 being the connection to Router1 Router2 and Router3 have OSPF configured. From their "show run": Router2: router ospf 1 log-adjacency-changes passive-interface Serial0/0/1 network 10.1.1.0 0.0.0.3 area 0 default-information originate ! Router3: router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 passive-interface FastEthernet0/0 ! I was under the assumption that setting default-information originate on Router2 would give Router3 the needed information. What's going wrong here? The interfaces are up. Ip addresses are with mask-range, clock rate is set at correct end. I don't know what else to check.

  Read the article

• Geographically distributed file system with preferred locality

  - by dpb

  Hi All -- I'm building a application that needs to distribute a standard file server across a few sites over a WAN. Basically, each site needs to write a lot of misc files of varying size (some in the 100s MB range, but most small), and the application is written such that collisions aren't a problem. I'd like to have a system set up that meets the following qualifications: Each site can store files in a shared "namespace". That is, all the files would show up in the same filesystem. Each site would not send data over the WAN unless necessary. I.e., there would be local storage on each side of the WAN that would be "merged" into the same logical filesystem. Linux & Free ($$$) is a must. Basically, something like a central NFS share would meet most of the requirements, however it would not allow the locally written data to stay local. All data from remote sides of the WAN would be copied locally all the time. I have looked into Lustre, and have run some successful tests with it, however, it appears to distribute files fairly uniformly across the distributed storage. I have dug through the documentation and have not found anything that automatically will "prefer" local storage over remote storage. Even something that went with the lowest latency storage would be fine. It would work most of the time, which would meet this application's requirements. Any ideas?

  Read the article

• --log-slave-updates is OFF but updates received from master are still logged to slave binary log?

  - by quanta

  MySQL version 5.5.14 According to the document, by the default, slave does not log to its binary log any updates that are received from a master server. Here are my config. on the slave: # egrep 'bin|slave' /etc/my.cnf relay-log=mysqld-relay-bin log-bin = /var/log/mysql/mysql-bin binlog-format=MIXED sync_binlog = 1 log-bin-trust-function-creators = 1 mysql> show global variables like 'log_slave%'; +-------------------+-------+ | Variable_name | Value | +-------------------+-------+ | log_slave_updates | OFF | +-------------------+-------+ 1 row in set (0.01 sec) mysql> select @@log_slave_updates; +---------------------+ | @@log_slave_updates | +---------------------+ | 0 | +---------------------+ 1 row in set (0.00 sec) but slave still logs the updates that are received from a master to its binary logs, let's see the file size: -rw-rw---- 1 mysql mysql 37M Apr 1 01:00 /var/log/mysql/mysql-bin.001256 -rw-rw---- 1 mysql mysql 25M Apr 2 01:00 /var/log/mysql/mysql-bin.001257 -rw-rw---- 1 mysql mysql 46M Apr 3 01:00 /var/log/mysql/mysql-bin.001258 -rw-rw---- 1 mysql mysql 115M Apr 4 01:00 /var/log/mysql/mysql-bin.001259 -rw-rw---- 1 mysql mysql 105M Apr 4 18:54 /var/log/mysql/mysql-bin.001260 and the sample query when reading these binary files with mysqlbinlog utility: #120404 19:08:57 server id 3 end_log_pos 110324763 Query thread_id=382435 exec_time=0 error_code=0 SET TIMESTAMP=1333541337/*!*/; INSERT INTO norep_SplitValues VALUES ( NAME_CONST('cur_string',_utf8'118212' COLLATE 'utf8_general_ci')) /*!*/; # at 110324763 Did I miss something?

  Read the article

• How to start using twill?

  - by brilliant

  How do I start using twill? I have just downloaded it, unpacked it and clicked on the setup .py file in the folder. The black window (terminal) appeared for a moment and vanished. (I do have Python 2.5 installed on my computer - along with SDK from Google App Engine) In the twill documentation section it says: Downloading twill The latest release of twill is twill 0.9, released Thursday, December 27th, 2007; it is available for download at http://darcs.idyll.org/~t/projects/twill-0.9.tar.gz. You can also use Python's easy_install to install or upgrade twill. twill works with Python 2.3 or later. To start using twill, install it and then type twill-sh. At the prompt type: go http://www.slashdot.org/ show showforms showhistory I am not clear from this passage what I am supposed to type (only "twill-sh" or "twill-sh" and all the words under that line) and where (I tried typing it in the command prompt window of my computer - to no avail) Can, anyone, please, help me out here? Thank You in advance.

  Read the article

• Why do most songs in my media collection play twice? - Corrupt media?

  - by Dean

  Problem: Whether I'm playing the media with Rhythmbox on Ubuntu, Winamp on Windows, or my Nokia N95's media player, most of my audio files (OK, maybe only 40%) play twice. Info: I have a 500GB external 2.5" WD HDD, with a 150GB primary FAT32 partition labeled MUSIC. Inside this, I have about 500 folders containing about 10,000 MP3/WMA/M4A/WAV files. I manage the drive using Ubuntu 9.10, and frequently copy data to/from it using RSYNC, or on windows, TotalCopy. The visual output is different in each media player, but it behaves as if the 1 MP3 has the same song on it twice, and as soon as it ends it begins again. Winamp shows that the song goes for 2x as long as it should, The N95's media player shows the progress bar off the right-hand-side of the screen when it begins playing (then jumps back to the left, then continues along...). Rhythmbox doesn't show me how long the song is, nor does the progress bar move along the screen. Plea: It seams to me somewhere along the lines my collection has become corrupt... but where? And how? and please someone tell me I can fix it!! TIA, Dean.

  Read the article

• Software mirroring (RAID1) versus "Fake Raid" for new Windows 7 install

  - by kquinn

  I've just ordered two new hard drives for my main desktop and a copy of Windows 7 Professional 64-bit. I'd like to do a clean install of Win7 onto the new drives (leaving my old XP Pro boot partition around for a while in case something goes disastrously wrong, etc.). I want to have them set up in mirrored (RAID-1) mode. My understanding is that Win7 Pro can do software mirroring, but can I set this up directly at install time? If so, how? Note that I'd like the disk to be split into three partitions (OS/Apps&Data/Bulk data), all of which should be mirrored. Would it be better (more reliable or faster) to use my motherboard's hardware RAID support? My motherboard is an older nVidia nForce 680i SLI, which is not the most stable of motherboards, and I'm not sure how trustworthy its RAID1 configuration might be (or if Win7 could even detect and install onto a hardware-mirrored volume). Also, the performance characteristics of RAID1 are rather different than RAID0 or RAID5, and I'm wondering if Win7's software mirroring might actually be faster than hardware RAID1 (for example, I'm more of a Unix admin when I have to wear the sysadmin hat, and I've had great success deploying ZFS; most hardware RAID1 implementations have to read both disks and compare results to look for data errors, but ZFS can read from only one disk in the mirror and just use the built-in checksum, meaning it can have up to 2x the number of reads in-flight, as long as there's no data corruption). Edit: Okay, my question about whether Windows 7 can do software mirroring has been answered, and it can. I'm still unsure whether Windows software RAID or my motherboard's hardware "fake RAID" function is a better choice, though. Remember, I'm only interested in mirroring -- not the more complicated striping or parity operations that generally show the poor performance of crappy motherboard RAID solutions.

  Read the article

• Is it possible to stop the "Beep" device on all computers in a Windows network?

  - by sharptooth

  On Windows the default behavior it to make an annoying "beep" sound every time Windows things something notable happened. The result is that when someone send a company-wide email via the MS Exchange all computers around my cubicle beep one by one. This is annoying and makes no sense. Luckily beeping can be shut off. Someone has to: open the "Device Manager", select "View - Show hidden devices", find the "Beep" device in "Non-Pug and Play Devices" node, open its properties, go to the "Driver" tab, set "startup type" to "Disabled" and click "Stop". The "Beep" device will stop and no longer produce the useless sound. This solution however requires tracking every computer and then talking to its user which is not very convenient. Device Manager doesn't allow stopping a device on another computer. I'm looking for a solution that can be deployed by the administrators team. We have a domain and the administrators even install the programs company-wide automatically. Are there any means to stop the "Beep" device an all computers in the Windows network with some remote-administration features automatically?

  Read the article

• Unable to logon using terminal server connection

  - by satch

  I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

  Read the article

• I can't connect to my network, except in safe mode

  - by eidylon

  My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

  Read the article

• Windows XP can use a wired network port, but MacBook (OS X) fails on the same port

  - by Dean Hill

  I wired the Cat5 in my house seven years ago. The wired ports have worked fine with both my Windows XP laptop and MacBook. My wireless network also works fine, but I like to use wired occasionally. One of the Cat5 runs wasn't terminated with a jack, so I recently terminated this wire with a port/jack on the wall end and a standard Cat5 plug on the end that plugs into my router. This is the same setup as my other runs. Unfortunately, the MacBook isn't working well with the new wired port. The OS X Network System Preferences show the IP, Subnet, Router, etc., and everything looks fine. A "netstat -ibd" shows no errors or dropped packets. However, when I open a page in Safari, the status says "Contacting 'www.google.com'" and appears to hang. If I wait for a couple minutes, part of the Google page starts to display, but it is still not the full page load. When I use a Windows XP laptop on the same wired port, everything works fine. An internet speed test shows good results and all web pages load fine. A "netstat -e" under Windows shows no errors. I've used a Cat5 tester, and the cable tests fine (wires 1-8 light up in sequence). I've replaced both the port/jack and the connector twice to make sure I wired things correctly. I'd really like this Cat5 to work with the MacBook (and I'm trying to avoid running a new length of cable). Any ideas what the problem could be?

  Read the article

• Debugging "clogged" TCP connections

  - by Nikratio

  I'm having trouble with an internet connection that seems to randomly "freeze" arbitrary tcp connections. The connections stay established, but no data is coming through. When this happens, netstat still shows the connection status as ESTABLISHED on both the local computer: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 53 192.168.0.10:41129 173.255.235.238:143 ESTABLISHED 8219/gnutls-cli on (79.31/13/0) ..and the remote server: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 0 173.255.235.238:143 68.5.174.98:41129 ESTABLISHED 5303/imapd off (0.00/0/0) However, it seems that no data at all is transferred. If I run strace on the local and remote process, both just show a repeating sequence of select calls (with different fds of course), e.g. select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) The internet connection overall does not seem affected, I can still establish new connections to the same service on the same server without any problems. However, the affected local applications seem to be unaware of the problem and just hang. When I look at a packet capture of this connection on the client side, the last thing that happens is that the client transmits some data, then nothing happens for about 1100 seconds, and then several TCP Retransmission requests go out, with intervals increasing from 4 seconds to 130 seconds. No activity is captured after that. After about 10 minutes, the connection on the remote end disappears from the netstat (I wasn't able to catch any intermediate state), but still stays ESTABLISHED on the local end. Finally, after some more minutes, the local application aborts with a timeout and disappears from the local netstat output as well. Does anyone have a suggestion of how I could debug this further to find out where the problem lies and how to fix it? Additionaly and/or as a temporary workaround: is is there some way to globally reduce the timeout on client and/or server to reduce the time before the local application aborts?

  Read the article

• How do I properly configure a ZipInstaller .zic file?

  - by Iszi Rory or Isznti

  As of version 1.20, ZipInstaller is supposed to support the use of a configuration file to customize its installation options. Generally, all the options I want to use are available through the dialog so I really haven't bothered with the configuration file until now. The problem now is that certain tools, such as PsTools from Sysinternals, do not properly show their Product Name to ZipInstaller. ZipInstaller's dialog will let you customize the Start Menu folder and Program Files folder, but that still doesn't change the Product Name that it sees for the software. So, instead of having "PsTools" in my Add/Remove Programs, I get "Sysinternals Software". For some things, the situation is even more confusing. For example, the NIST SP 800-53 Reference Database Application gets installed as "FileMaker Pro Runtime". To rectify this, I've tried to use the aforementioned .zic configuration file. As I understand it, it's a basic INI file you create and put in the root of the ZIP file. ZipInstaller is supposed to read that file, and adjust its parameters accordingly. Mine looks like this: [install] ProductName=NIST_SP_800-53 ProductVersion=1.4.1 CompanyName=NIST Description=NIST_SP_800-53 InstallFolder=%zi.ProgramFiles%\%zi.ProductName% StartMenuFolder=%zi.CompanyName%\%zi.ProductName% I've named it `~zipinst~.zic and placed it in the root of the ZIP file, but when I run ZipInstaller it doesn't seem to recognize any of the information I've given it in the .zic file. What might I be doing wrong here?

  Read the article

• Trouble with IIS SMTP relaying to Gmail

  - by saille

  I appreciate that similar questions have been asked about how to setup SMTP relaying with IIS's virtual SMTP server. However I'm still completely stumped on this problem. Here's the setup: IIS 6.0 SMTP server running on Win2k3 box with a NAT'ed IP. Company uses Gmail for all email services. An app on the box needs to send email, so normally we'd just set the app up to talk to smtp.gmail.com directly, but this app doesn't support TLS. Easy, we just setup a local SMTP relay right? So I thought. What we have done so far: Setup IIS SMTP server to relay to smtp.gmail.com, as per these excellent instructions: http://fmuntean.wordpress.com/2008/10/26/how-to-configure-iis-smtp-server-to-forward-emails-using-a-gmail-account/ The local SMTP relay allows anonymous access. Both the local IP and the loopback IP have been explicitly allowed in the Connection and Relay dialogs. Tried sending email from 2 different apps via the local SMTP server, but failed (the emails end up in the Queue folder, but never get sent). The IIS logs show the conversation with the local app, but zero conversation happening with smtp.gmail.com. The port used by gmail is open outbound, and indeed the apps we have that support TLS can send email directly via smtp.gmail.com, so there is no problem with the network. At this point I changed the smtp settings in IIS SMTP server to use a different external SMTP server and hey-presto, the local apps can send email via local IIS SMTP relay. So smtp.gmail.com fails to work with our IIS SMTP relay, but another 3rd party SMTP service works fine. We need to use smtp.gmail.com, so how to troubleshoot this one?

  Read the article

• Google: "302 Moved" in Firefox

  - by Virtlink

  For some Google search queries executed from the Firefox search bar, or manually by typing in the URL, I get a ''302 Moved'' page. I did a quick virus scan, have checked the hosts file and the plugins and add-ons that are installed in Firefox. Nothing is out of the ordinary. What could be the problem? These URLs (and any URL with google.com, empty and firefox-a in them) show me a 302 Moved page: https://www.google.com/search?q=c%23+empty+array&client=firefox-a https://www.google.com/search?q=empty&client=firefox-a Whereas these URLs work fine: https://www.google.com/search?q=c%23+empty+array (no firefox-a) https://www.google.com/search?q=empty (no firefox-a) https://www.google.com/search?q=c%23+array&client=firefox-a (no empty) https://www.google.nl/search?q=c%23+empty+array&client=firefox-a (no .com) By default Google redirects my queries to their .nl website, and uses HTTPS. I am currently executing a full system virus scan using Security Essentials. My Firefox plugins were up-to-date. No unfamiliar Firefox plugins or add-ons found. Restarting Firefox did not solve the issue. The issue does not occur in Internet Explorer. The hosts file did not contain any unfamiliar entries.

  Read the article

• django : Serving static files through nginx

  - by PlanetUnknown

  I'm using apache+mod_wsgi for django. And all css/js/images are served through nginx. For some odd, reason when others/friends/colleagues try accessing the site, jquery/css is not getting loaded for them, hence the page looks jumbled up. My html files use code like this - <link rel="stylesheet" type="text/css" href="http://x.x.x.x:8000/css/custom.css"/> <script type="text/javascript" src="http://1x.x.x.x:8000/js/custom.js"></script> My nginx configuration in sites-available is like this - server { listen 8000; server_name localhost; access_log /var/log/nginx/aa8000.access.log; error_log /var/log/nginx/aa8000.error.log; location / { index index.html index.htm; } location /static/ { autoindex on; root /opt/aa/webroot/; } } There is a directory /opt/aa/webroot/static/ which have corresponding css & js directories. The odd thing is that the pages show fine when I access them. I have cleared my cache/etc, but the page loads fine for me, from various browsers. Also, I don't see any 404 any error in the nginx log files. Actually the logs for nginx are not getting refreshed at all. I restarted the nginx server using root, is that incorrect ? There is a user www-data defined in the nginx configuration file. Any pointers would be great.

  Read the article

• DEB: "Provides:" field ignored

  - by Creshal

  I need to replace a package with a custom one, which gets its own name (foo-origpackage). To allow it to be used as drop-in replacement, I added the Provides: origpackage line to the control file. apt-cache show foo-origpackage lists the "Provides" entry just fine. However, when I want to install a file depending on origpackage, it fails ("Package origpackage not installed"). Is there some distinction between "real" and virtual packages I'm missing? EDIT: To be precise, what I want to replace is xen-utils-common for Squeeze. My tao-xen-utils-common has the following control file: Source: tao-xen-utils-common Section: kernel Priority: optional Maintainer: Creshal <[email protected]> Build-Depends: debhelper Standards-Version: 3.8.0 Homepage: http://tao.at Package: tao-xen-utils-common Architecture: all Depends: gawk, lsb-base, udev, xenstore-utils, tao-firewall Provides: xen-utils-common Conflicts: xen-utils-common Replaces: xen-utils-common Description: Xen administrative tools - common files (modified) The userspace tools to manage a system virtualized through the Xen virtual machine monitor. Modified for use with TAO Firewall. Installing xen-utils-4.0 fails, however: foo@bar# apt-cache showpkg tao-xen-utils-common Package: tao-xen-utils-common Versions: 4.0.0-1tao1 (/var/lib/apt/lists/repo.tao.at_dists_stable_main_binary-amd64_Packages) (/var/lib/dpkg/status) Description Language: File: /var/lib/apt/lists/repo.tao.at_dists_stable_main_binary-amd64_Packages MD5: 7c2503f563fca13b33b4eb3cbcb3c129 Reverse Depends: tao-firewall,tao-xen-utils-common tao-firewall,tao-xen-utils-common Dependencies: 4.0.0-1tao1 - gawk (0 (null)) lsb-base (0 (null)) udev (0 (null)) xenstore-utils (0 (null)) tao-firewall (0 (null)) xen-utils-common (0 (null)) xen-utils-common (0 (null)) Provides: 4.0.0-1tao1 - xen-utils-common Reverse Provides: foo@bar# apt-get install xen-utils-4.0 Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: xen-utils-common Suggested packages: xen-docs-4.0 The following packages will be REMOVED: tao-xen-utils-common The following NEW packages will be installed: xen-utils-4.0 xen-utils-common Edit:foo@bar# apt-cache policy xen-utils-4.0 xen-utils-4.0: Installed: (none) Candidate: 4.0.1-4 Version table: 4.0.1-4 0 500 http://ftp.at.debian.org/debian/ stable/main amd64 Packages 4.0.1-4 0 500 http://security.debian.org/ stable/updates/main amd64 Packages

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• RRAS Public Address Pool on Windows Server 2008

  - by Art

  I have a Windows 2008 server with two NICs running RRAS and a small public website. It also does NAT for several other PCs on my network and everything works great. I have a block of 5 public static IPs from my ISP, one of which is bound to the public NIC in the Windows 2008 server. I would like to assign one of the remainging 4 public IPs to a machine on my private network. I thought I could do this by going into RRAS, selecting NAT under IPv4 and then adding the public IP address to the address pool and specifying a reservation for the machine I would like to use that address by adding its private ip address. When I do this, the machine I reserved the public IP address for seems to loose all outside network connectivity. I can still ping other PCs on my 192.168.0.* net, but anything outside is no longer reachable. When I remove the reservation, everything seems to work. After setting the reservation and right clicking on the external public interface and selecting 'Show Mappings' I can see outbound requests from my private address with the desired associated private address, however I do not see any inbound requests. What am I doing wrong/missing?

  Read the article

• Very slow connection to xserve via afp or smb

  - by Mhoffman13

  Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

  Read the article

• who has files open on a linux server

  - by Robert

  I have the fairly common task of finding who has files open on our Linux (Ubuntu ) file server in our Windows environment. We use Samba on the network and I use Putty from my workstation to establish a shell window to run bash scripts. I have been using something like this to find what files are open: (this returns a list of process ids with each open file) Robert:$ sudo lsof | grep "/srv/office/some/folder" Then, I follow up with something like this to show who owns the process: (this returns the name of the machine on the network using the IP4 protocol who owns the process) Robert:$ sudo lsof -p 27295 | grep "IPv4" Now I know the windows client who has a file open and can take action from there. As you can tell this is not difficult but time consuming. I would prefer to have a windows application I can run that would just give me what I want. So, I have been thinking about creating some process I can run on Linux that listens on a port and then returns a clean list of all open files with the IP address of the host who has the file open. Then, a small windows client application that can send the request on the port. It seems like this should be a very common need but I can not find anything like this that has been done before. Any suggestions?

  Read the article

• RemoteApp shows no certificate available but RD Session host finds it fine

  - by Scott Chamberlain

  I am trying to set up remote app for a internal domain. I have a Root CA that is trusted my all of the end computers, that cert has signed a wildcard cert I am trying to use for the server. I added the pfx of the wildcard cert to the local machine personal store. From there I can use it fine for signing the RD Session Host session. However when I try to set up the signature for Remote App the certificate does not show up. What do I need to do to get my certificate to be available for for use? UPDATE: The Certificate was generated through the following commands: makecert -pe -n "CN=*.vw.local" -a sha1 -sky signature -ic VetWebCA.cer -iv VetWebCA.pvk -sv VetWebComputerWildcard.pvk VetWebComputerWildcard.cer pvk2pfx -pvk VetWebComputerWildcard.pvk -spc VetWebComputerWildcard.cer -pfx VetWebComputerWildcard.pfx The resultant pfx was added to the machine local store via mmc. Oddly, going in to Powershell if I add the -CodeSigningCert flag to find the wildcard certificate it is excluded from the serch results for Get-Childitem in my Cert:\Local Machine\My path, but if I don't include it it is there.

  Read the article

< Previous Page | 683 684 685 686 687 688 689 690 691 692 693 694  | Next Page >