Search Results

Search found 20140 results on 806 pages for 'remote management'.

Page 695/806 | < Previous Page | 691 692 693 694 695 696 697 698 699 700 701 702  | Next Page >

• Hyper-V: Dedicated NIC for Guests VMs

  - by TheLizardKing

  I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

  Read the article

• OpenSWAN KLIPS not working

  - by bonzi

  I am trying to setup IPSec between 2 VM launched by OpenNebula. I'm using OpenSWAN for that. This is the ipsec.conf file config setup oe=off interfaces=%defaultroute protostack=klips conn host-to-host left=10.141.0.135 # Local IP address connaddrfamily=ipv4 leftrsasigkey=key right=10.141.0.132 # Remote IP address rightrsasigkey=key ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel I'm able to establish the connection with netkey but klips doesnt work. ipsec barf shows #71: ERROR: asynchronous network error report on eth0 (sport=500) for message to 10.141.0.132 port 500, complainant 10.141.0.135: No route to host [errno 113, origin ICMP type 3 code 1 (not authenticated)] Tcpdump shows 22:50:20.592685 IP 10.141.0.132.isakmp > 10.141.0.135.isakmp: isakmp: phase 1 I ident 22:50:25.602182 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:26.602082 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:27.601985 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 ipsec eroute shows 0 10.141.0.135/32 -> 10.141.0.132/32 => %trap What could be the problem?

  Read the article

• Number of routers in small community lock up and require reboot.

  - by Anthony Hiscox

  I live in a small town which has one primary ISP. Lately I have noticed that a number of wireless routers have been locking up and requiring a reboot before allowing any connections. This has affected two of my routers, my work router, and a few others. In all cases wired continued to function as usual. Often wireless clients can see the SSID but simply won't connect. I can only think of a few possibilities and was hoping someone here might be able to point me in the right direction: Our ISP is well known to be flaky, something they are doing is causing this, what that might be I have no clue it as seems to affect the wireless only. There's a power issue in town, given our remote location and reputation for crap electrical, this seems reasonable. Only one router was plugged in to a UPS, and I'm not sure of the quality. There is some bug in all the different firmware for every one of these routers (all different). That doesn't seem reasonable, unless; it's an unknown (or known) exploit or DoS of some sort being launched by a massive team of ninjas hell bent on forcing us all to be tethered to our walls by ethernet cables or; it's just been a coincidence and I'm just paranoid (this has some weight, I mean read 4 again). Anyone else experience similar issues and have some tips?

  Read the article

• Unable to logon using terminal server connection

  - by satch

  I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

  Read the article

• SFTP, Chroot problems on Redhat

  - by Curtis_w

  I'm having problems setting up sftp with a ChrootDirectory. I've done an equivalent setup on other distros, but for some reason I cannot get it to work on a Redhat AMI. The changes to my sshd_config file are: Subsystem sftp internal-sftp Match Group ftponly PasswordAuthentication yes X11Forwarding no ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I have the concerned usere's homes at /home/user, owned by root. After connecting with a user in the ftponly group, I'm dropped into / without permissions for anything, and am unable to do anything. sftp bob@localhost Connecting to localhost... bob@localhost's password: sftp> pwd Remote working directory: / I can connect normally with users not in the ftponly group. openssh version 5.3 I've experimented with different permissions, as well as having users own their own home directory (gives a Write failed: Broken pipe error), and so far, nothing has seemed to work. I'm sure it's a permissions error, or something equally as trivial, but at this point my eyes are beginning to glaze over, and any help would be greatly appreciated. EDIT: James and Madhatter, thanks for clarifying. I was confused by chroot dropping me in /... just didn't think through it properly. I've added the appropriate directories and permissions to get read access. One other key part was enabling write access to chrooted homes: setsebool -P ssh_chroot_rw_homedirs on in order to get write access. I think I'm all set now. Thanks for the help.

  Read the article

• What could cause an 101 Error in WAMP under Windows 7 ?

  - by Brayn

  Hey, I'be been using WAMP for local development for quite a while now but lately I've been getting an Error 101 message when I browse localhost sites. It's possible for this to have appeared after the last WAMP update but I'm not 100% sure on this. If I try again and again, after several page refreshes it works but it's really annoying! The exact error message is: Error 101 (net::ERR_CONNECTION_RESET): Unknown error. This is my configuration: OS: Windows 7 Apache: 2.2.11 PHP: 5.2.9-2 WAMP: 2.0 Also the local scripts connect to a remote MySQL server, they don't use the local MySQL(I don't know if it matters, just though I let you know). I've been looking into the apache logs and I've found the following. It seems that the apache server keeps restarting and I can't figure why: [Wed Oct 14 13:52:30 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:30 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:30 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:30 2009] [notice] Parent: Created child process 6784 [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Child process is running [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Acquired the start mutex. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting 64 worker threads. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting thread to listen on port 80. [Wed Oct 14 13:52:32 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:33 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:33 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:33 2009] [notice] Parent: Created child process 3572 [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Child process is running [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Acquired the start mutex. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting 64 worker threads. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting thread to listen on port 80. Also I've checked Windows Firewall and disabled any other protection that I have on this computer with no improvement. Thanks!

  Read the article

• Server 2008 Print Redirection is failing but only on 16Bit apps

  - by ian

  the main programmer for SoEasyAccounting and we are installing to Server 2008 Standard service pack 1. We install to 2003 with no problems. Important to understand that the print failure only happens in certain circumstances: Note: We use a standard Windows printer selection box to choose the printer Terms used Superbase = a program language that uses ntvdm.exe (Windows process hosting 16 bit apps) Local Printer = printing to a driver loaded onto the Server 2008 Redirect Printer = printing to a automatically established remote printer through an RDP connection Printing Scenarios Server 2008 - 1: Print from notepad to a Redirected Printer = works Server 2008 - 2: Print from Superbase to a Local Printer = works Server 2008 - 3: Print from Superbase to a Redirected Printer = fail Server 2003 - 4: Print from Superbase to a Redirected Printer = works Results The print causes a message in the drivers print queue of Local Downlevel Document, no print though and Superbase recognises that the "Print command failed". Eventvwr has no related issues to the print fail Any help greatly appreciated. So far 2 days spent trying to resolve and here goes my weekend :( unless someone has an idea :) Things I have Tried i. Switching on/off Easy print ii. Loading copy of redirected driver on server

  Read the article

• Administrative shares in Windows 7 Pro not visible

  - by Chris Tybur

  My desktop machine has a clean install of Windows 7 Professional. For some reason the standard administrative shares Admin$, C$, D$, etc are not visible, either in Computer Management - Shared Folders - Shares or via net share. I also have a laptop with a clean install of Windows 7 Professional, and I can see the admin shares in both places. As such, I can map to \\laptop\c$ from the desktop, but I can't map to \\desktop\c$ from the laptop. I pretty much took the defaults during the Windows 7 installations. I've tried adding LocalAccountTokenFilterPolicy to the registry on the desktop, but that didn't work. On the desktop I've also disabled UAC, turned off Windows firewall, removed it from a homegroup, made sure file and printer sharing is turned on, but nothing has worked. There is some subtle difference between the two machines that I can't seem to find. I'm logging into both machines using a local account that is in the Administrators group. Both accounts have the same name and password. I really don't want to have to create a new share for the desktop's C drive, especially since C$ is visible and working on the laptop and therefore I should be able to make it work on the desktop. Any idea why the admin shares would work on one machine and not another? Or why LocalAccountTokenFilterPolicy would fail?

  Read the article

• Celery daemon as a Ubuntu service does not consume tasks while running from terminal does

  - by Guy

  On Ubuntu 11.10, I have to issue python tasks from django using celery. I'm currently testing on the same machine but eventually the celery worker should run on a remote machine. django uses the following settings: BROKER_HOST = "127.0.0.1" BROKER_PORT = 5672 BROKER_VHOST = "/my_vhost" BROKER_USER = "celery" BROKER_PASSWORD = "celery" I can also see my task queued in http://localhost:55672/#/queues the celery daemon uses the following configuration (celeryconfig.py): BROKER_HOST = "127.0.0.1" BROKER_PORT = 5672 BROKER_USER = "celery" BROKER_PASSWORD = "celery" BROKER_VHOST = "/my_vhost" CELERY_RESULT_BACKEND = "amqp" import os import sys sys.path.append(os.getcwd()) CELERY_IMPORTS = ("tasks", ) running celeryd -l info works well and now I want to run it as a service. I've followed the instructions from http://ask.github.com/celery/cookbook/daemonizing.html and now I'm trying to run it using: sudo /etc/init.d/celeryd start But the message is not being consumed, no error in the celery log either. /etc/default/celeryd CELERYD_NODES="w1" CELERYD_CHDIR="/path/to/django/project" CELERYD_OPTS="--time-limit=300 --concurrency=1" CELERY_CONFIG_MODULE="celeryconfig" # %n will be replaced with the nodename. CELERYD_LOG_FILE="/var/log/celery/%n.log" CELERYD_PID_FILE="/var/run/celery/%n.pid" # Workers should run as an unprivileged user. CELERYD_USER="celery" CELERYD_GROUP="celery" I've also created user celery in Ubuntu not sure if its necessary. Any help will be appreciated, Thanks, Guy

  Read the article

• Problem with Outlook 2010 (SMTP AUTH LOGIN)

  - by Filipe YaBa Polido

  **IGNORE THIS QUESTION - SOLVED WITH A PYTHON SCRIPT available at: http://yabahaus.blogspot.com I have to connect one customer Outlook 2010 to a remote server on which I have either no right, neither way to talk to the sysadmin. This is the thing, after installing and reviewing the logs on Wireshark: Outlook Express: HELO machine AUTH LOGIN username base64 encoded password base64 encoded mails go through. Outlook 2010: HELO machine AUTH DIGEST-MD5 response from server Outlook sends just a * AUTH LOGIN password base64 encoded So... I can send mails in the same domain, but can't send outside, it gives me a relay denied message. My point is... Why the h**l Outlook 2010 doesn't send the username AND the password?! It can never login the right way :| With other versions of Outlook it works fine, and with OE works great, it auths and allows to send mail to a different domain. I've googled and nothing worked. I'm pretty sure that I'm not alone with this one. My last resort will be to configure a local proxy/server that relays to the original one :| Any help would be appreciated. Sorry my bad english as is not my natural language. Thanks.

  Read the article

• cannot connect to vpn server (error 721)

  - by callmeblessed

  Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• Hyper-V vss-writer not making current copies

  - by Martinnj

  I'm using diskshadow to backup live Hyper-V machines on a Windows 2008 server. The backup consists of 3 scripts, the first will create the shadow copies and expose them, the second uses robocopy to copy them to a remote location and the third unexposes the shadow copies again. The first script – the one that runs correctly but fails to do what it's supposed to: # DiskShadow script file to backup VM from a Hyper-V host # First, delete any shadow copies of the drives. System Drives needs to be included. Delete Shadows volume C: Delete Shadows volume D: Delete Shadows volume E: #Ensure that shadow copies will persist after DiskShadow has run set context persistent # make sure the path already exists set verbose on begin backup add volume D: alias VirtualDisk add volume C: alias SystemDrive # verify the "Microsoft Hyper-V VSS Writer" writer will be included in the snapshot # NOTE: The writer GUID is exclusive for this install/machine, must be changed on other machines! writer verify {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} create end backup # Backup is exposed as drive X: make sure your drive letter X is not in use Expose %VirtualDisk% X: Exit The next is just a robocopy and then an unexpose. Now, when I run the above script, I get no errors from it, except that the "BITS" writer has been excluded because none of its components are included. That's okay because I really only need the Hyper-V writer. Also I double checked the GUID for the writer, it's correct. During the time when the Hyper-V writer becomes active, 2 things will happen on the guest machines: The Debian/Linux machine will go to a saved state and restore when done, all fine. The Windows guests will "creating vss snapshop-sets" or something similar. Then X: gets exposed and I can copy the .vhd files over. The problem is, for some reason, the VHD files I get over seems to be old copies, they miss files, users and updates that are on the actual machines. I also tried putting the machines in a saved sate manually, didn't change the outcome. I hope someone here has an idea of how to solve this.

  Read the article

• Win Svr 2003 DHCP Bad Addresses

  - by VinceM

  After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

• Quickly set up a Windows Server and automatically install and configure software

  - by Chris

  Yesterday I spent far too much time downloading and installing software on Windows Server 2008. I only had to install a simple server for SQL Server 2008 Express using Microsoft's Web Platform Installer, then configure it to enable remote connections. Everything had to be attended, wasting my time. On a Linux system, this would be trivial to automate, but this is Windows. I do this very rarely, but in the future I would like to make this take as little time as possible. I could do a disc image with everything I installed and configured, but is there a better way? I know nothing of advanced deployment techniques on Windows. Ideally I would like to be able to remotely re-install the OS, or have an unattended install (which I know is possible). Any tips to make the software I need easier to and install and configure with minimal interaction necessary would be helpful. I don't expect everything I asked for to be possible and easy to do. Basically, If any part of it can be done quicker or at least without user input, that's what I'm looking for.

  Read the article

• Server Crash Diagnosis...Are there any 'black box recorder' style programs available.

  - by columbo

  My redhat server is crashing every three weeks or so at 4:15am ish on Sunday mornings. (well it was sundays the last two have been Thursday mornings at 4:15ish) Looking at the logs (mysql, httpd, messages) there are no clues as to why. They just seem to stop. I ran a little script to take memory readings every 15 minutes and it too stops (with normal readings) at this time. The server is remote at a provider so I can only access it via the web. I use Plesk. It appears to be a set job or something that is causing the issue. I can see nothing in crontab. So my question is...has anyone else had this and can offer advice? Failing that. Does any one know of a way to get more detailed logging than that offered by the messages file? I was thinking of a black box style recording program or maybe something as simple as an option somewhere to increase the level of reporting in the messages log. Thanks

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Asus K50I sound issues

  - by MrStatic

  I have an Asus K50IJ (Bestbuy) laptop and have issues with my sound. Speakers themselves work fine but when I plug into the headphone jack it auto mutes the front channel and no sounds comes out of either the speakers or the headphones. If I then unmute the channel I get sound from both the speakers and the headphones. alsamixer shows the Headphone channel as all grayed out. /etc/modprobe.d/alsa-base.conf I have tried snd-hda-intel model="asus-laptop" and snd-hda-intel model="asus" In Sound Preferences I have gone to output and changed the Connector to 'Analog Headphones' that results in no sound from either speakers or headphones. As one forum suggested I tried to comment out blacklist snd_pcsp in the blacklist.conf which resulted in no change. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) Subsystem: Santa Cruz Operation Device 1043 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at fe9f4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel

  Read the article

• Is there a better way to do bonded vlan tagged interfaces with XEN

  - by AJ01

  We have a number of XEN servers all running CentOS or RHEL. The VM's that they run are all required to be on their own VLAN for no other reason than the customer expects them to be. Long story short however, I can't change this right now. We are also required to have bonding enabled on the interfaces. So to accommodat this we enslave eth1 and eth2 to bond0. We then create a seperate interface called bond0.VLANID where VLANID corresponds to the correct vlan; eg ifcfg-bond0.204 DEVICE=bond0.204 BOOTPROTO=static ONBOOT=yes VLAN=yes BRIDGE=xenvlan204 Bridge to XEN As you will see, we eventually have to bridge this out to XEN, and we do this by adding another interface called xenvlan204 (in this instance) which contains; ifcfg-xenvlan204 DEVICE=xenvlan204 BOOTPROTO=none ONBOOT=yes TYPE=bridge XEN Vm Config Finally in our XEN config for each VM, we add vif = [ "bridge=xenvlan204" ] This then allows the vm host to access that particular vlan The Problem We've noticed a few problems with this setup. One being that we currently create the interfaces manually. Which means if we add more vlan enabled interfaces and bridges we usually have to restart xend which is something I'm not so hot about. Also lower level staff have their heads melted by the number of interfaces and the risk of a mistake occurring is high. Secondly, it can take sometime for a host to come up if it has a number of vlan taged interfaces. Thirdly, its just not scaling well on the management aspects The Question Is there a better more flexible way to do this (in particular with Xen that ships with centos 5.3, 5.4 and 5.5 as we have to support all three) that leverages either scripting or other solutions to allow an arbitrary amount of interfaces to be created when a vm is instanced. Your advise and expertise is more that welcomed.

  Read the article

• In solaris, how monitor & auto-respond to critical events

  - by mamcx

  I have a website that randomly fail. Is running in open solaris on joyent. I have a monitoring service that alert me when the site is down, but, I want a way to put a "insider" tool that tell me why that happened. Is because the cpu is too high? Not memory? Which process fail? Is possible to have a backtrace of that? Everything is running on the Solaris Service Management Facility. The webserver is cherokee, the database is mysql and the language is python/django. I want the most simple setup to monitor that & auto-respond , ie: restart the webserver or the django process in case of failure. I prefer a low-overhead tool. I don't need the fancy monitoring that some tools have, no ned graphs or sms alert. Only know what fail, restart it if possible (maybe up to n times), and have a log somewhere when I will check it.

  Read the article

• How to share text, pictures and video to restricted set of users

  - by joaoc

  I want to share pictures and videos of my kid growing up but I don't want it to be open to the public. I just want me and my wife to be able to add material and then share with grandparents and friends who would be given a username/password or some other solution that authenticates them. This content would preferably be available remotely over the internet or downloaded periodically to the allowed viewers computers. The second option most likely means they would have to install a client, which I am not too fond of doing (I would have to ask them to install it, help configure for different platforms, ...) I'm at the start but I would like software that also allows export of the data (if one day I want to migrate to a different solution). Folder sharing I don't know if Windows folder sharing is reliable, robust and safe enough to share over the internet. Dropbox could be a software solution, but it's limited to 2GB and requires receivers to also install and configure software. A folder is just a collection of files, so it would be harder to keep them organized with text describing the pictures/video Email I could email the content every now and then but videos are almost always too big to go as attachments This would also not provide a history of updates to anyone just recently joining in Are there other solutions to achieve this? NOTE: I also thought that software to run a local or remote blog could be an option but we aren't allowed to ask those questions on superuser because one admin doesn't like cloud-computing questions. But if you do think it's the best approach and can suggest a solution, do state it in the answers anyway!

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

< Previous Page | 691 692 693 694 695 696 697 698 699 700 701 702  | Next Page >