Search Results

Search found 670 results on 27 pages for 'g wan'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 7/27 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

  • Slow upload speeds with pfsense virtual appliance

    - by Justin Shin
    I have a pfSense virtual appliance set up in front of a Windows server. The pfSense appliance has been configured with two L2L IPSec VPN sites and not too much else. The appliance has two vNics which both exist on the same VLAN, but one is "WAN" and the other is "LAN." When I run speedtest.net on my Windows server when I have configured it to use a static WAN address and gateway, I get great speeds - maybe around 50 down, 15 up. However, when I configure it with a private IP address, I get similar download speeds but terrible upload speeds - around 2 or 3 Mbps consistently. I used Wireshark to see what gives but there didn't appear to be too much helpful information there, or I just could not find it. Besides the L2L VPNs, other configurations include: Automatic Outbound NAT Virtual P-ARP IP for the Windows Server WAN Firewall rule to allow * to * on RDP WAN Firewall rule to allow * to * (enabled this just for testing... didn't help!) No DHCP or any other services besides IPSec VPN No Errors LAN or WAN No collisions LAN or WAN I would be happy to post the full config file if it would help. I've been scratching my head at this one all day!

    Read the article

  • pfSense router on a LAN with two gateways

    - by JohnCC
    I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

    Read the article

  • Cisco FWSM -> ASA upgrade broke our mail server

    - by Mike Pennington
    We send mail with unicode asian characters to our mail server on the other side of our WAN... immediately after upgrading from a FWSM running 2.3(2) to an ASA5550 running 8.2(5), we saw failures on mail jobs that contained unicode. The symptoms are pretty clear... using the ASA's packet capture utility, we snagged the traffic before and after it left the ASA... access-list PCAP line 1 extended permit tcp any host 192.0.2.25 eq 25 capture pcap_inside type raw-data access-list PCAP buffer 1500000 packet-length 9216 interface inside capture pcap_outside type raw-data access-list PCAP buffer 1500000 packet-length 9216 interface WAN I downloaded the pcaps from the ASA by going to https://<fw_addr>/pcap_inside/pcap and https://<fw_addr>/pcap_outside/pcap... when I looked at them with Wireshark Follow TCP Stream, the inside traffic going into the ASA looks like this EHLO metabike AUTH LOGIN YzFwbUlciXNlck== cZUplCVyXzRw But the same mail leaving the ASA on the outside interface looks like this... EHLO metabike AUTH LOGIN YzFwbUlciXNlck== XXXXXXXXXXXX The XXXX characters are concerning... I fixed the issue by disabling ESMTP inspection: wan-fw1(config)# policy-map global_policy wan-fw1(config-pmap)# class inspection_default wan-fw1(config-pmap-c)# no inspect esmtp wan-fw1(config-pmap-c)# end The $5 question... our old FWSM used SMTP fixup without issues... mail went down at the exact moment that we brought the new ASAs online... what specifically is different about the ASA that it is now breaking this mail? Note: usernames / passwords / app names were changed... don't bother trying to Base64-decode this text.

    Read the article

  • Separate zone exceptions for each view in BIND

    - by Stefan M
    Problem: Separate zones by query source network and return different records for LAN clients compared to WAN clients. I've implemented this at home on a small alix router with Bind 9.4. One view called "lan" and one view called "wan". The "lan" view had just the root.hints file and one zone. The "wan" view had many other zones, including a copy of the one zone from the "lan" view, but with different records. Querying domain1.tld from the LAN would give me local records. Querying domain1.tld from the WAN would give me external records. Querying domain2.tld from the LAN would give me the same records as from the WAN as it only existed in the WAN view. Now I'm trying to re-implement this on a larger scale and suddenly my view is unable to query anything outside itself. This is natural according to the bind-users list and they suggest I copy all my views into my LAN view. I'm hoping someone here has a better solution because that means I'll have to copy, and maintain, thousands of zone files in multiple views. This is unfeasible. My configuration at home resembles this. acl lanClients { 192.168.22.0/24; 127.0.0.1; }; view "intranet" { match-clients { lanClients; }; recursion yes; notify no; // Standard zones // zone "." { type hint; file "etc/root.hint"; }; zone "domain1.tld" { type master; file "intranet/domain1.tld"; }; }; view "internet" { match-clients { !localnets; any; }; recursion no; allow-transfer { slaveDNS; }; include "master.zones"; }; Requests from the LAN for domain1.tld give local records, requests from the WAN give remote records. This works fine both at home and in my new Bind 9.7 on a larger scale. The difference is that at home I have somehow managed to make my LAN get remote records from domains in master.zones, without specifying those zones as duplicates in the "intranet" view. Trying this on a larger scale with Bind 9.7 I get no results at all except for the zones specified in the view. What am I missing? I've tried the same configuration for Bind 9.7.

    Read the article

  • Why we do not use PowerConnect to access PeopleSoft Tree

    - by dylan.wan
    1. It does not allow you to use parameters to the PeopleSoft connect. It may be changed later. However, it was a big issue when we try to address customer issues. 2. It requires EFFDT as an option. It expect that people change the EFFDT using Mapping Editor. How can a business user does that every month? 3. It asks for a Tree Name. Many PeopleSoft tree structure supports multiple trees. Tree is just a header of the hierarchy. Whenever you add a new Tree, you need to create a new mapping!! It does not make sense to use PowerConnect due to the customer demands. All requirements are from customers. We have no choice but stop using it.

    Read the article

  • Cisco 881 losing NAT NVI translation config after reload

    - by MasterRoot24
    This is a weird one, so I'll try to explain in as much detail as I can so I'm giving the whole picture. As I've mentioned in my other questions, I'm in the process of setting up a new Cisco 881 as my WAN router and NAT firewall. I'm facing an issue where NAT NVI rules that I have configured are not enabled after a reload of the router, regardless of the fact that they are present in the startup-config. In order to clarify this a little, here's the relevant section of my current running-config: Router1#show running-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.x 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.x 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.x 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.x 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.x 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.x 993 interface FastEthernet4 993 ...and here's the mappings 'in action': Router1#show ip nat nvi translations | include --- tcp <WAN IP>:25 192.168.1.x:25 --- --- tcp <WAN IP>:80 192.168.1.x:80 --- --- tcp <WAN IP>:143 192.168.1.x:143 --- --- tcp <WAN IP>:443 192.168.1.x:443 --- --- tcp <WAN IP>:587 192.168.1.x:587 --- --- tcp <WAN IP>:993 192.168.1.x:993 --- --- tcp <WAN IP>:1723 192.168.1.x:1723 --- --- ...and here's proof that the mappings are saved to startup-config: Router1#show startup-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.x 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.x 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.x 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.x 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.x 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.x 993 interface FastEthernet4 993 However, look what happens after a reload of the router: Router1#reload Proceed with reload? [confirm]Connection to router closed by remote host. Connection to router closed. $ ssh joe@router Password: Authorized Access only Router1>en Password: Router1#show ip nat nvi translations | include --- Router1# Router1#show ip nat translations | include --- tcp 188.222.181.173:25 192.168.1.2:25 --- --- tcp 188.222.181.173:80 192.168.1.2:80 --- --- tcp 188.222.181.173:143 192.168.1.2:143 --- --- tcp 188.222.181.173:443 192.168.1.2:443 --- --- tcp 188.222.181.173:587 192.168.1.2:587 --- --- tcp 188.222.181.173:993 192.168.1.2:993 --- --- tcp 188.222.181.173:1723 192.168.1.2:1723 --- --- Router1# Here's proof that the running config should have the mappings setup as NVI: Router1#show running-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.2 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.2 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.2 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.2 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.2 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.2 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.2 993 interface FastEthernet4 993 At this point, the mappings are not working (inbound connections from WAN on the HTTP/IMAP fail). I presume that this is because my interfaces are using ip nat enable for use with NVI mappings, instead of ip nat inside/outside. So, I re-apply the mappings: Router1#configure ter Router1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router1(config)#ip nat source static tcp 192.168.1.2 1723 interface FastEthernet4 1723 Router1(config)#ip nat source static tcp 192.168.1.2 80 interface FastEthernet4 80 Router1(config)#ip nat source static tcp 192.168.1.2 443 interface FastEthernet4 443 Router1(config)#ip nat source static tcp 192.168.1.2 25 interface FastEthernet4 25 Router1(config)#ip nat source static tcp 192.168.1.2 587 interface FastEthernet4 587 Router1(config)#ip nat source static tcp 192.168.1.2 143 interface FastEthernet4 143 Router1(config)#ip nat source static tcp 192.168.1.2 993 interface FastEthernet4 993 Router1(config)#end ... then they show up correctly: Router1#show ip nat nvi translations | include --- tcp 188.222.181.173:25 192.168.1.2:25 --- --- tcp 188.222.181.173:80 192.168.1.2:80 --- --- tcp 188.222.181.173:143 192.168.1.2:143 --- --- tcp 188.222.181.173:443 192.168.1.2:443 --- --- tcp 188.222.181.173:587 192.168.1.2:587 --- --- tcp 188.222.181.173:993 192.168.1.2:993 --- --- tcp 188.222.181.173:1723 192.168.1.2:1723 --- --- Router1# Router1#show ip nat translations | include --- Router1# ... furthermore, now from both WAN and LAN, the services mapped above now work until the next reload. All of the above is required every time I have to reload the router (which is all too often at the moment :-( ). Here's my full current config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip access-group 101 in ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 access-list 101 permit udp 193.x.x.0 0.0.0.255 any eq 5060 access-list 101 deny udp any any eq 5060 access-list 101 permit ip any any ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end I'd appreciate it greatly if anyone can help me find out why these mappings are not setup correctly using the saved config after a reload.

    Read the article

  • How do I create in Xcode an iPhone project specifying at project creation time the SDK version I wan

    - by unforgiven
    With the latest Xcode and SDK 3.0 beta when you create a new iPhone project, Xcode creates an SDK 3.0 project. If I want to revert to SDK 2.2.1 after the project has been created, I need to change something in the generated source code files since some of the APIs have changed. Is there a simple way to specify at project creation time the SDK I want to use explicitly? Thank you in advance

    Read the article

  • Wireless clients have no route to ethernet clients in OpenWrt router

    - by superjoe30
    I'm using OpenWrt Kamikaze 8.09 on a Linksys WRT54g v1.1 router. I just flashed it with default settings and got everything working, except my wireless laptop cannot ping my desktop which is wired to the router. What can I do to fix this? (My desktop can ping other desktops wired to the router) My routing table: config 'defaults' option 'syn_flood' '1' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'lan' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'wan' option 'input' 'REJECT' option 'output' 'ACCEPT' option 'forward' 'REJECT' option 'masq' '1' config 'forwarding' option 'src' 'lan' option 'dest' 'wan' option 'mtu_fix' '1' config 'redirect' option 'src' 'wan' option '_name' 'ssh' option 'proto' 'tcp' option 'src_dport' '22' option 'dest_ip' '192.168.1.100' option 'dest_port' '22' config 'redirect' option 'src' 'wan' option '_name' 'http' option 'proto' 'tcp' option 'src_dport' '8888' option 'dest_ip' '192.168.1.100' option 'dest_port' '8888'

    Read the article

  • Problems with MGCP proxy creation

    - by Popof
    Hi, I'm trying to bypass my ISP router with my FreeBSD server (I've an optical connection so I've a RJ45 used to connect the box to WAN) Internet and TV are working fine (Using igmpproxy to forward TV stream) but I've a problem with phone. ISP's box is connected to the server which gives it a LAN address. The problem is that when the box builds MGCP packets (and especially SDP ones) it uses its LAN address. So I've think of writing an UDP proxy to handle MGCP and SDP packets in order to replace LAN address with server WAN address and then forward packet to WAN. Before starting coding I've captured stream packets using my server as a bridge between WAN connection and the ISP's box. And, in order to see if my solution is viable, I've tried to send those packets to the box using nemesis. I tried to send a packet (found in capture) containing an endpoint audit: AUEP 1447 aaln/[email protected] MGCP 1.0 F: A In the wireshark capture the box replied: 200 1447 OK A: a:PCMU;PCMA;G726-16;G726-24;G726-32;G726-40;G.723.1-5.3;G.723.1-6.3;G729;TELEPHONE-EVENT, fmtp:"TELEPHONE-EVENT 0-15,144,149,159", p:10-30, b:4-40, e:on, t:00, s:on, v:L;M;G;D, m:sendonly;recvonly;sendrecv;inactive;confrnce;replcate;netwtest;netwloop, dq-gi But when I use nemesis, I got an ICMP error: Port unreachable (Type 3, Code 3). To build this packet, WAN source address of the capture is replaced with my server LAN address, using the mgcp-callagent port (2727) and the packet is sent to the LAN address of the box at mgcp-gateway port (2427). The command I use is nemesis udp -S 192.168.2.1 -D 192.168.2.2 -x 2727 -y 2427 -P packet_to_send. I also tried an UDP scan to the box on callagent and gateway port: PORT STATE SERVICE 2727/udp open|filtered unknown 2427/udp closed unknown I found those results a little bit strange because it should be the 2427 port opened, as it was in capture. Internet Protocol, Src: <ISP MGCP Server>, Dst: <My WAN Address> User Datagram Protocol, Src Port: mgcp-callagent (2727), Dst Port: mgcp-gateway (2427) Does someone has any idea about how having my box responding to my requests ? Thanks in advance and sorry for my english.

    Read the article

  • Wireless Access Point stopped working

    - by Alex Pritchard
    I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

    Read the article

  • Iptables: masquarading and routing

    - by nixnotwin
    I have a WAN router which is linked to isp over a /30 WAN subnet. But it also servers as a router to a /29 local public WAN subnet which is connected to few of my servers. The traffic from /29 gets routed to ISP via /30 subnet. For a wired reason I want to masqarade (NAT) the interface which has /30 ip. So the interface with /30 ip should appear as masquaraded for my 192.168.1.0/24 network and it also should act as a normal non-NAT router for my WAN public subnet /29. Can this be done with iptables on a Linux machine?

    Read the article

  • Routing between two networks on linux?

    - by gGololicic
    I got stuck with one problem I cant find solution. I have linux pc with two NIC. first nic (eth1) is connected to public ip (probably switch or whatever, doesnt really mater) so eth1 is connected to wan and another eth0 that I connected to switch and make it a lan nic. configuration: eth1 ip address 88.200.1xx.xxx //xxx's are cuz of security reasons eth0 ip address 192.168.1.1 wan ------ [eth1 (linux PC) eth0]<----[switch]<---- [eth1 (PC1)] Now I want to connect this two networks, so PC1 can access linux PC and wan. I think I know how to do it but I cant confiugre it right. This is what I tried: I turend on ip forwarding (for sure) I set eth1 default gw to the right ip on the wan I tried to set eth0 default gw to the same ip (but i couldnt) What or how can I do this, I was trying with linux route command, but I got stuck. Please help.

    Read the article

  • Can a consumer wireless router act as both a wireless client and access point?

    - by glibdud
    I'm going to be moving in the future, and integrating my home network into that of my landlord. I wish to maintain an isolated network while using his internet connection, so I'm planning on cascading my router off of his (WAN-to-LAN type configuration). Unfortunately, it looks like it might not be feasible to run a wire between the two. Therefore, I'd like to send my WAN connection over WiFi to his router. At my disposal, I have a WRT54GL (running Shibby's Tomato mod), and I just bought an Asus RT-N66U (I can be flexible with the firmware). My first thought was to set up the WRT as a wireless bridge, then run a wire between that and the N66U's WAN port. I'm reasonably sure I could make that work, but can I eliminate the WRT from the equation altogether? Can the N66U connect to the landlord's WiFi as a client, effectively using that as the WAN port, while simultaneously providing wireless access to my devices on an altogether different WLAN?

    Read the article

  • Why Remote Desktop Sessions show client internal IP address? [closed]

    - by Varp
    I have Windows Server 2008 r2 with static ip address on WAN interface. I connecting to the server from home from my laptop. Laptop at home is behind nat box. When i connecting to the server from home in Remote Desktop Session Manager i see in client status dialog a local ip address of client behind the nat box not WAN ip address of nat box. I suppose i must see the WAN ip address of the nat box in Remote Desktop Session Manager, isnt it?

    Read the article

  • Port forwarding DD-WRT

    - by Pawel
    Hi, I'am runing locally service on port 81 (192.168.1.101) I would like to access server from outside MY.WAN.IP.ADDR:81. Everything is working fine on my local network, However can't access it from outside. Below iptables rules on the router. I am using dd-wrt and asus rt-n16 (everything is setup through standard port range forwarding in dd-wrt ) It might be something obvious, but I don't have any experience with routing. Any help will be really appreciated. Thanks. #iptables -t nat -vnL Chain PREROUTING (policy ACCEPT 1285 packets, 148K bytes) pkts bytes target prot opt in out source destination 3 252 DNAT icmp -- * * 0.0.0.0/0 MY.WAN.IP.ADDR to:192.168.1.1 5 300 DNAT tcp -- * * 0.0.0.0/0 MY.WAN.IP.ADDR tcp dpt:81 to:192.168.1.101 0 0 DNAT udp -- * * 0.0.0.0/0 MY.WAN.IP.ADDR udp dpt:81 to:192.168.1.101 298 39375 TRIGGER 0 -- * * 0.0.0.0/0 MY.WAN.IP.ADDR TRIGGER type:dnat match:0 relate:0 Chain POSTROUTING (policy ACCEPT 7 packets, 433 bytes) pkts bytes target prot opt in out source destination 747 91318 SNAT 0 -- * vlan2 0.0.0.0/0 0.0.0.0/0 to:MY.WAN.IP.ADDR 0 0 RETURN 0 -- * br0 0.0.0.0/0 0.0.0.0/0 PKTTYPE = broadcast Chain OUTPUT (policy ACCEPT 86 packets, 5673 bytes) pkts bytes target prot opt in out source destination # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination DROP tcp -- anywhere anywhere tcp dpt:webcache DROP tcp -- anywhere anywhere tcp dpt:www DROP tcp -- anywhere anywhere tcp dpt:https DROP tcp -- anywhere anywhere tcp dpt:69 DROP tcp -- anywhere anywhere tcp dpt:ssh DROP tcp -- anywhere anywhere tcp dpt:ssh DROP tcp -- anywhere anywhere tcp dpt:telnet DROP tcp -- anywhere anywhere tcp dpt:telnet Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT 0 -- anywhere anywhere TCPMSS tcp -- anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU lan2wan 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED logaccept tcp -- anywhere pawel-ubuntu tcp dpt:81 logaccept udp -- anywhere pawel-ubuntu udp dpt:81 TRIGGER 0 -- anywhere anywhere TRIGGER type:in match:0 relate:0 trigger_out 0 -- anywhere anywhere logaccept 0 -- anywhere anywhere state NEW Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain advgrp_1 (0 references) target prot opt source destination Chain advgrp_10 (0 references) target prot opt source destination Chain advgrp_2 (0 references) target prot opt source destination Chain advgrp_3 (0 references) target prot opt source destination Chain advgrp_4 (0 references) target prot opt source destination Chain advgrp_5 (0 references) target prot opt source destination Chain advgrp_6 (0 references) target prot opt source destination Chain advgrp_7 (0 references) target prot opt source destination Chain advgrp_8 (0 references) target prot opt source destination Chain advgrp_9 (0 references) target prot opt source destination Chain grp_1 (0 references) target prot opt source destination Chain grp_10 (0 references) target prot opt source destination Chain grp_2 (0 references) target prot opt source destination Chain grp_3 (0 references) target prot opt source destination Chain grp_4 (0 references) target prot opt source destination Chain grp_5 (0 references) target prot opt source destination Chain grp_6 (0 references) target prot opt source destination Chain grp_7 (0 references) target prot opt source destination Chain grp_8 (0 references) target prot opt source destination Chain grp_9 (0 references) target prot opt source destination Chain lan2wan (1 references) target prot opt source destination Chain logaccept (3 references) target prot opt source destination ACCEPT 0 -- anywhere anywhere Chain logdrop (0 references) target prot opt source destination DROP 0 -- anywhere anywhere Chain logreject (0 references) target prot opt source destination REJECT tcp -- anywhere anywhere tcp reject-with tcp-reset Chain trigger_out (1 references) target prot opt source destination #iptables -vnL FORWARD Chain FORWARD (policy ACCEPT 130 packets, 5327 bytes) pkts bytes target prot opt in out source destination 15 900 ACCEPT 0 -- br0 br0 0.0.0.0/0 0.0.0.0/0 390 20708 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 182K 130M lan2wan 0 -- * * 0.0.0.0/0 0.0.0.0/0 179K 129M ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 logaccept tcp -- * * 0.0.0.0/0 192.168.1.101 tcp dpt:81 0 0 logaccept udp -- * * 0.0.0.0/0 192.168.1.101 udp dpt:81 0 0 TRIGGER 0 -- vlan2 br0 0.0.0.0/0 0.0.0.0/0 TRIGGER type:in match:0 relate:0 2612 768K trigger_out 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 2482 762K logaccept 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 state NEW

    Read the article

  • Why won't vyatta allow SMTP through my firewall?

    - by Solignis
    I am setting up a vyatta router on VMware ESXi, But I see to have hit a major snag, I could not get my firewall and NAT to work correctly. I am not sure what was wrong with NAT but it "seems" to be working now. But the firewall is not allowing traffic from my WAN interface (eth0) to my LAN (eth1). I can confirm its the firewall because I disabled all firewall rules and everything worked with just NAT. If put the firewalls (WAN and LAN) back in place nothing can get through to port 25. I am not really sure what the issue could be I am using pretty basic firewall rules, I wrote the rules while looking at the vyatta docs so unless there is something odd with the documentation they "should" be working. Here is my NAT rules so far; vyatta@gateway# show service nat rule 20 { description "Zimbra SNAT #1" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.17 } type source } rule 21 { description "Zimbra SMTP #1" destination { address 74.XXX.XXX.XXX port 25 } inbound-interface eth0 inside-address { address 10.0.0.17 } protocol tcp type destination } rule 100 { description "Default LAN -> WAN" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.0/24 } type source } Then here is my firewall rules, this is where I believe the problem is. vyatta@gateway# show firewall all-ping enable broadcast-ping disable conntrack-expect-table-size 4096 conntrack-hash-size 4096 conntrack-table-size 32768 conntrack-tcp-loose enable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name LAN_in { rule 100 { action accept description "Default LAN -> any" protocol all source { address 10.0.0.0/24 } } } name LAN_out { } name LOCAL { rule 100 { action accept state { established enable } } } name WAN_in { rule 20 { action accept description "Allow SMTP connections to MX01" destination { address 74.XXX.XXX.XXX port 25 } protocol tcp } rule 100 { action accept description "Allow established connections back through" state { established enable } } } name WAN_out { } receive-redirects disable send-redirects enable source-validation disable syn-cookies enable SIDENOTE To test for open ports I have using this website, http://www.yougetsignal.com/tools/open-ports/, it showed port 25 as open without the firewall rules and closed with the firewall rules. UPDATE Just to see if the firewall was working properly I made a rule to block SSH from the WAN interface. When I checked for port 22 on my primary WAN address it said it was still open even though I outright blocked the port. Here is the rule I used; rule 21 { action reject destination { address 74.219.80.163 port 22 } protocol tcp } So now I am convinced either I am doing something wrong or the firewall is not working like it should.

    Read the article

  • Powershell Win32_NetworkAdapterConfiguration Not "seeing" PPP Adapter

    - by Ben
    I am trying to get the IP of a PPP VPN network connection, but Win32_NetworkAdapterConfiguration does not seem to "see" it. If I interrogate all adapters using my script, it will see everything but the PPP VPN adapter. Is there a specific filter or something I need to enable, or do I need a different class? My Script: $colItems = Get-wmiobject Win32_NetworkAdapterConfiguration foreach ($objItem in $colItems) { Write-Host Description: $objItem.Description Write-Host IP Address: $objItem.IPAddress Write-Host "" } Script Output: Description: WAN Miniport (SSTP) IP Address: Description: WAN Miniport (IKEv2) IP Address: Description: WAN Miniport (L2TP) IP Address: Description: WAN Miniport (PPTP) IP Address: Description: WAN Miniport (PPPOE) IP Address: Description: WAN Miniport (IPv6) IP Address: Description: WAN Miniport (Network Monitor) IP Address: Description: Intel(R) PRO/Wireless 3945ABG Network Connection IP Address: 192.168.2.5 Description: WAN Miniport (IP) IP Address: ipconfig /all output: PPP adapter My VPN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : My VPN Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.1.8.12(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 DNS Servers . . . . . . . . . . . : 10.1.1.3 10.1.1.2 Primary WINS Server . . . . . . . : 10.1.1.2 Secondary WINS Server . . . . . . : 10.1.1.3 NetBIOS over Tcpip. . . . . . . . : Enabled Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Belkin Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Network Connection Physical Address. . . . . . . . . : 00-3F-3C-22-22-22 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.2.5(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 25 May 2010 20:33:19 Lease Expires . . . . . . . . . . : 22 May 2020 20:33:17 Default Gateway . . . . . . . . . : 192.168.2.1 DHCP Server . . . . . . . . . . . : 192.168.2.1 DNS Servers . . . . . . . . . . . : 192.168.2.1 NetBIOS over Tcpip. . . . . . . . : Enabled Thanks in advance, Ben

    Read the article

  • NATing IPv4 while routing IPv6

    - by Hugo
    I've the following setup: client(s) <---> (eth0) router (eth1) <---> wan I have a static IPv4 address and a /48 IPv6 address block. I need to connect all the clients to (wan). Each client will have it's own public IPv6. Meanwhile, I need to NAT those same clients over to (wan). Everything IPv4-related and the NAT are working fine. The IPv6 communication to/from (eth0)<-(clients) works fine, as does the IPv6 communication from (eth1)<-(wan) works fine. To provide IPv6 to all my clients, I've thought of too choices: Having the router as a gateway, which different IP on each interface. This sounds like I need to tell my ISP to route the entire block through that single IP, so it's not really an option. Transparently pass IPv6 packets to/from eth0<-eth1, so all clients can communicate with the upstream gateway (I would actually have a switch here if it weren't for the need to remain IPv4 compatible). So, since I've opted for the second choice, I'm in doubt: How can I pass all IPv6 traffic from eth0 to eth1 transparently? What I need is a level 3 bridge, but linux's bridgeutils create a level 2 bridge (which would bridge ipv4 as well, and I can't have that). This is a DD-WRT device, but it's pretty much an embeded linux, so most suggestions that would work on linux are welcome. Thanks.

    Read the article

  • Geographically distributed file system with preferred locality

    - by dpb
    Hi All -- I'm building a application that needs to distribute a standard file server across a few sites over a WAN. Basically, each site needs to write a lot of misc files of varying size (some in the 100s MB range, but most small), and the application is written such that collisions aren't a problem. I'd like to have a system set up that meets the following qualifications: Each site can store files in a shared "namespace". That is, all the files would show up in the same filesystem. Each site would not send data over the WAN unless necessary. I.e., there would be local storage on each side of the WAN that would be "merged" into the same logical filesystem. Linux & Free ($$$) is a must. Basically, something like a central NFS share would meet most of the requirements, however it would not allow the locally written data to stay local. All data from remote sides of the WAN would be copied locally all the time. I have looked into Lustre, and have run some successful tests with it, however, it appears to distribute files fairly uniformly across the distributed storage. I have dug through the documentation and have not found anything that automatically will "prefer" local storage over remote storage. Even something that went with the lowest latency storage would be fine. It would work most of the time, which would meet this application's requirements. Any ideas?

    Read the article

  • Sonicwall TZ210 - Set up public wifi on separate subnet & interface

    - by thomasjbarrett
    I want to set up a public wifi by connecting another router to the X6 interface, and put it on a separate subnet (192.168.10.0/24) & in the DMZ Zone to keep it away from the regular LAN. I believe I have the network settings correct: the router has acquired the IP and DNS information from the TZ210, and the TZ210 shows it as an active DHCP lease. X6 is in the DMZ. I now have a routing/NAT/firewall problem, since I can't get any traffic to travel from the subnet to the internet. I can't get to any external websites and can't ping the TZ210 from the subnet. X0 is the regular LAN, and X1 is the WAN. Looking for any tips or tutorials on this. Here's my current relevant rules: Routing Source: X6 Subnet Destination: Any Service: Any Gateway: Default Gateway Interface: X6 Source: Any Destination: X6 Subnet Service: Any Gateway: 0.0.0.0 Interface: X6 NAT Policies Source Original: Any Translated: WAN IP Destination Original: Any Translated: Original Inbound: X6 Outbound: X1 Source Original: Any Translated: U0 IP Destination Original: Any Translated: Original Inbound: X6 Outbound: U0 Firewall DMZ LAN : Deny All DMZ WAN : Allow All LAN DMZ : Allow All WAN DMZ : Allow All

    Read the article

  • NAT confusion regarding cisco ASA5510

    - by LonelyLonelyNetworkN00b
    I'm setting up my first cisco firewalls. A little information first:I have two asa5510 setup in a working active/standby pair. From my ISP i have two public subnets. A /29 and a /26. On my DMZ interface i have the /26 configured. On my WAN Interface i have configured the /29 IPs. My isp routes the /26 via the /29 primary IP. I'm running ASA 8.2. I've turned NAT-Control off, because i don't want to use nat for for other than some internal interfaces. In essence i don't want to use NAT unless i specify it. I have a internal interface with the network of 192.168.100.0/24. I've tried setting up nat limke this: nat (inside) 1 192.168.100.0 255.255.255.0 global (WAN) 1 interface I was under the impression that this would let connections that was going from 192.168.100.0/24 and out the WAN interface to be Port-Address-translated. I'm not getting this to work for some reason. Inside interface has security level of 100, and wan has security level of 0.

    Read the article

  • Port Forwarding failing only to Ubuntu servers from Draytek router

    - by Rufinus
    I know this is a kinda unusal question, but Draytek support (..which is very eager to solve the issue) seems to reach its limits. Scenario: Draytek Vigor Multiwan router with current firmware. Multiple WAN IP Aliases on one of the wan ports DMZ (or port forwarding doesnt matter) from wan ip alias to internal host currently i have two internal hosts: 192.168.0.51 (Ubuntu) 192.168.0.53 (Debian) both should be accessible from outside via one of the wan ip aliases. both are accessible with their internal ip's at all times (!) If the router gots restartet, both external ips are forwarding to its internal hosts. But after a few minutes up to 2 hours, the ubuntu host is no longer reachable via its external interface. The debian hosts on the other hand is reachable. In what does ubuntu differs from debian ? I know at least of one user with the exact same problem. see http://ubuntuforums.org/showthread.php?p=10994279 Any ideas ? TIA EDIT: via ping diagnostics directly on vigor, 192.168.0.53 is pingable, 192.168.0.51 is not. but both hosts are perfectly reachable from anywhere inside the network. if i restart ubuntu networking it works again for a short time.... i'm out of ideas.. EDIT 2: after further investigation, i noticed a ping from .51 to the network (or a host in the internet) is enough to make the port-forwarding working again. So i will add an Cronjob as a "keep-alive" ping. This will solve the problem, but the reason for this behaivor is still in the dark. Thanks to all commentors.

    Read the article

  • Access server using IP on another interface

    - by Markos
    I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

    Read the article

  • Cisco access-list confusion

    - by LonelyLonelyNetworkN00b
    I'm having troubles implementing access-lists on my asa 5510 (8.2) in a way that makes sense for me. I have one access-list for every interface i have on the device. The access-lists are added to the interface via the access-group command. let's say I have these access-lists access-group WAN_access_in in interface WAN access-group INTERNAL_access_in in interface INTERNAL access-group Production_access_in in interface PRODUCTION WAN has security level 0, Internal Security level 100, Production has security level 50. What i want to do is have an easy way to poke holes from Production to Internal. This seams to be pretty easy, but then the whole notion of security levels doesn't seam to matter any more. I then can't exit out the WAN interface. I would need to add an ANY ANY access-list, which in turn opens access completely for the INTERNAL net. I could solve this by issuing explicit DENY ACEs for my internal net, but that sounds like quite the hassle. How is this done in practice? In iptables i would use a logic of something like this. If source equals production-subnet and outgoing interface equals WAN. ACCEPT.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >