Search Results

Search found 12705 results on 509 pages for 'ip routing'.

Page 7/509 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• Public/Private IP address

  - by crn

  We have several websites (with several public IP addresses) running on a web server. In IIS, the IP address are internal IP addresses (192.168.xxx.xxx). How do I figure out which public IP address matches which internal IP address? My goal is to change some public IP addresses. The particular web server is running IIS 6 on a Windows 2003 Server. Thanks, in advance, for your help!

  Read the article

• Set Valid IP On Vmware Vm's Help Please

  - by Shahin At

  I Have a VPS.And i on my vps installed vmware workstation version 9.now i have 3 valid ip's: XXX.152.193.66 XXX.152.193.101 XXX.152.193.103 Gateway: XXX.152.193.65 now tow ip's set in host and i want to 1 ip set on vm. network vm is bridge and set ip on vm but this ip from out of internal network not ping and in vm not ping to gateway. What can I do to solve this problem? my ip is unassigned and only set on vm and use bridge network mode.and gw,mask,dns is set.but not ping. i set this ip on host and without problems is worked, But I do not know why on vm not worked. my host OS Is Windows Server 2003 and firewall is off and RRAs(routing and remote access) For VPN service is Enable. Do not host or virtual machines to create a IP route?

  Read the article

• Route using certain IP address

  - by spa

  I have a server with two public IPs. Both IPs are added to eth0 using ip addr add. Now I'd like to contact a server which uses IP address filtering. Only requests are allowed which use the second IP address. Is there are way to set this up using the standard route command in Linux? I guess that's not the case. So the only solution I see right now: Setup a virtual device let's say eth0:0 and bind the second IP address to it. Then I can reference the device in the route command. Edit: I can't use the second IP as primary one easily as this IP is used as failover IP.

  Read the article

• Port listening on localhost:8000 but not on ip:8000

  - by Marionette

  Hello I'm running a web application on port 8000. When I access it from the host server localhost:8000 it responds ok, 127.0.0.1:8000 also works, but 192.168.1.7:8000 does not work. 192.168.1.7 is the ip of my server. Also if i try to go to another web application running on port 80 it works 192.168.1.7 I enabled ufw firewall and set ufw default allow. I am using ubuntu server 12.04 Any suggestions on why I can't get to my app on port 8000 using the ip-address:8000? Thanks in advance!

  Read the article

• 503 Error After Microsoft Request Routing Is Installed - 32 bit 64 bit madness

  - by KenB

  I have a requirement to install the Microsoft Request Routing component for IIS 7.5 running on a Windows 2008 R2 SP1 64Bit machine. After installing Microsoft Request Routing via the Web Platform installer our ASP.NET 4.0 application gets a "HTTP Error 503. The service is unavailable." The Windows event log error details says: The Module DLL 'C:\Program Files\IIS\Application Request Routing\requestRouter.dll' could not be loaded due to a configuration problem. The current configuration only supports loading images built for a AMD64 processor architecture. The data field contains the error number. To learn more about this issue, including how to troubleshooting this kind of processor architecture mismatch error, see http://go.microsoft.com/fwlink/?LinkId=29349. I can make this error go away by changing the application pool to run in 32 bit mode by changing the "Enable 32-Bit Applications" setting to true. However I would prefer not to have to do that to resolve the issue. My questions are: Why is the Microsoft Request Routing feature trying to load a 32 bit version, isn't there a 64 bit version for it? How do I resolve this issue without having to change my application pool to a 32 bit mode?

  Read the article

• Slow Routing Over LAN (Wired)

  - by reverendj1

  I'm having issues with my router acting very slow (Adtran Netvanta 3458). We have two networks, let's call them A and B. When I run netperf from two servers on network A (no routing) I get speeds along the lines of 900 Mbps. Which makes sense, since we have all 1Gbps switches. When testing A to B (or vice-versa) I get speeds along the lines of 22Mbps. I have also tested connecting my laptop to the switchports on the router, and testing two servers on network A (no routing) and got speeds around 90 Mbps. Which makes sense since the switchports on the router are 100Mbps. Does anyone have any idea why routing would be so slow? We bought the router over a year ago, and we think it has been doing this since then, but we never actually tested it before. (network B isn't really used much, so we didn't notice much) We were implementing a site-to-site VPN and noticed it was ridiculously slow, so we started testing basic routing performance. I have ruled out cabling and router CPU/memory utilization. Adtran looked at my config, but didn't see anything wrong with it.

  Read the article

• Finding new IP in a file

  - by Gary

  Hello. I have a file of IP addresses called "IPs". When I parse a new IP from my logs, I'd like to see if the new IP is already in file IPs, before I add it. I know how to add the new IP to the file, but I'm having trouble seeing if the new IP is already in the file. !/usr/bin/python from IPy import IP IP = IP('192.168.1.2') f=open(IP('IPs', 'r')) #This line doesn't work f=open('IPs', 'r') # this one doesn't work for line in f: if IP == line: print "Found " +IP +" before" f.close() In the file "IPs", each IP address is on it's own line. As such: 222.111.222.111 222.111.222.112 Also tried to put the file IPs in to an array, but not having good luck with that either. Any ideas? Thank you, Gary

  Read the article

• comparing actual IP with partial IP in PHP

  - by aslum

  Using PHP I'd like to compare an actual ip address to part of one, and see if it matches. For example I want to see if the address matches 12.34.. <?php $rem_address = getenv('REMOTE_ADDR'); $temp = substr ($rem_address,0,6) if ($temp == "12.34.") echo "It's a match"; ?> Is there an easier/better way to do this?

  Read the article

• How to block IP address or IP classes in ASP.NET

  - by FinalDestiny

  I need to block one IP address or class in asp.net Can anyone help me with the code? And how to implement? Thanks

  Read the article

• Windows XP/7: custom routing for VPN connection

  - by Peter Becker

  We are dealing with a badly configured VPN connection from a vendor, which set up the default gateway but doesn't route traffic anywhere beyond their VPN zone. I managed to do some ad-hoc routing to configure a computer in a way that it can reach the vendor's VPN, our local network as well as the internet. I then tried to turn this into a script, but that failed since the interface number of the VPN changes on every connection. Is there a way in Windows XP and/or Windows 7 to configure custom routing on the client side of a VPN connection? What I would like to do is to have a script running just after the connection comes up that changes the routing table (similar to an ifup script on UNIX).

  Read the article

• Is Internet routing (BGP) fully automated?

  - by Adal

  If all the routing tables on the Internet would be erased simultaneously, will the routers be able to rediscover them automatically? I'm having an argument with a colleague who says that the RIPE routing tables are essential, but I remember reading that if the tables disappeared, the BGP protocol will allow routers to rediscover working routes between nodes by querying their neighbors which in turn will query their neighbors until a working route will be detected. Then that route will be used to repopulate the routing tables. After a while, all the routes will be restored (not necessarily the optimal routes). Is that correct?

  Read the article

• How to find the static ip address of my router?

  - by OSX NINJA

  I bricked my Linksys WRT54GS router when trying to change the firmware on it from dd-wrt to open-wrt. In order to unbrick it, I need to be able to do an ftp transfer to it. The problem is that it isn't using DHCP addressing and I can't just use the default ip address of 192.168.1.1. I have to use the ip address it was set at before it got bricked. The problem is I forgot what that number was. Is there some program or script that can find it out?

  Read the article

• Change the default route without affecting existing TCP connections

  - by Patrick Horn

  Let's say I have two public network addresses on my server: one NAT through an ISP (192.168.99.0/24), and a VPN through a different ISP (192.168.1.0/24), already configured with a per-host route to the VPN server through my ISP. Here is my initial routing table. I am currently routing through my ISP on subnet 192.168.99.0/24. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.99.1 0.0.0.0 UG 0 0 0 eth1 55.66.77.88 192.168.99.1 255.255.255.255 UGH 0 0 0 eth1 192.168.99.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Now, I want new TCP connections to switch to my 192.168.1.0/24 so I type the following: $ route add -net 0.0.0.0 gw 192.168.1.1 dev tap0 When I do this, it causes some long-standing TCP connections to hang. Is there a way to I safely change the default interface for new connections, while allowing existing TCP connections to use the old route (i.e. do I need enable some sort of stateful routing table)? I am okay with a solution that only works with established TCP connections, and I don't care how hacky it is. For example, if there is a way to add temporary iptables rules for existing connections to force them over the old route. But there has to be some way to do this. EDIT: Just a note about a simple "route add -host ... " for existing connections: this solution would work if I am fine with leaving a subset of IPs on the old interface. However, in my application, this actually doesn't solve my problem because I want to allow new connections to come on the new interface even if they have the same source IP. I'm now looking at using the "ip route" command to set source-based routing rules.

  Read the article

• How to find the static ip address of my router? [migrated]

  - by Wintermute

  I bricked my Linksys WRT54GS router when trying to change the firmware on it from dd-wrt to open-wrt. In order to unbrick it, I need to be able to do an ftp transfer to it. The problem is that it isn't using DHCP addressing and I can't just use the default ip address of 192.168.1.1. I have to use the ip address it was set at before it got bricked. The problem is I forgot what that number was. Is there some program or script that can find it out?

  Read the article

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• why do Vagrant docs suggest using public IP address 33.33.33.10 for local VMs?

  - by Gert

  I'm following a tutorial to set up vagrant (a tool to build and configure portable virtual machine images), and it seems that vagrant documentation suggests using IPv4 address 33.33.33.10 to configure a new box. That is a publicly routed IP adress, so I'm a bit confused why using this address is suggested. Since I don't own this network, I should not use an address from the 33.33.33.10/8 range. Am I correct in thinking that I should only use either a public address from a network I own, or an address from one of the private ranges as defined in RFC 1918? If so, why does Vagrant documentation suggest otherwise?

  Read the article

• What's required to enable communication between two IP ranges located behind one switch?

  - by Eric3

  Within our co-located networking closet, we have control over two ranges of 254 addresses, e.g. 64.123.45.0/24 and 65.234.56.0/24. The problem is, if a host has only one IP address, or a block of addresses in only one range, it can't contact any of the addresses in the other subnet. All of our hosts use our hosting provider's respective gateway, e.g. 64.123.45.1 or 65.234.56.1 A host on the 64.123.45.0/24 range can contact the 65.234.56.1 gateway and vice-versa Everything in our closet is connected to an HP ProCurve 2810 (a Layer 2-only switch), which connects through a Juniper NetScreen-25 firewall to the outside world What can I do to enable communication between the two ranges? Is there some settings I can change, or do I need better networking equipment?

  Read the article

• Routing Essentials

  - by zharvey

  I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

  Read the article

• Routing public IPs (each a /32) through a VPN to another server

  - by Lee S

  Hopefully the title makes sense; I have a server currently in a colo facility, with many IP addresses routed to it. They are individual IPs and not in a contiguous block. Due to vastly improved connectivity (fibre) at home I am slowly bringing my infrastructure in-house for managability and eventually, cost savings. What I would like to do though is use the IP addresses allocated to my existing server, at home. I have an IP block allocated to me on my new ISP connection, but for a couple of reasons I'd like to make use of the colo ones for now: Ease of transition - lots of domains, dns, hard-coded IPs in programs, etc. Connectivity fallback. If my primary line goes down and switches to fallback 1 (dsl) or fallback 2 (4G), I lose access to the ISP-allocated IP block of IPs that are only presented on the primary WAN interface. What I'd like to achieve is my home virtualisation server (Proxmox/Debian-based) "dials in" to the colo server in the colo facility (also Proxmox/Debian) via VPN or similar, and gets to make use of the IP addresses that currently terminate on the colo box. If the primary connection to my ISP goes down and one of the fallback routes kicks in, the VPN tunnel will just time out and then be re-established on the backup connection instead. I'm sure this is doable, but I have no idea how. I'm not afraid to get my hands dirty, I just don't really know where to start?

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing.

  Read the article

• Set up two IP addresses with one gateway?

  - by Ahmed

  I would like to ask if it is possible to set up two static IPs from same subnet through one gateway? and How if it is? What I am interested in is described here Routing for multiple uplinks/providers, but in my case I have two IP addresses from one provider, both are on same subnet and off course I have internet access on both. I have two NICs, but I don't mind to go with one if that makes it possible. Any thought is appreciated!

  Read the article

• Gateway IP for eth0 and gateway IP for pptp vpn are same

  - by user286630

  My problem is.. 1) I'm using laptop at school. 2) In school, the default gateway for ethernet is 192.168.1.1. 3) I want to connect to a pptp vpn server. The gateway over the vpn connection is also 192.68.1.1. (The VPN server assigns 192.168.100.1 to my laptop and I confirmed that it is not used in school.) In this situation, there is no problem in Windows 7. I think it is enough smart to distinguish two different gateways with the same IP. All connection requests may be forwarded to the vpn gateway. But, in Ubuntu, I cannot access a file server in the remote site. I guess every connection request is forwarded to the ethernet gateway. How can I send all connection requests to the vpn gateway whose IP is same as the ethernet gateway?

  Read the article

• In Ruby on Rails Routing I Would Like to Use Dash `-` Instead of Underscore `_`

  - by pablitostar

  I would like all the URLs for my web applications to use dash - instead of underscore _ for word separators. I'm surprised about a couple of things really: Google et al. continue to distinguish them. That RoR doesn't have a simple global configuration parameter to map - to _ in the routing. Or does it? I found a few questions here and elsewhere, but the best solution I've seen is to use :as or a named route. That's quite annoying. So I'm thinking of modifying the Rails routing to check for that global config and change - to _ before dispatching to a controller action. But before I do that, I'm hoping someone can save me the trouble! Thanks in advance for any help, or even confirmation that my approach makes sense. I'd submit it back. BTW, I'm currently on 2.3.8, but hope to migrate to 3 soon.

  Read the article

• How to set up IP forwarding on Nexenta (Solaris)?

  - by Gleb

  I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

  Read the article

• Question about network topology and routing performance

  - by algorithms

  Hello I am currently working on a uni project about routing protocols and network performance, one of the criteria i was going to test under was to see what effect lan topology has, ie workstations arranged in mesh, star, ring etc, but i am having doubts as to whether that would have any affect on the routing performance thus would be useless to do, rather i'm thinking it would be better to test under the topology of the routers themselves, ie routers arranged in either star, mesh ring etc. I would appreciate some feedback on this as I am rather confused. Thank You

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >