Search Results

Search found 285 results on 12 pages for 'modprobe'.

Page 7/12 | < Previous Page | 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Installing Microsoft VX1000 webcam

  - by KRistian

  I found a tutorial with people saying it works; here are the instructions I followed. I opened a shell as root on my system and launched the following: wget http://linuxtv.org/hg/v4l-dvb/archive/tip.tar.gz tar zxvf tip.tar.gz cd v4l... (whatever the newly created directory name is) make all sudo make install Then I edited /etc/modprobe.d/blacklist-custom and added blacklist sn9c102. After reboot, I launched sudo gstreamer-properties. However when I type tar zxvf tip.tar.gz it displays: tar: You may not specify more than one `-Acdtrux' or `--test-label' option Try `tar --help' or `tar --usage' for more information. Why? How can I do this? Thanks in advance.

  Read the article

• Atheros Wireless card shows up as two different models?

  - by geermc4

  Hi I've been fighting these wireless drivers for a few days and just recently i noticed that the model the Wireless controller appears in lspci is different sometimes. This is the data i have after installing Ubuntu Server 64 bit ~# lspci -k .... 04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1d89 Kernel driver in use: ath9k Kernel modules: ath9k ran some updates, restarted, all was good, all though it did say that linux-headers-server linux-image-server linux-server where beeing kept back. After that i installed ubuntu-desktop (aptitude install ubuntu-desktop --without-recommends) restarted and not only is the wireless not working anymore, but the hardware is listed as a different card ~# lspci -k .... 04:00.0 Ethernet controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) has no available drivers for it, still i tried to modprobe ath9k, they show up in lsmod as loaded, but still iw list shows nothing. this is what it looked like before the ubuntu-desktop instalation Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (14.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning) * 2472 MHz [13] (14.0 dBm) (passive scanning) * 2484 MHz [14] (17.0 dBm) (passive scanning) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS. What's with the hardware change? If it has 2, how can i make the AR9285 always load and disable AR5008, or, is it the same and it's just showing it different? :| Oh and I've tried this on Ubuntu 10.04 server, xubuntu 12.04, ubuntu 12.04 desktop and server. Thanks in advanced. -- Here's some more info, i have it setup in 2 hard drives, 1 works and the other one i'm using to figure it out The one that works... # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.147 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 74:2f:68:4a:26:73 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-18-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:fea00000-fea0ffff Here's where it doesn't # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.160 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network UNCLAIMED description: Ethernet controller product: AR5008 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fea00000-fea0ffff Update I've noticed that if i blacklist the ath9k and ath9k_common modules lspci gives me the AR9285, but then I need to modprobe ath9k for it to work, does this make any sense? If so, why?

  Read the article

• Can't get Broadcom 43142 drivers to work after installation on 5420 Inspiron

  - by beckett

  I'm a complete newbie to ubuntu, I've already installed and reinstalled the Broadcom driver required done a numerous amount of steps on terminal but I can't seem to get wireless working. However, my wired connection seems to work just fine. also I have tried to follow the instructions but get stuck at step number 2 when i get told "No package dpkg is available": 1) Download the file from the link 2) sudo yum install dpkg 3) mkdir BCM43142 4) dpkg-deb -x Downloads/wireless-bcm43142-dkms-6.20.55.19_amd64.deb BCM43142 5) cd BCM43142/usr/src/wireless-bcm43142-oneiric-dkms-6.20.55.19~bdcom0602.0400.1000.0400/src/wl/sys 6) sudo yum install kernel-devel kernel-headers 7) vi wl_linux.c 8) around line 43, remove the line include 9) save the file (:wq) 10) cd ../../.. 11) make Things should work, and you'll have a file called "wl.ko" in the current directory. 12) sudo yum remove broadcom-wl 13) sudo mkdir -p /lib/modules/3.5.2-3.fc17.x86_64/extra/wl 14) sudo cp wl.ko /lib/modules/3.5.2-3.fc17.x86_64/extra/wl 15) sudo depmod -a 16) sudo modprobe wl I really need help :/

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• No Wireless In Ubuntu 13.10 (maybe Need Wireless Driver) [duplicate]

  - by viktorhubinette

  This question already has an answer here: No Wireless In Ubuntu 13.10 2 answers hi after updating to ubuntu 13.10 i cant see the wireless networks on the network meny so what should i do ? tell me some commands you need to see to solve the problem. Thanks (i maybe need a wireless driver becouse i installed one when i haved 12.04 becouse i could not connect to wireless before too) i cant connect to wireless that my problem so what do i need to do to get this wireless working again? some outputs lsmod | grep rt1 nothing sudo modprobe rt18192cu FATAL: Module rt18192cu not found. iwconfig eth0 no wireless extensions. lo no wireless extensions. sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning. rfkill list all nothing

  Read the article

• Getting vga_switcheroo with ATI Mobility Radeon 5650 HD to work

  - by stevejb

  Hello! I have a new HP dv7 laptop with ATI Mobility Radeon HD 5650 graphics card, and also Intel graphics (switchable). I have done the following and want to understand what is going on with my graphics driver Resized windows 7 and did fresh install of 10.10 Booted into 10.10 and things seemed to be working okay Enabled ATI graphics, and was clearly working on the ATI rather than Intel GPU (desktop cube worked) Rebooted, got an error that modprobe could not load modules.dep, and also something about i915 symbols Rebooted into recovery mode, modified xorg.conf to remove the mention of fglrx Rebooted, and the errors show, but then x starts but clearly in intel graphics I would ideally like to be able to switch between the ATI and Intel graphics, a la vga_switcheroo. My first problem seems to be that the folder /sys/kernel/debug/vgaswitcheroo does not exist, hinting at some kind of kernel issue. What can I do to get this available? Thanks!

  Read the article

• Timeout when trying to install ubuntu 12.04

  - by Oskars

  When i click on "try ubuntu" after booting it from a USB the screen goes black and a lot of text comes out. But after a while it says "timeout: killing /blablabalba" or something like and it just keep on saying that. What have I done wrong? <.< My computer is a Acer ASPIRE M5201 if that is of any importance. Edit: I noticed now that before it says "timeout" it says something about not supporting "DNS" or "Asn" or something like that. I'm not sure if it was exactly dns and asn but do this mean that I can't run ubuntu on this computer? Edit2: The exact strings are: "[sdg] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA " "timeout: killing '/sbin/modprobe -bv pci:v00001002d00"(and more nubmers wich I didn't catch)

  Read the article

• LIRC-ZILOG on ubuntu 12.04

  - by aoman

  I followed these guides to configure a Hauppauge PVR, and after compiling the hpvr modules, I have this problem: (that also includes the zilog one) # locate zilog /lib/modules/3.2.0-29-generic/kernel/drivers/staging/media/lirc/lirc_zilog.ko /lib/modules/3.2.0-34-generic/kernel/drivers/staging/media/lirc/lirc_zilog.ko /usr/src/linux-headers-3.2.0-29-generic/include/config/lirc/zilog.h sudo modprobe lirc_zilog FATAL: Error inserting lirc_zilog (/lib/modules/3.2.0-34-generic/kernel/drivers/staging/media/lirc/lirc_zilog.ko): Invalid argument The PVR works and I can get a test video with sound. The remote does not. I want the transmitter to work so it can automatically change the channel on the cable box and find the video I wanted to record. The LIRC sources are not on Ubuntu sources and so I can only guess at what commands I might have to use. How do I resolve the error and get the remote working?

  Read the article

• Configure audio on HP ENVY 4 ultrabook

  - by phodu_insaan

  I want to configure audio for ubuntu 12.04 on my laptop. Currently the audio just does not play. If i try and plug in headphones then somewhere midway to being fully plugged in the audio plays on the headphones, I plug in further and the sound disappears. How do I get this to work? lspci | grep audio Audio device: Intel Corporation Panther Point High Definition Audio Controller My laptop is one the beats edition HP laptops, and the driver for win7 was an IDT HD audio driver. --EDIT-- The output for cat /proc/asound/card0/codec* | grep Codec is Codec: IDT 92HD91BXX Codec: Intel PantherPoint HDMI I need to get both the IDT card to work and the HDMI card to work with my TV. --EDIT-- --EDIT 2-- I have added blacklist snd-usb-audio to the end of the file /etc/modprobe.d/alsa-base.conf Now the sound plays from my laptop speakers only when I plug in a headphones/external speaker. Otherwise no sound. :( Please help getting everything working as it should. --EDIT 2-- Thanks

  Read the article

• Getting front audio jacks to work

  - by Ashfame

  I run Ubuntu 10.10 on my Intel D945. My front audio ports don't work in Ubuntu, the rear one does. I never got it working earlier when I had Ubuntu 10.04 but this time I am going to try it again. My codec is SigmaTel STAC9227 My ALSA information is here. Handy details: !!ALSA Version !!------------ Driver version: 1.0.23 Library version: 1.0.23 Utilities version: 1.0.23 !!Loaded ALSA modules !!------------------- snd_hda_intel snd_hda_intel I know something that I will have to change the model of my module to make the front audio jack works but I couldn't find a model related line in my ALSA configuration file - /etc/modprobe.d/alsa-base.conf (I was able to get to that point in Ubuntu 10.04, may be something has changed). How can I proceed from here?

  Read the article

• HP mini 5102 Ethernet does not work after suspend on Lubuntu 12.10

  - by Marcin

  Ethernet works fine after system is rebooted The onboard card is seen in 'lspci' as: 43:00.0 Ethernet controller: Marvell Technology Group Ltd. Yukon Optima 88E8059 [PCIe Gigabit Ethernet Controller with AVB] (rev 11) After system being suspended the sky2 driver loads but does not enable the NIC. I have noticed that it happens when PC is left suspended for longer period of time (few houres) Trying to reproduce it I have tried to load the sky2 driver with 'modprobe sky2'. Unfortunately typing 'ifconfig -a' for the onboard ethernet adapter does not list the driver once the sky2 driver is loaded. I have searched internet and I found some information about a bug in kernel. Hovewer it was reported in 2010 so I hope it has been fixed. Here it is http://lists.opensuse.org/opensuse-bugs/2010-02/msg01473.html

  Read the article

• Why has wireless disappeared after my 12.10 upgrade?

  - by Shay Guy

  I just upgraded to 12.10 on my Lenovo B570 laptop. NetworkManager isn't displaying a submenu for wireless connections at all, even though I downloaded the update through the wireless connection. This displeases me. Stuff I've tried includes: $ sudo modprobe wl FATAL: Module wl not found. $ sudo lspci -nn | grep "BCM" 02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) $ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no ETA: linux-headers-generic is already the newest version, and what I get when reinstalling bcmwl-kernel-source includes the following, near the end. DKMS: install completed. ERROR: Module b43 does not exist in /proc/modules ERROR: Module b43legacy does not exist in /proc/modules ERROR: Module ssb does not exist in /proc/modules ERROR: Module bcm43xx does not exist in /proc/modules ERROR: Module brcm80211 does not exist in /proc/modules ERROR: Module brcmfmac does not exist in /proc/modules ERROR: Module brcmsmac does not exist in /proc/modules ERROR: Module bcma does not exist in /proc/modules FATAL: Module wl not found.

  Read the article

• ipv6 just wont go away 12.10 server

  - by VladoPortos

  After very long time using Ubuntu old LTS version I have re-installed to new LTS 12.10, but I can't get rid of ipv6 ! I have did: in /etc/modprobe.d/blacklist.conf: blacklist ipv6 blacklist ip6table_filter blacklist ip6_tables in /etc/sysctl.conf net.ipv6.conf.all.disable_ipv6 = 1 net.ipv6.conf.default.disable_ipv6 = 1 net.ipv6.conf.lo.disable_ipv6 = 1 But ufw happily use v6 protocol, and in dmesg: ip6_tables: (C) 2000-2006 Netfilter Core Team . . IPv6: ADDRCONF(NETDEV_CHANGE): em1: link becomes ready What is going to take to get rid of IPv6 ? I swear Terminator didn't put so much fight.

  Read the article

• Installing linux on OCZ RevoDrive3 x2

  - by user2101712

  First of all, here is the configuration of my computer: Motherboard: Asus H87Plus RAM: Corsair Vengeance 32GB Processor: Intel i7 4770 Drive: OCZ RevoDrive 3 x2 (240 GB) (OCZ Revodrive3 is a PCIe module) I am trying to install the latest version of Ubuntu Desktop (13.10). The problem is that in the UEFI (bios) the drive shows up as a 240 GB drive, but in the Ubuntu installer it shows up as two 120 GB drives. If I install Ubuntu in any of these two drives, it never boots. The screen flickers a few times and comes back to the UEFI menu. I have tried reading up and have come across information that the drive has a "fakeraid", and the solution is to use dmraid. However, when I give the following commands in the terminal (from live CD): # modprobe dm_mod # dmraid -ay it says: no raid disks. And the following command: # ls -la /dev/mapper/ just shows /dev/mapper/control How can I install Ubuntu on my computer? what is the correct method?

  Read the article

• Installing Realtek rtl-8192ce on Ubuntu 9.4

  - by dutchman79

  I followed the below steps to install my rtl8192ce drivers on my Ubuntu 9.4 system. But I still got errors and nothing installed and I can't connect to the modem to get onto the Internet. Can someone please help me? Move the file you downloaded to your home directory using your file manager or terminal mv [destination of downloaded file] /home/[username] Now we move to our home directory and Unzip the file using the following command or right click and select Extract here: cd /home/user tar xvjf rtl_92ce_92se_92de_8723ae_88ee_linux_mac80211_0012.0207.2013(1).tar.bz2 Now access the Directory which we extracted cd rtl_92ce_92se_92de_8723ae_88ee_linux_mac80211_0012.0207.2013(1) Next we install the necessary dependencies to compile the driver sudo apt-get install gcc build-essential linux-headers-generic linux-headers-$(uname -r) Now we start the compilation make and then sudo make install Execute modprobe rtl8192ce Now If all went right your system should be running the wireless driver."

  Read the article

• How can I remove bluetooth-applet in 11.10?

  - by dunderhead

  I tried adding rfkill block bluetooth to /etc/rc.local. This did not work. I tried adding both blacklist bluetooth and blacklist btusb to etc/modprobe.d/blacklist.conf. This did not work. So I went to Synaptic to remove it altogether, but when I marked bluez for removal it said it was going to also remove gnome-shell as well! So naturally I didn't do that. (Is it sane to run a potential security problem like bluetooth by default? And why is something like that so tightly integrated into Gnome shell?) Can anyone tell me how to get rid of this annoying and unnecessary process?

  Read the article

• Still no wireless after b43 with Dell Inspiron 1525 (Ubuntu 12.04)

  - by DanielleN

  So I followed the instructions here http://ubuntuforums.org/showthread.php?t=1974006 about how to solve this issue. It worked for a bit and then stopped. After doing a modprobe I could at least see my network and click on it but it would not connect (I can always see it if I look under the listed wireless networks under VPN Connections, however). I'm thinking, from what I read at least, the issue might be that my wireless switch was on during those first steps. Do I now have to undo the b43 install and do it again? Or is there something else I could try? I just made the switch to Linux yesterday, so I am hesitant at this point to mess with anything on my own. I should note now that it was installed by someone who knows what they are doing, so we are all good on that front.

  Read the article

• Bad sound quality and headphones not working

  - by wifi

  Using Ubuntu 10.10, on a HP Pavilion t3019.es, which has a Realtek ALC880 soundcard. It has 6 rear jack outputs, plus digital audio input and output, plus 3 front jacks (mic, headphones and a blue one which i don't know what's for). The sound on my computer is very low, and when i raise the volume up to 50%, it starts sounding distorted, crackling. Also, the headphones don't work when i plug them (it just keeps on playing through the speakers). I tried to comment the "/etc/modprobe.d/alsa-base.conf" file according to the soundcard and jacks in my computer, but none of the lines added worked (naturally, didn't added them at once). I found out that adding "options snd-hda-intel model=generic" to it made the sound better, but it's not as good as in Windows yet. Any ideas? Other than setting the PCM value, didn't work for me. Thanks.

  Read the article

• Syanptics Touchpad Won't Re-enable

  - by user71607

  I disabled my Synaptics touchpad while a key on my keyboard and now I can't get it to work again. When I press that key again it says the touchpad turns back on but will not work at all. Rebooting doesn't help, and I tried installing touchpad-indicator but when I try to enable from there it says that it enables, but the icon remains like it's disabled. The odd thing is that it works on the lock screen so I know the drivers aren't messed up, it's just a setting. Also, the touchpad works on guest mode but still nothing on my account. I tried using gconf to set the touchpad_enable to true and it worked, it sure set it. Doesn't make a difference though, my touchpad is still useless. Terminal commands I've used: gconftool-2 --set --type boolean /desktop/gnome/peripherals/touchpad/touchpad_enabled true synclient Touchpadoff=0 modprobe psmouse

  Read the article

• Ubuntu 12.04 wireless (wifi) not working, can not upgrade to 12.10, touchpad gestures not working. What to do?

  - by Ritwik

  I installed ubuntu 12.04 LTS 3 days ago and since then wireless feature and touchpad gestures are not working. Tried everything on internet but still unsuccessful. I cant upgrade to ubuntu 12.10. These are the following comments I tried. Please help me. EDIT: just realized usb 3.0 is also not working. COMMAND lsb_release -r OUTPUT ----------------------------------------------------------------- Release: 12.04 ----------------------------------------------------------------- COMMAND lspci OUTPUT ------------------------------------------------------------------ 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) 00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05) 07:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev a1) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 07) 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01) 0f:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01) ------------------------------------------------------------------ COMMAND sudo apt-get install linux-backports-modules-wireless-lucid-generic OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-backports-modules-wireless-lucid-generic ------------------------------------------------------------------- COMMAND cat /etc/lsb-release; uname -a OUTPUT ------------------------------------------------------------------- DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.5 LTS" Linux ritwik-PC 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ------------------------------------------------------------------- COMMAND lspci -nnk | grep -iA2 net OUTPUT ------------------------------------------------------------------- 08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 07) Subsystem: Hewlett-Packard Company Device [103c:225d] Kernel driver in use: r8169 -- 0f:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:217f] ------------------------------------------------------------------- COMMAND lsusb OUTPUT ------------------------------------------------------------------- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 002 Device 002: ID 8087:8000 Intel Corp. ------------------------------------------------------------------- COMMAND iwconfig OUTPUT ------------------------------------------------------------------- lo no wireless extensions. eth0 no wireless extensions. ------------------------------------------------------------------- COMMAND rfkill list all OUTPUT ------------------------------------------------------------------- 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no ------------------------------------------------------------------- COMMAND lsmod OUTPUT ------------------------------------------------------------------- Module Size Used by snd_hda_codec_realtek 224215 1 bnep 18281 2 rfcomm 47604 0 bluetooth 180113 10 bnep,rfcomm parport_pc 32866 0 ppdev 17113 0 nls_iso8859_1 12713 1 nls_cp437 16991 1 vfat 17585 1 fat 61512 1 vfat snd_hda_intel 33719 3 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event nouveau 775039 0 joydev 17693 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq ttm 76949 1 nouveau uvcvideo 72627 0 snd 79041 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device videodev 98259 1 uvcvideo drm_kms_helper 46978 1 nouveau psmouse 98051 0 drm 241971 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 13423 1 nouveau soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm v4l2_compat_ioctl32 17128 1 videodev hp_wmi 18092 0 serio_raw 13211 0 sparse_keymap 13890 1 hp_wmi mxm_wmi 13021 1 nouveau video 19651 1 nouveau wmi 19256 2 hp_wmi,mxm_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62190 0 ------------------------------------------------------------------- COMMAND sudo su modprobe -v ath9k OUTPUT ------------------------------------------------------------------- insmod /lib/modules/3.2.0-67-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko insmod /lib/modules/3.2.0-67-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko ------------------------------------------------------------------- COMMAND do-release-upgrade OUTPUT ------------------------------------------------------------------- Err Upgrade tool signature 404 Not Found [IP: 91.189.88.149 80] Err Upgrade tool 404 Not Found [IP: 91.189.88.149 80] Fetched 0 B in 0s (0 B/s) WARNING:root:file 'quantal.tar.gz.gpg' missing Failed to fetch Fetching the upgrade failed. There may be a network problem. ------------------------------------------------------------------- COMMAND sudo modprobe ath9k dmesg | grep ath9k NO OUTPUT FOR THEM COMMAND dmesg | grep -e ath -e 80211 OUTPUT ------------------------------------------------------------------- [ 13.232372] type=1400 audit(1408867538.399:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=975 comm="apparmor_parser" [ 13.232615] type=1400 audit(1408867538.399:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=975 comm="apparmor_parser" [ 15.186599] ath3k: probe of 3-4:1.0 failed with error -110 [ 15.186635] usbcore: registered new interface driver ath3k [ 88.219329] cfg80211: Calling CRDA to update world regulatory domain [ 88.351665] cfg80211: World regulatory domain updated: [ 88.351667] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 88.351670] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351671] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351673] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351674] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351675] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------------------- COMMAND sudo apt-get install touchpad-indicator OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: gir1.2-gconf-2.0 python-pyudev Suggested packages: python-qt4 python-pyside.qtcore The following NEW packages will be installed: gir1.2-gconf-2.0 python-pyudev touchpad-indicator 0 upgraded, 3 newly installed, 0 to remove and 0 not upgraded. Need to get 84.1 kB of archives. After this operation, 1,136 kB of additional disk space will be used. Do you want to continue [Y/n]? Y Get:1 http://ppa.launchpad.net/atareao/atareao/ubuntu/ precise/main touchpad-indicator all 0.9.3.12-1ubuntu1 [46.5 kB] Get:2 http://archive.ubuntu.com/ubuntu/ precise/main gir1.2-gconf-2.0 amd64 3.2.5-0ubuntu2 [7,098 B] Get:3 http://archive.ubuntu.com/ubuntu/ precise/main python-pyudev all 0.13-1 [30.5 kB] Fetched 84.1 kB in 2s (31.6 kB/s) Selecting previously unselected package gir1.2-gconf-2.0. (Reading database ... 169322 files and directories currently installed.) Unpacking gir1.2-gconf-2.0 (from .../gir1.2-gconf-2.0_3.2.5-0ubuntu2_amd64.deb) ... Selecting previously unselected package python-pyudev. Unpacking python-pyudev (from .../python-pyudev_0.13-1_all.deb) ... Selecting previously unselected package touchpad-indicator. Unpacking touchpad-indicator (from .../touchpad-indicator_0.9.3.12-1ubuntu1_all.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for software-center ... INFO:softwarecenter.db.update:no translation information in database needed Setting up gir1.2-gconf-2.0 (3.2.5-0ubuntu2) ... Setting up python-pyudev (0.13-1) ... Setting up touchpad-indicator (0.9.3.12-1ubuntu1) ... ------------------------------------------------------------------- Not able to find ( drivers/net/wireless/ath/ath9k/hw.c ) or ( drivers/net/wireless/ath/ath9k/hw.h )

  Read the article

• How can I add usbip modules on Redhat 6 kernel?

  - by Gk.

  I have RHEL 6 with # uname -r 2.6.32-131.0.15.el6.x86_64 I'm trying to build usbip modules on staging driver. Everything is OK. I have all needed *.ko files. But I cannot add those modules on running kernel. # pwd /lib/modules/2.6.32-131.0.15.el6.x86_64 # ls | grep ko usbip_common_mod.ko usbip.ko vhci-hcd.ko # modprobe usbip FATAL: Error inserting usbip (/lib/modules/2.6.32-131.0.15.el6.x86_64/usbip.ko): Required key not available # insmod usbip.ko insmod: error inserting 'usbip.ko': -1 Required key not available How can I add it? Do I need to rebuild whole kernel? TIA, giobuon

  Read the article

• openvz and iptables

  - by rizen

  http://wiki.openvz.org/Setting_up_an_iptables_firewall mentions to load xt_state before starting a container in order to run iptables in containers. so I ran modprobe xt_state on the host and restarted the container and it worked great. To make this persist I added xt_state to /etc/modules. The problem is when I restart the physical node the containers iptables wont work unless I manually restart the container, at which point it'll work again. lsmod shows that xt_state is loaded. anyone know why my containers iptables won't work until I manually restart the container?

  Read the article

• Networked Parallel Port in Linux / KVM / QEMU

  - by korkman

  What I want to use is the "-parallel" tcp or udp option from KVM / QEMU, but I don't seem to find any server for this client. I don't serve a printer but a hardware dongle. I checked ser2net, which does provide "/dev/lp0" sharing, but it doesn't seem to work for KVM / QEMU. I suspect KVM / QEMU requires "/dev/parport0". I did rmmod lp, modprobe ppdev, linked ser2net to parport0, but it didn't work out. Perhaps ser2net is not suited for this. I tried socat as well, and I tried netcat. No success. Does anyone know any KVM / QEMU compatible parallel port server? Or did any of netcat, socat or ser2net work for you?

  Read the article

• How to use qcow2 disk image in Linux?

  - by sauparna

  I have a large qcow2 formatted disk image, which I use as storage. Often I need to move data to and from this disk image. I mount the disk using the qemu-nbd tool as follows: modprobe nbd max_part=63 qemu-nbd -c /dev/nbd0 /host/disk100G.img mount /dev/nbd0p1 /home/rup/disk But disk access fails every now and then in the midst of some I/O operation with an "Input/output error". At that point I have to manually unmount the disk and re-mount it so that I can run the program again: qemu-nbd -d /dev/nbd0 umount joborkhaki/ What could be the reason for this? Is there a better tool that I can use to maintain a qcow2 disk image?

  Read the article

• Why is this LTO4 Tape-drive not working

  - by Tim Haegele

  # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12  | Next Page >