Search Results

Search found 285 results on 12 pages for 'modprobe'.

Page 8/12 | < Previous Page | 4 5 6 7 8 9 10 11 12  | Next Page >

• How to tell X.org to reload input device module? (Working around suspend-to-ram crash on Acer laptop

  - by Vi

  When X.org boots up, Synaptics touchpad works well. But when I remove the module it falls back to /dev/input/mice and don't use normal driver even when touchpad is available again. Xorg.0.log: ... (II) XINPUT: Adding extended input device "Synaptics Touchpad" (type: TOUCHPAD) (--) Synaptics Touchpad: touchpad found # { rmmod psmouse && echo mem /sys/power/state && modprobe psmouse; } (WW) : No Device specified, looking for one... (II) : Setting Device option to "/dev/input/mice" ... How to tell X.org to try it's InputDevice again (without restarting X server)? P.S. rmmod psmouse is needed to prevent crashing of Acer Extensa 5220 when resuming from suspend-to-ram. Update: Found answer myself: Doing xinput set-int-prop "Synaptics Touchpad" "Device Enabled" 8 1 after reloading the kernel module reloads touchpad. Now suspend-to-ram works OK.

  Read the article

• How to tell X.org to reload input device module?

  - by Vi

  When X.org boots up, Synaptics touchpad works well. But when I remove the module it falls back to /dev/input/mice and don't use normal driver even when touchpad is available again. Xorg.0.log: ... (II) XINPUT: Adding extended input device "Synaptics Touchpad" (type: TOUCHPAD) (--) Synaptics Touchpad: touchpad found # { rmmod psmouse && echo mem /sys/power/state && modprobe psmouse; } (WW) : No Device specified, looking for one... (II) : Setting Device option to "/dev/input/mice" ... How to tell X.org to try it's InputDevice again (without restarting X server)? P.S. rmmod psmouse is needed to prevent crashing of Acer Extensa 5220 when resuming from suspend-to-ram. Update: Found answer myself: Doing xinput set-int-prop "Synaptics Touchpad" "Device Enabled" 8 1 after reloading the kernel module reloads touchpad. Now suspend-to-ram works OK.

  Read the article

• ifconfig return "unknown interface: no such device"

  - by xolstice

  I'm trying to install a Linux driver for my wireless network card (D-Link DWL-G510) on my Red Hat Linux 7.1 machine with a 2.4.37.9 kernel. I downloaded the serial monkey driver from the sourceforge site and was able to successfully compile the rt73 module and load it into the kernel. The problem now is that everytime I issue the command ifconfig wlan0 up it keeps returning with the following error message: wlan0: unknown interface: No such device. I'm at a loss as to what to do here. I specifed wlan0 as the alias for the rt73 module in the modules.conf and also tried to load the driver with the command modprobe rt73 ifname=wlan0 (this specifies the interface name according to the instructions packaged in the driver), but the error message still keeps coming up. Is there something else I need to do in Linux to configure the wlan0 part or is the module not recognizing the wireless network card? It would be quite strange if it is the later since all information from the Internet is indicating this is the linux driver I should be using for mentioned wireless card.

  Read the article

• How to Set Linux Bonding Interface to Gigabit

  - by Kyle Brandt

  I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

  Read the article

• Bonding: works only from one link

  - by Crazy_Bash

  I would like to install bonding with 4 links. but only one of them is active. eth4 is always active. the others simply don't work. those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1

  Read the article

• Help about NAT with virtual server

  - by Thanh Tran

  I have a dedicated server running Linux CentOS 5.3 with 2 IP addresses. I've installed a virtual machine using VMware Server. The host and the guest have a host-only network. Now I want to map the 2nd IP address to the virtual machine so that it can run as a second dedicated server for me. Here is what I do: modprobe iptable_nat echo "1" > /proc/sys/net/ipv4/ip_forward iptables -t filter -A FORWARD -s 192.168.78.128 -d 64.85.164.184 -j ACCEPT iptables -t nat -A PREROUTING -d 64.85.164.184 -i eth0 -j DNAT --to-destination 192.168.78.128 iptables -t nat -A POSTROUTING -s 192.168.78.128 -o eth0 -j SNAT --to-source 64.85.164.184</p> But it not working as intended. What is the matter?

  Read the article

• PPP connection between PalmOS and Ubuntu (over ttyUSB0?) without crashy "visor" kernel module

  - by Chris Boyle

  I have a Palm Treo 680 which I'd like to use as a media remote, using Palm MPC. Almost the exact instructions on that page used to work perfectly for establishing a PPP connection over the USB cable; I think I last tried it in Ubuntu 9.04 (Jaunty). In Karmic, I find that /dev/ttyUSB{0,1} are not present by default, and when I modprobe visor to get them, the Palm immediately crashes and reboots, as seen in Ubuntu bug 522753 (it reboots again as long as the module is still loaded and USB is still connected). The usbserial module has the same result. From reading that bug and elsewhere, it appears that the visor module is abandoned, and jpilot and friends use some other approach to talk to PalmOS over USB these days, which might not even involve a ttyUSB device. My question is, therefore: How do I create a PPP connection between PalmOS and Karmic without crashing the Palm?

  Read the article

• Gentoo baselayout-2 problem with module parameters

  - by Alakdae

  I recently switched to baselayout-2 on my Gentoo machine but I have one problem. I autoload a module bttv with paramater: card=77,77 The problem is that at boot the module is loaded without the parameter which makes the video feed useless. I cannot find the cause because the funny thing is that when I put an echo in /etc/init.d/modules to see what is passed to modprobe, this is what I got: szymanowicz ~ # /etc/init.d/modules restart * WARNING: you are stopping a boot service * Caching service dependencies ... [ ok ] * Loading module bttv ... bttv card=77,77 [ ok ] * Autoloaded 1 module(s) It indicates that everything is OK, but dmesg shows that at boot time there are no parameters. bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected] ... bttv1: using: *** UNKNOWN/GENERIC *** [card=0,autodetected] Whereas when I run it manually I get: bttv0: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option] ... bttv1: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option] Please help me because reloading the modules every time there is a reboot is very anoying (not many reboots, but I need to remember about the module)

  Read the article

• How to load tun module in linux?

  - by rabipelais

  I cannot manage to load the tun module in my archlinux box. I'm trying to connect with openvpn, but the log says nm-openvpn[6662]: Note: Cannot open TUN/TAP dev /dev/net/tun: No such device (errno=19) lsmod | grep tun returns nothing. If I run sudo modprobe tun it returns failure, but no error message, and lsmod still has no tun. The module seems to exist, as there is a tun.ko.gz in /lib/modules/....... I really dont know what else to try. Thanks in advance

  Read the article

• losetup does not decrypt device in Ubuntu 11.4 as before

  - by Kay

  I had an external volume mounted using losetup for about two years. It was created using Ubuntu 9.4 and I used the same Ubuntu installation throughout all dist upgrades. Now as I bought a new laptop I set up a fresh Ubuntu 11.4 installation on it. Problem is: losetup -e twofish /dev/loop0 /dev/sdb2 does not decrypt the volume anymore. The data in /dev/loop0 contains apparently random data. I am sure I entered the correct password. I modprobe'd cryptoloop and twofish. My question is: Has Canonical done some obscure changes to losetup like adding a salt? Does losetup depend on configuration files I did not know about? How can I decrypt the volume on my now laptop?

  Read the article

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

  - by frank

  Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

  Read the article

• Disable NSS LDAP IPv6 (AAAA) lookups

  - by pilcrow

  Question: How can I disable inet6 AAAA queries for my LDAP server during (LDAP-backed) NSS lookups on a CentOS (RHEL) 5 machine? Background: I've servers configured to consult ldap://ldap.internal for NSS passwd and group lookups. Every relevant NSS lookup, for example the getpwuid(3) implied by an ls -l which needs to translate UIDs to network user names, performs the following DNS dance before connecting to the ldap server: AAAA? ldap.internal -> (no records) AAAA? ldap.internal.internal -> NXDomain A? ldap.internal -> 192.168.3.89 I'd like to skip the first two queries completely. Configuration: [server]$ cat /etc/redhat-release CentOS release 5.4 (Final) [server]$ grep ^passwd /etc/nsswitch.conf passwd: files ldap [server]$ grep ^uri /etc/ldap.conf uri ldap://ldap.internal/ For what it's worth, IPv6 support is otherwise disabled on these systems: [server]$ grep off /etc/modprobe.conf alias ipv6 off alias net-pf-10 off [server]$ echo "$(ip a | grep -c inet6) IPv6-enabled interfaces" 0 IPv6-enabled interfaces

  Read the article

• Ubuntu PPTP VPN to Microsoft Server Command Line ONLY

  - by supreme

  I try to setup a VPN Connection from a Ubuntu 12.04 LTS to Microsoft VPN Server (Ubuntu is the Client in this Case), but I only get this error message: .. connection failed! Check the log messages below for information why. Couldn't open the /dev/ppp device: Operation not permitted FATAL: Module ppp_generic not found./usr/sbin/pppd: Sorry - this system lacks PPP kernel support Details you may need: modprobe -v ppp > FATAL: Module ppp not found. uname -r -> 2.6.32-042stab076.8

  Read the article

• Automatically detecting temperature sensors on startup (Ubuntu 10.10)

  - by dpitch40

  I am very close to achieving my goal of setting up a CPU temperature graph that is displayed in the top panel of my desktop. I have the applet and have gotten it to graph temperatures, which appear to be being sensed correctly. However, my machine doesn't find its temperature sensors by default; I have to run sudo modprobe coretemp for the sensors command to work, then log off and back in before the graph applet starts displaying my temperatures. I am wondering if I can somehow tell the kernel to load the coretemp module on startup so I don't have to keep doing these extra steps. I have tried putting this command in my startup applications, but I think its need for root permission is keeping this from working. Is there a way to set up startup applications with root permission, or some other way to ensure that this module is loaded at startup? If anyone is curious, I'm running 64-bit Ubuntu 10.10 on a Lenovo G770 laptop with a Core i5 processor and the 2.6.35 kernel.

  Read the article

• How to fix “Module ndiswrapper not found"

  - by jason328

  I have Ubuntu 12.10 and whenever I run sudo modprobe ndiswrapper, I get the following error. FATAL: Module ndiswrapper not found. The command dkms status returns with... ndiswrapper, 1.57, 3.2.0-32-generic, i686: installed The make.log in ndiswrapper returns with... DKMS make.log for ndiswrapper-1.57 for kernel 3.5.0-18-generic (i686) Wed Nov 7 22:16:12 EST 2012 make -C /usr/src/linux-headers-3.5.0-18-generic M=/var/lib/dkms/ndiswrapper /1.57/build make[1]: Entering directory `/usr/src/linux-headers-3.5.0-18-generic' LD /var/lib/dkms/ndiswrapper/1.57/build/built-in.o MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/crt_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/hal_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/ndis_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/ntoskernel_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/ntoskernel_io_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/rtl_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/usb_exports.h CC [M] /var/lib/dkms/ndiswrapper/1.57/build/crt.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/hal.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/iw_ndis.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/loader.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/ndis.o /var/lib/dkms/ndiswrapper/1.57/build/ndis.c: In function ‘NdisGetCurrentProcessorCounts’: /var/lib/dkms/ndiswrapper/1.57/build/ndis.c:2657:24: error: ‘struct kernel_stat’ has no member named ‘cpustat’ /var/lib/dkms/ndiswrapper/1.57/build/ndis.c:2658:31: error: ‘struct kernel_stat’ has no member named ‘cpustat’ /var/lib/dkms/ndiswrapper/1.57/build/ndis.c:2659:17: error: ‘struct kernel_stat’ has no member named ‘cpustat’ make[2]: *** [/var/lib/dkms/ndiswrapper/1.57/build/ndis.o] Error 1 make[1]: *** [_module_/var/lib/dkms/ndiswrapper/1.57/build] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-18-generic' make: *** [modules] Error 2 I have installed commons, utils-1.9, dkms, source but it's still returning this error. How do I fix this?

  Read the article

• Mouse pointer strange problem...

  - by Paska

  Hi all, i have last ubuntu installed (10.10), but from an year and thousand updates, video drivers updates, an hundreds of tricks, the mouse pointer is showed like an UGLY square... These are the screenshots: First Second I have no idea what to do to solve this problem. Anyone of you have an idea to solve it? Edit: this problem was encountered from 8.10+! Edit 2, Video card specifications: paska@ubuntu:~$ hwinfo --gfxcard 35: PCI 100.0: 0300 VGA compatible controller (VGA) [Created at pci.318] UDI: /org/freedesktop/Hal/devices/pci_1106_3230 Unique ID: VCu0.QX54AGQKWeE Parent ID: vSkL.CP+qXDDqow8 SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:00.0 SysFS BusID: 0000:01:00.0 Hardware Class: graphics card Model: "VIA K8M890CE/K8N890CE [Chrome 9]" Vendor: pci 0x1106 "VIA Technologies, Inc." Device: pci 0x3230 "K8M890CE/K8N890CE [Chrome 9]" SubVendor: pci 0x1043 "ASUSTeK Computer Inc." SubDevice: pci 0x81b5 Revision: 0x11 Memory Range: 0xd0000000-0xdfffffff (rw,prefetchable) Memory Range: 0xfa000000-0xfaffffff (rw,non-prefetchable) Memory Range: 0xfbcf0000-0xfbcfffff (ro,prefetchable,disabled) IRQ: 16 (10026 events) I/O Ports: 0x3c0-0x3df (rw) Module Alias: "pci:v00001106d00003230sv00001043sd000081B5bc03sc00i00" Driver Info #0: Driver Status: viafb is not active Driver Activation Cmd: "modprobe viafb" Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #17 (PCI bridge) Primary display adapter: #35 paska@ubuntu:~$ thanks, A

  Read the article

• Connecting to MSP430 via /dev/ttyACM0

  - by speciousfool

  I'd like some suggestions about how to fix garbled serial output from a device connected on /dev/ttyACM0. Lately I've been working on a development project making use of TI's MSP430 microcontroller (specifically the eZ430-RF2560). Over on this thread you can see we've been testing some code and have found that the output of the microcontroller over serial is garbled. The btstack provides simple counter test program. When we run the program and look at the serial port output using PuTTY on Windows 7 we see: rfcomm_send_internal cid 117 doesn't exist! BTstack counter 26230 rfcomm_send_internal cid 117 doesn't exist! BTstack counter 26231 However if we connect from various Ubuntu clients we get something like: Stt.R. BTacn 0 BTacn 002BTacn 0 BTcct 04BTtacoe 5BTacun My current belief is that this is because the device is being detected by cdc_acm as a generic USB ACM device. Another thread about a similar microcontroller suggests that the device should use a specific usb serial driver. We've verified that the module is compiled on our system and did a "modprobe ti_usb_3410_5052" but this had no effect on cdc_acm. Here is the relevant section of the kernel's debug log: [ 2735.092987] usb 2-1.2: new full speed USB device number 5 using ehci_hcd [ 2735.213655] cdc_acm 2-1.2:1.0: This device cannot do calls on its own. It is not a modem. [ 2735.213669] cdc_acm 2-1.2:1.0: No union descriptor, testing for castrated device [ 2735.213720] cdc_acm 2-1.2:1.0: ttyACM0: USB ACM device [ 2745.241996] generic-usb 0003:0451:F432.0003: usb_submit_urb(ctrl) failed [ 2745.242023] generic-usb 0003:0451:F432.0003: timeout initializing reports [ 2745.242401] generic-usb 0003:0451:F432.0003: hiddev0,hidraw0: USB HID v1.01 Device [Texas Instruments Texas Instruments MSP-FET430UIF] on usb-0000:00:1d.0-1.2/input1 So, in summary, we'd like to figure out how to properly connect to this device. Also of use may be the appropriate place to file a bug report.

  Read the article

• xvidcap: Error accessing sound input from /dev/dsp

  - by stivlo

  I'm running Ubuntu 11.10 and I'm trying xvidcap to record a screencast with audio from the microphone, however it can't record any sound: $ xvidcap --file appo.avi --cap_geometry 700x500-0+0 Error accessing sound input from /dev/dsp Sound disabled! Sure enough /dev/dsp doesn't even exist: $ sudo ls -lh /dev/dsp ls: cannot access /dev/dsp: No such file or directory I found a blog post about fixing xvidcap sound input, however if I try the suggestion I get: $ sudo modprobe snd-pcm-oss FATAL: Module snd_pcm_oss not found. So the question is, how can I create /dev/dsp? The problem behind the problem is: how can I record sound from the microphone with xvidcap? So workarounds are welcome too. UPDATE: I've followed the suggestion of James, and something has improved. The error accessing /dev/dsp is gone, however now I get: [oss @ 0x8e0c120] Estimating duration from bitrate, this may be inaccurate xtoffmpeg.c add_audio_stream(): Can't initialize fifo for audio recording Now when I record xvidcap appears in the recording tab of pavucontrol and I can choose Audio stream from Internal Audio Analog Stereo or Monitor of Internal Audio Analog Stereo, I tried both just in case, but the video is still mute. UPDATE 2: I found that "Monitor of" is the one to record application sounds, while for microphone, I should choose "Internal Audio Analog Stereo". To rule out other problems, such as with the microphone, I tried with gnome-sound-recorder and it works. Actually I jumped on my chair, since the volume was too high! :-)

  Read the article

• Davicom Semiconductor, Inc. 21x4x DEC-Tulip not detected by Wireshark but IP operational

  - by deepsix86

  Recently flipped to Ubuntu 11.10 on a Dell 4300 (Intel). Getting IP address and no issues (ping/surf) but Wireshark unable to detect eth0 interface. I see references in forums to blacklist tulip but looks like I am running dmfe. Not sure if the blacklist is required and where to go from here. Maybe Driver update? Got a little lost looking in that area. Some h/w details below (IP/MAC/HOSTNAME removed) Linux xxxxxx 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 17:34:21 UTC 2012 i686 i686 i386 GNU/Linux network-admin (HOSTS TAB) does not list eth0, only loopback and bunch of IPv6 interfaces ifconfig eth0 Link encap:Ethernet HWaddr xxxxxxxx inet addr:192.168.x.xx Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: xxxxxxxxxxx 64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36662 errors:0 dropped:1 overruns:0 frame:0 TX packets:24975 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42115779 (42.1 MB) TX bytes:3056435 (3.0 MB) Interrupt:18 Base address:0xe800 lspci 02:09.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) Subsystem: Device 4554:434e Flags: bus master, medium devsel, latency 64, IRQ 18 I/O ports at e800 [size=256] Memory at fe1ffc00 (32-bit, non-prefetchable) [size=256] Expansion ROM at fe200000 [disabled] [size=256K] Capabilities: [50] Power Management version 2 Kernel driver in use: dmfe Kernel modules: dmfe hwinfo --netcard 20: PCI 209.0: 0200 Ethernet controller [Created at pci.318] Unique ID: rBUF.0NgK5ZS9c0D Parent ID: 6NW+.siohrLUzzI4 SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:09.0 SysFS BusID: 0000:02:09.0 Hardware Class: network Model: "Davicom 21x4x DEC-Tulip compatible 10/100 Ethernet" Vendor: pci 0x1282 "Davicom Semiconductor, Inc." Device: pci 0x9102 "21x4x DEC-Tulip compatible 10/100 Ethernet" SubVendor: pci 0x4554 SubDevice: pci 0x434e Revision: 0x31 Driver: "dmfe" Driver Modules: "dmfe" Device File: eth0 I/O Ports: 0xe800-0xe8ff (rw) Memory Range: 0xfe1ffc00-0xfe1ffcff (rw,non-prefetchable) Memory Range: 0xfe200000-0xfe23ffff (ro,non-prefetchable,disabled) IRQ: 18 (61379 events) HW Address: 00:08:a1:01:35:70 Link detected: yes Module Alias: "pci:v00001282d00009102sv00004554sd0000434Ebc02sc00i00" Driver Info #0: Driver Status: dmfe is active Driver Activation Cmd: "modprobe dmfe" Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #11 (PCI bridge)

  Read the article

• Asus Sonic Master on Asus N53SV

  - by David Winchester

  I have read that there's a problem to get the subwoofer working in these laptops. I tried this solution No sound from external subwoofer but I don't how to prove that the subwoofer is properly functioning. I use Pulseaudio equalizer and the bass sound seems to work fine, but when I go to the Sound Settings, I can't move the bar where it says 'Subwoofer' in my sound card option, so I don't know if everything is alright. If someone has a solution I would like to know, because there isn't much information regarding this. By the way, I'm using Ubuntu 12.04 64 bits. Thanks beforehand, Dave EDIT ----------- Possible Solution Well, I will post a solution that worked for me and I think it will help a lot of users. I finally got the subwoofer working. Besides adding in /etc/modprobe.d/alsa-base.conf the line options snd-hda-intel model=asus-mode4 I deleted the lines with load-module module-combine and module-combine-sink in /etc/pulse/default.pa (in the home folder there's also a ~/.pulse/default.pa file, I don't know if it has the lines too) To assure all the channels are working, I think this command tells me that speaker-test -c6 -l1 -twav I use pulseaudio-equalizer and the bass sounds very well when properly adjusted. Also, all the channels seems to work fine and the sound is even better than in Windows (where I don't have an equalizer). I pointed out before a module-combine and module-combine-sink problem, because one day I turned on my laptop and pulseaudio didn't work. So I deleted the lines with that names (don't know if they came by default, maybe I added them sometime when I was trying to fix my speakers). After all this, I can now move the Subwoofer bar in the Sound configuration. Anyways, the Equalizer does a great job and it improves the sound a lot.

  Read the article

• unable to load nvidia(bumblebee) in ubuntu 14.04 (only nouveau loads)

  - by Ubuntuser

  Bumblebee stopped working on my system after upgrading to stable version of Ubuntu 14.04. DUring installation I get this error rmmod: ERROR: Module nouveau is in use Setting up bumblebee (3.2.1-90~trustyppa1) ... Selecting 01:00:0 as discrete nvidia card. If this is incorrect, edit the BusID line in /etc/bumblebee/xorg.conf.nouveau . bumblebeed start/running, process 11133 Processing triggers for initramfs-tools (0.103ubuntu4.1) ... update-initramfs: Generating /boot/initrd.img-3.14.1-031401-generic Setting up bumblebee-nvidia (3.2.1-90~trustyppa1) ... Selecting 01:00:0 as discrete nvidia card. If this is incorrect, edit the BusID line in /etc/bumblebee/xorg.conf.nvidia rmmod: ERROR: Module nouveau is in use bumblebeed start/running, process 18284 It says nouveau is in use. I checked the loaded modules lsmod | grep nouveau nouveau 1097199 1 mxm_wmi 13021 1 nouveau ttm 85115 1 nouveau i2c_algo_bit 13413 2 i915,nouveau drm_kms_helper 52758 2 i915,nouveau drm 302817 7 ttm,i915,drm_kms_helper,nouveau wmi 19177 3 dell_wmi,mxm_wmi,nouveau video 19476 2 i915,nouveau However, I have nouveau in my blacklist cat /etc/modprobe.d/blacklist.conf | grep nouveau blacklist nouveau blacklist lbm-nouveau alias nouveau off alias lbm-nouveau off My grub is also set to nomodeset cat /etc/default/grub | grep nomodeset GRUB_CMDLINE_LINUX_DEFAULT="nomodeset quiet splash" My graphics card is nvidia optimus lspci | grep -i vga 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 01:00.0 VGA compatible controller: NVIDIA Corporation GT218M [GeForce 310M] (rev ff) I've raised a bug in launchpad: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1327598 Note: Nvidia-prime is working for me (partially). Frequent mouse locks. Interestingly, bumblebee works perfectly fine on my fedora 20 partition on this same laptop.

  Read the article

• Trying to use HUAWEI E173 on Ubuntu 12.04

  - by Scott Warren

  I have a HUAWEI E173 usb stick to access the internet. It works normally on windows but I need to use it on my Ubuntu system. I plug it in, and after 25-20 seconds the status light turns green and blinks twice every 3 seconds. I see no changes in my system whatsoever, nothing gets installed, I don't get prompted for my PIN. I tried to create a connection using edit connections. I entered the following parameters: Turkey, Turkcell, My Plan is not listed, Internet. Nothing happens. I tried the lsusb command and got the following: tosh2000@tosh:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 058f:a001 Alcor Micro Corp. Bus 001 Device 004: ID 12d1:14ba Huawei Technologies Co., Ltd. I tried the usb-devices command and can see the device: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=14ba Rev=00.00 S: Manufacturer=HUAWEI Technology S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Based on other advice I found, I tried the following command: sudo modprobe usbserial vendor=0x12d1 product=0x14ba Again, nothing happened. My question is why does the "enable mobile broadband" not populate automatically in the dropdown networking menu and how can I can I start using the device? Thank you.

  Read the article

• Help find correct alsa model for onboard sound (alc887?) that will work with jack and have correct mixer setup

  - by Jazz

  I have a Gigabyte GA-MA74GMT-S2 motherboard. I am using Jack for sound - connected to ALSA. I am running Ubuntu 12.04. aplay -l reports card 0: SB [HDA ATI SB], device 0: ALC887 Analog [ALC887 Analog] The problem is that the default setup, that alsa decides to use, causes stuttering and xruns no matter how generous I set the frames/period or periods/buffer etc. Also, Jack works fine if I plug in an external USB sound system and use that. My processor is an AMD phenom x4 945, and I have 8GB ram, and Video card is Geforce GTX550 Ti, all of which should be quite capable enough. I also tried Pulseaudio and that works fine, but I need to use Jack At first I thought it might be an interrupt conflict, but I have found that adding "options snd-hda-intel model=generic" to /etc/modprobe.d/alsa-base.conf causes it to play correctly, but the limited mixer setup lacks controls I need - so this setup isn't good enough. Still, it seems to prove it isn't a hardware conflict. I have tried many other models, such as 3stack, 6stack, auto and even basic, and they all suffer from the stuttering. I eventually found "options snd-hda-intel model=3stack-6ch-intel" works without stuttering, and mixer is much closer to what it needs to be. Can anyone help on how to get a correct and accurate model for ALSA to use? More info on the hardware that might help... *-multimedia description: Audio device product: SBx00 Azalia (Intel HDA) vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 14.2 bus info: pci@0000:00:14.2 version: 00 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=snd_hda_intel latency=32 resources: irq:16 memory:fe024000-fe027fff

  Read the article

• Failed to get i915 symbols, graphics turbo disabled

  - by Optimus Prime

  I'm getting "Failed to get i915 symbols, graphics turbo disabled" error message after installing following softwares and few updates from Ubuntu. Django, Mysql server 5.5 Mysql benchmark And i have installed few updates for ubuntu. It was showing as Security Updates for Ubuntu. After installing Updates the update manager showed that i should restart the system. On restart i got following error message. " failed to get i915 symbols, graphics turbo disabled". So i tried the work around mentioned here (using the Live CD) ie add intel_ips to the blacklist echo "blacklist intel_ips" /etc/modprobe.d/blacklist.conf add i915 and intel_ips to /etc/modules echo -e "i915/nintel_ips" /etc/modules Now when start the system it freezes at Ubuntu splash screen. I'm using Ubuntu 12.04 LTS, on Dell inspiron N1040. I need to boot the system as i have spend lot of days configuring. Python and Django. Please help EDIT : OK when i restarted the system yesterday it magically turned on. Now i can view my desktop. But one problem, i can't mount any of the drives. It says failed to mount Drive. I'm also frequently getting "Ubuntu System Failure" Error Message.

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12  | Next Page >