Search Results

Search found 3413 results on 137 pages for 'addresses'.

Page 70/137 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

• Configure Windows Routes for VPN

  - by Florin Sabau

  I have a Virtual PC/VMWare machine that runs Windows Server 2003. This virtual machine uses an IPSec VPN client program to connect to a remote network. I configured the virtual machine to have 2 NICs: NAT - to be used by the VPN Client to access the remote network Host only - to be able to access the virtual machine from the host The reason I have this setup is because I want to be able to access some remote network from the host machine. I could've installed the VPN client on the host machine, but the host runs Windows 7 and the client doesn't support it. The problem: although the virtual machine is normally reachable (ping + http access), as soon as the VPN client is started, neither of the NIC addresses are reachable anymore. I'm wondering if it is a routing problem that needs to be addressed? How do routing/VPN client connection affect the ability of the server to respond to client requests from the host?

  Read the article

• Public folder emails not being delivered

  - by Rob

  Hello, We have just introduced an Exchange 2010 installation into our existing Exchange 2003 (all standard) environment. We make a lot of use of our Public Folders in 2003, so I am wanting to make a small PF tree in the 2010 system to test some applications against. I have created a few public folders in the 2010 public folder management tool, and mail enabled them, gotten email addresses, etc. However, mail will not be delivered, it queues on my existing 2003 Exchange server's 'Local Delivery' queue, and eventually times out and bounces. I guess the Exchange 'system' including the new 2010 server thinks that all public folder email must need to be delivered to the old 2003 server. Is it possible for me to have two public folder databases that each receive mail? If so, is there something I am missing to enable this? Thanks -R

  Read the article

• Hosted Exchange 2010 Send As

  - by Ravi

  I have a hosted exchange 2010 and I am trying to setup the Send-As permission. I am following http://technet.microsoft.com/en-us/library/bb676368.aspx which basically describes the commands for achieving this. I have user account aaa and bbb [PS] C:\Windows\system32get-mailbox -organization myorg -identity "aaa" Name Alias ServerName ProhibitSendQuota ---- ----- ---------- ----------------- aaa aaa mx1 4.95 GB (5,315,022,848 bytes) [PS] C:\Windows\system32get-mailbox -organization myorg-identity "bbb" Name Alias ServerName ProhibitSendQuota ---- ----- ---------- ----------------- bbb bbb mx1 4.95 GB (5,315,022,848 bytes) Now, when I use the command below to give bbb permission to send-as aaa, I get the following error: [PS] C:\Windows\system32get-mailbox -organization myorg -identity "aaa" | Add-ADPermission -Extended Rights "Send As" -user "bbb" mx1/Microsoft Exchange Hosted Organizations/myorg/aaa wasn't found. Please make sure you've typed it correctly. + CategoryInfo : InvalidArgument: (:) [Add-ADPermission], ManagementObjectNotFoundException + FullyQualifiedErrorId : D2FD338,Microsoft.Exchange.Management.RecipientTasks.AddADPermission The error message that 'aaa' was not found does not make sense because i just retrieved the mailbox in the previous commands. I have tried using email addresses instead of alias but it does not work.

  Read the article

• What is a good custom MAC address? [closed]

  - by rausch

  My new notebook has been dropping the WiFi connection infrequently. The reason was, that my PS3 had the same MAC address. I changed the MAC address of my notebook and the WiFi is now stable. At first I just reduced the address' last block by 1, which happened to be the MAC address of another device. I reduced it again and for now it's fine. In order to avoid conflicts in the future, is there an address range that is safe to use for custom/non-vendor MAC addresses?

  Read the article

• XenServer VM's lose network settings

  - by Ash

  We deploy virtual machines using Citrix XenServer 6.0 for our clients. Two seperate clients experience the same issue: when a Server 2008 virtual machine is restarted, the static IP addresses (network address, subnet, gateway, primary DNS) don't appear to apply correctly as the IP's cannot be pinged, network services cannot be accessed etc. The issue is resolved by manually switching the network adapters to DHCP, then re-setting them to the original static IP's. While not a major issue, it's a pain when restarting servers due to Windows Updates, plus iSCSI drives need to be manually connected to Windows again via iSCSI Initiator. We have tried removed the network adapters from the virtual machine under XenCentre but without luck. Anyone experienced similar issues?

  Read the article

• Email solution for new domain [on hold]

  - by user196286

  I registered my domain at NameCheap, and have it hosted now at AWS Route 53. However, I'm at a loss for how now to set up sending transactional email. I hear Amazon SES is a good solution, but that requires me to verify my e-mail. I don't have email set up (no e-mail addresses at my domain nor a email client to receive the email verification). As an added wrinkle, I have my sitename.com bucket redirecting to www.sitename.com, and I'm hosting my site on Route 53 using www.sitename.com. However, does this screw things up if I need to switch my MX records since perhaps the 'www' throws things off (would it point to mail.www.sitename.com)?

  Read the article

• Setting up routing for MS DirectAccess to a VMWare EsXi Host

  - by Paul D'Ambra

  I'm trying to set up DirectAccess on a virtual machine so I can demonstrate it's value and then if need be add a physical machine to host it. I'm hitting a problem because the Direct Access machine (DA01) needs to have 2 public addresses actually configured on the external adapter but there is a Zyxel Zywall USG300 between the VMware ESXi host and the outside world. I've summarised my setup in this diagram If I ping from the LAN to 212.x.y.89 I get a response but if I ping from the VM I get destination host unreachable. I used "route add 212.x.y.89 192.c.d.1" and get request timed out. At that point I see outbound traffic allowed on the Zyxel firewall but nothing coming back. I'm past my understanding of routing and VMWare so am not sure how to tie down where my problem lies (or even if this setup is possible). So any help massively appreciated. Paul

  Read the article

• Vlookup to retrieve an ID from table using text match

  - by Federico Giust

  I've got an excel spreadsheet where I would normally use a VLOOKUP. In this case I need to find the ID of the record when comparing email addresses, so the email address is the unique id here. For example on sheet 1 A B C D Person Id | Family Name | First Name | Email #N/A | Doe | John | [email protected] On Sheet 2 A B C D Person Id | Family Name | First Name | Email 12345 | Doe | John | [email protected] Basically on sheet 1 I've got 800 records, on sheet 2 450. I know the 450 are in Sheet 1, so I need to find the ids of those, and put them on sheet 1 where I've got lots more data for each person. What I've tried so far is a VLOOKUP, but I keep getting an error. I'd like to do it with some sort of formula and not using any copy paste and remove duplicates. Any ideas?

  Read the article

• Routing to a Terminal Services Cluster

  - by Dave

  I am trying to connect to a Load Balanced Windows 2008 R2 cluster using Remote Desktop Services. I have no trouble connecting to the the Servers' IP addresses (.253.16 and .253.17) or the Cluster address (.253.20) from inside the subnet (.253). The trouble is when I try to connect from the other subnet(.251). I can remote to the other non-clustered servers (.253.12 and .253.15) inside the .253 subnet from the .251 without an issue. I receive a ping reply from the cluster and other servers when I am on the .251 subnet. But when I try to connect via remote desktop it times out but only to any of the IPs on the cluster (.20,.17,.16). My ASA 5510 handling the routing reports message in the log: Deny TCP (no connection) from 192.168.251.2/4283 to 192.168.253.16/3389 flag FIN PSH ACK Here is a picture if it helps http://dl.dropbox.com/u/4217864/terminal%20server.jpg Thanks for any help

  Read the article

• Debian 6 Internet connection sharing aka IP masquerade not working

  - by Rautamiekka

  The problem: the computers [Xbox 360 and a Kubuntu 12.04.1 laptop] can't access Internet through a recently-installed desktopless Debian 6 laptop (which is wirelessly connected to a WLAN station) but addresses are successfully given by dnsmasq. The attempts: 1.1) /etc/dnsmaq.conf conffed according to http://wiki.debian.org/HowTo/dnsmasq: add lines interface=eth0 dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h 1.2) Follow http://www.cyberciti.biz/faq/rhel-fedora-linux-internet-connection-sharing-howto/ and use their script to setup iptables. 2) Follow the Ubuntu Internet Gateway Method (iptables) at https://help.ubuntu.com/community/Internet/ConnectionSharing recommended and which worked at Share internet in Linux. The Debian laptop was rebooted many times and between each attempt, with and without the script auto-executing via /etc/rc.local. While adding the iptables-restore command to that file I disabled the script.

  Read the article

• Send all traffic over VPN connection not working Windows VPN host

  - by Adam Schiavone

  I am trying to get a mac (10.8) to connect to thru vpn to a server running Windows Server 2008 R2 pass all requests from the mac to the server. The VPN is setup and I can connect and access the server thru a web browser, but for all other sites, the DNS lookup fails. I have tried adding a DNS server to the VPN Host. ex. Lets say the the VPN server also hosts a website example.com. I connect to the VPN with my mac and point a browser to example.com and everything works fine. but when I point the browser to google.com it just sits there and will eventually come back with a DNS lookup failed message. HOWEVER: I tried running the command dig @myServersIpHere www.google.com. on the mac and it comes back with correct IP addresses. I really dont know what to do from here. How can I route all requests from my mac, thru my windows server via VPN?

  Read the article

• Access Bind9 DNS in Virtualbox on Host

  - by Philipp Melab

  I've set up a Ubuntu 10.04 Virtual Box with a Bind9 DNS server. The Box has a NAT Network connection for internet access and a host-only adapter for static ip connections from the host (OSX Lion). Thats the only way i managed to get internet and static ip inside the box, guess there is a better one ... The DNS works fine from inside the virtualbox, but not from the host. The http and ftp on the guest system is accessible via both addresses, so connection between host and guest are fine i guess. I tried to add both IP's as name servers. I'm completely new to Bind9 and DNS configuration. Anybody has a hint for me whats wrong? Or how i have to configure the DNS server?

  Read the article

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• Updating Cisco VPN config to add vpnc support

  - by Igor Kuzmitshov

  I have a Cisco 1841 configured for VPN connections of two types: Peer-to-peer for partners' routers (IPsec) — using different crypto isakmp key and crypto map with set peer, set transform-set, match address for every peer (same map name, different priorities). That crypto map name is added to the WAN interface. Client access (PPTP) — using vpdn-group with accept-dialin protocol pptp. Now, a new partner wants to connect using vpnc client. The latter needs IPSec ID (group name) and IPSec secret in addition to username and password. I guess that IPSec secret is pre-shared key that can be specified in crypto isakmp key on Cisco. But I could not find any VPN tutorials involving groups. Hence, my questions: How to add IPSec ID (group name) and IPSec secret on Cisco router for vpnc connections? Should I add a new crypto map matching all addresses as well? Is it possible to add this configuration without breaking the existing setup? Thank you.

  Read the article

• How do I configure tinydns (with fefe's IPv6 patch) to listen on IPv6 address?

  - by Christian Hudon

  I'm setting up my network to support IPv6. I have static IPv6 addresses assigned to each interface of my router, and radvd advertising different prefixes on each interface. The next step would be to get my dnscache (from djbdns) working on IPv6. Said dnscache has fefe's IPv6 patch applied, so I assume it should work with IPv6. However, I can't find any documentation online on how to make the patched dnscache listen on IPv6. How do I configure tinydns and dnscache to listen on IPv6 too?

  Read the article

• DNS record question

  - by Just plain me

  So I have two Windows domains/seperate forests. One forest consist of what is left of the bought-out company's domain. They have 5 servers that still have important data and need to be worked with on a daily basis by a large group of employees. We have a forest level trust setup to ease file access. We manually create DNS A records for the 5 servers so their short names would resolve to the IP addresses. I need the FQDN to resolve though. Should I create CName records to achieve this? I hope this question makes sense, I am learning DNS on the fly... :)

  Read the article

• Multicasting and multicast address

  - by Zia ur Rahman

  I have confusion about the multicast addresses, I have read an example which is given by. Suppose two applications have been built to send audio over a network. One application accepts and digitizes an audio input stream, and then sends the resulting frame across the network to other application. The second application receives the digitized audio from the network, converts it back to the audio signal and plays the result over a speaker. Unless the two applications use broadcast to send frames, no other computers on the network will receive a copy of the frame. Multicasting provides an excellent solution to the problems of allowing some computers to participate in audio transmission. To use multicasting , a multicast address must be chosen for the audio application. And the receiving application passes the multicast address to the network interface. The interface begins to accept the packets sent to that address. Question: how this multicast address is chosen, how the receiving application knows that the sender using this specific destination address for the audio frames.

  Read the article

• Why use FQDN as DNS-server option in DHCP?

  - by Filip Haglund

  I've seen multiple default configurations of DHCP-servers with a FQDN set as the DNS-server option. Doesn't this imply a catch-22, or the need for that DNS-server to be in the hosts file of every single client? example from dhcp3-server in debian 6: option domain-name-servers ns1.internal.example.org; I can see how using a dns name is convenient because it's only an A-record to change, and they can be load balanced if wanted, but I don't see how the client is going to resolve the name. Why are people using FQDN's as DNS-server addresses in DHCP?

  Read the article

• Postfix Inbound/Outbound Gateway for Google Apps

  - by geofflee

  I currently have a Postfix/Dovecot setup, but our server is hitting capacity, so we decided to switch to Google Apps. However, we have certain web applications that need to send and receive e-mail directly (for example, e-mail being redirected to a script). What I want to do is host certain e-mail accounts with Google Apps, while my current server continues to manage other e-mail accounts. I assume this means that I would use my current server as an Inbound/Outbound Gateway, so my questions are: 1) How do I setup Postfix as an Outbound Gateway without making it an (insecure) open relay? 2) How do I setup Postfix as an Inbound Gateway so that only certain e-mail addresses are forwarded to Google Apps? Thank you!

  Read the article

• Nginx Rate Limiting by Referrer?

  - by SteveEdson

  I've successfully set up rate limiting on IP addresses like so, limit_req_zone $binary_remote_addr zone=one:10m rate=1r/s; But I was wondering if its possible to do the same on referrers? For example, if a site gets placed in an iframe on a third party site, which generates too much traffic to handle. I can't find any nginx variables for the referrer anywhere. Is this possible? Or can the solution be achieved in a different way? Thanks.

  Read the article

• IP camera's multicast/RTSP conflicting with 2.4GHz Wi-Fi?

  - by jayson

  Here at our business we have a Netgear R7000 running DD-WRT. I have been slowly adding IP cameras which I run using Blue Iris software. The last camera I bought (which is NOT a wireless camera), when I plug it into the network I start having really bad connection issues on the 2.4GHz Wi-Fi network. The 5GHz works fine, just the 2.4GHz all of the sudden has trouble connecting, as if it's conflicting. I've tried playing with the camera settings, different IP addresses, HTTP ports, etc, and discovered it to be a conflict with multicast. When multicast is checked, the Wi-Fi has issues but my video streams via Blue Iris. When unchecked, Wi-Fi works fine but the video won't stream through Blue Iris. The problem is there are no settings in the camera to change the RTSP port, which is set to 34567. Does anyone know something that could fix this issue? It all seems very strange to me but maybe someone has an idea?

  Read the article

• Network topology question

  - by Asbie

  We currently have three networks, X.X.163.1, X.X.93.1 and 192.168.1.1. Today's setup is like this: http://i.imgur.com/tkKWy.jpg We now have PPT VPN from internet to the X.X.163.1-network, but really need to access the files from the File Server through VPN. I am also aware that this setup is not optimal. So please, any advices on how to redesign our network? Rack servers are mostly web and db servers, with only public IP addresses.

  Read the article

• associate dhcp requests with subdomains in dnsmasq

  - by Dezra

  I have dnsmasq running as a dns server with a number of linux boxes using static ips that run several virtual hosts on subdomains. I currently have the following address line in my dnsmasq.conf to map the subdomain of a boxes address to the boxes static ip: address=/.devbox1.mydomain.com/192.168.1.3 address=/.devbox2.mydomain.com/192.168.1.4 e.g. site1.devbox1.mydomain.com > maps to devbox1 static ip, site1 virtual host site2.devbox1.mydomain.com > maps to devbox1 static ip, site2 virtual host site3.devbox2.mydomain.com > maps to devbox2 static ip, site3 virtual host I was wondering if I can change the machines over to DHCP addresses (instead of static) and have dnsmasq use the dhcp ip instead of the static one? Can I modify the address line to refer to the DHCP address (obviously, I cant hardcode the address)? I know I could add mac address to ip allocation, but I want to avoid this if possible.

  Read the article

• dd-wrt Bonjour/ netbios etc on two subnets

  - by user72182

  Hi I was wondering if any clever people out there could help me. I have a network setup with two different subnets 192.168.1.0 and 192.168.0.0 one router is connected to a VPN (via OpenVPN) the other is not. Both routers have static routes to each other and a device on one can communicate to another without issues when using IP addresses. My problem is I want to use services like Bonjour, Netbios and Apple Talk across the two networks, which currently does not work. A laptop connected on one subnet will not see a laptop connected on another. Is there anyway that you can connect the two networks together so these sort of local service will work??? I guess I have to forward the boardcast packets but I have no idea how to do this. Thanks for any help...

  Read the article

• Get sessions' remote IP from Teamviewer log file

  - by etuardu

  I'd like to know who has logged in to my machine and when. I have two TeamViewer log files: Connections_incoming.txt and TeamViewer7_Logfile.log. The first one is quite plain and lists, as its name says, the incoming connections to the machine, reporting the local name of the remote host, login time, logout time, and some ids. e.g.: 173274362 MYLAPTOP 20-02-2012 17:32:16 20-02-2012 17:50:42 Master RemoteControl {C5AAE483-ED0B-54B8-9235-7AE597CAD342} This is almost all what I need, but unfortunately no remote IP address is reported here, so I checked for IPs in TeamViewer7_Logfile.log but it is really messy. It indeed contains some IP addresses but I can't understand which one is bound with the items in the first log file. Is there a way to interpolate the two logs to get what I need? Should I search the second file for some particular text? What do you suggest?

  Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >