Search Results

Search found 21692 results on 868 pages for 'win key'.

Page 709/868 | < Previous Page | 705 706 707 708 709 710 711 712 713 714 715 716  | Next Page >

• Ping: sendmsg: operation not permitted error after installing iptables on Arch GNU/Linux

  - by estol

  Yesterday I got a new computer as my homeserver, a HP Proliant Microserver. Installed Arch Linux on it, with kernel version 3.2.12. After installing iptables (1.4.12.2 - the current version afaik) and changing the net.ipv4.ip_forward key to 1, and enabling forwarding in the iptables configuration file (and rebooting), the system cannot use any of its network itnerfaces. Ping fails with Ping: sendmsg: operation not permitted If I remove iptables completely, networking is okay, but I need to share the Internet connection to the local network. eth0 - wan NIC integrated on the motherboard (no idea of vendor, probably HP). eth1 - lan NIC in a pci-express slot (Intel Gigabit CT Desktop http://www.intel.com/content/www/us/en/network-adapters/gigabit-network-adapters/gigabit-ct-desktop-adapter.html) Since it works without iptables(server can access the internet, and I can login with ssh from the internal network), I assume it has something to do with iptables. I do not have much experience with iptables, so I used these as reference (separate from each other of course...): wiki.archlinux.org/index.php/Simple_stateful_firewall#Setting_up_a_NAT_gateway revsys.com/writings/quicktips/nat.html howtoforge.com/nat_iptables On my previous server, I used the revsys guide to set up nat, worked like a charm. Anyone experienced anything like this before? What am I doing wrong? Thanks, estol

  Read the article

• configuring vsftpd anonymous upload. Creates files but freezes at 0 bytes

  - by Wayne

  vsftpd on ubuntu after sudo apt-get install vsftpd Then did configuration as in the attached /etc/vsftpd.conf file. Anonymous ftp allows cd to the upload directly and allows put myfile.txt which gets created on the server but then the client hangs and never proceeds. The file on the server remains at 0 bytes. Here's the folders and permissions: root@support:/home/ftp# ls -ld . drwxr-xr-x 3 root root 4096 Jun 22 00:00 . root@support:/home/ftp# ls -ld pub drwxr-xr-x 3 root root 4096 Jun 21 23:59 pub root@support:/home/ftp# ls -ld pub/upload drwxr-xr-x 2 ftp ftp 4096 Jun 22 00:06 pub/upload root@support:/home/ftp# Here's the vsftpd.conf file: root@support:/home/ftp# grep -v '#' /etc/vsftpd.conf listen=YES anonymous_enable=YES write_enable=YES anon_upload_enable=YES dirmessage_enable=YES xferlog_enable=YES anon_root=/home/ftp/pub/ connect_from_port_20=YES chown_uploads=YES chown_username=ftp nopriv_user=ftp secure_chroot_dir=/var/run/vsftpd pam_service_name=vsftpd rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key Here's a file example that attempted to upload: root@support:/home/ftp/pub/upload# ls -l total 0 -rw------- 1 ftp nogroup 0 Jun 22 00:06 build.out This is the client attempting to upload...it is frozen at this point: $ ftp 173.203.89.78 Connected to 173.203.89.78. 220 (vsFTPd 2.0.6) User (173.203.89.78:(none)): ftp 331 Please specify the password. Password: 230 Login successful. ftp> put build.out 200 PORT command successful. Consider using PASV. 553 Could not create file. ftp> cd upload 250 Directory successfully changed. ftp> put build.out 200 PORT command successful. Consider using PASV. 150 Ok to send data.

  Read the article

• How to bypass resume from hibernate

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• run as dialog always pops up

  - by user12006

  I recently got some malware on a machine that I don't use for much (partly intentional). I've cleaned it, but now everytime I open any .exe the 'Run As' dialog pops up asking me which user I want to use to run the program. What causes this, and what's the fix for it? edit My process to remove the malware was as such: Disconnected from the network Deleted DisableTaskMgr reg key Inspected with Process Explorer and Task Manager and noticed that all applications were being run within another executable located in Documents and Settings...\Temp\Some.exe The system tray application was also in Documents and Settings...\Temp\SomeOther.exe I suspected that a service was in place as the system tray application would restart if it was killed, but couldn't find any service that I didn't recognize. Removed permissions from Some.exe and SomeOther.exe (on those files only) Restarted and deleted Some.exe and SomeOther.exe Deleted startup entries that were created Ran AVG Free and Windows Defender to remove anything else (they would be killed immediately before the two .exe's were removed) Cleaned registry via CCleaner note that system restores would finish saying something to the effect of 'couldn't restore system: there were no changes made'. I attempted to restore to a week ago, and I only got the malware yesterday.

  Read the article

• Black screen appears when booting new install of Ubuntu 11.10 on my desktop, cannot access Grub menu to fix

  - by izn

  I installed 11.10 on my desktop PC but get a black screen after the BIOS screen when I try to boot it. I was able to run 10.04.04 on my hard drive before installing 11.10 and I am also able to use 11.10 on my usb pendrive and CD ROM. I've tried unplugging all USB devices before booting and also upgrading from 11.10 to 11.10. Holding the shift key from the BIOS screen doesn't allow me to access the GRUB menu to try: Highlight the first entry, press “e” to edit it. Navigate to words “quiet splash”, delete them and type “nomodeset” in their place (without quotes). Press Ctrl + X to continue boot. Once on the desktop, go to System Administration Additional Drivers and activate the recommended drivers. So running 11.10 on my pendrive, I tried editing /etc/default/grub, commenting out the GRUB_HIDDEN_TIMEOUT setting by putting a '#' in front of it to display the grub menu and setting GRUB_TIMEOUT setting to a value greater than or equal to 1 e.g. GRUB_TIMEOUT=10. However, when I run sudo update-grub, I get: /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?) I get the same error with update-grub after: sudo mount /dev/sda1 /mnt and after: sudo grub-install --root-directory=/mnt /dev/sda reboot sudo update-grub Other suggestions to fix the update-grub problem: Open synaptic, then purge all the related grub installed packages and reinstall grub-pc then and finally: sudo update-grub Or use Grub Customizer http://ubuntuforums.org/showthread.php?t=1195275 What would be the best way to approach this? I'm concerned about purging "all the related grub installed packages" but if it's true some files are corrupted this would seem necessary. Also, was I executing the correct commands i.e. with mount and grub-install, before running grub-update?

  Read the article

• Trouble with local id / remote id configuration of VPN

  - by Lynn Owens

  I have a NetGear UTM firewall and a Windows machine running NetGear's VPN client. The Windows machine I can put on the UTM network and take off of it. When I am cabled into the local (internal) the following configuration works: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: User FQDN: utm_remote1.com Client: Local Id: DNS: utm_remote1.com Remote Id: (The UTM's WAN IP address) Gateway authentication: preshared key Policy remote endpoint: FQDN: utm_remote1.com But when I'm off the UTM's internal local network and simply coming in from the internet, this does not work. It simply repeats SEND phase 1 before giving up. Since I know that the UTM WAN IP is accessible from both inside and outside the network, I figured the problem was with the Client local id. So, I tried the following: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: (A DN of a self-signed certificate I created for the client and uploaded into the UTM certificates) Client: Local Id: (The DN of the aforementioned self signed cert) Remote Id: (The UTM's WAN IP address) Gateway authentication: (the aforementioned self signed cert) Policy remote end point: ... er, ... my choices are IP and FQDN.... Not sure what to put here No matter what I've tried, it just keeps repeating the SEND phase 1. Any ideas?

  Read the article

• How to create an MST for silent install using Orca?

  - by Sanarothe

  Hi. I'm trying to deploy 7zip via GPO; I assigned the original MSI, but the package installation simply doesn't take place. What I've gathered is that I need to create an MST. In the spirit of trying to learn as much as possible about it, I've opted to use Orca rather than a third-party automagic tool, but I'm at a loss as to which fields to edit. So far the only change that I've made is to give the license accepted checkbox a value of "1" instead of pointing to another key that, still, just gave it a value of "1." So, to give this some structure, How does (Or what criteria should I consider) creating a MST make the install noninteractive/silent? Do you have to manually reconfigure the MSI to simply not perform the GUI aspects? Or do I have to execute the program in silent mode after defining the variables the the installer requests? (Though, of course, it seems that would defeat the purpose of the MST) How do I determine which fields I need to edit? I've loaded the installer and it takes three inputs: License acceptance, feature set and installation location. I want all of the default values: I'm just trying to deploy it at all, not customize the installation. I BELIEVE that I should be messing with some values in the Registry table, but I really don't know. If I'm not asking the right questions, can someone point me to a THOROUGH resource or documentation for this process? I've already gone over the technet articles on basic Orca use and deployment, but I couldn't really find anything on creating MST that didn't involve a third party program in which one runs a 'dummy' installer to get the before and after snapshots. Thank you very much, Cameron UPDATE: After spending the day troubleshooting, I finally got my server to send out 7zip, but not until I had also assigned firefox. Not sure why it didn't want to send out 7zip by itself, but I also had some domain naming problems. Thanks for the input (GPResult helped enormously.)

  Read the article

• How do I renew a Web Server certificate in Windows Server 2008?

  - by Mark Seemann

  The SSL certificate for my web site just expired a few days ago, and I would like to renew it. I originally issued it two years ago using my Windows 2008 Certificate Authority, and it's worked without a hitch in all that time, so I would like to renew the certificate as simply as possible to make sure that all the applications relying on that certificate continue to work. I can open an MMC instance and add the Certificates snap-in for the Local Computer. I can find the relevant certificate under Personal, but I can't renew it. When I select Renew certificate with new key I get the following message: Web Server Status: Unavailable The permissions on the certificate template do not allow the current user to enroll for this type of certificate. You do not have permission to request this type of certificate. However, I can't understand this, as I'm logged on as a Domain Admin and I'm running the MMC instance in elevated mode. I've checked the Web Server certificate template, and Domain Admins have the Enroll permission on this template. FWIW, I also tried rebooting the server. How can I renew the certificate?

  Read the article

• SSH over HTTPS with proxytunnel and nginx

  - by Thermionix

  I'm trying to setup an ssh over https connection using nginx. I haven't found any working examples, so any help would be appreciated! ~$ cat .ssh/config Host example.net Hostname example.net ProtocolKeepAlives 30 DynamicForward 8118 ProxyCommand /usr/bin/proxytunnel -p ssh.example.net:443 -d localhost:22 -E -v -H "User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32)" ~$ ssh [email protected] Local proxy ssh.example.net resolves to 115.xxx.xxx.xxx Connected to ssh.example.net:443 (local proxy) Tunneling to localhost:22 (destination) Communication with local proxy: -> CONNECT localhost:22 HTTP/1.0 -> Proxy-Connection: Keep-Alive -> User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32) <- <html> <- <head><title>400 Bad Request</title></head> <- <body bgcolor="white"> <- <center><h1>400 Bad Request</h1></center> <- <hr><center>nginx/1.0.5</center> <- </body> <- </html> analyze_HTTP: readline failed: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host Nginx config on the server; ~$ cat /etc/nginx/sites-enabled/ssh upstream tunnel { server localhost:22; } server { listen 443; server_name ssh.example.net; location / { proxy_pass http://tunnel; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } ssl on; ssl_certificate /etc/ssl/certs/server.cer; ssl_certificate_key /etc/ssl/private/server.key; } ~$ tail /var/log/nginx/access.log 203.xxx.xxx.xxx - - [08/Feb/2012:15:17:39 +1100] "CONNECT localhost:22 HTTP/1.0" 400 173 "-" "-"

  Read the article

• Pushing updates to live server... FTP isn't cutting it... a better method?

  - by Jenkz

  I'm the lead developer in a team of 2. My partner has only just joined the project and despite using GIT for version control etc, we are still stuck in the dark ages when it comes to code deployment. Currently I make all site updates via FTP (this way I have control / responsibility over everything that goes live), using Filezilla. I've done this for years, but we now have some large PHP classes (300KB), and a lot of traffic. So in short, every time I upload a key class "general" for example, the site goes down until the file finishes uploading. This is only 5/6 seconds at a time, but this is increasingly unacceptable. I realise I can upload the file under a different name and then rename both files... but really there must be a better way? I've heard about rsyncing code across from another server, but I don't see how this prevents switching to the new file whilst uploading. We only have one server (for DB and Apache) but also use some cloud servers (for openx as an example).

  Read the article

• Why is mkfs overwriting the LUKS encryption header on LVM on RAID partitions on Ubuntu 12.04?

  - by Starchy

  I'm trying to setup a couple of LUKS-encrypted partitions to be mounted after boot-time on a new Ubuntu server which was installed with LVM on top of software RAID. After running cryptsetup luksFormat, the LUKS header is clearly visible on the volume. After running any flavor of mkfs, the header is overwritten (which does not happen on other systems that were setup without LVM), and cryptsetup will no longer recognize the device as a LUKS device. # cryptsetup -y --cipher aes-cbc-essiv:sha256 --key-size 256 luksFormat /dev/dm-1 WARNING! ======== This will overwrite data on /dev/dm-1 irrevocably. Are you sure? (Type uppercase yes): YES Enter LUKS passphrase: Verify passphrase: # hexdump -C /dev/dm-1|head -n5 00000000 4c 55 4b 53 ba be 00 01 61 65 73 00 00 00 00 00 |LUKS....aes.....| 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000020 00 00 00 00 00 00 00 00 63 62 63 2d 65 73 73 69 |........cbc-essi| 00000030 76 3a 73 68 61 32 35 36 00 00 00 00 00 00 00 00 |v:sha256........| 00000040 00 00 00 00 00 00 00 00 73 68 61 31 00 00 00 00 |........sha1....| # cryptsetup luksOpen /dev/dm-1 web2-var # mkfs.ext4 /dev/mapper/web2-var [..snip..] Creating journal (32768 blocks): done Writing superblocks and filesystem accounting information: done # hexdump -C /dev/dm-1|head -n5 # cryptsetup luksClose /dev/mapper/web2-var 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00000400 00 40 5d 00 00 88 74 01 66 a0 12 00 17 f2 6d 01 |.@]...t.f.....m.| 00000410 f5 3f 5d 00 00 00 00 00 02 00 00 00 02 00 00 00 |.?].............| 00000420 00 80 00 00 00 80 00 00 00 20 00 00 00 00 00 00 |......... ......| # cryptsetup luksOpen /dev/dm-1 web2-var Device /dev/dm-1 is not a valid LUKS device. I have also tried mkfs.ext2 with the same result. Based on setups I've done successfully on Debian and Ubuntu (but not LVM or Ubuntu 12.04), it's hard to see why this is failing.

  Read the article

• PXE boot -- kernel not found on TFTP server

  - by user70523

  I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

  Read the article

• Problem with wireless networking

  - by Rodnower

  Hello, I have atheros wifi hardware, intell chipset, gigabyte laptop and CentOS 5 installed. Now I try to use wireless network and get problems. First of all I want to say that I have 2 OS on my laptop, and when I load Windows XP I still may to access to the wireless network. First I try to get it on Linux was to make active wlan0 interface in: system - administration - network but I get: Determining IP information for wlan0... failed. Second I try also was unsuccessfully: [root 1 network-scripts]# ifup-wireless Error : unrecognised wireless request "off" This relevant output of iwconfig is: Warning: Driver for device wlan0 recommend version 21 of Wireless Extension, but has been compiled with version 20, therefore some driver features may not be available... wlan0 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 {output not in the original format} The same things are happen even if I do: modprobe wlan0 (this not get error) Important to say that modprobe not succeed to find ath_pci, tharefor I decide to download latest version of the madwifi driver from http://madwifi-project.org. I extracted this, but when I make this, this is what I get: [root 1 madwifi-0.9.4]# make /bin/sh: line 0: cd: /lib/modules/2.6.18-164.el5/build: No such file or directory Makefile.inc:66: * /lib/modules/2.6.18-164.el5/build is missing, please set KERNELPATH. Stop. I tried to set KERNELPATH, but I think that it was incorrect: [root 1 madwifi-0.9.4]# make KERNELPATH=/lib/modules/2.6.18-164.el5/kernel/ /bin/sh: cc: command not found Makefile.inc:81: * Cannot detect kernel version - please check compiler and KERNELPATH. Stop. Some one have any ideas? Thank you very much for ahead.

  Read the article

• Wireless disconnect randomly with wpa_supplicant reason=2

  - by renenglish

  I installed ubuntu-server 12.04 on my PC , and I use an usb wireless card to join the network. It works ok when I boot up my PC , but the wireless disconnects after a while. I pkill wpa_supplicant and reload the driver rtl8192cu , then it works a again. Then it disconnect again after about a random minutes. Here is the syslog: 22384 May 29 21:49:27 homecenter kernel: [ 6450.459313] wlan1: authenticated 22385 May 29 21:49:27 homecenter kernel: [ 6450.459535] wlan1: associate with f4:ec:38:45:62:74 (try 1) 22386 May 29 21:49:27 homecenter kernel: [ 6450.469080] wlan1: RX AssocResp from f4:ec:38:45:62:74 (capab=0 x431 status=0 aid=3) 22387 May 29 21:49:27 homecenter kernel: [ 6450.469085] wlan1: associated 22388 May 29 21:49:27 homecenter wpa_supplicant[2342]: Associated with f4:ec:38:45:62:74 22389 May 29 21:49:27 homecenter kernel: [ 6450.481933] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 22390 May 29 21:49:27 homecenter wpa_supplicant[2342]: WPA: Key negotiation completed with f4:ec:38:45:62:7 4 [PTK=CCMP GTK=CCMP] 22391 May 29 21:49:27 homecenter wpa_supplicant[2342]: CTRL-EVENT-CONNECTED - Connection to f4:ec:38:45:62: 74 completed (auth) [id=0 id_str=] 22392 May 29 21:49:38 homecenter kernel: [ 6461.472014] wlan1: no IPv6 routers present 22393 May 29 21:49:38 homecenter ntpdate[2263]: step time server 91.189.94.4 offset 0.012758 sec 22394 May 29 21:49:51 homecenter ntpdate[2404]: step time server 91.189.94.4 offset -0.001190 sec 22395 May 29 21:54:38 homecenter kernel: [ 6762.052030] wlan1: deauthenticated from f4:ec:38:45:62:74 (Reas on: 2) 22396 May 29 21:54:38 homecenter wpa_supplicant[2342]: CTRL-EVENT-DISCONNECTED bssid=f4:ec:38:45:62:74 reas on=2 22397 May 29 21:54:38 homecenter kernel: [ 6762.064744] cfg80211: All devices are disconnected, going to re store regulatory settings 22398 May 29 21:54:38 homecenter kernel: [ 6762.064752] cfg80211: Restoring regulatory settings 22399 May 29 21:54:38 homecenter kernel: [ 6762.064757] cfg80211: Calling CRDA to update world regulatory d omain 22400 May 29 21:54:38 homecenter kernel: [ 6762.069938] cfg80211: Ignoring regulatory request Set by core s ince the driver uses its own custom regulatory domain 22401 May 29 21:54:38 homecenter kernel: [ 6762.069943] cfg80211: World regulatory domain updated: 22402 May 29 21:54:38 homecenter kernel: [ 6762.069945] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 22403 May 29 21:54:38 homecenter kernel: [ 6762.069949] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22404 May 29 21:54:38 homecenter kernel: [ 6762.069952] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22405 May 29 21:54:38 homecenter kernel: [ 6762.069956] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22406 May 29 21:54:38 homecenter kernel: [ 6762.069959] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22407 May 29 21:54:38 homecenter kernel: [ 6762.069962] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KH z), (300 mBi, 2000 mBm)

  Read the article

• Windows 7 deployment thru WDS

  - by vn

  Hello, I am deploying new systems on my network and I built my reference computer by installing the OS the manufacturers (Dell and a custom built system from some local business) gave with all drivers, installed all the desired applications. As for the settings part, I'm doing most of it thru GPOs. I want to image my reference computer and deploy it with WDS. i found several links on how to sysprep, but they're all doing it with some differences without explaining them. My questions : How do I manage (into sysprep) the domain join/computer naming part since (from what I understand) WDS manages that? How do I know/determine what I need to setup into my sysprep.xml? Can you sysprep a first time, try and if it fails, do some modifications and try again? I am thinking of doing a basis sysprep, checking what info can be automated and correct that in the answer file. What do I miss if skipping the "audit" mode? I don't plan on re-doing the reference computer... I read that when sysprepping, it resets settings from the reference computer like the computer name, activation/key and such... what setting is sysprep resetting by default that I should be aware of? I must admit I am quite lost about Win7, sysprep, RIS, MDI toolkit, WDS.. I understand the way of doing with XP, but it changed so much with Windows 7! The links I am reading are : http://far2paranoid.wordpress.com/2007/12/05/prep-for-sysprep/ http://blog.brianleejackson.com/sysprep-a-windows-7-machine-%E2%80%93-start-to-finish-v2 http://www.ehow.com/print/how_5392616_sysprep-machine-start-finish-v2.html Thank you VERY much for any answers, they are much appreciated.

  Read the article

• I Can Edit SD Card on Windows XP but Not on Windows 7

  - by David C

  I have an 8GB SDHC card which I have used to upload pictures onto my Windows XP machine using an SD card reader ("SanDisk Ultra II"). I could also delete pictures and create folders on the card. I recently obtained a new computer that runs Windows 7 and, while I can view and upload the photos, I am unable to delete photos or create folders. When I attempt to do either of these two operations, the desired option does not appear in the menu ("Delete"/"New Folder"). Also, the shortcut keys do not work (e.g. the Delete key and Alt+F+W+F). I have attempted to change the Properties from Read-only, but am greeted with a "media is write protected". I should add that when I insert the Card Reader back into my Windows XP computer, I am granted full write permissions. Why can't I modify the SD Card from Windows 7? And, related, how can I fix this issue? Let me know if you have any additional questions. Thanks!

  Read the article

• Hyperic HQ- Monitor process statistics for 50+ processes on Linux machine

  - by Chris

  Is there an easy way to get metrics on all processes that start with the letters XYZ? I have about 80 processes that I have to monitor individually that all start with the prefix XYZ. I have created a query using the sigar shell: ps State.Name.sw=XYZ, which will give me a list of the processes that I want. What I need to do is define this list of processes through said query and collect and track statistics from the Process service: http://support.hyperic.com/display/hypcomm/Process+service What I need is 3 or 4 key statistics for each of the XYZ processes defined by my query to show up as graphs in the web front end. Note: Hyperic HQ server is installed on a windows machine and I'm monitoring a Linux box via an agent. Thanks, Chris Edit: Here is my try at a plugin that may give me what I want, but it's not being inventoried/detected by the Hyperic web UI. Simply pointing me to one of Hyperic's tutorials won't do. Thanks. <!DOCTYPE plugin [ <!ENTITY process-metrics SYSTEM "/pdk/plugins/process-metrics.xml">]> <plugin> <server name="ABCStats"> <config> <option name="process.query" description="Process Query" default="State.Name.sw=XYZ"/> </config> <metric name="Availability" alias="Availability" template="sigar:Type=ProcState,Arg=%process.query%:State" category="AVAILABILITY" indicator="true" units="percentage" collectionType="dynamic"/> &process-metrics; <plugin type="autoinventory"/> <plugin type="measurement" class="org.hyperic.hq.product.MeasurementPlugin"/> </server> </plugin>

  Read the article

• CopSSH SFTP -- limit users access to their home directory only

  - by bradvido

  Let me preface this by saying I've read and followed these instructions at the FAQ many times: http://www.itefix.no/i2/node/37 It does not do what the title claims... It allows every user access to every other user's home directory, as well as access to all subfolders below the copssh installation path. I'm only using this for SFTP access and I need my users to be sandboxed into only their home directory. If you know a fool-proof way to lock users down so they can see only their home directory and its subfolders, stop reading now and reply with the solution. The details: Here is exactly what i tried as I followed the FAQ. My copSSH installation directory is: C:\Program Files\CopSSH net localgroup sftp_users /ADD **Create a user group to hold all my SFTP users cacls c:\ /c /e /t /d sftp_users **For that group, deny access at the top level and all levels below cacls "C:\Program Files\CopSSH" /c /e /t /r sftp_users **Allow my user group access to the copSSH installation directory and its subdirectories For each sftp user, I create a new windows user account, then I: net localgroup sftp_users sftp_user_1 /add **Add my user to the group I've created Open the activate user wizard for CopSSH, choosing the user, "/bin/sftponly" and Remove copssh home directory if it exists **Remains checked Create keys for public key authentication **Remains checked Create link to user's real home directory **Remains checked This works, however, every user has access to every other user's home directory as well as the CopSSH root directory.... So I tried denying access for all users to the user home directory: cacls "C:\Program Files\CopSSH\home" /c /e /t /d sftp_users **Deny access for users to the user home directory Then I tried adding permissions on a user-by-user basis for each users home\username folder. However,these permission were not allowed by windows because of the above deny rule i created at the home directory was being inherited and over-riding my allow rule. The next step for me would be to remove the deny rule at the home directory and for each user folder, add a deny rule for every user it doesn't belong to, and add an allow rule for the one user it does belong to. However, as my user list gets long, this will become very cumbersome. Thanks for the help!

  Read the article

• OpenSSL response 404 issue on centOS 6

  - by dsp_099

  I followed this tutorial (though it's for 5.2, I figured I'd be alright). The changes I had to make that seemed to have worked: Rename ca.csr to ca.cslr (that's the one the command generated) List it in the ssl.conf as ca.cslr instead of ca.csr I have the following in the httpd.conf <VirtualHost *:80> DocumentRoot /etc/test ServerName site.com </VirtualHost> <VirtualHost *:433> SSLEngine on SSLCertificateFile /etc/pki/tls/certs/ca.crt SSLCertificateKeyFile /etc/pki/tls/private/ca.key <Directory /etc/test> AllowOverride All </Directory> DocumentRoot /etc/test ServerName cryptokings.com </VirtualHost> /test contains a folder inside of it, accessible via http://site.com/test/foo, however attempting to access it via https://site.com/test/foo results in warning that the certificate is untrusted (self-signed, no biggie) a 404 error. Chrome's complains about the certificate are the following: The identity of this website has not been verified. • Server's certificate does not match the URL. • Server's certificate is not trusted. I think those warnings are a side-effect of a self-signed certificate - or is the first one something that needs to be addressed? I seem to be able fetch the root page via https just fine though, it shows a standard CentOS setup page. (That said, I haven't added a VirtualHost entry for it so I suppose that makes sense) I think I've made a mistake somewhere during the setup as I'm not too familiar with the process. During setup, I was prompted for a type of password that would be required when apache restarts but running service httpd restart does not seem to prompt me for one. Any help would be appreciated.

  Read the article

• SQL 2000 Backup/Export Process - Can't find SQL 2000 Enterprise Manager, Can't use Mgmt Studio Expre

  - by 1nsane

  I need to make a backup of a client's SQL 2000 database, however there are a few issues preventing me from doing so using the traditional methods. I've tried using SQL Management Studio Express, but the host doesn't give sufficient privileges to create a backup and I'm getting some strange error messages. I've also tried doing the "Generate Scripts" to recreate the schema, then using the DTS Wizard to migrate the data, but the IDs set up with the identity specification property are not consistent with the live database once copied over. This results in some foreign key breakage... If I remember correctly, I was able to use Microsoft SQL 2000 Enterprise Manager to perform the task before, but I can't find this anywhere... it seems Microsoft has pulled most SQL Server 2000 stuff from their site. Does anyone know where I can find a copy of Enterprise Manager (or a trial of SQL Server 2000, which I believe comes with the component)? Or conversely, does anyone know of any other tools (preferably non-commercial) that are capable of mirroring remote SQL Server 2000 DBs? Thanks!

  Read the article

• How do I fix a corrupt calendar cache?

  - by Blacklight Shining

  I was tailing /var/log/system.log and noticed a sudden wall of text. Looking closer, I saw it was an error CalendarAgent got while trying to save something: Nov 18 11:42:45 rainbow-dash.local CalendarAgent[12321]: CoreData: error: (11) Fatal error. The database at /Users/blackl/Library/Calendars/Calendar Cache is corrupted. SQLite error code:11, 'database disk image is malformed' Nov 18 11:42:45 rainbow-dash.local CalendarAgent[12321]: Core Data: annotation: -executeRequest: encountered exception = Fatal error. The database at /Users/blackl/Library/Calendars/Calendar Cache is corrupted. SQLite error code:11, 'database disk image is malformed' with userInfo = { NSFilePath = "/Users/blackl/Library/Calendars/Calendar Cache"; NSSQLiteErrorDomain = 11; } 2 messages repeated several times Nov 18 11:42:49 rainbow-dash.local CalendarAgent[12321]: [com.apple.calendar.store.log.subscription] [WARNING: CalSubscriptionSession :: persistError :: save failed] This entire sequence is repeated many times throughout the log. file said the file in question was a SQLite 3.x database, so I did a bit of searching and came up with a way to check those. blackl% cp -i ~/Library/Calendars/Calendar\ Cache /tmp blackl% sqlite3 /tmp/Calendar\ Cache SQLite version 3.7.12 2012-04-03 19:43:07 Enter ".help" for instructions Enter SQL statements terminated with a ";" sqlite> pragma integrity_check ; *** in database main *** Main freelist: Bad ptr map entry key=863 expected=(2,0) got=(5,21) On page 21 at right child: 2nd reference to page 863 This is followed by a few dozen lines like these: rowid <number> missing from index <name> and then: wrong # of entries in index <name> I'm at a bit of a loss as to what to do now—I couldn't find anything on how to fix the errors that I found. Also, it would probably be a good idea to disable Calendar Agent so it doesn't try to use the database while it's being fixed (that's why I copied it to /tmp before running sqlite3 on it.) How do I disable CalendarAgent and fix its cache?

  Read the article

• Remote desktop solution where the desktop sharing party contacts the computer it wants to share with

  - by Kent

  I'm in a situation where I act as a sort of techinical support to my family and less techinically experienced friends. I'm looking for a remote desktop solution where it's possible to setup a "zero-install, double click an icon"-solution where the client computer contacts me so that I may interact with their desktop. The last part is important as the people in need of my help don't know how to configure their router or even the firewall software on their own computer. They are able to click an accept button when asked if a program should be able to make outgoing connections. They have many different kinds of routers, as well as software firewalls, and I rather not deal with the problem of how to connect to them using whatever as well as the actual problem they are having. It must be: Free of charge for non-commercial use. Possible to use it in a mode where the computer wanting to share its desktop should be able to make a connection to my computer. My computer has a DNS name we can use. Compatible with both Windows XP and Windows 7. Independent of a third party server or infrastructure. Explanations of the above: I don't want to spend money on it when I help them for free. If it's free as in freedom, all the better! I guess this boils down to being callable like showdesktopto.exe opscomputer.com where opscomputer.com is my computers DNS name. If that is possible then I can create a shortcut they can use to connect to me when they need help. It's nice if it's possible to specify a password or key file which I can use to authenticate myself, but it's not required. They use the OS which their machine comes installed with. That means Windows XP or 7. I want something which will work in the long run. Using a third party service which might not be available when I need it disqualified such solutions.

  Read the article

• Unable to activate Windows XP

  - by Josh Kelley

  The latest round of Patch Tuesday updates left my Windows XP computer unbootable. ("Fatal System Error: The Windows Logon Process system process terminated unexpectedly.") After much messing around with the recovery console, an XP CD's repair mode, and manually copying registry files around, I have a system that can boot again. However, I overwrote my OEM XP installation's activation information while trying to run a retail XP CD's setup, so it needs reactivation. Here's my problem: I cannot activate it at all. I log in, Windows tells me I have to activate to continue, I click Yes, and absolutely nothing happens: no windows, no response to keyboard or mouse, no response to Ctrl-Alt-Del, nothing. Safe mode works, but I can't activate in safe mode (EDIT: not even safe mode with networking). I read a trick online of pressing [Windows Key]+U to bring up the Microsoft Narrator, and that works, but clicking its Microsoft Web Site link does nothing. My last attempt to resolve this was to reinstall Windows off of the OEM CD. Now I have two parallel Windows installations, both on the same hard drive, one with all of my stuff and no way to activate it, one fully activated with no usable programs. Any ideas? Any way to activate in safe mode? Any way to copy activation information from my activated installation to my unactivated installation (since they're both on the same hard drive)?

  Read the article

• Postfix not sending email after upgrading to Ubuntu 12.04

  - by Luke

  After upgrading a server from Ubuntu 10.04 to 12.04, postfix is no longer sending email through sendgrid.com. I followed this guide about 6 months ago and everything had been working perfectly until the upgrade. Now it doesn't seem to be authenticating with sendgrid. This is the error I get in my syslog when I try to send an email. May 22 10:19:55 server postfix/smtp[3844]: 983B11C5DA: to=<to address>, relay=smtp.sendgrid.net[174.36.32.204]:587, delay=0.05, delays=0.01/0/0.04/0, dsn=5.0.0, status=bounced (host smtp.sendgrid.net[174.36.32.204] said: 550 Cannot receive from specified address <sendgrid username>: Unauthenticated senders not allowed (in reply to MAIL FROM command)) This is from postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = no config_directory = /etc/postfix header_size_limit = 4096000 inet_interfaces = loopback-only mailbox_size_limit = 0 mydestination = localhost, mylinode.members.linode.com myhostname = hostname mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relayhost = [smtp.sendgrid.net]:587 smtp_sasl_auth_enable = yes smtp_sasl_mechanism_filter = login smtp_sasl_password_maps = hash:/etc/postfix/sasl/sendgrid smtp_sasl_security_options = noanonymous smtp_tls_security_level = may smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes Any help would be greatly appreciated. I would be happy to post any other logs or other relevant information.

  Read the article

• GoDaddy SSL on Shared Hosting

  - by Jon

  So I'm very new to using SSL certificates and I have been trying to install one on a site for a client. He is using shared hosting for multiple domains through GoDaddy, and the site we're working on is not the primary domain. He purchased a UCC certificate for multiple domains and I installed it on the shared hosting account. My thought was that since the domains were under the same hosting account, then they would each be protected under the certificate. This was not the case...apparently. I checked both domains with an SSL checker and the primary domain checked out. The domain that we wanted the SSL on showed the following errors: None of the common names in the certificate match the name that was entered (www.CLIENTDOMAIN.com). You may receive an error when accessing this site in a web browser. I'm not sure how to fix this. It was just purchased yesterday, so if necessary, I guess I could un-install it or re-key it (???). Is there a way to just change the common name to www.CLIENTDOMAIN.com (the correct domain)?

  Read the article

< Previous Page | 705 706 707 708 709 710 711 712 713 714 715 716  | Next Page >