Search Results

Search found 2774 results on 111 pages for 'adapter'.

Page 71/111 | < Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >

• X-FI optical output not being recognized.

  - by Luciano

  Hello there! I have an issue and I don't know what to do! I have a SoundBlaster X-FI Xtreme Gamer, which has a spdif mini-optical output. I have it connected to a home theater, via a toslink cable and an adapter to fit in the mini plug. It used to work perfectly, but now it doesn't anymore. There is light travelling through the cable, but the HT doesn't pick up the signal. The sound card of the motherboard also has an optical output (regular, not mini) and it works ok, so the cable and the HT are fine, I think. What else should I try? Thanks, Luciano. PS: I only enabled the onboard card for testing, but usually it's disabled to avoid any kind of conflicts. PPS: I'm using Windows 7 64bit with latest drivers of everything, but like I said. It used to work.

  Read the article

• pxelinux hanging when booting client machine

  - by Blasphemophagher

  I'm kind of new to all of this, so please forgive any vagueness/misunderstandings on my part. I'm using pxelinux and VMs to create CentOS 6.0 machines that have the same install every time. I have a new VM set to boot from network, but in the process of booting up it gets stuck at "Loading 10.1.1.20:/pxelinux.0" (10.1.1.20 is the address of the server it's getting info from). pxelinux conf: http://pastebin.com/4XfZZPY1 I'm pretty sure all my config files are correct, could it be VirtualBox related? I have both the building server and the new client set to Host-only adapter and PCNET-FAST.

  Read the article

• Windows 2012 Server Hyper-V: Cannot see LAN

  - by Samuel

  I have one NIC on the machine loaded XP on the Hyper-V and had chosen the network as virtual switch. No LAN and no internet shows up on the client. Am I missing something? it used to work in 2008-R2. Details: One network card on machine (Qualcomm Atheros AR8131 PIC-E Gigabit Ethernet controller) The virtual machine hard disk is pointing to and existing XP-SP2 hard disk created using VPC 2007 The Virtual machine Network Adapter is setup as Virtual Switch to the real ethernet controller with Enable virtual LAN identification set to 2 (no other virtual machine is created in the system) After the virtual machine boots LAN shows empty in Control Panel Network Connections (this is XP client) and I also cannot access the internet. XP is showing activation prompt but as far as I know it should not disable the network! Virtual network switch is set to External

  Read the article

• Connect a 2.5" (laptop hard disk) SATA hard disk to Desktop PC

  - by Lawliet

  Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) I bought a all-in-one Modex-to-SATA power adapter and SATA cable and I still don't know what to do. I have read various forums and a lot of people are stating that it's perfectly ok, but some are scaring me that by connecting it so, it fried their hard disk. And some also mentioned cutting the yellow 12V wire if I'm planning to use Modex-to-SATA power. Thanks in advance

  Read the article

• Connect a 2.5" (laptop hard disk) SATA hard disk to Desktop PC

  - by Lawliet

  Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) I bought a all-in-one Modex-to-SATA power adapter and SATA cable and I still don't know what to do. I have read various forums and a lot of people are stating that it's perfectly ok, but some are scaring me that by connecting it so, it fried their hard disk. And some also mentioned cutting the yellow 12V wire if I'm planning to use Modex-to-SATA power. Thanks in advance

  Read the article

• magento on Zend Server (Win7) installation error

  - by czerasz

  I try to install magento for the first time. I've created the database with the name "project" in my C:\Zend\Apache2\conf\httpd.conf I added on the end: <Directory "C:\Zend\Apche2\htdocs\project"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> in my ZendServer/Server Setup/Extensions: PDO_MySQL, simplexml, mcrypt, hash, GD, DOM, iconv, curl, SOAP are on in C:\Zend\ZendServer\etc\php.ini I set: safe_mode = Off ;<-- was set to off ... memory_limit = 512M; Maximum amount of memory a script may consume (128MB) After step "Configuration" of magento installation (with Use Web Server (Apache) Rewrites enabled) I get: Internal Server Error My database is full of tables (that schould be ok) My Zend Server shows: 27-Oct 06:55 6 Severe Slow Request Execution (Absolute) http://localhost/project/index.php/install/wizard/installDb/ Critical Open 27-Oct 06:55 4 Fatal PHP Error C:\Zend\Apache2\htdocs\project\lib\Varien\Db\Adapter\Pdo\Mysql.php Critical Open 27-Oct 06:55 5 Slow Function Execution curl_exec Warning Open 27-Oct 06:55 5 Slow Request Execution (Absolute) http://localhost/project/index.php/install/wizard/configPost/ What can be wrong?

  Read the article

• OpenDNS servers initial response is very slow

  - by Ben Collins

  I've got a Time Warner cable ISP package (RoadRunner), and the modem they gave me doesn't allow me to specify which DNS servers to use; it always uses whatever the upstream dhcp server gives it. I prefer to use OpenDNS on my home network, so i've configured a couple of my PCs manually in the Windows adapter settings for IPv4 such that their IP addresses are obtained via DHCP, but the DNS server settings are fixed to the OpenDNS server IPs. Now, when I startup Windows on these PCs, it always takes 2-3 minutes to start receiving responses from the DNS servers; any request before that times out. While not debilitating, this is quite annoying. Any ideas why this might be happening?

  Read the article

• Can't get bridged networking to work between linux guest virtual machine and Mac host

  - by tgoneil

  I'm trying to establish bridged networking from linux mint vsn 12 in virtualbox to a Mac Lion host. Mac config: Network setting: en3 configured by DHCP Sharing setting: Internet Sharing selected, Share connection from en3 to computers using en3 Virtualbox Linux setting: Network setting: Bridged Adapter, Name: en3 I can ping from host (192.168.2.1) to guest (192.168.2.2) and guest to host, but I Cannot ping from the Linux guest to the outside world. Connection in host is up, because I can ping from the Mac host to the outside world. Something else that's seems weird to me, in the Mac Network setting, the IP Address generated by DHCP says 169.254.243.185. What the heck is that?? When I open a terminal up in the Mac, however, ifconfig shows its en3 inet address as 192.168.2.1.

  Read the article

• Network keeps disconnecting - Repairing solves it. Router configuration

  - by Joao Carlos

  My network connection keeps going insane, it will keep normal applications connected, like TeamViewer and MSN, but webpages will stop loading (Problem loading page). Everything looks connected and works like a charm, but webpages and new connections wont work. If I press "Repair" in the network connections to restart the adapter, it will work. This happens on WIRED and WIRELESS connections, both on Windows and on MacOSx. I have had this for years (different computers, routers, cities), but I never figured it out. I learn to live with it, but, I think theres probably a solution. What must I be doing wrong if this keeps happening? You guys have same thing?

  Read the article

• Force Steam (and other programs that do not specify proxy settings) to use a proxy

  - by joshhunt

  My school requires a proxy for all internet access. If you want to use the internet, it is impossible to not use a proxy. This makes it a problem for many programs that don't seem to let you enter proxy settings. How can I use Steam when I am behind a proxy? Is it possible to somehow enter the details into a configuration file, or force it to get the settings from Internet Explorer? If not, does software exist for creating a 'virtual' network adapter which will pass all traffic (or all protocol x traffic) through the proxy? Although I am facing this specific problem on Windows 7, solutions for all operating systems are welcome.

  Read the article

• VPN Connection causes DNS to use wrong DNS server

  - by Bryan

  I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

  Read the article

• Windows Server 2003 Standby/Sleep Results in Cold Boot when Resuming

  - by Simon Chadwick

  I'm running Windows Server 2003 sp2 on a Dell Inspiron e1705. There has never been a problem going to standby/sleep mode (by closing the laptop lid, or from the Start menu), and then resuming later. Today I did a Windows Update to install the latest patches and fixes. I don't know if there is a correlation, but now when I resume from standby/sleep mode, the machine does a cold boot. The AC adapter is connected. The battery is 2 months old, and all its LEDs light up when pressing its test button. The Power Management shows it at "99% (charging)" all the time. There is nothing suspicious in any of the event logs. Any ideas?

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Can someone recommend a Compact Flash card to be used as a boot disk/fixed disk.

  - by Hamish Downer

  I have an early Acer Aspire One netbook, and the flash drive is really slow at writing. I've taken it apart to add more RAM, but I've pretty much stopped using it. I've read about people replacing the SSD with a Compact Flash card and a CF to ZIF adapter but I've also read about some Compact Flash cards where the manufacturer has permanently disabled the boot flag to stop people doing this kind of mod. (Can't find the link any more though). (Although I have just found some info about CF cards that says "Most CompactFlash cards by default identify themselves as removable media instead of fixed disk" and that this is an issue for Windows. So my most specific question is: can someone recommend a compact flash card that does allow the boot flag to be set and to be set as Fixed Disk? Please say whether you've done it yourself, or just heard about it from someone else. Beyond that, is this generally a problem?

  Read the article

• VMWare Server 2 Install is Failing w/ Error 25032: "failed to customize windows logon process"

  - by Justin Searls

  VMWare Server 2 install question here.* Straightforward question that would probably require a VMWare expert to pull apart, given that Google has been totally worthless on this. On a patched Windows XP machine, any attempt to install VMWare Server 2.0.1 results in failure, just prior to completion (progress bar is full but I can tell network adapter stuff hasn't been fired yet and most of the services haven't been instaled). The error: Error 25032. Failed to customize Windows logon process (). Please contact your administrator. Upon dismissing the error, you're treated to: Warning 25033. Failed to remove Windows logon customization (VMGINA.DLL). Please contact your administrator. Clicking "OK" rolls back your installation. Killing the installer and hoping that it somehow leaves a working install behind was also unproductive. *I hope install troubleshooting isn't outside the purview of serverfault, I'm typically an SO user.

  Read the article

• Windows 7 USB power lose after a few seconds / minutes

  - by Stefan Dunn

  My friend's computer has a problem where the USB ports causes problems with the power of some devices connected to the computer. The USB mouse has no problems, however the Wireless Adapter looses power after around 20 seconds of use and USB Flash Drives cause the computer to either freeze, lose power (and become unresponsive) or become disconnected (still shown in Device Manager, but not in My Computer) when trying to transfer any type of file to / from the computer. I have a suspicion it's the Motherboard but could it also be a Software problem? Tried a new case, RAM, CPU and GFX Card which had no effect. The problem occurs on both the Front USB and Back (Motherboard) USB Ports. UPDATE: Tried the USB devices with an Ubuntu Live CD and they work fine, could this mean it's a problem with Windows (x64)?

  Read the article

• Oracle 11g network configuration

  - by Kylo

  I installed Oracle 11g Enterprise Edition on my Windows 7 Pro. My problem is that I cannot log into database from other host (local network). When I connect to database using Oracle SQLdeveloper everything is ok as long as I specify 'localhost' in connection configuration. However, when I change it to '192.168.0.190' which is my host IP address I get 'The Network Adapter could not establish the connection'. I get the same error when logging in from other host in local network. What is the problem?

  Read the article

• Different keyboard layouts at same time for different devices

  - by Joao Carlos

  I have a MacBook Pro running Snow Leopard, and I am using it as a portable but also desktop computer. In order to acheive this, I bought a VGA adapter and I am using it with an external mouse, keyboard, and monitor. The problem is, the external keyboard layout is different from the one on the macbook. It is set to US qwerty (its a logitech G15), and because of that, most keys behave differently than they should. Question is, how can I set up different layouts at same time for different devices? I want US for external keyboard and PT for the default one.

  Read the article

• Error installing Network driver

  - by Simon Carpentier

  I'm tring to install NetLimiter 3 (3.0.0.10, x64) on my Windows 7 x64 machine. At the driver installation step, I'm getting an error: Error 0x8004a029: Couldn't install the network component. (InstallNdisIMDriver) UPDATE 2010-09-20: I received a response to my support request: Hi Simon, It seems that problem is rather on your system than in NL3. Too many networking applications (VPN, Virtual computers) are installed on your machine and they are preventing NL3 from proper installation. In order to install NetLimiter 3, try to disable/temporarily remove these apps. Several users had the same problem and shuffling with adapter and networking software helped them. Please, let us know which action helps you (if any). Sincerely, Jan Bilek Any thoughts on this?

  Read the article

• magento on Zend Server (Win7) installation error

  - by czerasz

  I try to install magento for the first time. I've created the database with the name "project" in my C:\Zend\Apache2\conf\httpd.conf I added on the end: <Directory "C:\Zend\Apche2\htdocs\project"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> in my ZendServer/Server Setup/Extensions: PDO_MySQL, simplexml, mcrypt, hash, GD, DOM, iconv, curl, SOAP are on in C:\Zend\ZendServer\etc\php.ini I set: safe_mode = Off ;<-- was set to off ... memory_limit = 512M; Maximum amount of memory a script may consume (128MB) After step "Configuration" of magento installation (with Use Web Server (Apache) Rewrites enabled) I get: Internal Server Error My database is full of tables (that schould be ok) My Zend Server shows: 27-Oct 06:55 6 Severe Slow Request Execution (Absolute) http://localhost/project/index.php/install/wizard/installDb/ Critical Open 27-Oct 06:55 4 Fatal PHP Error C:\Zend\Apache2\htdocs\project\lib\Varien\Db\Adapter\Pdo\Mysql.php Critical Open 27-Oct 06:55 5 Slow Function Execution curl_exec Warning Open 27-Oct 06:55 5 Slow Request Execution (Absolute) http://localhost/project/index.php/install/wizard/configPost/ What can be wrong?

  Read the article

• Virtual Box ie7 won't connect to the internet

  - by j-man86

  I use IE7 & IE8 disk images from microsoft and Virtual Box to test my websites in IE. One day I stopped being able to connect to the internet with virtual box, seemingly after trying to alter proxy related settings to view Hulu.com outside of the U.S... I don't know whether it's coincidence or not. Anyway, I am using the 'PCnet-FAST III (NAT)' adapter with virtual box. Can you guys help me troubleshoot this issue? What information do you need on my current settings? Thanks so much!

  Read the article

• Compaq Presario CQ40 unexpected turn off

  - by CRoshanLG

  My Compaq Presario CQ40 (yeah, its pretty old) suddenly turns off after about 1/2 - 1 hour usage without any notice or warning. The power cable and adapter works fine (indicator bulbs show that power is given to the laptop), but it seems like machine suddenly plugged off from the power source. And when I try to switch it on, after the sudden turn off it simply won't turn on. I can only turn it on after letting it to rest for at least couple of hours! ** The battery has been dead for some time now, but it has been working fine on direct power supply until recently. Has anyone encountered this? and hopefully knows any cure?

  Read the article

• Wireless is not currently enabled

  - by ikartik90

  I have a HP Pavilion TX2000 tablet PC with me with windows 7 OS running on it. I used to access the Internet using my D-Link DIR 615 wireless adapter on the tablet and it used to work quite fine until one day, when I hibernated my Windows 7, the wireless went off and the problem seems to persist even after my hard efforts to clear it. I checked if the router works fine, and yes it did as my iPod was still catching wireless signals on the other hand, when I checked mu device manager, I realized that I now had no wireless driver. I checked on HP's website for one, but ironically even they didn't have wireless drivers meant for my tablet for Windows 7. Please help me find a solution to this problem. Further queries will be entertained as frequently as possible. Thanks.

  Read the article

• Wireless network unavailable, no networks found after Windows update

  - by jacobsee

  Old Dell Inspiron 8200 laptop with Linksys Wireless G network adapter card (WPC54G v2). Wireless connection was working fine. Then I ran a bunch of windows updates, I think the last one was the recent .NET 3.5 service pack update. Now wireless networks won't connect. Using windows to manage wireless, no networks show up. I'm typing right now on another laptop where wireless is working fine. I've restarted router & Dell laptop several times. Tried to Repair wireless connection and refresh network list. Also restarted DHCP and WZC service, all to no avail. I then uninstalled .NET 3.5 SP (don't remember number) and .NET 3.0 SP2. I don't remember all the windows updates that I just ran because I haven't used this laptop in a while so had to catch up on some updates.

  Read the article

• Diferent keyboard layouts at same time for diferent devices

  - by Joao Carlos

  Hello, I have a MacBook Pro running Snow Leopard, and I am using it was a portable but also desktop computer. In order to acheive this, i bought a VGA adapter and I am using it with an external mouse+keyboard+monitor. The problem is, the external keyboard layout is diferent from the one on the macbook. It is set to US qwerty (its a logitech G15), and because of that, most keys behave diferently from what they are supposed to. Question is, how can I set up diferent layouts at same time for diferent devices? I want US for external keyboard and PT for the default one.

  Read the article

< Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >