Search Results

Search found 2778 results on 112 pages for 'ping fm'.

Page 71/112 | < Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >

• IBM storage ds3400 Cant connect to management using fiber

  - by Eli B

  i have a problem with a DS3400 IBM storage system we bought a few years back. when i try to manage the storage using its IBM storage management i cant find it using automatic detection even though its connected directly using the fiber and i can see the Logical drives connected and working properly. when i tried to connect the two management Ethernet wires and manage the storage directly by entering the IP address manually i am able to connect however after i make several changes to the controller configuration one of the controllers stops responding and i am not able to ping it directly (since you cant make any changes without being connected to both controllers this is a problem) whats more bizarre is that when i change the IP of the controller that doesn't respond it starts working .. i have found some articles over the web explaining stuff about LUN31 being missing and causing similar problems however all my attempts to manually configure it failed . *link to an example http://www-947.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-5075711 in short im trying to get my storage to appear in the storage manager when directly connected using only the fiber cable directly attached. thanks in advance

  Read the article

• Virus blocking incoming connections ?

  - by Benoît

  Hello, on my windows 2003 server, all incoming connections are dropped. I can see them getting in using Wireshark, but even a single ping from another computer fails. All locally initiated connection work fine (i'm asking from the server). This server is the DC/DHCP/DNS/File server, so computer clients are in the dark. I've run varius antivirus and removal tools without any luck. The Windows Firewall is disabled. I'm wild-guessing at some virus/worm. How can i check why these incoming ICMP/TCP SYN/etc are dropped ? Anyone has any knowledge about such situations ? Thanks.

  Read the article

• Configure Windows Routes for VPN

  - by Florin Sabau

  I have a Virtual PC/VMWare machine that runs Windows Server 2003. This virtual machine uses an IPSec VPN client program to connect to a remote network. I configured the virtual machine to have 2 NICs: NAT - to be used by the VPN Client to access the remote network Host only - to be able to access the virtual machine from the host The reason I have this setup is because I want to be able to access some remote network from the host machine. I could've installed the VPN client on the host machine, but the host runs Windows 7 and the client doesn't support it. The problem: although the virtual machine is normally reachable (ping + http access), as soon as the VPN client is started, neither of the NIC addresses are reachable anymore. I'm wondering if it is a routing problem that needs to be addressed? How do routing/VPN client connection affect the ability of the server to respond to client requests from the host?

  Read the article

• How to statically configure DNS servers on a Cisco router when the WAN interface uses DHCP?

  - by Massimo

  I have a Cisco router (model 887VA, IOS 15.4) used to connect a LAN to the Internet via ADSL. The WAN interface uses DHCP: interface ATM0.1 point-to-point ip address dhcp I need the router to use a statically-defined DNS server for name resolution: ip name-server A.B.C.D However, the router insists on using the DNS servers supplied by the ISP via DHCP: Router#ping www.google.com Translating "www.google.com"...domain server (<ISP DNS>) [OK] Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 173.194.116.208, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/45/48 ms How can I tell the router to ignore the ISP-supplied DNS servers and only use the statically-configured one?

  Read the article

• Blocking ports on the public IP assigned to lo interface in GNU/Linux

  - by nixnotwin

  I have setup my Ubuntu server as a router and webserver by following the answer given here. My ISP facing interface eth0 has a private 172.16.x.x/30 ip and my lo interface has a public IP as mentioned in the answer to the question linked above. The setup is working well. The only snag I have experienced is that I could not find a way to block the ports exposed by the public IP on the lo interface. I tried doing iptables -A INPUT -i eth0 -j DROP, and my server lost connectivity to the public network (internet). I could not ping any public ips. What I want is a way to block ports that are exposed by the public ip on the lo interface. And also I require iptables rules that can expose ports like 80 or openvpn port to the public network.

  Read the article

• Plesk 9 VPS - Doesn't reply to NameServer requests (nslookup, etc)

  - by Ben

  Hi, I'm trying to troubleshoot a problem with a new VPS i'm setting up. The VPS is running Plesk 9 on a CentOS 5 system. Everything works fine, except it doesn't serve dns requests. If I try something like nslookup [somedomain.com] the.ser.ver.ip to test a DNS query, i get the following error ;; connection timed out; no servers could be reached I can't telnet to it on port 42 either.. I'm guessing something is blocking the requests.. firewall maybe? the plesk firewall module is installed and the nameservers entry is green. Any other way I can check what's blocking it on the server? Any help/tip greatly appreciated. Note: http works, i can telnet to the server on port 80 and i can also ping the server Thanks

  Read the article

• cant access site intermittent as i get site not available

  - by user61438

  i have a news site i check stuff for regularly.. once in a while i cant access it completely from my 5 different browsers and even from the command line, nslookup cant resolve, ping and tracert fails.. all not being able to resolve site name..the problem is specific to this.. i am told by the site support person that problem is that its cache on my machine or on ISP and I say thats not true because this site I access it 1-2-3 times a week from one browser only.. i only fire up the other ones in times of trouble..and when i have the problem even if i try on my secondary machines i still get the same problems.. when problem goes away all works well.... question is whats causing the intermittent dns/http problems... i don't believe this is something to do with my machine because probe disappears without me having done anything at all.

  Read the article

• how to connect with ssh when it's hanging

  - by Eduardo Bezerra

  I'm trying to ssh into a remote machine, but it hangs when looking for an identity file: [username@local .ssh]$ ssh -v remote uname OpenSSH_5.3p1, OpenSSL 1.0.0-fips 29 Mar 2010 debug1: Reading configuration data /home/username/.ssh/config debug1: Applying options for * debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to remote [192.168.3.36] port 22. debug1: Connection established. debug1: identity file /home/username/.ssh/identity type -1 debug1: identity file /home/username/.ssh/id_rsa type -1 debug1: identity file /home/username/.ssh/id_dsa type -1 I can ping the machine normally, and it's obviously working with the sshd service running... I just don't know how to log into it. In fact, I'd just like to reboot it. That'd be fine. Thing is: it's across the ocean (I'm in the US, and the machine is in Europe). I'd run some hundreds of java threads at the same time and apparently that was too much for the host. How can I get back in?

  Read the article

• How to share a VPN connection in a VMWare Guest VM with the Host

  - by Jonathan

  The need - This question is relevant for all of those who want to bypass their corporate's annoying VPN, and access their work/corporate network from their private computer, especially if the corporate VPN client software can't run on their private computer. Homework: this question is very similar to this one and this one, which aren't answered :( The challange - Can't run the corporate VPN client from the private computer, so converted the work laptop to a VMWare Virtual Machine. The VPN client is working fine inside the Guest VM, now we want to share it with the Host (the private computer) The specs: * The private computer (Host OS) is Mac OS X Lion 64bit * The corporate laptop (Guest VM) is WinXP 32bit, running in Bridged network mode * The VPN client on the Guest VM is is Checkpoint SecuRemote NGX R60 HFA03 * While the VPN is running in the Guest VM, the Host can still ping the Guest and vice versa

  Read the article

• Samsung i780 networking problem

  - by Infinity

  Hello guys! Maybe this is not the right place to ask this, but I give a try for it. Please don't rate it down, just ignore it if you don't like. So I have a Samsung i780 mobile phone and I would like to use the internet through my wireless router. I have connected to it. I got an IP address. My laptop is also connected to the same wireless network and I can ping the mobile phone and I get answer. When I open the internet explorer and enter an address it says that it cannot connect to the internet. I have googled very much, but can't find the problem. What do you think, what is the solution?

  Read the article

• Approach for monitoring internet backbone traffic volume

  - by Greg Harman

  I'm interested in getting a picture of relative volume across different internet backbones. In particular, I'd like to see how traffic volume over a given route differs over the course of a day or from one day to the next. InternetTrafficReport.com is the closest approximation to this that I've found online, and their approach is to test ping times to a number of key routers from several geographically-dispersed servers. This sounds like one straightforward way to measure, but I don't have several geographically-dispersed servers. Is there a different approach for sampling this type of information from a single server?

  Read the article

• Can Remote Desktop be set up to use IPv6?

  - by Garrett

  I have both a Windows 7 Ultimate and a Windows XP Professional machine set up on my home network. I would like to be able to access them from school. Port forwarding is not currently an option (long story). Is there a way to set it so that I can RDP (yes it has to be RDP not something like TeamViewer or LogMeIn) over IPv6, possibly using Teredo? I have tried but I can't seem to get it working. Also I cannot ping these machines' IPv6 addresses. How can I get this set up?

  Read the article

• Bridge and OpenVPN with shorewall

  - by Javier Martinez

  I have this scenario and everything it's working OK, but I want to configure my Shorewall and I can't do it. My interfaces are: br0 (bridge of eth0) tun0 (OpenVPN) vnet* (each one of bridged interfaces with public IP's) Public Main IP: 188.165.X.Y OpenVPN IP's: 172.28.0.x Bridge: public ip's So, I have the next configuration for shorewall: /etc/shorewall/zones #ZONE TYPE OPTIONS IN OUT # OPTIONS OPTIONS fw firewall inet ipv4 road ipv4 /etc/shorewall/interfaces #ZONE INTERFACE BROADCAST OPTIONS inet br0 detect routeback road tun+ detect routeback /etc/shorewall/policy #SOURCE DEST POLICY LOG LIMIT: CONNLIMIT: # LEVEL BURST MASK $FW all ACCEPT inet $FW DROP info road all DROP inet road DROP /etc/shorewall/tunnels #TYPE ZONE GATEWAY GATEWAY # ZONE openvpnserver:1194 inet 0.0.0.0/0 The problem is that even with shorewall running I am able to ping or connect to the virtual machines behind the bridge

  Read the article

• Juniper J4350 out of order

  - by Benjamin Baron

  I have got two (2) Juniper routers J4350 that are out of order : All the interfaces are down (leds on the interfaces don't ligthen, ping dosen't respond) No output on the console port (even when booting) I've tried to reset the router (holding the RESET CONFIG button on the front panel during 15 seconds) and nothing happened, even while booting the device I've opened the router to check the fans. I've removed some dust and nothing has changed. I wanted to precise that the leds on the front panel are all on: The POWER led is green The STATUS led is red The ALARM led is on and is orange The HA (High Availablity) is on and orange as well I have found nothing on the Internet to solve this problem... Thank you for helping me :)

  Read the article

• Unable to connect my computer from LAN (http, smb) in UBUNTU 10.04

  - by Abdul Majeed

  I installed ubuntu 10.04, Apache, PHP, mysql, smb. Everything work fine in locally in my IP. When i trying to access my computer from LAN (other computer), it shows unable to connect. when i ping my IP from remote computer, its pinging OK. I can access internet, and all other systems (http, smb). But the problem is no one can't access my computer remotely in my LAN network. My ip is 192.168.85.105 and i want access(Appaceh,SMB) from 192.168.85.10. Is there any proxy firewall settings? I had tried following commands.. sudo iptables -F or sudo iptables-restore [logout require] If it does not work then try to disable net-filter sudo ufw --disable Please give me the solution.

  Read the article

• EC2 server in VPC stops responding joining domain

  - by Geoff

  We have a EC2 Windows Server set up and running in our VPC, connected to our network via a Juniper 5GT. This is working well, with the tunnel up and stable. If I then join the server to our local domain, it appears to work - I can then log on using domain credentials, and use domain accounts when applying security to folders etc. After I log out, if I give it around an hour, the box becomes unresponsive. I can't ping it, although a tracert goes all the way barring the last hop - so the tunnel is ok. I can't RDP into it. If I reboot it, then it works for a while before doing the same thing. Un-joining it from the domain fixes the problem, and it stays up and stable. The event logs don't show anything obvious, at least to me. Any ideas?

  Read the article

• My computer is listed twice in the Network view; network shares are not accessible

  - by romkyns

  I have a couple of network shares set up on my Win7 machine. They've been in constant use, from that same machine on which they're set up. One morning they just randomly stopped working: When I went looking for what was wrong, I noticed that I also had my PC listed twice in the Network view in Explorer: "Sirius" is the name of the PC on which these screenshots were taken. I may have installed some windows updates around the time this happened. I have since tried rebooting and installing all the latest updates, to no avail. I've also removed the share in question and re-added it, making sure I give all rights to everyone. I'm an administrator on this machine, but I can't access the administrative shares (\\SIRIUS\c$) either, with the same message. I can access \\localhost\AcronisImages and \\localhost\c$, and I can ping sirius. Any ideas?

  Read the article

• Remote location looses connectivity

  - by user24559

  I have a remote location that has constant internet access using DSL. The remote location only has three Linksys cameras that use the internet access with a router. There is no computer on the network. The router is configured to use the DYN.org service to keep the IP address updated if the internet provider assigns a new ip address. The problem I am having is the router after a period of time stops responding to incoming ping requests and the cameras are shown offline. However, if I keep one of the cameras constantly streaming data then the connection to all the cameras works just fine all the time. How can I keep the router from appearing to be sleeping and not responding to incoming requests? The router is the Linksys WRT300N.

  Read the article

• Why can't I access a particular website even though the server appears to be available

  - by 50ndr33

  I can't access http://www.lynda.com/ with any of my browsers on my home network. By checking http://www.downforeveryoneorjustme.com/, I can see that the server is up and I can access it via a proxy like TOR. This screen appears immediately after I type the page in It doesn't even try to load the page, it seems. Though when I ping the server I get this: I tried to do ipconfig /flushdns. But it didn't help either. Anyone know how to fix this?

  Read the article

• Disable IPv6 on Loopback address (Localhost, Computer name, ...)

  - by Greg Bray

  We tried installing a 3rd party software product on a new Windows 2008 R2 server and found that everything works except for accessing local services through loopback addresses such as localhost or the computer name (ex: VPS-Web which resolves to localhost). We are not using IPv6 and would like to disable it until the software is compatible. I tried using these instructions for disabling IPv6 on Windows 2008 R2 but it did not disable the protocol for localhost. Pinging localhost or VPS-Web will still return ::1: instead of 127.0.0.1. I can use ping localhost -4 to get the correct address, but IPv6 takes precedent over IPv4 so the 3rd party software only gets the IPv6 address.

  Read the article

• Plesk 10 port 8443 connection timeout

  - by GriffinHeart

  I've installed plesk 10 on centOS and after installing to access the cp you need to go https::8443 I'm not being able to, and would like to find out why i can ssh to the server and i can, from the server telnet, to those ports. from another machine i can ping it but when i try to telnet or go to that address i get connection timeout, happens with port 80 and 8443 from my netstat netstat -nlp | grep 8443 tcp 0 0 :::8443 :::* LISTEN 25205/sw-cp-serverd How do i find out whats causing the problem? I also have a router but firewall is at the minimum and the server configured as DMZ, also tried to redirect 8443 to 8443 of the server.

  Read the article

• What are the things to look out for when adding other domain user to your IIS?

  - by Jack

  I have a Windows Server 2008 R2 called Jack11 that joined a domain called Watson.org. It has IIS 7 installed. From my understanding, we need to add the following into the web.config file <system.web> <identity impersonate="true" /> </system.web> Also, we need to ensure that the server Jack11 can ping to the domain Watson.org. What other setting do we need to setup in order for a user of domain Watson.org (e.g. the user Watson\User1 to access the application in the Server IIS? This is because currently, there is a problem as follows: Exception Details: System.Data.SqlClient.SqlException: Login failed for user 'WATSON\User1'. The error message was displayed when the user User1 wish to access one of the web application in server Jack11 IIS and that web application also do some retrieval of records from the database, which is installed in SQL Server 2008 Enterprise located in the same server Jack11.

  Read the article

• Unable to connect to another computer from the Task Scheduler on Windows 7

  - by Clem

  I am getting the following error when trying to connect to another computer from the Task Scheduler on Windows 7: "The remote computer was not found." The computer that I am trying to connect to is definitely on the network as I can ping it and browse its shared folders in Windows Explorer. Note that I get the same error message when trying to perform the same operation from Performance Monitor. This suggests that I need to something to enable remote connection to the Task Scheduler. I am not very experienced with Windows administration and I am not sure where to look. To give a bit more context, I want to use the Task Scheduler to automatically start Perf Mon on a few machines at my company. I'd like to setup the Task Scheduler remotely. Does anyone know what I need to do?

  Read the article

• Linksys WRT54GS V6 Router Blinking Power Light

  - by Frank

  I have a Linksys WRT54GS V6 Router in my possession got it at my local goodwill for 5$. Upon start up the Power LED starts flashing like crazy and at the same time the Ethernet ports all light up once then turn off (DMZ and WLAN never turn on). I can ping the router only by setting a static IP on my Pc. I can also successfully push a file (official Linksys OS and DD-wrt) into it via TFTP but this currently does nothing (no 192.1681.1 Access). Any ideas as to what may be wrong? I think its pretty obvious that it's bricked but.. I keep hearing a whole lot of "if it pings it's fixable" on the internet.

  Read the article

• Setting up a SQL server outside the domain

  - by user12391

  Hi, im very new to this. I've set up an account "SQLBOX" thats on the a network, but not connected to the domain. I have installed an instance of SQL Server 2008 and am trying to connect to it from another machine on the network but am getting "Cannot connect to "SQLBOX"". From the "SQLBOX" i can connect to sqlservers on the domain, but not vice-versa. Any help would be greatly appreciated. Sorry if the description isn't great. EDIT I can ping the box from a machine on the domain

  Read the article

< Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >