Search Results

Search found 2280 results on 92 pages for 'ressource pool'.

Page 71/92 | < Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• Wireless router setup for 1-1 NAT

  - by Carlos

  What I have: A linksys router WAG160N with firmware version 2 A "pool" of 5 external static IP's provided by my ISP 213.xx.xxx.n All the required configuration values for the static IPs such as (Subnet Mask, Gateway and static DNS 1, 2, 3) Current WAN Configuration: Encapsulation: RFC 2364 PPPoA Multiplexing: VC QoS type: UBR DSL modulation: MultiMode What's connected to the network: 1 x Server (That I want to make available to the outside) 5 x Desktops with static internal IP's, such as 192.168.0.xx 2 x Network printers, also with internal static IP's 2 x Laptops 1 x NAS (Network Attached Storage) also on static IP What I want to do: I would like to make the server available from outside the network, for example from your house. The problem is that Im not really sure how to do this. I have tried following the steps on the instruction manual in Linksys but they do not seem to work, once I set it up as shown bellow, I loose internet and all hell breaks loose. Going into further detail, I would prefer if the network is changed as little as possible, by this I mean that all the computers stay networked within eachother and only the server is accessible from the outside the network. What I need HELP with: I have read around that it is possible to set a 1-1 NAT (I know where it is in the menu but have no clue what it does...) so that I can NAT a single public IP directly to a single private IP (in our case the server). But please, How do I do that? Or maybe an alternative?

  Read the article

• How do I run multiple MVC apps within a subdomain on IIS7?

  - by Matthew Patrick Cashatt

  Hello and thanks for looking. Background I am currently wrapping up a development contract and the client would like for me to push a build of the application to their IIS 7-based server in which they would like to run multiple MVC apps. One of the issues I have off of the bat is that this server is already a subdomain on their larger network. So, if I enter SERVERNAME in my browser, it automatically directs to SERVERNAME.COMPANYNAME.COM. Now, this is just fine if I place my application in the default website/root. In this scenario, clicking a link that requests admin.html directs to `SERVERNAME.COMPANYNAME.COM/admin.html' as usual. BUT they want me to place the app in a subdomain on this server so that they can also run other apps on the same server. So I assume that I need MYAPP.SERVERNAME.COMPANYNAME.COM but I have no idea how to do that. Complicating matters is that my app and the future ones they wish to install are all MVC based which intercepts and re-writes URLs. I assume that this takes care of itself if I can just successfully get my app into a subdomain to begin with. What I have tried Creating a new site on the server in it's own app pool Setting the binding for that site to MYAPP.SERVERNAME.COMPANYNAME.COM Setting the binding for that site to MYAPP Setting the binding for that site to MYAPP.SERVERNAME Setting the binding for that site to MYAPP.SERVERNAME.COM Setting the binding for that site to MYAPP.COMPANYNAME.COM Nothing is working. Am I missing something simple here? Thanks, Matt

  Read the article

• Help trying to figure out why IIS7 is crashing / locking up / denying connections

  - by Pure.Krome

  Hi folks, I've got a pretty busy website that is running on a single web front end machine, on W2K8 + IIS7. Every now and then - eg. maybe monday at 3am or something, then a few days later .. some early morning time .. then nothing for 2 weeks ... etc - the website fails to respond to any client connections. ie. no one can connect to the website. I can remote desktop to the machine, etc no probs. I restart the app pool (the website is running in intergrated mode), still nothing. I try and get a crash dump of the process (it's around 600 mb maybe even more) ... that fails after about a min of trying (and i have plenty of HD space). The only way to fix this issue, is to manually stop the www service and then start it again. The stopping takes a while (a minute?) while starting is nearly instant. I'm at a loss to figure out what part of my code is causing this. At first, I thought it might be a stack overflow because of some error that might be going to the error page, which in turn errors .. rinse repeat boom. But i've had a look at the error page and it feels ok. So, I'm hoping someone might be able to help and say how I can correctly get a proper dump of the IIS process so i can then do some more autopsy on it. I would email Tess Ferrandez (the goddess of crash debuging) but I thought I'd try here before I spam her. Can anyone have any suggestions to how I can figure out how to start to debug this issue?

  Read the article

• XP box with 3 NICs on Server 2003 Domain

  - by Hannibal

  I have assigned all three NICs IP addresses that are outside the DHCP pool. I have 2 NICs are connected to 1 switch and the 3rd to my second switch. I want to assign one of the two NICs on the 1st switch to "normal" network activity (e.g. internet access, RDP, etc.) The other two NICs I want to reserve for mirroring ports on their respective switches. While this machine is connected to the domain I can access the internet and Remote Desktop. I have no idea which NIC I am using until I start mirroring a port, at which time, if I happen to be connected through one of the NICs I have dedicated to mirroring, I lose my remote desktop. I am aware that I would have more control over the NICs using Linux. I want to explore Windows solutions before I go that route because reinstalling another OS would be inconvenient (but not impossible). I would likely use a version of Backtrack (3 or 4 not sure). I would also have to learn how to access the machine remotely but I've done it before so this would be a minor obstacle. Thank you for your assistance.

  Read the article

• Generalized strategy for file server virtualization in Xenserver

  - by Jamie

  I'm not shopping as much as I'm looking for some guidance on good idea / bad idea strategies. I'm sure I'm not in the "best practices" budget range. Currently, I have 3 dell poweredges running xenserver in a pool. Each node has a ubuntu file server, serving about 6TB. One is the primary, the other two are rsync targets for backup. The 6TB is stored on their respective local storage disks as an LVM of 3x2tb virtual disks. The fileserver VM disks are also stored on the node local disks. Each node also runs a smattering of light-weight VMs for web, development, windows VMs, and stuff like that. Several of those VM's disks reside on a QNAP NAS to play with live migration. These VM's are often clients of the primary file server (like all the mail, web content, user files are stored on the file server, not on the mail, web, and samba VMs). This all works fine, and is a major step up for us. The downside is that the QNAP is a single point of failure. And the only thing the QNAP is doing is serving migratable VM images, not client data. Someday the poweredge local arrays will be full, and we will have to reinvent ourselves again. Is it wise to have heavywieght vms (like the fileserver, with its 6+ TB disks) on a SAN or NAS? Would it be better to keep the VMs lightweight, have the VM images on a SAN or NAS, and use 2 or more NAS act as NFS-serving file appliances? A hybrid SAN/NAS that can serve iscsi for images and NFS for the client vms? It seems like live-magration would be a misnomer if you have to migrate a fileserver with its entire 6+ TB disk. I recognize there are plenty of ways to skin the cat. We've already skinned it a few ways. What makes sense?

  Read the article

• Login failed for user 'XXX' on the mirrored sql server

  - by hp17

  Hello, We have 4 web servers that host our asp.net (3.5) application. Randomly, we get error messages like : 1) "Login failed for user 'userid'" 2) "A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)" we are running sql2005 and have a principle and a mirror db (sync). When these exceptions are thrown, I look at the SQL error logs on the mirrored db and noticed the failed login messages in there. The principle db is running fine and the other web apps are working great. this will happen for maybe 10 min, then the app pool recycles and it starts hitting the principle db again. Is there a configuration I have incorrect? my theory is that our principle db is forwarding the request to the mirror, but that should never happen. any help??

  Read the article

• DD-WRT Acces Point as a Router

  - by Dzh

  Following suggestion to this question asked on Network Engineering, I am asking the question here. this is an extension to my previous question (I think it was deleted), where I was claiming that DDWRT was disabling it's DHCP server once connected to the network. I was wrong, as it now seems that it is bridging itself with another parallel connected wireless router. I have two Draytek 2820 and one Netgear WG602v3 with latest DDWRT. Lets call one wired-Draytek and it has wireless disabled. The other one, let's call it wireless-Draytek, is connected to wired-Draytek and has wireless with MAC filtering enabled. Once I connect Netgear to the wired-Draytek, the client that connects to Netgear, will be assigned with IP address from the wireless-Draytek. If the MAC address is not on the wireles-Draytek, the client is unable to obtain IP address and has no connectivity at all, even with manually assigned static IP configuration. To illustrate further, this is how network is set up: wired-Draytek ---------- wireless-Draytek \_________ Netgear What I wish to have, is that Netgear issues IP addresses from it's own IP pool and ignores the MAC filtering rules from wireless-Draytek. This is kind of puzzling how this they are bridging (if they are) themselves automatically. Thanks. UPDATE: It's not a home network. I gave you a bit simplified set-up. If there is a better site on Stack Exchange to ask this, please let me know. The Drayteks are running stock firmware, it's only Netgear that I've flashed to get more stability. In addition to these routers, I have also three 3COM Baseline switch 2824, and another Draytek router with Prosafe FS752TP PoE switch dedicated for VoIP phones. Wired-Draytek has IP 10.0.0.1, DHCP disabled as there is AD DC which is issuing IP addresses. Wireless-Draytek has IP 1.1.1.1 and DHCP enabled. Netgear has default - 192.168.1.1. As per suggestion, the specific question is - how do I isolate these two wireless routers?

  Read the article

• Cisco ASA user authentication options - OpenID, public RSA sig, others?

  - by Ryan

  My organization has a Cisco ASA 5510 which I have made act as a firewall/gateway for one of our offices. Most resources a remote user would come looking for exist inside. I've implemented the usual deal - basic inside networks with outbound NAT, one primary outside interface with some secondary public IPs in the PAT pool for public-facing services, a couple site-to-site IPSec links to other branches, etc. - and I'm working now on VPN. I have the WebVPN (clientless SSL VPN) working and even traversing the site-to-site links. At the moment I'm leaving a legacy OpenVPN AS in place for thick client VPN. What I would like to do is standardize on an authentication method for all VPN then switch to the Cisco's IPSec thick VPN server. I'm trying to figure out what's really possible for authentication for these VPN users (thick client and clientless). My organization uses Google Apps and we already use dotnetopenauth to authenticate users for a couple internal services. I'd like to be able to do the same thing for thin and thick VPN. Alternatively a signature-based solution using RSA public keypairs (ssh-keygen type) would be useful to identify user@hardware. I'm trying to get away from legacy username/password auth especially if it's internal to the Cisco (just another password set to manage and for users to forget). I know I can map against an existing LDAP server but we have LDAP accounts created for only about 10% of the user base (mostly developers for Linux shell access). I guess what I'm looking for is a piece of middleware which appears to the Cisco as an LDAP server but will interface with the user's existing OpenID identity. Nothing I've seen in the Cisco suggests it can do this natively. But RSA public keys would be a runner-up, and much much better than standalone or even LDAP auth. What's really practical here?

  Read the article

• Php5-fpm Crash if much visitors

  - by chillah

  I decided to change my OP to Nginx from Litespeed because i read much about the low resource that Nginx would cost. Im running a Wordpress site with 500 users online My www.conf in "/etc/php5/fpm/pool.d" pm.max_children = 200 pm.start_servers = 20 pm.min_spare_servers = 20 pm.max_spare_servers = 60 ;pm.process_idle_timeout = 10s; ;pm.max_requests = 1000 Since i changed that config to higher requests and more children the Site needs longer till it shows me a White blank page. If i restart the php5-fpm prozess then, the site is running fine again. The CPU usage is at 5% if the php5-fpm is crashed and if its running its about 20 to 90%! Heres my Nginx.conf: user www-data; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 3048; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; I already tried changing the settings, tryed all variants but nothing worked. The Mashine: Dualcore 4gb ram

  Read the article

• How to configure traffic from a specific IP hardcoded to an IP to forward to another IP:PORT using i

  - by cclark

  Unfortunately we have a client who has hardcoded a device to point at a specific IP and port. We'd like to redirect traffic from their IP to our load balancer which will send the HTTP POSTs to a pool of servers able to handle that request. I would like existing traffic from all other IPs to be unaffected. I believe iptables is the best way to accomplish this and I think this command should work: /sbin/iptables -t nat -A PREROUTING -s $CUSTIP -j DNAT -p tcp --dport 8080 -d $CURR_SERVER_IP --to-destination $NEW_SERVER_IP:8080 Unfortunately it isn't working as expected. I'm not sure if I need to add another rule, potentially in the POSTROUTING chain? Below I've substituted the variables above with real IPs and tried to replicate the layout in my test environment in incremental steps. $CURR_SERVER_IP = 192.168.2.11 $NEW_SERVER_IP = 192.168.2.12 $CUST_IP = 192.168.0.50 Port forward on the same IP /sbin/iptables -t nat -A PREROUTING -p tcp -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.11:8080 Works exactly as expected. IP and port forward to a different machine /sbin/iptables -t nat -A PREROUTING -p tcp -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.12:8080 Connections seem to timeout. Restrict IP and port forward to only be applied to requests from a specific IP /sbin/iptables -t nat -A PREROUTING -p tcp -s 192.168.0.50 -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.12:8080 Times out as well. Probably for the same reason as the previous entry. Does anyone have any insights or suggestions? thanks,

  Read the article

• SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database

  - by eulerfx

  I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• Openvpn - stuck on Connecting

  - by user224277

  I've got a problem with openvpn server... every time when I trying to connect to the VPN , I am getting a window with login and password box, so I typed my login and password (login = Common Name (user1) and password is from a challenge password from the client certificate. Logs : Jun 7 17:03:05 test ovpn-openvpn[5618]: Authenticate/Decrypt packet error: packet HMAC authentication failed Jun 7 17:03:05 test ovpn-openvpn[5618]: TLS Error: incoming packet authentication failed from [AF_INET]80.**.**.***:54179 Client.ovpn : client #dev tap dev tun #proto tcp proto udp remote [Server IP] 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert user1.crt key user1.key <tls-auth> -----BEGIN OpenVPN Static key V1----- d1e0... -----END OpenVPN Static key V1----- </tls-auth> ns-cert-type server cipher AES-256-CBC comp-lzo yes verb 0 mute 20 My openvpn.conf : port 1194 #proto tcp proto udp #dev tap dev tun #dev-node MyTap ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/VPN.crt key /etc/openvpn/keys/VPN.key dh /etc/openvpn/keys/dh2048.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt #push „route 192.168.5.0 255.255.255.0? #push „route 192.168.10.0 255.255.255.0? keepalive 10 120 tls-auth /etc/openvpn/keys/ta.key 0 #cipher BF-CBC # Blowfish #cipher AES-128-CBC # AES #cipher DES-EDE3-CBC # Triple-DES comp-lzo #max-clients 100 #user nobody #group nogroup persist-key persist-tun status openvpn-status.log #log openvpn.log #log-append openvpn.log verb 3 sysctl : net.ipv4.ip_forward=1

  Read the article

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• Problem running “Central Administration” website after windows update at Windows 2003 Server Standar

  - by Magdy Roshdy

  I was have WSS 2.0 and then I upgraded to WSS 3.0 and the old instalation database was SQL 2000, now I have another SQL Server instance called:server_name\MICROSOFT##SSEE . After upgrade every thing works fine and our team started to use the portal and we sent lot of documents and make lot of activities on it. The problem started after installing Windows updates the website suddenly stopped and giving me an error "Cannot connect to the configuration database" If I tried to open SharePoint Products and Technologies Configuration Wizard it is gives me a strange error says: "An exception of type Microsoft.SharePoint.PostSetupConfiguration.PostSetupConfigurationTaskException was thrown. Additional exception information: SharePoint Products and Technologies cannot be configured. The current installation mode does not support SKU to SKU upgrades because there exists an older version of Windows SharePoint Services that must be upgraded first " At this post:http://stackoverflow.com/questions/114398/iis-error-cannot-connect-to-the-configuration-database/249494#249494 the guy of the second answer have the same problem and he suggested a solution but I don't understand well. I tried as he suggested to make the identity of the app pool of the SharePoint web site as "IWAM_server_name " after that the error changed as he said and I web site give me "Server Application Unavailable " and when checked the Event Viewer at the server I found that ASP.NET 2.0 give this exception: "Could not load file or assembly 'System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' or one of its dependencies. Access is denied ." and I don't know how to solve this problem. I'm really want to make my web site working because our team really need these documents and its stuff. I hope I will find some one to help me.

  Read the article

• F5 BIG_IP persistence iRules applied but not affecting selected member

  - by zoli

  I have a virtual server. I have 2 iRules (see below) assigned to it as resources. From the server log it looks like that the rules are running and they select the correct member from the pool after persisting the session (as far as I can tell based on my log messages), but the requests are ultimately directed to somewhere else. Here's how both rules look like: when HTTP_RESPONSE { set sessionId [HTTP::header X-SessionId] if {$sessionId ne ""} { persist add uie $sessionId 3600 log local0.debug "Session persisted: <$sessionId> to <[persist lookup uie $sessionId]>" } } when HTTP_REQUEST { set sessionId [findstr [HTTP::path] "/session/" 9 /] if {$sessionId ne ""} { persist uie $sessionId set persistValue [persist lookup uie $sessionId] log local0.debug "Found persistence key <$sessionId> : <$persistValue>" } } According to the log messages from the rules, the proper balancer members are selected. Note: the two rules can not conflict, they are looking for different things in the path. Those two things never appear in the same path. Notes about the server: * The default load balancing method is RR. * There is no persistence profile assigned to the virtual server. I'm wondering if this should be adequate to enable the persistence, or alternatively, do I have to combine the 2 rules and create a persistence profile with them for the virtual server? Or is there something else that I have missed?

  Read the article

• Installing ionCube on Windows 2008 64bit

  - by JoJo

  I've been trying to install ionCube onto my server but have not been having a lot of luck! My server is: Windows 2008 64bit PHP 5.3.14 Thread Safe disabled running as FastCGI In my PHP.ini I have : zend_extension="C:\Program Files (x86)\PHP\ext\ioncube_loader_win_5.2.dll" The path is correct. The DLL is from the x86 NONTS VC9 version of ionCube and PHP is using the MSVC9 (Visual C++ 2008) compiler though I have also tried using the x86 NONTS VC6 version of ionCube. I'm not getting any error but I'm also not getting ionCube when using phpinfo(): This program makes use of the Zend Scripting Language Engine: Zend Engine v2.3.0, Copyright (c) 1998-2012 Zend Technologies Apart from the mail application pools I have also set all the applications in the application pool in IIS7 to use 32bit mode. I don't know if FastCGI is running under 64 or 32 bit mode nor how to switch it or whether it would make a difference? I know it can be a problem installing ionCube onto 64bit Windows but I have also come across threads whereby other people have also [somehow] managed to get it working but even though I seem to be doing the same as them I still can't get it working.

  Read the article

• Fortigate restrict traffic through one external IP

  - by Tom O'Connor

  I've got a fortigate 400A at a client's site. They've got a /26 from British Telecom, and we're using 4 of those IPs as a NAT Pool. Is there a way to say that traffic from 172.18.4.40-45 can only ever come out of (and hence go back into) x.x.x.140 as the external IP? We're having some problems with SIP which looks like it's coming out of one, and trying to go back into another. I tried enabling asymmetric routing, didn't work. I tried setting a VIP, but even when I did that, it didn't appear to do anything. Any ideas? I can probably post some firewall snippets if need be.. Tell me what you want to see. SIP ALG config system settings set sip-helper disable set sip-nat-trace disable set sip-tcp-port 5061 set sip-udp-port 5061 set multicast-forward enable end Interesting Sidenote VoIP phones, with no special configuration can register fine to proxy.sipgate.co.uk, which has an IP address of 217.10.79.16. Which is cool. Two phones are using a different provider, whose proxy IP address is 178.255.x.x. These phones can register for outbound, but inbound INVITEs never make it to the phone. Is it possible that the Fortigate is having trouble with 178.255.x.x as it's got a 255 in it? Or am I just imagining things?

  Read the article

• Unable to ssh in Beagle Bone Black

  - by SamuraiT

  I wanted to install pip onto beagle bone black,and I tried this: /usr/bin/ntpdate -b -s -u pool.ntp.org opkg update && opkg install python-pip python-setuptools then, it threw errors,but Unfortunately, I didn't log that errors. it was occurred a week ago and was't solved yet. I wanted to solve it now and I tried connect by ssh,but I failed. When I ping to beagle bone, it responds, and Cloud9 IDE is working too but not ssh. I don't think this is serious problem since I can connect to beagle bone by other methods: Cloud9 or so. However, to use python on beagle bone, I need to connect by ssh. Before trying to update and install python-pip, I could connect by ssh. Do you have any ideas to solve this connection problem? note I use default OS: Angstrom I don't use SD card. HOST PC is mac, OS.X 10.9 connect by USB serial I checked this but this wasn't helpful http://stackoverflow.com/questions/19233516/cannot-connect-to-beagle-bone-black I could connect by GateOne SSH client, but still unable to connect from terminal.

  Read the article

• 32bit dll not loading with Enable 32 Bit Applications on IIS 7.5

  - by Jon

  I have a MVC 3 Web Site referencing a 32 bit DLL. The OS is Windows 2008 R2 x64. The website is in the ASP.NET 4 App Pool. I have turned on Enable32Bit but it doesn't work. I get a Bad Image Exception but can't find out to turn this level of logging on in IIS. I have setup up a page that outputs whether it's running 32bit or 64bit and when I turn on/off the Enable32Bit on the AppPool I get the correct output. The website is also in Full Trust. I'm at a loss to try and and get it to work. I do know that it works on Win7 32bit. Can you suggest some things to try? UPDATE: I have just written a simple Windows Forms App with a button on it which calls my DLL. This was built with target of x86 and it worked fine so there is an issue with IIS or ASP.Net I think. UPDATE 2: Does it matter if the ASP.Net Pipeline is Clasic or Integrated? I've tried both but same problem but thought it was worth asking UPDATE 3: I found this question trying to do the same thing and he gave up which isnt too helpful!!

  Read the article

• ASP.Net Session Timing Out Rapidly

  - by Zac

  We have an ASP.Net 3.5 website running on Windows Server 2008 with IIS7. The session timeout period for this site is configured to be 20 minutes - however, it is currently lasting for between 40 and 50 seconds. After researching the problem we investigated several configuration values which could be involved in the timeout period but none of them are set to less than 20 minutes. The areas we look are as follows: web.config system.web/sessionState element (20 minutes). web.config system.web/authentication/forms element (not present, defaults to 30 minutes). Sites/{website}/ASP/Session Properties/Time-out (20 minutes). Application Pools/{appPool}/Advanced Settings/Process Model/Idle Time-out (20 minutes). We've also noted that the CPU is staying around 0% and that RAM usage is flat-lining around 1.07 GB (of 8 GB available) - so there is no performance-based reason for IIS to be recycling the Application Pool as far as we can tell. Are there any settings we've overlooked which could cause the session timeouts to be expiring so quickly? EDIT A couple of additional points: This is not occurring in development, only on the server. The session is not sliding (i.e. if we refresh the page a few times it still times out approximately 40 - 50 seconds after the session was created.

  Read the article

• IIS 7 much slower than IIS 6

  - by JoeJoe

  I have a asp.net 3.5 web application running fine on Windows2003 IIS6. I published same exact application to IIS7.5 (Win2008R2) on a faster box (i5,8Gram) and it is significantly slower. 5-6 sec per page vs. 1-2 sec per page. During that time the Task Mgr CPU is always under 10%. Both attach to same database on other box. Benchmark is consistent from any other client browser or machine. I have connection pool on both, compression on both. Same network subnet. Forms authentication (no SSL yet). Can you give me steps on how to troubleshoot where the delays are being inserted or settings in IIS7 that I may have overlooked. Just using defaults. There is only 1 web site on each box. I understand the roles of an Application as defined in IIS has changed. There is no special Application defined in IIS.

  Read the article

• Cannot destroy ZFS snapshot: dataset already exists

  - by Morven

  I have a server (T5220, though I doubt it matters) running Solaris 10 8/07 and I have a ZFS pool, "mysql", on internal disk. Within it I have a filesystem "mysql/data/4.1.12", which I snapshot hourly with a script from cron. I have one snapshot, created as one of those hourly snaps, that will not destroy. I have renamed it out of sequence to be "mysql/data/4.1.12@wibble" so that my script will not try and fail to destroy it, but it was originally within the sequence, though I doubt that matters. It renames successfully. The snapshot can be successfully navigated and read from through the .zfs/snapshots directory. It has no clones based on it. Trying to destroy it does this: (265) root@web-mysql4:/# zfs destroy mysql/data/4.1.12@wibble cannot destroy 'mysql/data/4.1.12@wibble': dataset already exists (266) root@web-mysql4:/# which is apparently nonsensical: of course it already exists, that's the point! Anyone seen anything like this before? Web searches show nothing obviously similar. I can provide patches installed if necessary.

  Read the article

• OpenVPN server will not redirect traffic

  - by skerit

  I set up an OpenVPN server on my VPS, using this guide: http://vpsnoc.com/blog/how-to-install-openvpn-on-a-debianubuntu-vps-instantly/ And I can connect to it without problems. Connect, that is, because no traffic is being redirected. When I try to load a webpage when connected to the vpn I just get an error. This is the config file it generated: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca ca.crt cert server.crt key server.key dh dh1024.pem push "route 10.8.0.0 255.255.255.0" push "redirect-gateway" comp-lzo keepalive 10 60 ping-timer-rem persist-tun persist-key group daemon daemon This is my iptables.conf # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *raw :PREROUTING ACCEPT [37938267:10998335127] :OUTPUT ACCEPT [35616847:14165347907] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *nat :PREROUTING ACCEPT [794948:91051460] :POSTROUTING ACCEPT [1603974:108147033] :OUTPUT ACCEPT [1603974:108147033] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth1 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j MASQUERADE COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *mangle :PREROUTING ACCEPT [37938267:10998335127] :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616847:14165347907] :POSTROUTING ACCEPT [35680187:14169930490] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *filter :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616848:14165347947] -A INPUT -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A FORWARD -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 -A FORWARD -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A OUTPUT -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 COMMIT # Completed on Sat May 7 13:09:44 2011

  Read the article

< Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >