Search Results

Search found 4503 results on 181 pages for 'logical operator'.

Page 72/181 | < Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >

  • ipmi - can't ping or remotely connect

    - by Fidel
    I've tried configuring the IPMI controller to accept remote connections, but I can't even ping it. Here is it status: #/usr/local/bin/ipmitool lan print 2 Set in Progress : Set Complete Auth Type Support : NONE PASSWORD Auth Type Enable : Callback : : User : NONE PASSWORD : Operator : PASSWORD : Admin : PASSWORD : OEM : IP Address Source : Static Address IP Address : 192.168.1.112 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:67:45:25 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Enabled Gratituous ARP Intrvl : 8.0 seconds Default Gateway IP : 192.168.1.1 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 0,1,2,3 Cipher Suite Priv Max : uaaaXXXXXXXXXXX : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM # /usr/local/bin/ipmitool user list 2 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Limit 1 true false true true USER 2 admin true false true true ADMINISTRATOR # /usr/local/bin/ipmitool channel getaccess 2 2 Maximum User IDs : 5 Enabled User IDs : 2 User ID : 2 User Name : admin Fixed Name : No Access Available : callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR # /usr/local/bin/ipmitool channel info 2 Channel 0x2 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available # /usr/local/bin/ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : unknown Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false # arp Address HWtype HWaddress Flags Mask Iface 192.168.1.112 ether 00:A0:A5:67:45:25 C bond0 # /usr/local/bin/ipmitool -I lan -H 192.168.1.112 -U admin -P admin chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status In summary. It exists on the ARP list so arp's are being broadcast. I can't ping it and can't connect to it. Can anyone spot any glaring mistakes in the configuration? Many thanks, Fidel

    Read the article

  • Cannot load from raid with grub

    - by Andrew Answer
    I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... This is my partial fdisk -l output: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Anybody can resolve this issue? I have big headache with this.

    Read the article

  • Allignment of ext3 partition on LVM RAID volume group

    - by John P
    I'm trying to add a partition on a LVM that resides on a RAID6 volume group and fdisk is complaining about the partition not residing on a physical sector boundry. My question is, how do you calculate the correct starting sector for a partition on a LVM? This partition will be formated ext3. Would it be better to just format the LVM directly instead of creating a new partition? Disk /dev/dedvol/backup: 2199.0 GB, 2199023255552 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 1048576 bytes / 8388608 bytes Disk identifier: 0x4e428f49 Device Boot Start End Blocks Id System /dev/dedvol/backup1 63 267349 2146982827+ 83 Linux Partition 1 does not start on physical sector boundary. lvdisplay /dev/dedvol/backup --- Logical volume --- LV Name /dev/dedvol/backup VG Name dedvol LV UUID OV2n5j-7LHb-exJL-t8dI-dU8A-2vxf-uIicCt LV Write Access read/write LV Status available # open 0 LV Size 2.00 TiB Current LE 524288 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 32768 Block device 253:1 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 3 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 14.55 TiB PE Size 4.00 MiB Total PE 3815448 Alloc PE / Size 3670016 / 14.00 TiB Free PE / Size 145432 / 568.09 GiB VG UUID 8fBcOk-aXGx-P3Qy-VVpJ-0zK1-fQgy-Cb691J

    Read the article

  • EMC VNX iSCSI setup - unsure about SP/port assignment

    - by pauska
    We have a new VNX5300 waiting to get configured, and I need to plan out the network infrastructure before the EMC tech arrives. It has 4x1gbit iSCSI per SP (8 ports in total), and I'd like to get the most out of the performance until we jump over to 10gig iSCSI. From what I can read from the docs - the recommendation is to use only two ports per SP, with 1 active and 1 passive. Why is this? It seems kind of pointless to have quad-port i/o-modules and then recommend to not use more than two of them? Also - I'm a bit unsure about the zoning. The best practices guide state that you should separate each port on each SP from each other on different logical networks. Does this mean that I have to create 4 logical networks to be able to use all 8 ports? It also gives the following example: Does this mean that A0 and B0 should sit on the same physical switch aswell? Won't this make all traffic go on one switch (if both A1 and B1 are passive)? Edit: Another brainpuzzle I don't get it - each host (as in server) should not have more iSCSI bandwidth available than the storage processor. What on earth does this matter? If serverA have 1gbit and serverB have 100mbit, then the resulting bandwith between them is 100mbit. How can this result in some kind of oversubscription? Edit4: Wait, what. Active and passive ports? The VNX runs in a ALUA configuration with asymmetrical active/active.. there shouldn't be any passive ports, only preferred ones..

    Read the article

  • Ubuntu 12.04/12.10 can't detect windows or any other partitions(Asus z77 UEFI BIOS)

    - by user971155
    I've recently completed tinkering my new pc(motherboard ASUS z77 with UEFI BIOS) and unfortunately not everything works quite well. After installing windows 7 ultimate on a single primary partition(SATA drive) I decided to allocate one more logical partition for additional needs. When I tried doing it with the manager - it said that it couldn't allocate requested size even though I certainly asked for much less than it was available. I thought that it might have been a windows issue and proceded to installing Ubuntu 12.10 x64. When the graphical interface loaded it showed me a message stating that it can't find any other operating system on the drive. When I used custom partioning option it showed me none of my current partions(including that with windows). However, when I boot with "Try Ubuntu" feature it does find them ! I find it weird though. Here's what the console present me with: ubuntu@ubuntu:~$ sudo os-prober /dev/sda1:Windows 7 (loader):Windows:chain ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00072b98 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 100020223 49906688 7 HPFS/NTFS/exFAT /dev/sda3 100022270 1250263039 575120385 5 Extended /dev/sda4 566669312 1250263039 341796864 83 Linux I also tried creating partitions from disk utility which results in error: , Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=51211402240, size=1923000000, type=0x83 Entering MS-DOS parser (offset=0, size=640135028736) MSDOS_MAGIC found looking at part 0 (offset 1048576, size 104857600, type 0x07) new part entry looking at part 1 (offset 105906176, size 51104448512, type 0x07) new part entry looking at part 2 (offset 51211402240, size 588923274240, type 0x05) Entering MS-DOS extended parser (offset=51211402240, size=588923274240) readfrom = 51211402240 MSDOS_MAGIC found Exiting MS-DOS extended parser looking at part 3 (offset 290134687744, size 349999988736, type 0x83) new part entry Exiting MS-DOS parser MSDOS partition table detected containing partition table scheme = 1 got it Error: Can't have overlapping partitions. ped_disk_new() failed Here's what I get when I try to install the system i.stack.imgur.com/pjlb9.png, i.stack.imgur.com/g1lXN.png P.S. It's strange that I even can't create any more partitions neither with disk-utility nor with windows 7 native tools

    Read the article

  • Recover data from Dynamic Disk (MBR) bigger than 2TB

    - by Helder
    Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

    Read the article

  • VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

    - by Dayton Brown
    I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

    Read the article

  • why does the partition start on sector 2048 instead of 63

    - by gcb
    I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

    Read the article

  • Multiple servers vs 1 big server performace

    - by pistacchio
    Hi to all! My team of developers has suggested a server structure for an upcoming project we are developing. Our structure is "logical", meaning that the various logical components of the application (it is a distributed one) relies on different servers. Some components are more critical than others and will be subjected to more load. Our proposal was to have 1 server per component but the hardware guys suggested to replace the various machines with a single, bigger one with virtual servers. They're gonna use Blade Servers. Now, I'm not an expert at all, but my question to the guys was: so if we need, for example, 3 2GHz CPU / 2GB RAM machines and you give me 1 machine with 3 2GHz CPUs and 6 GB of RAM it is the same? They told me it is. Is this accurate? What are the advantages or disadvantages of both the solutions? What are the generally accepted best practices? Could you point out some URL reference dealing with the problem? Thank you in advance! EDIT: Some more info. The (internet / intranet) application is already layered. We have some servers on the DMZ that will expose pages to the internet and the databases are on their own machines. What we want to split (and they want to join) are some webservers that mainly expose webservices. One is a DAL that communicates with the database layer, one is our Single Sign On / User Profile application that gets called once per page and one is a clone of what seen on the Internet to be used on our lan.

    Read the article

  • Ubuntu 10.04 network manager issues

    - by Shark
    I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

    Read the article

  • IBM BladeCenter S: Disk Configuration

    - by gravyface
    Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

    Read the article

  • Extending ext4 partition on debian7.0 on vsphere

    - by VoidPointer
    I have allocated thin provisioning of 15GB when i found 8GB as insufficient. Now debian guest is not able to recognize the change of size. root@debian7-x64:~# lvdisplay --- Logical volume --- LV Path /dev/debian7-x64/root LV Name root VG Name debian7-x64 LV UUID EU6mg0-XTXC-ci3D-bQJi-7XN6-r8Hp-SYxcj0 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 1 LV Size 7.39 GiB Current LE 1892 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:0 --- Logical volume --- LV Path /dev/debian7-x64/swap_1 LV Name swap_1 VG Name debian7-x64 LV UUID xDNtoz-tJUq-M5D6-GGCN-gzcD-fwUv-fYYDR1 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 2 LV Size 376.00 MiB Current LE 94 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:1 root@debian7-x64:~# pvdisplay --- Physical volume --- PV Name /dev/sda5 VG Name debian7-x64 PV Size 7.76 GiB / not usable 2.00 MiB Allocatable yes (but full) PE Size 4.00 MiB Total PE 1986 Free PE 0 Allocated PE 1986 PV UUID SehkzH-Gq8Y-jI2f-27Tb-uv1Z-tR1R-5OnTxR root@debian7-x64:~# sfdisk -s /dev/sda: 15728640 /dev/mapper/debian7--x64-root: 7749632 /dev/mapper/debian7--x64-swap_1: 385024 total: 23863296 blocks Help me to extend this partition. No problem in rebooting. I dont have any live CD. Environment : debian 7, with lvm, on vsphere, ext4 partition. Can provide more details when needed.

    Read the article

  • P2V Wouldn't Boot, Rebuilt initrd, Need to Clean Up

    - by Mike Soule
    We have a CentOS 5.4 server (build 2.6.18-164.el5xen). We went to P2V this server so we can have redundancy, the physical only has one PSU. The P2V only completed 99% of the way, we have a VMWare ticket opened, but they marked the ticket as low priority. I was able to boot into a rescue disc of Red Hat 5.4 and rebuild the initrd with the help of this blog post. Now the only issue is the original server had a modified initrd, which was also from a different OS build and made by an outside provider. We do not have a document outlining modifications. My question is, is it at all possible to copy the initrd off of the physical server and replace it on the virtual and some how have the virtual machine boot? Thanks for any input. Edit: I copied the initrd img from the physical and it recreated the original issue. Here is a screen capture of the error. http://i.imgur.com/MqC73.jpg Edit2: echo Scanning logical volumes lvm vgscan --ignorelockingfailure echo Activating logical volumes lvm vgchange -ay --ignorelockingfailure VolGroup00 resume /dev/VolGroup00/LogVol01 echo Creating root device. mkrootdev -t ext3 -o defaults,ro /dev/VolGroup00/LogVol00 echo Mounting root filesystem. mount /sysroot

    Read the article

  • Boot records messed on dual boot (win7 and ubuntu) machine with SSD and HDD

    - by Michael
    i have a lenovo ideapad y570 with two hard drives: SSD and normal HDD both managed by RapidDrive and windows 7 pre-installed. First, i have shrunk my 500 GB HDD a little bit to make some place for a linux installation. Then i installed linux mint 12 to it, also installed grub onto the drive (dev/sdb). Installation programm has not allowed me to install grub on sda. Then i replaced linux mint with ubuntu 12.04 but installed grub onto the SSD (which is dev/sda and was the default-option). After that i could boot into my windows, only ubuntu worked. So i did a research, and tried: rewriting mbr of windows into sda1, reinstalling grub, replacing grub2 with grub-legacy, and now i think my partitions table are totally messed. Here is fdisk -l output: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 * 2048 411647 204800 7 HPFS/NTFS/exFAT /dev/sda2 411648 1009430959 504509656 7 HPFS/NTFS/exFAT Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x5e5d1cc8 Device Boot Start End Blocks Id System /dev/sdb1 * 1979 884389887 442193954+ 12 Compaq diagnostics /dev/sdb2 884391934 976771071 46189569 5 Extended /dev/sdb5 884391936 937705471 26656768 83 Linux /dev/sdb6 937707520 967006207 14649344 83 Linux /dev/sdb7 967008256 976771071 4881408 82 Linux swap / Solaris I also cant mount any windows partitions to recover data. And when i open gparted, the whole sda-disk appears unallocated and it states "can not have a partition outside the disk!", also the end-sector address of /dev/sda2 confuses me. If i boot from the SSD, it throws some mbr error and wont boot, if i boot from the HDD, i only get the grub bash. How do i restore the partition tables? I can boot only from a live-cd at the machine. Thanks for any help.

    Read the article

  • Triple-Boot + 4 partition Limit

    - by dsimcha
    I just bought a new hard drive so that I could convert my XP-only machine into an XP-Ubuntu-Windows 7 triple boot machine. Since the drive is absurdly huge (1 TB) I wouldn't mind throwing ReactOS into the mix, too. I just found out that master boot records are limited to 4 entries, meaning 4 primary partitions. I had Windows XP set up on my old drive as a boot partition, a program files partition and a media partition. Since I really didn't want to install XP from scratch, I cloned this setup on my new drive. This leaves me one MBR partition entry for installing Windows 7, Ubuntu and ReactOS. I'd like to avoid having to install XP from scratch like the plague, partly because it's supposed to be a safety net in case things go wrong with my other OS's and because I've invested a lot of time getting it set up exactly the way I like it. Here are the options I've considered and why I don't like them: Install Windows 7 on my media partition. This would work, but I prefer to keep my media partition completely separate from any OS, so that I can reformat an OS partition without affecting my media partition at all. Use wubi or something to install Ubuntu in the same partition as something else. Again, this is brittle. Move all my media to a logical drive on an extended partition. Create another logical drive on this extended partition for Ubuntu. The problem here is that extended partitions are rather brittle--if you nuke one, it renders the rest useless. Just put the old drive back in my computer and run XP off it. Use the new one for the other OS's. The problem here is that the old drive is slower and uses extra power, generates extra heat, etc. Can anyone suggest any other possibilities that I may have overlooked?

    Read the article

  • /etc/hosts: What is loghost? (fresh install of Solaris 10 update 9)

    - by cjavapro
    # # Internet host table # ::1 localhost 127.0.0.1 localhost XX.XX.XX.XX myserver loghost What is the purpose of loghost? If it was not for having loghost in there, all the /etc/hosts files on all the servers in this particular network could be identical. Edit: I looked at /etc/syslog.conf #ident "@(#)syslog.conf 1.5 98/12/14 SMI" /* SunOS 5.0 */ # # Copyright (c) 1991-1998 by Sun Microsystems, Inc. # All rights reserved. # # syslog configuration file. # # This file is processed by m4 so be careful to quote (`') names # that match m4 reserved words. Also, within ifdef's, arguments # containing commas must be quoted. # *.err;kern.notice;auth.notice /dev/sysmsg *.err;kern.debug;daemon.notice;mail.crit /var/adm/messages *.alert;kern.err;daemon.err operator *.alert root *.emerg * # if a non-loghost machine chooses to have authentication messages # sent to the loghost machine, un-comment out the following line: #auth.notice ifdef(`LOGHOST', /var/log/authlog, @loghost) mail.debug ifdef(`LOGHOST', /var/log/syslog, @loghost) # # non-loghost machines will use the following lines to cause "user" # log messages to be logged locally. # ifdef(`LOGHOST', , user.err /dev/sysmsg user.err /var/adm/messages user.alert `root, operator' user.emerg * ) Very interesting. when shutting down,, alerts go to all users probably through *.emerg * Looking at ifdef, it seems that the first parameter checks to see if current machine is a loghost, second parameter is what to do if it is and third parameter is what to do if it is not. Edit: If you want to test a logging rule you can use svcadm restart system-log to restart the logging service and then logger -p notice "test" to send a test log message where notice can be replaced with any type such as user.err, auth.notice, etc.

    Read the article

  • Partition problem tyring to install window 7 starter

    - by ant2009
    Hello HP Mini 210 I am trying to install windows starter 7. Currently I have installed fedora 14 xfce. And I have allocated 24 GB NTFS for hard disk for the windows partition. My current partitions are as follows: /dev/sda2 97G 4.9G 91G 6% / tmpfs 494M 92K 494M 1% /dev/shm /dev/sda1 485M 68M 392M 15% /boot /dev/sda5 169G 26G 135G 16% /home I have created a boot USD to install windows starter 7. When the computer boots into the windows setup and I selected the partition I want to install windows on. I get the following message: "Setup was unable to create a new system partition or locate an existing system partition." This is setup displaying all my partitions: Disk 0 Partition 1 500MB 0 Primary Disk 0 Partition 2 97.7GB 0 Primary Disk 0 Partition 3 4GB 0 Primary Disk 0 Partition 4 171.3GB 0 Logical Disk 0 Partition 5 24.6GB 24.5 Logical <-- Trying install on this partition NTFS I have also tried to delete the partition in setup and create a new one. And also tried to format the partition. However, I still get the same error message. Many thanks for any advice,

    Read the article

  • Samba/Winbind issues joing to Active directory domain

    - by Frap
    I'm currently in the process of setting up winbind/samba and getting a few issues. I can test connectivity with wbinfo fine: [root@buildmirror ~]# wbinfo -u hostname username administrator guest krbtgt username [root@buildmirror ~]# wbinfo -a username%password plaintext password authentication succeeded challenge/response password authentication succeeded however when I do a getent I don't get any AD accounts returned [root@buildmirror ~]# getent passwd root:x:0:0:root:/root:/bin/bash bin:x:1:1:bin:/bin:/sbin/nologin daemon:x:2:2:daemon:/sbin:/sbin/nologin adm:x:3:4:adm:/var/adm:/sbin/nologin lp:x:4:7:lp:/var/spool/lpd:/sbin/nologin sync:x:5:0:sync:/sbin:/bin/sync shutdown:x:6:0:shutdown:/sbin:/sbin/shutdown halt:x:7:0:halt:/sbin:/sbin/halt mail:x:8:12:mail:/var/spool/mail:/sbin/nologin uucp:x:10:14:uucp:/var/spool/uucp:/sbin/nologin operator:x:11:0:operator:/root:/sbin/nologin puppet:x:52:52:Puppet:/var/lib/puppet:/sbin/nologin my nsswitch looks like this: passwd: files winbind shadow: files winbind group: files winbind #hosts: db files nisplus nis dns hosts: files dns and I'm definitely joined to the domain: [root@buildmirror ~]# net ads info LDAP server: 192.168.4.4 LDAP server name: pdc.domain.local Realm: domain.local Bind Path: dc=DOMAIN,dc=LOCAL LDAP port: 389 Server time: Sun, 05 Aug 2012 17:11:27 BST KDC server: 192.168.4.4 Server time offset: -1 So what am I missing?

    Read the article

  • Windows Server 2003 (w/Exchange) move to new machine

    - by James Booker
    I have an ageing domain controller (the only one on a 10-pc network) which needs rebooting often. I have a Dell Poweredge 2850 server doing nothing, so I'd like to move the DC to that, but here's the catch - I don't have Win2k Server Std install media any more as it's been lost. I purchased "Easus Todo Backup Advanced Server" which claims to be able to recover to dissimilar metal, but it's not quite working (although I don't think it's the product's fault) I know the server and PERC RAID card are good because I installed Ubuntu on the logical drive (4 x 72GB disks RAID 5) no problems. I've booted frmo the Easus Todo backup CD (which is WinPE based) and recovered to the logical disk on the RAID (after installing driver inside the WinPE environment from a NAS drive) The problem is when I boot the server, I can get the OS selection menu, but any option results in a blank screen, with no errors. I figure this is probably because the driver wasn't installed on the old machine (which is IDE-based (i know, i know!) and doesn;t have a RAID controller) I've booted from the CD and copied the mraid35x.sys file to the c:\windows\system32\drivers folder on the recovered system, but it makes no difference. I made a boot.ini with rdisks 0-10 defined, and booting from each of these resulted in a file error (i.e. 'this isn't a real disk') - the only disk that gets any response (the blank screen) is multi(0)disk(0)rdisk(0)partition(1) which just gives me the blank black screen and no disk activity. Is there any way I can force the drvier to be installed on the source system (so i can do a full backup again), i've tried right-clicking the oemsetup.inf and clicking install, but it didn't actually do anything. I attempted to force it with the 'Add new hardware' wizard and forcing with the 'have disk' option but it still gave me no hardware to select. Also I've got an identical machine running WinXP which uses the PERC driver successfully (which was obviously done at install time) and the boot.ini settings are the same : multi(0)disk(0)rdisk(0)partition(1) Any ideas would be appreciated.

    Read the article

  • Can't connect to wi-fi hotspot in Ubuntu 11.10

    - by ht3t
    I'm new to Ubuntu. I'm having a wireless network problem in Ubuntu 11.10. I made a hotspot using Connectify from a computer which is running Windows 7. I can access it in Windows 7 but not in Ubuntu 11.10. Every time I access it,I get a message "disconnected". I'm using msi fx 400 notebook with Intel Centrino wireless -N 1000 wireless card. Ubuntu version is 11.10 with KDE desktop. $ sudo lshw -c network [sudo] password for ht3t: *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:56:b8:f0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:44 memory:e7400000-e7401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 40:61:86:b6:b1:a2 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw IP=192.168.21.107 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:9000(size=256) memory:e6004000-e6004fff memory:e6000000-e6003fff I can't do anything without internet connection. How can I fix this?

    Read the article

  • mdadm lvm and ext4 slowness - How can I speed it up?

    - by beatbreaker
    I can't figure out why I'm getting such terrible times out of my mdadm and in particular the lvm partitions in it. I made the raid: mdadm --create --verbose /dev/md0 --level=5 --chunk=1024 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sda1[0] sdd1[3] sdc1[2] sdb1[1] 2930279424 blocks level 5, 1024k chunk, algorithm 2 [4/4] [UUUU] I then created the physical volume, volume group, and logical volumes, I then formatted the logical volumes to ext4 using the following commands I got from here: http://busybox.net/~aldot/mkfs_stride.html mkfs.ext3 -b 4096 -E stride=256,stripe-width=768 /dev/datavg/blah Now I'm confused, I had these lvs running real quick before in mdadm but now that I've 'optimized' everything it's slower, eg, before: /dev/datavg/lv_audio: Timing buffered disk reads: 598 MB in 3.01 seconds = 198.85 MB/sec but now after: /dev/datavg/audio: Timing buffered disk reads: 198 MB in 3.00 seconds = 65.96 MB/sec That's pitiful! What's happened here? Did I not follow the instructions correctly? Can i reshape the ext4 partitons to default back to what they were? (I used defaults before and they were fine!)

    Read the article

  • One Apache server, multiple clients - best practices for config files?

    - by OttaSean
    First time user; please be gentle. :-) (And if you don't like my question I'd be grateful for a comment as to why...) I am doing a contract at a government server shop that provides web services for multiple client groups in other areas of the government. My employer has asked me to look into how other shops, in similar situations, handle configuration files, and whether there are any best practices on the subject. I'm pretty sure there are lots of installations out there running multiple VirtualHosts out of one Apache installation, but surprisingly I couldn't find anything online about how people handle config file layout, so was hoping some of you wise folks on ServerFault might have some thoughts or pointers for me. The current setup - which seems logical to me - is that each client site has its own directory off the root - so: /client/tps-reports/ /client/silly-walks/ /client/ministry-of-magic/ and so on - and each of those directories has a /htdocs, /cgi-bin, and /conf (among others). The main /etc/apache/httpd.conf only contains Include statements (and lots of comments), the last of which is: Include /etc/apache/vhosts/*.conf The vhosts directory contains symlinks: tpsrept.conf - /client/tps-reports/conf/tpsrept.conf sillywk.conf - /client/silly-walks/conf/sillywk.conf mom.conf - /client/ministry-of-magic/mom.conf Each of those .conf files contains the actual NameVirtualHost definition and a gigantic <VirtualHost 192.168.12.34> stanza - which contains all the stuff about the specific site. The idea is that clients have access to what's in their own /client/xx directory, so they can change stuff in the section of the config that is relevant to them. As I mentioned above, that seems fairly logical to me, but I'm wondering if any of you wise folks are aware of potential gotchas with this sort of layout, or any other thoughts on why it is or isn't a good idea. In particular, how do other places do it? Is there a "best practice" for this sort of thing? Many thanks in advance for your time and any thoughts you all might have.

    Read the article

  • How can I extend / create a new partition from the following setup?

    - by Kiada
    I'm a little unsure what to do in this situation. When I try to create a new simple volume from the unallocated space I get an error because I already have 4 partitions. I have no option to extend either my C:\ primary partition or the E:\ logical drive. C:\ - Gaming Win7 install. D:\ - Storage Unallocated Space - Would somehow like to install OSX on a partition from this space. E:\ - Software Development Win7 install. I:\ - Ignore this. It's an external 1TB HDD. Do I have any options that do not involve formatting / losing information on either C:\ or E:\? Thank you. Link to visual disk partitioning setup image. Edit: A bit more information regarding partitions. Firstly, the image linked above is a screenshot of Windows 7 partitioning tool, easier to read than text I guess! H:\ System Reserved: 100MB NTFS C:\ 244 GB NTFS Healthy (Page File, Primary Partition) D:\ 294 GB NTFS Healthy (Primary Partition) E:\ 100 GB NTFS Healthy (Boot, Page File, Crash Dump, Logical Drive) Unallocated 292 GB Hope this helps :)

    Read the article

  • Debian boot problems

    - by psp
    I've got Debian server with one disk. No dual boot or anything fancy. Just Debian 6.0 (Squeeze). I rebooted the server today and now it doesn't boot. I get the following (from GRUB): error: hd0,msdos out of disk I then get a grub prompt grub rescue> I've been googling for ages with no luck. /etc/fstab > #/etc/fstab: static file system information. > # > # <file system> <mount point> <type> <options> <dump> <pass> > aufs / aufs rw 0 0 > tmpfs /tmp tmpfs nosuid,nodev 0 0 I've run debian rescue mode and looked through the syslog. I see hundreds of entries like this: Jun 30 22:51:08 kernel: [ 615.217382] sd 2:0:0:0: [sda] Unhandled error code Jun 30 22:51:08 kernel: [ 615.217385] sd 2:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK Jun 30 22:51:08 kernel: [ 615.217389] sd 2:0:0:0: [sda] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 Jun 30 22:51:08 kernel: [ 615.217399] end_request: I/O error, dev sda, logical block 0 Jun 30 22:51:08 kernel: [ 615.217402] Buffer I/O error on device sda, logical block 0

    Read the article

  • C++/boost generator module, feedback/critic please

    - by aaa
    hello. I wrote this generator, and I think to submit to boost people. Can you give me some feedback about it it basically allows to collapse multidimensional loops to flat multi-index queue. Loop can be boost lambda expressions. Main reason for doing this is to make parallel loops easier and separate algorithm from controlling structure (my fieldwork is computational chemistry where deep loops are common) 1 #ifndef _GENERATOR_HPP_ 2 #define _GENERATOR_HPP_ 3 4 #include <boost/array.hpp> 5 #include <boost/lambda/lambda.hpp> 6 #include <boost/noncopyable.hpp> 7 8 #include <boost/mpl/bool.hpp> 9 #include <boost/mpl/int.hpp> 10 #include <boost/mpl/for_each.hpp> 11 #include <boost/mpl/range_c.hpp> 12 #include <boost/mpl/vector.hpp> 13 #include <boost/mpl/transform.hpp> 14 #include <boost/mpl/erase.hpp> 15 16 #include <boost/fusion/include/vector.hpp> 17 #include <boost/fusion/include/for_each.hpp> 18 #include <boost/fusion/include/at_c.hpp> 19 #include <boost/fusion/mpl.hpp> 20 #include <boost/fusion/include/as_vector.hpp> 21 22 #include <memory> 23 24 /** 25 for loop generator which can use lambda expressions. 26 27 For example: 28 @code 29 using namespace generator; 30 using namespace boost::lambda; 31 make_for(N, N, range(bind(std::max<int>, _1, _2), N), range(_2, _3+1)); 32 // equivalent to pseudocode 33 // for l=0,N: for k=0,N: for j=max(l,k),N: for i=k,j 34 @endcode 35 36 If range is given as upper bound only, 37 lower bound is assumed to be default constructed 38 Lambda placeholders may only reference first three indices. 39 */ 40 41 namespace generator { 42 namespace detail { 43 44 using boost::lambda::constant_type; 45 using boost::lambda::constant; 46 47 /// lambda expression identity 48 template<class E, class enable = void> 49 struct lambda { 50 typedef E type; 51 }; 52 53 /// transform/construct constant lambda expression from non-lambda 54 template<class E> 55 struct lambda<E, typename boost::disable_if< 56 boost::lambda::is_lambda_functor<E> >::type> 57 { 58 struct constant : boost::lambda::constant_type<E>::type { 59 typedef typename boost::lambda::constant_type<E>::type base_type; 60 constant() : base_type(boost::lambda::constant(E())) {} 61 constant(const E &e) : base_type(boost::lambda::constant(e)) {} 62 }; 63 typedef constant type; 64 }; 65 66 /// range functor 67 template<class L, class U> 68 struct range_ { 69 typedef boost::array<int,4> index_type; 70 range_(U upper) : bounds_(typename lambda<L>::type(), upper) {} 71 range_(L lower, U upper) : bounds_(lower, upper) {} 72 73 template< typename T, size_t N> 74 T lower(const boost::array<T,N> &index) { 75 return bound<0>(index); 76 } 77 78 template< typename T, size_t N> 79 T upper(const boost::array<T,N> &index) { 80 return bound<1>(index); 81 } 82 83 private: 84 template<bool b, typename T> 85 T bound(const boost::array<T,1> &index) { 86 return (boost::fusion::at_c<b>(bounds_))(index[0]); 87 } 88 89 template<bool b, typename T> 90 T bound(const boost::array<T,2> &index) { 91 return (boost::fusion::at_c<b>(bounds_))(index[0], index[1]); 92 } 93 94 template<bool b, typename T, size_t N> 95 T bound(const boost::array<T,N> &index) { 96 using boost::fusion::at_c; 97 return (at_c<b>(bounds_))(index[0], index[1], index[2]); 98 } 99 100 boost::fusion::vector<typename lambda<L>::type, 101 typename lambda<U>::type> bounds_; 102 }; 103 104 template<typename T, size_t N> 105 struct for_base { 106 typedef boost::array<T,N> value_type; 107 virtual ~for_base() {} 108 virtual value_type next() = 0; 109 }; 110 111 /// N-index generator 112 template<typename T, size_t N, class R, class I> 113 struct for_ : for_base<T,N> { 114 typedef typename for_base<T,N>::value_type value_type; 115 typedef R range_tuple; 116 for_(const range_tuple &r) : r_(r), state_(true) { 117 boost::fusion::for_each(r_, initialize(index)); 118 } 119 /// @return new generator 120 for_* new_() { return new for_(r_); } 121 /// @return next index value and increment 122 value_type next() { 123 value_type next; 124 using namespace boost::lambda; 125 typename value_type::iterator n = next.begin(); 126 typename value_type::iterator i = index.begin(); 127 boost::mpl::for_each<I>(*(var(n))++ = var(i)[_1]); 128 129 state_ = advance<N>(r_, index); 130 return next; 131 } 132 /// @return false if out of bounds, true otherwise 133 operator bool() { return state_; } 134 135 private: 136 /// initialize indices 137 struct initialize { 138 value_type &index_; 139 mutable size_t i_; 140 initialize(value_type &index) : index_(index), i_(0) {} 141 template<class R_> void operator()(R_& r) const { 142 index_[i_++] = r.lower(index_); 143 } 144 }; 145 146 /// advance index[0:M) 147 template<size_t M> 148 struct advance { 149 /// stop recursion 150 struct stop { 151 stop(R r, value_type &index) {} 152 }; 153 /// advance index 154 /// @param r range tuple 155 /// @param index index array 156 advance(R &r, value_type &index) : index_(index), i_(0) { 157 namespace fusion = boost::fusion; 158 index[M-1] += 1; // increment index 159 fusion::for_each(r, *this); // update indices 160 state_ = index[M-1] >= fusion::at_c<M-1>(r).upper(index); 161 if (state_) { // out of bounds 162 typename boost::mpl::if_c<(M > 1), 163 advance<M-1>, stop>::type(r, index); 164 } 165 } 166 /// apply lower bound of range to index 167 template<typename R_> void operator()(R_& r) const { 168 if (i_ >= M) index_[i_] = r.lower(index_); 169 ++i_; 170 } 171 /// @return false if out of bounds, true otherwise 172 operator bool() { return state_; } 173 private: 174 value_type &index_; ///< index array reference 175 mutable size_t i_; ///< running index 176 bool state_; ///< out of bounds state 177 }; 178 179 value_type index; 180 range_tuple r_; 181 bool state_; 182 }; 183 184 185 /// polymorphic generator template base 186 template<typename T,size_t N> 187 struct For : boost::noncopyable { 188 typedef boost::array<T,N> value_type; 189 /// @return next index value and increment 190 value_type next() { return for_->next(); } 191 /// @return false if out of bounds, true otherwise 192 operator bool() const { return for_; } 193 protected: 194 /// reset smart pointer 195 void reset(for_base<T,N> *f) { for_.reset(f); } 196 std::auto_ptr<for_base<T,N> > for_; 197 }; 198 199 /// range [T,R) type 200 template<typename T, typename R> 201 struct range_type { 202 typedef range_<T,R> type; 203 }; 204 205 /// range identity specialization 206 template<typename T, class L, class U> 207 struct range_type<T, range_<L,U> > { 208 typedef range_<L,U> type; 209 }; 210 211 namespace fusion = boost::fusion; 212 namespace mpl = boost::mpl; 213 214 template<typename T, size_t N, class R1, class R2, class R3, class R4> 215 struct range_tuple { 216 // full range vector 217 typedef typename mpl::vector<R1,R2,R3,R4> v; 218 typedef typename mpl::end<v>::type end; 219 typedef typename mpl::advance_c<typename mpl::begin<v>::type, N>::type pos; 220 // [0:N) range vector 221 typedef typename mpl::erase<v, pos, end>::type t; 222 // transform into proper range fusion::vector 223 typedef typename fusion::result_of::as_vector< 224 typename mpl::transform<t,range_type<T, mpl::_1> >::type 225 >::type type; 226 }; 227 228 229 template<typename T, size_t N, 230 class R1, class R2, class R3, class R4, 231 class O> 232 struct for_type { 233 typedef typename range_tuple<T,N,R1,R2,R3,R4>::type range_tuple; 234 typedef for_<T, N, range_tuple, O> type; 235 }; 236 237 } // namespace detail 238 239 240 /// default index order, [0:N) 241 template<size_t N> 242 struct order { 243 typedef boost::mpl::range_c<size_t,0, N> type; 244 }; 245 246 /// N-loop generator, 0 < N <= 5 247 /// @tparam T index type 248 /// @tparam N number of indices/loops 249 /// @tparam R1,... range types 250 /// @tparam O index order 251 template<typename T, size_t N, 252 class R1, class R2 = void, class R3 = void, class R4 = void, 253 class O = typename order<N>::type> 254 struct for_ : detail::for_type<T, N, R1, R2, R3, R4, O>::type { 255 typedef typename detail::for_type<T, N, R1, R2, R3, R4, O>::type base_type; 256 typedef typename base_type::range_tuple range_tuple; 257 for_(const range_tuple &range) : base_type(range) {} 258 }; 259 260 /// loop range [L:U) 261 /// @tparam L lower bound type 262 /// @tparam U upper bound type 263 /// @return range 264 template<class L, class U> 265 detail::range_<L,U> range(L lower, U upper) { 266 return detail::range_<L,U>(lower, upper); 267 } 268 269 /// make 4-loop generator with specified index ordering 270 template<typename T, class R1, class R2, class R3, class R4, class O> 271 for_<T, 4, R1, R2, R3, R4, O> 272 make_for(R1 r1, R2 r2, R3 r3, R4 r4, const O&) { 273 typedef for_<T, 4, R1, R2, R3, R4, O> F; 274 return F(F::range_tuple(r1, r2, r3, r4)); 275 } 276 277 /// polymorphic generator template forward declaration 278 template<typename T,size_t N> 279 struct For; 280 281 /// polymorphic 4-loop generator 282 template<typename T> 283 struct For<T,4> : detail::For<T,4> { 284 /// generator with default index ordering 285 template<class R1, class R2, class R3, class R4> 286 For(R1 r1, R2 r2, R3 r3, R4 r4) { 287 this->reset(make_for<T>(r1, r2, r3, r4).new_()); 288 } 289 /// generator with specified index ordering 290 template<class R1, class R2, class R3, class R4, class O> 291 For(R1 r1, R2 r2, R3 r3, R4 r4, O o) { 292 this->reset(make_for<T>(r1, r2, r3, r4, o).new_()); 293 } 294 }; 295 296 } 297 298 299 #endif /* _GENERATOR_HPP_ */

    Read the article

< Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >