Search Results

Search found 36019 results on 1441 pages for 'access 2003'.

Page 73/1441 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• Network Access: I can't access 192.168.1.101 from 192.168.1.102.

  - by takpar

  Hi, I'm running Ubuntu 10.04 on my PC with IP 192.168.1.101. every thing work fine, e.g. my web server is running and I can see http://localhost/ or http://192.168.1.101 properly. But the problem is that I cannot see my PC from my laptop at 192.168.1.102 e.g. at my laptop http://192.168.1.101 gives Connection timed out in browser. or trying to telnet on any port leads to: telnet: Unable to connect to remote host: Connection timed out laptop is running a fresh install of Ubuntu as well and there is no setup for firewall stuff in both computers. PS: Both computers can ping each other well. The router is a cicso linksys wireless ADSL modem. Currently, I can connect to FTP server on the Windows running on 192.168.1.102 from 192.168.1.101 without problem. Theses are commands ran on my PC, 192.168.1.101: ifconfig: adp@adp-desktop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:e1:8e:cf inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::226:18ff:fee1:8ecf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1831935 errors:0 dropped:0 overruns:0 frame:0 TX packets:1493786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1996855925 (1.9 GB) TX bytes:215288238 (215.2 MB) Interrupt:27 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:951742 errors:0 dropped:0 overruns:0 frame:0 TX packets:951742 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:494351095 (494.3 MB) TX bytes:494351095 (494.3 MB) vmnet1 Link encap:Ethernet HWaddr 00:50:46:c0:00:01 inet addr:192.168.91.1 Bcast:192.168.91.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:50 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet HWaddr 00:50:46:c0:00:08 inet addr:192.168.156.1 Bcast:192.168.156.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) port 80 is set to 0.0.0.0 well: adp@adp-desktop:~$ netstat -ln | grep 'LISTEN ' tcp 0 0 127.0.0.1:52815 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4559 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4369 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:7634 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:21 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5269 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:25 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5280 0.0.0.0:* LISTEN tcp 0 0 127.0.1.1:7777 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:33601 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5222 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp6 0 0 :::139 :::* LISTEN tcp6 0 0 ::1:631 :::* LISTEN tcp6 0 0 :::445 :::* LISTEN /etc/hosts.deny is empty: adp@adp-desktop:~$ cat /etc/hosts.deny # /etc/hosts.deny: list of hosts that are _not_ allowed to access the system. # See the manual pages hosts_access(5) and hosts_options(5). # # Example: ALL: some.host.name, .some.domain # ALL EXCEPT in.fingerd: other.host.name, .other.domain # # If you're going to protect the portmapper use the name "portmap" for the # daemon name. Remember that you can only use the keyword "ALL" and IP # addresses (NOT host or domain names) for the portmapper, as well as for # rpc.mountd (the NFS mount daemon). See portmap(8) and rpc.mountd(8) # for further information. # # The PARANOID wildcard matches any host whose name does not match its # address. # # You may wish to enable this to ensure any programs that don't # validate looked up hostnames still leave understandable logs. In past # versions of Debian this has been the default. # ALL: PARANOID netstat -l: adp@adp-desktop:~$ netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 localhost:52815 *:* LISTEN tcp 0 0 *:hylafax *:* LISTEN tcp 0 0 *:www *:* LISTEN tcp 0 0 *:4369 *:* LISTEN tcp 0 0 localhost:7634 *:* LISTEN tcp 0 0 *:ftp *:* LISTEN tcp 0 0 *:xmpp-server *:* LISTEN tcp 0 0 localhost:ipp *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 *:5280 *:* LISTEN tcp 0 0 adp-desktop:7777 *:* LISTEN tcp 0 0 *:33601 *:* LISTEN tcp 0 0 *:xmpp-client *:* LISTEN tcp 0 0 localhost:mysql *:* LISTEN tcp6 0 0 [::]:netbios-ssn [::]:* LISTEN tcp6 0 0 localhost:ipp [::]:* LISTEN tcp6 0 0 [::]:microsoft-ds [::]:* LISTEN udp 0 0 *:bootpc *:* udp 0 0 *:mdns *:* udp 0 0 *:47467 *:* udp 0 0 192.168.1.10:netbios-ns *:* udp 0 0 192.168.91.1:netbios-ns *:* udp 0 0 192.168.156.:netbios-ns *:* udp 0 0 *:netbios-ns *:* udp 0 0 192.168.1.1:netbios-dgm *:* udp 0 0 192.168.91.:netbios-dgm *:* udp 0 0 192.168.156:netbios-dgm *:* udp 0 0 *:netbios-dgm *:* raw 0 0 *:icmp *:* 7 netstat -rn: adp@adp-desktop:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.91.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet1 192.168.156.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet8 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 commands on the laptop, 192.168.1.102: ifconfig: root@fakeuser-laptop:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:33:a2:31:15 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:21 eth1 Link encap:Ethernet HWaddr 00:2d:d9:3e:1f:6c inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::21d:d9ff:fe3e:1f6c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5681 errors:0 dropped:0 overruns:0 frame:10313 TX packets:6717 errors:6 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4055251 (4.0 MB) TX bytes:779308 (779.3 KB) Interrupt:18 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:206 errors:0 dropped:0 overruns:0 frame:0 TX packets:206 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15172 (15.1 KB) TX bytes:15172 (15.1 KB) netstat -rn: root@fakeuser-laptop:~# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1

  Read the article

• MySQL InnoDB Corruption after power outage, possible to recover?

  - by Tim Hackett

  Hey Guys, I recently started trying to get Redmine up and running after a power outage that seems to have corrupted our InnoDB database in MySQL. Redmine had an extensive set of documentation that I would like to get even if redmine isn't able to run. The service fails on startup. I have tried inserting innodb_force_recovery = 4 per the documentation from the url in the error log. (also tried 1 thru 6 as I have backed up all directories after the corruption) I have verified through "mysqld-nt --print-defaults" that it is starting with the recovery option in the params. The machine is running Windows Server 2003 SP2, Xeon E5335 with 2GB RAM, MySQL is not mirrored to another machine, nor is the machine a mirror. I do not have any backups because the previous person did not set them up. Here is the error log: InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 100308 14:50:01 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 100308 14:50:02 InnoDB: Error: page 7 log sequence number 0 935521175 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 2 log sequence number 0 935517607 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 11 log sequence number 0 935517607 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 5 log sequence number 0 972973045 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 6 log sequence number 0 972984051 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 1577 log sequence number 0 972737368 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. InnoDB: Error: trying to access page number 4294965119 in space 0, InnoDB: space name .\ibdata1, InnoDB: which is outside the tablespace bounds. InnoDB: Byte offset 0, len 16384, i/o type 10. InnoDB: If you get this error at mysqld startup, please check that InnoDB: your my.cnf matches the ibdata files that you have in the InnoDB: MySQL server. 100308 14:50:02InnoDB: Assertion failure in thread 960 in file .\fil\fil0fil.c line 3959 InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: about forcing recovery. 100308 14:50:02 [ERROR] mysqld-nt: Got signal 11. Aborting! 100308 14:50:02 [ERROR] Aborting 100308 14:50:02 [Note] mysqld-nt: Shutdown complete

  Read the article

• Access 2007: How can I make this EXPRESSION less complex?

  - by Mike

  Access is telling me that my new expression is to complex. It used to work when we had 10 service levels, but now we have 19! Great! My expression is checking the COST of our services in the [PriceCharged] field and then assigning the appropriate HOURS [Servicelevel] when I perform a calculation to work out how much REVENUE each colleague has made when working for a client. The [EstimatedTime] field stores the actual hours each colleague has worked. [EstimatedTime]/[ServiceLevel]*[PriceCharged] Great. Below is the breakdown of my COST to HOURS expression. I've put them on different lines to make it easier to read - please do not be put off by the length of this post, it's all the same info in the end. Many thanks,Mike ServiceLevel: IIf([pricecharged]=100(COST),6(HOURS), IIf([pricecharged]=200 Or [pricecharged]=210,12.5, IIf([pricecharged]=300,19, IIf([pricecharged]=400 Or [pricecharged]=410,25, IIf([pricecharged]=500,31, IIf([pricecharged]=600,37.5, IIf([pricecharged]=700,43, IIf([pricecharged]=800 Or [pricecharged]=810,50, IIf([pricecharged]=900,56, IIf([pricecharged]=1000,62.5, IIf([pricecharged]=1100,69, IIf([pricecharged]=1200 Or [pricecharged]=1210,75, IIf([pricecharged]=1300 Or [pricecharged]=1310,100, IIf([pricecharged]=1400,125, IIf([pricecharged]=1500,150, IIf([pricecharged]=1600,175, IIf([pricecharged]=1700,200, IIf([pricecharged]=1800,225, IIf([pricecharged]=1900,250,0)))))))))))))))))))

  Read the article

• Access 2007: How can I make this EXPRESSION less complex?

  - by Mike

  Access is telling me that my new expression is to complex. It used to work when we had 10 service levels, but now we have 19! Great! My expression is checking the COST of our services in the [PriceCharged] field and then assigning the appropriate HOURS [Servicelevel] when I perform a calculation to work out how much REVENUE each colleague has made when working for a client. The [EstimatedTime] field stores the actual hours each colleague has worked. [EstimatedTime]/[ServiceLevel]*[PriceCharged] Great. Below is the breakdown of my COST to HOURS expression. I've put them on different lines to make it easier to read - please do not be put off by the length of this post, it's all the same info in the end. Many thanks,Mike ServiceLevel: IIf([pricecharged]=100(COST),6(HOURS), IIf([pricecharged]=200 Or [pricecharged]=210,12.5, IIf([pricecharged]=300,19, IIf([pricecharged]=400 Or [pricecharged]=410,25, IIf([pricecharged]=500,31, IIf([pricecharged]=600,37.5, IIf([pricecharged]=700,43, IIf([pricecharged]=800 Or [pricecharged]=810,50, IIf([pricecharged]=900,56, IIf([pricecharged]=1000,62.5, IIf([pricecharged]=1100,69, IIf([pricecharged]=1200 Or [pricecharged]=1210,75, IIf([pricecharged]=1300 Or [pricecharged]=1310,100, IIf([pricecharged]=1400,125, IIf([pricecharged]=1500,150, IIf([pricecharged]=1600,175, IIf([pricecharged]=1700,200, IIf([pricecharged]=1800,225, IIf([pricecharged]=1900,250,0)))))))))))))))))))

  Read the article

• Active Directory: trouble adding new DC

  - by ethrbunny

  I have a domain with 3 DCs. One is starting to fail so I brought up a new one. All are running Win 2003. Problem: there appear to be replication issues between the 4 machines but I can't figure out what's causing this. All are registered with the DNS as identically as I can make them. How do I know there is a problem? Nagios is telling me that the other 3 DCs are having KCCEvent errors and the new machine is reporting "failed connectivity" errors. Doing dcdiag on the new machine reports: the host could not be resolved to an IP address. This seems crazy as I log into it using the DNS name. I can ping it from the other three machines using this DNS name as well. repadmin /showreps from the new machine says its seeing the other 3 machines. Doing the same from one of the older machines doesn't show the new machine. I've tried netdiag /repair numerous times. No luck. There are no firewalls running on any of the machines. If I look at Domain info via MMC (on the new machine) it appears that all the information is current. Users, computers, DCs.. its all there. Im puzzled as to what step(s) I've missed in adding this new machine. Suggestions? EDIT: dcdiag from non-working: C:\Documents and Settings\Administrator.BME>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\YELLOW Starting test: Connectivity The host 312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu could not be resolved to an IP address. Check the DNS server, DHCP, server name, etc Although the Guid DNS name (312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu) couldn't be resolved, the server name (yellow.server.edu) resolved to the IP address (10.127.24.79) and was pingable. Check that the IP address is registered correctly with the DNS server. ......................... YELLOW failed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\YELLOW Skipping all tests, because server YELLOW is not responding to directory service requests Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck dcdiag from working: P:\>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\AD1 Starting test: Connectivity ......................... AD1 passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\AD1 Starting test: Replications ......................... AD1 passed test Replications Starting test: NCSecDesc ......................... AD1 passed test NCSecDesc Starting test: NetLogons ......................... AD1 passed test NetLogons Starting test: Advertising ......................... AD1 passed test Advertising Starting test: KnowsOfRoleHolders ......................... AD1 passed test KnowsOfRoleHolders Starting test: RidManager ......................... AD1 passed test RidManager Starting test: MachineAccount ......................... AD1 passed test MachineAccount Starting test: Services ......................... AD1 passed test Services Starting test: ObjectsReplicated ......................... AD1 passed test ObjectsReplicated Starting test: frssysvol ......................... AD1 passed test frssysvol Starting test: frsevent ......................... AD1 passed test frsevent Starting test: kccevent ......................... AD1 passed test kccevent Starting test: systemlog ......................... AD1 passed test systemlog Starting test: VerifyReferences ......................... AD1 passed test VerifyReferences Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck P:\>

  Read the article

• Hide subdomain AND subdirectory using mod_rewrite?

  - by Jeremy

  I am trying to hide a subdomain and subdirectory from users. I know it may be easier to use a virtual host but will that not change direct links pointing at our site? The site currently resides at http://mail.ctrc.sk.ca/cms/ I want www.ctrc.sk.ca and ctrc.sk.ca to access this folder but still display www.ctrc.sk.ca. If that makes any sense. Here is what our current .htaccess file looks like, we are using Joomla so there already a few rules set up. Help is appreciated. # Helicon ISAPI_Rewrite configuration file # Version 3.1.0.78 ## # @version $Id: htaccess.txt 14401 2010-01-26 14:10:00Z louis $ # @package Joomla # @copyright Copyright (C) 2005 - 2010 Open Source Matters. All rights reserved. # @license http://www.gnu.org/copyleft/gpl.html GNU/GPL # Joomla! is Free Software ## ##################################################### # READ THIS COMPLETELY IF YOU CHOOSE TO USE THIS FILE # # The line just below this section: 'Options +FollowSymLinks' may cause problems # with some server configurations. It is required for use of mod_rewrite, but may already # be set by your server administrator in a way that dissallows changing it in # your .htaccess file. If using it causes your server to error out, comment it out (add # to # beginning of line), reload your site in your browser and test your sef url's. If they work, # it has been set by your server administrator and you do not need it set here. # ##################################################### ## Can be commented out if causes errors, see notes above. #Options +FollowSymLinks # # mod_rewrite in use RewriteEngine On ########## Begin - Rewrite rules to block out some common exploits ## If you experience problems on your site block out the operations listed below ## This attempts to block the most common type of exploit `attempts` to Joomla! # ## Deny access to extension xml files (uncomment out to activate) #<Files ~ "\.xml$"> #Order allow,deny #Deny from all #Satisfy all #</Files> ## End of deny access to extension xml files RewriteCond %{QUERY_STRING} mosConfig_[a-zA-Z_]{1,21}(=|\%3D) [OR] # Block out any script trying to base64_encode crap to send via URL RewriteCond %{QUERY_STRING} base64_encode.*\(.*\) [OR] # Block out any script that includes a <script> tag in URL RewriteCond %{QUERY_STRING} (\<|%3C).*script.*(\>|%3E) [NC,OR] # Block out any script trying to set a PHP GLOBALS variable via URL RewriteCond %{QUERY_STRING} GLOBALS(=|\[|\%[0-9A-Z]{0,2}) [OR] # Block out any script trying to modify a _REQUEST variable via URL RewriteCond %{QUERY_STRING} _REQUEST(=|\[|\%[0-9A-Z]{0,2}) # Send all blocked request to homepage with 403 Forbidden error! RewriteRule ^(.*)$ index.php [F,L] # ########## End - Rewrite rules to block out some common exploits # Uncomment following line if your webserver's URL # is not directly related to physical file paths. # Update Your Joomla! Directory (just / for root) #RewriteBase / ########## Begin - Joomla! core SEF Section # RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/index.php RewriteCond %{REQUEST_URI} (/|\.php|\.html|\.htm|\.feed|\.pdf|\.raw|/[^.]*)$ [NC] RewriteRule (.*) index.php RewriteRule .* - [E=HTTP_AUTHORIZATION:%{HTTP:Authorization},L] # ########## End - Joomla! core SEF Section EDIT Yes, mail.ctrc.sk.ca/cms/ is the root directory. Currently the DNS redirects from ctrc.sk.ca and www.ctrc.sk.ca to mail.ctrc.sk.ca/cms. However when it redirects the user still sees the mail.ctrc.sk.ca/cms/ url and I want them to only see www.ctrc.sk.ca.

  Read the article

• ASA access lists and Egress Filtering

  - by Nate

  Hello. I'm trying to learn how to use a cisco ASA firewall, and I don't really know what I'm doing. I'm trying to set up some egress filtering, with the goal of allowing only the minimal amount of traffic out of the network, even if it originated from within the inside interface. In other words, I'm trying to set up dmz_in and inside_in ACLs as if the inside interface is not too trustworthy. I haven't fully grasped all the concepts yet, so I have a few issues. Assume that we're working with three interfaces: inside, outside, and DMZ. Let's say I have a server (X.Y.Z.1) that has to respond to PING, HTTP, SSH, FTP, MySQL, and SMTP. My ACL looks something like this: access-list outside_in extended permit icmp any host X.Y.Z.1 echo-reply access-list outside_in extended permit tcp any host X.Y.Z.1 eq www access-list outside_in extended permit tcp any host X.Y.Z.1 eq ssh access-list outside_in extended permit tcp any host X.Y.Z.1 eq ftp access-list outside_in extended permit tcp any host X.Y.Z.1 eq ftp-data established access-list outside_in extended permit tcp any host X.Y.Z.1 eq 3306 access-list outside_in extended permit tcp any host X.Y.Z.1 eq smtp and I apply it like this: access-group outside_in in interface outside My question is, what can I do for egress filtering? I want to only allow the minimal amount of traffic out. Do I just "reverse" the rules (i.e. the smtp rule becomes access-list inside_out extended permit tcp host X.Y.Z.1 any eq smtp ) and call it a day, or can I further cull my options? What can I safely block? Furthermore, when doing egress filtering, is it enough to apply "inverted" rules to the outside interface, or should I also look into making dmz_in and inside_in acls? I've heard the term "egress filtering" thrown around a lot, but I don't really know what I'm doing. Any pointers towards good resources and reading would also be helpful, most of the ones I've found presume that I know a lot more than I do.

  Read the article

• Outlook 2003 add-in - Getting COM exception on application shutdown after creating WPF window

  - by Oliver Hanappi

  Hi! I'm developing an outlook 2003 add-in. Until now I used only winforms to display one form, but today I've added a WPF window for more complex stuff. DUe to the WPF window, a COM exception is being thrown when outlook shuts down. Does anybody know why? I need to start a separate thread for the WPF window in single apartment state. Here is the exception: System.Runtime.InteropServices.InvalidComObjectException was unhandled Message="COM object that has been separated from its underlying RCW cannot be used." Source="PresentationCore" StackTrace: at System.Windows.Input.TextServicesContext.StopTransitoryExtension() at System.Windows.Input.TextServicesContext.Uninitialize(Boolean appDomainShutdown) at System.Windows.Input.TextServicesContext.TextServicesContextShutDownListener.OnShutDown(Object target) at MS.Internal.ShutDownListener.HandleShutDown(Object sender, EventArgs e) InnerException: Best Regards, Oliver Hanappi

  Read the article

• OutOfMemoryException with Image.Clone - Only on Windows 2003

  - by Jeff Rapp

  So here's my issue. I have an image that I need to shrink. The original image is a grayscale PNG, which isn't a huge issues except that when I shrink it down, the thermal label printers pickup the artifacts and print them on the label. So, what I did was change the image to black & white (Format1bppIndexed) before resizing, like this: Dim bte() As Byte = System.Convert.FromBase64String(imgStr) Dim ms As New IO.MemoryStream(bte) Dim bmp As New System.Drawing.Bitmap(ms) Dim monoImage As Drawing.Bitmap = New Drawing.Bitmap(1200, 1800, Drawing.Imaging.PixelFormat.Format1bppIndexed) Dim rect As New Drawing.Rectangle(0, 0, 1200, 1800) monoImage = bmp.Clone(rect, Drawing.Imaging.PixelFormat.Format1bppIndexed) And then I resize it. This code works fine on my Windows 7 machine, but when I run it on the Windows 2003 Server box that it calls home, it always throws an OutOfMemoryException when it hits the bmp.Clone line. Any ideas as to what's happening, or perhaps a better solution to converting the image to B&W?

  Read the article

• WMI Windows 7 vs Server 2003 R2 Problem

  - by Shahmir Javaid

  I have the below procedures running one after the Other. It seems to work fine in Windows 7 but fails on Windows Server 2003 R2. Any Ideas Why? Am i suppose to be disposing For Cpu ManagementObjectSearcher cpuSearcher = new ManagementObjectSearcher("root\\CIMv2", "SELECT * FROM Win32_Processor"); foreach (ManagementObject cpuObj in cpuSearcher.Get()) { cpu.Add(new cpuinfo(cpuObj["Name"].ToString())); cpuObj.Dispose(); } cpuSearcher.Dispose(); For Memory ManagementObjectSearcher memSearcher = new ManagementObjectSearcher("root\\CIMv2", "SELECT Capacity FROM Win32_PhysicalMemory"); //Get total Memory foreach (ManagementObject memObj in memSearcher.Get()) { MemTotal += (Int64.Parse((memObj["Capacity"].ToString()))); memObj.Dispose(); } Any Help would be apreaciated

  Read the article

• Visual Studio .NET 2003 - Ignore Specific Library for libcmt vs libcmtd

  - by tefd

  Hi, I have a template VS .NET 2003 project, which colleagues copy and customise when developing their software. It appears the template was altered a while back to set the IgnoreSpecificLibrary property to have libcmt.lib for both release and debug builds (i.e. for both release and debug, the build should ignore libcmt.lib in the linker). Some projects based on this have since been built, with the release build pulling in libcmtd.lib (evident by looking through the project .map file) which appears to have caused some runtime issues (i.e. a dialog window being flashed up as though a breakpoint had been set). Does setting IgnoreSpecificLibrary to exclude libcmt.lib automatically make the project link against libcmtd.lib? What is weird is that building the template (with the incorrect setting) links against libcmt.lib whereas some of the customised projects (though not all) link against libcmtd.lib. Any ideas?

  Read the article

• Disassemble Microsoft Visual Studio 2003 compiler output

  - by Carl Norum

  I'm seeing what I think is strange behaviour from object files output by the Microsoft Visual Studio 2003 tools. The file utility tells me: asmfile.obj: 80386 COFF executable not stripped - version 30821 For objects created by the assembler, but for objects coming from C files, I get just: cfile.obj: data Using Microsoft's dumpbin utility and the objdump I got from cygwin, I can disassemble the assembly-built file, but I get no useful results from either utility for the C-built files. I have a couple of questions related to this difference: What is the object file format generated by the MSVC2003 compiler? How can I disassemble that object file? I am particularly interested in getting the disassembly in AT&T syntax - I'm doing a port of a large source base to make it work with GCC, and I would like to use this method as a shortcut for some of the inline assembly routines in the project. Thanks!

  Read the article

• Connect to a running instance of Visual Studio 2003 using COM, build and read output

  - by codeape

  For Visual Studio 6.0, I can connect to a running instance like: o = GetActiveObject("MSDev.Application") What prog ID do I use for Visual Studio 2003? How do I execute a 'Build Solution' once I have the COM object that references the VS2003 instance? How do I get the string contents of the build output window after executing the build solution command? Yes, I am aware that I can build a solution from the command line. But in this case, I need to connect to a running instance of Visual Studio. EDIT: found and submitted an answer, see below.

  Read the article

• Outlook 2003 Add-In Setup Project with COM DLL Deployment Problem

  - by Malkier

  Hi, I developed an Outlook 2003 add-in which uses the com dll redemption. I created a visual studio 2008 setup project, added a custom action to run "caspol.exe -machine -addgroup 1 -strong -hex [key] -noname -noversion FullTrust -n \"Name\" -description \"desc\" and moved the registry keys under software to HKLM as described in http://msdn.microsoft.com/en-us/library/cc136646.aspx#AutoDeployVSTOse_InstallingtheAddinforAllUsers to ensure all-users compatibility. I included the redemption.dll in the setup with vsdrfCOMSelfReg (vsdrfCOM throwed an error). My problem is: When installing the setup on a test machine under an admin account, it runs fine under all users, however when we use the company wide software deployment which runs under a system account the setup executes but the add-in wont load. If I repair the installation with an admin account again it loads just fine. Shouldn't a system account have the required permissions to install all of the components? What options do I have? Thanks for any suggestions.

  Read the article

• Access ADP - For/Against?

  - by webworm

  I have been tasked with taking an Access 97 application and moving the back-end data to SQL Server while moving the front end to Access 2003 (using Access Data Projects). In the process of this migration the back-end data structures will be changed significantly to support new functionality. If I had my wish we would not be using Access as the front end. I think our application would be much better served by WinForms, WPF, or a web application. We have the time needed to properly plan a business logic layer and implement an excellent solution but powers above me want to stay with Access because that is what they are familiar with. What I could use help with is pros/cons of continuing down this path of Access development. What are some legitimate arguments for and against using Access 2003? Here is what I have come up with so far. Pro Access: Already own Access 2003 licenses Easy GUI development Reports look nice Against Access Having to use VBA (Visual Basic for Applications) ADO vs DAO. Didn't Microsoft change things from Access 2002 to Access 2003? Not tied to Access runtime Choice in front end (WPF, WinForms, even ASP.NET) Maintainability True separation of logic from UI not possible Does Microsoft still support Access ADP? Perhaps there are other issues I am not aware off both for and against Access for application development. I am trying to keep an open mind while at the same time trying to maintain my sanity. I have been using C# since .NET was released and the thought of going back to VBA for six months makes my head hurt. Especially when I feel I could offer so much more if allowed to develop with modern languages and tools?

  Read the article

• I want to add a Quality Assurance domain. How do I handle DNS servers?

  - by Tim

  I'm advising a large client on how to isolate their dev and testing from their production. They already have one domain, lets say xyz.net with the active directory domain as "XYZ01". I want to add second domain say QAxyz.net and make its active directory domain "QA01" All development and QA servers would be moved to the QAxyz.net domain, the machines would be part of the QA01 domain. Note: Some of these servers will have the same name as the production servers for testing purposes. I believe we would have separate DNS servers for each domain. If I am logged into the QA01 domain, to access the production domain I would qualify my access like so: \PRODSERVER.xyz.net login: XYZ01\username Do I need to add a forwarder to my QAxyz.net DNS server so that it can see xyz.net? Would I need to do the same to the xyz.net DNS server to see QAxyz.net? I don't know how to advise them in this. Does anyone have any other recommendations to isolationg a QA domain? Many Thanks in advance! Tim

  Read the article

• Macro VBA to get selected text in Outlook 2003

  - by balalakshmi

  I am trying to use this code snippet to get the selected text in outlook 2003 Sub SelectedTextDispaly() On Error Resume Next Err.Clear Dim oText As TextRange ''# Get an object reference to the selected text range. Set oText = ActiveWindow.Selection.TextRange ''# Check to see whether error occurred when getting text object ''# reference. If Err.Number <> 0 Then MsgBox "Invalid Selection. Please highlight some text " _ & "or select a text frame and run the macro again.", _ vbExclamation End End If ''# Display the selected text in a message box. If oText.Text = "" Then MsgBox "No Text Selected.", vbInformation Else MsgBox oText.Text, vbInformation End If End Sub When running this macro I get the error --------------------------- Microsoft Visual Basic --------------------------- Compile error: User-defined type not defined Do I need to add any references to fix this up?

  Read the article

• Generate xml containing animation information from ms ppt 2003/07 file

  - by Ravisha

  I am planning to write an application which has UI from MS ppt.Here is where all the animation will be configured. My application will just read xmls containing animation configuration and run it on a target device(Cannot mention details w.r.t device right now ,apologies for that) Not necessary that i want xmls it self but if there is a way to get animation details directly from the ppt file i will be more than happy. I will be going ahead with C#.Net 3.0 with windows XP as my OS.MY office will be either 2003 or 07.Can switch to any of these versions Please give suggestions as what will be the starting point for the same.Thanks in advance Please Let me know if any more details are needed

  Read the article

• How to inactive Active Directory users, 1 month after their FIRST LOGIN, instead of defining a solid expiration date

  - by smhnaji

  We want to give access to some Active Directory users, so they can remotely have access to our server and download from a special folder of the server. The licenses we give to users, are time base. There should be 1 month, 2 month, ..., 1 year, ... licenses. CURRENT SITUATION (WHAT I DON'T WANT): When users are created and added to the OS, a solid expiration date is given. WHAT I WANT: Users' expiration date should be calculated automatically after the first login. The user might not need his account right when purchases the license. In other words: When a license of the user we create is purchased at Jan 1st, he should use the license until Feb 1st. No matter whether he really logs in or not. He cannot come Feb 5th and begin using his license because that has expired then. What I want is that when he comes at Feb 5th and begins using, the license update until March 5th. Working environment is Windows Server 2012. By the word 'user', I mean Active Directory Users.

  Read the article

• excel 2003 can`t edit comments (user)

  - by Dezigo

  I have a .xls file of excel 2003. There are a lot of comments. I can`t edit it. right click -edit comments for example: I have comment: Ludmila: comment goes here Then Ludmila: comment goes here Dezigo:new comment..! I tryed to do: Tools-options-general (change my name to Ludmila),but it`s not work.. Like it Ludmila: comment goes here Ludmila:new comment.. and comment goes here -can`t edit it. file is not protected.

  Read the article

• An explanation of memory usage on Windows server 2003

  - by Rich

  Hi, We've been working on a bit of puzzle at work. We have an application service installed on two machines, both running Windows server 2003. These services do exactly the same thing. However once loaded, one of the services uses 200mb less than the other service. We're at a bit of a loss to what might be causing this discrepancy. I was wondering if there was some kind of server setting that would cause an application to use more memory (heap block size) or anything to explain this. If anyone has any ideas on what may be causing this, or how to find out what is causing this I'd be very grateful. Cheers Rich

  Read the article

• Can ping IP address and nslookup hostname but cannot ping hostname

  - by jao

  On a windows 2003 server I can nslookup www.google.com which returns Server: localhost Address: 127.0.0.1 Non-authoritative answer: Name: www.l.google.com Addresses: 74.125.79.104, 74.125.79.147, 74.125.79.99 Aliases: www.google.com I can then ping 74.125.79.104: Pinging 74.125.79.104 with 32 bytes of data: Reply from 74.125.79.104: bytes=32 time=16ms TTL=54 Reply from 74.125.79.104: bytes=32 time=32ms TTL=54 Reply from 74.125.79.104: bytes=32 time=15ms TTL=54 Reply from 74.125.79.104: bytes=32 time=15ms TTL=54 Ping statistics for 74.125.79.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 15ms, Maximum = 32ms, Average = 19ms But I cannot ping www.google.com: Ping request could not find host www.google.com. Please check the name and try again. (this one is different from the other question in that this one has a TLD, it is not a local domain.) Update: I am running a dns server at localhost (127.0.0.1). Even when I change it to use for example opendns, it still can nslookup hostname and ping ip address, but not ping hostname. So what is wrong? Update 2: here is the ipconfig /all result: Windows IP Configuration Host Name . . . . . . . . . . . . : SERVER Primary Dns Suffix . . . . . . . : NETWORK.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : NETWORK.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-0F-1F-56-3B-AA DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.7.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.7.1 DNS Servers . . . . . . . . . . . : 127.0.0.1 Update 3: Thanks everyone for their help and suggestions. I appreciate that. Ipconfig /flushdns returns: Sucessfully flushed the DNS resolver cache Ipconfig /displaydns returns: 2.7.168.192.in-addr.arpa ---------------------------------------- Record Name . . . . . : 2.7.168.192.in-addr.arpa. Record Type . . . . . : 12 Time To Live . . . . : 0 Data Length . . . . . : 4 Section . . . . . . . : Answer PTR Record . . . . . : webserver.mydomainname.com 1.0.0.127.in-addr.arpa ---------------------------------------- Record Name . . . . . : 1.0.0.127.in-addr.arpa. Record Type . . . . . : 12 Time To Live . . . . : 0 Data Length . . . . . : 4 Section . . . . . . . : Answer PTR Record . . . . . : localhost Update 4: Wireshark shows the following: 3 11.540542 208.67.220.220 192.168.7.2 DNS Standard query response A 74.125.79.99 A 74.125.79.104 A 74.125.79.147 6 42.056794 192.168.7.2 192.168.7.255 NBNS Name query NB WWW.GOOGLE.COM<00> which is weird: when I ping, it sends a packet to 192.168.7.255 instead of asking the DNS server for an address

  Read the article

• NX/SSH remote access with Remmina

  - by Niklas

  After many days and a lot of frustration, I managed to get freenx to work on my home server. I can connect to it with nomachine's linux client, but I want to use Remmina for this purpose. The problem is that I don't exactly know how to connect to a NX-server with the program. In the connection dialog, I've chosen SSH as the protocol, and I've correctly added the IP and port. Under "SSH Authentication" I've added my user name on the server, and I choose "identity file" and selected the ssh-key I generated (which works with nxclient). (When am I supposed to provide my password for the user on the server?) When I try to connect I get the message: SSH public key authentication failed: Public key file doesn't exist Why do I get this message? How shall I proceed correctly to get the authentication working? Thank you for your time!

  Read the article

• How To Access Your eBook Collection Anywhere in the World

  - by Jason Fitzpatrick

  If you have an eBook reader it’s likely you already have a collection of eBooks you sync to your reader from your home computer. What if you’re away from home or not sitting at your computer? Learn how to download books from your personal collection anywhere in the world (or just from your backyard). You have an eBook reader, you have an eBook collection, and when you remember to sync your books to the collection on your computer everything is rosy. What about when you forget or when the syncing process for your device is a bit of a hassle? (We’re looking at you, iPad.) Today we’re going to show you how to download eBooks to your eBook reader from anywhere in the world using a cross-platform solution Latest Features How-To Geek ETC How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Is Your Desktop Printer More Expensive Than Printing Services? 20 OS X Keyboard Shortcuts You Might Not Know HTG Explains: Which Linux File System Should You Choose? HTG Explains: Why Does Photo Paper Improve Print Quality? Sunrise on the Alien Desert Planet Wallpaper Add Falling Snow to Webpages with the Snowfall Extension for Opera [Browser Fun] Automatically Keep Up With the Latest Releases from Mozilla Labs in Firefox 4.0 A Look Back at 2010 Through Infographics Monitor the Weather with the Weather Forecast Extension for Opera Orbiting at the Edge of the Atmosphere Wallpaper

  Read the article

• Access Services in SharePoint Server 2010

  - by Wayne

  Another SharePoint Server 2010 feature which cannot go unnoticed is the Access Services. Access Services is a service in SharePoint Server 2010 that allows administrators to view, edit, and configure a Microsoft access application within a Web Browser. Access Services settings support backup and recovery, regardless of whether there is a UI setting in Central Administration. However, backup and recovery only apply to service-level and administrative-level settings; end-user content from the Access application is not backed up as part of this process. Access Services has Windows PowerShell functionality that can be used to provide the service that uses settings from a previous backup; configure and manage macro and query setting; manage and configure session management; and configure all the global settings of the service. Key Benefits of SharePoint Server Access Services Easier Access to right tools: The enhanced, customizable Ribbon in Access 2010 makes it easy to uncover more commands so you can focus on the end product. The new Microsoft Office BackstageTM view is yet another feature that can help you easily analyze and document your database, share, publish, and customize your Access 2010 experience, all from one convenient location. Helps build database effortlessly and quickly: Out-of-the box templates and reusable components make Access Services the fastest, simplest database solution available. It helps find new pre-built templates which you can start using without customization or select templates created by your peers in the Access online community and customize them to meet your needs. It builds your databases with new modular components. New Application Parts enable you to add a set of common Access components, such as a table and form for task management, to your database in a few simple clicks. Database navigation is now simplified. It creates Navigation Forms and makes your frequently used forms and reports more accessible without writing any code or logic. Create Impactful forms and reports: Whether it's an inventory of your assets or customer sales database, Access 2010 brings the innovative tools you'd expect from Microsoft Office. Access Services easily spot trends and add emphasis to your data. It quickly create coordinating database forms and reports and bring the Web into your database. Obtain a centralized landing pad for your data: Access 2010 offers easy ways to bring your data together and help increase work quality. New technologies help break down barriers so you can share and work together on your databases, making you or your team more efficient and productive. Add automation and complex expressions: If you need a more robust database design, such as preventing record deletion if a specific condition is met or if you need to create calculations to forecast your budget, Access 2010 empowers you to be your own developer. The enhanced Expression Builder greatly simplifies your expression building experience with IntelliSense®. With the revamped Macro Designer, it's now even easier for you to add basic logic to your database. New Data Macros allow you to attach logic to your data, centralizing the logic on the table, not the objects that update your data. Key features of Access Services 2010 - Access database content through a Web browser: Newly added Access Services on Microsoft SharePoint Server 2010 enables you to make your databases available on the Web with new Web databases. Users without an Access client can open Web forms and reports via a browser and changes are automatically synchronized. - Simplify how you access the features you need: The Ribbon, improved in Access 2010, helps you access commands even more quickly by enabling you to customize or create your own tabs. The new Microsoft Office Backstage view replaces the traditional File menu to provide one central, organized location for all of your document management tasks. - Codeless navigation: Use professional looking web-like navigation forms to make frequently used forms and reports more accessible without writing any code or logic. - Easily reuse Access items in other databases: Use Application Parts to add pre-built Access components for common tasks to your database in a few simple clicks. You can also package common database components, such as data entry forms and reports for task management, and reuse them across your organization or other databases. - Simplified formatting: By using Office themes you can create coordinating professional forms and reports across your database. Simply select a familiar and great looking Office theme, or design your own, and apply it to your database. Newly created Access objects will automatically match your chosen theme.

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >