Search Results

Search found 14598 results on 584 pages for 'address'.

Page 73/584 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• Cisco: unable to negotiate IP using IPCP with Windows server

  - by lnk

  I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

  Read the article

• ifconfig not showing all IPs bound to the machine

  - by pankaj sharma

  I have configured multiple IP addresses on a ubuntu box, but when I run ifconfig it shows just one of them. I am able, however, to ping all other adresses assigned to this machine. /etc/network/interface contents: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.202.11 netmask 255.255.255.0 network 192.168.202.0 broadcast 192.168.202.255 gateway 192.168.202.1 # dns-* options are implemented by the resolvconf package, if installed dns-search idil.dz1.da auto eth0:1 iface eth0:1 inet static address 192.168.202.12 netmask 255.255.255.0 auto eth0:2 iface eth0:2 inet static address 192.168.202.13 netmask 255.255.255.0 auto eth0:3 iface eth0:3 inet static address 192.168.202.14 netmask 255.255.255.0 auto eth0:4 iface eth0:4 inet static address 192.168.202.15 netmask 255.255.255.0 auto eth0:5 iface eth0:5 inet static address 192.168.202.16 netmask 255.255.255.0 but the output of the ifconfig is only: 192.168.202.11

  Read the article

• external disk dont work on ubuntu

  - by Skirki

  i have problem with in my ubuntu: when i connect external imation apollo disc i dont see a file system. Disk is working because in windows OS on this same computer it works as well. when i typed dmesg i got following logs [12913.260078] usb 4-1: new low speed USB device using ohci_hcd and address 15 [12913.440072] usb 4-1: device descriptor read/64, error -62 [12913.730058] usb 4-1: device descriptor read/64, error -62 [12914.020085] usb 4-1: new low speed USB device using ohci_hcd and address 16 [12914.200082] usb 4-1: device descriptor read/64, error -62 [12914.490150] usb 4-1: device descriptor read/64, error -62 [12914.780064] usb 4-1: new low speed USB device using ohci_hcd and address 17 [12915.200070] usb 4-1: device not accepting address 17, error -62 [12915.380081] usb 4-1: new low speed USB device using ohci_hcd and address 18 [12915.800065] usb 4-1: device not accepting address 18, error -62 [12915.800100] hub 4-0:1.0: unable to enumerate USB device on port 1 i trying to fix that by use commands: cd /sys/bus/pci/drivers/ehci_hcd echo -n "0000:00:02.1" unbind but it did not match the result and i don't have any other idea

  Read the article

• External 1TB WD USB 3.0 HDD is not detecting. Working perfectly find in Windows

  - by Yathi

  My 1TB USB 3.0 was working fine earlier in Ubuntu as well as Windows. But lately it is not at all being detected in Ubuntu. It still works fine in Windows. I did update my Ubuntu to 12.10 but I am not sure if that caused the issue. When I connect my HDD and run dmesg | tail: [ 47.804676] usb 4-3: >Device not responding to set address. [ 48.008575] usb 4-3: >Device not responding to set address. [ 48.212421] usb 4-3: >device not accepting address 9, error -71 [ 48.324451] usb 4-3: >Device not responding to set address. [ 48.528340] usb 4-3: >Device not responding to set address. [ 48.732165] usb 4-3: >device not accepting address 10, error -71 [ 48.844138] usb 4-3: >Device not responding to set address. [ 49.048179] usb 4-3: >Device not responding to set address. [ 49.251881] usb 4-3: >device not accepting address 11, error -71 [ 49.251907] hub 4-0:1.0: >unable to enumerate USB device on port 3 The output of sudo fdisk -l is : Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030cde Device Boot Start End Blocks Id System /dev/sda1 2048 1332981759 666489856 83 Linux /dev/sda2 1332981760 1953523711 310270976 5 Extended /dev/sda5 1332983808 1349365759 8190976 82 Linux swap / Solaris /dev/sda6 1349367808 1953523711 302077952 7 HPFS/NTFS/exFAT Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a2519 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 103368703 51683328 7 HPFS/NTFS/exFAT /dev/sdb2 103368704 154568703 25600000 83 Linux /dev/sdb3 154568704 234440703 39936000 7 HPFS/NTFS/exFAT /dev/sda and /dev/sdb are my 2 internal HDDs. But the external one which should be /dev/sdc is not even being shown though it is connected and the LED on the HDD is glowing. Someone had suggested adding blacklist uas to /etc/modprobe.d/blacklist.conf. Tried that as well. But still not working. Can someone help me out.

  Read the article

• Domino HTTP Server: Error - Unable to Bind 1.2.3.4, port 80, port in use or Bind To Host configuration specifies a duplicate IP address/host

  - by pdewaard

  We have a Domino 9.0.1 Server hosted on Ubuntu 14.04 Server, which hosts several other http based Tasks, (Nginx, Couchdb, Confluence on Tomcat). The Ubuntu Server has multiple IPs, all bind correctly to the different Tasks. The Domino SMTP task binds correctly and is working well. All http tasks (other than Domino) are proxied behind Nginx version 1.6x and all are working well, netstat shows no 0.0.0.0 bindings, no one is listening on 1.2.3.4:80 . when I try to load http on the (Domino) server console it failes with HTTP Server: Error - Unable to Bind 1.2.3.4, port 80, port in use or Bind To Host configuration specifies a duplicate IP address/host a couple of times, may be 4 or 5 times then it loads without failure! And: when it comes up, I see http is listening on 80 AND 443, but SSL Connections are not working, nor any error log! It must be a kind of bad magic :-( thanks in advance Pitt

  Read the article

• How can I control which IP address IIS7 uses?

  - by brennanwstehling

  In Win2k3 I used httpcfg to tell IIS to listen to specific IP addresses on the server. I want to run Apache with VisualSVN Server on port 80 on another IP address but IIS7 binds to all ports by default. What utility for IIS7 controls the IIS7 bindings? Update: I found the answer. There is a utility called netsh. netsh http add iplisten ipaddress=xxx.xxx.xxx.xxx By default there are not IP addresses on the list so IIS7 will bind to all IP addressed. If you add one IP to the list it will listen to just that IP or any IP added to the list. It is necessary to restart IIS7 for the change to take affect.

  Read the article

• I want to hide my email address when I send an email from a Lotus Notes Group Email [closed]

  - by Shaun Casey

  Possible Duplicate: How do I change the Respond To for Group Email adresses in Notes 6.5 When I send an email from a group mail box the email shows my email address as the sender. I would like to hide my email and only show my name. I am using Notes 6.5. Could you please advise if there is a way to set up my client to do this. I want this so the receiver responds to the group email not my personal email as it may be that I am not the one to do the fillow up to the response. There are 10 people in the group email.

  Read the article

• How to get my external IP address(over NAT) from Windows command-line?

  - by Diogo Rocha

  Windows "ipconfig" command can only show me the parameters from the ethernet interfaces from my machine(even with the "ipconfig /all" argument), it can show detailed information about the interface, but will never show me my external IP address over a NAT network. However, there are several websites, such as "What is my IP" that can get and show my external IP addres. So I'm wondering, if is possible to get this value externally, should I expect that there is some way to get this information from a command line at my local machine... I need to get this value to log on an application that I'm doing with VB Script. There is some way to do this, from a "cmd" on Windows?

  Read the article

• Can I issue wireless clients with IP address on different subnet?

  - by Beanz

  We have a very standard setup with a Windows Server 2003 domain controller issuing IP addresses using DHCP. This works fine. Internet access is managed via Microsoft ISA Server 2006 Standard. Clients are required to authenticate and this works fine. We now need to provide wireless internet access to visitors for laptops, iPhones etc. We've bought a couple of Netgear access points so I was thinking we might be able to issue wireless clients connected to it with an IP address on a different subnet and then allow non-authenticated Internet access via the ISA Server for that IP range. Does that sound plausible? I'm not even sure if I can issue a different subnet to wireless clients.

  Read the article

• How to force Chrome to make bookmarks the priority for auto-complete in the address bar?

  - by NoCatharsis

  As it is right now, if I start typing, for instance, "dictionary" into the address bar, Chrome immediately returns a list of bookmarks, history, and related sites. However, the first and highlighted option is to search Google for "dictionary". I want Chrome to immediately recognize that I have a bookmark specifically named "Dictionary" that links to the site www.dictionary.com. But, that's the second choice, not the first. So I have to type a few letters, get auto-complete to suggest some sites, then key down to my bookmark item before pressing Enter. How annoying. Any way to cut the middle man and make my bookmark the top result?

  Read the article

• How can i resolve all external addresses to internal address?

  - by Darian

  I am currently setting up a Linux server for a WIFI access-point. When ever someone who is connected to the hotspot/access-point? tries to reload a page they get forced onto the one page. Note: this wont have internet access! ie: user tries accessing www.google.com = it returns 192.168.1.200 or example.domain I've read that "dnsmasq" can be used to redirect any external addresses to an internal address. but haven't had any luck. Anyone have an example of a config for "dnsmasq"? I have also read that this can be done through a proxy?

  Read the article

• How to configure multiple iSCSI Portal Groups on a EqualLogic PS6100?

  - by kce

  I am working on a migration from a VMware vSphere environment to a Hyper-V Cluster utilizing Windows Server 2012 R2. The setup is pretty small, an EqualLogic PS6100e and two Dell PowerConnect 5424 switches and handful of R710s and R620s. The SAN was configured as a non-RFC1918 network that is not assigned to our organization and since I am working on building a new virtualization environment I figured that this would be an appropriate time to do a subnet migration. I configured a separate VLAN and subnet on the switches and the two previously unused NICs on the PS6100's controllers. At this time I only have a single Hyper-V host cabled in but I can successfully ping the PS6100 from the host. From the PS6100 I can ping each of the four NICs that currently on the storage network. I cannot connect the Microsoft iSCSI Initiator to the Target. I have successfully added the Target Portals (the IP addresses of PS6100 NICs) and the Targets are discovered but listed as inactive. If I try to Connect to them I get the following error, "Log onto Target - Connection Failed" and ISCSIPrt 1 and 70 events are recorded in the Event Log. I have verified that access control to the volume is not the problem by temporarily disabling it. I suspect the problem is with the Portal Group IP address which is still listed as Group Address of old subnet (I know, I know I might be committing the sin of the X/Y problem but everything else looks good): RFC3720 has this to say about Network Portal and Portal Groups: Network Portal: The Network Portal is a component of a Network Entity that has a TCP/IP network address and that may be used by an iSCSI Node within that Network Entity for the connection(s) within one of its iSCSI sessions. A Network Portal in an initiator is identified by its IP address. A Network Portal in a target is identified by its IP address and its listening TCP port. Portal Groups: iSCSI supports multiple connections within the same session; some implementations will have the ability to combine connections in a session across multiple Network Portals. A Portal Group defines a set of Network Portals within an iSCSI Network Entity that collectively supports the capability of coordinating a session with connections spanning these portals. Not all Network Portals within a Portal Group need participate in every session connected through that Portal Group. One or more Portal Groups may provide access to an iSCSI Node. Each Network Portal, as utilized by a given iSCSI Node, belongs to exactly one portal group within that node. The EqualLogic Group Manager documentation has this to say about the Group IP Address: You use the group IP address as the iSCSI discovery address when connecting initiators to iSCSI targets in the group. If you modify the group IP address, you might need to change your initiator configuration to use the new discovery address Changing the group IP address disconnects any iSCSI connections to the group and any administrators logged in to the group through the group IP address. Which sounds equivalent to me (I am following up with support to confirm). I think a reasonable explanation at this point is that the Initiator can't complete the connection to the Target because the Group IP Address / Network Portal is on a different subnet. I really want to avoid a cutover and would prefer to run both subnets side-by-side until I can install and configure each Hyper-V host. Question/s: Is my assessment at all reasonable? Is it possible to configure multiple Group IP Addresses on the EqualLogic PS6100? I don't want to just change it as it will disconnect the remaining ESXi hosts. Am I just Doing It Wrong(TM)?

  Read the article

• How to Configure IIS 7.5 to Host Several Classic ASP Sites using 1 IP Address?

  - by SidC

  We are running Windows Server 2008 R2 with IIS 7.5 and have 4-5 Classic ASP sites to install. The main site is stored in wwwroot and the other sites are stored in folders below wwwroot. We have 1 IP address for the server. How do I configure IIS to allow folks to browse/test the sites before domain names are pointed to te server? When I setup one of the sites in a subfolder of wwwroot and assign a separate port to it, I receive a message stating: Config Error Cannot add duplicate collection entry of type 'add' with unique key attribute 'value' set to 'index.asp' How do I remedy this error and permit IIS to render the site?

  Read the article

• What could cause Citrix Xenapp to stop streaming applications after the server's IP address changed?

  - by Ken Pespisa

  We have a Citrix XenApp 5.0 server running on Windows 2008, and today we moved ISPs so our IP addresses changed. The IP addresses have propagated, the XenApp server is running, and internally we can connect to the server, choose an app, and have it streamed without issue. Externally we are only able to authenticate to the server and choose an app, but the app never launches in the client. I'm guessing there's a hand-off between the part of XenApp that authenticates a user and shows what apps they can launch, and the part that does the app streaming, and that second part is hard-coded to use an the old ip address. Any ideas why this could be happening?

  Read the article

• How can I shrink the Address toolbar in the Task Bar?

  - by Iszi

  I like being able to run commands straight from my Task Bar. So, I've enabled the Address toolbar on my new Windows 7 system - just like I had on my old XP system. However, the bar seems to have a mandatory minimum length that's a bit longer than I'd prefer. It's about twice as long, if memory serves, as the minimum size allowed in XP. Is there any way I can adjust this minimum length, through a Registry key or some other means? (Note: I've also got a related question, about removing the Refresh button at the end of the bar.) EDIT: For clarity, I'm adding a screenshot. The toolbar I want to shorten is the one circled below, with an empty text-entry field that has a drop-down and "Refresh" button. I currently have it positioned between a Quick Launch toolbar and the Taskbar. On the far side of the Taskbar, before the System Tray, is a Desktop toolbar.

  Read the article

• How to associate a domain name and IP address?

  - by StackedCrooked

  The situation is as follows: I am renting a dedicated server using SliceHost. On this server I have installed a small HTTPServer. I can verify that it works by nativating directly to its IP address (example). I have also purchased a domain name from gandi.net and would like to link it with to my server. However, I'm having much trouble finding clear instructions on how to create this link. After a few hours of reading documentation and trying out things I ended up the following configuration. on the DNS registrar I have specified the following settings: on the Slicehost server I specified these "records": But it doesn't seem to work. I end up on this page telling me the domain name is not available. Does anyone have an idea what I am doing wrong?

  Read the article

• Why my laptop sends ARP request to itself ?

  - by user58859

  I have just started to learn about protocols. While studying the packets in wireshark, I came across a ARP request sent by my machine to my own IP. Here is the details of the packet : No. Time Source Destination Protocol Info 15 1.463563 IntelCor_aa:aa:aa Broadcast ARP Who has 192.168.1.34? Tell 0.0.0.0 Frame 15: 42 bytes on wire (336 bits), 42 bytes captured (336 bits) Arrival Time: Jan 7, 2011 18:51:43.886089000 India Standard Time Epoch Time: 1294406503.886089000 seconds [Time delta from previous captured frame: 0.123389000 seconds] [Time delta from previous displayed frame: 0.123389000 seconds] [Time since reference or first frame: 1.463563000 seconds] Frame Number: 15 Frame Length: 42 bytes (336 bits) Capture Length: 42 bytes (336 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:arp] [Coloring Rule Name: ARP] [Coloring Rule String: arp] Ethernet II, Src: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa), Dst: Broadcast (ff:ff:ff:ff:ff:ff) Destination: Broadcast (ff:ff:ff:ff:ff:ff) Address: Broadcast (ff:ff:ff:ff:ff:ff) .... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) Source: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) Type: ARP (0x0806) Address Resolution Protocol (request) Hardware type: Ethernet (0x0001) Protocol type: IP (0x0800) Hardware size: 6 Protocol size: 4 Opcode: request (0x0001) [Is gratuitous: False] Sender MAC address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Sender IP address: 0.0.0.0 (0.0.0.0) Target MAC address: 00:00:00_00:00:00 (00:00:00:00:00:00) Target IP address: 192.168.1.34 (192.168.1.34) Here the sender's mac address is mine(Here I have hiden my mac address). target IP is mine. Why my machine is sending ARP request to itself? I found 3 packets of this type. There was no ARP reply for these packets. Can anybody explain me why it is? (My operating system is windows-7. I am directly connected to a wifi modem. I got these packets as soon as I started my connection.) I want one suggestion also. many places I read that RFC's are enough for study about protocols. I studied the RFC 826 on ARP. I personally feel that is not enough at all. Any suggestion regarding this? Is there more then 1 RFC for a protocol? I want to study about the protocols in very detail. Can anybody guide me for this? Thanks in advance.

  Read the article

• OS X Address Not Available - How do I open this port?

  - by GeoffreyF67

  I am trying to get xdebug working on my snow leopard box. It uses port 9000. When I ask slickedit to monitor this port is gives an error that the address is not available. I've gone to canyouseeme.org to see if the port is open. It says the port is NOT open. I've verified that I have that port forwarding to my box from the router and i do NOT have the mac firewall running. I'm stumped. Any ideas?

  Read the article

• What are some good, IP Address Management solutions for IPv6? [closed]

  - by Russell Heilling

  There are a number of open source IPAM tools available for IPv4 address management; however there seems to be a distinct lack of actively updated tools available for IPv6. Other than FreeIPdb (code no longer maintained) or the RIPE Database (I have seen some customisations to the RIPEdb that allow for enterprise/ISP IPAM but it seems like overkill for a system that will probably only ever handle one /32 worth of space). Are there any other options that I'm missing? (Database only please. I know vi can be used for flat text IPAM, that's how I'm handling our /32 at the moment, but I don't see it scaling for much longer) It doesn't have to be open source but what are folks doing to manage IPv6 in a dual stack environment

  Read the article

• How do I remove the Refresh button from the Address toolbar?

  - by Iszi

  I like being able to run commands straight from my Task Bar. So, I've enabled the Address toolbar on my new Windows 7 system - just like I had on my old XP system. However, the bar seems to have a mandatory minimum length (I've posted a separate question about that) that's a bit longer than I'd prefer. Additionally, a bit more horizontal space is consumed by a Refresh button at the end of it. This Refresh button appears similar to the Go button that used to show by default in older versions. That button was easily removed by changing a registry value that doesn't seem to exist in Windows 7. Is there a similar registry hack I can use to remove the new Refresh button?

  Read the article

• How to add a broadcast address to loopback with ifconfig on a OS/X?

  - by chrisapotek

  I am trying to use ifconfig to turn on broadcast on my loopback interface. It currently reads: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 As you can see, no broadcast address! :( :( :( I tried this on OS/X but it did not work and it did not give any error or feedback: ifconfig lo0 broadcast 127.255.255.255 Any guru would know that? I have one server that sends one packet. I have two clients running on the same machine as the server. I need them to pick up the packet WITHOUT having to force the server to send it twice.

  Read the article

• How to make OS X send LOCAL IP address in www request headers?

  - by Louis W

  I need to be able to send the local IP address of a computer along with the headers when making requests to a website. Similar to the way you can get the _SERVER["REMOTE_ADDR"] in php, but the local ip (e.g. 192.168.100.1) This will be an intranet so the environment can be controlled. Anything can be installed on the computer, etc. This will be on a Mac OS X computer. Hoping for both Safari AND Firefox. But would be open to using one one. Does anyone know if this is possible? Thanks so much.

  Read the article

• MPLS basic configuration

  - by Vineet Menon

  I want to test out MPLS VPN in my lab. I have 3 routers. 2 PEs and 1P router, all cisco 2921. Something like this, ----- ---- ----- | PE1 |.1____192.168.1.0____.2| P |.2____192.168.2.0____.1| PE2 | | | | | | | ----- ---- ----- lo0:10.1.1.1 lo0:10.1.1.2 lo0:10.1.1.3 Here's the configuration file for each of them, PE1 router hostname PE1 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! interface Loopback0 ip address 10.1.1.1 255.255.255.255 ! interface GigabitEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.1.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.3 remote-as 100 neighbor 10.1.1.3 update-source Loopback0 neighbor 172.16.1.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.3 activate neighbor 10.1.1.3 send-community extended exit-address-family For P router: hostname P ! no ipv6 cef ip source-route ip cef ! interface Loopback0 ip address 10.1.1.2 255.255.255.255 ! interface GigabitEthernet0/1 ip address 192.168.1.2 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/2 ip address 192.168.2.2 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.2 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 ! For PE2 router: ! hostname PE2 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! ! interface Loopback0 ip address 10.1.1.3 255.255.255.0 ! interface GigabitEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.2.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.3 0.0.0.0 area 0 network 192.168.2.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.1 remote-as 100 neighbor 10.1.1.1 update-source Loopback0 neighbor 172.16.2.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.1 activate neighbor 10.1.1.1 send-community extended exit-address-family ! I am following this article form cisco. But things are not working properly. Any help would be appreciated.

  Read the article

• Best way to block a country by IP address?

  - by George Edison

  I have a website that needs to block a particular country based on IP address. I am more than aware that IP-based blocking is not a foolproof method for blocking visitors, but it is a necessary step in the right direction. Since I'm using PHP, what I would do is use a GeoIP database like geoplugin.net. However, I'm curious to know if there's a better way of doing this. The website is on a shared webserver (I don't have root access) and it is running Apache on centOS. I guess my question is "can an .htaccess file be configured to block by IP using an external source to lookup IP addresses."

  Read the article

• Can't copy Ilias-folder via FQDN, but via ip-address?

  - by Lars

  I have an Ilias-Installation, which is available through two virtual hosts: the FQDN and the ip-address. The first server is ssl only, the second plain http. Both configuration files look the same except for the SSL-part: SSLEngine on SSLCertificateFile /etc/apache2/ssl/ilias.pem In the Ilias-Webinterface, I can copy a folder on the plain http. But if I try to copy the same folder on the ssl virtual host, I get the notice, that the copy was started (rough german translation here), but the folder does not show up. There are no errors in the error-logs of php or the webserver and as said, no differences beside the ssl-part. The guys at an ilias-forum did not have an idea, either. Any ideas in here?

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >