Search Results

Search found 3935 results on 158 pages for 'garreth 00'.

Page 73/158 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• LXC container can only access host via bridge

  - by vitaut

  I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

  Read the article

• Targus USB-to-RS232 not working with Linux?

  - by Ethan Leroy

  I have the Targus PA088 USB to RS232 converter, but it seems that it does not work with linux. Its RX and TX lights are flashing, but I can't see the data in minicom/picocom. When using it with Windows and hterm, everything's fine. Any idea what could be the problem? Additional info: When I plug in the adapter, I can see the following messages in /var/log/messages.log Nov 25 01:47:31 localhost kernel: [ 831.787066] usb 2-1.1: new full speed USB device number 5 using ehci_hcd Nov 25 01:47:32 localhost kernel: [ 832.554810] mct_u232 2-1.1:1.0: MCT U232 converter detected Nov 25 01:47:32 localhost kernel: [ 832.555002] usb 2-1.1: MCT U232 converter now attached to ttyUSB0 Nov 25 01:47:32 localhost mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1" Nov 25 01:47:32 localhost mtp-probe: bus: 2, device: 5 was not an MTP device

  Read the article

• USB Flash not recognised by Windows and BIOS, but works fine in Linux

  - by bbalegere

  I have a Transcend JetFLash 2GB USB Drive.It was working fine and I had been using it occasionally. All of sudden it stopped working in all versions of Windows . The USB Drive is also not recognised by the BIOS.It does not show in the list of bootable devices.(It used show up in the list earlier) However the USB Drive works fine in my Linux Mint 11 OS. Running dmesg gives this [ 941.812192] usb 1-2: new high speed USB device using ehci_hcd and address 4 [ 941.936178] usb 1-2: device descriptor read/64, error -71 [ 942.164188] usb 1-2: device descriptor read/64, error -71 [ 942.380189] usb 1-2: new high speed USB device using ehci_hcd and address 5 [ 942.504138] usb 1-2: device descriptor read/64, error -71 [ 942.732179] usb 1-2: device descriptor read/64, error -71 [ 942.948154] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 943.364134] usb 1-2: device not accepting address 6, error -71 [ 943.476172] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 943.892140] usb 1-2: device not accepting address 7, error -71 [ 943.892191] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 944.296190] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 944.438251] usb 2-2: not running at top speed; connect to a high speed hub [ 944.709928] usbcore: registered new interface driver uas [ 944.729999] Initializing USB Mass Storage driver... [ 944.730509] scsi6 : usb-storage 2-2:1.0 [ 944.730908] usbcore: registered new interface driver usb-storage [ 944.730917] USB Mass Storage support registered. [ 945.736320] scsi 6:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2 [ 945.744547] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 945.753316] sd 6:0:0:0: [sdb] 3944448 512-byte logical blocks: (2.01 GB/1.88 GiB) [ 945.758274] sd 6:0:0:0: [sdb] Write Protect is off [ 945.758288] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 945.765167] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.765181] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 945.784309] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.784323] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.239512] sdb: sdb1 [ 946.257279] sd 6:0:0:0: [sdb] No Caching mode page present [ 946.257292] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.257302] sd 6:0:0:0: [sdb] Attached SCSI removable disk Looks like there is something wrong the USB Drive.It is not recognised in any computer running Windows. Is there any way to fix this? Any idea why this problem occurred ?

  Read the article

• Trying to rename a computer via the netdom command and force a reboot

  - by user57020

  Why doesn't this work? it looks like it will but nothing happens. Option Explicit Dim wshNetwork Dim wshShell Dim PCname Dim Newname Set wshNetwork = WScript.CreateObject("WScript.Network") Set wshShell = WScript.CreateObject("WScript.Shell") PCname = InputBox("Type in the name of the pc you want to rename") Newname = InputBox("Type in the name of the new pc name") wshShell.run("netdom renamecomputer " &PCname& " /NewName:"&Newname& " /reboot:00 " ) 'MsgBox("netdom renamecomputer " &PCname& " /NewName:"&Newname& " /reboot:00 /y")

  Read the article

• Error 502 in OpenOfficeSpreadsheet formula

  - by cody

  The formula failing is the following: =IF(TIMEVALUE(C2 & ":00") > TIMEVALUE(B2 & ":00"); 0; C2-B2) I previously tried =IF(C2 > B2; 0; C2-B2) but this also gives me "Error 502". The cells it is referring to contains data in the format "12:30" (I formatted the columns with format "HH:MM"). I just want to calculate how much time lies between two times, respecting the special case where endtime < starttime.

  Read the article

• My VPS Server's TimeZone always resets on reboot - Why?

  - by GenericTypeTea

  I'm using a VPS running Virtuozzo Containers with Parallels. Every time I reboot it sets the server's TimeZone to GMT+01 Amsterdam. If I change that to GMT+00 London and then reboot, it gets set back to Amsterdam again. Is there any way I can prevent this? I'm also have a very strange issue whereby .Net is reporting that the DateTime.Now as the +01 Amsterdam time instead of +00 GMT, even after I've change it to London's TimeZone. Is there somewhere else I need to change the TimeZone apart from in the Timezone tab under the system clock?

  Read the article

• Linux - use dhcp again to get IP

  - by Markus Orreilly

  I had statically set my ip in Linux using: sudo ifconfig eth0 192.168.blah.blah Now I want it to go back to using DHCP to assign the IP. How do I do that? This is what I see when I run dhclient Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/eth0/08:00:27:9b:43:09 Sending on LPF/eth0/08:00:27:9b:43:09 Sending on Socket/fallback DHCPREQUEST of 192.168.56.104 on eth0 to 255.255.255.255 port 67

  Read the article

• With CentOS 6 and LXC, "ifconfig" is unable to see network interface (but busybox "ifconfig" works fine)

  - by larsks

  I've just started working with LXC under CentOS 6 (via the libvirt adapter). If I create an LXC container, I'm unable to see any network interfaces when using the native system tools: # ifconfig -a # The behavior is very odd; specifying an interface by names yields neither the expected output nor an error message. This is true even for clearly invalid interface names, like this: # ifconfig foo # The ip command exhibits the same behavior. On the other hand, if I use "ifconfig" provided by busybox, everything works as expected: # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:268 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17814 (17.3 KiB) TX bytes:552 (552.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So...what does busybox know that the native tools don't? The libvirt config for this environment is pretty standard; the network definition looks like this: <interface type='network'> <mac address='52:54:00:e0:12:c8'/> <source network='default'/> <target dev='veth0'/> </interface> The full configuration is here if you think it might help. I'm running: lxc-0.7.2-2.el6.x86_64 kernel-2.6.32-71.29.1.el6.x86_64 EDIT Weirder and weirder...it's a display issue, not a functionality issue. I can see the output of ifconfig if I pipe it into anything, so for example: # ifconfig eth0 | cat eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:573 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37914 (37.0 KiB) TX bytes:552 (552.0 b) And in fact even when not piping the output, strace shows that ifconfig is in fact writing the output to file descriptor 1 (aka stdout), so it's not clear why no output is actually showing up. This could be either an LXC or a virsh issue, I guess.

  Read the article

• Task Manager does not show memory usage

  - by Robin

  I just noticed this yesterday. I selected different memory columns, none of them worked, and I've tried showing processes from all users. I'm using Win 7. It doesn't slow down my computer or does anything else. I just want to know why and how to fix it. Could anyone help me on this? Thank you cannot post pix :( it is like this: only shows K, without actual number Image Name--------User Name----CPU----Memory (Private Working Set)------Description System -----------SYSTEM ------01-------------------------------K-------NT Kernel &system Smss.exe--------- SYSTEM -----00-------------------------------K-------Win Session Manager Wininit.exe------ SYSTEM ------00-------------------------------K-------Win Start-up Applic It's pretty much the same as http://www.sevenforums.com/general-discussion/56891-my-task-manager-doesnt-show-ram-usage-each-program.html that is the only one i found on google.

  Read the article

• Unable to locate Windows Server Error log files

  - by Sam007

  I am getting an error in my application on 500 Internal Server Error. The firebug gives me, NetworkError: 500 Internal Server Error - http://webgis.arizona.edu/ArcGIS/rest/services/webGIS/Shock_Models/GPServer/Income_Log/jobs/jc09c501156564f71abc5d98393581267/results/final_shp?dpi=96&transparent=true&format=png8&imageSR=102100&f=image&bbox=%7B%22xmin%22%3A-14519891.438356264%2C%22ymin%22%3A637618.0139790997%2C%22xmax%22%3A-6692739.741956295%2C%22ymax%22%3A6507981.786279075%2C%22spatialReference%22%3A%7B%22wkid%22%3A102100%7D%7D&bboxSR=102100&size=800%2C600 And when I goto that particular link, I get this error, Server Error - Object reference not set to an instance of an object. Any idea how I can correct it? UPDATE I was told to use fiddler and see the error details that is occurring over the network and this is the output that I got, SESSION STATE: Done. Response Entity Size: 849 bytes. == FLAGS ================== BitFlags: [ClientPipeReused, ServerPipeReused] 0x18 X-CLIENTPORT: 2010 X-RESPONSEBODYTRANSFERLENGTH: 849 X-EGRESSPORT: 2023 X-HOSTIP: 128.196.53.161 X-PROCESSINFO: firefox:2248 X-CLIENTIP: 127.0.0.1 X-SERVERSOCKET: REUSE ServerPipe#2 == TIMING INFO ============ ClientConnected: 15:53:51.383 ClientBeginRequest: 15:53:51.494 GotRequestHeaders: 15:53:51.494 ClientDoneRequest: 15:53:51.494 Determine Gateway: 0ms DNS Lookup: 0ms TCP/IP Connect: 0ms HTTPS Handshake: 0ms ServerConnected: 15:52:45.077 FiddlerBeginRequest: 15:53:51.495 ServerGotRequest: 15:53:51.495 ServerBeginResponse: 15:53:51.679 GotResponseHeaders: 15:53:51.679 ServerDoneResponse: 15:53:51.679 ClientBeginResponse: 15:53:51.679 ClientDoneResponse: 15:53:51.679 Overall Elapsed: 00:00:00.1850106 The response was buffered before delivery to the client. == WININET CACHE INFO ============ This URL is not present in the WinINET cache. [Code: 2] * Note: Data above shows WinINET's current cache state, not the state at the time of the request. * Note: Data above shows WinINET's Medium Integrity (non-Protected Mode) cache only. But I am still confused as to what the error is? This is the application. I am not sure if the error is due to the ArcGIS-Server or the Windows Server 2008. I am new on working with the Windows Server and wanted to know where can I look for the error lof files? This is the link which gives the details and the log info of the job executed. This is the output.

  Read the article

• Ubuntu 10.04 not detecting multiple monitors

  - by razass

  I have 2 graphics cards, the output from the lspci: 01:00.0 VGA compatible controller: ATI Technologies Inc RV770 [Radeon HD 4850] 02:00.0 VGA compatible controller: ATI Technologies Inc RV710 [Radeon HD 4350] I have one monitor connected to the 4850 and 2 connected to the 4350. However when I go into System Preferences Monitors the only monitor shown is the one connected to the 4850. Is there something I need to enable for it to be able to use the other card? How do I get this to work. Thanks.

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files

  - by yegor

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• exchange server 2010 Outlook Web Access - Exchange Control Panel WEB Interface

  - by Aceth

  from what i can gather the mailbox bit of the web interface works fine.. when any of the users go to options (top right) and try to use some of the features such as the Organise Mail Delivery Reports to find messages etc... it comes up with a message .. "An item with the same key has already been added" I've looked in the event viewer and i think its this error - Watson report about to be sent for process id: 7016, with parameters: E12IIS, c-RTL-AMD64, 14.00.0639.021, ECP, ECP.Powershell, https://x.x.x.x/ecp/PersonalSettings/Accounts.svc/GetList, UnexpectedCondition:ArgumentException, c09, 14.00.0639.021. ErrorReportingEnabled: False and Request for URL 'https://x.x.x.x/ecp/PersonalSettings/Accounts.svc/GetList' failed with the following error: System.ArgumentException: An item with the same key has already been added. at System.ServiceModel.AsyncResult.End[TAsyncResult](IAsyncResult result) at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.End(IAsyncResult result) at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.ExecuteSynchronous(HttpApplication context, Boolean flowContext) at Microsoft.Exchange.Management.ControlPanel.WebServiceHandler.ProcessRequest(HttpContext context) at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) I've tried googling but no luck that's relevant :(

  Read the article

• Apache on Mac Mavericks issue

  - by Michael

  Trying to run Apache so that I can create a testing server on my mac.When I start apache it starts, but it doesn't run (no connection to local host. Ill upload the unix,you'll see that after starting there is no processes, and I did a check to show you what was running on my port 80... I don't entirely know that means. Michaels-MacBook-Pro-3:~ michaelramos$ sudo apachectl start Michaels-MacBook-Pro-3:~ michaelramos$ ps aux | grep httpd michaelramos 348 0.0 0.0 2442000 624 s000 S+ 8:51AM 0:00.00 grep httpd Michaels-MacBook-Pro-3:~ michaelramos$ sudo apachectl start org.apache.httpd: Already loaded Michaels-MacBook-Pro-3:~ michaelramos$ sudo lsof -i ':80' COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME ocspd 96 root 18u IPv4 0x8402f926599c58df 0t0 TCP dhcp-92-67.radford.edu:49267->108.162.232.196:http (ESTABLISHED) ocspd 96 root 20u IPv4 0x8402f926599c58df 0t0 TCP dhcp-92-67.radford.edu:49267->108.162.232.196:http (ESTABLISHED) ocspd 96 root 21u IPv4 0x8402f926599c50f7 0t0 TCP dhcp-92-67.radford.edu:49268->108.162.232.206:http (ESTABLISHED) ocspd 96 root 23u IPv4 0x8402f926599c50f7 0t0 TCP dhcp-92-67.radford.edu:49268->108.162.232.206:http (ESTABLISHED)

  Read the article

• Solaris mounting partitions

  - by Benco

  I'm trying to mount a partition in solaris 10... bash-3.00# mount /dev/dsk/c0t0d0s3 /data mount: /dev/dsk/c0t0d0s3 is already mounted or /data is busy As far as I know c0t0d0s3 isn't already mounted elsewhere, so what's really going on here? From /etc/mnttab : /dev/dsk/c1t0d0s0 / ufs rw,intr,largefiles,logging,xattr,onerror=panic,dev=7800001285811136 /devices /devices devfs dev=4840000 1285811125 ctfs /system/contract ctfs dev=48c0001 1285811125 proc /proc proc dev=4880000 1285811125 mnttab /etc/mnttab mntfs dev=4900001 1285811125 swap /etc/svc/volatile tmpfs xattr,dev=4940001 1285811125 objfs /system/object objfs dev=4980001 1285811125 sharefs /etc/dfs/sharetab sharefs dev=49c0001 1285811125 /usr/lib/libc/libc_hwcap1.so.1 /lib/libc.so.1 lofs dev=780000 1285811131 fd /dev/fd fd rw,dev=4b40001 1285811136 swap /tmp tmpfs xattr,dev=4940002 1285811137 swap /var/run tmpfs xattr,dev=4940003 1285811137 -hosts /net autofs nosuid,indirect,ignore,nobrowse,dev=4c00001 1285811148 auto_home /home autofs indirect,ignore,nobrowse,dev=4c00002 1285811148 cordb:vold(pid530) /vol nfs ignore,noquota,dev=4bc0001 1285811149 I suspect the problem is not related to the mount point, but rather the disk slice I'm trying to mount: bash-3.00# newfs -v /dev/dsk/c0t0d0s3 /dev/rdsk/c0t0d0s3: Device busy

  Read the article

• Rest client throw timeout exception

  - by shandu

  Hi, I have create REST client in C# using example on this page: http://msdn.microsoft.com/en-us/library/aa395208(v=vs.90).aspx. Server is built in PHP. When I send request to some urls I have this exception: The request channel timed out while waiting for a reply after 00:00:59.9531250. Increase the timeout value passed to the call to Request or increase the SendTimeout value on the Binding. The time allotted to this operation may have been a portion of a longer timeout. But, sometimes, when I debug code, I get response. How to solve this?

  Read the article

• Rest client throw timeout exception

  - by shandu

  Hi, I have create REST client in C# using example on this page: http://msdn.microsoft.com/en-us/library/aa395208(v=vs.90).aspx. Server is built in PHP. When I send request to some urls I have this exception: The request channel timed out while waiting for a reply after 00:00:59.9531250. Increase the timeout value passed to the call to Request or increase the SendTimeout value on the Binding. The time allotted to this operation may have been a portion of a longer timeout. But, sometimes, when I debug code, I get response. How to solve this?

  Read the article

• setup advanced filtering and access restrictions on dd-wrt using iptables

  - by Nova deViator

  I have a linksys WRT54GL router with a DD-WRT installed and I want to setup some advanced filtering that seem to not be available through "Access restrictions" web gui option. I guess I would be using IPTABLES then. I have ssh access to router and can run iptables, but I'm not so experienced with iptables. So here are my needs: my policy would be deny all first and then allow exceptions allow all http (port 80) access to WAN through wireless allow all other traffic only to PCs with specific MAC addresses allow internet access to PC with specific MAC address according to schedule (let's say everyday between 18:00-21:00) is this possible to setup with IPtables? could somebody help me a bit with it? or should go and RTFM?

  Read the article

• Can this USB3 behaviour be anything else than a hardware failure?

  - by Jonas Wielicki

  While my motherboard is half a year old now (ASUS M5A99X EVO), I only recently made use of the USB3 boards (after purchase of USB3 external harddrive). However, I am encountering issues. I am running linux 3.6.7-4.fc16.x86_64. Initially, the harddrive worked fine with USB3 (amazing ˜160MB/s), but I had some problems after putting after putting the harddrive to sleep manually after use (backup) with hdparm -Y. After some time, the device disappears from lsusb and i see the following in dmesg: [ 1924.091107] xhci_hcd 0000:05:00.0: xHCI host not responding to stop endpoint command. [ 1924.091114] xhci_hcd 0000:05:00.0: Assuming host is dying, halting host. [ 1924.091147] xhci_hcd 0000:05:00.0: HC died; cleaning up [ 1924.091233] usb 11-1: USB disconnect, device number 2 [ 1924.091272] sd 6:0:0:0: Device offlined - not ready after error recovery Testing with my (USB3 capable) notebook, I could not immediately reproduce the behaivour. I put the drive to sleep with hdparm -Y and waited for like an hour, but it was still listed in lsusb and responded after a few seconds delay when I tried after the hour of waiting. After an hour, on the desktop, the device would've usually vanished. Googling for this issue, I came across hints that playing around with IOMMU settings and upgrading the BIOS might help. I upgraded the BIOS and tried both with and without IOMMU enabled, got similar results. Most disturbing is, that one of the two USB 3.0 hubs sometimes also disappears from lsusb (or does not show up after boot at all). I've also heard that there are some hardware issues with ASUS USB3 ports. Applying mechanic force to the capble doesn't push the issue to one side or the other. Also, udev seems to reenumerate all devices if I plug the HDD into the USB 3.0 port without success (I can notice from my keyboard layout being changed to the default, which I do not use normally). The drive is externally powered and the external power supply is plugged in (it also stays powered when unplugging from USB, although it will spin down then). So before I try to return the board, I wanted to find out whether this can be anything else than a failure on the motherboard?

  Read the article

• ESX - Initialization for vmfs2 failed with -1

  - by ov4

  I recently purchases a bunch of R710's from Dell. I installed VMWare ESX on them. The installation process finishes without a problem; however once ESX boots the following error displays at the botton with red letters: 00:00:02:21.493 cpu11:4119) mod:2971: Initialization for vmfs2 failed with -1 I installed on two different servers and the same error appears. The curious thing is that if I install ESXi 3.5 or 4 there is not problem. What does this problem mean, and how can I resolve it?

  Read the article

• Convert shell logs (incl. escape characters) to HTML?

  - by dehmann

  Is there tool or a regexp that can convert shell escape characters to HTML code? As an example, here is a logfile from GNU screen: ^MESC[K$ ^MESC[K$ exit Executing .bashrc ESC[00;31;31mserver.xyz.com: ESC[00;34;34m~ which I would like to convert to something like this: $ exit Executing .bashrc <font color=red>server.xyz.com</font>: <font color=blue>~</font> and send as HTML e-mail to an e-mail address, to archive my work. Here is a related question, which shows how to convert it to regular text, but it would be nice to convert to HTML and not just throw the escape characters away.

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files)

  - by user11955

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• VMware postfix server drops connection

  - by nicoX

  Our physical server godzilla forwards mails to our virtuall VMware server b4. They are on the same net. Often connection drops, we can't ping godzilla with our b4. That means mails from godzilla won't reach b4 and the mails will be in handed into the mailq. Sometimes it takes some hours and the issue will auto fix itself, b4 will wake up and the mail will be delivered. Another thing if we remotely ssh into the b4, the b4 will wake up and and receive any mailq mails from godzilla and deliver them. netadmin@b4:/var/log$ arp -a ? (192.168.209.80) at 00:1E:C9:AE:79:9D [ether] on eth0 root@godzilla:/usr/local/bin# arp -a ? (192.168.209.20) at 00:50:56:91:7d:b2 [ether] on eth0

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >