Search Results

Search found 2417 results on 97 pages for 'mb'.

Page 73/97 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• Built-in network card not working?

  - by Zeeshan

  Hi, I am new to Ubuntu. I have installed Ubuntu 9.04(Jaunty). After installation I found that network card is not wokring. And id doest not list in "System Preferenes Network Connections" So , i got another card from my friend and try to search on internat about my problem but still cant find solution. Some commands output is here which may be help to solve problem root@mzeeshan-desktop:/home/mzeeshan# uname -r 2.6.28-11-generic root@mzeeshan-desktop:/home/mzeeshan# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:02:44:4a:45:12 inet addr:192.168.5.37 Bcast:192.168.5.255 Mask:255.255.255.0 inet6 addr: fe80::202:44ff:fe4a:4512/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3774 errors:0 dropped:0 overruns:0 frame:0 TX packets:3611 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4307045 (4.3 MB) TX bytes:583067 (583.0 KB) Interrupt:22 Base address:0x1000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) pan0 Link encap:Ethernet HWaddr 5e:25:17:a1:18:ac BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@mzeeshan-desktop:/home/mzeeshan# lspci 00:00.0 Host bridge: Intel Corporation Device 0069 (rev 12) 00:01.0 PCI bridge: Intel Corporation Auburndale/Havendale PCI Express x16 Root Port (rev 12) 00:19.0 Ethernet controller: Intel Corporation Device 10f0 (rev 05) 00:1a.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 1 (rev 05) 00:1c.4 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 5 (rev 05) 00:1c.6 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 7 (rev 05) 00:1c.7 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 8 (rev 05) 00:1d.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Ibex Peak LPC Interface Controller (rev 05) 00:1f.2 IDE interface: Intel Corporation Ibex Peak 4 port SATA IDE Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Ibex Peak SMBus Controller (rev 05) 00:1f.5 IDE interface: Intel Corporation Ibex Peak 2 port SATA IDE Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation GeForce 8400 GS (rev a1) 06:00.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07) 06:00.1 Input device controller: Creative Labs SB Live! Game Port (rev 07) 06:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 06:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) root@mzeeshan-desktop:/home/mzeeshan# Motherboard is Intel DP55WG. I don't know what to do next. Any help will be greatly appreciated.. Thanks

  Read the article

• Problem in installation in My Hp g4 1226se

  - by vivek Verma

  1vivek.100 Dual booting error in Hp pavilion g4 1226se Dear sir or Madam, My name is vivek verma.... I am the user of my Hp laptop which series and model name is HP PAVILION G4 1226SE........ i have purchase in the year of 2012 and month is February.....the windows 7 home basic 64 Bit is already installed in in my laptop.... Now i want to install Ubuntu 12.04 Lts or 13.10 lts..... i have try many time to install in my laptop via live CD or USB installer....and i have try many live CD and many pen drive to install Ubuntu ... but it is not done......now i am in very big problem...... when i put my CD or USB drive to boot and install the Ubuntu......my laptop screen is goes the some black (brightness of my laptop screen is very low and there is very low visibility ) and not showing any thing on my laptop screen..... and when i move the my laptop screen.....then there is graphics option in this screen to installation of the Ubuntu option......and when i press the dual boot with setting button and press to continue them my laptop is goes for shutdown after 2 or 5 minutes..... ...... and Hp service center person is saying to me our laptop hardware has no problem.....please contact to Ubuntu tech support............. show please help me if possible..... My laptop configuration is here...... Hardware Product Name g4-1226se Product Number QJ551EA Microprocessor 2.4 GHz Intel Core i5-2430M Microprocessor Cache 3 MB L3 cache Memory 4 GB DDR3 Memory Max Upgradeable to 4 GB DDR3 Video Graphics Intel HD 3000 (up to 1.65 GB) Display 35,5 cm (14,0") High-Definition LED-backlit BrightView Display (1366 x 768) Hard Drive 500 GB SATA (5400 rpm) Multimedia Drive SuperMulti DVD±R/RW with Double Layer Support Network Card Integrated 10/100 BASE-T Ethernet LAN Wireless Connectivity 802.11 b/g/n Sound Altec Lansing speakers Keyboard Full size island-style keyboard with home roll keys Pointing Device TouchPad supporting Multi-Touch gestures with On/Off button PC Card Slots Multi-Format Digital Media Card Reader for Secure Digital cards, Multimedia cards External Ports 1 VGA 1 headphone-out 1 microphone-in 3 USB 2.0 1 RJ45 Dimensions 34.1 x 23.1 x 3.56 cm Weight Starting at 2.1 kg Power 65W AC Power Adapter 6-cell Lithium-Ion (Li-Ion) What's In The Box Webcam with Integrated Digital Microphone (VGA) Software Operating System: Windows 7 Home Basic 64bit....Genuine..... ......... Sir please help me if possible....... Name =vivek verma Contact no.+919911146737 Email [email protected]

  Read the article

• Package system broken - E: Sub-process /usr/bin/dpkg returned an error code (1)

  - by delha

  After installing some packages and libraries I have an error on Package Manager, I can't run any update because it says: "The package system is broken If you are using third party repositories then disable them, since they are a common source of problems. Now run the following command in a terminal: apt-get install -f " I've tried to do what it says and it returns me: jara@jara-Aspire-5738:~$ sudo apt-get install -f Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libcaca-dev libopencv2.3-bin nite-dev python-bluez ps-engine libslang2-dev python-sphinx ros-electric-geometry-tutorials ros-electric-geometry-visualization python-matplotlib libzzip-dev ros-electric-orocos-kinematics-dynamics ros-electric-physics-ode libbluetooth-dev libaudiofile-dev libassimp2 libnetpbm10-dev ros-electric-laser-pipeline python-epydoc ros-electric-geometry-experimental libasound2-dev evtest python-matplotlib-data libyaml-dev ros-electric-bullet ros-electric-executive-smach ros-electric-documentation libgl2ps0 libncurses5-dev ros-electric-robot-model texlive-fonts-recommended python-lxml libwxgtk2.8-dev daemontools libxxf86vm-dev libqhull-dev libavahi-client-dev ros-electric-geometry libgl2ps-dev libcurl4-openssl-dev assimp-dev libusb-1.0-0-dev libopencv2.3 ros-electric-diagnostics-monitors libsdl1.2-dev libjs-underscore libsdl-image1.2 tipa libusb-dev libtinfo-dev python-tz python-sip libfltk1.1 libesd0 libfreeimage-dev ros-electric-visualization x11proto-xf86vidmode-dev python-docutils libvtk5.6 ros-electric-assimp x11proto-scrnsaver-dev libnetcdf-dev libidn11-dev libeigen3-dev joystick libhdf5-serial-1.8.4 ros-electric-joystick-drivers texlive-fonts-recommended-doc esound-common libesd0-dev tcl8.5-dev ros-electric-multimaster-experimental ros-electric-rx libaudio-dev ros-electric-ros-tutorials libwxbase2.8-dev ros-electric-visualization-common python-sip-dev ros-electric-visualization-tutorials libfltk1.1-dev libpulse-dev libnetpbm10 python-markupsafe openni-dev tk8.5-dev wx2.8-headers freeglut3-dev libavahi-common-dev python-roman python-jinja2 ros-electric-robot-model-visualization libxss-dev libqhull5 libaa1-dev ros-electric-eigen freeglut3 ros-electric-executive-smach-visualization ros-electric-common-tutorials ros-electric-robot-model-tutorials libnetcdf6 libjs-sphinxdoc python-pyparsing libaudiofile0 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: libcv-dev The following NEW packages will be installed libcv-dev 0 upgraded, 1 newly installed, 0 to remove and 4 not upgraded. 2 not fully installed or removed. Need to get 0 B/3,114 kB of archives. After this operation, 11.1 MB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 261801 files and directories currently installed.) Unpacking libcv-dev (from .../libcv-dev_2.1.0-7build1_amd64.deb) ... dpkg: error processing /var/cache/apt/archives/libcv-dev_2.1.0-7build1_amd64.deb (-- unpack): trying to overwrite '/usr/bin/opencv_haartraining', which is also in package libopencv2.3-bin 2.3.1+svn6514+branch23-12~oneiric dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/libcv-dev_2.1.0-7build1_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) I've tried everything people recommend on internet like: sudo apt-get clean sudo apt-get autoremove sudo apt-get update sudo apt-get upgrade sudo apt-get -f install Also I've tried to install the synaptic manager but it doesn't let me install anything.. As you can see nothing works so I'm desperate! I'm using ubuntu 11.10, 64 bits Thanks!!

  Read the article

• NetBeans Podcast 62

  - by TinuA

  Download mp3: 49 minutes – 39.5 MB Subscribe to the NetBeans Podcast on iTunes NetBeans Community News with Geertjan and Tinu What's NEW? Recap of a SUCCESSFUL NetBeans Community Day at JavaOne2012! Want to know what you missed? Download slides for: NetBeans Community Keynote NetBeans and JavaFX panel NetBeans and Java EE panel NetBeans Platform panel Visit the JavaOne Content Catalog for slides, and audio and video recordings of all NetBeans sessions at JavaOne 2012. (Type in keyword "NetBeans".) NetBeans Governance Board elections are done. Congratulations to Anton Epple and Hermien Pellissier, the new members of the 20th Board! How would you grade the NetBeans team on NetBeans IDE 7.2? Take the NetBeans 7.2 Satisfaction Survey. NetBeans IDE 7.3 Beta 2 is available for download. The first beta debuted at JavaOne with support for HTML5. Watch videos of HTML5 support in NetBeans and visit Geertjan's blog for a beginner's guide to HTML5 development. It's a busy Fall on the NetBeans Calendar with stops at Devoxx 2012, JavaOne Latin America, Jay Day Munich, Jay Days Sweden  JavaOne 2012 Reflections NetBeans had a fantastic showing at JavaOne 2012--from the full-day lineup of NetBeans Community Day to the numerous BOFs, Labs, and sessions at the main conference. But better to hear it in these short interviews with members of the community who attended JavaOne 2012. Veteran attendees and first-timers, panel participants and award winners, the interviewees share their experience of the conference, from highlights and insights, to new discoveries and inspiration. Listen in to why attending JavaOne is a tech pilgrimage every Java developer ought to make.   07:50   Anton Epple - Eppleton Consulting (Germany); Recipient of 2012 NetBeans Community Recognition Award 17:10   Henry Arousell and Thomas Boqvist - Bjorn Lunden Information (Sweden) 24:45   Glenn Holmer - Weyco Group, Inc. (USA); Recipient of 2012 NetBeans Community Recognition Award 33:09   Timon Veenstra - Agrosense (The Netherlands); 2012 Duke's Choice Award winner (Agrosense in the Nov/Dec '12 issue of Java Magazine.) 40:19   Rob Terplowski, - Linden, Inc. (USA) More thoughts about NetBeans Day and JavaOne can also be found in two recent NetBeans Zone articles: "Reflections on JavaOne 2012 by the NetBeans Community: Part 1 and Part 2". *Have ideas for NetBeans Podcast topics? Send them to nbpodcast at netbeans dot org. *Subscribe to the official NetBeans page on Facebook! Check us out as well on Twitter, YouTube, and Google+.

  Read the article

• Very very slow transfer speeds between Windows 7 and samba server running on Ubuntu 11.10/12.04 minimal

  - by kuzyt

  As mentioned in the title I tried transferring files between Windows 7 and the samba server running on both Ubuntu 11.10 and 12.04 but both showed very slow transfer speeds. Can someone please guide me in the right direction to debug this problem ? wget --output-document=/dev/null http://tokyo1.linode.com/100MB-tokyo.bin --2012-08-21 22:02:17-- http://tokyo1.linode.com/100MB-tokyo.bin Resolving tokyo1.linode.com (tokyo1.linode.com)... 106.187.33.12 Connecting to tokyo1.linode.com (tokyo1.linode.com)|106.187.33.12|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 104857600 (100M) [application/octet-stream] Saving to: `/dev/null' 8% [=============> ] 8,923,980 64.8K/s eta 15m 0s wlan0 IEEE 802.11abgn ESSID:"TNET" Mode:Managed Frequency:2.462 GHz Access Point: 58:6D:8F:26:20:7A Bit Rate=117 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=57/70 Signal level=-53 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:101 Invalid misc:2448 Missed beacon:0 03:00.0 Network controller: Atheros Communications Inc. AR9300 Wireless LAN adaptor (rev 01) Subsystem: Atheros Communications Inc. Device 3112 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=128K] Expansion ROM at fea20000 [disabled] [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/4 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- Capabilities: [300 v1] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: ath9k Kernel modules: ath9k

  Read the article

• JRockit Virtual Edition Debug Key

  - by changjae.lee

  There are a few keys that can help the debugging of the JRVE env in console. you can type in each keys in JRVE console to see what's happening under the hood. key '0' : System information key '5' : Enable shutdown key '7' : Start JRockit Management Server (port 7091) key '8' : Statistics Counters key '9' : Full Thread Dump key '0' : Status of Debug-key Below is the sample out from each keys. Debug-key '1' pressed ============ JRockitVE System Information ============ JRockitVE version : 11.1.1.3.0-67-131044 Kernel version : 6.1.0.0-97-131024 JVM version : R27.6.6-28_o-125824-1.6.0_17-20091214-2104-linux-ia32 Hypervisor version : Xen 3.4.0 Boot state : 0x007effff Uptime : 0 days 02:04:31 CPU : uniprocessor @2327 Mhz CPU usage : 0% ctx/s: 285 preempt/s: 0 migrations/s: 0 Physical pages : 82379/261121 (321/1020 MB) Network info : 10.179.97.64 (10.179.97.64/255.255.254.0) GateWay : 10.179.96.1 MAC address : 00:16:3e:7e:dc:78 Boot options : vfsCwd : /application/user_projects/domains/wlsve_domain mainArgs : java -javaagent:/jrockitve/services/sshd/sshd.jar -cp /jrockitve/jrockit/lib/tools.jar:/jrockitve/lib/common.jar:/application/patch_wls1032/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/application/wlserver_10.3/server/lib/weblogic.jar -Dweblogic.Name=WlsveAdmin -Dweblogic.Domain=wlsve_domain -Dweblogic.management.username=weblogic -Dweblogic.management.password=welcome1 -Dweblogic.management.GenerateDefaultConfig=true weblogic.Server consLog : /jrockitve/log/jrockitve.log mounts : ext2 / dev0; posixLocale : en_US posixTimezone : Asia/Seoul posixEncoding : ISO-8859-1 Local disk : Size: 1024M, Used: 728M, Free: 295M ======================================================== Debug-key '5' pressed Shutdown enabled. Debug-key '7' pressed [JRockit] Management server already started. Ignoring request. Debug-key '8' pressed Starting stat recording Debug-key '8' pressed ========= Statistics Counters for the last second ========= dev.eth0_rx.cnt : 22 packets dev.eth0_rx_bytes.cnt : 2704 bytes dev.net_interrupts.cnt : 22 interrupts evt.timer_ticks.cnt : 123 ticks hyper.priv_entries.cnt : 144 entries schedule.context_switches.cnt : 271 switches schedule.idle_cpu_time.cnt : 997318849 nanoseconds schedule.idle_cpu_time_0.cnt : 997318849 nanoseconds schedule.total_cpu_time.cnt : 1000031757 nanoseconds time.system_time.cnt : 1000 ns time.timer_updates.cnt : 123 updates time.wallclock_time.cnt : 1000 ns ======================================= Debug-key '9' pressed ===== FULL THREAD DUMP =============== Fri Jun 4 08:22:12 2010 BEA JRockit(R) R27.6.6-28_o-125824-1.6.0_17-20091214-2104-linux-ia32 "Main Thread" id=1 idx=0x4 tid=1 prio=5 alive, in native, waiting -- Waiting for notification on: weblogic/t3/srvr/T3Srvr@0x646ede8[fat lock] at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method) at java/lang/Object.wait(J)V(Native Method) at java/lang/Object.wait(Object.java:485) at weblogic/t3/srvr/T3Srvr.waitForDeath(T3Srvr.java:919) ^-- Lock released while waiting: weblogic/t3/srvr/T3Srvr@0x646ede8[fat lock] at weblogic/t3/srvr/T3Srvr.run(T3Srvr.java:479) at weblogic/Server.main(Server.java:67) at jrockit/vm/RNI.c2java(IIIII)V(Native Method) -- end of trace "(Signal Handler)" id=2 idx=0x8 tid=2 prio=5 alive, in native, daemon Open lock chains ================ Chain 1: "ExecuteThread: '0' for queue: 'weblogic.socket.Muxer'" id=23 idx=0x50 tid=20 waiting for java/lang/String@0x630c588 held by: "ExecuteThread: '1' for queue: 'weblogic.socket.Muxer'" id=24 idx=0x54 tid=21 (active) ===== END OF THREAD DUMP =============== Debug-key '0' pressed Debug-keys enabled Happy Cloud Walking :)

  Read the article

• The First Annual Crappy Code Games

  - by Testas

  SQLBits announced some super-exciting news! A tie-up with our platinum sponsor, Fusion-io. Together we'll be running a series of events called "The Crappy Code Games" where SQL Server developers will compete to write the worst-performing code and win some very cool prizes including:   •        Gold: A hands-on, high performance flying day for two at Ultimate High plus Fusion-io flight jackets•        Silver: One day racing experience at Palmer Sports where you will drive seven different high performance cars•        Bronze: Pure Tech Racing 10 person package at PTR’s F1 racing facility includes FI tees, food and drinks. …plus iPods, Windows Mobile phones, X-box 360s, t-shirts and much more. There will be two qualifying events in Manchester on March 17th and London on March 31st, and the third qualifier as well as the grand finale will be held in the evening of Thursday April 7th at SQLBits. And if that isn’t cool enough, Fusion-io's Chief Scientist Steve Wozniak (yes, that Steve Wozniak, tech industry legend and co-founder of Apple) will be on hand in Brighton to hand out the prizes! If you'd like to take part you'll need to register, and since places are limited we recommend you do so right away. For more details and to register, go to http://www.crappycodegames.com/ The Games: In conjunction with SQL Bits, dbA-thletes (that’s you) will compete  head-to-head in one of three separate qualifying events to be held in Manchester, London and Brighton.  Four separate SQL  rounds make up the evening’s Games, and will challenge you to write code that pushes the boundaries of SQL performance.  The four events are: ?  The High Jump: Generate the highest I/O per second ?  The 100 m dash: Cumulative highest number of I/O’s in 60 seconds ?  The SSIS-athon: Load one billion row fact table in the shortest time ?  The Marathon: Generate the highest MB per second in 60 seconds

  Read the article

• Dart and NetBeans IDE 7.4

  - by Geertjan

  Here's the start of Dart in NetBeans IDE. Basic Dart editing support is done and on saving a Dart file the related JavaScript files are automatically generated. In the context of an HTML5 application in NetBeans IDE, that gives you deep integration with the embedded browser and, even better, Chrome, as well as Chrome Developer Tools. Below, notice that the "Sunflower Spectacular" H1 element is selected (click the image to enlarge it to get a better view), which is therefore highlighted in the live DOM view in the bottom left, as well as in the CSS Styles window in the top right, from where the CSS styles can be edited and from where the related files can be opened in the IDE. Identical features are available for Chrome, as well as on Android and iOS. And if you like that, watch this YouTube movie showing how Chrome Developer Tools integration can fit directly into the workflow below. Anyone want to help get this plugin further? What's needed: Much deeper Dart editing support, i.e., right now only very basic syntax coloring is provided, i.e., an ANTLR lexer is integrated into the NetBeans syntax coloring infrastructure. Parsing, error checking, code completion, and some small code templates are needed. A new panel is needed in the Project Properties dialog on NetBeans HTML5 projects for enabling Dart (i.e., similar to enabling Cordova), at which point the "dart.js" file and other Dart artifacts should be added to the project, so that a Dart project is immediately generated and the application should be immediately deployable. Whenever changes are made to a Dart file, Dart should run in the background to create the Dart artifacts in some hidden way, so that the user doesn't see all the Dart artifacts as is currently the case. Some way of recognizing Dart projects (there's a YAML file as an identifier) and creating NetBeans HTML5 projects from that, i.e., from Dart projects outside the IDE. I think that's all... The official Dart Editor is based on Eclipse and requires a massive download of heaps of Eclipse bundles. Compare that to the NetBeans equivalent, which is a very small "HTML5 and PHP" bundle (60 MB), available here, together with the above small Dart plugin. Plus, when you look at how NetBeans IDE integrates with a bunch of Google-oriented projects, i.e., Chrome, Chrome Developer Tools, and Android (via Cordova), that's a pretty interesting toolbox for anyone using Dart. And bear in mind that ANTLRWorks, Microchip, and heaps of other organizations have built and are building their tools on top of NetBeans!

  Read the article

• Is my computer slow due to lack of swap

  - by Kristian Jensen

  A few months ago, I installed Ubuntu 12.04 alongside with Windows 7 on my Asus EEE-PC 1015bx. It has a tendency of freezing and when trying to investigate I found that a swap partition of only 256 MB had been created. The Asus EEE-PC 1015bx is born with 1 GByte RAM only and it is not possible to add further or exchange the existing 1 GByte with a larger card. When looking at the system monitor, it looks like all swap is being utilized along with 70-75% of the RAM, even with very few applications running. Can the lack of much swap space be the reason for my computer running slowly and at times freezing? How can I add a swap partition? Or should I add a swap file instead? At the moment, I see two partitions when viewing the system monitor: one 28.6 GByte ext4 partition which must be the one containing Ubuntu and one 100 GByte fuseblk partition which I assume is the one holding Windows. It shows that I have 18.6 GByte free space on the ext4 partition. Can I "take a bite" from the ext4 partition and convert this into a swap partition? I was thinking something like 3 GBytes for swap considering my limited RAM. I hope that someone can guide me through. Thank you. 20th Oct 2012 - Further details Thank you for below answer which I find very useful. I am certainly considering switching to one of your suggested shells as I can see from the Internet that many have posted that these require much fewer resources than ubuntu. It seems to me that lubuntu is the perfect match for my very limited computer. I will have to wait a few days, though, as I am presently limited by a very slow and restricted Internet connection via satellite. But will lubuntu install as simply another shell replacing unity or will it replace ubuntu all together? Will the software that I have installed under ubuntu still be accessible in lubuntu? And can I return to ubuntu if required? Regarding the actual question of swap: When I run gparted, it shows me that there is one ntfs partition of 100 GBytes from where it boots and the before mentioned ext4 partition of 28.6 GBytes is not mentioned. Could it be that my ubuntu installation resides inside this 100 GBytes ntfs partiotion? And if so, can I take a bite of this for my swap partition? Realising that gparted is shown in Danish, I hope that you can make out what I mean. System monitoring shows below details: Once again I sincerely hope that you can help. Thank you.

  Read the article

• Ubuntu 12.04 LTS installation problem

  - by Zxy

  I am trying to install Ubuntu 12.04 LTS on my PC using WUBI. However, I keep getting this error: An error occured: *Error executing command >>command=C:\\System32\bcdedit.exe /set {2708afc0-9ffa-11e1-bc51-d167219ffa25} device partition=E: >>retval=1 >>stderr=An error has occured setting the element data. The request is not supported. >>stdout= For more information, please see the logfile:* Logfile: 06-11 10:57 DEBUG TaskList: ## Finished choose_disk_sizes 06-11 10:57 DEBUG TaskList: ## Running expand_diskimage... 06-11 10:59 DEBUG TaskList: ## Finished expand_diskimage 06-11 10:59 DEBUG TaskList: ## Running create_swap_diskimage... 06-11 10:59 DEBUG TaskList: ## Finished create_swap_diskimage 06-11 10:59 DEBUG TaskList: ## Running modify_bootloader... 06-11 10:59 DEBUG TaskList: New task modify_bcd 06-11 10:59 DEBUG TaskList: ### Running modify_bcd... 06-11 10:59 DEBUG WindowsBackend: modify_bcd Drive(C: hd 51255.1171875 mb free ntfs) 06-11 10:59 ERROR TaskList: Error executing command >>command=C:\Windows\System32\bcdedit.exe /set {2708afc0-9ffa-11e1-bc51-d167219ffa25} device partition=E: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= Traceback (most recent call last): File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\win32\backend.py", line 697, in modify_bcd File "\lib\wubi\backends\common\utils.py", line 66, in run_command Exception: Error executing command >>command=C:\Windows\System32\bcdedit.exe /set {2708afc0-9ffa-11e1-bc51-d167219ffa25} device partition=E: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= 06-11 10:59 DEBUG TaskList: # Cancelling tasklist 06-11 10:59 DEBUG TaskList: New task modify_bcd 06-11 10:59 ERROR root: Error executing command >>command=C:\Windows\System32\bcdedit.exe /set {2708afc0-9ffa-11e1-bc51-d167219ffa25} device partition=E: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= Traceback (most recent call last): File "\lib\wubi\application.py", line 58, in run File "\lib\wubi\application.py", line 132, in select_task File "\lib\wubi\application.py", line 158, in run_installer File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\win32\backend.py", line 697, in modify_bcd File "\lib\wubi\backends\common\utils.py", line 66, in run_command Exception: Error executing command >>command=C:\Windows\System32\bcdedit.exe /set {2708afc0-9ffa-11e1-bc51-d167219ffa25} device partition=E: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= 06-11 10:59 DEBUG TaskList: New task modify_bcd 06-11 10:59 DEBUG TaskList: New task modify_bcd 06-11 10:59 DEBUG TaskList: ## Finished modify_bootloader 06-11 10:59 DEBUG TaskList: # Finished tasklist*

  Read the article

• Problem with apt-get [install, purge, autoremove, upgrade]

  - by Ark

  I am trying to install openvpn using apt-get, but I get an error during the process [As far as I understand the issue is with unattended-updates, which I could not upgrade due to apt-get porblem :/]. I cannot upgrade, install, autoremove or purge anything else [which I need to do since /boot is full. For upgrading I did update before trying].... Trace [on sudo apt-get autoremove]: 0 upgraded, 0 newly installed, 79 to remove and 421 not upgraded. 35 not fully installed or removed. Need to get 24.1 kB of archives. After this operation, 140 MB disk space will be freed. Do you want to continue [Y/n]? y Get:1 http://us.archive.ubuntu.com/ubuntu/ oneiric/main unattended-upgrades all 0.73ubuntu1 [24.1 kB] Fetched 24.1 kB in 0s (31.2 kB/s) Preconfiguring packages ... (Reading database ... 287206 files and directories currently installed.) Removing flashplugin-downloader:i386 ... Removing libasound2-plugins:i386 ... Removing libpulse0:i386 ... Removing libsndfile1:i386 ... Removing libvorbisenc2:i386 ... Removing libvorbis0a:i386 ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place (Reading database ... 287174 files and directories currently installed.) Preparing to replace unattended-upgrades 0.73ubuntu1 (using .../unattended-upgrades_0.73ubuntu1_all.deb) ... Checking for running unattended-upgrades: Traceback (most recent call last): File "/usr/share/unattended-upgrades/unattended-upgrade-shutdown", line 27, in <module> import apt_pkg ImportError: No module named apt_pkg invoke-rc.d: initscript unattended-upgrades, action "stop" failed. dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Checking for running unattended-upgrades: Traceback (most recent call last): File "/usr/share/unattended-upgrades/unattended-upgrade-shutdown", line 27, in <module> import apt_pkg ImportError: No module named apt_pkg invoke-rc.d: initscript unattended-upgrades, action "stop" failed. dpkg: error processing /var/cache/apt/archives/unattended-upgrades_0.73ubuntu1_all.deb (--unpack): subprocess new pre-removal script returned error exit status 1 update-rc.d: warning: unattended-upgrades start runlevel arguments (2 3 4 5) do not match LSB Default-Start values (none) update-rc.d: warning: unattended-upgrades stop runlevel arguments (0 1 6) do not match LSB Default-Stop values (0 6) Checking for running unattended-upgrades: Traceback (most recent call last): File "/usr/share/unattended-upgrades/unattended-upgrade-shutdown", line 27, in <module> import apt_pkg ImportError: No module named apt_pkg invoke-rc.d: initscript unattended-upgrades, action "start" failed. dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/unattended-upgrades_0.73ubuntu1_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Maybe I missed something basic, but I would appreciate pointers on solving the issue. Thanks

  Read the article

• apt-get broken + dependencies issue + many software uninstalled

  - by vnc786

  OS=ubuntu 12.04 64bit 3.2.0-29-generic what i did? apt-get purge libre* which i thought will remove LO 3.5 but, which was a big mistake after couple of moments, i realise that its is removing all other software so i did cltl-c which stopped the apt process i restarted my system after that i found that following software were missing apt-get,evince(pdf), cheese etc..here is full list http://pastebin.com/CWHrw10y i managed to install APT deb file through dpkg but now i am not able to do any installation so i just removed /var/lib/dpkg/status and created new but that didnt help apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: apt-utils coreutils debconf debconf-i18n dpkg libacl1 libapt-inst1.4 libapt-pkg4.12 libattr1 libbz2-1.0 libdb5.1 libgcc1 liblocale-gettext-perl liblzma5 libselinux1 libstdc++6 libtext-charwidth-perl libtext-iconv-perl libtext-wrapi18n-perl perl-base tar tzdata xz-utils zlib1g Suggested packages: debconf-doc debconf-utils whiptail dialog gnome-utils libterm-readline-gnu-perl libgtk2-perl libnet-ldap-perl libqtgui4-perl libqtcore4-perl apt bzip2 ncompress xz-lzma The following NEW packages will be installed: apt-utils coreutils debconf debconf-i18n dpkg libacl1 libapt-inst1.4 libapt-pkg4.12 libattr1 libbz2-1.0 libdb5.1 libgcc1 liblocale-gettext-perl liblzma5 libselinux1 libstdc++6 libtext-charwidth-perl libtext-iconv-perl libtext-wrapi18n-perl perl-base tar tzdata xz-utils zlib1g 0 upgraded, 24 newly installed, 0 to remove and 0 not upgraded. 2 not fully installed or removed. Need to get 0 B/9,246 kB of archives. After this operation, 29.9 MB of additional disk space will be used. Do you want to continue [Y/n]? y E: Cannot get debconf version. Is debconf installed? debconf: apt-extracttemplates failed: No such file or directory dpkg: regarding .../libgcc1_1%3a4.6.3-1ubuntu5_amd64.deb containing libgcc1, pre-dependency problem: libgcc1 pre-depends on multiarch-support multiarch-support is unpacked, but has never been configured. dpkg: error processing /var/cache/apt/archives/libgcc1_1%3a4.6.3-1ubuntu5_amd64.deb (--unpack): pre-dependency problem - not installing libgcc1 No apport report written because MaxReports is reached already Errors were encountered while processing: /var/cache/apt/archives/libgcc1_1%3a4.6.3-1ubuntu5_amd64.deb E: Internal Error, No file name for libc6 W: Could not perform immediate configuration on 'multiarch-support:amd64'. Please see man 5 apt.conf under APT::Immediate-Configure for details. (2) E: Sub-process /usr/bin/dpkg returned an error code (1) # apt-get -u dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: libc6 : Depends: libgcc1 but it is not installed Depends: tzdata but it is not installed E: Unmet dependencies. Try using -f. i have tried below link Unable to install due to debconf problem How do I resolve unmet dependencies? but no help... thanks

  Read the article

• RealTek RTL8188CE WiFi adapter doesn't connect reliably

  - by ken.ganong

  I recently bought a new system76 laptop which came pre-installed with Ubuntu 11.10. I've been having trouble with my wireless connectivity. It seems that my connection with my wireless network keeps going in and out. It is not my network--I have seen the same problem on multiple WiFi networks and at different distances and reported link qualities. OS version: Ubuntu 11.10 oneiric kernel version: 3.0.0-14-generic lspci: lspci -nnk | grep -iA2 net 04:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:9196] Kernel driver in use: rtl8192ce -- 05:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) Subsystem: CLEVO/KAPOK Computer Device [1558:2500] Kernel driver in use: jme iwconfig: iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"peppermintpatty" Mode:Managed Frequency:2.462 GHz Access Point: 98:FC:11:6C:E0:22 Bit Rate=72.2 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Power Management:off Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:1103 Missed beacon:0 lshw: sudo lshw -class network *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 00:1c:7b:a1:95:04 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.0.0-14-generic firmware=N/A ip=192.168.1.106 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:18 ioport:e000(size=256) memory:f7d00000-f7d03fff *-network description: Ethernet interface product: JMC250 PCI Express Gigabit Ethernet Controller vendor: JMicron Technology Corp. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 00:90:f5:c0:42:b3 size: 10Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:56 memory:f7c20000-f7c23fff ioport:d100(size=128) ioport:d000(size=256) memory:f7c10000-f7c1ffff memory:f7c00000-f7c0ffff Any help would be appreciated. The last time I've dealt with wireless issues, the most given solution was NDIS wrapper and I seem sorely out-of-date.

  Read the article

• how to start LXDE session automatically after tightvncserver starts to make me able see desktop when connecting to the host via vncclient?

  - by Oleksandr Dudchenko

  I have system which is equipped with Intel Celeron processor 1.1 GHz s370 with 384 Mb of RAM on Intel d815egew motherboard which supports wake-on-lan function. I want to use such a PC for Internet sharing to the local network. Also this PC is a DHCP+DNS server as well as router/gateway. Based on above I decided to install Lubuntu as it is lightweight system. I installed Lubuntu 10.04.4 LTS from alternate ISO. System has no auto login. System boots and has acceptable performance. Host PC has onboard 4 network adapters: eth0 – ethernet controller which is used for Local Network connections. Has static address 10.0.0.1 eth1 – ethernet controller which is not used and not configured so far, I plan to connect printer here later on. eth2 - ethernet controller which is used to connect to Internet, which we plan to share for the local network wlan0 – wireless controller, it is used in role of access poit for local Network and has address 10.0.0.2 We want to control our gateway remotely. So, we need to be able to power it on remotely. To allow this I’ve done the following things: $ cd /etc/init.d/ made a new file with command $ sudo vim wakeonlanconfig Wrote the following lines to the newly created file, saved and closed it #!/bin/bash ethtool -s eth0 wol g ethtool -s eth2 wol g exit Made the abovementioned file executable $ sudo chmod a+x wakeonlanconfig Then included it into autostart sequence during boot. $ sudo update-rc.d -f wakeonlanconfig defaults after system reboot we will be able to poweron system remotely. Than we need to have a possibility to connect remotely to the host via SSH and VNC. So, I installed following packets with the following commands: $ sudo apt-get update $ sudo apt-get install openssh-server tightvncserver Add ssh daemon into autostart sequence during boot. $ sudo update-rc.d -f ssh defaults Power off the host PC $ sudo halt Then I went to remote place, send magic paket and powered the Host up. System started... And I connected to the host via Putty from remote system under Windows. Than logged in and run the command to start vnc server. $ tightvncserver -geometry 800x600 -depth 16 :2 VNC server successfully started and I got message like follows. New 'X' desktop is gateway:2 Starting applications specified in /home/dolv/.vnc/xstartup Log file is /home/dolv/.vnc/gateway:2.log Using UltraVNC Viewer programm under windows I connected to the host's vnc server, enterd the password and.... sow only mouse cursor in form of cross on a grey background of 800x600 dots, no desktop. Here is my .vnc/xstartup file #!/bin/sh xrdb $HOME/.Xresources xsetroot -solid grey #x-terminal-emulator -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & #x-window-manager & # Fix to make GNOME work export XKL_XMODMAP_DISABLE=1 /etc/X11/Xsession The Question: What I have to change and where to make LXDE session start automatically after tightvncserver starts?

  Read the article

• The Windows 8 and Ubuntu 12.04 Dual Boot NIghtmare

  - by Steve

  I have done some research as to how to go about this dual-boot, and I am close, but I need some guidance with booting into Windows 8 (Ubuntu is installed). I have a Lenovo Ideapad y510p. I will go over what I have done to dual-boot this laptop, with windows 8 pre-installed, with Ubuntu 12.04: I followed every instruction to the letter for the 97-vote response here, and everything worked fine up until after the repair boot section: Installing on a Pre-Installed Windows 8 System (UEFI Supported) I ran into the following error upon restarting after the repair boot section: error: invalid arch independent elf magic. This error (a grub issue) disabled me from booting into Ubuntu :( After a little googling, I followed the instructions in the reactivating grub 2 section to resolve the error: http://kb.acronis.com/content/1686 I found a possible solution to fixing the Windows 8 boot issue, and tried it: http://webcache.googleusercontent.com/search?q=cache:i9JMyXzzRpYJ:askubuntu.com/questions/279275/dual-boot-problem-windows-8-ubuntu-12-04+&cd=1&hl=en&ct=clnk&gl=us&client=ubuntu I thought the above solution worked, but when I attempt to boot into Windows 8, I get the following missing file error: File: \Boot\BCD Status: 0xc000000e Info: The Boot Configuration Data for your PC is missing or contains errors. Here is some other information that may be useful: I have 3 partitions devoted to Ubuntu. The first, sda8, has a flag bios_grub (1049 kb). The second, sda9, is where everything else is (96.6 GB). The last, sda10, is for swap (8299 MB). My question is: How do I fix the boot configuration for Windows 8? Any help would be greatly appreciated :) Update 1: When I attempt to boot into UEFI mode, I get the following error: invalid arch independent elf magic (the same error I saw in step 2). Update 2: A useful link here I found: Dual booting Ubuntu 12.04: UEFI and Legacy So, this is my 4th time installing Ubuntu on the laptop, and it looks like I need to install it in UEFI mode. Should I scrap it all again, and reinstall? Or is there ANY way of salvaging my installation? At this point, I can't even boot into Windows (although I have an installation cd to fix the windows boot issue, that would ultimately screw over ubuntu). Update 3: After doing a little more browsing around, I found a cool way around this messy grub stuff, using rEFInd. Rod Smith's post here saved me! Installing ubuntu 12.04.02 in uefi mode Now, I am able to dual-boot Windows 8 and Ubuntu and boot into both operating systems :) I have another issue (relating to the boot configuration in the bios) that I will post as a separate question :)

  Read the article

• How do I get wireless working on a Dell Inspiron 510m?

  - by user17449

  Why WiFi don't work in my Dell Inspiron 510m with Ubuntu 10.04? Is that usefull? inspiron@Inspiron:~$ rfkill list all inspiron@Inspiron:~$ sudo lshw -C network [sudo] password for inspiron: *-network:0 DISABLED description: Wireless interface product: PRO/Wireless LAN 2100 3B Mini PCI Adapter vendor: Intel Corporation physical id: 3 bus info: pci@0000:01:03.0 logical name: eth1 version: 04 serial: 00:0c:f1:5b:5d:40 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ipw2100 driverversion=git-1.2.2 firmware=712.0.3:3:00000001 latency=32 link=no maxlatency=34 mingnt=2 multicast=yes wireless=unassociated resources: irq:5 memory:fcffe000-fcffefff *-network:1 description: Ethernet interface product: 82801DB PRO/100 VE (MOB) Ethernet Controller vendor: Intel Corporation physical id: 8 bus info: pci@0000:01:08.0 logical name: eth0 version: 81 serial: 00:11:43:41:d8:b8 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half firmware=N/A ip=192.168.0.2 latency=32 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10MB/s resources: irq:11 memory:fcffd000-fcffdfff ioport:ecc0(size=64) inspiron@Inspiron:~$ iwconfig wlan0 wlan0 No such device inspiron@Inspiron:~$ ifconfig -a eth0 Link encap:Ethernet Endereço de HW 00:11:43:41:d8:b8 inet end.: 192.168.0.2 Bcast:192.168.0.255 Masc:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet Endereço de HW 00:0c:f1:5b:5d:40 BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) IRQ:5 Endereço de E/S:0xe000 Memória:fcffe000-fcffefff lo Link encap:Loopback Local inet end.: 127.0.0.1 Masc:255.0.0.0 endereço inet6: ::1/128 Escopo:Máquina UP LOOPBACK RUNNING MTU:16436 Métrica:1 pacotes RX:628 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:628 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:0 RX bytes:50104 (50.1 KB) TX bytes:50104 (50.1 KB) inspiron@Inspiron:~$ nm-tool NetworkManager Tool State: connected - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: ipw2100 State: unavailable Default: no HW Address: 00:0C:F1:5B:5D:40 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: e100 State: unmanaged Default: no HW Address: 00:11:43:41:D8:B8 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: off inspiron@Inspiron:~$

  Read the article

• Wireless acting weird ubuntu 12.04 LTS

  - by Philip Yeldhos

  I'm kinda new here, so please bear with me. My wireless driver is acting very weird. It shows my router's name, but when it is connecting (after entering the correct password), the icon on the tray is like, refreshing every once in a second, while showing the animation that it is connecting. And after a few seconds, error message come up saying that wireless network is disconnected. I installed the drive through "additional drivers". What info do you need? Somebody please help. philip@philip-HP-Mini-110-3100:~$ sudo iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.472 GHz Access Point: Not-Associated Bit Rate:72 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:11 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. here's what lspci -v gave me: 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Hewlett-Packard Company Device 1483 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at 52000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 <?> Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-82-ff-ff-3f-e0-2a Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac okay, i removed the driver additional drivers gave me. now, this is what has happened: lsmod gave me: philip@philip-HP-Mini-110-3100:~$ lsmod | grep brc brcmsmac 540875 0 mac80211 436455 1 brcmsmac brcmutil 14675 1 brcmsmac cfg80211 178679 2 brcmsmac,mac80211 crc8 12781 1 brcmsmac cordic 12487 1 brcmsmac and iwconfig gave me: philip@philip-HP-Mini-110-3100:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. and lspci -v gave me: 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Hewlett-Packard Company Device 1483 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at 52000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

  Read the article

• Getting up and started with the Windows Phone Developer Tools 7.1 Beta 2

  - by mbcrump

  Windows Phone Developer Tools 7.1 Beta 2 was released on 6/29/2011. Are you ready for it? If not then let my guide help you get your system prepared and go through a few new features. Download links: Web Installer of Windows Phone 7.1 Beta 2 SDK ISO Image of Windows Phone 7.1 Beta 2 SDK - (723 MB) To get started you are going to need to remove the previous version of your Windows Phone Developer Tools 7.1 Beta 1.   This kicks off the process of uninstalling the Beta.   Once it is uninstalled then you are going to want to grab the bits from: http://www.microsoft.com/download/en/details.aspx?id=26648. The only thing your interested in here is the vm_web2.exe.   Make sure before you start that Zune is not running or you will get this error message like this one and have to restart from scratch. Now just go through your normal Install Screens. It should be installed and ready to go: A couple of things to note: 1) When creating a new phone application you now have several new templates to choose from as shown below. I welcome this addition because I’m a firm believer that we need more templates in order to get more people started. 2) Once you select an application template you can now pick which version of the Windows Phone platform that you wish to target: 3) If you created a WP7 7.1 Beta 1 project that it will still work properly in WP7 7.1 Beta 2. 4) You now have access to the search app icon. Once pressed then you will see something like this: 5) Under Settings –> Applications. You now have background tasks. 6) You will notice that the Web Browser looks a little different with the URL now located at the bottom of the screen and completely removing the “add”, “favorites” and “tabs” icon. Those icons are now moved to the menu bar.   That is it for my “Getting up and going with the Windows Phone Developer Tools 7.1 Beta 2”. I hope you enjoyed it and please feel free to subscribe to my feed or follow me on Twitter.   Subscribe to my feed

  Read the article

• SQL – What ACID stands in the Database? – Contest to Win 24 Amazon Gift Cards and Joes 2 Pros 2012 Kit

  - by Pinal Dave

  We love puzzles. One of the brain’s main task is to solve puzzles. Sometime puzzles are very complicated (e.g Solving Rubik Cube or Sodoku)  and sometimes the puzzles are very simple (multiplying 4 by 8 or finding the shortest route while driving). It is always to solve puzzle and it creates an experience which humans are not able to forget easily. The best puzzles are the one where one has to do multiple things to reach to the final goal. Let us do something similar today. We will have a contest where you can participate and win something interesting. Contest This contest have two parts. Question 1: What ACID stands in the Database? This question seems very easy but here is the twist. Your answer should explain minimum one of the properties of the ACID in detail. If you wish you can explain all the four properties of the ACID but to qualify you need to explain minimum of the one properties. Question 2: What is the size of the installation file of NuoDB for any specific platform. You can answer this question following format – NuoDB installation file is of size __ MB for ___ Platform. Click on the Download the Link and download your installation file for NuoDB. You can post figure out the file size from the properties of the file. We have exciting content prizes for the winners. Prizes 1) 24 Amazon Gift Cards of USD 10 for next 24 hours. One card at every hour. (Open anywhere in the world) 2) One grand winner will get Joes 2 Pros SQL Server 2012 Training Kit worth USD 249. (Open where Amazon ship books). Amazon | 1 | 2 | 3 | 4 | 5  Rules The contest will be open till July 21, 2013. All the valid comments will be hidden till the result is announced. The winners will be announced on July 24, 2013. Hint: Download NuoDB  Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Puzzle, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Can't access local network when connect to pppoe

  - by shantanu

  I am using DSL(PPPOE) connection in ubuntu. It has two part (I am not sure), when I just connect the cable, system automatically get an IP address started with 172.x.x.x(DHCP). When I connect using username/password (PPPOE) I get another IP started with 10.x.x.x and can access internet but can't access some local IP (in my LAN), which are some FTP, media server provided by my ISP. I complained about that to my ISP but they reply Windows is working It's true, Windows 7 is working fine with this settings. I can access internet and local server at the same time. Also I use a WIFI router (TP-link TL-WR340G/TL-WR340GD) which result the same problem. So when I connect cable directly to system and use Windows 7 than everything is fine. Otherwise problem. Similar problem discussed here. Edit before connect. route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.100.0.1 0.0.0.0 UG 0 0 0 eth0 172.100.0.0 0.0.0.0 255.255.0.0 U 1 0 0 eth0 after connect. Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.12.44.91 0.0.0.0 UG 0 0 0 ppp0 10.12.44.91 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 ifconfig after connect eth0 Link encap:Ethernet HWaddr 74:d0:2b:d5:b3:6c inet6 addr: fe80::76d0:2bff:fed5:b36c/64 Scope:Link inet6 addr: 2002:ac64:154:c:76d0:2bff:fed5:b36c/64 Scope:Global inet6 addr: fec0::c:76d0:2bff:fed5:b36c/64 Scope:Site UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:26582 errors:0 dropped:18 overruns:0 frame:0 TX packets:2340 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2542063 (2.5 MB) TX bytes:244938 (244.9 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4118 errors:0 dropped:0 overruns:0 frame:0 TX packets:4118 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:336759 (336.7 KB) TX bytes:336759 (336.7 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:10.12.44.95 P-t-P:10.12.44.91 Mask:255.255.255.255 inet6 addr: fe80::a536:c7ae:e079:d88d/10 Scope:Link UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:689 errors:0 dropped:0 overruns:0 frame:0 TX packets:744 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:385746 (385.7 KB) TX bytes:75296 (75.2 KB) I used network manager to create network(DSL connection)

  Read the article

• Squid: caching *.swf with variables

  - by stfn

  I'd recently upgraded my Ubuntu 11.10 x64 server to 12.04. In this process Squid was updated from 2.7 to 3.1. Squid 3.1 has many different options witch broke my setup. So I completely removed squid 2.7 and 3.1 and started from scratch. Everything is now working as before except for 1 thing: caching of .swf files with ?/variables. Squid 3 sees a ? as dynamic content and does not cache it. For example, Squid 2.7 was caching the .swf file at http://ninjakiwi.com/Games/Tower-Defense/Play/Bloons-Tower-Defense-5.html and 3.1 is not. <object id="mov" name="movn" classid="clsid:D27CDB6E-AE6D-11cf-96B8-444553540000" width="800" height="620"> <param name="movie" value="http://www.ninjakiwifiles.com/Games/gameswfs/btd5.swf?v=160512-2"> <param name="allowscriptaccess" value="always"> <param name="bgcolor" value="#000000"> <param name="flashvars" value="file=http://www.ninjakiwifiles.com/Games/gameswfs/btd5-dat.swf?v=280512"> <p>Get Flash play Ninja Kiwi games.</p> </object> It is because of the "?v=160512-2" and "?v=280512" part. This line should be responsible for that: refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 But disabling it still doesn't cache the .swf files. How do I configure Squid 3.1 to cache those files? My current config is: acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT acl localnet src 192.168.2.0-192.168.2.255 acl localnet src 192.168.3.0-192.168.3.255 http_access allow manager localhost http_access deny manager http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow localhost http_access allow localnet http_access deny all http_port 3128 cache_dir ufs /var/spool/squid 10240 16 256 maximum_object_size 100 MB coredump_dir /var/spool/squid3 refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i \.(gif|png|jpg|jpeg|ico)$ 10080 90% 43200 override-expire ignore-no-cache ignore-no-store ignore-private refresh_pattern -i \.(iso|avi|wav|mp3|mp4|mpeg|swf|flv|x-flv)$ 43200 90% 432000 override-expire ignore-no-cache ignore-no-store ignore-private refresh_pattern -i \.(deb|rpm|exe|zip|tar|tgz|ram|rar|bin|ppt|doc|tiff)$ 10080 90% 43200 override-expire ignore-no-cache ignore-no-store ignore-private refresh_pattern -i \.index.(html|htm)$ 0 40% 10080 refresh_pattern -i \.(html|htm|css|js)$ 1440 40% 40320 refresh_pattern Packages\.bz2$ 0 20% 4320 refresh-ims refresh_pattern Sources\.bz2$ 0 20% 4320 refresh-ims refresh_pattern Release\.gpg$ 0 20% 4320 refresh-ims refresh_pattern Release$ 0 20% 4320 refresh-ims refresh_pattern . 0 40% 40320 cache_effective_user proxy cache_effective_group proxy

  Read the article

• Intel Centrino Wireless N 1000 doesn't work on a Lenovo Z560

  - by Timetraveler

  I upgraded my Ubuntu 11.04 to 11.10 and my Wifi has stopped working. I have a Lenovo Z560 that has Intel centrino wireless-N 1000. I have searched various threads having similar problems for a solution and have no success. The wlan0 is not even showing up in rfkill. Please help me find a solution. I am giving below the output of various debug commands. Thanks in advance. DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" ----##uname -a Linux gurucharapathy-laptop 3.0.0-17-generic-pae #30-Ubuntu SMP Thu Mar 8 17:53:35 UTC 2012 i686 i686 i386 GNU/Linux ----##lspci -nnk | grep -iA2 net 05:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0084] Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN [8086:1315] Kernel modules: iwlagn 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 ----##iwconfig lo no wireless extensions. eth0 no wireless extensions. ----##iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. ----##rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no ----##lsmod Module Size Used by rfcomm 38408 8 bnep 17923 2 parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 snd_hda_codec_hdmi 31426 1 snd_hda_codec_conexant 52460 1 uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 28358 2 snd_hda_codec 91859 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec joydev 17393 0 snd_pcm 80435 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 i915 509554 9 drm_kms_helper 32889 1 i915 snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28932 2 snd_pcm,snd_seq drm 196290 5 i915,drm_kms_helper snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq mei 36466 0 mac80211 393421 0 snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 13575 0 intel_ips 17753 0 btusb 18160 2 i2c_algo_bit 13199 1 i915 soundcore 12600 1 snd bluetooth 148839 23 rfcomm,bnep,btusb cfg80211 172427 1 mac80211 psmouse 63474 0 serio_raw 12990 0 snd_page_alloc 14108 2 snd_hda_intel,snd_pcm sparse_keymap 13658 1 ideapad_laptop wmi 18744 0 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 2 libahci 25761 1 ahci r8169 47200 0 ----##nm-tool NetworkManager Tool State: asleep Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: r8169 State: unmanaged Default: no HW Address: 88:AE:1D:DE:5F:9C Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on ----##lshw -C network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d6400000-d6401fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:de:5f:9c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.0.100 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff

  Read the article

• Broken package after update: linux-headers, error brokencount >0

  - by escozul

  Ubuntu 12.04. After an update, I get a red warning icon in the system tray, warning about an error: broken count 0 Opening Update manager, I see that the broken package is linux-headers-3.2.0-33-generic-pae (new install) Specificaly I have my ubuntu on an AspireOne with 8gb internal storage. I tried apt-get clean as suggested in another question on this site, and tried reinstalling the package in Synaptic. I have tried to reboot but to no avail. I have also tried apt-get install --fix-broken and I get the following: sudo apt-get install --fix-broken [sudo] password for elina: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: linux-headers-3.2.0-33-generic-pae The following NEW packages will be installed: linux-headers-3.2.0-33-generic-pae 0 upgraded, 1 newly installed, 0 to remove and 38 not upgraded. 1 not fully installed or removed. Need to get 0 B/977 kB of archives. After this operation 11,3 MB of additional disk space will be used. Do you want to continue [Y/n]; y (Reading database ... 437051 files and directories currently installed.) Unpacking linux-headers-3.2.0-33-generic-pae (from .../linux-headers-3.2.0-33-generic-pae_3.2.0-33.52_i386.deb) ... dpkg: error processing /var/cache/apt/archives/linux-headers-3.2.0-33-generic-pae_3.2.0-33.52_i386.deb (--unpack): unable to create `/usr/src/linux-headers-3.2.0-33-generic-pae/include/config/usb/gspca/sonixb.h.dpkg-new' (while processing `./usr/src/linux-headers-3.2.0-33-generic-pae/include/config/usb/gspca/sonixb.h'): No space left on device No apport report written because the error message indicates a disk full error dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/linux-headers-3.2.0-33-generic-pae_3.2.0-33.52_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) I've tried all suggestions I could find: sudo apt-get clean sudo apt-get autoclean sudo apt-get autoremove sudo apt-get update sudo apt-get upgrade sudo apt-get -f install sudo apt-get install --fix-broken Then I saw that on the error there was a mention about free space. So I did a df -h and the result was: Filesystem Size Used Avail Use% Mounted on /dev/sda1 7,0G 5,5G 1,1G 84% / udev 235M 4,0K 235M 1% /dev tmpfs 97M 816K 96M 1% /run none 5,0M 0 5,0M 0% /run/lock none 242M 352K 242M 1% /run/shm I see that on my root folder I have 1.1Gb free. The broken package is linux-headers-3.2.0-33-generic-pae_3.2.0-33.52_i386.deb which only takes up 11.3Mb on my hard drive. I'm soooo lost. I really hope there is something I'm missing here. I don't want to go about reformatting this bucket. It's really not worth the time. Any help for fixing this would be hot.

  Read the article

• WiFi connected to router, but no internet connection

  - by Quetzacotl

  I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

  Read the article

• Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

  - by Donal

  I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >