Search Results

Search found 21814 results on 873 pages for 'morgan may'.

Page 73/873 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

  • IP tables blocking access to most hosts but some accesses being logged

    - by epo
    What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

    Read the article

  • how can i move ext3 partition to the beginning of drive without losing data?

    - by Felipe Alvarez
    I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

    Read the article

  • ssh - "Connection closed by xxx.xxx.xxx.xxx" - using password

    - by Michael B
    I attempted to create an new user account that I wish to use to log in using ssh. I did this (in CentOs): /usr/sbin/adduser -d /home/testaccount -s /bin/bash user passwd testaccount This is the error I receive when trying to log in via ssh: ~/.ssh$ ssh -v [email protected] OpenSSH_5.1p1 Debian-5ubuntu1, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to xxx.xxx.xxx [xxx.xxx.xxx.xxx] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/identity type -1 debug1: identity file /home/user/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: identity file /home/user/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.3 debug1: match: OpenSSH_4.3 pat OpenSSH_4* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'xxx.xxx.xxx.xxx' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:8 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering public key: /home/user/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Trying private key: /home/user/.ssh/identity debug1: Trying private key: /home/user/.ssh/id_dsa debug1: Next authentication method: password testaccount@xxx's password: Connection closed by xxx.xxx.xxx.xxx The "connection closed" message appeared immediately after entering the password (if I enter the wrong password it waits and then prompts for another password) I am able to log in from the same computer using other accounts that had been setup previously. When logged into the remote machine I am able to do 'su testaccount' Thanks for your time.

    Read the article

  • Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

    - by Ron Whites
    Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

    Read the article

  • Linux: Send mail to external mail box from a server with that user's hostname

    - by dtbarne
    I've got sendmail running on a linux box. Let's say the hostname of the box is bar.com. If I run the following command, I don't receive the email (which is hosted with a third party), presumably due to the hostname pointing to the local machine. echo "Test Body" | mail -s "Test Subject" [email protected] Is there any way to get this to work so that I can receive emails at my third party email address even though it has the same hostname? Do I have to change the hostname of this server (not preferred)? It may be worth noting that I created a user "foo" on my machine and noticed that the mailbox for that account is empty. I noticed these log entries, which may or may not be relevant: Jun 28 01:09:48 bar sendmail[14338]: p5S59min014338: from=apache, size=80, class=0, nrcpts=1, msgid=<[email protected]>, relay=apache@localhost Jun 28 01:09:48 bar sendmail[14339]: p5S59mIA014339: from=<[email protected]>, size=293, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA, relay=localhost.localdomain [127.0.$ Jun 28 01:09:48 bar sendmail[14338]: p5S59min014338: [email protected], ctladdr=apache (48/48), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30080, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (p5S59mIA$ Jun 28 01:09:48 bar sendmail[14340]: p5S59mIA014339: to=<[email protected]>, ctladdr=<[email protected]> (48/48), delay=00:00:00, xdelay=00:00:00, mailer=local, pri=30495, dsn=2.0.0, stat=Sent

    Read the article

  • Nginx Ubuntu Postfix Config - Can't connect to incoming IMAP server 'server not responding' but can send mail via outgoing using same details?

    - by daveaspinall
    I'm pretty to new server admin and especially nginx but seem to be getting ok fine apart from accessing my mail via my iPhone? I've changed my domain to 'domain.com' The thing is I can send mail via my outgoing IMAP server but can't connect to the incoming one? I just get the message "the mail server at mail.domain.com is not responding" /etc/postfix/main.cf alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix home_mailbox = Maildir/ inet_interfaces = all inet_protocols = all mailbox_command = mailbox_size_limit = 0 mydestination = domain.com, mail.domain.com, localhost.com, , localhost, localhost.localdomain mydomain = domain.com myhostname = mail.domain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname recipient_delimiter = + relayhost = smtp_tls_note_starttls_offer = yes smtp_tls_security_level = may smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = smtpd_sasl_security_options = noanonymous smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_auth_only = no smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_security_level = may smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom telnet localhost 25 ehlo locahost 250-mail.domain.com 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-AUTH LOGIN PLAIN 250-AUTH=LOGIN PLAIN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN Using the following details to connect: username password hostname: mail.domain.com port: 25 iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I also sent mail to the server as a test and got this missage if it helps? Technical details of temporary failure: [mail.domain.com. (10): Connection refused] I also looked in /var/log/mail.log and it has multiple entries of: postfix/smtpd[12239]: connect from 5acefc9a.bb.sky.com[90.206.252.xxx] Mar 23 06:47:09 new-domain postfix/smtpd[12239]: lost connection after CONNECT from 5acefc9a.bb.sky.com[90.206.252.154] Notice new-domain which is incorrect but the server hostname and hostname in the configs are correct? I recently moves servers and the host has set the primary domain on the service as new-domain.com so this may be the issue? Like I said, it works to connect to outgoing server, but incoming gets the not responding error? Any idea would be much appreciated!

    Read the article

  • Who should I run mysql as, on a personal computer?

    - by user664833
    I just installed mysql via homebrew (with brew install mysql, on Mac OS X Mountain Lion - recently installed from scratch). Following the installation, there is a "caveats" section with options around further necessary actions to take: ==> Caveats Set up databases to run AS YOUR USER ACCOUNT with: unset TMPDIR mysql_install_db --verbose --user=`whoami` --basedir="$(brew --prefix mysql)" --datadir=/usr/local/var/mysql --tmpdir=/tmp To set up base tables in another folder, or use a different user to run mysqld, view the help for mysqld_install_db: mysql_install_db --help and view the MySQL documentation: * http://dev.mysql.com/doc/refman/5.5/en/mysql-install-db.html * http://dev.mysql.com/doc/refman/5.5/en/default-privileges.html To run as, for instance, user "mysql", you may need to `sudo`: sudo mysql_install_db ...options... Start mysqld manually with: mysql.server start Note: if this fails, you probably forgot to run the first two steps up above A "/etc/my.cnf" from another install may interfere with a Homebrew-built server starting up correctly. To connect: mysql -uroot To launch on startup: * if this is your first install: mkdir -p ~/Library/LaunchAgents cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist * if this is an upgrade and you already have the homebrew.mxcl.mysql.plist loaded: launchctl unload -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist You may also need to edit the plist to use the correct "UserName". On previous versions of Mac OS X I ran mysql as mysql user, but now I am confronted by the idea of running it as myself. I am the only one who uses this computer (which happens to be my laptop), and I do programming for work and for pleasure. What are the pros & cons, or best practices, around choosing whether to run mysql AS YOUR USER ACCOUNT or as mysql or something else still?

    Read the article

  • TortoiseSVN client slows Explorer to a crawl in Windows XP running in Parallels

    - by Cory Larson
    I thought I'd make my first SuperUser question relatively simple, though it's the kind of question that may not get many responses as I'm not directly involved with the issue. A colleague does his development in Windows XP running in Parallels on his Mac. We've just migrated our VSS repository to SVN, and we've gone with TortoiseSVN as our client of choice with the Ankhsvn plugin for Visual Studio. On his XP instance, after installing TortoiseSVN, browsing through folders using Explorer is extremely slow; about 15 - 30 seconds before the contents of the next folder displays. It's the slowest when opening My Computer. Once he reaches a folder that contains the working content of an SVN project, Explorer behaves quickly again as expected. It seems that TortoiseSVN may be spending a bunch of time searching subfolders for stuff so it can do its icon-overlay thing, but that's just a guess. I've used TortoiseSVN for years on both XP and Vista on far less powerful machines without any issues with Explorer, so I'm attributing the slowness to it being run in a VM, though that may not be the actual issue. So has anyone encountered similar performance issues, and/or know of a fix? Keep in mind that any requests to make changes to his configuration will need to be communicated and thus my response time might be slow. Thanks everyone!

    Read the article

  • ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

    - by Stan
    I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

    Read the article

  • Could 0x800CCC0E in Outlook be caused by bad wireless connection?

    - by AndrejaKo
    I have a computer connected to a WiFi access point/router/modem. Sometimes, I get page not found errors and similar when opening a browser window, sometimes pings fail and it looks like the router's signal isn't very good. On the other hand, I get around 4 bars of signal strength in windows and graph looks good in Inssider. I also never get dropped connection to the router. My main problem is that I often get errors (such as 0x800CCC0E) in Outlook 2010 that after some searching appear to be connected to bad server connection. I'm using GMail over IMAP and all settings are correct. I didn't have similar errors on my previous router, but I'm not 100% sure that they appeared after switching to current one. It may have worked for some time without errors. There are also around 3000 messages on the server and the size of mailbox is around 12 GiB, which may contribute to the problems. On the other hand, there are at least 24 other networks in the 2.4 GHz range which I'm using and the number may have increased since I switched routers. Should I try solving this by getting a router with stronger signal?

    Read the article

  • Pull network or power? (for contianing a rooted server)

    - by Aleksandr Levchuk
    When a server gets rooted (e.g. a situation like this), one of the first things that you may decide to do is containment. Some security specialists advise not to enter remediation immediately and to keep the server online until forensics are completed. Those advises are usually for APT. It's different if you have occasional Script kiddie breaches. However, you may decide to remediate (fix things) early and one of the steps in remediation is containment of the server. Quoting from Robert Moir's Answer - "disconnect the victim from its muggers". A server can be contained by pulling the network cable or the power cable. Which method is better? Taking into consideration the need for: Protecting victims from further damage Executing successful forensics (Possibly) Protecting valuable data on the server Edit: 5 assumptions Assuming: You detected early: 24 hours. You want to recover early: 3 days of 1 systems admin on the job (forensics and recovery). The server is not a Virtual Machine or a Container able to take a snapshot capturing the contents of the servers memory. You decide not to attempt prosecuting. You suspect that the attacker may be using some form of software (possibly sophisticated) and this software is still running on the server.

    Read the article

  • Intel Motherboard Lightning Victim Dies Hard

    - by Stetson RDT
    Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

    Read the article

  • Free blog sites where the blogs can (if the template does) validate as XHTML Strict 1.0?

    - by Deleted
    I'm looking for a site where I may register a free blog and have the blog validate as XHTML Strict 1.0. On the surface this may seem like a trivial problem only related to the theme/template in use, but that's unfortunately not the case. One example of a provider which can't fullfill this requirement is Blogger. Altough the pages of the blogs there presents themselfs as XHTML 1.0 Strict it is impossible to actually comply with the requirements inheritied by that markup type in the blog (as the XHTML which is generated by Blogger makes the page as a whole invalid). I've sent a mail to Tumblr to see if it was possible with them, but so far my reply consists of them having forwarded my mail with a "suggestion" to the development department. I don't know if we had a communication error or if I'm actually going to receive a proper answer later. Time will tell. I haven't had time to investigate Tumblr myself, so they may very well be the solution to this problem. To sum things up, I'm looking for any provider: Of a free blog. The blog must have the capability to validate as XHTML Strict 1.0. With capability I mean that the system shouldn't get in the way of creating/using a theme which complies as XHTML Strict 1.0. Preferably is large or at least likely to stay around for a couple of years to come. But I'm willing to take my chances if none of the established providers are up to the task. Thank you for reading! I hope you know of any provider which would be suitable, preferably with proof by linking to a blog there which validates. I'm not looking for suggestions to look into, as there are far to many to investigate and far too little time. If you know of something for sure, I'd be very happy to know about it.

    Read the article

  • Running Solr on VPS problem

    - by Camran
    I have a VPS with Ubuntu OS. I run solr om my local machine (windows xp laptop) just fine. I have configured Jetty, and Solr just the same way as on my computer, but on the server. I have also downloaded the JRE and installed it on the server. However, whenever I try to run the start.jar file, the PuTTY terminal shows a bunch of text but gets stuck. I could pase the text here but it is very long, so unless somebody wants to see it I wont. Also, I cant view the solr admin page at all. Does anybody have experience in this kind of problem? Maybe java isn't correctly installed? It is a VPS so maybe installation is different. Thanks UPDATE: These are the last lines from the terminal, in other words, this is where it stops every time: INFO: [] webapp=null path=null params={event=firstSearcher&q=static+firstSearcher+warming+query+from+solrconfig.xml} hits=0 status=0 QTime=9 May 28, 2010 8:58:42 PM org.apache.solr.core.QuerySenderListener newSearcher INFO: QuerySenderListener done. May 28, 2010 8:58:42 PM org.apache.solr.handler.component.SpellCheckComponent$SpellCheckerListener newSearcher INFO: Loading spell index for spellchecker: default May 28, 2010 8:58:42 PM org.apache.solr.core.SolrCore registerSearcher INFO: [] Registered new searcher Searcher@63a721 main Also you should know that I installed jetty by just dragging the folders from my HD to the VPS server.

    Read the article

  • Remote Desktop Services Licensing - Does server have to have a RDS role?

    - by transistor1
    I recently set up a "micro" size Windows 2008 Datacenter server on Amazon AWS. My small group needs several concurrent RDS users to be able to access the machine. Without installing the "Remote Desktop Server" role, it allows 2 concurrent connections. I read on MS' website that in order to set up multiple users, we needed to install the RDS role. I did so, but now the application we are trying to share is running much slower than it was before. Prior to the role installation, it was taking about 5 seconds to open; now it is taking a few minutes to open -- without any other users logged on except me. My assumption is that the RDS role may be too much for this micro instance to handle, and currently, changing to another size instance is not an option (it may be possible later if we were to receive enough funding). This leads me to the following questions: 1) Is it a sensible assessment to assume that it is the RDS role is slowing things down, or are there other things that I could look at to speed it up? We are talking about a machine with ~600MB of memory. 2) If I revert back to the pre-RDS role, is there any legitimate way (in terms of purchasing RDS licenses) to get more than 2 concurrent desktops? I did read this, and am not questioning that the answerer is knowlegeable; but someone else may have some other experience. I am also making it clear that we want to do this in a legitimate way. Thanks in advance for any assistance that can be provided! EDIT: if it is helpful in answering the question, the application in question is a Lotus Approach database. Also, I am asking this from a technical perspective: not a legal one. I want to know if it is possible to install valid licenses without the RDS role.

    Read the article

  • Apache intermittently aborting requests

    - by Adam Phillips
    I have just been dealing with a problem whereby http requests are being aborted, seemingly at random. On any particular page in the website, when you opened a page, a number of the assets (img, css, etc) failed to load. If you refreshed, the page may work fine, the same set of assets may fail to load or different assets may fail to load. The net tab in firefox was returning 'Aborted' in the HTTP status code column for the failed assets, even tho in the case of images, the image previews were still working. There was nothing in any of the apache logs about the requests that failed, however since it seemed to point to an apache issue, we restarted apache. The first time we tried, it made no difference but about 10 minutes later, in the absence of a better solution we tried again. Bizarrely, the problem disappeared immeadiately. So now the site seems to be running fine again but its rather unsettling, both the intermittent nature of the problem and the lack of an explanation for its resolution. Has anyone seen anything like this before and if so did you find out the reason behind it? Many Thanks

    Read the article

  • Reverse web proxy with time constraints

    - by user2893458
    I have a web application which produces several unique URLs of the type http://service.company.com/service.html?type=aaaa&key=jfiZm6u6cW where the last part is a randomly generated key. Each such URL provides access to an instance of the service provided. I am looking for a way to restrict access to those URLs based on time constraints, as an example URL#1 should be available between 8:00AM and 10:00AM on May 30, URL#2 should be available between 10:30AM and 12:00PM on May 31, and so on. I already have a resource scheduling application based on Drupal and would like to find a way to include those URLs as scheduled resources. The web application is deployed on Apache Tomcat, so I don't have the knowledge or the resources to alter it, therefore I thought that I could put some sort of reverse proxy in front of the web app that could implement the time constraint feature. In my thoughts the reverse proxy would allow or disallow access to each URL based on the rules that my scheduling application would provide. There may be other ways to deliver such a solution, but I can't think of anything better, so the question is: is there a reverse web proxy architecture that could allow access to the destination URLs based on time and date rules? Any other ideas are more than welcome.

    Read the article

  • Remotely port forward/launch process or a client-less remote desktop app?

    - by DC177E
    I have an XP box running Logmein at a remote location behind a linksys router, which was running well for a whole of four days, until we had a power failure. Our ISP gave us a new IP, the machine restarted, and logmein did not autorun (or, at least, it did not automatically sign in), and our service (which may or may not be a Minecraft server with non-backed-up save files) also did not run upon startup. Logmein does not register the new IP (it still displays the old one). I have a DDNS updater service, so I do know the new dynamic address. I have tried using the built in XP remote desktop service, but, as with almost all non-cloud-based remote desktop services, it requires a port forward. Thus, I would appreciate it if anyone has any ideas as to: A: Any way of accessing our router remotely to forward the remote desktop port. I've seen the Remote Management option (forwarding the setup page to port 8080), but I do not have it enabled. I've tried UPnP, but again, the setup page for our router is not forwarded. B: Any way of remotely launching a process that does not require port forwarding (or uses ports 255XX, 18XXX, or 9000.), such as a remote console service built into XP. I realize this is a near impossibility. C: A Way to remotely start logmein, and sign in, which is likely a definite impossibility. Sorry if this is too specific for Stackexchange, or if I've put it into the wrong section (is SuperUser the correct place for this?). Ideas would, again be much appreciated, as shot-in-the-dark-like this may be.

    Read the article

  • Why can I not edit, delete directories inside of this directory

    - by user43053
    Hello there, First, I thought this was PHP related, but maybe it isn't. My original post, which may be irrelevant now is located at the bottom. The problem is I have a directory : /articles/. In it are 10 sub directories. I have been changing the permissions lately, but now it seems all the permissions of the parent folder, sub-folders and files are either chmod 755 or 777. I cannot move, delete or edit files inside of this parent directory or sub-directories with my FTP-client. I can however edit, delete, create new files and directories and change them with PHP-functions without problems. What may the problem be? OLD POST. Ignore everything below this line: If I create a directory with mkdir(), or create a file with fopen(), file_put_contents() or SimpleXMLElement::asXML(), I am unable to access the file with my FTP-client or c-Panel File Manager. If I try to delete or edit them, I get errors. Dreamweaver suggests it is a permission problem or a network or filesystem fault (but I've set the permissions with chmod() to 0777, and when I check the cPanel, it confirms chmod 777. I also tried to use fileowner() and the function returns int(99), the same owner as those files that I could access with my FTP-client. It seems files and directories created with PHP can only be modified or be deleted with PHP. I thought this must be a server setup related issue, so I write it here. I am on a shared server, and I have no idea about setting up servers. EDIT: It seems the problem is different. I cannot move files with FTP-client to the parent, or sub-directories either. This problem may not be PHP related, then. It seems the problem applies to any directory, regardless of whether it was created by PHP. EDIT 2: The parent directory has chmod 755. Thank you for your time. Kind regards Marius

    Read the article

  • Windows OS level file open event trigger

    - by john
    Colleagues, I have need to run a script/program on certain basic OS level events. In particular when a file in Windows is opened. The open may be read-only or to edit, and may be initiated by a number of means, either from windows explorer (open or ), be selected from a viewing or editing application from the native file chooser, or drag-n-drop into an editing or viewing application. Further, i need the trigger to "hold" the event from completing the action until the runtime on the program has completed. The event handler program may return a pass state, or fail state. If fail state has been returned, then the event must disallow the initially requested action. Lastly, I need to add to the file in question a property or attribute that will contain metadata that will be used by the above event trigger handler program to make a determination as to the pass/fail condition that will ultimately determine if the user is permitted to open the file. Please note that this is NOT a windows event log situation, but one at the OS level file open event. thanks very much for your help. regards, j

    Read the article

  • Why is negation of a regex needed?

    - by Lazer
    There are so many questions on regex-negation here on SO. I am not sure I understand why people feel the need to negate a regex. Why not use something like grep -v that shows only the results that do not match the regex? $ ls april august december february january july june march may november october september $ ls | grep ber december november october september $ ls | grep -v ber april august february january july june march may

    Read the article

  • Very slow compile times on Visual Studio

    - by johnc
    We are getting very slow compile times, which can take upwards of 20+ minutes on dual core 2GHz, 2G Ram machines. A lot of this is due to the size of our solution which has grown to 70+ projects, as well as VSS which is a bottle neck in itself when you have a lot of files. (swapping out VSS is not an option unfortunately, so I don't want this to descend into a VSS bash) We are looking at combing projects (not nice, as we like the separation of concerns, but is a good opportunity to refactor away some dead wood). We are also looking at having multiple solutions to achieve greater separation of concerns and quicker compile times for each element of the application. This I can see will become a dll hell as we try to keep things in synch. I am interested to know how other teams have dealt with this scaling issue, what do you do when your code base reaches a critical mass that you are wasting half the day watching the status bar deliver compile messages UPDATE Apologies, I neglected to mention this is a C# solution. Thanks for all the cpp suggestions, but it's been a few years since I've had to worry about headers. At a distance I say I miss C++, but I'm not sure I want to go back EDIT: Nice suggestions that have helped so far (not saying there aren't other nice suggestions below, just what has helped) New 3GHz laptop - the power of lost utilization works wonders when whinging to management Disable Anti Virus during compile 'Disconnecting' from VSS (actually the network) during compile - I may get us to remove VS-VSS integration altogether and stick to using the VSS UI Still not rip-snorting through a compile, but every bit helps. Orion did mention in a comment that generics may have a play also. From my tests there does appear to be a minimal performance hit, but not high enough to sure - compile times can be inconsistent due to disc activity. Due to time limitations, my tests didn't include as many Generics, or as much code, as would appear in live system, so that may accumulate. I wouldn't avoid using generics where they are supposed to be used, just for compile time performance WORKAROUND We are testing the practice of building new areas of the application in new solutions, importing in the latest dlls as required, them integrating them into the larger solution when we are happy with them. We may also do them same to existing code by creating temporary solutions that just encapsulate the areas we need to work on, and throwing them away after reintegrating the code. We need to weigh up the time it will take to reintegrate this code against the time we gain by not having Rip Van Winkle like experiences with rapid recompiling during development.

    Read the article

  • unable to login in to phpbb through session of wesite

    - by pramod4u
    With the below code we unable to session ingrate please help us how to integrate is there any modification let give modification. Thank you <?php session_start(); include "conn.php"; include "PHPBB_Login.php"; echo $_SESSION['username']; $data=mysql_query("select * from people where username='".$_SESSION['username']."'"); $data_data=mysql_fetch_array($data); echo $_SESSION['username']; $_SESSION['username']=$data_data['username']; echo $_SESSION['username']; $phpbbq=mysql_query("select user_id from phpbb_users where username='".$data_data['username']."'"); $phpbbr=mysql_fetch_array($phpbbq); //echo $phpbbr['user_id']; $id=$phpbbr['user_id']; $phpbb->login($id ); ?> <? class PHPBB_Login { function PHPBB_Login() { } function login($phpbb_user_id) { $id=$phpbb_user_id ; global $db, $board_config; global $HTTP_COOKIE_VARS, $HTTP_GET_VARS, $SID; // Setup the phpbb environment and then // run through the phpbb login process // You may need to change the following line to reflect // your phpBB installation. require_once('./phpBB-3.0.7-PL1/phpBB3/config.php'); define('IN_PHPBB',true); // You may need to change the following line to reflect // your phpBB installation. $phpbb_root_path = "./phpBB-3.0.7-PL1/phpBB3/"; require_once( $phpbb_root_path . "extension.inc" ); require_once( $phpbb_root_path . "common.php" ); // return session_begin($id,$user_ip, PAGE_INDEX, FALSE, TRUE ); return session_begin($id,$user_ip, PAGE_INDEX, FALSE, $autologin, '0'); } function logout( $session_id, $phpbb_user_id ) { global $db, $lang, $board_config; global $HTTP_COOKIE_VARS, $HTTP_GET_VARS, $SID; // Setup the phpbb environment and then // run through the phpbb login process // You may need to change the following line to reflect // your phpBB installation. require_once( './phpBB-3.0.7-PL1/phpBB3/config.php' ); define('IN_PHPBB',true); // You may need to change the following line to reflect // your phpBB installation. $phpbb_root_path = "./phpBB-3.0.7-PL1/phpBB3/"; require_once( $phpbb_root_path . "extension.inc" ); require_once( $phpbb_root_path . "common.php" ); session_end( $session_id, $phpbb_user_id ); // session_end doesn't seem to get rid of these cookies, // so we'll do it here just in to make certain. setcookie( $board_config[ "cookie_name" ] . "_sid", "", time() - 3600, " " ); setcookie( $board_config[ "cookie_name" ] . "_mysql", "", time() - 3600, " " ); } } ?>

    Read the article

  • Masked Time control in WPF

    - by Ashish Ashu
    We are in need of a control in which we can show the elapsed time in "Hour:Min:Sec" format. This control should have a spin control attached with it. Whenever we spin the spin window, it should increment the selected option ( Either hour, or min , or sec). Also the Hour may have values between 0 to 99 , Min many have values between 0 to 59 and Sec may have values between 0 to 59. Is anybody know this type of control in WPF?

    Read the article

  • Master/Detail insert using BCP?

    - by Joseph
    I've a master table with identity on for the primary key and I've some child tables. When I insert a record to the master table using BCP, how can I use the newly created ID from the master table to insert in the related child tables (May be BCP again)? Will it be possible? I may be able to set identity off, but, will it work? Thanks Joseph

    Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >