Search Results

Search found 18191 results on 728 pages for 'single board'.

Page 73/728 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• How do I easily repair a single unreadable block on a Linux disk?

  - by Nelson

  My Linux system has started throwing SMART errors in the syslog. I tracked it down and believe the problem is a single block on the disk. How do I go about easily getting the disk to reallocate that one block? I'd like to know what file got destroyed in the process. (I'm aware that if one block fails on a disk others are likely to follow; I have a good ongoing backup and just want to try to keep this disk working.) Searching the web leads to the Bad block HOWTO, which describes a manual process on an unmounted disk. It seems complicated and error-prone. Is there a tool to automate this process in Linux? My only other option is the manufacturer's diagnostic tool, but I presume that'll clobber the bad block without any reporting on what got destroyed. Worst case, it might be filesystem metadata. The disk in question is the primary system partition. Using ext3fs and LVM. Here's the error log from syslog and the relevant bit from smartctl. smartd[5226]: Device: /dev/hda, 1 Currently unreadable (pending) sectors Error 1 occurred at disk power-on lifetime: 17449 hours (727 days + 1 hours) ... Error: UNC at LBA = 0x00d39eee = 13868782 There's a full smartctl dump on pastebin.

  Read the article

• MsMpEng.exe (Windows Defender?) uses a lot of CPU at startup and runs two instances on a single core

  - by dlamblin

  I'm using Windows XP Professional SP2 on a single core AMD64 processor, and I've got two instances of MsMpEng.exe starting up when I start up and log in. They use 64MB and 32MB of ram and 140MB and 80MB of virtual memory, and fluctuate around 80% CPU usage for about 5 minutes at start up. They are (I read) associated with Windows Defender, but I'm concerned about: There's two of them, everything I read generally has only one reported. They might be scanning each other, and I want that to stop. They might be getting scanned by avgrsx.exe (AVG Free 8) (uses about 16Mb v ram) They might also be scanning moe.exe (assosciated with ms live mesh, which I'm considering getting rid of) Lastly I have Microsoft Security Essentials. I don't know the process name associated there. The main concern of mine (apart from the double instances) is that these are all trying to prioritize scanning each other at once except maybe moe.exe. This might seem legitimate but is likely a useless drain on resources. Have I made a mistake in having all of these installed, or is there a way to inform them not to do whatever they're doing that's taking about 5+ minutes at start up? [I also have Google Desktop, but I'm keeping that.] Comment if none of this makes sense to you.

  Read the article

• Can I use IIS to do ActiveDirectory single-sign-on for another website?

  - by brofield

  I'm trying to add Active Directory single-sign-on support to an existing SOAP server. The server can be configured to accept a trusted reverse-proxy and use the X-Remote-User HTTP header for the authenticated user. I want to configure IIS to be the trusted proxy for this service, so that it handles all of the Active Directory authentication for the SOAP server. Basically IIS would have to accept HTTP connections on port X and URL Y, do all the authentication, and then proxy the connection to a different server (most likely the same X and Y). Unfortunately, I have no knowledge of IIS or AD (so I am trying my best to learn enough to build this solution) so please be gentle. I would assume that this is not an uncommon scenario, so is there some easy way to do this? Is this sort of functionality built into IIS or do I need to build some sort of IIS proxy program myself? Is there a better option for getting the authentication done and the X-Remote-User HTTP header set than requiring IIS? Update: For example, what I am trying to create is: [CLIENT] [IIS] [AD] [SOAP-SERVER] 1. |---------------->| 2. |<--------------->|<---------->| 3. |--------------------------->| 4. |<---------------------------| 5. |<----------------| 1. POST to http://example.com/foo/bar.cgi 2. Client is not authenticated, so do authentication 3. Once validated, send request to server (X-Remote-User: {userid}) 4. Process request, send response 5. Forward response to client I need to know how to configure IIS to do the automatic authentication of the user using AD, and then to proxy the request to the actual server, sending the userid in the X-Remote-User HTTP header.

  Read the article

• Simple Linux program that takes any HTTP/HTTPS request and returns a single page?

  - by ultrasawblade

  I have a Linux box operating as router. There's a NIC that's connected to the internet (WAN), a NIC connected to an 8-port GbE switch (LAN), and a NIC connected to a Linksys wireless N-router (WLAN). Routing between everything is working perfectly. I have security completely disabled on the wireless router, but the WLAN NIC is firewalled such that it will only accept DNS queries and PPTP VPN connections. Currently HTTP/HTTPS traffic and everything else is blocked. I would like to run something that listens on port 80/443 of the WLAN NIC, and, for non VPN'ed connections, given any HTTP/HTTPS request it will return a single webpage saying "Unauthenticated" and explain how to sign into the VPN. A transparent proxy seems to be what I need, but my searches all seem to direct me to Squid, which is already running on my server and seems overkill for this simple task. Is there a simpler, lightweight program out there that does just this or should I just suck it up and run two instances of Squid (or figure out how to configure it)? Or, is this entire VPN thing I'm doing complete nonsense and I should just enable encryption on the wireless router?

  Read the article

• Can I use a single SSLCertificateFile for all my VirtualHosts instead of creating one of it for each VirtualHost?

  - by user65567

  I have many Apache VirtualHosts for each of which I use a dedicated SSLCertificateFile. This is an configuration example of a VirtualHost: <VirtualHost *:443> ServerName subdomain.domain.localhost DocumentRoot "/Users/<my_user_name>/Sites/users/public" RackEnv development <Directory "/Users/<my_user_name>/Sites/users/publ`enter code here`ic"> Order allow,deny Allow from all </Directory> # SSL Configuration SSLEngine on #Self Signed certificates SSLCertificateFile /private/etc/apache2/ssl/server.crt SSLCertificateKeyFile /private/etc/apache2/ssl/server.key SSLCertificateChainFile /private/etc/apache2/ssl/ca.crt </VirtualHost> Since I am maintaining more Ruby on Rails applications using Passenger Preference Pane, this is a part of the apache2 httpd.conf file: <IfModule passenger_module> NameVirtualHost *:80 <VirtualHost *:80> ServerName _default_ </VirtualHost> Include /private/etc/apache2/passenger_pane_vhosts/*.conf </IfModule> Can I use a single SSLCertificateFile for all my VirtualHosts (I have heard of wildcards) instead of creating one of it for each VirtualHost? If so, how can I change the files listed above?

  Read the article

• Windows 7 mouse multi selection on windows explorer with CTRL and point to select / single click to open

  - by bortao

  This is something that have annoyed me since i changed to Windows 7. I don't do double click for a long time now since windows introduced 1 click selection (Folder Options Click items as follows Single click to open an item). The problem is, when i click Control and hover over the items, they select/deselect automatically every small amount of mouse movement i make. What i want is to select/deselect the items only when i enter/exit them. So to deselect an item im hovering, i have to move the mouse out of it, and then back in. I'm using Intellimouse Explorer official drivers. (edit) Here's another related annoyance: When you are hovering something and move the mouse inside other item (Holding Ctrl) The new item may or may not be selected. If you continue moving the mouse it gets selected/deselected as you move. (more edit) I have found that the parameter HKCU\Control Panel\Mouse\MouseHoverHeight / MouseHoverWidth have some influence here. If it's set to 2, the item select/deselect really quickly as you move the mouse. When set to larger numbers, its slower. But setting to 20 or 200 don't seem to be much different.

  Read the article

• Strategy to isolate multiple nginx ssl apps with single domain via suburi's?

  - by icpu

  Warning: so far I have only learnt how to use nginx to serve apps with their own domain and server block. But I think its time to dive a little deeper. To mitigate the need for multiple SSL certificates or expensive wildcard certificates I would like to serve multiple apps (e.g. rails apps, php apps, node.js apps) from one nginx server_name. e.g. rooturl/railsapp rooturl/nodejsapp rooturl/phpshop rooturl/phpblog I am unsure on ideal strategy. Some examples I have seen and or thought about: Multiple location rules, this seems to cause conflicts between the individual app config requirements, e.g. differing rewrite and access requirements Isolated apps by backend internal port, is this possible? Each port routing to its own config? So config is isolated and can be bespoke to app requirements. Reverse proxy, I am little ignorant of how this works, is this what I need to research? is this actually 2 above? Help online seems to always proxy to another server e.g apache What is an effective way to isolate config requirements for apps served from a single domain via sub uris?

  Read the article

• A methology that allows for a single Java code base covering many different versions?

  - by Thorbjørn Ravn Andersen

  I work in a small shop where we have a LOT of legacy Cobol code and where a methology has been adopted to allow us to minimize forking and branching as much as possible. For a given release we have three levels: CORE - bottom layer, this code is common to all releases GROUP - optional code common to several customers. CUSTOMER - optional code specific for a single customer. When a program is needed, it is first searched for in CUSTOMER, then in GROUP and finally in CORE. A given application for us invokes many programs which all are looked for in this sequence (think exe files and PATH under Windows). We also have Java programs interacting with this legacy code, and as the core-group-customer lookup mehchanism does not lend it self easily to Java it has tended to grow in a CVS branch for each customer, requiring much too much maintainance. The Java part and the backend part tend to be developed in parallel. I have been assigned to figure out a way to make the two worlds meet. Essentially we want a Java enviornment which allows us to have a single code base with sources for each release, where we easily can select a group and a customer and work with the application as it goes for that customer, and then easily switch to another codeset and THAT customer. I was thinking of perhaps a scenario with an Eclipse project for each core, customer, and group and then use Project Sets to select those we need for a given scenario. The problem I cannot get my head about, is how we would create robust code in the CORE projects which will work regardless of which group and customer is selected. A Factory class which knows which sub class of a passed Class object to invoke instead of each and every new? Others must have had similar code base management problems. Anybody with experiences to share? EDIT: The conclusion to this problem above has been that CVS needs to be replaced with a source code management system better suited for dealing with many branches concurrently and the migration of source from one component to the other while keeping history. Inspired by the recent migration by slf4j and logback we are currently looking at git as it handles branches very well. We've considered subversion and mercurial too but git appears to be better for single location, multibranched projects. I've asked about Perforce in another question, but my personal inclination is towards open source solutions for something as crucial as this. EDIT: After some more pondering, we've found that our actual pain point is that we use branches in CVS, and that branches in CVS are the easiest to work with if you branch ALL files! The revised conclusion is that we can do this with CVS alone, by switching to a forest of java projects, each corresponding to one of the levels above, and use the Eclipse build paths to tie them together so each CUSTOMER version pulls in the appropriate GROUP and CORE project. We still want to switch to a better versioning system but this is so important a decision so we want to delay it as much as possible. EDIT: I now have a proof-of-concept implementation of the CORE-GROUP-CUSTOMER concept using Google Guice 2.0 - the @ImplementedBy tag is just what we need. I wonder what everybody else does? Using if's all over the place? EDIT: Now I also need this functionality for web applications. Guice was until the JSR-330 is in place. Anybody with versioning experience? EDIT: JSR-330/299 is now in place with the JEE6 reference implementation Weld based on JBoss Seam and I have reimplemented the proof-of-concept with Weld and can see that if we use @Alternative along with ... in beans.xml we can get the behaviour we desire. I.e. provide a new implementation for a given functionality in CORE without changing a bit in the CORE jars. Initial reading up on the Servlet 3.0 specification indicates that it may support the same functionality for web application resources (not code). We will now do initial testing on the real application.

  Read the article

• Replace dual-XP installs with single-XP install and repartition drive?

  - by caeious

  Hello, The Current Situation I have a hard drive that currently is split up like so: Primary Partition C: 9.77 GB NTFS Healthy (System) with XP Pro (in Polish) installed Extended Partition D: 39.82 GB NTFS Healthy (Boot) with XP Pro (in English) installed 6.30 GB Free space When I start my comuter I get a black and white Windows Boot Manager dual boot screen with 2 choices both being Microsoft Windows XP. The first choice is the English version of XP and the second choice is the Polish version of XP. Images of my Computer Management window and Dual Boot screen The Mission What I need to do is get rid of the entire extended partition (D: 39.82 GB & 6.30 free space) and just have the one primary C: drive which I assume will be somewheres around 55 GB big. So in the end I just want XP Pro in English running on my C: drive and no black and white boot screen to show up when starting up my laptop. The Question How do I go about successfully completing The Mission with out making my computer a useless pile of silicon, plastic and metal? UPDATE: So I went ahead and tried to follow Neal's suggestion but hit a wall. I got to a Windows XP Pro install screen that had the 3 following options as well as my drive data: To set up Windows XP on the selected item, press Enter To create a partition in the unpartitioned space, press C To delete the selected partition, press D 57232 MB Disk 0 at Id 0 on bus 0 on atapi [MBR] C: Partition1 [NTFS] 10001 MB ( 4642 MB free ) Unpartitioned space 6448 MB D: Partition2 [NTFS] 40774 MB ( 26225 MB free ) Unpartitioned space 8 MB I figured I would go with the first choice ((To set up Windows XP on the selected item, press Enter)) because I just wanted to set up Windows XP on C: Partition1 (which was preselected) so I pressed Enter which brought me to a screen displaying this message: You chose to install Windows XP on a partition that contains another operating system. Installing Windows XP on this partition might cause the other operating system to function improperly. CAUTION: Installing multiple operating systems on a single partition is not recommended. So this leads me to 2 new questions: How do I get rid of the Windows XP (Polish language) install on C: Partition 1 so that I can cleanly and safely install Windows XP (English language) on it? Neal, is this what you meant by me possibly having to delete the partition that the Windows XP (Polish language) install was located on? Since I have the option to delete partitions with the 3rd choice ((To delete the selected partition, press D)), should I do that on this screen or wait until I have Windows XP (English language) safely installed on C: Partition 1? I have to ask these questions because I have read that it is possibly dangerous to delete hard drive partitions. Just being cautious.

  Read the article

• VirtualBox - multiple guests, each with a single bridged adapter?

  - by Martin

  I am running a dedicated server (located at Hetzner, Germany) that runs VirtualBox in order to virtualize several services accross multiple virtual guests. Those guests are supposed to communicate with each other (for instance, a virtual web server has to access a virtual database server); to be reachable from the dedicated server (for instance, SSH access); and to access the Internet via the dedicated server (for instance, to download security updates) Currently, this is achieved by having host-only adapter vboxnet0 on the dedicated server and two virtual interfaces on each guest. There, virtual adapter eth0 is attached to vboxnet0 (to achieve (1) and (2)), virtual adapter eth1 is attached to VirtualBox' NAT (to achieve (3)). Via eth0, the guests have access to a DHCP and a DNS server, both running on the dedicated server (there, bound to vboxnet0). This allows me to assign custom IP addresses and names. Via eth1, VirtualBox pushes a proper route that enables each guest to access the Internet (via eth0 on the dedicated server). This setup with two virtual adapters frequently leads to problems and at leasts complicates many things. For instance, on the dedicated server there is OpenVPN which allows to access the virtual machines via the Internet; futhermore, there is Shorwall that controls the incoming and outgoing network traffic between the Internet, the dedicated server, and the individual virtual machines. Not to mention automatic installation of servers via PXE... Therefore, I would prefer to have only one single virtual adapter on each guest which would be used for both incoming and outgoing connections. As far as I understand, one would basically use a bridged interface for that very purpose. Now the question arises: Which interface on the dedicated server would the bridge use? eth0 on the host server is not an option, as this is prohibited by the provider. A virtual interface eth0:0 would not make any sense, as a bridge always uses a physical interface (eth0 in this case). Would it be possible to create a bridged interface in each virtual machine that would "dangle in the air"? Thus, without a complement on the dedicated server? How would I have to set up the routing on the host server? Please note that the host / dedicated server has only one network adapter (eth0) which is connected to the provider's network. Regards, Martin

  Read the article

• Server 2012 intermittently fails to respond to pings from single host, even with firewall disabled, but responds to non-ICMP requests fine

  - by James Westbury

  This one is kind of weird. I've got the following machines involved: DC01 - 10.1.2.42, Server 2012, domain controller & DNS server, physical machine nagiosv - 10.1.2.35, CentOS 6.4, Nagios, virtual machine CB01 - 10.1.3.81, Ubuntu 12.04 LTS, couchbase server, virtual machine So, I noticed something was wrong while configuring this new Nagios VM. I started seeing DC01's state flapping. I logged into nagiosv when I saw this happening, and attempted to ping DC01, both by FQDN and its IP address. Neither worked. I tried pinging the machine from CB01, which is another VM on the same virtual switch/physical NIC as nagiosv, and that worked fine. Pings still failing from nagiosv at this time. DC01 is also an internal DNS server, so I ran dig google.com from nagiosv, and was able to run a query against DC01 just fine: ;; Query time: 1 msec ;; SERVER: 10.1.2.42#53(10.1.2.42) ;; WHEN: Fri Nov 1 07:53:51 2013 ;; MSG SIZE rcvd: 204 Pings still failing from nagiosv, though. I can ping from DC01 to nagiosv, and that works, and I can still ping from other VMs on the same physical NIC into DC01, and that works. I should mention at this point that I've disabled the firewall on DC01 for testing purposes, and it doesn't make a damned bit of difference. (Even with the firewall enabled, I have a blanket exception for ICMP from the local subnet, so it shouldn't make a difference, but I figured I should test it anyway.) I loaded up Wireshark on DC01 and pinged it from nagiosv again. What I see is a bunch of echo requests coming in and not a single reply going back out. Filtered results here, showing all ICMP traffic during a 15-second period. A few more bits of info: There are no IP conflicts on the network. MAC addresses on the incoming pings match the MAC on the VM. There are no duplicate MACs on the network, as far as I can see. I have absolutely no idea why DC01 is failing to respond, here. Any ideas?

  Read the article

• Mock versus Implementation. How to share both approaches in a single Test class ?

  - by Arthur Ronald F D Garcia

  Hi, See the following Mock Test by using Spring/Spring-MVC public class OrderTest { // SimpleFormController private OrderController controller; private OrderService service; private MockHttpServletRequest request; @BeforeMethod public void setUp() { request = new MockHttpServletRequest(); request.setMethod("POST"); Integer orderNumber = 421; Order order = new Order(orderNumber); // Set up a Mock service service = createMock(OrderService.class); service.save(order); replay(service); controller = new OrderController(); controller.setService(service); controller.setValidator(new OrderValidator()); request.addParameter("orderNumber", String.valueOf(orderNumber)); } @Test public void successSave() { controller.handleRequest(request, new MockHttpServletResponse()); // Our OrderService has been called by our controller verify(service); } @Test public void failureSave() { // Ops... our orderNumber is required request.removeAllParameters(); ModelAndView mav = controller.handleRequest(request, new MockHttpServletResponse()); BindingResult bindException = (BindingResult) mav.getModel().get(BindingResult.MODEL_KEY_PREFIX + "command"); assertEquals("Our Validator has thrown one FieldError", bindException.getAllErrors(), 1); } } As you can see, i do as proposed by Triple A pattern Arrange (setUp method) Act (controller.handleRequest) Assert (verify and assertEquals) But i would like to test both Mock and Implementation class (OrderService) by using this single Test class. So in order to retrieve my Implementation, i re-write my class as follows @ContextConfiguration(locations="/app.xml") public class OrderTest extends AbstractTestNGSpringContextTests { } So how should i write my single test to Arrange both Mock and Implementation OrderService without change my Test method (sucessSave and failureSave) I am using TestNG, but you can show in JUnit if you want regards,

  Read the article

• R: dev.copy2pdf, multiple graphic devices to a single file, how to append to file?

  - by Timtico

  Hi everybody, I have a script that makes barplots, and opens a new window when 6 barplots have been written to the screen and keeps opening new graphic devices whenever necessary. Depending on the input, this leaves me with a potential large number of openened windows (graphic devices) which I would like to write to a single PDF file. Considering my Perl background, I decided to iterate over the different graphics devices, printing them out one by one. I would like to keep appending to a single PDF file, but I do not know how to do this, or if this is even possible. I would like to avoid looping in R. :) The code I use: for (i in 1:length(dev.list()) { dev.set(which = dev.list()[i] dev.copy2pdf(device = quartz, file = "/Users/Tim/Desktop/R/Filename.pdf") } However, this is not working as it will overwrite the file each time. Now is there an append function in R, like there is in Perl. Which allows me to keep adding pages to the existing pdf file? Or is there a way to contain the information in a graphic window to a object, and keep adding new graphic devices to this object and finally print the whole thing to a file? Other possible solutions I thought about: writing different pdf files, combining them after creation (perhaps even possible in R, with the right libraries installed?) copying the information in all different windows to one big graphic device and then print this to a pdf file.

  Read the article

• Null Pointer Exception on a 2D array (Java)

  - by user315156

  I have a class, "Tetris", in which one of the instance variables is "board". "board" is 2D array of Color objects. Upon the creation of a tetris object I call a method that sets the dimensions of board and then sets all of the Color objects to be the Default value, that is to say, Color.blue. public Tetris(int rows, int cols){ this.rows = rows; this.cols = cols; reset(rows, cols); } public void reset(int rows, int cols){ Color[][] board = new Color[rows][cols]; for(int i = 0; i Unfortunately, when I run the code (which obviously has not been posted in its entirety) I get a null pointer exception on the line: board[i][j] = DEFAULT_COLOR; // Color.blue; //DEFAULT-COLOR. Is there anything obviously wrong with what I am doing? (Sorry if there are glaring format issues, this is my first time on Stack Overflow)

  Read the article

• Linq Query Performance , comparing Compiled query vs Non-Compiled.

  - by AG.

  Hello Guys, I was wondering if i extract the common where clause query into a common expression would it make my query much faster, if i have say something like 10 linq queries on a collection with exact same 1st part of the where clause. I have done a small example to explain a bit more . public class Person { public string First { get; set; } public string Last { get; set; } public int Age { get; set; } public String Born { get; set; } public string Living { get; set; } } public sealed class PersonDetails : List<Person> { } PersonDetails d = new PersonDetails(); d.Add(new Person() {Age = 29, Born = "Timbuk Tu", First = "Joe", Last = "Bloggs", Living = "London"}); d.Add(new Person() { Age = 29, Born = "Timbuk Tu", First = "Foo", Last = "Bar", Living = "NewYork" }); Expression<Func<Person, bool>> exp = (a) => a.Age == 29; Func<Person, bool> commonQuery = exp.Compile(); var lx = from y in d where commonQuery.Invoke(y) && y.Living == "London" select y; var bx = from y in d where y.Age == 29 && y.Living == "NewYork" select y; Console.WriteLine("All Details {0}, {1}, {2}, {3}, {4}", lx.Single().Age, lx.Single().First , lx.Single().Last, lx.Single().Living, lx.Single().Born ); Console.WriteLine("All Details {0}, {1}, {2}, {3}, {4}", bx.Single().Age, bx.Single().First, bx.Single().Last, bx.Single().Living, bx.Single().Born); So can some of the guru's here give me some advice if it would be a good practice to write query like var lx = "Linq Expression " or var bx = "Linq Expression" ? Any inputs would be highly appreciated. Thanks, AG

  Read the article

• Single Responsibility Principle usage how can i call sub method correctly?

  - by Phsika

  i try to learn SOLID prencibles. i writed two type of code style. which one is : 1)Single Responsibility Principle_2.cs : if you look main program all instance generated from interface 1)Single Responsibility Principle_3.cs : if you look main program all instance genareted from normal class My question: which one is correct usage? which one can i prefer? namespace Single_Responsibility_Principle_2 { class Program { static void Main(string[] args) { IReportManager raporcu = new ReportManager(); IReport wordraporu = new WordRaporu(); raporcu.RaporHazirla(wordraporu, "data"); Console.ReadKey(); } } interface IReportManager { void RaporHazirla(IReport rapor, string bilgi); } class ReportManager : IReportManager { public void RaporHazirla(IReport rapor, string bilgi) { rapor.RaporYarat(bilgi); } } interface IReport { void RaporYarat(string bilgi); } class WordRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Word Raporu yaratildi:{0}",bilgi); } } class ExcellRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Excell raporu yaratildi:{0}",bilgi); } } class PdfRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("pdf raporu yaratildi:{0}",bilgi); } } } Second 0ne all instance genareted from normal class namespace Single_Responsibility_Principle_3 { class Program { static void Main(string[] args) { WordRaporu word = new WordRaporu(); ReportManager manager = new ReportManager(); manager.RaporHazirla(word,"test"); } } interface IReportManager { void RaporHazirla(IReport rapor, string bilgi); } class ReportManager : IReportManager { public void RaporHazirla(IReport rapor, string bilgi) { rapor.RaporYarat(bilgi); } } interface IReport { void RaporYarat(string bilgi); } class WordRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Word Raporu yaratildi:{0}",bilgi); } } class ExcellRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Excell raporu yaratildi:{0}",bilgi); } } class PdfRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("pdf raporu yaratildi:{0}",bilgi); } } }

  Read the article

• How can I render a custom view in a UIScrollView at varying zoom levels without distorting the view?

  - by eczarny

  The scenario: I have a custom view (a subclass of UIView) that draws a game board. To enable the ability to zoom into, and pan around, the board I added my view as a subview of UIScrollView. This kind of works, but the game board is being rendered incorrectly. Everything is kind of fuzzy, and nothing looks right. The question: How can I force my view to be redrawn correctly ay varying scales? I'm providing my view with the current scale and sending it a setNeedsDisplay message after the scroll view is done zooming in/out, but the game board is still being rendered incorrectly. My view should be redrawing the game board depending on the zoom level, but this isn't happening. Does the scroll view perform a generic transformation on subviews? Is there a way to disable this behavior?

  Read the article

• Best way to get a single value from a DataTable?

  - by PiersMyers

  I have a number of static classes that contain tables like this: using System; using System.Data; using System.Globalization; public static class TableFoo { private static readonly DataTable ItemTable; static TableFoo() { ItemTable = new DataTable("TableFoo") { Locale = CultureInfo.InvariantCulture }; ItemTable.Columns.Add("Id", typeof(int)); ItemTable.Columns["Id"].Unique = true; ItemTable.Columns.Add("Description", typeof(string)); ItemTable.Columns.Add("Data1", typeof(int)); ItemTable.Columns.Add("Data2", typeof(double)); ItemTable.Rows.Add(0, "Item 1", 1, 1.0); ItemTable.Rows.Add(1, "Item 2", 1, 1.0); ItemTable.Rows.Add(2, "Item 3", 2, 0.75); ItemTable.Rows.Add(3, "Item 4", 4, 0.25); ItemTable.Rows.Add(4, "Item 5", 1, 1.0); } public static DataTable GetItemTable() { return ItemTable; } public static int Data1(int id) { DataRow[] dr = ItemTable.Select("Id = " + id); if (dr.Length == 0) { throw new ArgumentOutOfRangeException("id", "Out of range."); } return (int)dr[0]["Data1"]; } public static double Data2(int id) { DataRow[] dr = ItemTable.Select("Id = " + id); if (dr.Length == 0) { throw new ArgumentOutOfRangeException("id", "Out of range."); } return (double)dr[0]["Data2"]; } } Is there a better way of writing the Data1 or Data2 methods that return a single value from a single row that matches the given id?

  Read the article

• How can I create a horizontal table in a single foreach loop in MVC?

  - by GenericTypeTea

  Is there any way, in ASP.Net MVC, to condense the following code to a single foreach loop? <table class="table"> <tr> <td> Name </td> <% foreach (var item in Model) { %> <td> <%= item.Name %> </td> <% } %> </tr> <tr> <td> Item </td> <% foreach (var item in Model) { %> <td> <%= item.Company %> </td> <% } %> </tr> </table> Where model is a simple object: public class SomeObject { public virtual Name {get;set;} public virtual Company {get;set;} } This would output a table as follows: Name | Bob | Sam | Bill | Steve | Company | Builder | Fireman | MS | Apple | I know I could probably use an extension method to write out each row, but is it possible to build all rows using a single iteration over the model? This is a follow on from this question as I'm unhappy with my accepted answer and cannot believe I've provided the best solution.

  Read the article

• How can I know the IP address of a remote host by using UDP broadcast message?

  - by khera-satinder

  Hi All, I am developing an embedded system and very new to this TCP\IP. My problem is that once I installed my board in a local network and this board will acquire its IP address dynamically, it has to communicate with a client application running on one of the PC(other than DHCP server) in the network. To communicate with this new board the client application is required to know the IP address of the board. What is the way to know the IP address of the board? Will UDP broadcast work for this purpose? If yes please, explain in detail as I am unable to understand it. Please provide me some sample code in C if possible. Regards, Satinder

  Read the article

• Conditionally Summing the same Column multiple times in a single select statement?

  - by btollett

  I have a single table that shows employee deployments, for various types of deployment, in a given location for each month: ID | Location_ID | Date | NumEmployees | DeploymentType_ID As an example, a few records might be: 1 | L1 | 12/2010 | 7 | 1 (=Permanent) 2 | L1 | 12/2010 | 2 | 2 (=Temp) 3 | L1 | 12/2010 | 1 | 3 (=Support) 4 | L1 | 01/2011 | 4 | 1 5 | L1 | 01/2011 | 2 | 2 6 | L1 | 01/2011 | 1 | 3 7 | L2 | 12/2010 | 6 | 1 8 | L2 | 01/2011 | 6 | 1 9 | L2 | 12/2010 | 3 | 2 What I need to do is sum the various types of people by date, such that the results look something like this: Date | Total Perm | Total Temp | Total Supp 12/2010 | 13 | 5 | 1 01/2011 | 10 | 2 | 1 Currently, I've created a separate query for each deployment type that looks like this: SELECT Date, SUM(NumEmployees) AS "Total Permanent" FROM tblDeployment WHERE DeploymentType_ID=1 GROUP BY Date; We'll call that query qSumPermDeployments. Then, I'm using a couple of joins to combine the queries: SELECT qSumPermDeployments.Date, qSumPermDeployments.["Total Permanent"] AS "Permanent" qSumTempDeployments.["Total Temp"] AS "Temp" qSumSupportDeployments.["Total Support"] AS Support FROM (qSumPermDeployments LEFT JOIN qSumTempDeployments ON qSumPermDeployments.Date = qSumTempDeployments.Date) LEFT JOIN qSumSupportDeployments ON qSumPermDeployments.Date = qSumSupportDeployments.Date; Note that I'm currently constructing that final query under the assumption that a location will only have temp or support employees if they also have permanent employees. Thus, I can create the joins using the permanent employee results as the base table. Given all of the data I currently have, that assumption holds up, but ideally I'd like to move away from that assumption. So finally, my question. Is there a way to simplify this down to a single query or is it best to separate it out into multiple queries - if for no other reason that readability.

  Read the article

• How can I diff against a revision of a single file using only the default Git GUI tools?

  - by Rich

  I want to view the history of a single file, and then compare a single revision from that history against the current version. On the command line, this is easy: Run: git log -- <filename> Locate the version you want to compare, Run: git diff <commitid> -- <filename> But how can this be done using only the default Git gui tools, git gui and gitk? I know of two methods using gitk, but they're both horribly clunky: Either: Select the New View option from the View menu, Type in the full path to your file into the box labelled Enter files and directories to include, one per line, Locate the version you want to compare by looking at the highlighted items in the top pane, and click on it to select it, Right-click on the current version and select Diff selected - this, Or: Select Tree in the bottom right-hand pane, Locate the file you want to look at, right-click on it, and select Highlight this only, Locate the version you want to compare by looking at the highlighted items in the top pane, and click on it to select it, Right-click on the current version and select Diff selected - this, Click on the file in the bottom right-hand pane to jump to it in the diff output, or scroll manually. Is a better method than this?

  Read the article

• What are good strategies for organizing single class per query service layer?

  - by KallDrexx

  Right now my Asp.net MVC application is structured as Controller - Services - Repositories. The services consist of aggregate root classes that contain methods. Each method is a specific operation that gets performed, such as retrieving a list of projects, adding a new project, or searching for a project etc. The problem with this is that my service classes are becoming really fat with a lot of methods. As of right now I am separating methods out into categories separated by #region tags, but this is quickly becoming out of control. I can definitely see it becoming hard to determine what functionality already exists and where modifications need to go. Since each method in the service classes are isolated and don't really interact with each other, they really could be more stand alone. After reading some articles, such as this, I am thinking of following the single query per class model, as it seems like a more organized solution. Instead of trying to figure out what class and method you need to call to perform an operation, you just have to figure out the class. My only reservation with the single query per class method is that I need some way to organize the 50+ classes I will end up with. Does anyone have any suggestions for strategies to best organize this type of pattern?

  Read the article

• How to deploy a single webapp with multiple web-modules that may be removed or added individually

  - by Daniel Bleisteiner

  We currently run two separate webapps (WARs) deployed in one single EAR containing additional JARs and settings. To improve our deployment I want to split one of these webapps into different modules that may be build and packaged individually. But I've currently no clue on how to package these modules so that I'm able to add or remove them as desired - at best during runtime. The webapp is getting more and more complex and I'd like to separate some of the functionality into modules. These modules should be packaged as single archives. As long as they contain only classes and resources loaded through code I know how to do this (simple JARs). But how about JSPs? Normally a WAR file contains JSPs or HTML files. I my case it are JSF pages utilizing JBoss Seam and RichFaces. These modules will add classes, resources and JSF pages and other includes to the running webapplication. Is it somehow possible to deploy them as individual archives to serve the same running webapp? We are using Maven for our build and packaging and deploy into JBoss v4.

  Read the article

• How many WCF connections can a single host handle?

  - by mafutrct

  I'll try to explain this with an example. I'm writing a chat application. There are users that can join chat rooms. A user has to log in before he can join any room. Currently, there is a single service. A user logs in using this service. Then, the user sends and receives messages for all joined rooms via this single service. channel.Login("Hans Moleman", "password"); channel.JoinRoom("name of room"); channel.SendChat("name of room", "hello"); I'm thinking about changing the design so there is a new WCF connection for each joined room. In the actual app, the number of connections is likely going to be in the range of 10-100, possibly more. Is this a good idea? Or are ~100 connections per client too much? The server should be able to handle many clients (range 100-1000, later up to 10k). In case it matters, I'm using NetTcpBinding.

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >