Search Results

Search found 26086 results on 1044 pages for 'site to site vpn'.

Page 73/1044 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• Cannot access a very specific site from my router

  - by DJDarkViper

  This is a problem for me because this site is important to me. It's MY website. And sadly my email is hosted on my site (which I cant access either) When I try to access my website when connected to my Linksys E3000 router, these days it simply just doesn't go through. When I ping it, its all Request Timed Out, and when I tracert C:\Users\Kyle>tracert blackjaguarstudios.com Tracing route to blackjaguarstudios.com [199.188.204.228] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms CISCO26565 [192.168.1.1] 2 16 ms 15 ms 11 ms 11.4.64.1 3 11 ms 9 ms 11 ms rd1cs-ge1-2-1.ok.shawcable.net [64.59.169.2] 4 20 ms 21 ms 22 ms 66.163.76.98 5 37 ms 36 ms 35 ms rc1nr-tge0-9-2-0.wp.shawcable.net [66.163.77.54] 6 112 ms 84 ms 85 ms rc2ch-pos9-0.il.shawcable.net [66.163.76.174] 7 86 ms 89 ms 90 ms rc4as-ge12-0-0.vx.shawcable.net [66.163.64.46] 8 90 ms 84 ms 85 ms eqix.xe-3-3-0.cr2.iad1.us.nlayer.net [206.223.115.61] 9 97 ms 97 ms 99 ms xe-3-3-0.cr1.atl1.us.nlayer.net [69.22.142.105] 10 128 ms 128 ms 126 ms ae1-40g.ar1.atl1.us.nlayer.net [69.31.135.130] 11 101 ms 97 ms 96 ms as16626.xe-2-0-5-102.ar1.atl1.us.nlayer.net [69.31.135.46] 12 100 ms 97 ms 197 ms 6509-sc1.abstractdns.com [207.210.114.166] 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 * * * Request timed out. 17 * * * Request timed out. 18 * * * Request timed out. 19 * * * Request timed out. 20 * * * Request timed out. 21 * * * Request timed out. 22 * * * Request timed out. 23 * * * Request timed out. 24 * * * Request timed out. 25 * * * Request timed out. 26 * * * Request timed out. 27 * * * Request timed out. 28 * * * Request timed out. 29 * * * Request timed out. 30 * * * Request timed out. Trace complete. C:\Users\Kyle> SHAW Cable being my ISP. Figuring this was all something to do with some setting I made on the router, I reset the thing back to factory defaults. Nope. So I'm at a bit of a loss what to do here, as NO device (Computers, Laptops, Tablets, Phones, PS3/ 360, etc) can access my site or its features, so it's not just my computer either. But every other site is just fine. When I connect to my neighbors router, the site comes up just fine. And shes with SHAW as well. What should I do?!

  Read the article

• How do I sync a list on a site from a list on a subsite in SharePoint?

  - by mandroid

  Our group has a main site and a subsite dedicated to our projects. Each project has a project lead and a completion % associated with it. We have a list on the project site that goes to each project's dedicated subsite within the project site. I want to duplicate the list from the project site on the main site, where any changes or additions made to the project site list appears in the main site list as well including the project lead and completion %. How do I accomplish this? Here is a simple example of the hierarchy: Main site - Project list derived from Project list below Project Site - Project list Project 1 Site Project 2 Site Project 3 Site

  Read the article

• Handling site not found and page not found with dynamic mass virtual hosting

  - by Rick Moynihan

  I have recently setup mass virtual hosting in Apache so that all we need to do is create a directory to create a new vhost. We're then also using wildcard DNS to map all subdomains to the server running our Apache instance. This works excellently, however I'm now having trouble configuring it to fail-over to an appropriate default/error-page when the vhost directory does not exist. The problem appears to be conflated between by my desire to handle the two error conditions: vhost not found i.e. there was no directory found matching the host supplied in the HTTP host header. I'd like this to display an appropriate site not found error page. The 404 page not found condition of the vhost. Additionally I have a specialised "api" vhost in its own vhost block. I've tried a number of variations and none seem to exhibit the behaviour I want. Here's what I'm working with right now: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /var/www/site-not-found ServerName sitenotfound.mydomain.org ErrorDocument 500 /500.html ErrorDocument 404 /500.html </VirtualHost> <VirtualHost *:80> ServerName api.mydomain.org DocumentRoot /var/www/vhosts/api.mydomain.org/current # other directives, e.g. setting up passenger/rails etc... </VirtualHost> <VirtualHost *:80> # get the server name from the Host: header UseCanonicalName Off VirtualDocumentRoot /var/www/vhosts/%0/current # other directives ... e.g proxy passing to api etc... ErrorDocument 404 /404.html </VirtualHost> My understanding is that the first vhost block is used as the default, so I have this here as my catch all site. Next I have my API vhost, and then finally my mass vhost block. So for a domain that doesn't match the first two ServerName's and has no corresponding directory in /var/www/vhosts/ I'd expect it to fall-over to the first vhost, however with this setup, all domains resolve to my default site-not-found. Why is this? By putting the mass-vhost block first, I can get the mass-vhosts to resolve properly, but not my site-not-found vhost... and in this case I can't seem to find a way to distinguish between a page-level 404 in the vhost, and the case where the VirtualDocumentRoot fails to find a vhost directory (this appears to use the 404 also). Any help out of this bind is much appreciated!

  Read the article

• How to Eliminate Tape Backup and Off-site Storage Service?

  - by Daniel Lucas

  PLEASE READ UPDATE AT THE BOTTOM. THANKS! ;) Environment Info (all Windows): 2 sites 30 servers site #1 (3TB of backup data) 5 servers site #2 (1TB of backup data) MPLS backbone tunnel connecting site #1 and site #2 Current Backup Process: Online Backup (disk-to-disk) Site #1 has a server running Symantec Backup Exec 12.5 with four 1TB USB 2.0 disks. BE jobs for full backups run nightly on all servers in site #1 to these disks. Site #2 backs up to a central file server there using software they already had when we purchased them. A BE job pulls that data nightly to site #1 and stores them on said disks. Off-site Backup (tape) Connected to our backup server is a tape drive. BE backs up the external disks to tape once a week which gets picked up by our off-site storage company. Obviously we rotate two tape libraries, one is always here and one is always there. Requirements: Eliminate the need for tape and off-site storage service by doing disk-to-disk at each site and replicating site #1 to site #2 and vice versa. Software based solution as hardware options have been too pricey (ie, SonicWall, Arkeia). Agents for Exchange, SharePoint, and SQL. Some Ideas So Far: Storage DroboPro at each site with an initial 8TB of storage (these are expandable up to 16TB at present). I like these because they are rackmountable, allow disparate drives, and have iSCSI interfaces. They are relatively cheap too. Software Symantec Backup Exec 12.5 already has all the agents and licenses we need. I'd like to keep using it unless there is a better solution, similarly priced, that does everything BE does plus deduplication and replication. Server Because there is no more need for a SCSI adapter (for tape drive) we are going to virtualize our backup server as it is currently the only physical machine save for SQL boxes. Problems: When replicating between sites we want as little data as possible to go across the pipe. There is no deduplication or compression in what I have laid out here so far. The files being replicated are BE's virtual tape libraries from our disk-to-disk backup. Because of this each of those huge files will go across the wire every week because they change every day. And Finally, the Question: Is there any software out there that does deduplication, or at least compression, to handle just our site-to-site replication? Or, looking at our setup, is there any other solution that I am missing that might be cheaper, faster, better? Thanks. Sorry so long. UPDATE 2: I've set a bounty on this question to get it more attention. I'm looking for software that will handle replication of data between two sites using the least amount of data possible (either compression, deduplication, or some other method). Something similar to rsync would work but it needs to be native to Windows and not a port involving shenanigans to get up and running. Prefer a GUI based product and I don't mind shelling out a few bones if it works. Please, answers that meet the above criteria only. If you don't think one exists or if you think I'm being to restrictive keep it to yourself. If after seven days there is no answer at all, so be it. Thanks again everyone. UPDATE 2: I really appreciate everyone coming forward with suggestions. There is no way for me to try all of these before the bounty expires. For now I'm going to let this bounty run out and whoever has the most votes will get the 100 rep points. Thanks again!

  Read the article

• Google shows subdomain of main site instead of add on domain URL

  - by Welsher

  I have my host (lunarpages) set up with a few add on domains to my main account. These show up as sub-domains of my main account, but they can be reached by using the new domain I've created. So: subdomain1.domain.com -- www.mynewsite.com subdomain2.domain.com -- www.myothersite.com etc. The problem is, mynewsite.com shows up in google with that domain, but myothersite.com shows up with subdomain2.domain.com. I don't have a clue what might be causing this to happen. If anyone has an advice or can point me in the right direction, I'd really appreciate it! Thanks.

  Read the article

• Running Firewall (IPCop) on Hyper-V

  - by Loren Charnley

  I currently use IPCop for our corporate firewall & VPN. I am looking to consolidate a number of servers, and am considering including the firewall server in the consolidation. I currently plan on using Server 2008 with Hyper-V for the virtualization. Has anyone out there tried virtualizing IPCop? Is there anything that I should be aware of? In particular, IPCop has somewhat limited hardware support for NICs - what hardware will the VM see for the network card?

  Read the article

• Creating site with wix.com or weebly.com [on hold]

  - by Edgar

  I decided to create web page and for that purpose I find out that I can use wix.com portal. My knowledge of HTML,CSS is on basic level. So I want to ask what are pros and cons of creating webPages using WIX to compare with making your on your own (writing code by yourself). One of the questions is: can I put custom advertisements to the my page. Also would appreciate of suggestions what portal is better for wix.com or weebly.com or for good website I should choose codding by myself? Finally, would be nice to get any suggestions in this field.

  Read the article

• ignoring informational payload, type INVALID_COOKIE msgid=00000000

  - by user197279

  I'm configuring a site-to-site vpn between openswan ipsec and cisco asa 5540. After the step, i started ipesc service but the error i'm seeing is: ignoring informational payload, type INVALID_COOKIE msgid=00000000 Nov 5 09:42:30 pluto[11712]: "myVPN" #1: received and ignored informational message Nov 5 09:42:51 pluto[11712]: "myVPN" #1: ignoring informational payload, type INVALID_COOKIE msgid=00000000 Nov 5 09:42:51 pluto[11712]: "myVPN" #1: received and ignored informational message Nov 5 09:43:30 pluto[11712]: "myVPN" #1: max number of retransmissions (2) reached STATE_MAIN_I2 Nov 5 09:43:30 pluto[11712]: "myVPN" #1: starting keying attempt 2 of at most 3 Any advise why I'm getting this error on openswan? Also sudo ipsec whack --status gives: "myVPN": 10.0.xx.0/24===10.0.7x.x[54.209.y.yyy,+S=C]---10.0.xx.x...10.0.70.x---41.22x.4.xx<41.22x.4.xx[+S=C]===41.22y.4.yyy/32; unrouted; eroute owner: #0 000 "myVPN": myip=54.209.zz.zz; hisip=unset; 000 "myVPN": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 3 000 "myVPN": policy: PSK+ENCRYPT+TUNNEL+DONTREKEY+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,32; interface: eth0; 000 "myVPN": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 "myVPN": IKE algorithms wanted: AES_CBC(7)_256-SHA1(2)_000-MODP1024(2); flags=-strict 000 "myVPN": IKE algorithms found: AES_CBC(7)_256-SHA1(2)_160-MODP1024(2) 000 "myVPN": ESP algorithms wanted: AES(12)_256-SHA1(2)_000; flags=-strict 000 "myVPN": ESP algorithms loaded: AES(12)_256-SHA1(2)_160 000 000 #5: "myVPN":500 STATE_MAIN_I2 (sent MI2, expecting MR2); EVENT_RETRANSMIT in 8s; nodpd; idle; import:admin initiate 000 #5: pending Phase 2 for "myVPN" replacing #0 Thanks.

  Read the article

• SharePoint Personalization Site Links - Les liens personnalis?s des MySite SharePoint

  Nous avons vu dans les articles pr?c?dents comment agr?menter les pages de recherche afin de permettre une meilleure adoption du produit par les utilisateurs. Il existe une autre fonctionnalit? de Microsoft Office SharePoint Server 2007 (MOSS) qui permet aussi de personnaliser un peu le MySite des utilisateurs en ajoutant des liens directs.

  Read the article

• Security Trimmed Cross Site Collection Navigation

  Ad:: SharePoint 2007 Training in .NET 3.5 technologies (more information). This feed URL has been discontinued. Please update your reader's URL to : http://feeds.feedburner.com/winsmarts Read full article .... ...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Share openVPN connection

  - by Douglas Gemignani

  Hello, Currently I have a server (dev tun) running openVPN and my WinXP client is able to connect to the server just fine. I have an ethernet device and I need to send data to a computer under the server's network, so since the device can't connect on its own I need to configurate my Windows XP to share its VPN connection. So, on my WinXP machine i have: Network Adapter #1 (ip 192.168.0.2 gw 192.168.0.1 with internet access). OpenVPN Connection (dhcp). Network Adapter #2 (crossover cable with device). Here is my client.ovpn cert gertec.crt key gertec.key client ns-cert-type server user nobody group nobody remote IP PORT ca ca.crt dev tun dev-node OpenVPN proto udp resolv-retry infinite nobind comp-lzo verb 3 I would appreciate any help.

  Read the article

• Any problems usinga GoDaddy SSL certificate on a Cisco ASA firewall?

  - by Richard West

  I need to purchase and install a SSL certificate on my Cisco ASA firewall. This will allow my VPN users to connect to my ASA without receiving the certificate error from the untrusted self assigned SSL certificate that is currently on the ASA. I had good experiences with the SSL certificates that GoDaddy sells. However, I'm concerned about using them. On my web servers I have to also install GoDaddy's "intermediate certificate bundle". On the ASA I do not think that I will be able to preform anything like this. I do not fully understand what the "intermediate certificate bundle" does, but obviously it's important. So my question is can I use a GoDaddy SSL certificate on an ASA without my users getting any type of warning or error about connecting to a site that using an untrusted SSL certificate. I need this to be as simple as possible for my end users and warning messages are always scary :) Thanks!

  Read the article

• Using pfSense, OpenVPN Connects but Still Can't See the Network

  - by nicorellius

  I am having an OpenVPN issue. I have a pfSense box at home configured to allow traffic through a VPN tunnel. The client computer is Windows XP Home, behind a standard Comcast connection and a Netgear wireless router. I use OpenVPN to access my work network (from where I am trying to get out of in this post) from home (with an XP Pro machine behind pfSense), and this works fine. The client config is similar but has the changes specific to my setup... Here is my XP Home config: client dev tun proto tcp remote pfsense.*.org 1194 (starred out by me) resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 When I launch the OpenVPN GUI, the Tunnel TAP network connection turns red, and I can right-click that to connect to the server. Everything seems to work fine until I browse for the actual network. The Tunnel TAP connection turns green and it says connected to 10.1.1.6 (I have tried different IP pools here too with no luck). I can see the internal network fine, but my home network behind pfSense is not there. I have tried browsing there by using Tools Map Network Drive, using the browser, with no success. When I open the command line on the client and use the ipconfig -all command, I get the following: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TAP-Win32 Adapter V9 Physical Address. . . . . . . . . : *** (starred out by me) Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 10.1.1.6 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : DHCP Server . . . . . . . . . . . : 10.1.1.5 Lease Obtained. . . . . . . . . . : Monday, March 15, 2010 1:18:37 PM Lease Expires . . . . . . . . . . : Tuesday, March 15, 2011 1:18:37 PM I noticed that the default gateway is not present. Could this be my problem? I am still relatively new to firewalls, VPN, and network configuration so I'm sure I am messing up something simple. Oh yah, I should note that I have firewall rules configured for pfSense to allow traffic through the WAN and the LAN. At first there was just the WAN firewall rule, because that is what I got from the literature I was reading. I then created a LAN rule as well, but I'm not sure if this was correct. Neither way works, though. Screen shots below: Any help is much appreciated.

  Read the article

• Un-failing over a Cisco PIX 515e

  - by ABrown

  We had a power outage at our data center last week and when our dual PIX 515E running IOS 7.0(8) (configured with a failover cable) came back, they were in a failed over state where the Secondary unit is active and the Primary unit is standby I have tried 'failover reset', 'failover active', and 'failover reload-standby' as well as executing reloads on both units in a variety of orders, and they don't come back Primary/Active Secondary/Standby. The only thing in my arsenal that I haven't tried is driving to the data center and performing a hard reboot, which I hate to do. I have read How Failover Works on the Cisco Secure Firewall and it seems like this should be wicked straight forward. output of show failover on Primary: Failover On Cable status: Normal Failover unit Primary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:52:05 UTC Mar 10 2010 This host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Other host: Secondary - Active Active time: 897045 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. output of show failover on Secondary: Failover On Cable status: Normal Failover unit Secondary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:03:04 UTC Feb 28 2010 This host: Secondary - Active Active time: 896925 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Other host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. I'm seeing the following in my syslog: Mar 10 03:05:00 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:05:09 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reload-standby' command. Mar 10 03:05:12 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:05:12 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:06:09 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:06:10 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:06:10 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:06:23 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:06:23 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:06:24 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. Mar 10 03:07:05 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:07:31 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover active' command. Mar 10 03:08:04 fw1 %PIX-5-611103: User logged out: Uname: enable_1 Mar 10 03:08:04 fw1 %PIX-6-315011: SSH session from admin1_int on interface inside for user "pix" terminated normally Mar 10 03:08:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:08:39 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:09:10 fw1 %PIX-6-605005: Login permitted from admin1_int/36891 to inside:192.168.4.4/ssh for user "pix" Mar 10 03:09:23 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:09:38 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:09:52 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:09:52 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:09:53 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. I'm not exactly sure how to interpret that syslog data. Primary doesn't seem to even try to become Active. When I reload the individual units separately, my connections are retained, so it doesn't seem like I have a real hardware failure. Is there something I can query (IOS or SNMP) to check for hardware issues? Any thoughts? My IOS-fu is weak. Thanks for any help you might provide, Aaron

  Read the article

• A whole site for reviewing of SQL Server MVP Deep Dives

  - by Rob Farley

  This book just keeps amazing me. Not only as I read through some chapters for the first time, and others for the second and third times, but also as I read reviews of it written by other people. The guys over at http://sqlperspectives.wordpress.com are a prime example. They’ve been going through each chapter, each writing a review on it, and often getting a guest blogger to write something as well – and they’re clearly getting a lot of stuff out of this brilliant book. Back when I first heard about them doing this, I had offered to be involved, and recently did an interview with them about my chapters (chapter seven and chapter forty). That interview can be found at http://sqlperspectives.wordpress.com/2010/03/20/interview-with-rob-farley/ – and covers how I got into databases, and how I think the database roles in the IT industry are changing. If you don’t have a copy of SQL Server MVP Deep Dives yet, why not get a copy from http://www.sqlservermvpdeepdives.com (or persuade your local bookstore to get some copies in), and read through chapters with these guys? Treat it like a book club, discussing each chapter with others (guest blogging perhaps?), and you’ll probably end up getting even more out of it. Remember that the proceeds of the book go to charity (instead of the authors – we get nothing), so you don’t need to consider that you’re splashing out on a treat for yourself. Think of the kids helped by War Child instead. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• Iptables setup for PPTP server and UPnP on clients [on hold]

  - by SPYke

  I have a Debian server with one static external IP. It has PPTP server installed. Local IP is 192.168.1.200 and remote IPs are 192.168.1.201-209. I have several users, who connect to my server using their routers through the Internet. VPN work flawlessly. Routers have UPnP enabled, but devices, that use UPnP, are reporting no UPnP available. What rules do I need in iptables to make it work? Thanks.

  Read the article

• L2TP server on OpenVZ

  - by MikO

  I need to create a L2TP VPN server on a VPS in a OpenVZ container (I can install CentOS5, CentOS6, Ubuntu12.04 or Debian6). I have been reading and I think IPSEC does not work on OpenVZ, is this right? In fact I´m getting an error saying that it's not allowed in the kernel... But an important thing is that I don't have any security requirement at all for the transmissions I'll be doing. So, is there something I can do? Is there any way to set up a L2TP server without IPSEC?

  Read the article

• Can't RDP Into Windows Server After Windows Server Establishes VPN Session

  - by Jennifer Baker

  Hi there. I've setup a Windows 2008 Server in a Cloud Environment. I am able to RDP to this Windows Server ("aka CloudServer") in the Cloud Environment. When I establish PPTP VPN connection from the CloudServer back to our Windows Server ("aka OfficeServer"), my RDP session is dropped and it won't let me RDP back in. The only way how I can RDP to the CloudServer is using the DHCP ip address issued from the OfficeServer. What do I need to change on the CloudServer? Thanks in advance for your help! Jennifer

  Read the article

• 5 Important On-Site SEO Tweaks

  The first part of any successful search engine optimization (SEO) campaign, is to fully optimize all the parts of your website to get a high keyword density for your keywords. This article will focus on five important elements that should be optimized on every page of your website.

  Read the article

• Transferring FSMO roles over vpn

  - by Tom Bowman

  I have a server located at one of our offices which is quite old and is due to be upgraded soon, this server holds the FSMO roles, I have another server in another office, both are DC's in the same domain and both are replicated, both run Server 2003 standard. I need to transfer the FSMO roles from the old server to the the one I have in the other office before I upgrade. Also I am looking at bringing in Exchange 2010 server however I cant install/configure that until I transfer the roles as it needs to be at the same site as the schema master. My question really is as both servers replicate over a vpn, how quickly will the roles transfer and will there be downtime as I need to make sure that while the transfer is running, both servers will service logon's and share files. or would it be better to do it out of hours? many thanks and apologies if I've missed out anything Regards Tom

  Read the article

• Pancake.io Is a Dead Simple Way to Host a Web Site from Your Dropbox Account

  - by Jason Fitzpatrick

  Pancake.io is a web-based app that makes it dead simple to use your Dropbox account as as simple web host. Signup for an account and Pancake.io creates a folder in your Dropbox. You can modify the page in one of two ways: you can simply put files into the folder and use the simple template provided by Pancake.io to share them or you can edit the template (located in the Pancake.io folder) to customize the page. Hit up the link below to read more about Pancake.io and take it for a test drive. Pancake.io [via ReadWriteWeb] HTG Explains: How Hackers Take Over Web Sites with SQL Injection / DDoS Use Your Android Phone to Comparison Shop: 4 Scanner Apps Reviewed How to Run Android Apps on Your Desktop the Easy Way

  Read the article

• Allow traffic from ssl-vpn to enter ipsec tunnel on fortigate

  - by Sascha

  we configured our FortiGate 50B to route traffic from our local net 192.168.10.* (which is our office) to a remote network 172.29.112.* using an ipsec tunnel. Everything works fine as long my computer has an ip from 192.168.10.*. We can also connect to the office network from at home using a ssl vpn connection. Once connected we receive an ip from 10.41.41.*. Now I want to allow the traffic flow from 10.41.41.* to 172.29.112.* just like it does from the office network. Could somebody point me in the right direction what I would need to do? Thanks, Sascha

  Read the article

• Deploying Socket.IO App to Windows Azure Web Site with Azure CLI

  - by shiju

  In this blog post, I will demonstrate how to deploy Socket.IO app to Windows Azure Website using Windows Azure Cross-Platform Command-Line Interface, which leverages the Windows Azure Website’s new support for Web Sockets. Recently Windows Azure has announced lot of enhancements including the support for Web Sockets in Windows Azure Websites, which lets the Node.js developers deploy Socket.IO apps to Windows Azure Websites. In this blog post, I am using  Windows Azure CLI for create and deploy Windows Azure Website. Install  Windows Azure CLI The Windows Azure CLI available as a NPM module so that you can install Windows Azure CLI using  NPM as shown in the below command. After installing the azure-cli, just enter the command “azure” which will show the useful commands provided by Azure CLI. Import Windows Azure Subscription Account In order to import our Azure subscription account, we need to download the Windows Azure subscription profile. The Azure CLI command “account download” lets you download the  Windows Azure subscription profile as shown in the below command. The command redirect you login to Windows Azure portal and allow you to download the Windows Azure publish settings file. The account import command lets you import the downloaded publish settings file so that you can create and manage Websites, Cloud Services, Virtual Machines and Mobile Services in Windows Azure. Create Windows Azure Website and Enable Web Sockets In this post, we are going to deploy Socket.IO app to Windows Azure Website by using the Web Socket support provided by Windows Azure. Let’s create a Website named “socketiochatapp” using the Azure CLI. The above command will create a Windows Azure Website that will also initialize a Git repository with a remote named Azure. We can see the newly created Website from Azure portal. By default, the Web Sockets will be disabled. So let’s enable it by navigating to the Configure tab of the Website, and select “ON” in Web Sockets option and save the configuration changes. Deploy a Node.js Socket.IO App to Windows Azure Now, our Windows Azure Website supports Web Sockets so that we can easily deploy Socket.IO app to Windows Azure Website. Let’s add Node.js chat app which leverages Socket.IO module. Please note that you have to add npm module dependencies in the package.json file so that Windows Azure can install the dependencies when deploying the app. Let’s add the Node.js app and add the files to git repository. Let’s commit the changes to git repository. We have committed the changes to git local repository. Let’s push the changes to Windows Azure production environment. The successful deployment can see from the Windows Azure portal by navigating to the deployments tab of the selected Windows Azure Website. The screen shot below shows that our chat app is running successfully.   You can follow me on Twitter @shijucv

  Read the article

• IPSEC Windows 2008 <--> Fortinet 60B

  - by Elijah Glover

  I am trying to establish a IPSEC vpn, between an office DSL connection and a single virtual machine. I have done hub-spoke stuff before with cisco and fortinet routers, never hardware <-- software. Fortigate 60B - 10.20.1.1/24 Windows Server 2008 r2 Installed On VM I have seen some guides, to do this with juniper screenos (guide uses first release of 2008, they introduced windows firewall with advanced security), but none using fortinet equipment. Anyone ever been successful? Or should I install RAS/PPTP, so I can dial in?

  Read the article

• How do you decide site availability requirements?

  - by Nathan Long

  I work on a web application to file a specific kind of county taxes. Our company wants our state to mandate that counties must accept electronic filings (as opposed to paper) from any system that meets some sensible requirements for uptime, security, data validation, etc. (Yes, this would help us as a business, but it would also force county governments to be more efficient.) We're creating a draft of those requirements to be reviewed and tweaked with the state. One of the sections is "availability." We want to specify something reasonably high, but not so high that any unexpected problem will get us (or a competitor) penalized. How do we decide what's reasonable for availability requirements?

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >