Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 73/286 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

  • Two wireless NICs on a MacBook - can I bind all VPN traffic to one, and everything else to another?

    - by Ben Aston
    I frequently connect to my workplace over a VPN. I would like to continue watching videos from, say YouTube, whilst I work on the VPN, without degrading the available VPN bandwidth (say for an RDP session). Can I configure a second NIC to deal with only the VPN traffic, with everything else going over the primary? Specs as requested: Macbook Pro, OSX Snow Leopard, using the built in OSX VPN connectivity, the in-built airport card and a USB external wifi adapter.

    Read the article

  • Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

    - by ZiGi
    i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

    Read the article

  • Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

    - by ZiGi
    i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

    Read the article

  • Does a 300mbps 802.11n wireless connection have any noticeable speed improvement over 54mbps g?

    - by j j
    300mbps sounds wonderful, but not with my horrible Comcast internet connection. I doubt there's an internet connection in America that even hits 54mbps. So I'm guessing that the only reason someone would be inclined to upgrade is for faster data transfer within the local network. With my internet connection where download rates are rarely ever above a few hundred kilobytes a second, would I even see any improvement in switching from 802.11g to 802.11n?

    Read the article

  • Wireless Networking 802.11n

    It';s been years in development but this September it looks like 802.11n Wi-Fi will finally become a standard... well, an official standard anyway. Presently the majority of the wireless hardware you... [Author: Chris Holgate - Computers and Internet - April 08, 2010]

    Read the article

  • Wireless Adapter Review: hField Wi-Fire

    Tired of weak and wimpy WiFi? This clip-on replacement for your laptop's 802.11b/g adapter promises up to triple the range, plus finding wireless networks you couldn't access before. Is it the best $59 a road warrior ever spent?

    Read the article

  • Wireless Adapter Review: hField Wi-Fire

    Tired of weak and wimpy WiFi? This clip-on replacement for your laptop's 802.11b/g adapter promises up to triple the range, plus finding wireless networks you couldn't access before. Is it the best $59 a road warrior ever spent?

    Read the article

  • Dell Inspiron 1501 no wired/wireless w/12.04 or13.04

    - by Niven
    I don't know what to do. Every install of either 13.04 and 12.04 on my Dell does not have a working wired or wireless internet connection. However, if I am running from USB in the trial mode I have working internet through a wired connection using the same ethernet cord. I honestly at this point do not know what I can do to fix this issue as I have gone through every possible fix I have found here and in other places.

    Read the article

  • Microsoft Wireless Keyboard 3000 v2.0 doesnt recognize "Flip Key"

    - by Michael Clare
    The Microsoft Wireless Keyboard 3000 v2.0 has a new key called a "flip key" where the right windows button should be (to the right of the right alt key). This is a picture, the key in question is called "Windows Flip": http://www.microsoft.com/hardware/en-us/p/digital-media-keyboard-3000#details I am using Ubuntu 11.10 and this key is not recognized at all by the system: I have run "sudo showkey" with no results. Any help would be greatly appreciated, I would like to map this to be a Right-Super key as it should be.

    Read the article

  • Ubuntu stops letting wired or wireless mouse click through after random delay

    - by Jonathan Chan
    I have a very confusing problem that renders Ubuntu near unusable. Whenever I try to use any wired or wireless mouse with my Ubuntu 10.10 install, clicks stop going through - often times, this blockage of clicks happens in less than a minute. Sometimes no clicks are accepted, other times, clicks are accepted in certain windows and blocked in others. The end result is the same, and I am forced to resort to using the keyboard to navigate.

    Read the article

  • Wireless mouse temporarily freezes (sleeps) on battery power

    - by R Pennese
    I have been getting a very annoying problem since recently in Ubuntu 12.04, probably due to another update that did more bad than good... When I resume from sleep on battery power my Lenovo Thinkpad T420, my wireless laser mouse (Logitech M705) freezes everytime I leave it for 2 seconds. It then starts moving again when I shake it for 5 seconds. The touchpad works normally. I'm guessing the mouse enters some sleep mode and I'd like to know where to change this "timeout" value.

    Read the article

  • Why is Windows 7 not following all routes?

    - by GigabyteProductions
    My computer is connected to my secondary router that's running the 192.168.42.0/24 network and my computer also has a route that directs anything on that network to the router, but for anything on that network other than the router itself, it get's the ICMP response of Reply from 192.168.42.194: Destination host unreachable. (with 192.168.42.194 being my computer). Every other network works, like all of the internet, or addresses on my primary router like 192.168.1.*, just not on the 192.168.42.0/24 network... route print returns: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.42.1 192.168.42.194 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.42.0 255.255.255.0 On-link 192.168.42.194 276 192.168.42.194 255.255.255.255 On-link 192.168.42.194 276 192.168.42.255 255.255.255.255 On-link 192.168.42.194 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.42.194 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.42.194 276 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.42.1 Default =========================================================================== The only time anything is supposed to send an ICMP Host Unreachable response is when there's no route to it, right? So, why is my own computer sending that to ping or tracert when I have the route of 192.168.42.0 with the mask of 255.255.255.0? An IP address of 192.168.42.2 surely fits into that route. If I explicitly add a route for the IP address i am trying to access, it works, like: route add 192.168.42.2 mask 255.255.255.255 192.168.42.1 (the 192.168.42.1 right after mask is gateway, or the device to send the packet to so it can route it further), but why wont it work for the implicit route that's automatically on the table? I disabled my firewall, too (I use Comodo if anyone thinks this still serves as a problem). I'v even tried explicitly adding the gateway of 192.168.42.1 to the 192.168.42.0/24 route instead of it routing through 0.0.0.0's gateway, which is what On-link does. but that didn't work either, so it's not a gateway specification problem. If the host was really unreachable, it would be the router's IP address (192.168.42.1) sending that to me... This network is all of my creation, so there's no problem such as an administrator locking me out, because i am the administrator.

    Read the article

  • Connecting Wii to router to Proxy Server via VPN to BBC iPlayer

    - by nkimber
    I live in the USA and want to be able to watch UK TV streamed over the web. The relevant services are geographically crippled. I can do this by using a VPN proxy server in the UK, connecting to the VPN service using a straight Windows VPN connection. However, this means I have to watch everything on my PC. The BBC iPlayer works on the Wii in the UK. So, I'd like to connect my Wii to a wireless router (LinkSys WRT54G2) and have that be automatically connected via VPN to my proxy service in the UK. If I can do this then I'd be able to stream UK TV direct to my TV via the Wii. I thought I could have one router act as my VPN connection, connected to a 2nd router that connects to my Cable internet access. But this bit isn't working, any thoughts?

    Read the article

  • WRTU54G-TM T-Mobile@Home router with 3rd party firmware

    - by dlamblin
    I've been doing a lot of reading online about the Linksys WRTU54G-TM router model that I now own. It seems getting a custom firmware onto it is not a problem. But no one is talking about retaining the Voip features (yet). So far they're all disappointed that it's not a SIP machine and used GSM over IPSec. Personally I don't care about using it with non-t-mobile. If I take the original firmware, shouldn't I be able to extract it, and it's SquashFS image, and then move all of the t-mobile specific binaries for enabling the calling features over to a custom firmware installation (maybe OpenWRT)? You might ask why, and the reason is, that if I do this I could retain my calling features, which I do want, and ssh to the router and use it to run additional software, as any OpenWRT router could do. Does anyone know if this can be done, and how the firmware's binaries could be gotten at and installed correctly?

    Read the article

  • Wireless clients have no route to ethernet clients in OpenWrt router

    - by superjoe30
    I'm using OpenWrt Kamikaze 8.09 on a Linksys WRT54g v1.1 router. I just flashed it with default settings and got everything working, except my wireless laptop cannot ping my desktop which is wired to the router. What can I do to fix this? (My desktop can ping other desktops wired to the router) My routing table: config 'defaults' option 'syn_flood' '1' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'lan' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'wan' option 'input' 'REJECT' option 'output' 'ACCEPT' option 'forward' 'REJECT' option 'masq' '1' config 'forwarding' option 'src' 'lan' option 'dest' 'wan' option 'mtu_fix' '1' config 'redirect' option 'src' 'wan' option '_name' 'ssh' option 'proto' 'tcp' option 'src_dport' '22' option 'dest_ip' '192.168.1.100' option 'dest_port' '22' config 'redirect' option 'src' 'wan' option '_name' 'http' option 'proto' 'tcp' option 'src_dport' '8888' option 'dest_ip' '192.168.1.100' option 'dest_port' '8888'

    Read the article

  • Print server not being recognized after switching router and upgrading to 64 bit

    - by picardo
    I recently upgraded Windows 7 from 32 bit to 64 bit. I also switched my router from a very old model of Netgear to TP-Link. Before these updates, I had been using a USB print server by IOGear. After the updates, I took care to reinstall the drivers for both the print server and the printer, and picked the option to install a printer via TCP/IP, but no matter what I did, the driver software couldn't locate the print server on my network. I hit refresh, restarted my machine, turned off the firewalls and tried again. Still nothing. I'm at my wit's end. What else is left to try? Edit: More info. The print server is connected to the router via LAN line. The computer is connected to the router with a wireless connection.

    Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >