Search Results

Search found 39497 results on 1580 pages for 'two shoes'.

Page 730/1580 | < Previous Page | 726 727 728 729 730 731 732 733 734 735 736 737  | Next Page >

• afp/smb transfers caps at 2 megabytes/sec, wireless N

  - by CQM

  I wanted to transfer files between two mac computers. The network is wireless-N and both computers have wireless-N modules in them. The problem is that when I transfer files between them, via file sharing (afp) the network speed caps at 2 megabytes/sec. Just downloading files from the internet I can get faster speeds, so this isn't a constriction of my wifi bandwidth, it appears to be a constriction of the protocol being used. My wifi-n is set to 130mbits, so I should see real world transfer speeds around 12-16 megabytes/sec I did this command on both computers sudo sysctl -w net.inet.tcp.delayed_ack=0 which is supposed to lower tcp overhead, but this did not affect it. How can I get the speed I am expecting?

  Read the article

• Which software could I use to setup a 4in6 IP tunnel (RFC 2473) on GNU/Linux

  - by Mildred

  Here is my problem. I have a server A that has two IP addresses. One public IPv4 and one IPv6. Server B has only one IPv6 address. I want to host most of my services on server B (because I have more disk space on it, I can control it better) but I need the IPv4 of the server A. I would like to set up a 4in6 tunnel (RFC 2473) between A and B so that I can transfer the traffic from the IPv4 address in A to B. If needed, I can request another IPv4 address on the server A, but I'd prefer not to. My question is: which software use to do the 4in6 tunnelling? I suppose OpenVPN can do the thing, but is there any implementation of the 4in6 protocol on Linux? A little more challenging: the IPv4 address comes from a venet interface, which cannot be bridged. How could I transfer ownership of this address I don't use on server A to the server B? Thank you

  Read the article

• second ip address on the same interface but on a different subnet

  - by fptstl

  Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

  Read the article

• Blue Screen Of Death after Graphics Card Update

  - by John Smith

  I recently installed the game watch dogs After installing it i upgraded the drivers on my graphics card AMD Radion R9 200 series via the catalyst software and since then windows has been crashing on an ad-hoc basis even when sitting idle I have recieved two different sets of errors OXOOOOOOO1 and VIDEO_SCHEDULER_INTERNAL_ERROR I am running windows 8.1 with the driver 14.4 from AMD My PC shouldnt really be having this problem as it is pretty high spec due to my work Any help would be greatly appreciated as it is driving me up the walls a bit [UPDATE 08-06-2014] I have been looking around online and have crashed the PC a few times now trying to recreate the bug I have looked into the event history viewer and gotten the following errors amdacpusrsvc acpusrsvc: IOCTL_ACPKSD_KSD_TO_USR_SVC_SET_FB_APERTURES: FAILED acpusrsvc: GfxMemServiceInitialize: FAILED amdacpusrsvc acpusrsvc: IOCTL_ACPKSD_KSD_TO_USR_SVC_SET_FB_APERTURES: FAILED amdacpusrsvc acpusrsvc: GfxMemServiceInitialize: FAILED I took some advice from the AMD forums to re-install the old drivers to see if they would work. I uninstalled the old ones first and installed directly from the CD I got the warnings below but the driver installed "successfully" The Warnings are amdacpusrsvc acpusrsvc: ConfigureFrameBufferMemory: FAILED. Hopefully this will spark something off for someone Thanks John

  Read the article

• Virtual PC network connection setting issue

  - by George2

  Hello everyone, I am using Virtual PC 2007 on Windows Vista Enterprise x86. My confusion is about the network setting for guest OS. In the network setting, I can set the network adaptor of guest OS to one of my physical network adaptors of my host OS (I have tested that it works for guest OS to use the physical network adaptor of host OS to access external network). But in this way, 1. since both host OS and guest OS will use the same physical network adaptor, will there be any conflicts (e.g. same H/W serves two OS)? 2. will guest OS share a part of network bandwidth of the host OS of the physical network adaptor? 3. What means NAT setting in guest OS network connection adaptor? thanks in advance, George

  Read the article

• X locks up with konqueror on comics.com

  - by retracile

  If I browse to comics.com using konqueror under KDE on Fedora 11, X will, after a delay, lock up. The mouse will move, but no keyboard input is recognized, and the screen does not react to the mouse passing over objects on screen. I am able to ssh into the machine and issue shutdown -r now and have that work. The machine is a Dell XPS M1330 with Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c), and Fedora 11 is fully updated. Visiting the same site in Firefox does not cause a lockup. I am booting with nomodeset since it won't boot into X otherwise. I tried the other two accel options: EXA (still locks up) and XAA (X won't start). Any suggestions on how I can debug this? bugzilla

  Read the article

• Suggest me solution to track the change in test DB and replicate in Another DB

  - by Pranav

  Suggest me solution to track the change in test DB and replicate in Another DB... My Client need a script or any solution, if he has two Database, One Test DB in which he tests his data on test portal and if he find it appropriate he can use those changes to be done in main DB to display on Live site.. Fior this he needs the solution to record or track all updation/deletion/insertion, so that he can do the same in main DB if found appropriate, NOTE: we have only one server, no separate server, hence binary log replication doesnt seems to be working for my case..

  Read the article

• Standalone firewall + antivirus or combined security tools?

  - by pukipuki

  For years I'm using some antivirus software and different firewall. Now every antiviruses have got some firewall features and there are complete "internet security" complexes... and every firewall get some antivirus functionality and there are "internet security" versions. Firstly, it is hard and sometimes impossible to install and use standalone AV and FW. Sometimes I can't avoid them (i can't install KAV2010 without removing Outpost firewall etc). Secondly, complex solutions have some disbalance. Farewall from famous antivirus-brand is so user-friendly that is not suitable for me (lack of details in Norton Internet Security for example) and antiviruses from famous firewall-brands are still weak, it is proved by tests. What is today best-practices in case of functionality and security?) Some internet-security complex or two standalone applications from different vendors?

  Read the article

• Virtual system drive is split between separate LUNs

  - by Tigran

  My hardware VMWare guy told me that a Win2008R2 server I have has a D drive that is split between two separate LUNs. He could not tell me if that's a good thing or bad just that it's not standard practice for him. Would you please explain the benefits or drawbacks of this setup? Thanks EDIT Some additional info. What happened was I had D drive already allocated. Then I asked for more. They said there's no more space on whatever LUN my D drive is on so the option they gave me was that part of the D drive will be on one LUN and other part will be on another LUN. Hope that helps

  Read the article

• Determining who is running with administrator rights?

  - by Alex C.

  I work at a small non-profit organization with about 55 desktop PCs running Windows XP Pro. The domain controller is running Windows Server 2003. I have a two-part question (note that I'm a bit of a newb when it comes to network administration). Part 1: Is there some simple way that I can determine which accounts are logged in with administrator rights? Part 2: Is there a way that I can remove administrator rights from users without sitting down at each individual machine? Thanks for considering my questions.

  Read the article

• Ulimit settings in Oracle 11g on Linux 5

  - by Stuart

  Is there an issue with "Ulimit -Hn" being set too low (at 1024) when (Oracle recommend 65536)? This is for Oracle 64-bit 11g on Linux 5. It is one of the settings that appears to be woefully short of its recommendation. But I am also aware that the database server in question is an Oracle Data Guard Local Standby and should only really have a connection or two from its Primary database server (to ship the redo logs across). The Local Standby database server has 'hung' about 3 times in as many months and then requires a reboot. I do not have access to this server, so rely on others to look at logs etc. The sanity check on kernel params uncovered the low value for "ulimit -Hn". Has anyone ever seen that 'low' value cause a hang or crash?

  Read the article

• Can't access VirtualBox host-only network from windows host

  - by Markus Orreilly

  I've got two vms running on a windows host, each with a host-only network and ips in the 192.168.56.XXX range. One of them is running apache and serving some content that I want to access from my windows host. However, the windows host can't access the apache server at all. The server is running on 192.168.56.103. ipconfig from windows says it's ip for the Virtual Box interface is 169.254.143.37. I tried route add to route 192.168.56.XX traffic, but everything I tried didn't work and I was probably using it wrong. Any ideas on how to make this work?

  Read the article

• How to bind Apache to specific IP and port on Windows Server 2008

  - by webworm

  I have a Windows Server 2008 R2 that I use to host various ASP.NET applications under IIS7. I would also like to run various PHP based web apps using Apache (or Apache 2). The server has three static IP addresses assigned to it and I would like to bind one of the IP addresses to Apache while using the other two IP addresses for IIS. I can use the IIS Manager to bind the specific IP addresses to IIS, but I am unaware of how to do this with Apache. Can anyone tell me how to go about binding Apache to a specific IP address and port (port 80 is what I want to use). Please note .. I am aware that PHP can run under IIS. In fact that is how I have been running my PHP web applications. However, there are so many inconsistencies and pitfalls with PHP running under IIS that I just prefer to use Apache.

  Read the article

• 59 vs 60 hertz on external display via DisplayPort

  - by Shiki

  Don't know if this is a really specific question or you'll help me out. Please do. I just bought a DeLock DisplayPort cable for my Lenovo T500. Tried to use it with the in-built Intel MHD4500, no use. With the ATI HD3650 (you can switch between the two vga on this machine) I get a normal picture, but only on 59hz. On 60 I get a smaller desktop size (strange). Any idea what can cause this? Will I have any problem if I use the 59hz? (Was using the display with a VGA cable but I get a blurry picture with that (dont matter what device I attach, VGA is like this on this display) and thats why I wanted to change.)

  Read the article

• "Reboot and select proper boot device"?

  - by overtherainbow

  Hello I didn't find the answer in Clonezilla's site/mailing list archives. Maybe someone has already seen this issue and knows how to recover from it: On a test host, using www.partedmagic.com, I created two partitions: One to hold an OS I wish to use for testing (/sda1), and a second partition to hold images (/sda2) After trying out Windows7, I used CloneZilla to restore an XPSP3 image, but I get the following error message when rebooting: "Reboot and select proper boot device" Could it be that Clonezilla didn't save/restore the MBR? Gparted didn't let me set a partition as "active", so it could also be this, but I have no idea. Thank you for any help.

  Read the article

• Serial number not found, copy of Windows not genuine

  - by sara

  I have an HP-G71-340US notebook that I purchased 11/29/09. When I power it up, a black screen comes on that shows "serial number not found" and it also says that my copy of Windows 7 Home Basic is not genuine – but my computer came with Windows 7 Home Premium. In BIOS, my serial number is not shown either and I did pull out the little battery to reset it which allowed me to bypass the suddenly new locked BIOS that needed a password to enter. I'm sure this is a masterpiece created by my 6 or 9 yr old child while trying to play on my laptop. Can I fix these two problems?

  Read the article

• Stop yahoo from opeing in second tab when opening chrome

  - by sam

  I recently downloaded Vuze (torrent client), which as well as installing, installs a whole bunch of rubbish toolbars (mostly by an outfit called 'Spigot') and tries to change your default search engine to Yahoo. In Safari and Firefox, ive managed to change it back but i Chrome although ive deleted all the addons and restored my default search engine when ever i open up Chrome i get two tabs 1) my default homepage and 2) yahoo search page. Any idea were i can disable this Yahoo search page, ive looked in the settings but could find any where obvious (ive set back my default search engine to Google and deleted any add ons) but this still dosnt do it.. any ideas ? My last resort is to do a factory reset of Chrome, which i dont want to do as i have all my settings in there.

  Read the article

• Couple folders went 'access denied' in Windows. Why and how to fix?

  - by Nathaniel

  So, after a failed Windows 7 install, I put XP back on, and had a adrenaline shot when I got an access denied on a couple of my backed up folders. I already tried the instructions here at Microsoft KB, but it didn't fix it. I did add myself with full permissions on the main section of the Security tab, though, and that gave me access into the folder (I could do it in XP Home because of the Windows NT SP4 Security Configuration Manager). However, it appears some subfolders are still inaccessible. Two questions, then. Why exactly did this happen and how do I fix it?

  Read the article

• Linux does not communicate to Windows subinterface

  - by artaxerxe

  I set my NIC on Windows so that I have two interfaces: one (the first one) has IP 192.168.0.5 the other one has IP 10.10.10.1. On a Linux machine I set an interface to 10.10.10.2. On another Linux machine I set the interface to 10.10.10.3. And tried to ping those machines. Here is the result. Linux to Linux is ok. Windows to Linux also is ok. But Linux to Windows does not work. Can you help me on getting the communication between Linux and Windows? What should I do for this? I have to mention that those machines are connected through a switch. If you need any details, ask me please! Thanks in advance!

  Read the article

• Remote connection IP to use

  - by petwho

  I have two laptops that both run on ubuntu and installed ssh server and ssh client on them. One is usually on my desk at home and one I usually bring to my company. When I'm at home I can easily ssh to one from the other by typing this command (to login to the other laptop whose IP address is: 192.168.0.105) : ssh -p 22 [email protected] However, When I'm at my company, I try to type the same command and ofcourse it doesn't work. I understand that when at home I'm on LAN network, that my laptops actually using my ISP's address which differ from 192.168.0.107 asummed 203.113.131.1. So could you tell me what IP that ssh shoud use for my laptop (at work) to connet to my computer at home? Thank you.

  Read the article

• Postfix relay to multiple servers and multiple users

  - by Frankie

  I currently have postfix configured so that all users get relayed by the local machine with the exception of one user that gets relayed via gmail. To that extent I've added the following configuration: /etc/postfix/main.cf # default options to allow relay via gmail smtp_use_tls=yes smtp_sasl_auth_enable = yes smtp_tls_CAfile = /etc/ssl/certs/ca-bundle.crt smtp_sasl_security_options = noanonymous # map the relayhosts according to user sender_dependent_relayhost_maps = hash:/etc/postfix/relayhost_maps # keep a list of user and passwords smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd /etc/postfix/relayhost_maps user-one@localhost [smtp.gmail.com]:587 /etc/postfix/sasl_passwd [smtp.gmail.com]:587 [email protected]:user-one-pass-at-google I know I can map multiple users to multiple passwords using smtp_sasl_password_maps but that would mean that all relay would be done by gmail where I specifically want all relay to be done by the localhost with the exception of some users. Now I would like to have a user-two@localhost (etc) relay via google with their own respective passwords. Is that possible?

  Read the article

• Computer and internet use on a boat?

  - by dlamblin

  Let's assume that I seriously would like to be able to use my computer as easily and as carefreely while on a boat as I do while at home. In short, if I were on a boat for extended periods, such as two weeks at a time and occasionally over a few days out of port (this would be a 2 person sailing vessel), what would my options be for power, durability, and of course, internet access? I want more than just email, as I will likely keep doing a tad of development, and will be looking at google earth from time to time. I am already assuming that we're going with some kind of laptop, maybe even a macbook pro 12". I personally feel that netbooks are underpowered. And the last computer that I got a boat-friendly rating for was a ZX Spectrum, which was before the internet, and was likely due to it's 12vdc-happiness.

  Read the article

• NFS Client reports Permission Denied, Server reports Permission Granted

  - by VxJasonxV

  I have two RedHat 4 Servers. The client is 4.6, the server is 4.5. I'm attempting to mount a share from the server, onto the client via NFS. The /etc/exports configuration is as follows: /opt/data/config bkup(rw,no_root_squash,async) /opt/data/db bkup(rw,no_root_squash,async) exportfs returns these (among other) shares, nfs is running according to ps output. I've been attempting to use autofs on the client, but have opted to just mount the share manually considering the issues I'm having. So, I issue the mount request: mount dist:/opt/data/config /mnt/config mount: dist:/opt/data/config failed, reason given by server: Permission denied Ok, so let's see what the server has to say for itself. May 6 23:17:55 dist mountd[3782]: authenticated mount request from bkup:662 for /opt/data/config (/opt/data/config) It says it allowed the mount to take place. How can I diagnose why the client and server are disagreeing on the result?

  Read the article

• How do partitions help in optimizing the harddrive?

  - by Fasih Khatib

  I was recently reading a guide on Tom's Hardware about how to optimize the harddrive. They listed creating partitions as one of them. They said keeping the various files seperate is a good idea as it reduces the read/write cycles required. Now my querry is: what size partitions do i make for my 500gb harddrive. Its completely blank. I will be installing WIN7 in it. My usual strategy is to divide it into two equal partitions. Is it the optimum size?

  Read the article

• Clients didn't switch to secondary DNS server during fail over

  - by The Digital Ninja

  I have two internal dns servers set up and all my servers have both of them in the resolv.conf Our main dns server went down and suddenly no server could see each other. I edited a few of the servers resolv.conf manually and committed out the first (down) dns server and that machine would instantly be able to ping again. What did I do wrong, does it not auto switch to the secondary dns server when it times out? # File managed by puppet nameserver 192.168.146.100 nameserver 192.168.159.101 ;nameserver 72.14.188.5 domain example.com search example.com

  Read the article

< Previous Page | 726 727 728 729 730 731 732 733 734 735 736 737  | Next Page >