Search Results

Search found 20931 results on 838 pages for 'mysql insert'.

Page 733/838 | < Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740  | Next Page >

• Zabbix Proxy not collecting data

  - by syntaxcollector

  Hi All I have a working Zabbix 1.8.2 server collecting data for our office and our colo facility. However the link between the colo and office is flaky. What I'm trying to do is setup a proxy on the colo side to have a 1 hour cache and relay the data to our primary server at the office. Our zabbix server is compiled from source and uses a mysql database I've followed the instructions found in the zabbix documentation to compile the proxy using a sqlite3 database. I add the proxy to zabbix under Administration-DM-Proxies. The zabbix server "sees" the proxy because the "last seen" field is always under 60s. However when I assign a colo host to the proxy I stop receiving data from it. The colo host's zabbix_agentd.log file says this: 29343:20100622:124847 Timeout while answering request 29343:20100622:124847 Getting list of active checks failed. Will retry after 60 seconds The zabbix_proxy.log says this. 2041:20100622:123131.760 Deleted 0 records from history [0.000994 seconds] 2028:20100622:124131.671 Error while receiving answer from server [ZBX_TCP_READ() failed I also am unable to receive any SNMP data which is more important to me than the zabbix agent data. Has anyone had this problem before? Zabbix Server OS: CentOS5.4 Zabbix Server Build: 1.8.2 from source Zabbix Proxy OS: CentOS5.4 Zabbix Proxy Build: 1.8.2 from source P.S. The SQLite database on the zabbix proxy never gets any data written to it, it is identical to when I created it from the blank schema in zabbix-1.8.2/create/schema. (Yes I've checked the permissions)

  Read the article

• Apache process consuming all memory on the server

  - by jemmille

  I have an apache process that suddenly appears on a particular server. When it shows up it starts consuming memory at a very rapid rate, then moves on to all the swap. In all it consumes about 11GB (including swap) of memory and the server eventually becomes unresponsive. The load on the server is under 1 at all other times. The process runs as nobody and I am having a hard time tracking down the source. If i run an strace on the process and all it did was continuously dump out mprotect over and over again If i run lsof -p <pid>, I get this, but only sometimes: httpd 19229 nobody 152u IPv4 175050 crawl-66-249-67-216.googlebot.com:62336 (CLOSE_WAIT) httpd 19229 nobody 153u IPv4 179104 crawl-66-249-71-167.googlebot.com:58012 (ESTABLISHED) As long as I catch it, I can kill the process and the server almost immediately stabilizes. I have on site on the server that is getting a few thousand hits a a day that I think might be the source, but I still can't find the exact reason. Also, this is a cPanel server and I have upcp'd the server, rebuilt apache with easy apache, and rebuilt httpd.conf. It is not spawing any related processes, meaning I can find any php, mysql, cgi, etc. processes that relate to this process. It's just a loner process that balloons fast and consumes ever last MB of memory. This is on a XenServer 5.6 based VM. No other servers in the cluster are having this issue.

  Read the article

• Advice needed: warm backup solution for SQL Server 2008 Express?

  - by Mikey Cee

  What are my options for achieving a warm backup server for a SQL Server Express instance running a single database? Sitting beside my production SQL Server 2008 Express box I have a second physical box currently doing nothing. I want to use this second box as a warm backup server by somehow replicating my production database in near real time (a little bit of data loss is acceptable). The database is very small and resources are utilized very lightly. In the case that the production server dies, I would manually reconfigure my application to point to the backup server instead. Although Express doesn't support log shipping natively, I am thinking that I could manually script a poor man's version of it, where I use batch files to take the logs and copy them across the network and apply them to the second server at 5 minute intervals. Does anyone have any advice on whether this is technically achievable, or if there is a better way to do what I am trying to do? Note that I want to avoid having to pay for the full version of SQL Server and configure mirroring as I think it is an overkill for this application. I understand that other DB platforms may present suitable options (eg. a MySQL Cluster), but for the purposes of this discussion, let's assume we have to stick to SQL Server.

  Read the article

• Tomcat performing terribly for no apparent reason

  - by John

  We're running a game application .WAR on Tomcat 6 on an Amazon EC2 server, 8 core processor, 7gb RAM. The application uses a MySQL database hosted on Amazon RDS. This Facebook application takes ages to access when a mere 20-30 users are playing it. Big difference from 1-2 users. The entire .WAR is ~4mb, all static content hosted elsewhere. The server has never been close to running out of RAM. The CPU utilization has never been higher than 13.5-14%. Even with ~500 users that completely slowed everything to a standstill. The thread count or threadpools isn't close to being maxed out. I heightened maxthreads but it didn't make a noticeable difference. My theory is that Tomcat can only use one processor core, which would explain why it was slowed to a halt even though CPU usage was stably at 13-14% at the activity spike. But I'm struggling to understand why it would only use one CPU core. There is no processor cap in server.xml. The app contains several servlets (4 or 5). There is no mention of SingleThreadModel in the Java code. WHAT could be causing the application to run extremely slowly? If there is only 1-5 people on the application it runs fine. With 20-30 people it's barely contactable.

  Read the article

• Multiple PHP SAPI configuration

  - by DTest

  I'm trying to build PHP for use as an apache shared module --with-apxs2 but also with the 'php-cgi' binary (fastcgi) on Mac OSX 10.6. I'm using this ./configure : /configure --prefix=/usr/local/PHP \ --with-apxs2=/usr/local/apache/bin/apxs \ --disable-ipv6 \ --enable-cgi \ --with-curl \ --with-mysqli=/usr/local/mysql/bin/mysql_config \ --with-openssl=/usr \ --enable-ftp \ --enable-shared \ --enable-soap \ --enable-sockets \ --enable-zip \ --with-zlib-dir It builds the apache php5.so module just fine, but in /usr/local/PHP/bin, there is no php-cgi file. If I build it without the --with-apxs2 option (and indeed, I don't even need the --enable-cgi option) the php-cgi file gets built with no problems. Background on my setup: PHP 5.3.4, Apache 2.2.14, Mac OSX 10.6, Tomcat with JavaBridge (which is why I need the php-cgi file) Without the apxs2 option, /usr/local/php/bin/php -v produces: PHP 5.3.4 (cli) (built: Dec 21 2010 21:35:14) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies and /usr/local/php/bin/php-cgi -v produces: PHP 5.3.4 (cgi-fcgi) (built: Dec 21 2010 21:35:12) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies My question is, what am I not understanding with php SAPIs that won't allow the building of the two modules at the same time? Also, can I build it --with-apxs2 the first time, then make clean and rebuild in the same PHP directory /usr/local/php for the php files without issue?

  Read the article

• How can I debug user mode driver failures in Windows 8

  - by Tom

  I have a 32 GB SD Card. Whenever I insert this card in to my newly upgraded Windows 8 laptop the OS stops responding normally. Metro Apps won't work. The system may or may not log in. Desktop apps may or may not be able to do things. When I remove the card and restart then all is fine. As soon as I put the card back in, the system starts misbehaving again. I've run Windows Update, so I have the latest drivers from Microsoft. This does not occur with the 8 GB cards I have. Unfortunately I only have one 32 GB card, so I can't test with others. From examining the system event log I've determined this is happening due to a user mode driver failure. How can I best debug this issue from here? How can I figure out which driver this is related to? Will there be a Dr. Watson crash dump somewhere? Details - System - Provider [ Name] Microsoft-Windows-DriverFrameworks-UserMode [ Guid] {2E35AAEB-857F-4BEB-A418-2E6C0E54D988} EventID 10110 Version 1 Level 1 Task 64 Opcode 0 Keywords 0x2000000000000000 - TimeCreated [ SystemTime] 2012-10-29T00:51:57.532718300Z EventRecordID 40417 Correlation - Execution [ ProcessID] 1056 [ ThreadID] 3796 Channel System Computer thebrain - Security [ UserID] S-1-5-18 - UserData - UMDFHostProblem [ lifetime] {811E3DC4-FBC6-420B-ABCC-AD7505A36F3B} - Problem [ code] 3 [ detectedBy] 2 ExitCode 3 - Operation [ code] 259 Message 72448 Status 4294967295 Edit 1 So I tried using Debug View from SysInternals (you can get it here: http://technet.microsoft.com/en-us/sysinternals/bb896647.aspx). That gave me this information: which is not especially helpful. Then I tried connecting WinDbg to WUDFHost.exe (the process that seems to host user mode drivers) to see if it could catch the error. Get it here: http://msdn.microsoft.com/en-US/windows/hardware/hh852363 Instructions: http://msdn.microsoft.com/en-US/library/windows/hardware/ff554716(v=vs.85).aspx That didn't help much. It didn't catch any exceptions as I'd hoped (which would point me to the cause of the crash at least). Here's the stack of one of the threads:

  Read the article

• How to install RMagick RubyGem on Mac OS X 10.6 Snow Leopard?

  - by misbehavens

  I am getting this error while trying to install RMagick: $ sudo gem install rmagick Building native extensions. This could take a while... ERROR: Error installing rmagick: ERROR: Failed to build gem native extension. /System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/bin/ruby extconf.rb checking for Ruby version >= 1.8.5... yes checking for gcc... yes checking for Magick-config... no Can't install RMagick 2.13.1. Can't find Magick-config in /usr/bin:/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/X11/bin:/opt/local/bin:/usr/local/git/bin:~/bin:/usr/local/bin:/usr/local/mysql/bin:/usr/local/pear/bin *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/bin/ruby Gem files will remain installed in /Library/Ruby/Gems/1.8/gems/rmagick-2.13.1 for inspection. Results logged to /Library/Ruby/Gems/1.8/gems/rmagick-2.13.1/ext/RMagick/gem_make.out How can I install the RMagick RubyGem on Snow Leopard?

  Read the article

• How to transfer Windows Vista disk image to new machine

  - by Mike Hobbs

  I'm trying to upgrade a user's machine to some better hardware. I know of Easy Transfer, but I'd rather not have to reinstall all the programs that are already present. (Some of which are no longer available, anyway). Instead, I'm trying to transfer the entire disk image from one machine to the other, but I ran into issues. If I copy the partition image over to the new machine using Clonezilla, I get errors on boot saying that I need to insert the Vista install disk and run repair. I do that, but it then says that it is unable to repair whatever it is that's broken. Next, I tried to sysprep the old machine before creating the image, but sysprep fails saying that it encountered some sort of system error. Should it be possible to sysprep any arbitrary machine, or does it only work on a relatively clean install? Could it be a missing driver that is tripping me up? The new machine is a fairly stock desktop that shouldn't need any special drivers beyond what's already present in standard Vista. Are there any foolproof methods for doing this sort of thing?

  Read the article

• Ctrl + 1 and Ctrl + 2 key combinations don't work

  - by musicfreak

  I noticed back in August (when I got StarCraft 2) that the key combinations Ctrl + 1 and Ctrl + 2 didn't work. I thought this was weird because Ctrl + 3 and all the other combinations worked fine (including Shift + 1, etc), so I didn't think much of it; I just shrugged it off as a SC2 bug. Now, 4 months later, I decided to play a completely unrelated game--Dawn of War 2--and noticed the same thing: those two specific key combinations don't work. To make sure I wasn't going insane, I tried it in Chrome and a couple other applications, and alas, it didn't work. I remember playing strategy games over the summer before StarCraft 2 and it worked fine. Any idea as to what went wrong? My keyboard, a Microsoft Wireless Keyboard 1000 (I know, insert Microsoft joke here), is a little over a year old, so I'm going to assume it's not dying until proven otherwise. Things I've tried ActiveHotkeys says the key combination is not a global hotkey. Tried another keyboard--still doesn't work. The key combinations do work in a virtual machine (tried with both Windows and Ubuntu as guests).

  Read the article

• Web hosting for multiple web sites providing system isolation

  - by Justin

  We have a small number of projects where we expect the client will not be maintaining the installed versions of applications we install to power the site (such as Drupal). Given that an important part of security is keeping things updated, we don't want to host these projects on our Plesk-powered dedicated servers that currently host lots of our other client's websites. Our goal is to find a host where we can deploy isolated instances (be these slices, virtual servers, grid servers, etc) for each individual (or groups of 2-3) web sites as we need them. These instances would be completely separate, so that if one web site were hacked it would not impact any other site. Typical hosting requirements: Linux Apache PHP 5 MySQL Supports Drupal Ability to setup a cron task (but we don't need SSH access) Daily backups Virtualized/cloud hosting (we want to avoid shared) Pricing per site is around $25/month OS is patched automatically Some options we have considered but won't work: MediaTemple: Two major data center-wide security incidents and recent downtime foster doubt about this host's technical ability. Slicehost: This would require us to manage the entire server, which we don't want to do. Rackspace Cloud Sites (formerly Mosso): No backup options. Do you have any recommended hosting options for given these requirements?

  Read the article

• VPN being blocked somewhere between either my BT2700HGV and DLink DFL-210

  - by Dom

  Hi, For some time I have been unable to get VPN working through my set up. I have a BT2700HGV Router (2 Wire Model) and as a firewall I have the Dlink DFL-210. You can't turn the firewall completely off on the BT2700HGV so I have it set to DMZplus mode for the Firewall. In theory this should then allow the VPN ports through. On the Firewall I have a series of rules set up and one is the pptp-allow rule which should allow access on the correct ports also. When I try to connect via VPN however the client machine gets an error 809. If I check the log on the Dlink firewall, I see this record: http://dl.dropbox.com/u/1041315/packetdrop.PNG The laptop I am testing the vpn with is connected directly to the BT2700HGV router and I am trying to VPN from it onto 81.138.86.217. I can't work out whether I have some sort of problem in the set up of the rules on my firewall or if the BT router (even though it's in DMZplus mode) is still blocking port 1723. I read somewhere that there where problems because BTs Openzone held onto this port for some reason. Any help would be greatly appreciated. If you need further screen shots or information then please let me know. I wasn't able to create new tags for the router and firewall name or insert the picture in as I am new to the forum. Dom :-)

  Read the article

• SSH client and Command Prompt replacements Windows look-and-feel

  - by Oddthinking

  The Problem I've worked exclusively in Windows. I can handle that. I've worked exclusively in DOS (a long time ago!). I can handle that. I've worked exclusively in Unix. I can handle that. Right now, I am developing a command-line (python) application on a Windows machine, testing it in a DOS box (i.e. Windows' Command prompt), and then deploying it to Linux, and running it with PuTTY. I cannot handle that. My productivity drops dramatically when CTRL-C cuts in one window (Windows) and kills the process in another (DOS, Linux). My productivity drops dramatically when Enter copies the selection in one window (DOS), and deletes the selection in another (Windows), and runs the current half-edited command in the third (PuTTY). My productivity drops dramatically when I cannot hit Undo, Home or End. The Solution I am Seeking An SSH/Bash command-line client that runs on Windows and, to the extent possible, uses all the standard Windows shortcuts (Cut, Copy, Paste, Undo, Home, End, Insert, Shift-Arrows, etc.) work on a bash command line. Bonus points if it puts the cursor between letters, rather than on them. Plus, an equivalent DOS command-line drop-in that runs on Windows, and provides the same interface. I appreciate there may need to be special buttons to actually transfer CTRL codes (like CTRL-C) through in the cases I need them. I suspect the SSH client will need to be specific to a shell (so it knows when it is at the command prompt, and when it is inside a running app.) I know there are many SSH clients, but I am looking for advice for a particular need. PuTTY feels like an escape route for Unix programmers stuck on Windows. I am the opposite. Can anyone recommend one (or maybe a combination of an SSH client and an Command-Line replacement)?

  Read the article

• Identifying and Resolving Oracle ITL Deadlock

  - by Allan

  I have an Oracle DB package that is routinely causing what I believe is an ITL (Interested Transaction List) deadlock. The relevant portion of a trace file is below. Deadlock graph: ---------Blocker(s)-------- ---------Waiter(s)--------- Resource Name process session holds waits process session holds waits TM-0000cb52-00000000 22 131 S 23 143 SS TM-0000ceec-00000000 23 143 SX 32 138 SX SSX TM-0000cb52-00000000 30 138 SX 22 131 S session 131: DID 0001-0016-00000D1C session 143: DID 0001-0017-000055D5 session 143: DID 0001-0017-000055D5 session 138: DID 0001-001E-000067A0 session 138: DID 0001-001E-000067A0 session 131: DID 0001-0016-00000D1C Rows waited on: Session 143: no row Session 138: no row Session 131: no row There are no bit-map indexes on this table, so that's not the cause. As far as I can tell, the lack of "Rows waited on" plus the "S" in the Waiter waits column likely indicates that this is an ITL deadlock. Also, the table is written to quite often (roughly 8 insert or updates concurrently, as often as 240 times a minute), so and ITL deadlock seems like a strong possibility. I've increased the INITRANS parameter of the table and it's indexes to 100 and increased the PCT_FREE on the table from 10 to 20 (then rebuilt the indexes), but the deadlocks are still occurring. The deadlock seems to happen most often during an update, but that could just be a coincidence, as I've only traced it a couple of times. My questions are two-fold: 1) Is this actually an ITL deadlock? 2) If it is an ITL deadlock, what else can be done to avoid it? Cross-posted from Stack Overflow. Deadlocks are normally a programming problem, but ITL deadlocks relate directly to how Oracle writes to disk, so this may be an area where DBAs have more experience.

  Read the article

• Find out the type of an automounted device

  - by Steve Bennett

  I'm working on a system (Ubuntu Precise) with a mount defined in /etc/fstab as follows: /dev/vdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 Originally I just wanted to find out if it's NFS (due to potential MySQL locking issues). Judging from man mount, it's not: If no -t option is given, or if the auto type is specified, mount will try to guess the desired type. Mount uses the blkid library for guessing the filesystem type; if that does not turn up anything that looks familiar, mount will try to read the file /etc/filesystems, or, if that does not exist, /proc/filesystems. All of the filesystem types listed there will be tried, except for those that are labeled "nodev" (e.g., devpts, proc and nfs). If /etc/filesystems ends in a line with a single * only, mount will read /proc/filesystems afterwards. But, out of curiosity now, how can I find out more about what type of device it actually is? (For context, this is a VM running on OpenStack. The device is a 60Gb allocation mounted from somewhere - but I don't know how.)` EDIT Including answers here: $ mount /dev/vdb on /mnt type ext3 (rw,_netdev) $ df -T /dev/vdb ext3 61927420 2936068 55845624 5% /mnt

  Read the article

• Dropped connections between Linux Servers in Data Center

  - by Emil H

  I have a number of linux servers at a us-based datacenter. The servers were installed by the hosting company, and are running fedora core. We're experiencing problems with dropped connections. The issue seems to be that when we attempt to connect to one of the other servers after a period of inactivity, the first connection attempt will fail, and sometimes the second. However, after that the connection succeds and it works for a while. This happens for both mysql connections and raw socket connections, but only seems to occur when connecting to some of our servers. The confusing part is that it some of the servers for which we see different behaviors have identical hardware configuration and software. For example, it happens when connecting to a server called mysql2, but not for a server called mysql3. These servers were installed at the same time, but the same specifications. The problem can be reproduced somewhat reliably, but only after waiting fifteen minutes to half an hour. This makes it hard to diagnose, and even harder since I'm not really sure what to look for. I realize that connections sometimes failed, and that we should write our applications to compensate for this but these servers all in the same data center. Why would it matter if two servers haven't communicated for a while? Does anybody have an idea what might be causing this? Is it a server configuration problem or a network problem that I should contact the hosting company about. What do I tell them to look for? Unfortunately our experience has been that the support staff doesn't investigate problems in depth unless we give them detailed directions.

  Read the article

• Webserver optimization

  - by f-aminov

  Hi guys! I have a website hosted on a VPS (512Mb - minimum guranteed memory, 510Mhz proccessor, Debian 5.0 Lenny, Apache 2.2.9 with nginx 0.7.65 as a frontend to serve static content, MySQL 5.1.44, PHP 5.3.2 with APC caching). I'm a web developer, so I'm not very good at optimizing servers, but I've managed to install and setup all those neccessary components (LAMP, nginx, etc.). After that I decided to stress test my website (which uses Drupal 6.16 with caching and all possible optimization enabled) using a utility called "Webserver Stress Tool 7". And it seems to me that the results aren't any good - here is a graph (sorry, as a new user I'm not allowed to post images) As you can see the response time depending on amount of simultaneous users increases very quickly. With 10 simultaneous users the time is about 1000ms, with 100 simultaneous users it's about 15000ms (15s!). The question is do you think this is normal behavior for such a server or something is wrong with the settings and optimization? If you think something is wrong what particulary could be wrong? Any other suggestion how to speed this a little bit up?

  Read the article

• Error in Bind9 named.conf file. Bind won't start.

  - by tj111

  I'm trying to setup a DNS server on an Ubuntu Server machine (10.04). I configured an entry in named.conf.local to test it, but when trying to restart bind9 I get the following error: * Starting domain name service... bind9 [fail] So I checked the output of syslog and this is what I get. May 20 18:11:13 empression-server1 named[4700]: starting BIND 9.7.0-P1 -u bind May 20 18:11:13 empression-server1 named[4700]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' May 20 18:11:13 empression-server1 named[4700]: adjusted limit on open files from 1024 to 1048576 May 20 18:11:13 empression-server1 named[4700]: found 4 CPUs, using 4 worker threads May 20 18:11:13 empression-server1 named[4700]: using up to 4096 sockets May 20 18:11:13 empression-server1 named[4700]: loading configuration from '/etc/bind/named.conf' May 20 18:11:13 empression-server1 named[4700]: /etc/bind/named.conf:10: missing ';' before 'include' May 20 18:11:13 empression-server1 named[4700]: loading configuration: failure May 20 18:11:13 empression-server1 named[4700]: exiting (due to fatal error) So it thinks I have an error in the default named.conf file, which is pretty ridiculous. I went through it and deleted a blank line just for the hell of it, but I can't see how it figures there's an error in there. Note that before this I did have an error in named.conf.local, but it showed up properly in syslog and I fixed it, so it is reporting the correct file. Here is the contents of named.conf: // This is the primary configuration file for the BIND DNS server named. // // Please read /usr/share/doc/bind9/README.Debian.gz for information on the // structure of BIND configuration files in Debian, *BEFORE* you customize // this configuration file. // // If you are just adding zones, please do that in /etc/bind/named.conf.local include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones";

  Read the article

• IIS 7.5 error 500 in fastcgi module after upgrading wordpress to 3.0.2

  - by Maniac13

  I am running multiple wordpress blogs on the following setup: Server 2008 R2; IIS 7.5; PHP 5.3.3; MySQL 5.0.7; I upgraded my wordpress install from 2.9.2 to 3.0.2 (on 2 different sites) today and the upgrade went fine. I can serve .php pages without errors, log into the admin system etc. I can browse my blog by going directly to mywebsite.com/index.php, but when I try to go to mywebsite.com (without the index.php) I get he below 500 error. I reset IIS, removed and re-attached the default document, but I am running out of ideas. Please if anyone has a solution for this that would be great. This is the 500 error I am getting: Error Summary HTTP Error 500.0 - Internal Server Error The page cannot be displayed because an internal server error has occurred. Detailed Error Information Module FastCgiModule Notification ExecuteRequestHandler Handler PHP FastCGI Error Code 0x00000000 Requested URL http://mywebsite.com:80/index.php Physical Path D:\mywebsite.com\index.php Logon Method Anonymous Logon User Anonymous Thanks Stephan

  Read the article

• Need help diagnosing my machine

  - by Tom Collins

  I have something that just slows my computer to a crawl sometimes. Not running anything big. Yesterday all I had running (besides background apps) were Firefox & Windows Explorer and could barely even switch screens. Nothing showing up in the task manager as hogging CPUs. I have all non-essential services stopped (MySQl & MSSQL) unless I need them. I made some restore points not long ago, but they disappeared. This is a development mach with a LOT of apps installed, so I really, really do not want to re-install Windows. So, what I'm looking for are ideas or tools I can use to help diagnose this problem. The only clues I have is this started right after I installed Office 2013 (with Office 2010 still installed as well) installed Visual Studio 2012 (also keeping 2010 as a co-install) and installed MSSQL 2012 (upgrade from 2008, no co-install) Also, computer runs fine in Safe Mode. I've just ran out of ideas of what to check. Any help / suggestions would much appreciated. Thanks P.S. I'm running Win 7 Pro (x64). Office is also 64 bit. Visual Studio & MSSQL are 64 bit if that option was available (not sure).

  Read the article

• fedora apache/nginx pylons

  - by microchasm

  I'm trying to wrap my head around Pylons and how it works. So far... it's been confusing... I'm using EC2 with Fedora8. Everything is working so far (i.e. I have Pylons/python et al installed and after creating a test app and running paster serve I can access the default page via my domain name). As the Pylons docs explain and as I understand, the built in paster serve server is not suited for a production environment. What I am not clear on, then, is what to do next... It seems like nginx is a good option, but I am more familiar with Apache (like .0002%). I plan on having virtualhosts (which nginx says can accomodate). However, I am totally unclear on how the big picture is supposed to work. In order to serve an app, does paster serve need to be running? Does then nginx/apache basically just act as a proxy to shuttle connections to the paster server? How do I start it so it doesn't terminate after closing the ssh connection? If running multiple apps, what do I set as the host/port in development.ini to differentiate the apps? Or if this is not the right way, how do I differentiate beween apps? I am more familiar with MySQL, but willing to negotiate PostgreSQL if it's a better fit. Is it? Is virtualenv a prerequisite to running multiple apps on the same machine? Thanks in advance for any tips.

  Read the article

• Why is Xampp unable to start Apache?

  - by jribeiro

  I formatted my computer a week ago. Installed wampp on Windows XP, git and everything I needed. When I run git for the first time it told me it had a problem with my user folder (because of the accents) so I created a new user and migrated everything to the new one. After this, wampp wouldn't start anymore. I uninstalled it and installed xampp which is what I'm using now. My problem is that even though I requesed xampp to install Apache as a service it isn't installed. It doesn't show in Windows' services screen. Xampp control panel shows mysql service running OK. When I click to install Apache as a service it returns no error. When I click Start Apache no error is outputed. No file and no errors under c:/xampp/apache/log/ If I restart my computer it says that Apache service is not installed. I tried to reinstall wampp and the same problem occurs. If I run netstat -a -no nothing is running on port 80! What can I do?

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• Enable Soap for PHP 5.5.x on CentOS 6.5

  - by Chris Mancini

  Unfortunately I have to support soap on my server for the Fedex webservice. I recompiled PHP enabling support and it works via CLI but not PHP-fpm. They both point to the same ini file and both show the module loaded, but only CLI shows the configuration values. Output of php -i | grep -i soap Configuration File (php.ini) Path => /usr/local/etc Loaded Configuration File => /usr/local/etc/php.ini Configure Command => './configure' '--prefix=/usr/local' '--with-config-file-path=/usr/local/etc' '--with-config-file-scan-dir=/usr/local/etc/php_user/' '--enable-fpm' '--enable-ftp' '--enable-libxml' '--enable-mbstring' '--enable-pdo' '--enable-soap' '--enable-sockets=shared' '--enable-zip' '--with-curl' '--with-fpm-group=nginx' '--with-fpm-user=nginx' '--with-freetype-dir=/usr/lib64/' '--with-gd' '--with-jpeg-dir=/usr/lib64/' '--with-libdir=lib64' '--with-mcrypt' '--with-openssl' '--with-pdo-mysql' '--with-pear' '--with-readline' '--with-tidy' '--with-xsl' '--with-zlib' '--without-pdo-sqlite' '--without-sqlite3' soap Soap Client => enabled Soap Server => enabled soap.wsdl_cache => 1 => 1 soap.wsdl_cache_dir => /tmp => /tmp soap.wsdl_cache_enabled => 1 => 1 soap.wsdl_cache_limit => 5 => 5 soap.wsdl_cache_ttl => 86400 => 86400 Output from php-fpm phpinfo(): Configuration File (php.ini) Path /usr/local/etc Loaded Configuration File /usr/local/etc/php.ini SOAP Brad Lafountain, Shane Caraveo, Dmitry Stogov Please help, I have tried so many things...

  Read the article

• Exchange 2003: Unrestrict send mail size for specific users / groups?

  - by Kip

  Good (insert appropriate time of day here) SF folks, I have the following situation; We have a message size limit for sending set at 20mb in Global Settings | Message Delivery. We have a limit of 50mb set at an external 3rd party spam vendor. I need to enable some users to be able to send messages that are upwards of around 40mb in size. However, when I set the Sending Message Size Maximum to 50mb within the delivery restrictions of a users exchange properties, it would appear that this does not win. It seems that the lowest value wins for this situation. I need to be able to allow certain users to send messages larger than the 20mb limit, but to have everyone else have the 20mb limit in place. How can I do this? The only way I could see was to raise the limit set in Global Settings | Message Delivery to 50mb and then set everyone elses (bar the people who need increased limit) delivery restrictions max size down. But I cannot see an easy way to do the last bit hence my post here looking for advice. There are valid reasons we need to send mail this size and whilst we are putting together other mechanisms for delivery this data, we still need to get this put in place. Thanks in advance Kip

  Read the article

• Why would the SQL 2008 "Generate scripts..." utility generate an invalid SQL script?

  - by Deane

  I have a SQL2008 database that needs to be restored to a SQL2005 instance. I have gone through the "Generate scripts..." wizard, set it for SQL2005 compatibility, and generated a 62MB SQL script. When I run it on the SQL2005 instance, it throws all kinds of errors, and some of them are really strange in that they describe an invalid database. FK constraints are wrong. It's trying to create FKs on columns that don't exist. It's trying insert records with duplicate key errors. It's trying to create the same objects twice. Any idea how this could happen? This SQL script was generated by SQL Server Management Studio just minutes before I tried to restore it, and was not modified. Why would this generate an invalid SQL file? Doesn't it just describe the SQL2008 database, which is presumably valid since we're using it? In particular, the duplicate key insertion errors mystify me. If there's a key constraint in the SQL script, then there must be the same thing in the SQL2008 table. So how could we get rows in there that violate that key constraint?

  Read the article

< Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740  | Next Page >