Search Results

Search found 41582 results on 1664 pages for 'fault tolerance'.

Page 74/1664 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

• MDaemon vs Exchange (2007-2010). Which one should we choose ?

  - by Deniz

  We are at the verge of a mail server decision. We do currently use 2 mail servers : MDaemon 10 and Exchange 2003. We are planning to use a company and customer wide one point solution. Our main candidates are MDaemon 11 and Exchange 2007 or 2010. We would like to learn other users experiences on those solutions. The server-side experiences, the user-side experiences, feature set, TCO, support options etc. And if there were other solutions (like MDaemon 11 + Exchange or anything else) what would you suggest ?

  Read the article

• Windows 2003 Domain Controller Very Upset about NIC Teaming

  - by Kyle Brandt

  I set up BACS (Broadcom Teaming) to team two NIC on a Windows 2003 Active Directory Domain Controller. Networking still works okay, I can ping the gateway etc, but both DNS and Active Directory fail to start with various 40xx errors. The team that I created is Smart load Balancing with Failover, with one backup and only one in smart load balancing (So really it is just failover). I have the team the same IP address that the single active NIC had before. Anyone seen this before, or have any ideas what the problem might be? Event Type: Error Event Source: DNS Event Category: None Event ID: 4015 Date: 3/7/2010 Time: 10:33:03 AM User: N/A Computer: ADC Description: The DNS server has encountered a critical error from the Active Directory. Check that the Active Directory is functioning properly. The extended error debug information (which may be empty) is "". The event data contains the error. Event Type: Error Event Source: DNS Event Category: None Event ID: 4004 Date: 3/7/2010 Time: 10:33:03 AM User: N/A Computer: ADC Description: The DNS server was unable to complete directory service enumeration of zone .. This DNS server is configured to use information obtained from Active Directory for this zone and is unable to load the zone without it. Check that the Active Directory is functioning properly and repeat enumeration of the zone. The extended error debug information (which may be empty) is "". The event data contains the error. Event Type: Error Event Source: NTDS Replication Event Category: DS RPC Client Event ID: 2087 Date: 3/7/2010 Time: 10:40:28 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: ADC Description: Active Directory could not resolve the following DNS host name of the source domain controller to an IP address. This error prevents additions, deletions and changes in Active Directory from replicating between one or more domain controllers in the forest. Security groups, group policy, users and computers and their passwords will be inconsistent between domain controllers until this error is resolved, potentially affecting logon authentication and access to network resources.

  Read the article

• ESXI Crash need help to understand log and support about nexentastor on virtual machine

  - by Bgnt44

  If i understand right, the following core dump means that the cpu4 has crashed the Host if i read the next line it seem that at the time the CPU 4 was assigned to the NexentaStore Vm ... SO if im right i can say that NexentaStor Vm crash my esxi Am i right ? Does that core dump can provide me some more informations ? 2012-11-14T03:48:01.046Z cpu4:6089)0x41221f25ba08:[0x41803007abff]PanicvPanicInt@vmkernel#nover+0x56 stack: 0x3000000008, 0x41221f25ba 2012-11-14T03:48:01.046Z cpu4:6089)0x41221f25bae8:[0x41803007b4a7]Panic@vmkernel#nover+0xae stack: 0x2e067c00000010, 0x0, 0x1f25bb38, 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25bc18:[0x4180300a7823]TLBDoInvalidate@vmkernel#nover+0x45a stack: 0xca, 0x0, 0x0, 0x0, 0x0 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25bc68:[0x418030489e17]UserMem_CartelFlush@<None>#<None>+0xce stack: 0xcaa0b, 0x0, 0x0, 0x4 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25bd78:[0x41803048ab91]UserMemUnmapStateCleanup@<None>#<None>+0x58 stack: 0x0, 0x41221f25bd 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25be58:[0x41803048b97d]UserMemUnmap@<None>#<None>+0x104 stack: 0x41221f267000, 0x41221f25bf 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25be98:[0x41803048bf20]UserMem_Unmap@<None>#<None>+0xe3 stack: 0x426, 0x0, 0x41221f25bef8, 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25beb8:[0x4180304a5985]UW64VMKSyscallUnpackReleasePhysMemMap@<None>#<None>+0x18 stack: 0x10 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25bef8:[0x418030476791]User_LinuxSyscallHandler@<None>#<None>+0x17c stack: 0x41803004cc70, 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25bf18:[0x4180300a82be]User_LinuxSyscallHandler@vmkernel#nover+0x19 stack: 0x3ffe63bed80, 0 2012-11-14T03:48:01.049Z cpu4:6089)0x41221f25bf28:[0x418030110064]gate_entry@vmkernel#nover+0x63 stack: 0x10b, 0x0, 0x0, 0x426, 0xcf76 2012-11-14T03:48:01.049Z cpu4:6089)VMware ESXi 5.1.0 [Releasebuild-799733 x86_64] PCPU 1 locked up. Failed to ack TLB invalidate (total of 1 locked up, PCPU(s): 1). 2012-11-14T03:48:01.050Z cpu4:6089)cr0=0x80010031 cr2=0xcaa0b750 cr3=0x197d7b000 cr4=0x42768 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:0 world:6111 name:"vmm0:Windows_2012_-_SQL" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:1 world:6032 name:"vmm0:Windows_2012_-_AD" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:2 world:6098 name:"vmm0:Windows_2012_-_App" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:3 world:4099 name:"idle3" (IS) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:4 world:6089 name:"vmx-vcpu-0:NexentaStor" (U) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:5 world:6134 name:"vmm0:Ubuntu_-_NGINX" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:6 world:4102 name:"idle6" (IS) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:7 world:4103 name:"idle7" (IS) 2012-11-14T03:48:01.050Z cpu4:6089)@BlueScreen: PCPU 1 locked up. Failed to ack TLB invalidate (total of 1 locked up, PCPU(s): 1).

  Read the article

• Why does tracerpt use up all of my Sql Server's memory?

  - by Cypher

  We have a MS Sql Server 2008 machine with 12 GB of RAM... twice now within the last week this server was knocked on its backside by a process called "tracerpt.exe" which was found to have taken up ALL of the system's memory and leaving nothing for sqlserver. Done my homework, figured out what this program is... but still no idea why it's hogging up so much RAM (though I have an idea), nor what application is actually executing it. This server is the back-end to a Microsoft Dynamics CRM 4.0 application which is hosted on a separate server and is our production database used for just about everything. If this program is necessary, I would like to be able to find the application that is executing this thing and remove it or disable whatever feature is causing this quite annoying occurrence. Any ideas?

  Read the article

• Add Scheduled Task to reset search indexes for Exchange 2007

  - by Samosa

  I simply want to run a ResetSearchIndex -force on a schedule. What is the correct usage for the command in the Scheduled Task properties? It seems I would first need to start Powershell, then load the console file or snap-in for Exchange, which one of these is the closest: C:\WINDOWS\system32\WINDOW~2\v1.0\POWERS~1.EXE -"D:\Program Files\Microsoft\Exchange Server\Scripts" ResetSearchIndex.ps1 -force dbname or C:\WINDOWS\system32\WINDOW~2\v1.0\POWERS~1.EXE -PSConsoleFile "D:\Program Files\Microsoft\Exchange Server\bin\exshell.psc1" -noexit -command ".'D:\Program Files\Microsoft\Exchange Server\Scripts' ResetSearchIndex.ps1 -force dbname or C:\WINDOWS\system32\WINDOW~2\v1.0\POWERS~1.EXE -PSConsoleFile "D:\Program Files\Microsoft\Exchange Server\bin\exshell.psc1" -noexit -command ".'D:\Program Files\Microsoft\Exchange Server\Scripts\ResetSearchIndex.ps1' -force dbname

  Read the article

• Problems connecting to MS Dynamics AX 2009 Application Object Server

  - by Sam

  I've got a funny problem connecting to an AOS server. I got a domain network containing a (VM) Server running the Application Object Server (AOS). Client computer A) can connect to the AOS without problems and work. When client computer B) tries to connect, all I get is this error message: Logon Error Connection with the Application Object Server could not be established. The event log of Client B) does not contain any messages about this. Firewalls are off on all three computers (by GP). Tcp/ip from cliebt B) to the AOS server does run fine. Both clients run the same OS (win 7 RC), sit on the same subnet, next to each other. Yesterday it all worked, today just one computer can connect. Any ideas what might cause this problem, how to resolve it, or how to debug it?

  Read the article

• Fatal error 9001 on shared SQL Server 2008

  - by user643192

  I've asked this same question on StackOverflow, but I might actually have a better chance for an answer here so am posting here as well. I know this question has been asked here before, but none of the suggestions have worked for me. I have an ASP.NET MVC (v. 3) website on a shared server. The website was working fine for a few weeks now, until I started getting a Fatal Error 9001 error straight after login. Because this is a shared server, there are only very limited things I can do with the database (and I don't know that much about databases anyway). The help desk insist that there is nothing wrong with their server. I got various suggestions from them: Upgrading to the business plan because I am out of space (first suggestion) Even though the .mdb file is small, the .ldb can grow very quickly. The .ldb file is probably taking up all the space. I have 100MB available, the database size is 16.5MB. Can the .ldb file take up the remaining space? On querying this with the helpdesk, they admitted that my entire db is only 25MB. There is something wrong with my SQL queries and I should check the website. I'm using EF with linq to SQL. Everything was working fine until now... Can there be something that goes wrong in the queries that causes this sort of error? There is nothing wrong to be seen in the db logs, so this error cannot possibly have happened. I should log it next time it happens and contact again. I found some posts suggesting that restoring a DB backup can get rid of the issue. I do not have a recent backup, and can't take a new one because of a fatal error 9001 occurring. Since this is a shared server I have about 0 authority to execute anything against the DB (think CHECKDB, truncating the log, etc.). So I am at my wits end pretty much. What else can I do/try to get my website moving again?

  Read the article

• Exchange 2007 Email Error 451 4.7.0 Timeout waiting for client input

  - by HK1

  Our SBS 2008 server with Exchange 2007 started rejecting some (most) emails starting about 3 or 4 days ago. The return failure message looks something like this: The error that the other server returned was: 451 451 4.7.0 Timeout waiting for client input (state 18) I've rebooted our Sonicwall TZ-210 router and that doesn't make any difference. I think this problem has something to do with MTU (packet size) but I don't understand why the problem just started now. We haven't made any changes to our network infrastructure for weeks. If I ping our SonicWall (DSL connection, bridge mode) forcing unfragmented packets, I start getting packet dropouts at packet size 1320 or so. Maybe this is completely normal, I'm not sure. I haven't tried rebooting the DSL modem yet because I'm not on site. That's one of the next things I'll try.

  Read the article

• OSSEC : send alerts true gmail? how?

  - by Rubytastic

  Try to setup OSSEC to use google gmail to send my alerts like so: <email_notification>yes</email_notification> <email_to>[email protected]</email_to> <smtp_server>smtp.gmail.com</smtp_server> <email_from>ossec@host</email_from> Then I set email alerts value to 3 and restart ossec. This does not trigger email alert. how to correctly send alerts with gmail? better way to test if mails are sending out?

  Read the article

• Changes made to cli's php.ini not taking effect

  - by Sandeepan Nath

  I have two php.ini files - /etc/php.ini which loads in case of cli /opt/lampp/etc/php.ini which loads in case of browser. I am able to use PHP's Mailparse extension after adding the line extension=mailparse.so in the /opt/lampp/etc/php.ini and restarting lampp. But I am not able to load the same in case of command line - getting PHP Fatal error: Call to undefined function mailparse_msg_create() in ... mailparse_msg_create() is a part of the Mailparse extension. I tried by relogging with the user after making the change and even restarting the system. What needs to be done so that the change takes effect. Update I checked that php -i | grep 'Configuration File' gives PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/mailparse.so' - /usr/lib/php/modules/mailparse.so: cannot open shared object file: No such file or directory in Unknown on line 0 Configuration File (php.ini) Path => /etc Loaded Configuration File => /etc/php.ini Update 2 I copied the mailparse.so from /opt/lampp/lib/php/extensions/no-debug-non-zts-20090626 and put it in /usr/lib/php/modules. I added extension=mailparse.so to /etc/php.ini as well. But it still showed this warning PHP Warning: PHP Startup: Unable to load dynamic library ... As told by Lekensteyn, I did ldd /usr/lib/php/modules/mailparse.so and got ldd: warning: you do not have execution permission for /usr/lib/php/modules/mailparse.so' So I gave execute permission. Then ldd /usr/lib/php/modules/mailparse.so showed linux-gate.so.1 => (0x00110000) libc.so.6 => /lib/libc.so.6 (0x0011d000) /lib/ld-linux.so.2 (0x003aa000) which looks normal. BUt now, running php command says PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/mailparse.so' - /usr/lib/php/modules/mailparse.so: undefined symbol: mbfl_name2no_encoding in Unknown on line 0

  Read the article

• which performance counters mainly matter for windows server performance?

  - by Karl Cassar

  We have a website which is sometimes performing slowly, and / or completely hangs. I have setted up temporarily the default system performance data collector in Performance Monitor, to see if this can shed some light. However, the default Data Collector set collects a huge amount of counters, as well as generates huge logs files. Just 8 hours of data resulted in 4GB of data. Which performance counters matter the most, when judging server load? Also, is it a performance concern if one leaves such data-collectors running indefinitely? Obviously, I will not know when the server will experience slow performance, so I need the logs there so that I can check them out. Any other specific guidelines on monitoring server performance would be greatly appreciated. OS is a Windows Server 2008 R2 (Web Edition).

  Read the article

• Mono fast cgi not working on nginx

  - by Luka Horvatic

  I installed mono fast cgi for nginx following instructions on: http://www.mono-project.com/FastCGI_Nginx but when i try to load test aspx file i getting 502 error gateway,and following error in error log: 2011/11/28 18:49:51 [error] 5376#0: *6 upstream sent unexpected FastCGI record: 3 while reading response header from upstream, client: ipadress, server: ipadress, request: "GET /default.aspx HTTP/1.1", upstream: "fastcgi://127.0.0.1:9999", host: "ipadress" I tried different things to change but always same result,except maybe sometime in error log is number 1 or 3 instead 6.Nginx ver is 1.03 64 bit,mono and xsp latest versions. Any idea what could be wrong?

  Read the article

• Gitosis setup, fatal error on initial clone of gitosis-admin

  - by TheDeeno

  I'm stuck. After setting up gitosis, cloning gitosis-admin for the first time results in the following: $ git clone ssh://[email protected]:gitosis-admin.git Initialized empty Git repository in c:/path/to/my/repo Using username "git-upload-pack 'git". fatal: The remote end hung up unexpectedly Anyone ever experience this problem? Troubleshooting ideas?

  Read the article

• SUSE EC2 Problem - zypper - Permission denied

  - by phuu

  I'm trying to use zypper to install gcc on my Amazon EC2 instance running SUSE.When I try:zypper in gcc I get: Retrieving repository 'SLE11-SDK-SP1' metadata [] Permission to access 'http://eu-west-1-ec2-update.susecloud.net/repo/install/SLE11-SDK-SP1/sle-11-i586/media.1/media' denied. Abort, retry, ignore? [a/r/i/?] (a): i Retrieving repository 'SLE11-SDK-SP1' metadata [error] Repository 'SLE11-SDK-SP1' is invalid. Can't provide /media.1/media : User-requested skipping of a file Please check if the URIs defined for this repository are pointing to a valid repository. Warning: Disabling repository 'SLE11-SDK-SP1' because of the above error. Retrieving repository 'SLE11-SDK-SP1-Updates' metadata [|] Permission to access 'http://eu-west-1-ec2-update.susecloud.net/repo/update/SLE11-SDK-SP1-Updates/sle-11-i586/repodata/repomd.xml' denied. Abort, retry, ignore? [a/r/i/?] (a): i Retrieving repository 'SLE11-SDK-SP1-Updates' metadata [error] Repository 'SLE11-SDK-SP1-Updates' is invalid. Can't provide /repodata/repomd.xml : User-requested skipping of a file Please check if the URIs defined for this repository are pointing to a valid repository. Warning: Disabling repository 'SLE11-SDK-SP1-Updates' because of the above error. Retrieving repository 'SLES11-Extras' metadata [/] Permission to access 'http://eu-west-1-ec2-update.susecloud.net/repo/update/SLES11-Extras/sle-11-i586/repodata/repomd.xml' denied. Abort, retry, ignore? [a/r/i/?] (a): r Permission to access 'http://eu-west-1-ec2-update.susecloud.net/repo/update/SLES11-Extras/sle-11-i586/repodata/repomd.xml' denied. Abort, retry, ignore? [a/r/i/?] (a): zypper in gcc Invalid answer 'zypper in gcc'. [a/r/i/?] (a): a Retrieving repository 'SLES11-Extras' metadata [error] Repository 'SLES11-Extras' is invalid. Can't provide /repodata/repomd.xml : Please check if the URIs defined for this repository are pointing to a valid repository. Warning: Disabling repository 'SLES11-Extras' because of the above error. Retrieving repository 'SLES11-SP1' metadata [-] Permission to access 'http://eu-west-1-ec2-update.susecloud.net/repo/install/SLES11-SP1/sle-11-i586/media.1/media' denied. Abort, retry, ignore? [a/r/i/?] (a): a Retrieving repository 'SLES11-SP1' metadata [error] Repository 'SLES11-SP1' is invalid. Can't provide /media.1/media : Please check if the URIs defined for this repository are pointing to a valid repository. Warning: Disabling repository 'SLES11-SP1' because of the above error. Retrieving repository 'SLES11-SP1-Updates' metadata [] Permission to access 'http://eu-west-1-ec2-update.susecloud.net/repo/update/SLES11-SP1-Updates/sle-11-i586/repodata/repomd.xml' denied. I've search for the problem and this thread came up, but offered no solutions.I've triedsces-activate. Am I doing something wrong? I should say I'm very new to this, and I admit I don't really know what I'm doing, but I'm trying to learn about setting up and running a server and so I thought I'd throw myself in at the deep(ish) end. Thanks for reading.

  Read the article

• Hyper-V + RRAS NAT + Port Forwarding + RDP, can I get it all working together?

  - by Tom Bull

  I am running a Windows 2008 R2 server with various services running natively and two virtualised servers running on Hyper-V. The hardware server, I'm going to call it REAL1, has one external NIC, to which I can assign any of the following IP addresses: 1.2.3.4, 1.2.3.5, 1.2.3.6, etc... I need to achieve the following: I would like to be able to connect to REAL1 via remote desktop (RDP / port 3389) on one IP address (say 1.2.3.4), but also to the virtualised servers (I'm going to call them VIRTUAL1 and VIRTUAL2) on the other available IP addresses (say 1.2.3.5 and 1.2.3.6). The easiest way of doing this is to connect the virtual servers directly to the external interface and assign them each their own IP address. REAL1 will have 1.2.3.4, VIRTUAL1 will have 1.2.3.5 and VIRTUAL2 will have 1.2.3.6. Unfortunately, although I don't directly manage the two virtual servers, I have responsibility for their security. I would like to have some kind of firewall between the virtual servers an the internet. I have tried running a virtual machine firewall, but have found the performance on Hyper-V pretty terrible. The alternative I am now trying is Routing and Remote Access (RRAS): I have set up a virtual network called 'Internal' and REAL1 has a virtual network adapter connected to this virtual network I have connected each of the virtual servers to this network too I have assigned each server static IP addresses on this virtual network (REAL1 has 10.1.1.1, VIRTUAL1 has 10.1.1.2 and VIRTUAL2 has 10.1.1.3) I have installed RRAS and set up a NAT. The external interface is the external NIC, the internal interface is the virtual NIC connected to the internal network I have assigned all the available external IP addresses to the external NIC on REAL1. The virtual servers have been set up appropriately such that their default gateway is pointing to 10.1.1.1 and they can both access externally. Success! The RRAS is routing packets. The problem I have is that when I try to port forward services from the external IP address on REAL1, it only works if there is not already a service bound to the port. Remote desktop 'greedily' binds to every available IP address on port 3389 on REAL1 so I can't selectively forward incoming traffic for 1.2.3.5:3389 to 10.1.1.2:3389. RRAS will allow me to set up this port forwarding, and no errors come up. It just doesn't work. So the question I have is: Is there a better way of doing this? Or at least is there a way of resolving the apparant conflict between RRAS and everything else on the physical server?

  Read the article

• How to manage sub-domains on WinHost with IIS7 URL Rewrite 2.0?

  - by jrummell

  I'm trying out WinHost and I'm running into some issues with sub-domains. On WinHost, you can have multiple sub-domains per hosting account, but each sub-domain points to the root website. E.g. you can have www.example.com, sub1.example.com, and sub2.example.com but all of them display the content at http://www.example.com/. Other Hosts allow you to point sub-domains to a sub folder in your website. This would allow you to point sub1.example.com to /sub1, sub2.example.com to /sub2 and www.example.com to /. WinHost recommends using an asp/aspx page to redirect http://sub1.example.com to http://sub1.example.com/sub1, which points to /sub1. While that would work, I'd like to not have the subdomain in the url twice. So I tried using IIS7 URL Rewrite to point http://sub1.example.com to /sub1. Ben Powell describes this in detail on his blog. This is great, except Request.ApplicationPath is now /sub1/path/to/current/page.aspx, which breaks ASP.Net Themes (and probably other stuff too). What can I do to fix the ApplicationPath? Is there a better way to accomplish this?

  Read the article

• Router for creating site to site VPN to server provider using Cisco ASA 5540

  - by fondie

  We have dedicated servers hosted for us by a third party, we connect to these over a VPN. My server provider uses Cisco ASA 5540 as VPN devices. Currently we're using software clients on individual machines to connect to this VPN, either: Cisco VPN Client Shrew Soft VPN Connect However, I'm looking to purchase a new load balancing router for our office and thought this could be an opportunity to get VPN client duties taken over by hardware. We could then create a permanent VPN tunnel that could be used by anyone on the network with no software client necessary. Sadly I'm not the most knowledgeable on this kind of stuff so is: 1) This a realizable goal? Next I need to know what kind of hardware I will need. I'm not looking to spend lots of money on this (~$500), so doubtful I can afford any Cisco kit. Therefore, this is the most promising candidate I've seen (as far as my limited knowledge goes): Draytek Vigor 2955 - http://www.draytek.co.uk/products/vigor2955.html 2) Would this be compatible with the Cisco kit my server provider uses? 3) If not, are there any alternatives I should consider? Many thanks in advance.

  Read the article

• How to set up spf records to send mail from google hosted apps to gmail addresses

  - by Chris Adams

  Hi there, I'm trying to work out why email I send from one domain I own is rejected by another that I own, and while I think it may be related to how I've setup spf records, I'm not sure what steps I need to take to fix it. Here's the error message I receive: Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550-Verification failed for <[email protected]> 550-No Such User Here 550 Sender verify failed (state 14). Here's the response from [email protected] Delivered-To: [email protected] Received: by 10.86.92.9 with SMTP id p9cs85371fgb; Wed, 2 Sep 2009 22:33:32 -0700 (PDT) Received: by 10.90.205.4 with SMTP id c4mr2406190agg.29.1251956007562; Wed, 02 Sep 2009 22:33:27 -0700 (PDT) Return-Path: <[email protected]> Received: from verifier.port25.com (207-36-201-235.ptr.primarydns.com [207.36.201.235]) by mx.google.com with ESMTP id 26si831174aga.24.2009.09.02.22.33.25; Wed, 02 Sep 2009 22:33:26 -0700 (PDT) Received-SPF: pass (google.com: domain of [email protected] designates 207.36.201.235 as permitted sender) client-ip=207.36.201.235; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 207.36.201.235 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha1; c=relaxed/relaxed; s=auth; d=port25.com; h=Date:From:To:Subject:Message-Id:In-Reply-To; [email protected]; bh=GRMrcnoucTl4upzqJYTG5sOZMLU=; b=uk6TjADEyZVRkceQGjH94ZzfVeRTsiZPzbXuhlqDt1m+kh1zmdUEoiTOzd89ryCHMbVcnG1JajBj 5vOMKYtA3g== DomainKey-Signature: a=rsa-sha1; c=nofws; q=dns; s=auth; d=port25.com; b=NqKCPK00Xt49lbeO009xy4ZRgMGpghvcgfhjNy7+qI89XKTzi6IUW0hYqCQyHkd2p5a1Zjez2ZMC l0u9CpZD3Q==; Received: from verifier.port25.com (127.0.0.1) by verifier.port25.com (PowerMTA(TM) v3.6a1) id hjt9pq0hse8u for <[email protected]>; Thu, 3 Sep 2009 01:26:52 -0400 (envelope-from <[email protected]>) Date: Thu, 3 Sep 2009 01:26:52 -0400 From: [email protected] To: [email protected] Subject: Authentication Report Message-Id: <[email protected]> Precedence: junk (auto_reply) In-Reply-To: <[email protected]> This message is an automatic response from Port25's authentication verifier service at verifier.port25.com. The service allows email senders to perform a simple check of various sender authentication mechanisms. It is provided free of charge, in the hope that it is useful to the email community. While it is not officially supported, we welcome any feedback you may have at <[email protected]>. Thank you for using the verifier, The Port25 Solutions, Inc. team ========================================================== Summary of Results ========================================================== SPF check: pass DomainKeys check: neutral DKIM check: neutral Sender-ID check: pass SpamAssassin check: ham ========================================================== Details: ========================================================== HELO hostname: fg-out-1718.google.com Source IP: 72.14.220.158 mail-from: [email protected] ---------------------------------------------------------- SPF check details: ---------------------------------------------------------- Result: pass ID(s) verified: [email protected] DNS record(s): stemcel.co.uk. 14400 IN TXT "v=spf1 include:aspmx.googlemail.com ~all" aspmx.googlemail.com. 7200 IN TXT "v=spf1 redirect=_spf.google.com" _spf.google.com. 300 IN TXT "v=spf1 ip4:216.239.32.0/19 ip4:64.233.160.0/19 ip4:66.249.80.0/20 ip4:72.14.192.0/18 ip4:209.85.128.0/17 ip4:66.102.0.0/20 ip4:74.125.0.0/16 ip4:64.18.0.0/20 ip4:207.126.144.0/20 ?all" ---------------------------------------------------------- DomainKeys check details: ---------------------------------------------------------- Result: neutral (message not signed) ID(s) verified: [email protected] DNS record(s): ---------------------------------------------------------- DKIM check details: ---------------------------------------------------------- Result: neutral (message not signed) ID(s) verified: NOTE: DKIM checking has been performed based on the latest DKIM specs (RFC 4871 or draft-ietf-dkim-base-10) and verification may fail for older versions. If you are using Port25's PowerMTA, you need to use version 3.2r11 or later to get a compatible version of DKIM. ---------------------------------------------------------- Sender-ID check details: ---------------------------------------------------------- Result: pass ID(s) verified: [email protected] DNS record(s): stemcel.co.uk. 14400 IN TXT "v=spf1 include:aspmx.googlemail.com ~all" aspmx.googlemail.com. 7200 IN TXT "v=spf1 redirect=_spf.google.com" _spf.google.com. 300 IN TXT "v=spf1 ip4:216.239.32.0/19 ip4:64.233.160.0/19 ip4:66.249.80.0/20 ip4:72.14.192.0/18 ip4:209.85.128.0/17 ip4:66.102.0.0/20 ip4:74.125.0.0/16 ip4:64.18.0.0/20 ip4:207.126.144.0/20 ?all" ---------------------------------------------------------- SpamAssassin check details: ---------------------------------------------------------- SpamAssassin v3.2.5 (2008-06-10) Result: ham (-2.6 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- -0.0 SPF_PASS SPF: sender matches SPF record -2.6 BAYES_00 BODY: Bayesian spam probability is 0 to 1% [score: 0.0000] 0.0 HTML_MESSAGE BODY: HTML included in message I've registered the spf records for my domain, as advised here Both domains pass validate according to Kitterman's spf record testing tools, so I'm somewhat confused about this. I also have the catchall address set up on the stemcel.co.uk domain here, but I don't have one setup for chrisadams.me.uk. Instead, we have the following forwarders setup [email protected] to [email protected] [email protected] to [email protected] [email protected] to [email protected] [email protected] to [email protected] Any ideas how to get this working? I'm not sure what I should be looking for here.

  Read the article

• apache Client Certificate Authentication errors: Certificate Verification: Error (18): self signed certificate

  - by decoy

  So I have been following instructions on setting up Client Certificate Authentication in Apache2 w/ mod_ssl. This is solely for the purpose of testing an application against CAA, not for any sort of production use. So far I've followed http://www.impetus.us/~rjmooney/projects/misc/clientcertauth.html for advice on generating my CA, server, and client encryption information. I've put all three of them into /etc/ssl/ca/private. I've setup the following additional directives in my default_ssl site file: <IfModule mod_ssl.c> <VirtualHost _default_:443> ... SSLEngine on SSLCertificateFile /etc/ssl/ca/private/server.crt SSLCertificateKeyFile /etc/ssl/ca/private/server.key SSLVerifyClient require SSLVerifyDepth 2 SSLCACertificatePath /etc/ssl/ca/private SSLCACertificateFile /etc/ssl/ca/private/ca.crt <Location /> SSLRequireSSL SSLVerifyClient require SSLVerifyDepth 2 </Location> <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory /usr/lib/cgi-bin> SSLOptions +StdEnvVars </Directory> ... </VirtualHost> </IfModule> I've install the p12 file into Chrome, but when I go to visit https://localhost, I get the following errors Chrome: Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error. Apache: Certificate Verification: Error (18): self signed certificate If I had to guess, one of my directives is not setup right to load and verify the p12 w/ my self created CA. But I can't for the life of me figure out what it is. Would anyone have more experience here who could point me in the right direction?

  Read the article

• Backup and Restore ADAM database

  - by kuoson

  Hi, I was trying to backup and restore an ADAM database to a different server the other day. I copied all files under "Program Files/Microsoft ADAM" folder to the same path in the destination server and started the ADAM service in the destination server up. Although the service come back up successfully and I was able to connect to the instance with ADAM ADSI Edit mmc snap-in, I found I had to reset every single user's password before they can login again. Has anyone got this issue before? Is the password encrypted with the server IP address or something like that?

  Read the article

• Postfix throttling for outgoing messages

  - by Sergey Kovalev

  I need Postfix to send outgoing messages (from local PHP) with a certain rate. Say, one message in 120 seconds. Any messages exceeding this rate should be queued (delayed) and delivered later. Policyd is not what I'm looking for. I don't need limiting overall number of messages sent. I need a pause (120s) between any two messages beeing sent. Tried this config, but it's not working: initial_destination_concurrency = 1 default_destination_concurrency_limit = 1 default_destination_rate_delay = 120 default_destination_recipient_limit = 1 default_process_limit = 1 Any suggestions?

  Read the article

• Ubuntu Apache 10 second timeout

  - by Andreas Jansson

  Hi, I'm debugging an API I'm building using netcat to send raw HTTP requests. The thing is that Apache closes the connection after 10 seconds, giving me very little time to type. I know that I could pipe a file to nc, or use any other workaround, but I'd like it to work as it's supposed to. The Timeout directive in apache2.conf is at its default of 300 seconds, KeetAliveTimeout at 15 seconds. Where could this 10 second timeout possibly be defined? I'm running Ubuntu 10.04 Desktop. Thanks, Andreas

  Read the article

• Speedstep and Intel x5570?

  - by sajal

  Hi, My new server has 2 x X5570 CPUs. Now here is the output of grep -i hz /proc/cpuinfo model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 model name : Intel(R) Xeon(R) CPU X5570 @ 2.93GHz cpu MHz : 1600.231 It always remains the same.. no matter how much load is mysql or any other app hogging. Even when mysql eats 2 or 3 CPUs at 100% each, the output of cpuinfo is the same. If fact mysql performance for some heavy inserts is poorer than my old E5430 server. Any clues? I contacted the server provider, they tried turning off SpeedStep and still we see the same results. Any insights would be helpful cause I am paying heavily for this box and would love to milk all juice i can.

  Read the article

• gen-msg.map missing in Snort rules?

  - by TheLQ

  I am trying to install Snort 2.8.4.1 (only package available in the repos) with Barnyard2 with limited success. I've managed to fix everything but this: [lordquackstar@quackwall rules]$ sudo barnyard2 -c /etc/snort/barnyard2.conf -d /var/log/snort -f snort.u2 -w /etc/snort/barny Password: Running in Continuous mode --== Initializing Barnyard2 ==-- Initializing Input Plugins! Initializing Output Plugins! Parsing config file "/etc/snort/barnyard2.conf" ERROR: Unable to open Generator file "/etc/snort/gen-msg.map": No such file or directory ERROR: Stat check on log dir (/var/log/barnyard2) failed: No such file or directory. Fatal Error, Quitting.. The gen-msg.map error is puzzling me. The rulesets that come with the package do not contain this file. The newish rules I just downloaded from Snort.org for version 2.8.6.1 don't have this file. The only file that looks close is called sid-msg.map, but that's the wrong one. Where can I obtain this file? Just in case it matters: The packages come from the ClearOS repositories (OS is based off of CentOS). I'm running CentOS 5.2

  Read the article

• Can't install Perl DBD module on Ubuntu (for Bugzilla)

  - by Mara

  Trying to install bugzilla-4.2.2 on Ubuntu 12.04. When I run checksetup.pl I get the following error: YOU MUST RUN ONE OF THE FOLLOWING COMMANDS (depending on which database you use): PostgreSQL: /usr/bin/perl install-module.pl DBD::Pg MySQL: /usr/bin/perl install-module.pl DBD::mysql SQLite: /usr/bin/perl install-module.pl DBD::SQLite Oracle: /usr/bin/perl install-module.pl DBD::Oracle To attempt an automatic install of every required and optional module with one command, do: /usr/bin/perl install-module.pl --all I have installed MySQL via XAMPP so I run: /urs/bin/perl install-module.pl DBD::mysql And get the following error: perl Makefile.PL --testuser=username Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Failed to determine directory of mysql.h. Use perl Makefile.PL --cflags=-I<dir> to set this directory. For details see the INSTALL.html file, section "C Compiler flags" or type perl Makefile.PL --help Warning: No success on command[/usr/bin/perl Makefile.PL LIB="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib" INSTALLMAN1DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man1" INSTALLMAN3DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man3" INSTALLBIN="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLSCRIPT="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLDIRS=perl] CAPTTOFU/DBD-mysql-4.021.tar.gz /usr/bin/perl Makefile.PL LIB="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib" INSTALLMAN1DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man1" INSTALLMAN3DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man3" INSTALLBIN="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLSCRIPT="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLDIRS=perl -- NOT OK Skipping test because of notest pragma Running make install Make had some problems, won't install Could not read metadata file. Falling back to other methods to determine prerequisites So then I tried checksetup.pl's suggestion and ran: /usr/bin/perl install-module.pl --all And it seems to have installed DBD::SQLite without any problems, but again I see a warning that says it's skipping tests because of notest pragma. When I re-run checksetup.pl It shows 3 of the 4 original DB drivers in the "not found" list: PostgreSQL: /usr/bin/perl install-module.pl DBD::Pg MySQL: /usr/bin/perl install-module.pl DBD::mysql Oracle: /usr/bin/perl install-module.pl DBD::Oracle So running it with --all seems to have installed the SQLite driver without any problems, but for some reason I can't seem to install the MySQL driver. Again I need MySQL because thats what XAMPP uses and because I prefer MySQL regardless. I have a feeling it has something to do with this notest pragma error. Any ideas? Thanks in advance!

  Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >