Search Results

Search found 1877 results on 76 pages for 'vendor'.

Page 74/76 | < Previous Page | 70 71 72 73 74 75 76  | Next Page >

• SATA errors reported during boot: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0

  - by digby280

  I have noticed some error during the Linux boot. They seem to continue to occur after the boot adding lines to the log every few seconds. Once booted this normally does not appear to be causing any problems. However, around 1 in 10 boots results in a kernel panic and the computer has on two or three occasions suddenly rebooted after being powered on for a number of hours. I presume the cause of the reboot is a kernel panic as well. I am running Ubuntu 11.10 and I have had Ubuntu installed on the computer for around a year. I have googled around and not found anything useful. I have provided the kernel log lines and the output of smartctl. Can anyone explain exactly what these errors mean, or better still how to resolve them? Apr 2 16:51:27 dell580 kernel: [ 19.831140] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 Apr 2 16:51:27 dell580 kernel: [ 19.934194] tg3 0000:03:00.0: eth0: Link is down Apr 2 16:51:28 dell580 kernel: [ 20.929468] tg3 0000:03:00.0: eth0: Link is up at 100 Mbps, full duplex Apr 2 16:51:28 dell580 kernel: [ 20.929471] tg3 0000:03:00.0: eth0: Flow control is on for TX and on for RX Apr 2 16:51:28 dell580 kernel: [ 20.929727] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Apr 2 16:51:29 dell580 kernel: [ 21.609381] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 Apr 2 16:51:29 dell580 kernel: [ 21.616515] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:29 dell580 kernel: [ 21.616519] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:29 dell580 kernel: [ 21.616525] ata2.00: hard resetting link Apr 2 16:51:29 dell580 kernel: [ 21.934036] ata2.01: hard resetting link Apr 2 16:51:29 dell580 kernel: [ 22.408890] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:29 dell580 kernel: [ 22.408907] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:29 dell580 kernel: [ 22.440934] ata2.00: configured for UDMA/100 Apr 2 16:51:29 dell580 kernel: [ 22.449040] ata2.01: configured for UDMA/133 Apr 2 16:51:29 dell580 kernel: [ 22.449818] ata2: EH complete Apr 2 16:51:33 dell580 kernel: [ 26.122664] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:33 dell580 kernel: [ 26.122670] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:33 dell580 kernel: [ 26.122677] ata2.00: hard resetting link Apr 2 16:51:33 dell580 kernel: [ 26.442684] ata2.01: hard resetting link Apr 2 16:51:34 dell580 kernel: [ 26.925545] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:34 dell580 kernel: [ 26.925561] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:34 dell580 kernel: [ 26.961542] ata2.00: configured for UDMA/100 Apr 2 16:51:34 dell580 kernel: [ 26.969616] ata2.01: configured for UDMA/133 Apr 2 16:51:34 dell580 kernel: [ 26.970400] ata2: EH complete Apr 2 16:51:35 dell580 kernel: [ 28.111180] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:35 dell580 kernel: [ 28.111184] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:35 dell580 kernel: [ 28.111191] ata2.00: hard resetting link Apr 2 16:51:35 dell580 kernel: [ 28.429674] ata2.01: hard resetting link Apr 2 16:51:36 dell580 kernel: [ 28.904557] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:36 dell580 kernel: [ 28.904572] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:36 dell580 kernel: [ 28.936609] ata2.00: configured for UDMA/100 Apr 2 16:51:36 dell580 kernel: [ 28.944692] ata2.01: configured for UDMA/133 Apr 2 16:51:36 dell580 kernel: [ 28.945464] ata2: EH complete Apr 2 16:51:38 dell580 kernel: [ 31.581756] eth0: no IPv6 routers present Apr 2 16:51:38 dell580 kernel: [ 32.103066] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:38 dell580 kernel: [ 32.103074] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:38 dell580 kernel: [ 32.103085] ata2.00: hard resetting link Apr 2 16:51:38 dell580 kernel: [ 32.419669] ata2.01: hard resetting link Apr 2 16:51:39 dell580 kernel: [ 32.894518] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:39 dell580 kernel: [ 32.894533] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:39 dell580 kernel: [ 32.926536] ata2.00: configured for UDMA/100 Apr 2 16:51:39 dell580 kernel: [ 32.934715] ata2.01: configured for UDMA/133 Apr 2 16:51:39 dell580 kernel: [ 32.935578] ata2: EH complete Here's the output of smartctl for the drive. smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-17-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD103UJ Serial Number: S13PJ90QC19706 LU WWN Device Id: 5 0000f0 00b1c7960 Firmware Version: 1AA01113 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3b Local Time is: Mon Apr 2 17:13:48 2012 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: (11772) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 197) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 076 076 011 Pre-fail Always - 7940 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 521 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 642 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 482 13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 759 184 End-to-End_Error 0x0033 100 100 000 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 073 069 000 Old_age Always - 27 (Min/Max 16/27) 194 Temperature_Celsius 0x0022 073 067 000 Old_age Always - 27 (Min/Max 16/28) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 320028 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 099 099 000 Old_age Always - 1494 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 211 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 211 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 0f 31 63 8f e1 Error: ICRC, ABRT 15 sectors at LBA = 0x018f6331 = 26174257 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 40 62 8f e1 08 00:01:00.460 READ DMA c8 00 20 00 7c 30 e0 08 00:01:00.450 READ DMA c8 00 00 10 49 8f e1 08 00:01:00.440 READ DMA c8 00 e0 20 d0 30 e0 08 00:01:00.420 READ DMA c8 00 00 c0 59 90 e1 08 00:01:00.400 READ DMA Error 210 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 cf e9 cf 66 e0 Error: ICRC, ABRT 207 sectors at LBA = 0x0066cfe9 = 6737897 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 b8 cf 66 e0 08 00:08:29.780 READ DMA c8 00 60 60 c9 18 e0 08 00:08:29.770 READ DMA c8 00 40 20 c9 18 e0 08 00:08:29.770 READ DMA c8 00 20 00 c9 18 e0 08 00:08:29.760 READ DMA c8 00 20 98 cf 66 e0 08 00:08:29.750 READ DMA Error 209 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 2f d1 74 e0 e0 Error: ICRC, ABRT 47 sectors at LBA = 0x00e074d1 = 14709969 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 00 74 e0 e0 08 00:00:30.940 READ DMA c8 00 20 18 36 de e0 08 00:00:30.930 READ DMA c8 00 08 48 f1 dd e0 08 00:00:30.930 READ DMA c8 00 08 a8 f0 dd e0 08 00:00:30.930 READ DMA c8 00 08 90 f0 dd e0 08 00:00:30.930 READ DMA Error 208 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 7f 21 88 9d e0 Error: ICRC, ABRT 127 sectors at LBA = 0x009d8821 = 10324001 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 a0 00 88 9d e0 08 00:00:27.610 READ DMA c8 00 58 a8 e7 9c e0 08 00:00:27.610 READ DMA c8 00 00 28 e6 9c e0 08 00:00:27.610 READ DMA c8 00 00 e0 e4 9c e0 08 00:00:27.610 READ DMA c8 00 00 90 e0 9c e0 08 00:00:27.600 READ DMA Error 207 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 26 6a 6a c3 e0 Error: ABRT at LBA = 0x00c36a6a = 12806762 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 00 90 69 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 90 68 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 50 65 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 d0 64 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 90 63 c3 e0 08 00:29:39.350 WRITE DMA SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 90% 638 - # 2 Short offline Interrupted (host reset) 90% 638 - # 3 Extended offline Interrupted (host reset) 90% 638 - # 4 Short offline Interrupted (host reset) 90% 638 - # 5 Extended offline Interrupted (host reset) 90% 638 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

  Read the article

• CodePlex Daily Summary for Saturday, June 08, 2013

  CodePlex Daily Summary for Saturday, June 08, 2013Popular ReleasesXomega Framework: Xomega.Framework 1.4: Adding support for Visual Studio 2012 and .Net framework 4.5. Minor bug fixes and enhancements.sb0t v.5: sb0t 5.14: Stability fix in script engine. Avatar.exists property fixed in scripting. cb0t custom font protocol re-added and updated to support new Ares.ASP.NET MVC Forum: MVCForum v1.3.5: This is a bug release version, with a couple of small usability features and UI changes. All the small amount of bugs reported in v1.3 have been fixed, no upgrade needed just overwrite the files and everything should just work.Json.NET: Json.NET 5.0 Release 6: New feature - Added serialized/deserialized JSON to verbose tracing New feature - Added support for using type name handling with ISerializable content Fix - Fixed not using default serializer settings with primitive values and JToken.ToObject Fix - Fixed error writing BigIntegers with JsonWriter.WriteToken Fix - Fixed serializing and deserializing flag enums with EnumMember attribute Fix - Fixed error deserializing interfaces with a valid type converter Fix - Fixed error deser...IIS Express GUI: IISExpressGUI Version 1.0 beta: This is a beta version Tested on Windows Xp (IISExpress 7.5) and Windows 8 (IISExpress 8.0) Works with default installation path for IISExpress Manages only web sites configured in IIS Express applicationhost.config Works with default path for applicationhost.config Application expects that applicationhost.config existsDNN Extension Url Providers: Latest Release: Latest Release of all Extension Url ProvidersChristoc's DotNetNuke Module Development Template: DotNetNuke 7 Project Templates V2.3 for VS2012: V2.3 - Release Date 6/5/2013 Items addressed in this 2.3 release Fixed bad namespace for BusinessController in one of the C# templates. Updated documentation in all templates. Setting up your DotNetNuke Module Development Environment Installing Christoc's DotNetNuke Module Development Templates Customizing the latest DotNetNuke Module Development Project TemplatesPulse: Pulse 0.6.7.0: A number of small bug fixes to stabilize the previous Beta. Sorry about the never ending "New Version" bug!QlikView Extension - Animated Scatter Chart: Animated Scatter Chart - v1.0: Version 1.0 including Source Code qar File Example QlikView application Tested With: Browser Firefox 20 (x64) Google Chrome 27 (x64) Internet Explorer 9 QlikView QlikView Desktop 11 - SR2 (x64) QlikView Desktop 11.2 - SR1 (x64) QlikView Ajax Client 11.2 - SR2 (based on x64)BarbaTunnel: BarbaTunnel 7.2: Warning: HTTP Tunnel is not compatible with version 6.x and prior, HTTP packet format has been changed. Check Version History for more information about this release.SuperWebSocket, a .NET WebSocket Server: SuperWebSocket 0.8: This release includes these changes below: Upgrade SuperSocket to 1.5.3 which is much more stable Added handshake request validating api (WebSocketServer.ValidateHandshake(TWebSocketSession session, string origin)) Fixed a bug that the m_Filters in the SubCommandBase can be null if the command's method LoadSubCommandFilters(IEnumerable<SubCommandFilterAttribute> globalFilters) is not invoked Fixed the compatibility issue on Origin getting in the different version protocols Marked ISub...BlackJumboDog: Ver5.9.0: 2013.06.04 Ver5.9.0 (1) ?????????????????????????????????($Remote.ini Tmp.ini) (2) ThreadBaseTest?? (3) ????POP3??????SMTP???????????????? (4) Web???????、?????????URL??????????????? (5) Ftp???????、LIST?????????????? (6) ?????????????????????Media Companion: Media Companion MC3.569b: New* Movies - Autoscrape/Batch Rescrape extra fanart and or extra thumbs. * Movies - Alternative editor can add manually actors. * TV - Batch Rescraper, AutoScrape extrafanart, if option enabled. Fixed* Movies - Slow performance switching to movie tab by adding option 'Disable "Not Matching Rename Pattern"' to Movie Preferences - General. * Movies - Fixed only actors with images were scraped and added to nfo * Movies - Fixed filter reset if selected tab was above Home Movies. * Updated Medi...Nearforums - ASP.NET MVC forum engine: Nearforums v9.0: Version 9.0 of Nearforums with great new features for users and developers: SQL Azure support Admin UI for Forum Categories Avoid html validation for certain roles Improve profile picture moderation and support Warn, suspend, and ban users Web administration of site settings Extensions support Visit the Roadmap for more details. Webdeploy package sha1 checksum: 9.0.0.0: e687ee0438cd2b1df1d3e95ecb9d66e7c538293b Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.93: Added -esc:BOOL switch (CodeSettings.AlwaysEscapeNonAscii property) to always force non-ASCII character (ch > 0x7f) to be escaped as the JavaScript \uXXXX sequence. This switch should be used if creating a Symbol Map and outputting the result to the a text encoding other than UTF-8 or UTF-16 (ASCII, for instance). Fixed a bug where a complex comma operation is the operand of a return statement, and it was looking at the wrong variable for possible optimization of = to just .VG-Ripper & PG-Ripper: VG-Ripper 2.9.42: changes NEW: Added Support for "GatASexyCity.com" links NEW: Added Support for "ImgCloud.co" links NEW: Added Support for "ImGirl.info" links NEW: Added Support for "SexyImg.com" links FIXED: "ImageBam.com" linksDocument.Editor: 2013.22: What's new for Document.Editor 2013.22: Improved Bullet List support Improved Number List support Minor Bug Fix's, improvements and speed upsCarrotCake, an ASP.Net WebForms CMS: Binaries and PDFs - Zip Archive (v. 4.3 20130528): Features include a content management system and a robust featured blogging engine. This includes configurable date based blog post URLs, blog post content association with categories and tags, assignment/customization of category and tag URL patterns, simple blog post feedback collection and review, blog post pagination/indexes, designation of default blog page (required to make search, category links, or tag links function), URL date formatting patterns, RSS feed support for posts and pages...PHPExcel: PHPExcel 1.7.9: See Change Log for details of the new features and bugfixes included in this release, and methods that are now deprecated.Droid Explorer: Droid Explorer 0.8.8.10 Beta: Fixed issue with some people having a folder called "android-4.2.2" in their build-tools path. - 16223 New ProjectsActiveRoad: IRoad browser settings library Configuration for authentication and data validation iRoad system.AeroHockey: -ASP.NET Web Form Survey: Survey Management, virtual project for ASP.NET Web Form group members.BattleFury: BattleFury is a Game where multiple players can log into a server and fight against each other. The twist is that you can use the given libraries to create codeDomino to Exchange Migration: A Multifunctional server migration tool Mail Migration Wizard is a batch conversion method that flawlessly accomplishes bulk NSF to PST migration or Lotus NotesEAV Manager: Allows users add entities and manager entitiesGet country name from IP: This is an API that outputs two letter country name for a given IP address. This api gives accurate name of the country for a given IPv4 address.Gpx File Cleaner: The GPX file cleaner is a small geocaching tool to remove vendor specific XML elements from a GPX file and reduces the information to the baseline GPX 1.0.HIPC: Party Time!Kunlun: ????????，???? ?? ?????????????，???????C/S????New-NuGetPackage PowerShell Script: New-NuGetPackage.ps1 is a PowerShell script to make creating and publishing NuGet packages quick and easy, whether packing from a .nuspec or project file.ProXR Library: The Pro XR library is a native C# library for communicating to a Pro XR relay controller over TCP/IP or serial port communications. Sarcasm: Fuck yeahSE_Agency_Project: ????? ?? ????? ???? ????? ?????????SharpDevelop Version Selector: This is a replacement for the Visual Studio Version Selector that allows the user to open SLN files based off of user defined rules.SPBusiness: Business Classes to support SharePoint DevelopmentStepsManager: An all in one library to implement a step management in your application in few lines of code.Switchboard: A simple message broker that receives messages from a queue and passes them to plug-in handlers loaded at run time.TasteKidSharp: C# TasteKid API wrapper (www.tastekid.com) ThriveFast SharePoint Utilities: A collection of useful utilities for SharePoint 2010 & 2013 brought to you by ThriveFast. TopBoss: TestingWCSF Contrib Modular Sitemap / Nav Graph (Example): This is NOT an attempt to fork the great WCSF contrib probject. I wrote some stuff to try to extend the idea of using modules to modularizing the sitemap and using it help provide views for the navigation graphs used by the xml pageflow library. I'm posting the code here so I can get some community feedback related to the validity of ideas, the implementation and possible suggestions on improvement with respect to keeping modules at loosely coupled as possible. Cheers PeteWindows 8 Loopback Exemption Manager: GUI to enable Loopback Exemptions for Windows 8 Modern UI Apps Windows Store App Calendar Control: Windows Store App Calendar Control (XAML)

  Read the article

• How do I prevent missing network from slowing down boot-up?

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Jagran Prakashan Increases Staff Productivity by 40%

  - by Michael Snow

  Jagran Prakashan Increases Staff Productivity by 40%, Launches New IT Projects up to 4x Faster, Enables Mobile Service, and Improves Business Agility Oracle Customer: JPL Location:  Uttar Pradesh, India Industry: Media and Entertainment Employees:  10,000 Annual Revenue:  $100 to $500 Million Jagran Prakashan Ltd. (JPL) is one of India's premier media and communications groups with interests spanning print, advertising, event management, and mobile services for weather, cricket scores, and educational activities. It is a major media enterprise, with 300 locations across 15 states. Its impressive stable of print publications includes Dainik Jagran, the world’s most widely read daily newspaper––with a readership of over 55 million––the country’s leading afternoon dailies, and a range of popular local, bilingual, and English language newspapers. JPL was using multiple systems to manage its business processes. Users were resistant to using multiple passwords for various applications, preferring to continue their less efficient, legacy work practices. In addition, there was no single repository for sharing documents across the organization, such as company announcements or project documents. The company relied on e-mail to disseminate up-to-date company information, often missing employees. It was also time-consuming and difficult for managers to track the status of ongoing assignments or projects because collaboration and document sharing was inefficient and ineffective.With diverse businesses and many geographic locations, JPL needed to implement a centralized and user-friendly enterprise portal to improve document sharing and collaboration and increase business agility. The company implemented Oracle WebCenter Portal to create a dynamic, secure, and intuitive self-service enterprise portal to improve the user experience and increase operating efficiency. It improved staff productivity by 40%, accelerated new IT projects by up to 4x, boosted staff morale, and increased business agility.   Increases Staff Productivity by 40%, Launches New Products up to 2x Faster A word from JPL "With Oracle WebCenter Portal, we gained a dynamic, secure, and intuitive self-service enterprise portal that provided an exceptional user experience and enabled us to engage employees in a collaborative environment. It increased IT staff productivity by 40%, delivered new projects up to 4x faster, and enabled mobile service to improve our business agility.” Sarbani Bhatia, Vice President IT, Jagran Prakashahn Ltd Before implementing Oracle WebCenter Portal, JPL stored project-critical information, such as page planning of daily newspaper editions and the launch of new editions or supplements on individual laptops or in the e-mail system. Collaboration between colleagues was limited to physical meetings, telephone discussions, and e-mail. It was difficult to trace and recover important project documents when a staff member resigned, which represented a significant risk to business continuity. Employees were also averse to multiple passwords and resisted using the systems, affecting staff productivity. With Oracle WebCenter Portal, JPL created a dynamic, secure, and intuitive self-service enterprise portal with business activity streams. The portal allowed users to navigate, discover, and access information, such as advertising rates, requisition approvals, ad-hoc queries, and employee surveys from a single entry point with a single password. Managers can also upload important documents, such as new pricing for advertisers or newspaper distributors, and share them through the information and instruction section in the portal. In addition, managers can now easily track and review timelines for projects online rather than gathering information from meetings and e-mails. The company gained the ability to centrally manage information, ensured business continuity, and improved staff productivity by 40%.“In the media industry, news has a very short shelf life, so speed is crucial. Information delayed is like information lost,” said Sarbani Bhatia, vice president IT, Jagran Prakashahn Ltd. “Thanks to Oracle WebCenter Portal’s contextual collaboration tools, we can provide and share feedback for new project launches, such as career or education supplements, up to 2x faster through discussion forums or knowledge groups. Tasks that previously required four months, we now complete in one month.”In addition, the company can broadcast announcements, flash employee birthdays, and promote important events through the message section on the webpage, instead of using the e-mail system. The company can also conduct opinion polls to gauge employee response to organizational issues and improve management decision-making.“With over 10,000 employees across 300 locations, it is critical for management to hear the voice of employees and develop a cohesive organizational culture. Oracle WebCenter Portal enables employees to engage with business processes and systems in a collaborative environment, providing users with an exceptional experience,” Bhatia said. Enables Mobility Access and Increases Business Agility Newspaper advertisements generate the majority of JPL’s revenue. With most sales staff on the move, the company needed to ensure timely approval of print advertisement discounts for specific clients and meet tight publication deadlines.  By integrating Oracle WebCenter Portal seamlessly with its enterprise resource planning (ERP) system and other applications, such as the organizational mass mailing system, business intelligence, and management information system, JPL embedded its approval workflow processes into the enterprise portal and provided users with an integrated and intuitive interface. About 30% of JPL’s sales staff members now have tablets and receive advertising discount approval from managers while in the field and no longer need to return to the office, which has significantly improved efficiency and increased business agility.“Application mobility was critical for sales representatives in the field to meet stringent auditing requirements for online accountability, particularly for our newspaper advertising business. Staff member satisfaction has improved significantly now that the sales team can use tablets to access the portal––a capability we will extend to smart phones in the second stage of the implementation,” Bhatia said. Accelerates Application Development by up to 4x and Cuts Costs by up to 60% With Oracle WebCenter Portal, users can easily create, modify, and upload information to their personalized webpages without IT assistance. By seamlessly integrating Oracle WebCenter Portal with the payroll database, managers can decide which members of their team can access the page and with whom they will share information, a decision based on role or geographical location. A sales representative selling advertising space for a local language daily newspaper, for example, can upload an updated advertising rate relevant only to that particular publication. Users can also easily adapt to the new platform, thanks to its intuitive design and look, reducing the need for training and lowering resistance to using the system.Using Oracle WebCenter Portal’s out-of-the-box reusable components, such as portal pages and templates, provided JPL’s developers with a comprehensive and flexible user experience platform and increased the speed of application development. In less than five months, JPL developed more than 55 workflows. The IT team accelerated deployment of new applications by up to 4x, as they do not need to install them on individual machines now that they have a web-based environment.   “Previously, we would have spent a whole day deploying a new application for each department or location. With a browser-based environment, we have cut costs by up to 60% by reducing deployment time to zero, because our IT team can roll out a new application from a single point, thanks to Oracle WebCenter Portal,” Bhatia said. Challenges Provide a dynamic, secure, and intuitive self-service enterprise portal to improve staff productivity and ensure business continuity Enable seamless integration with multiple enterprise applications to improve workflow efficiency—including approval of print advertisement discounts—and increase business agility Improve engagement with employees and enable collaboration to enhance management decision-making Accelerate time-to-market for new services, such as new advertising programs Solutions Oracle Product and ServicesOracle WebCenter Portal 11g Increased staff productivity by 40% and enhanced user satisfaction by enabling employees to easily navigate, discover, and access information from a single, self-service enterprise portal without IT assistance Launched new products, such as career or education supplements, up to 2x faster by enabling peer collaboration and incorporating feedback generated through discussion forums, thanks to Oracle WebCenter Portal’s out-of-the-box collaboration tools Accelerated application development up to 4x by enabling developers to optimize reusable components for managing and deploying new applications in a browser-based environment rather than spending one day to install applications for each department, cutting costs by up to 60% Ensured business continuity by enabling managers to easily track and review project timelines online rather than storing important documents on individual laptops or relying on the e-mail system Increased business agility and operational efficiency by seamlessly integrating with the in-house, ERP system and embedding business processes into a single portal Boosted company revenue by enabling sales team members to submit print-advertising discount requests through mobile devices instead of waiting to return to office, ensuring timely approval from managers to meet tight publication deadlines Improved management decision-making by enabling employees to easily share and access feedback through opinion polls or forums, boosting staff morale Introduced the single sign-on capability and enhanced security by enabling managers to decide access level for staff members based on role or geographical location Reduced the need for staff training and minimized user resistance to systems by providing a dynamic and intuitive user experience Why Oracle JPL did not consider other products because the company was already using Oracle Database, Enterprise Edition with Real Application Clusters and had a positive experience with Oracle. JPL chose Oracle WebCenter Portal to ensure no compatibility issues for integration with its existing Oracle products and to take advantage of the experience and support of a reputable vendor to ensure business continuity. “We chose Oracle because we knew we could rely on its support and experience. In addition, Oracle WebCenter Portal’s speed, agility, and mobile access features were a perfect fit for our business requirements,” Bhatia said. Implementation Process JPL launched the enterprise portal to 500 users in the first phase of the project, and plans to extend this to 2,000 users when the portal is fully launched. Oracle partner PricewaterhouseCoopers used Oracle Application Development Framework for the intial set-up, user training and to develop and design sample workflows. JPL’s internal IT staff then took charge of the implementation, bringing it to completion on budget. Partner Oracle PartnerPricewaterhouseCoopers (India)

  Read the article

• EM12c Release 4: Database as a Service Enhancements

  - by Adeesh Fulay

  Oracle Enterprise Manager 12.1.0.4 (or simply put EM12c R4) is the latest update to the product. As previous versions, this release provides tons of enhancements and bug fixes, attributing to improved stability and quality. One of the areas that is most exciting and has seen tremendous growth in the last few years is that of Database as a Service. EM12c R4 provides a significant update to Database as a Service. The key themes are: Comprehensive Database Service Catalog (includes single instance, RAC, and Data Guard) Additional Storage Options for Snap Clone (includes support for Database feature CloneDB) Improved Rapid Start Kits Extensible Metering and Chargeback Miscellaneous Enhancements 1. Comprehensive Database Service Catalog Before we get deep into implementation of a service catalog, lets first understand what it is and what benefits it provides. Per ITIL, a service catalog is an exhaustive list of IT services that an organization provides or offers to its employees or customers. Service catalogs have been widely popular in the space of cloud computing, primarily as the medium to provide standardized and pre-approved service definitions. There is already some good collateral out there that talks about Oracle database service catalogs. The two whitepapers i recommend reading are: Service Catalogs: Defining Standardized Database Service High Availability Best Practices for Database Consolidation: The Foundation for Database as a Service [Oracle MAA] EM12c comes with an out-of-the-box service catalog and self service portal since release 1. For the customers, it provides the following benefits: Present a collection of standardized database service definitions, Define standardized pools of hardware and software for provisioning, Role based access to cater to different class of users, Automated procedures to provision the predefined database definitions, Setup chargeback plans based on service tiers and database configuration sizes, etc Starting Release 4, the scope of services offered via the service catalog has been expanded to include databases with varying levels of availability - Single Instance (SI) or Real Application Clusters (RAC) databases with multiple data guard based standby databases. Some salient points of the data guard integration: Standby pools can now be defined across different datacenters or within the same datacenter as the primary (this helps in modelling the concept of near and far DR sites) The standby databases can be single instance, RAC, or RAC One Node databases Multiple standby databases can be provisioned, where the maximum limit is determined by the version of database software The standby databases can be in either mount or read only (requires active data guard option) mode All database versions 10g to 12c supported (as certified with EM 12c) All 3 protection modes can be used - Maximum availability, performance, security Log apply can be set to sync or async along with the required apply lag The different service levels or service tiers are popularly represented using metals - Platinum, Gold, Silver, Bronze, and so on. The Oracle MAA whitepaper (referenced above) calls out the various service tiers as defined by Oracle's best practices, but customers can choose any logical combinations from the table below:  Primary  Standby [1 or more]  EM 12cR4  SI  -  SI  SI  RAC -  RAC SI  RAC RAC  RON -  RON RON where RON = RAC One Node is supported via custom post-scripts in the service template A sample service catalog would look like the image below. Here we have defined 4 service levels, which have been deployed across 2 data centers, and have 3 standardized sizes. Again, it is important to note that this is just an example to get the creative juices flowing. I imagine each customer would come up with their own catalog based on the application requirements, their RTO/RPO goals, and the product licenses they own. In the screenwatch titled 'Build Service Catalog using EM12c DBaaS', I walk through the complete steps required to setup this sample service catalog in EM12c. 2. Additional Storage Options for Snap Clone In my previous blog posts, i have described the snap clone feature in detail. Essentially, it provides a storage agnostic, self service, rapid, and space efficient approach to solving your data cloning problems. The net benefit is that you get incredible amounts of storage savings (on average 90%) all while cloning databases in a matter of minutes. Space and Time, two things enterprises would love to save on. This feature has been designed with the goal of providing data cloning capabilities while protecting your existing investments in server, storage, and software. With this in mind, we have pursued with the dual solution approach of Hardware and Software. In the hardware approach, we connect directly to your storage appliances and perform all low level actions required to rapidly clone your databases. While in the software approach, we use an intermediate software layer to talk to any storage vendor or any storage configuration to perform the same low level actions. Thus delivering the benefits of database thin cloning, without requiring you to drastically changing the infrastructure or IT's operating style. In release 4, we expand the scope of options supported by snap clone with the addition of database CloneDB. While CloneDB is not a new feature, it was first introduced in 11.2.0.2 patchset, it has over the years become more stable and mature. CloneDB leverages a combination of Direct NFS (or dNFS) feature of the database, RMAN image copies, sparse files, and copy-on-write technology to create thin clones of databases from existing backups in a matter of minutes. It essentially has all the traits that we want to present to our customers via the snap clone feature. For more information on cloneDB, i highly recommend reading the following sources: Blog by Tim Hall: Direct NFS (DNFS) CloneDB in Oracle Database 11g Release 2 Oracle OpenWorld Presentation by Cern: Efficient Database Cloning using Direct NFS and CloneDB The advantages of the new CloneDB integration with EM12c Snap Clone are: Space and time savings Ease of setup - no additional software is required other than the Oracle database binary Works on all platforms Reduce the dependence on storage administrators Cloning process fully orchestrated by EM12c, and delivered to developers/DBAs/QA Testers via the self service portal Uses dNFS to delivers better performance, availability, and scalability over kernel NFS Complete lifecycle of the clones managed by EM12c - performance, configuration, etc 3. Improved Rapid Start Kits DBaaS deployments tend to be complex and its setup requires a series of steps. These steps are typically performed across different users and different UIs. The Rapid Start Kit provides a single command solution to setup Database as a Service (DBaaS) and Pluggable Database as a Service (PDBaaS). One command creates all the Cloud artifacts like Roles, Administrators, Credentials, Database Profiles, PaaS Infrastructure Zone, Database Pools and Service Templates. Once the Rapid Start Kit has been successfully executed, requests can be made to provision databases and PDBs from the self service portal. Rapid start kit can create complex topologies involving multiple zones, pools and service templates. It also supports standby databases and use of RMAN image backups. The Rapid Start Kit in reality is a simple emcli script which takes a bunch of xml files as input and executes the complete automation in a matter of seconds. On a full rack Exadata, it took only 40 seconds to setup PDBaaS end-to-end. This kit works for both Oracle's engineered systems like Exadata, SuperCluster, etc and also on commodity hardware. One can draw parallel to the Exadata One Command script, which again takes a bunch of inputs from the administrators and then runs a simple script that configures everything from network to provisioning the DB software. Steps to use the kit: The kit can be found under the SSA plug-in directory on the OMS: EM_BASE/oracle/MW/plugins/oracle.sysman.ssa.oms.plugin_12.1.0.8.0/dbaas/setup It can be run from this default location or from any server which has emcli client installed For most scenarios, you would use the script dbaas/setup/database_cloud_setup.py For Exadata, special integration is provided to reduce the number of inputs even further. The script to use for this scenario would be dbaas/setup/exadata_cloud_setup.py The database_cloud_setup.py script takes two inputs: Cloud boundary xml: This file defines the cloud topology in terms of the zones and pools along with host names, oracle home locations or container database names that would be used as infrastructure for provisioning database services. This file is optional in case of Exadata, as the boundary is well know via the Exadata system target available in EM. Input xml: This file captures inputs for users, roles, profiles, service templates, etc. Essentially, all inputs required to define the DB services and other settings of the self service portal. Once all the xml files have been prepared, invoke the script as follows for PDBaaS: emcli @database_cloud_setup.py -pdbaas -cloud_boundary=/tmp/my_boundary.xml -cloud_input=/tmp/pdb_inputs.xml          The script will prompt for passwords a few times for key users like sysman, cloud admin, SSA admin, etc. Once complete, you can simply log into EM as the self service user and request for databases from the portal. More information available in the Rapid Start Kit chapter in Cloud Administration Guide.  4. Extensible Metering and Chargeback  Last but not the least, Metering and Chargeback in release 4 has been made extensible in all possible regards. The new extensibility features allow customer, partners, system integrators, etc to : Extend chargeback to any target type managed in EM Promote any metric in EM as a chargeback entity Extend list of charge items via metric or configuration extensions Model abstract entities like no. of backup requests, job executions, support requests, etc  A slew of emcli verbs have also been added that allows administrators to create, edit, delete, import/export charge plans, and assign cost centers all via the command line. More information available in the Chargeback API chapter in Cloud Administration Guide. 5. Miscellaneous Enhancements There are other miscellaneous, yet important, enhancements that are worth a mention. These mostly have been asked by customers like you. These are: Custom naming of DB Services Self service users can provide custom names for DB SID, DB service, schemas, and tablespaces Every custom name is validated for uniqueness in EM 'Create like' of Service Templates Now creating variants of a service template is only a click away. This would be vital when you publish service templates to represent different database sizes or service levels. Profile viewer View the details of a profile like datafile, control files, snapshot ids, export/import files, etc prior to its selection in the service template Cleanup automation - for failed and successful requests Single emcli command to cleanup all remnant artifacts of a failed request Cleanup can be performed on a per request bases or by the entire pool As an extension, you can also delete successful requests Improved delete user workflow Allows administrators to reassign cloud resources to another user or delete all of them Support for multiple tablespaces for schema as a service In addition to multiple schemas, user can also specify multiple tablespaces per request I hope this was a good introduction to the new Database as a Service enhancements in EM12c R4. I encourage you to explore many of these new and existing features and give us feedback. Good luck! References: Cloud Management Page on OTN Cloud Administration Guide [Documentation] -- Adeesh Fulay (@adeeshf)

  Read the article

• Big GRC: Turning Data into Actionable GRC Intelligence

  - by Jenna Danko

  While it’s no longer headline news that Governments have carried out large scale data-mining programmes aimed at terrorism detection and identifying other patterns of interest across a wide range of digital data sources, the debate over the ethics and justification over this action, will clearly continue for some time to come. What is becoming clear is that these programmes are a framework for the collation and aggregation of massive amounts of unstructured data and from this, the creation of actionable intelligence from analyses that allowed the analysts to explore and extract a variety of patterns and then direct resources. This data included audio and video chats, phone calls, photographs, e-mails, documents, internet searches, social media posts and mobile phone logs and connections. Although Governance, Risk and Compliance (GRC) professionals are not looking at the implementation of such programmes, there are many similar GRC “Big data” challenges to be faced and potential lessons to be learned from these high profile government programmes that can be applied a lot closer to home. For example, how can GRC professionals collect, manage and analyze an enormous and disparate volume of data to create and manage their own actionable intelligence covering hidden signs and patterns of criminal activity, the early or retrospective, violation of regulations/laws/corporate policies and procedures, emerging risks and weakening controls etc. Not exactly the stuff of James Bond to be sure, but it is certainly more applicable to most GRC professional’s day to day challenges. So what is Big Data and how can it benefit the GRC process? Although it often varies, the definition of Big Data largely refers to the following types of data: Traditional Enterprise Data – includes customer information from CRM systems, transactional ERP data, web store transactions, and general ledger data. Machine-Generated /Sensor Data – includes Call Detail Records (“CDR”), weblogs and trading systems data. Social Data – includes customer feedback streams, micro-blogging sites like Twitter, and social media platforms like Facebook. The McKinsey Global Institute estimates that data volume is growing 40% per year, and will grow 44x between 2009 and 2020. But while it’s often the most visible parameter, volume of data is not the only characteristic that matters. In fact, according to sources such as Forrester there are four key characteristics that define big data: Volume. Machine-generated data is produced in much larger quantities than non-traditional data. This is all the data generated by IT systems that power the enterprise. This includes live data from packaged and custom applications – for example, app servers, Web servers, databases, networks, virtual machines, telecom equipment, and much more. Velocity. Social media data streams – while not as massive as machine-generated data – produce a large influx of opinions and relationships valuable to customer relationship management as well as offering early insight into potential reputational risk issues. Even at 140 characters per tweet, the high velocity (or frequency) of Twitter data ensures large volumes (over 8 TB per day) need to be managed. Variety. Traditional data formats tend to be relatively well defined by a data schema and change slowly. In contrast, non-traditional data formats exhibit a dizzying rate of change. Without question, all GRC professionals work in a dynamic environment and as new services, new products, new business lines are added or new marketing campaigns executed for example, new data types are needed to capture the resultant information.  Value. The economic value of data varies significantly. Typically, there is good information hidden amongst a larger body of non-traditional data that GRC professionals can use to add real value to the organisation; the greater challenge is identifying what is valuable and then transforming and extracting that data for analysis and action. For example, customer service calls and emails have millions of useful data points and have long been a source of information to GRC professionals. Those calls and emails are critical in helping GRC professionals better identify hidden patterns and implement new policies that can reduce the amount of customer complaints.   Now on a scale and depth far beyond those in place today, all that unstructured call and email data can be captured, stored and analyzed to reveal the reasons for the contact, perhaps with the aggregated customer results cross referenced against what is being said about the organization or a similar peer organization on social media. The organization can then take positive actions, communicating to the market in advance of issues reaching the press, strengthening controls, adjusting risk profiles, changing policy and procedures and completely minimizing, if not eliminating, complaints and compensation for that specific reason in the future. In this one example of many similar ones, the GRC team(s) has demonstrated real and tangible business value. Big Challenges - Big Opportunities As pointed out by recent Forrester research, high performing companies (those that are growing 15% or more year-on-year compared to their peers) are taking a selective approach to investing in Big Data.  "Tomorrow's winners understand this, and they are making selective investments aimed at specific opportunities with tangible benefits where big data offers a more economical solution to meet a need." (Forrsights Strategy Spotlight: Business Intelligence and Big Data, Q4 2012) As pointed out earlier, with the ever increasing volume of regulatory demands and fines for getting it wrong, limited resource availability and out of date or inadequate GRC systems all contributing to a higher cost of compliance and/or higher risk profile than desired – a big data investment in GRC clearly falls into this category. However, to make the most of big data organizations must evolve both their business and IT procedures, processes, people and infrastructures to handle these new high-volume, high-velocity, high-variety sources of data and be able integrate them with the pre-existing company data to be analyzed. GRC big data clearly allows the organization access to and management over a huge amount of often very sensitive information that although can help create a more risk intelligent organization, also presents numerous data governance challenges, including regulatory compliance and information security. In addition to client and regulatory demands over better information security and data protection the sheer amount of information organizations deal with the need to quickly access, classify, protect and manage that information can quickly become a key issue  from a legal, as well as technical or operational standpoint. However, by making information governance processes a bigger part of everyday operations, organizations can make sure data remains readily available and protected. The Right GRC & Big Data Partnership Becomes Key  The "getting it right first time" mantra used in so many companies remains essential for any GRC team that is sponsoring, helping kick start, or even overseeing a big data project. To make a big data GRC initiative work and get the desired value, partnerships with companies, who have a long history of success in delivering successful GRC solutions as well as being at the very forefront of technology innovation, becomes key. Clearly solutions can be built in-house more cheaply than through vendor, but as has been proven time and time again, when it comes to self built solutions covering AML and Fraud for example, few have able to scale or adapt appropriately to meet the changing regulations or challenges that the GRC teams face on a daily basis. This has led to the creation of GRC silo’s that are causing so many headaches today. The solutions that stand out and should be explored are the ones that can seamlessly merge the traditional world of well-known data, analytics and visualization with the new world of seemingly innumerable data sources, utilizing Big Data technologies to generate new GRC insights right across the enterprise.Ultimately, Big Data is here to stay, and organizations that embrace its potential and outline a viable strategy, as well as understand and build a solid analytical foundation, will be the ones that are well positioned to make the most of it. A Blueprint and Roadmap Service for Big Data Big data adoption is first and foremost a business decision. As such it is essential that your partner can align your strategies, goals, and objectives with an architecture vision and roadmap to accelerate adoption of big data for your environment, as well as establish practical, effective governance that will maintain a well managed environment going forward. Key Activities: While your initiatives will clearly vary, there are some generic starting points the team and organization will need to complete: Clearly define your drivers, strategies, goals, objectives and requirements as it relates to big data Conduct a big data readiness and Information Architecture maturity assessment Develop future state big data architecture, including views across all relevant architecture domains; business, applications, information, and technology Provide initial guidance on big data candidate selection for migrations or implementation Develop a strategic roadmap and implementation plan that reflects a prioritization of initiatives based on business impact and technology dependency, and an incremental integration approach for evolving your current state to the target future state in a manner that represents the least amount of risk and impact of change on the business Provide recommendations for practical, effective Data Governance, Data Quality Management, and Information Lifecycle Management to maintain a well-managed environment Conduct an executive workshop with recommendations and next steps There is little debate that managing risk and data are the two biggest obstacles encountered by financial institutions.  Big data is here to stay and risk management certainly is not going anywhere, and ultimately financial services industry organizations that embrace its potential and outline a viable strategy, as well as understand and build a solid analytical foundation, will be best positioned to make the most of it. Matthew Long is a Financial Crime Specialist for Oracle Financial Services. He can be reached at matthew.long AT oracle.com.

  Read the article

• Slow boot on Ubuntu 12.04, probable cause the network connection

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• CodePlex Daily Summary for Friday, December 14, 2012

  CodePlex Daily Summary for Friday, December 14, 2012Popular ReleasesCommand Line Parser Library: 1.9.3.31 rc0: Main assembly CommandLine.dll signed. Removed old commented code. Added missing XML documentation comments. Two (very) minor code refactoring changes.BlackJumboDog: Ver5.7.4: 2012.12.13 Ver5.7.4 (1)Web???????、???????????????????????????????????????????VFPX: ssClasses A1.0: My initial release. See https://vfpx.codeplex.com/wikipage?title=ssClasses&referringTitle=Home for a brief description of what is inside this releasesb0t v.5: sb0t 5.01 alpha 1: GUI support for Spanish language (Thank you Di3go and Oysterhead) Captcha database updates Bug fix where some hosts could not joinHome Access Plus+: v8.6: v8.6.1213.1220 Added: Group look up to the visible property of the Booking System Fixed: Switched to using the outlook/exchange thumbnailPhoto instead of jpegPhoto Added: Add a blank paragraph below the tiles. This means that the browser displays a vertical scroller when resizing the window. Previously it was possible for the bottom edge of a tile not to be visible if the browser window was resized. Added: Booking System: Only Display Day+Month on the booking Home Page. This allows for the cs...Layered Architecture Solution Guidance (LASG): LASG 1.0.0.8 for Visual Studio 2012: PRE-REQUISITES Open GAX (Please install Oct 4, 2012 version) Microsoft® System CLR Types for Microsoft® SQL Server® 2012 Microsoft® SQL Server® 2012 Shared Management Objects Microsoft Enterprise Library 5.0 (for the generated code) Windows Azure SDK (for layered cloud applications) Silverlight 5 SDK (for Silverlight applications) THE RELEASE This release only works on Visual Studio 2012. Known Issue If you choose the Database project, the solution unfolding time will be slow....Fiskalizacija za developere: FiskalizacijaDev 2.0: Prva prava produkcijska verzija - Zakon je tu, ova je verzija uskladena sa trenutno važecom Tehnickom specifikacijom (v1.2. od 04.12.2012.) i spremna je za produkcijsko korištenje. Verzije iza ove ce ovisiti o naknadnim izmjenama Zakona i/ili Tehnicke specifikacije, odnosno, o eventualnim greškama u radu/zahtjevima community-a za novim feature-ima. Novosti u v2.0 su: - That assembly does not allow partially trusted callers (http://fiskalizacija.codeplex.com/workitem/699) - scheme IznosType...Simple Injector: Simple Injector v1.6.1: This patch release fixes a bug in the integration libraries that disallowed the application to start when .NET 4.5 was not installed on the machine (but only .NET 4.0). The following packages are affected: SimpleInjector.Integration.Web.dll SimpleInjector.Integration.Web.Mvc.dll SimpleInjector.Integration.Wcf.dll SimpleInjector.Extensions.LifetimeScoping.dllBootstrap Helpers: Version 1: First releasesheetengine - Isometric HTML5 JavaScript Display Engine: sheetengine v1.2.0: Main featuresOptimizations for intersectionsThe main purpose of this release was to further optimize rendering performance by skipping object intersections with other sheets. From now by default an object's sheets will only intersect its own sheets and never other static or dynamic sheets. This is the usual scenario since objects will never bump into other sheets when using collision detection. DocumentationMany of you have been asking for proper documentation, so here it goes. Check out the...DirectX Tool Kit: December 11, 2012: December 11, 2012 Ex versions of DDSTextureLoader and WICTextureLoader Removed use of ATL's CComPtr in favor of WRL's ComPtr for all platforms to support VS Express editions Updated VS 2010 project for official 'property sheet' integration for Windows 8.0 SDK Minor fix to CommonStates for Feature Level 9.1 Tweaked AlphaTestEffect.cpp to work around ARM NEON compiler codegen bug Added dxguid.lib as a default library for Debug builds to resolve GUID link issuesDNN Flash Viewer: Source (same as default release): SourceArcGIS Editor for OpenStreetMap: ArcGIS Editor for OSM 2.1 Final for 10.1: We are proud to announce the release of ArcGIS Editor for OpenStreetMap version 2.1. This download is compatible with ArcGIS 10.1, and includes setups for the Desktop Component, Desktop Component when 64 bit Background Geoprocessing is installed, and the Server Component. Important: if you already have ArcGIS Editor for OSM installed but want to install this new version, you will need to uninstall your previous version and then install this one. This release includes support for the ArcGIS 1...SharpCompress - a fully native C# library for RAR, 7Zip, Zip, Tar, GZip, BZip2: SharpCompress 0.8.2: This release just contains some fixes that have been done since the last release. Plus, this is strong named as well. I apologize for the lack of updates but my free time is less these days.Media Companion: MediaCompanion3.511b release: Two more bug fixes: - General Preferences were not getting restored - Fanart and poster image files were being locked, preventing changes to themVodigi Open Source Interactive Digital Signage: Vodigi Release 5.5: The following enhancements and fixes are included in Vodigi 5.5. Vodigi Administrator - Manage Music Files - Add Music Files to Image Slide Shows - Manage System Messages - Display System Messages to Users During Login - Ported to Visual Studio 2012 and MVC 4 - Added New Vodigi Administrator User Guide Vodigi Player - Improved Login/Schedule Startup Procedure - Startup Using Last Known Schedule when Disconnected on Startup - Improved Check for Schedule Changes - Now Every 15 Minutes - Pla...VidCoder: 1.4.10 Beta: Added progress percent to the title bar/task bar icon. Added MPLS information to Blu-ray titles. Fixed the following display issues in Windows 8: Uncentered text in textbox controls Disabled controls not having gray text making them hard to identify as disabled Drop-down menus having hard-to distinguish white on light-blue text Added more logging to proxy disconnect issues and increased timeout on initial call to help prevent timeouts. Fixed encoding window showing the built-in pre...WPF Application Framework (WAF): WPF Application Framework (WAF) 2.5.0.400: Version 2.5.0.400 (Release): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Changelog Legend: [B] Breaking change; [O] Marked member as obsolete Update the documentation. InfoMan: Write the documentation. Other Downloads Downloads OverviewBee OPOA Platform: Bee OPOA Demo V1.0.001: Initial version.Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.78: Fix for issue #18924 - using -pretty option left in ///#DEBUG blocks. Fix for issue #18980 - bad += optimization caused bug in resulting code. Optimization has been removed pending further review.New Projects.net demo: This is a demo project. 12141325: tesing12141327: testingAW User Applications: This project is used to enable AccessWeb User Applications for Database Application Users. Outline: The degree of professionalism permissions access options OkBattery Life Live Tile: Windows 8 app that displays the battery percentage in a live tile on the homescreen with the help of a system tray application. only available on intel devices.CMS .NET: CMS .net HTML5 multilingual+FORUM+GALLERY+Responsive Web Design+WIKI+COMMUNITY: Easy user-friendly, fast 10X,;multi site in different domain; multi servercookieTerm: A simple BBS terminal that can run in unicode environmentDevCow: This is a location for all of the community projects that help support DevCow.comDevville.NET: The project contains some of a very useful helpers and extension methods for .NET and SharePoint.Echo Garden: Echo Garden is a modification of Alphalabs' Windows Phone app, Node Garden, that represents the nodes through sound.FluentNavigationCoercion: Simple library that makes navigation coercion on WP simple and readableGet Music: Internet radio's parser. Parse radio logs, store received data to store. Make statistic analyze of radio. jKinect - Kinectify any web site.: Provide a unique Kinect User Experience for your website. With jKinect, turn any web site into a Kinect enabled web application.Lagos Single Mothers: This is a web2.0 site that will help single mothers in the city of Lagos (in Nigeria) share ideas on how to raise children, as single mothers. LIF11: Projet logique classiqueMalkiSum: Malki SumMyLittleAdressBook: Just a little project to test MVVM pattern on a multiview solution with authentificationNopCommerce 2.7x Multi Store version: NopCommerce 7.x Multi Store / Vendor versionPodcastToMp3: Automated tool to make MP3s from M4A chapters.Primer Demo ClickOnce: Demo ClickOncePulsus: A simple .NET logging library for modern applications.Sharp6800 - ET-3400 Microprocessor Trainer Emulator: A Heathkit ET-3400 Microprocessor Trainer Emulator. It features a 6800 emulator core and simulated 7-segment display and keypad. Written in 100% C#TEdit: TEdit is a source code editor that mainly used for InfoBasic Programming language. Running in Windows platform. Developed using Scintilla & ScintillaNet.VsPackageUtils: VsPackageUtils is a basic utility helper class for common operations in a VsPackage.WiFiShare: WiFiShare shares your LAN connection to WiFi using Internet Connection Sharing(ICS) from your Windows operating system.Windows 8 RSS App Kit: A Windows 8 App "kit" that allows you to build a fixed-list RSS reader with auto-image-detection in feeds.

  Read the article

• Building Enterprise Smartphone App &ndash; Part 4: Application Development Considerations

  - by Tim Murphy

  This is the final part in a series of posts based on a talk I gave recently at the Chicago Information Technology Architects Group.  Feel free to leave feedback. Application Development Considerations Now we get to the actual building of your solutions.  What are the skills and resources that will be needed in order to develop a smartphone application in the enterprise? Language Knowledge One of the first things you need to consider when you are deciding which platform language do you either have the most in house skill base or can you easily acquire.  If you already have developers who know Java or C# you may want to use either Android or Windows Phone.  You should also take into consideration the market availability of developers.  If your key developer leaves how easy is it to find a knowledgeable replacement? A second consideration when it comes to programming languages is the qualities exposed by the languages of a particular platform.  How well does that development language and its associated frameworks support things like security and access to the features of the smartphone hardware?  This will play into your overall cost of ownership if you have to create this infrastructure on your own. Manage Limited Resources Everything is limited on a smartphone: battery, memory, processing power, network bandwidth.  When developing your applications you will have to keep your footprint as small as possible in every way.  This means not running unnecessary processes in the background that will drain the battery or pulling more data over the airwaves than you have to.  You also want to keep your on device in as compact a format as possible. Mobile Design Patterns There are a number of design patterns that have either come to life because of smartphone development or have been adapted for this use.  The main pattern in the Windows Phone environment is the MVVM (Model-View-View-Model).  This is great for overall application structure and separation of concerns.  The fun part is trying to keep that separation as pure as possible.  Many of the other patterns may or may not have strict definitions, but some that you need to be concerned with are push notification, asynchronous communication and offline data storage. Real estate is limited on smartphones and even tablets. You are also limited in the type of controls that can be represented in the UI. This means rethinking how you modularize your application. Typing is also much harder to do so you want to reduce this as much as possible.  This leads to UI patterns.  While not what we would traditionally think of as design patterns the guidance each platform has for UI design is critical to the success of your application.  If user find the application difficult navigate they will not use it. Development Process Because of the differences in development tools required, test devices and certification and deployment processes your teams will need to learn new way of working together.  This will include the need to integrate service contracts of back-end systems with mobile applications.  You will also want to make sure that you present consistency across different access points to corporate data.  Your web site may have more functionality than your smartphone application, but it should have a consistent core set of functionality.  This all requires greater communication between sub-teams of your developers. Testing Process Testing of smartphone apps has a lot more to do with what happens when you lose connectivity or if the user navigates away from your application. There are a lot more opportunities for the user or the device to perform disruptive acts.  This should be your main testing concentration aside from the main business requirements.  You will need to do things like setting the phone to airplane mode and seeing what the application does in order to weed out any gaps in your handling communication interruptions. Need For Outside Experts Since this is a development area that is new to most companies the need for experts is a lot greater. Whether these are consultants, vendor representatives or just development community forums you will need to establish expert contacts. Nothing is more dangerous for your project timelines than a lack of knowledge.  Make sure you know who to call to avoid lengthy delays in your project because of knowledge gaps. Security Security has to be a major concern for enterprise applications. You aren't dealing with just someone's game standings. You are dealing with a companies intellectual property and competitive advantage. As such you need to start by limiting access to the application itself.  Once the user is in the app you need to ensure that the data is secure at all times.  This includes both local storage and across the wire.  This means if a platform doesn’t natively support encryption for these functions you will need to find alternatives to secure your data.  You also need to keep secret (encryption) keys obfuscated or locked away outside of the application. People can disassemble the code otherwise and break your encryption. Offline Capabilities As we discussed earlier one your biggest concerns is not having connectivity.  Because of this a good portion of your code may be dedicated to handling loss of connection and reconnection situations.  What do you do if you lose the network?  Back up all your transactions and store of any supporting data so that operations can continue off line. In order to support this you will need to determine the available flat file or local data base capabilities of the platform.  Any failed transactions will need to support a retry mechanism whether it is automatic or user initiated.  This also includes your services since they will need to be able to roll back partially completed transactions.  What ever you do, don’t ignore this area when you are designing your system. Deployment Each platform has different deployment capabilities. Some are more suited to enterprise situations than others. Apple's approach is probably the most mature at the moment. Prior to the current generation of smartphone platforms it would have been Windows CE. Windows Phone 7 has the limitation that the app has to be distributed through the same network as public facing applications. You mark them as private which means that they are only accessible by a direct URL. Unfortunately this does not make them undiscoverable (although it is very difficult). This will change with Windows Phone 8 where companies will be able to certify their own applications and distribute them.  Given this Windows Phone applications need to be more diligent with application access in order to keep them restricted to the company's employees. My understanding of the Android deployment schemes is that it is much less standardized then either iOS or Windows Phone. Someone would have to confirm or deny that for me though since I have not yet put the time into researching this platform further. Given my limited exposure to the iOS and Android platforms I have not been able to confirm this, but there are varying degrees of user involvement to install and keep applications updated. At one extreme the user just goes to a website to do the install and in other case they may need to download files and perform steps to install them. Future Bluetooth Today we use Bluetooth for keyboards, mice and headsets.  In the future it could be used to interrogate car computers or manufacturing systems or possibly retail machines by service techs.  This would open smartphones to greater use as a almost a Star Trek Tricorder.  You would get you all your data as well as being able to use it as a universal remote for just about any device or machine. Better corporation controlled deployment At least in the Windows Phone world the upcoming release of Windows Phone 8 will include a private certification and deployment option that is currently not available with Windows Phone 7 (Mango). We currently have to run the apps through the Marketplace certification process and use a targeted distribution method. Platform independent approaches HTML5 and JavaScript with Web Service has become a popular topic lately for not only creating flexible web site, but also creating cross platform mobile applications.  I’m not yet convinced that this lowest common denominator approach is viable in most cases, but it does have it’s place and seems to be growing.  Be sure to keep an eye on it. Summary From my perspective enterprise smartphone applications can offer a great competitive advantage to many companies.  They are not cheap to build and should be approached cautiously.  Understand the factors I have outlined in this series, do you due diligence and see if there is a portion of your business that can benefit from the mobile experience. del.icio.us Tags: Architecture,Smartphones,Windows Phone,iOS,Android

  Read the article

• Recursion in Ecore-File?!

  - by Dominik

  Hey guys, just tried to convert towards a Ecore-Model from a given UML-Model. After this I am trying to create a Generator Model. Everytime I try to do this I get the Error Message, that there is a "Unhandled event loop exception" with this log: org.eclipse.swt.SWTException: Failed to execute runnable (java.lang.NullPointerException) at org.eclipse.swt.SWT.error(SWT.java:3884) at org.eclipse.swt.SWT.error(SWT.java:3799) at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:137) at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3885) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3506) at org.eclipse.jface.window.Window.runEventLoop(Window.java:825) at org.eclipse.jface.window.Window.open(Window.java:801) at org.eclipse.gmf.internal.bridge.ui.dashboard.DashboardMediator$RunWizardAction.run(DashboardMediator.java:316) at org.eclipse.gmf.internal.bridge.ui.dashboard.HyperlinkFigure$1.mousePressed(HyperlinkFigure.java:63) at org.eclipse.draw2d.Figure.handleMousePressed(Figure.java:873) at org.eclipse.draw2d.SWTEventDispatcher.dispatchMousePressed(SWTEventDispatcher.java:214) at org.eclipse.draw2d.LightweightSystem$EventHandler.mouseDown(LightweightSystem.java:513) at org.eclipse.swt.widgets.TypedListener.handleEvent(TypedListener.java:179) at org.eclipse.swt.widgets.EventTable.sendEvent(EventTable.java:84) at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1003) at org.eclipse.swt.widgets.Display.runDeferredEvents(Display.java:3910) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3503) at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2405) at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2369) at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2221) at org.eclipse.ui.internal.Workbench$5.run(Workbench.java:500) at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332) at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:493) at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149) at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:113) at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:194) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:368) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:559) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:514) at org.eclipse.equinox.launcher.Main.run(Main.java:1311) Caused by: java.lang.NullPointerException at org.eclipse.emf.converter.util.ConverterUtil.computeRequiredPackages(ConverterUtil.java:374) at org.eclipse.emf.converter.ui.contribution.base.ModelConverterPackagePage.validate(ModelConverterPackagePage.java:965) at org.eclipse.emf.importer.ui.contribution.base.ModelImporterPackagePage.validate(ModelImporterPackagePage.java:101) at org.eclipse.emf.converter.ui.contribution.base.ModelConverterPackagePage$1.run(ModelConverterPackagePage.java:155) at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35) at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:134) ... 34 more After this there occurs another exception with this text: "Unable to create editor ID org.eclipse.emf.codegen.ecore.genmodel.presentation.GenModelEditorID:An unexpected exception was thrown." The session data says: eclipse.buildId=unknown java.version=1.6.0_13 java.vendor=Sun Microsystems Inc. BootLoader constants: OS=win32, ARCH=x86, WS=win32, NL=de_DE Framework arguments: -product org.eclipse.epp.package.modeling.product Command-line arguments: -os win32 -ws win32 -arch x86 -product org.eclipse.epp.package.modeling.product -consoleLog With this long log: java.lang.NullPointerException at org.eclipse.emf.ecore.util.EcoreUtil.getURI(EcoreUtil.java:2887) at org.eclipse.emf.codegen.ecore.genmodel.impl.GenModelImpl.diagnose(GenModelImpl.java:2930) at org.eclipse.emf.codegen.ecore.genmodel.presentation.GenModelEditor.validate(GenModelEditor.java:1773) at org.eclipse.emf.codegen.ecore.genmodel.presentation.GenModelEditor.initialize(GenModelEditor.java:596) at org.eclipse.emf.codegen.ecore.genmodel.presentation.GenModelEditor.createPages(GenModelEditor.java:1080) at org.eclipse.ui.part.MultiPageEditorPart.createPartControl(MultiPageEditorPart.java:357) at org.eclipse.ui.internal.EditorReference.createPartHelper(EditorReference.java:662) at org.eclipse.ui.internal.EditorReference.createPart(EditorReference.java:462) at org.eclipse.ui.internal.WorkbenchPartReference.getPart(WorkbenchPartReference.java:595) at org.eclipse.ui.internal.EditorReference.getEditor(EditorReference.java:286) at org.eclipse.ui.internal.WorkbenchPage.busyOpenEditorBatched(WorkbenchPage.java:2857) at org.eclipse.ui.internal.WorkbenchPage.busyOpenEditor(WorkbenchPage.java:2762) at org.eclipse.ui.internal.WorkbenchPage.access$11(WorkbenchPage.java:2754) at org.eclipse.ui.internal.WorkbenchPage$10.run(WorkbenchPage.java:2705) at org.eclipse.swt.custom.BusyIndicator.showWhile(BusyIndicator.java:70) at org.eclipse.ui.internal.WorkbenchPage.openEditor(WorkbenchPage.java:2701) at org.eclipse.ui.internal.WorkbenchPage.openEditor(WorkbenchPage.java:2685) at org.eclipse.ui.internal.WorkbenchPage.openEditor(WorkbenchPage.java:2668) at org.eclipse.emf.converter.ui.contribution.base.ModelConverterWizard.openEditor(ModelConverterWizard.java:318) at org.eclipse.emf.importer.ui.contribution.base.ModelImporterWizard.performFinish(ModelImporterWizard.java:167) at org.eclipse.jface.wizard.WizardDialog.finishPressed(WizardDialog.java:752) at org.eclipse.gmf.internal.bridge.ui.dashboard.DashboardMediator$RunWizardAction$1.finishPressed(DashboardMediator.java:311) at org.eclipse.jface.wizard.WizardDialog.buttonPressed(WizardDialog.java:373) at org.eclipse.jface.dialogs.Dialog$2.widgetSelected(Dialog.java:624) at org.eclipse.swt.widgets.TypedListener.handleEvent(TypedListener.java:228) at org.eclipse.swt.widgets.EventTable.sendEvent(EventTable.java:84) at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1003) at org.eclipse.swt.widgets.Display.runDeferredEvents(Display.java:3910) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3503) at org.eclipse.jface.window.Window.runEventLoop(Window.java:825) at org.eclipse.jface.window.Window.open(Window.java:801) at org.eclipse.gmf.internal.bridge.ui.dashboard.DashboardMediator$RunWizardAction.run(DashboardMediator.java:316) at org.eclipse.gmf.internal.bridge.ui.dashboard.HyperlinkFigure$1.mousePressed(HyperlinkFigure.java:63) at org.eclipse.draw2d.Figure.handleMousePressed(Figure.java:873) at org.eclipse.draw2d.SWTEventDispatcher.dispatchMousePressed(SWTEventDispatcher.java:214) at org.eclipse.draw2d.LightweightSystem$EventHandler.mouseDown(LightweightSystem.java:513) at org.eclipse.swt.widgets.TypedListener.handleEvent(TypedListener.java:179) at org.eclipse.swt.widgets.EventTable.sendEvent(EventTable.java:84) at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1003) at org.eclipse.swt.widgets.Display.runDeferredEvents(Display.java:3910) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3503) at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2405) at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2369) at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2221) at org.eclipse.ui.internal.Workbench$5.run(Workbench.java:500) at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332) at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:493) at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149) at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:113) at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:194) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:368) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:559) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:514) at org.eclipse.equinox.launcher.Main.run(Main.java:1311) Has anyone an idea what is going wrong? I looked a while at my model but were not able to find something wrong. I just thought there might be a recursion due to the "Unhandled event loop exception" but is this even possible? Thanks in advance, Dominik

  Read the article

• Having problems using haml and rails3

  - by Victor Rodrigues

  After installing rails3, I'm experiencing problems when trying to use haml with it. I have the updated gem installed, and after rails PROJECT_NAME , I did haml --rails in its root. It apparently had worked fine, since I have haml folder inside plugins, init.rb, as expected. But when I try to rake, or rails server, I get: rake aborted! no such file to load -- haml With --trace I get this: ** Invoke default (first_time) ** Invoke test (first_time) ** Execute test ** Invoke test:units (first_time) ** Invoke db:test:prepare (first_time) ** Invoke db:abort_if_pending_migrations (first_time) ** Invoke environment (first_time) ** Execute environment rake aborted! no such file to load -- haml /usr/local/lib/ruby/gems/1.8/gems/activesupport-3.0.0.beta/lib/active_support/dependencies.rb:167:in `require' /usr/local/lib/ruby/gems/1.8/gems/activesupport-3.0.0.beta/lib/active_support/dependencies.rb:167:in `require' /usr/local/lib/ruby/gems/1.8/gems/activesupport-3.0.0.beta/lib/active_support/dependencies.rb:537:in `new_constants_in' /usr/local/lib/ruby/gems/1.8/gems/activesupport-3.0.0.beta/lib/active_support/dependencies.rb:167:in `require' RAILS_PROJECT_ROOT/vendor/plugins/haml/init.rb:5 /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/plugin.rb:49 /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/initializable.rb:25:in `instance_exec' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/initializable.rb:25:in `run' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/initializable.rb:55:in `run_initializers' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/initializable.rb:54:in `each' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/initializable.rb:54:in `run_initializers' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/application.rb:71:in `initialize!' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/application.rb:112:in `initialize_tasks' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `call' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `execute' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `each' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `execute' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:597:in `invoke_with_call_chain' /usr/local/lib/ruby/1.8/monitor.rb:242:in `synchronize' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_chain' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:607:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `each' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:596:in `invoke_with_call_chain' /usr/local/lib/ruby/1.8/monitor.rb:242:in `synchronize' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_chain' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:607:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `each' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:596:in `invoke_with_call_chain' /usr/local/lib/ruby/1.8/monitor.rb:242:in `synchronize' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_chain' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:607:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `each' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:596:in `invoke_with_call_chain' /usr/local/lib/ruby/1.8/monitor.rb:242:in `synchronize' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_chain' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:583:in `invoke' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/test_unit/testing.rake:45 /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/test_unit/testing.rake:43:in `collect' /usr/local/lib/ruby/gems/1.8/gems/railties-3.0.0.beta/lib/rails/test_unit/testing.rake:43 /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `call' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `execute' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `each' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `execute' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:597:in `invoke_with_call_chain' /usr/local/lib/ruby/1.8/monitor.rb:242:in `synchronize' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_chain' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:607:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `each' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:604:in `invoke_prerequisites' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:596:in `invoke_with_call_chain' /usr/local/lib/ruby/1.8/monitor.rb:242:in `synchronize' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_chain' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:583:in `invoke' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2051:in `invoke_task' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `each' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exception_handling' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2023:in `top_level' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2001:in `run' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exception_handling' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:1998:in `run' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/bin/rake:31 /usr/local/bin/rake:19:in `load' /usr/local/bin/rake:19

  Read the article

• How do I get spring to inject my EntityManager?

  - by Trampas Kirk

  I'm following the guide here, but when the DAO executes, the EntityManager is null. I've tried a number of fixes I found in the comments on the guide, on various forums, and here (including this), to no avail. No matter what I seem to do the EntityManager remains null. Here are the relevant files, with packages etc changed to protect the innocent. spring-context.xml <?xml version="1.0" encoding="UTF-8"?> <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:tx="http://www.springframework.org/schema/tx" xmlns:context="http://www.springframework.org/schema/context" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans.xsd http://www.springframework.org/schema/tx http://www.springframework.org/schema/tx/spring-tx.xsd http://www.springframework.org/schema/context http://www.springframework.org/schema/context/spring-context.xsd" xmlns:p="http://www.springframework.org/schema/p"> <context:component-scan base-package="com.group.server"/> <context:annotation-config/> <tx:annotation-driven/> <bean id="propertyPlaceholderConfigurer" class="com.group.DecryptingPropertyPlaceholderConfigurer" p:systemPropertiesModeName="SYSTEM_PROPERTIES_MODE_OVERRIDE"> <property name="locations"> <list> <value>classpath*:spring-*.properties</value> <value>classpath*:${application.environment}.properties</value> </list> </property> </bean> <bean id="orderDao" class="com.package.service.OrderDaoImpl"/> <bean class="org.springframework.orm.jpa.support.PersistenceAnnotationBeanPostProcessor"/> <bean id="entityManagerFactory" class="org.springframework.orm.jpa.LocalContainerEntityManagerFactoryBean"> <property name="persistenceUnitName" value="MyServer"/> <property name="loadTimeWeaver"> <bean class="org.springframework.instrument.classloading.InstrumentationLoadTimeWeaver"/> </property> <property name="dataSource" ref="dataSource"/> <property name="jpaVendorAdapter"> <bean class="org.springframework.orm.jpa.vendor.HibernateJpaVendorAdapter"> <property name="showSql" value="${com.group.server.vendoradapter.showsql}"/> <property name="generateDdl" value="${com.group.server.vendoradapter.generateDdl}"/> <property name="database" value="${com.group.server.vendoradapter.database}"/> </bean> </property> </bean> <bean id="transactionManager" class="org.springframework.orm.jpa.JpaTransactionManager"> <property name="entityManagerFactory" ref="entityManagerFactory"/> <property name="dataSource" ref="dataSource"/> </bean> <bean id="dataSource" class="org.springframework.jdbc.datasource.DriverManagerDataSource"> <property name="driverClassName" value="${com.group.server.datasource.driverClassName}"/> <property name="url" value="${com.group.server.datasource.url}"/> <property name="username" value="${com.group.server.datasource.username}"/> <property name="password" value="${com.group.server.datasource.password}"/> </bean> <bean id="executorService" class="java.util.concurrent.Executors" factory-method="newCachedThreadPool"/> </beans> persistence.xml <persistence xmlns="http://java.sun.com/xml/ns/persistence" version="1.0"> <persistence-unit name="MyServer" transaction-type="RESOURCE_LOCAL"/> </persistence> OrderDaoImpl package com.group.service; import com.group.model.Order; import org.springframework.stereotype.Repository; import org.springframework.transaction.annotation.Transactional; import javax.persistence.EntityManager; import javax.persistence.PersistenceContext; import javax.persistence.Query; import java.util.List; @Repository @Transactional public class OrderDaoImpl implements OrderDao { private EntityManager entityManager; @PersistenceContext public void setEntityManager(EntityManager entityManager) { this.entityManager = entityManager; } @Override public Order find(Integer id) { Order order = entityManager.find(Order.class, id); return order; } @Override public List<Order> findAll() { Query query = entityManager.createQuery("select o from Order o"); return query.getResultList(); } @Override public List<Order> findBySymbol(String symbol) { Query query = entityManager.createQuery("select o from Order o where o.symbol = :symbol"); return query.setParameter("symbol", symbol).getResultList(); } }

  Read the article

• My computer freezes irregularly

  - by Manhim

  My computer started to freeze at irregular times for 3 weeks now. Please note that this question change with each things that i try. (For additional details) What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. Sometimes my G-15 LCD screen flickers and caracters gets caried around temporary under heavy load. Now, most of the times, the BIOS hard disks boot order gets reversed for some reason and I have to put it to the right one and save each times I boot. (Might be unrelated, not sure, but it first started yesterday) Sometimes the BIOS doesn't detect my 750GB hard drive plugged in SATA1. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 45-55. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu Ran 6 short different CPU stress test on Fedora 15 (Haven't found any complete stress testers for Linux) and it didn't crash. Changed the thermal paste to some Artic Silver 5 for my CPU and stress tested the CPU, temperature was at 50 idle, then 64 highest and slowly went down to 62 during the test. Ran some stress testing with a temporary graphic card and it went ok. Ran furmark stress test with my original graphic card and it freezed again. GPU had a temp of 74C, a CPU temp of 58C and a mobo temp of 40C or 45C (Dunno which one it is from SpeedFan). Ran a furmark stress test and a CPU stress test at the same time, results: http://pastebin.com/2t6PLpdJ I have been using my computer without stressing it for about 2 hours now and no crashes yet. I also have disabled the AMD Cool'n'quiet function on the BIOS for a more regular power to the CPU. When I ran Furmark without C'n'q my computer didn't freeze but I had a "Driver Kernel Error" that have recovered (And Furmark crashed) all that while running a CPU stress test. The computer eventually frozed without me being at it, but this time my screen just went on sleep and I couldn't wake it. Using the stability tester in nTune my computer freezed again (In the same manner as before). I notived that Speedfan gives me a -12V of -16.97V and a -5V of -8.78V. I wonder if these numbers are reliable and if they are good or bad. I have swapped my G-15 with another basic USB keyboard (HP) and I have ran furmark for about 10 minutes with a CPU stability test running each 60 seconds for 30 seconds and my computer haven't crashed yet. Ran some more extended tests without my G-15 and it freezed like it usually do. Removed the nForce Hard disk controler. Disabled command queuing in the NVIDIA nForce SATA Controller for both port 0 and port 1 (Errors from the logs) Used CPUID HwMonitor, here are the voltages: http://pastebin.com/dfM7p4jV Changed some configurations in the motherboard BIOS: Disabled PEG Link Mode, Changed AI Tuning to Standard, Disabled the 1394 Controller, Disabled HD Audio, Disabled JMicron RAID controller and Disabled SATA Raid. When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) When my Graphic card and my CPU are stressed. Sometimes when my Graphic card is stressed. Never happenned while stressing only the CPU. Sometimes when my CPU is stressed. Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) Event logs (Warnings, errors and critical errors) for the last 24 hours: http://pastebin.com/Bvvk31T7 My current to-try list Reinstall the drivers and software 1 by 1 and do extensive stress testing between each. Update the BIOS firmware to the most recent stable one. Change my motherboard. Status updates Keeping only the last 3 (28/06 04pm) More stress testing and still pass the tests. (28/06 03pm) Been stress testing for 10 minute straight now and 5 minutes with both CPU and GPU being stressed at the same time. (28/06 03pm) Stress-testing right now, so far no problems. A little hope Tests with Furmark and Prime95. Testing Windows bare-bone: 30 Minutes stress, no freeze. Installing an Anti-virus and some software, restarting computer. Testing with Anti-virus and some software (No drivers installed): 30 Minutes stress, no freeze. Installing audio drivers, restarting computer. Testing with the audio drivers: 30 Minutes stress, no freeze. Installing the latest graphic drivers from EVGA's website (without 3d vision since I don't use it), restarting computer. Testing with the graphic drivers: 30 Minutes stress, no freeze. Configuring Windows to my liking and installing more softwares. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

  Read the article

• Hard Disk DRDY error: is it a crash

  - by pranjal

  I am using IBM Thinkpad, 1.7GHz, 512 RAM with Linux Mint 9 installed. I have two partitions in addition to root. One of the partitions became read-only yesterday, after which I rebooted my system. It is extremely slow along with DRDY Error : Is my Hard disk crashed ? Error Log while booting. Differences between boot sector and its backup. failed command : READ DMA BMDMA : stat 0X25 ata 1.00 : status : { DRDY ERR } ata 1.00 : status :{ UNC } Buffer I/O error on logical device, logical block 65467 smartctl output for the partition: mint mint # smartctl -a /dev/sda1 smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: TOSHIBA MK4026GAX RoHS Serial Number: X5LY1623T Firmware Version: PA107E User Capacity: 40,007,761,920 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Feb 17 06:48:25 2011 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 153) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 310 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3968 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 40 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 7257 10 Spin_Retry_Count 0x0033 179 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3484 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 489 193 Load_Cycle_Count 0x0032 064 064 000 Old_age Always - 367150 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Lifetime Min/Max 14/57) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 33 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 82 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 1 199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 101 222 Loaded_Hours 0x0032 085 085 000 Old_age Always - 6146 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 227 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 2371 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2371 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:03:10.061 READ DMA f8 00 00 00 00 00 e0 00 00:03:10.061 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:03:10.053 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:03:10.053 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:03:10.053 READ NATIVE MAX ADDRESS Error 2370 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:03:03.328 READ DMA f8 00 00 00 00 00 e0 00 00:03:03.327 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:03:03.320 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:03:03.319 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:03:03.319 READ NATIVE MAX ADDRESS Error 2369 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:56.582 READ DMA f8 00 00 00 00 00 e0 00 00:02:56.582 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:56.574 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:56.574 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:56.574 READ NATIVE MAX ADDRESS Error 2368 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:49.809 READ DMA f8 00 00 00 00 00 e0 00 00:02:49.809 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:49.801 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:49.801 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:49.801 READ NATIVE MAX ADDRESS Error 2367 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:43.056 READ DMA f8 00 00 00 00 00 e0 00 00:02:43.056 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:43.048 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:43.048 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:43.047 READ NATIVE MAX ADDRESS SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging Do I need to get a new Hard Disk my PC ?

  Read the article

• Our embedded linux system won't recognize a USB Device if it is plugged in before powerup. Suggestions?

  - by Blaine

  We are developing on a small embedded device. This device us a gumstix overo board running OpenEmbedded linux. We have our development almost completely done, and have run into the strangest of bugs that we can't figure out. We have a USB Device (Spectrophotometer) that has a USB2.0 Connection and an external power supply for the light source. Typical behavior is that you plug in the power supply, then the USB connection to a host. When the usb connection is detected by the device, the device boots up and enables the light source and fan. The device is then able to be used by the host system. The problem is that if the device is plugged into the Gumstix before we turn on the Gumstix, the USB Device apparently is not probed by the system (and hence does not turn on). Under a normal situation, when the connection is initialized by plugging in the usb cable, the spectro turns itself on and becomes available to the system (this can be seen via "lsusb" typically). Neither of these things are happening. There is no device detected via "lsusb" and no dmesg errors of any kind that we can see. It is as if the device is not plugged in. The device does show up and work fine if we unplug the USB cable and plug it back in once the system is booted up. It turns on and shows up on the usb bus, and we can access it with our driver. On any other desktop or laptop, it does not matter if the host system is on or off when we plug in the spectrometer. This behavior is what I would consider to be "normal" - that the usb system is probed and initialized at boot time, and the usb devices come online. In other words, our system is fully functional as long as we plug in the usb device after the system is booted up. Unfortunately this isn't possible in our final product - everything comes on at once. Additional Info: 1) We have tried a flash drive attached to the system when the system is turned off. Booting up the system brings the flash drive online, as expected 2) There are no messages regarding the spectro or usb device (using dmesg). "lsusb" only lists the USB hubs / controllers. It is literally as if the device is not present and not plugged in. 3) We have tried a brand new image from gumstix and an older image from last year. Both images have this problem. This problem exists on all 3 gumstix devices we use. Does anyone have any suggestions? From what I can tell it isn't really possible to do a complete "reboot" of the usb system that is a complete emulation of "unplugging" and "replugging" a usb device. I feel like what is happening is that there is no initial probe on the usb bus that would trigger the usb handshaking, but this is somehow specific to the spectro. This seems to be a kernel issue or at least an issue in how the kernel is initializing the usb subsystem. I'm not really sure though. I have tried the gumstix mailing list, but there doesn't seem to be anyone who has seen this issue before. Any advice or suggestions on where to start looking would be fantastic. Thank you! Blaine output etc. $ uname -a Linux overo 2.6.33 #1 Tue Apr 27 08:35:38 PDT 2010 armv7l GNU/Linux When the system is up and running and spectro is plugged in (working as intended), this is lsusb: Bus 001 Device 116: ID 2457:1022 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x2457 idProduct 0x1022 bcdDevice 0.02 iManufacturer 1 USB4000 1.01.11 iProduct 2 Ocean Optics USB4000 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 46 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 400mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 4 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) dmesg output: usb usb1: usb auto-resume hub 1-0:1.0: hub_resume usb usb2: usb auto-resume ehci-omap ehci-omap.0: resume root hub hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 hub 2-0:1.0: hub_resume hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend ehci-omap ehci-omap.0: suspend root hub usb usb2: usb resume ehci-omap ehci-omap.0: resume root hub hub 2-0:1.0: hub_resume ehci-omap ehci-omap.0: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT hub 2-0:1.0: port 2: status 0501 change 0001 hub 2-0:1.0: state 7 ports 3 chg 0004 evt 0000 hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: new high speed USB device using ehci-omap and address 2 ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: default language 0x0409 usb 2-2: udev 2, busnum 2, minor = 129 usb 2-2: New USB device found, idVendor=2457, idProduct=1022 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: Ocean Optics USB4000 usb 2-2: Manufacturer: USB4000 1.01.11 usb 2-2: uevent usb 2-2: usb_probe_device usb 2-2: configuration #1 chosen from 1 choice usb 2-2: uevent usb 2-2: adding 2-2:1.0 (config #1, interface 0) usb 2-2:1.0: uevent drivers/usb/core/inode.c: creating file '002' dmesg has nothing to say, and lusb simply lists nothing else but the two default usb controllers / hubs if we plug the device in before the system is turned on.

  Read the article

• Problem Showing Sensors Details

  - by Skatephone

  Hi, i'm looking to show detail about sensors in an Actvity but when i put my app in to my phone i manage to view only details about the accellerometer, but the program says that i have 4 sensors: Accellerometer, Magnetic field, Orientation and Temperature. I'm using Android 1.6 and a htc Tattoo for testing. This is my code: public class SensorInfo extends Activity { private SensorManager mSensorManager; TextView mTextAcc,mTextGyr,mTextLig,mTextMag,mTextOri, mTextPre,mTextPro,mTextTem, mSensorsTotTitle,mSensorAvailablesTitle,mTextAccTitle,mTextGyrTitle,mTextLigTitle,mTextMagTitle,mTextOriTitle, mTextPreTitle,mTextProTitle,mTextTemTitle; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.detaillayout); // Get the texts fields of the layout and setup to invisible setTextViews(); // Get the SensorManager mSensorManager= (SensorManager) getSystemService(SENSOR_SERVICE); // List of Sensors Available List<Sensor> msensorList = mSensorManager.getSensorList(Sensor.TYPE_ALL); // Print Sensor Details Sensor sens; int type,i; String text = new String(""); // Do the list of available sensors on a String and print detail about each sensor for (i=0;i<msensorList.size();i++){ sens = msensorList.get(i); type = sens.getType(); text = " - "+getString(R.string.power)+" "+String.valueOf(sens.getPower())+"mA\n"; text+= " - "+getString(R.string.resolution)+" "+String.valueOf(sens.getResolution())+"\n"; text+= " - "+getString(R.string.maxrange)+" "+String.valueOf(sens.getMaximumRange ())+"\n"; text+= " - "+getString(R.string.vendor)+" "+sens.getVendor()+"\n"; text+= " - "+getString(R.string.version)+" "+String.valueOf(sens.getVersion()); switch(type) { // Check the type of Sensor that generate the event and show is resolution case Sensor.TYPE_ACCELEROMETER: mTextAccTitle.setVisibility(0); mTextAccTitle.setMaxHeight(30); mTextAcc.setVisibility(0); mTextAcc.setMaxHeight(100); mTextAcc.setText(text); // Print data of the Sensor break; case Sensor.TYPE_GYROSCOPE: mTextGyrTitle.setVisibility(0); mTextGyr.setVisibility(0); mTextGyr.setText(text); // Print data of the Sensor break; case Sensor.TYPE_LIGHT: mTextLigTitle.setVisibility(0); mTextLig.setVisibility(0); mTextLig.setText(text); // Print data of the Sensor break; case Sensor.TYPE_MAGNETIC_FIELD: mTextMagTitle.setVisibility(0); mTextMag.setVisibility(0); mTextMag.setText(text); // Print data of the Sensor break; case Sensor.TYPE_ORIENTATION: mTextOriTitle.setVisibility(0); mTextOri.setVisibility(0); mTextOri.setText(text); // Print data of the Sensor break; case Sensor.TYPE_PRESSURE: mTextPreTitle.setVisibility(0); mTextPre.setVisibility(0); mTextPre.setText(text); // Print data of the Sensor break; case Sensor.TYPE_PROXIMITY: mTextProTitle.setVisibility(0); mTextPro.setVisibility(0); mTextPro.setText(text); // Print data of the Sensor break; case Sensor.TYPE_TEMPERATURE: mTextTemTitle.setVisibility(0); mTextTem.setVisibility(0); mTextTem.setText(text); // Print data of the Sensor break; } } } // Get the texts fields of the layout and setup to invisible void setTextViews(){ mTextAccTitle = (TextView) findViewById(R.id.sensorAccTitle); mTextAccTitle.setVisibility(4); mTextAccTitle.setMaxHeight(0); mTextAcc = (TextView) findViewById(R.id.sensorAcc); mTextAcc.setMaxHeight(0); mTextAcc.setVisibility(4); mTextGyrTitle = (TextView) findViewById(R.id.sensorGyrTitle); mTextGyrTitle.setVisibility(4); mTextGyrTitle.setMaxHeight(0); mTextGyr = (TextView) findViewById(R.id.sensorGyr); mTextGyr.setVisibility(4); mTextGyrTitle.setMaxHeight(0); mTextLigTitle = (TextView) findViewById(R.id.sensorLigTitle); mTextLigTitle.setVisibility(4); mTextLigTitle.setMaxHeight(0); mTextLig = (TextView) findViewById(R.id.sensorLig); mTextLig.setVisibility(4); mTextLig.setMaxHeight(0); mTextMagTitle = (TextView) findViewById(R.id.sensorMagTitle); mTextMagTitle.setVisibility(4); mTextMagTitle.setMaxHeight(0); mTextMag = (TextView) findViewById(R.id.sensorMag); mTextMag.setVisibility(4); mTextMag.setMaxHeight(0); mTextOriTitle = (TextView) findViewById(R.id.sensorOriTitle); mTextOriTitle.setVisibility(4); mTextOriTitle.setMaxHeight(0); mTextOri = (TextView) findViewById(R.id.sensorOri); mTextOri.setVisibility(4); mTextOri.setMaxHeight(0); mTextPreTitle = (TextView) findViewById(R.id.sensorPreTitle); mTextPreTitle.setVisibility(4); mTextPreTitle.setMaxHeight(0); mTextPre = (TextView) findViewById(R.id.sensorPre); mTextPre.setVisibility(4); mTextPre.setMaxHeight(0); mTextProTitle = (TextView) findViewById(R.id.sensorProTitle); mTextProTitle.setVisibility(4); mTextProTitle.setMaxHeight(0); mTextPro = (TextView) findViewById(R.id.sensorPro); mTextPro.setVisibility(4); mTextPro.setMaxHeight(0); mTextTemTitle = (TextView) findViewById(R.id.sensorTemTitle); mTextTemTitle.setVisibility(4); mTextTemTitle.setMaxHeight(0); mTextTem = (TextView) findViewById(R.id.sensorTem); mTextTem.setVisibility(4); mTextTem.setMaxHeight(0); } } Tank's Valerio From Italy

  Read the article

• What to filter when providing very limited open WiFi to a small conference or meeting?

  - by Tim Farley

  Executive Summary The basic question is: if you have a very limited bandwidth WiFi to provide Internet for a small meeting of only a day or two, how do you set the filters on the router to avoid one or two users monopolizing all the available bandwidth? For folks who don't have the time to read the details below, I am NOT looking for any of these answers: Secure the router and only let a few trusted people use it Tell everyone to turn off unused services & generally police themselves Monitor the traffic with a sniffer and add filters as needed I am aware of all of that. None are appropriate for reasons that will become clear. ALSO NOTE: There is already a question concerning providing adequate WiFi at large (500 attendees) conferences here. This question concerns SMALL meetings of less than 200 people, typically with less than half that using the WiFi. Something that can be handled with a single home or small office router. Background I've used a 3G/4G router device to provide WiFi to small meetings in the past with some success. By small I mean single-room conferences or meetings on the order of a barcamp or Skepticamp or user group meeting. These meetings sometimes have technical attendees there, but not exclusively. Usually less than half to a third of the attendees will actually use the WiFi. Maximum meeting size I'm talking about is 100 to 200 people. I typically use a Cradlepoint MBR-1000 but many other devices exist, especially all-in-one units supplied by 3G and/or 4G vendors like Verizon, Sprint and Clear. These devices take a 3G or 4G internet connection and fan it out to multiple users using WiFi. One key aspect of providing net access this way is the limited bandwidth available over 3G/4G. Even with something like the Cradlepoint which can load-balance multiple radios, you are only going to achieve a few megabits of download speed and maybe a megabit or so of upload speed. That's a best case scenario. Often it is considerably slower. The goal in most of these meeting situations is to allow folks access to services like email, web, social media, chat services and so on. This is so they can live-blog or live-tweet the proceedings, or simply chat online or otherwise stay in touch (with both attendees and non-attendees) while the meeting proceeds. I would like to limit the services provided by the router to just those services that meet those needs. Problems In particular I have noticed a couple of scenarios where particular users end up abusing most of the bandwidth on the router, to the detriment of everyone. These boil into two areas: Intentional use. Folks looking at YouTube videos, downloading podcasts to their iPod, and otherwise using the bandwidth for things that really aren't appropriate in a meeting room where you should be paying attention to the speaker and/or interacting.At one meeting that we were live-streaming (over a separate, dedicated connection) via UStream, I noticed several folks in the room that had the UStream page up so they could interact with the meeting chat - apparently oblivious that they were wasting bandwidth streaming back video of something that was taking place right in front of them. Unintentional use. There are a variety of software utilities that will make extensive use of bandwidth in the background, that folks often have installed on their laptops and smartphones, perhaps without realizing.Examples: Peer to peer downloading programs such as Bittorrent that run in the background Automatic software update services. These are legion, as every major software vendor has their own, so one can easily have Microsoft, Apple, Mozilla, Adobe, Google and others all trying to download updates in the background. Security software that downloads new signatures such as anti-virus, anti-malware, etc. Backup software and other software that "syncs" in the background to cloud services. For some numbers on how much network bandwidth gets sucked up by these non-web, non-email type services, check out this recent Wired article. Apparently web, email and chat all together are less than one quarter of the Internet traffic now. If the numbers in that article are correct, by filtering out all the other stuff I should be able to increase the usefulness of the WiFi four-fold. Now, in some situations I've been able to control access using security on the router to limit it to a very small group of people (typically the organizers of the meeting). But that's not always appropriate. At an upcoming meeting I would like to run the WiFi without security and let anyone use it, because it happens at the meeting location the 4G coverage in my town is particularly excellent. In a recent test I got 10 Megabits down at the meeting site. The "tell people to police themselves" solution mentioned at top is not appropriate because of (a) a largely non-technical audience and (b) the unintentional nature of much of the usage as described above. The "run a sniffer and filter as needed" solution is not useful because these meetings typically only last a couple of days, often only one day, and have a very small volunteer staff. I don't have a person to dedicate to network monitoring, and by the time we got the rules tweaked completely the meeting will be over. What I've Got First thing, I figured I would use OpenDNS's domain filtering rules to filter out whole classes of sites. A number of video and peer-to-peer sites can be wiped out using this. (Yes, I am aware that filtering via DNS technically leaves the services accessible - remember, these are largely non-technical users attending a 2 day meeting. It's enough). I figured I would start with these selections in OpenDNS's UI: I figure I will probably also block DNS (port 53) to anything other than the router itself, so that folks can't bypass my DNS configuration. A savvy user could get around this, because I'm not going to put a lot of elaborate filters on the firewall, but I don't care too much. Because these meetings don't last very long, its probably not going to be worth the trouble. This should cover the bulk of the non-web traffic, i.e. peer-to-peer and video if that Wired article is correct. Please advise if you think there are severe limitations to the OpenDNS approach. What I Need Note that OpenDNS focuses on things that are "objectionable" in some context or another. Video, music, radio and peer-to-peer all get covered. I still need to cover a number of perfectly reasonable things that we just want to block because they aren't needed in a meeting. Most of these are utilities that upload or download legit things in the background. Specifically, I'd like to know port numbers or DNS names to filter in order to effectively disable the following services: Microsoft automatic updates Apple automatic updates Adobe automatic updates Google automatic updates Other major software update services Major virus/malware/security signature updates Major background backup services Other services that run in the background and can eat lots of bandwidth I also would like any other suggestions you might have that would be applicable. Sorry to be so verbose, but I find it helps to be very, very clear on questions of this nature, and I already have half a solution with the OpenDNS thing.

  Read the article

• Why are my hard drives failing?

  - by WishCow

  I have a small Ubuntu server running at home, with 2 HDDs. There are two software raids (raid1) on the disks, managed by mdadm, which I believe is irrelevant, but mentioning it anyway. Both of the HDDs are Western Digital, and have been used for around 2 years, when one of them started making clicking noises, and died. I figured that maybe it's natural after 2 years, so I bought a new one, and resynced the raid arrays. After about a month, the other drive also died. I didn't get suspicious, since both drives have been bought at the same time, it's not that surprising to see both of them near each other, so I bought another one. So far, 2 old drives failed, and 2 brand new in the system. After one month, one of the new drives died. This is when it started getting suspicious. Since the PC was put together from some really old parts (think AthlonXP), I figured that maybe the motherboard's SATA controller is the culprit. Of course you can't switch parts easily in an old PC like this, so I bought a whole system, new MB, new CPU, new RAM. Took the just failed drive back, since it was under warranty, and got it replaced. So it is up to 2 failed drives from the old ones, and 1 failed drive from the new ones. No problems, for 1 month. After that errors were creeping up again in /var/log/messages, and mdadm was reporting raid array failures. I started tearing my hair out. Everything is new in the system, it's up to the third brand new HDD, it's simply not possible that all of the new drives that I bought were faulty. Let's see what is still common... the cables. Okay, long shot, let's replace the SATA cables. Take HDD back, smile to the guy at the counter and say that I'm really unlucky. He replaces the HDD. I come home, one month passes and one of HDDs fails, again. I'm not joking. Two of the brand new HDDs have failed. Maybe it's a bug in the OS. Let's see what the manufacturer's testing tool says. Download testing tool, burn it to a CD, reboot, leave HDD testing overnight. Test says that the drive is faulty, and I should back up everything, if I still can. I don't know what's happening, but it does not look like a software problem, something is definitely thrashing the HDDs. I should mention now, that the whole system is in a shoebox. Since there are a load of "build your own ikea case" stuff, I thought there shouldn't be any problems throwing the thing in a box, and stuffing it away somewhere. The box is well ventilated, but I thought that just maybe the drives were overheating. There is no other possible answer to this. So I took the HDD back, and got it replaced (for the 3rd time), and bought HDD coolers. And just now, I have heard the sound of doom. click click whizzzzzzzzz. SSH into the box: You have new mail! mail r 1 DegradedArrayEvent on /dev/md0 ... dmesg output: [47128.000051] ata3: lost interrupt (Status 0x50) [47128.000097] end_request: I/O error, dev sda, sector 58588863 [47128.000134] md: super_written gets error=-5, uptodate=0 [48043.976054] ata3: lost interrupt (Status 0x50) [48043.976086] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [48043.976132] ata3.00: cmd c8/00:18:bf:40:52/00:00:00:00:00/e1 tag 0 dma 12288 in [48043.976135] res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) [48043.976208] ata3.00: status: { DRDY } [48043.976241] ata3: soft resetting link [48044.148446] ata3.00: configured for UDMA/133 [48044.148457] ata3.00: device reported invalid CHS sector 0 [48044.148477] ata3: EH complete Recap: No possibility of overheating 6 drives have failed, 4 of those have been brand new. I'm not sure now that the original two have been faulty, or suffered the same thing that the new ones. There is nothing common in the system, apart from the OS which is Ubuntu Karmic now (started with Jaunty). New MB, new CPU, new RAM, new SATA cables. No, the little holes on the HDD are not covered I'm crying. Really. I don't have the face to return to the store now, it's not possible for 4 drives to fail under 4 months. A few ideas that I have been thinking: Is it possible that I fuck up something when I partition and resync the drives? Can it be so bad that it physicaly wrecks the drive? (since the vendor supplied tool says that the drive is damaged) I do the partitoning with fdisk, and use the same block size for the raid1 partitions (I check the exact block sizes with fdisk -lu) Is it possible that the linux kernel or mdadm, or something is not compatible with this exact brand of HDDs, and thrashes them? Is it possible that it may be the shoebox? Try placing it somewhere else? It's under a shelf now, so humidity is not a problem either. Is it possible that a normal PC case will solve my problem (I'm going to shoot myself then)? I will get a picture tomorrow. Am I just simply cursed? Any help or speculation is greatly appreciated. Edit: The power strip is guarded against overvoltage. Edit2: I have moved inbetween these 4 months, so the possibility of the cause being "dirty" electricity in both places, is very low. Edit3: I have checked the voltages in the BIOS (couldn't borrow a multimeter), and they are all seem correct, the biggest discrepancy is in the 12V, because it's supplying 11.3. Should I be worried about that? Edit4: I put my desktop PC's PSU into the server. The BIOS reported much more accurate voltage readings, and also it has successfully rebuilt the raid1 array, which took some 3-4 hours, so I feel a little positive now. Will get a new PSU tomorrow to test with that. Also, attaching the picture about the box: (disregard the 3rd drive)

  Read the article

• What do I need to change to get this 'acts_as_rateable' Rails plugin working with this code from the

  - by tepidsam

  Hello! I'm working my way through the 'Foundation Rails 2' book. In Chapter 9, we are building a little "plugins" app. In the book, he installs the acts_as_rateable plugin found at http://juixe.com/svn/acts_as_rateable. This plugin doesn't appear to exist in 2010 (the page for this "old" plugin seems to be working again...it was down when I tried it earlier), so I found another acts_as_rateable plugin at http://github.com/azabaj/acts_as_rateable. These plugins are different and I'm trying to get the "new" plugin working with the code/project/app from the Foudations 2 book. I was able to use the migration generator included with the "new" plugin and it worked. Now,though, I'm a bit confused. In the book, he has us create a new controller to work with the plugin (the old plugin). Here's the code for that: class RatingsController < ApplicationController def create @plugin = Plugin.find(params[:plugin_id]) rating = Rating.new(:rating => params[:rating]) @plugin.ratings << average_rating redirect_to @plugin end end Then he had us change the routing: map.resources :plugins, :has_many => :ratings map.resources :categories map.root :controller => 'plugins' Next, we modified the following to the 'show' template so that it looks like this: <div id="rate_plugin"> <h2>Rate this plugin</h2> <ul class="star-rating"> <li> <%= link_to "1", @plugin.rate_it(1), :method => :post, :title => "1 star out of 5", :class => "one-star" %> </li> <li> <%= link_to "2", plugin_ratings_path(@plugin, :rating => 2), :method => :post, :title => "2 stars out of 5", :class => "two-stars" %> </li> <li> <%= link_to "3", plugin_ratings_path(@plugin, :rating => 3), :method => :post, :title => "3 stars out of 5", :class => "three-stars" %> </li> <li> <%= link_to "4", plugin_ratings_path(@plugin, :rating => 4), :method => :post, :title => "4 stars out of 5", :class => "four-stars" %> </li> <li> <%= link_to "5", plugin_ratings_path(@plugin, :rating => 5), :method => :post, :title => "5 stars out of 5", :class => "five-stars" %> </li> </ul> </div> The problem is that we're using code for a different plugin. When I try to actually "rate" one of the plugins, I get an "unknown attribute" error. That makes sense. I'm using attribute names for the "old" plugin, but I should be using attributes names for the "new" plugin. The problem is...I've tried using a variety of different attribute names and I keep getting the same error. From the README for the "new" plugin, I think I should be using some of these but I haven't been able to get them working: Install the plugin into your vendor/plugins directory, insert 'acts_as_rateable' into your model, then restart your application. class Post < ActiveRecord::Base acts_as_rateable end Now your model is extended by the plugin, you can rate it ( 1-# )or calculate the average rating. @plugin.rate_it( 4, current_user.id ) @plugin.average_rating #=> 4.0 @plugin.average_rating_round #=> 4 @plugin.average_rating_percent #=> 80 @plugin.rated_by?( current_user ) #=> rating || false Plugin.find_average_of( 4 ) #=> array of posts See acts_as_rateable.rb for further details! I'm guessing that I might have to make some "bigger" changes to get this plugin working. I'm asking this question to learn and only learn. The book gives code to get things working with the old plugin, but if one were actually building this app today it would be necessary to use this "new" plugin, so I would like to see how it could be used. Cheers! Any ideas on what I could change to get the "new" plugin working?

  Read the article

• Perl - Reading .txt files line-by-line and using compare function (printing non-matches only once)

  - by Kurt W

  I am really struggling and have spent about two full days on this banging my head against receiving the same result every time I run this perl script. I have a Perl script that connects to a vendor tool and stores data for ~26 different elements within @data. There is a foreach loop for @data that breaks the 26 elements into $e-{'element1'), $e-{'element2'), $e-{'element3'), $e-{'element4'), etc. etc. etc. I am also reading from the .txt files within a directory (line-by-line) and comparing the server names that exist within the text files with what exists in $e-{'element4'}. The Problem: Matches are working perfectly and only printing one line for each of the 26 elements when there is a match, however non-matches are producing one line for every entry within the .txt files (37 in all). So if there are 100 entries (each entry having 26 elements) stored within @data, then there are 100 x 37 entries being printed. So for every non-match in the: if ($e-{'element4'} eq '6' && $_ =~ /$e-{element7}/i) statement below, I am receiving a print out saying that there is not a match. 37 entries for the same identical 26 elements (because there are 37 total entries in all of the .txt files). The Goal: I need to print out only 1 line for each unique entry (a unique entry being $e-{element1} thru $e-{element26}). It is already printing one 1 line for matches, but it is printing out 37 entries when there is not a match. I need to treat matches and non-matches differently. Code: foreach my $e (@data) { # Open the .txt files stored within $basePath and use for comparison: opendir(DIRC, $basePath . "/") || die ("cannot open directory"); my @files=(readdir(DIRC)); my @MPG_assets = grep(/(.*?).txt/, @files); # Loop through each system name found and compare it with the data in SC for a match: foreach(@MPG_assets) { $filename = $_; open (MPGFILES, $basePath . "/" . $filename) || die "canot open the file"; while(<MPGFILES>) { if ($e->{'element4'} eq '6' && $_ =~ /$e->{'element7'}/i) { ## THIS SECTION WORKS PERFECTLY AND ONLY PRINTS MATCHES WHERE $_ ## (which contains the servernames (1 per line) in the .txt files) ## EQUALS $e->{'element7'}. print $e->{'element1'} . "\n"; print $e->{'element2'} . "\n"; print $e->{'element3'} . "\n"; print $e->{'element4'} . "\n"; print $e->{'element5'} . "\n"; # ... print $e->{'element26'} . "\n"; } else { ## **THIS SECTION DOES NOT WORK**. FOR EVERY NON-MATCH, THERE IS A ## LINE PRINTED WITH 26 IDENTICAL ELEMENTS BECAUSE ITS LOOPING THRU ## THE 37 LINES IN THE *.TXT FILES. print $e->{'element1'} . "\n"; print $e->{'element2'} . "\n"; print $e->{'element3'} . "\n"; print $e->{'element4'} . "\n"; print $e->{'element5'} . "\n"; # ... print $e->{'element26'} . "\n"; } # End of 'if ($e->{'element4'} eq..' statement } # End of while loop } # End of 'foreach(@MPG_assets)' } # End of 'foreach my $e (@data)' I think I need something to identical unique elements and define what fields make up a unique element but honestly I have tried everything I know. If you would be so kind to provide actual code fixes, that would be wonderful because I am headed to production with this script quite soon. Also. I am looking for code (ideally) that is very human-readable because I will need to document it so others can understand. Please let me know if you need additional information.

  Read the article

• .NET HTML Sanitation for rich HTML Input

  - by Rick Strahl

  Recently I was working on updating a legacy application to MVC 4 that included free form text input. When I set up the new site my initial approach was to not allow any rich HTML input, only simple text formatting that would respect a few simple HTML commands for bold, lists etc. and automatically handles line break processing for new lines and paragraphs. This is typical for what I do with most multi-line text input in my apps and it works very well with very little development effort involved. Then the client sprung another note: Oh by the way we have a bunch of customers (real estate agents) who need to post complete HTML documents. Oh uh! There goes the simple theory. After some discussion and pleading on my part (<snicker>) to try and avoid this type of raw HTML input because of potential XSS issues, the client decided to go ahead and allow raw HTML input anyway. There has been lots of discussions on this subject on StackOverFlow (and here and here) but to after reading through some of the solutions I didn't really find anything that would work even closely for what I needed. Specifically we need to be able to allow just about any HTML markup, with the exception of script code. Remote CSS and Images need to be loaded, links need to work and so. While the 'legit' HTML posted by these agents is basic in nature it does span most of the full gamut of HTML (4). Most of the solutions XSS prevention/sanitizer solutions I found were way to aggressive and rendered the posted output unusable mostly because they tend to strip any externally loaded content. In short I needed a custom solution. I thought the best solution to this would be to use an HTML parser - in this case the Html Agility Pack - and then to run through all the HTML markup provided and remove any of the blacklisted tags and a number of attributes that are prone to JavaScript injection. There's much discussion on whether to use blacklists vs. whitelists in the discussions mentioned above, but I found that whitelists can make sense in simple scenarios where you might allow manual HTML input, but when you need to allow a larger array of HTML functionality a blacklist is probably easier to manage as the vast majority of elements and attributes could be allowed. Also white listing gets a bit more complex with HTML5 and the new proliferation of new HTML tags and most new tags generally don't affect XSS issues directly. Pure whitelisting based on elements and attributes also doesn't capture many edge cases (see some of the XSS cheat sheets listed below) so even with a white list, custom logic is still required to handle many of those edge cases. The Microsoft Web Protection Library (AntiXSS) My first thought was to check out the Microsoft AntiXSS library. Microsoft has an HTML Encoding and Sanitation library in the Microsoft Web Protection Library (formerly AntiXSS Library) on CodePlex, which provides stricter functions for whitelist encoding and sanitation. Initially I thought the Sanitation class and its static members would do the trick for me,but I found that this library is way too restrictive for my needs. Specifically the Sanitation class strips out images and links which rendered the full HTML from our real estate clients completely useless. I didn't spend much time with it, but apparently I'm not alone if feeling this library is not really useful without some way to configure operation. To give you an example of what didn't work for me with the library here's a small and simple HTML fragment that includes script, img and anchor tags. I would expect the script to be stripped and everything else to be left intact. Here's the original HTML:var value = "<b>Here</b> <script>alert('hello')</script> we go. Visit the " + "<a href='http://west-wind.com'>West Wind</a> site. " + "<img src='http://west-wind.com/images/new.gif' /> " ; and the code to sanitize it with the AntiXSS Sanitize class:@Html.Raw(Microsoft.Security.Application.Sanitizer.GetSafeHtmlFragment(value)) This produced a not so useful sanitized string: Here we go. Visit the <a>West Wind</a> site. While it removed the <script> tag (good) it also removed the href from the link and the image tag altogether (bad). In some situations this might be useful, but for most tasks I doubt this is the desired behavior. While links can contain javascript: references and images can 'broadcast' information to a server, without configuration to tell the library what to restrict this becomes useless to me. I couldn't find any way to customize the white list, nor is there code available in this 'open source' library on CodePlex. Using Html Agility Pack for HTML Parsing The WPL library wasn't going to cut it. After doing a bit of research I decided the best approach for a custom solution would be to use an HTML parser and inspect the HTML fragment/document I'm trying to import. I've used the HTML Agility Pack before for a number of apps where I needed an HTML parser without requiring an instance of a full browser like the Internet Explorer Application object which is inadequate in Web apps. In case you haven't checked out the Html Agility Pack before, it's a powerful HTML parser library that you can use from your .NET code. It provides a simple, parsable HTML DOM model to full HTML documents or HTML fragments that let you walk through each of the elements in your document. If you've used the HTML or XML DOM in a browser before you'll feel right at home with the Agility Pack. Blacklist based HTML Parsing to strip XSS Code For my purposes of HTML sanitation, the process involved is to walk the HTML document one element at a time and then check each element and attribute against a blacklist. There's quite a bit of argument of what's better: A whitelist of allowed items or a blacklist of denied items. While whitelists tend to be more secure, they also require a lot more configuration. In the case of HTML5 a whitelist could be very extensive. For what I need, I only want to ensure that no JavaScript is executed, so a blacklist includes the obvious <script> tag plus any tag that allows loading of external content including <iframe>, <object>, <embed> and <link> etc. <form>  is also excluded to avoid posting content to a different location. I also disallow <head> and <meta> tags in particular for my case, since I'm only allowing posting of HTML fragments. There is also some internal logic to exclude some attributes or attributes that include references to JavaScript or CSS expressions. The default tag blacklist reflects my use case, but is customizable and can be added to. Here's my HtmlSanitizer implementation:using System.Collections.Generic; using System.IO; using System.Xml; using HtmlAgilityPack; namespace Westwind.Web.Utilities { public class HtmlSanitizer { public HashSet<string> BlackList = new HashSet<string>() { { "script" }, { "iframe" }, { "form" }, { "object" }, { "embed" }, { "link" }, { "head" }, { "meta" } }; /// <summary> /// Cleans up an HTML string and removes HTML tags in blacklist /// </summary> /// <param name="html"></param> /// <returns></returns> public static string SanitizeHtml(string html, params string[] blackList) { var sanitizer = new HtmlSanitizer(); if (blackList != null && blackList.Length > 0) { sanitizer.BlackList.Clear(); foreach (string item in blackList) sanitizer.BlackList.Add(item); } return sanitizer.Sanitize(html); } /// <summary> /// Cleans up an HTML string by removing elements /// on the blacklist and all elements that start /// with onXXX . /// </summary> /// <param name="html"></param> /// <returns></returns> public string Sanitize(string html) { var doc = new HtmlDocument(); doc.LoadHtml(html); SanitizeHtmlNode(doc.DocumentNode); //return doc.DocumentNode.WriteTo(); string output = null; // Use an XmlTextWriter to create self-closing tags using (StringWriter sw = new StringWriter()) { XmlWriter writer = new XmlTextWriter(sw); doc.DocumentNode.WriteTo(writer); output = sw.ToString(); // strip off XML doc header if (!string.IsNullOrEmpty(output)) { int at = output.IndexOf("?>"); output = output.Substring(at + 2); } writer.Close(); } doc = null; return output; } private void SanitizeHtmlNode(HtmlNode node) { if (node.NodeType == HtmlNodeType.Element) { // check for blacklist items and remove if (BlackList.Contains(node.Name)) { node.Remove(); return; } // remove CSS Expressions and embedded script links if (node.Name == "style") { if (string.IsNullOrEmpty(node.InnerText)) { if (node.InnerHtml.Contains("expression") || node.InnerHtml.Contains("javascript:")) node.ParentNode.RemoveChild(node); } } // remove script attributes if (node.HasAttributes) { for (int i = node.Attributes.Count - 1; i >= 0; i--) { HtmlAttribute currentAttribute = node.Attributes[i]; var attr = currentAttribute.Name.ToLower(); var val = currentAttribute.Value.ToLower(); span style="background: white; color: green">// remove event handlers if (attr.StartsWith("on")) node.Attributes.Remove(currentAttribute); // remove script links else if ( //(attr == "href" || attr== "src" || attr == "dynsrc" || attr == "lowsrc") && val != null && val.Contains("javascript:")) node.Attributes.Remove(currentAttribute); // Remove CSS Expressions else if (attr == "style" && val != null && val.Contains("expression") || val.Contains("javascript:") || val.Contains("vbscript:")) node.Attributes.Remove(currentAttribute); } } } // Look through child nodes recursively if (node.HasChildNodes) { for (int i = node.ChildNodes.Count - 1; i >= 0; i--) { SanitizeHtmlNode(node.ChildNodes[i]); } } } } } Please note: Use this as a starting point only for your own parsing and review the code for your specific use case! If your needs are less lenient than mine were you can you can make this much stricter by not allowing src and href attributes or CSS links if your HTML doesn't allow it. You can also check links for external URLs and disallow those - lots of options.  The code is simple enough to make it easy to extend to fit your use cases more specifically. It's also quite easy to make this code work using a WhiteList approach if you want to go that route. The code above is semi-generic for allowing full featured HTML fragments that only disallow script related content. The Sanitize method walks through each node of the document and then recursively drills into all of its children until the entire document has been traversed. Note that the code here uses an XmlTextWriter to write output - this is done to preserve XHTML style self-closing tags which are otherwise left as non-self-closing tags. The sanitizer code scans for blacklist elements and removes those elements not allowed. Note that the blacklist is configurable either in the instance class as a property or in the static method via the string parameter list. Additionally the code goes through each element's attributes and looks for a host of rules gleaned from some of the XSS cheat sheets listed at the end of the post. Clearly there are a lot more XSS vulnerabilities, but a lot of them apply to ancient browsers (IE6 and versions of Netscape) - many of these glaring holes (like CSS expressions - WTF IE?) have been removed in modern browsers. What a Pain To be honest this is NOT a piece of code that I wanted to write. I think building anything related to XSS is better left to people who have far more knowledge of the topic than I do. Unfortunately, I was unable to find a tool that worked even closely for me, or even provided a working base. For the project I was working on I had no choice and I'm sharing the code here merely as a base line to start with and potentially expand on for specific needs. It's sad that Microsoft Web Protection Library is currently such a train wreck - this is really something that should come from Microsoft as the systems vendor or possibly a third party that provides security tools. Luckily for my application we are dealing with a authenticated and validated users so the user base is fairly well known, and relatively small - this is not a wide open Internet application that's directly public facing. As I mentioned earlier in the post, if I had my way I would simply not allow this type of raw HTML input in the first place, and instead rely on a more controlled HTML input mechanism like MarkDown or even a good HTML Edit control that can provide some limits on what types of input are allowed. Alas in this case I was overridden and we had to go forward and allow *any* raw HTML posted. Sometimes I really feel sad that it's come this far - how many good applications and tools have been thwarted by fear of XSS (or worse) attacks? So many things that could be done *if* we had a more secure browser experience and didn't have to deal with every little script twerp trying to hack into Web pages and obscure browser bugs. So much time wasted building secure apps, so much time wasted by others trying to hack apps… We're a funny species - no other species manages to waste as much time, effort and resources as we humans do :-) Resources Code on GitHub Html Agility Pack XSS Cheat Sheet XSS Prevention Cheat Sheet Microsoft Web Protection Library (AntiXss) StackOverflow Links: http://stackoverflow.com/questions/341872/html-sanitizer-for-net http://blog.stackoverflow.com/2008/06/safe-html-and-xss/ http://code.google.com/p/subsonicforums/source/browse/trunk/SubSonic.Forums.Data/HtmlScrubber.cs?r=61© Rick Strahl, West Wind Technologies, 2005-2012Posted in Security  HTML  ASP.NET  JavaScript   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• How to avoid the Portlet Skin mismatch

  - by Martin Deh

  here are probably many on going debates whether to use portlets or taskflows in a WebCenter custom portal application.  Usually the main battle on which side to take in these debates are centered around which technology enables better performance.  The good news is that both of my colleagues, Maiko Rocha and George Maggessy have posted their respective views on this topic so I will not have to further the discussion.  However, if you do plan to use portlets in a WebCenter custom portal application, this post will help you not have the "portlet skin mismatch" issue.   An example of the presence of the mismatch can be view from the applications log: The skin customsharedskin.desktop specified on the requestMap will be used even though the consumer's skin's styleSheetDocumentId on the requestMap does not match the local skin's styleSheetDocument's id. This will impact performance since the consumer and producer stylesheets cannot be shared. The producer styleclasses will not be compressed to avoid conflicts. A reason the ids do not match may be the jars are not identical on the producer and the consumer. For example, one might have trinidad-skins.xml's skin-additions in a jar file on the class path that the other does not have. Notice that due to the mismatch the portlet's CSS will not be able to be compressed, which will most like impact performance in the portlet's consuming portal. The first part of the blog will define the portlet mismatch and cover some debugging tips that can help you solve the portlet mismatch issue.  Following that I will give a complete example of the creating, using and sharing a shared skin in both a portlet producer and the consumer application. Portlet Mismatch Defined  In general, when you consume/render an ADF page (or task flow) using the ADF Portlet bridge, the portlet (producer) would try to use the skin of the consumer page - this is called skin-sharing. When the producer cannot match the consumer skin, the portlet would generate its own stylesheet and reference it from its markup - this is called mismatched-skin. This can happen because: The consumer and producer use different versions of ADF Faces, or The consumer has additional skin-additions that the producer doesn't have or vice-versa, or The producer does not have the consumer skin For case (1) & (2) above, the producer still uses the consumer skin ID to render its markup. For case (3), the producer would default to using portlet skin. If there is a skin mis-match then there may be a performance hit because: The browser needs to fetch this extra stylesheet (though it should be cached unless expires caching is turned off) The generated portlet markup uses uncompressed styles resulting in a larger markup It is often not obvious when a skin mismatch occurs, unless you look for either of these indicators: The log messages in the producer log, for example: The skin blafplus-rich.desktop specified on the requestMap will not be used because the styleSheetDocument id on the requestMap does not match the local skin's styleSheetDocument's id. It could mean the jars are not identical. For example, one might have trinidad-skins.xml's skin-additions in a jar file on the class path that the other does not have. View the portlet markup inside the iframe, there should be a <link> tag to the portlet stylesheet resource like this (note the CSS is proxied through consumer's resourceproxy): <link rel=\"stylesheet\" charset=\"UTF-8\" type=\"text/css\" href=\"http:.../resourceproxy/portletId...252525252Fadf%252525252Fstyles%252525252Fcache%252525252Fblafplus-rich-portlet-d1062g-en-ltr-gecko.css... Using HTTP monitoring tool (eg, firebug, httpwatch), you can see a request is made to the portlet stylesheet resource (see URL above) There are a number of reasons for mismatched-skin. For skin to match the producer and consumer must match the following configurations: The ADF Faces version (different versions may have different style selectors) Style Compression, this is defined in the web.xml (default value is false, i.e. compression is ON) Tonal styles or themes, also defined in the web.xml via context-params The same skin additions (jars with skin) are available for both producer and consumer.  Skin additions are defined in the trinidad-skins.xml, using the <skin-addition> tags. These are then aggregated from all the jar files in the classpath. If there's any jar that exists on the producer but not the consumer, or vice veras, you get a mismatch. Debugging Tips  Ensure the style compression and tonal styles/themes match on the consumer and producer, by looking at the web.xml documents for the consumer & producer applications It is bit more involved to determine if the jars match.  However, you can enable the Trinidad logging to show which skin-addition it is processing.  To enable this feature, update the logging.xml log level of both the producer and consumer WLS to FINEST.  For example, in the case of the WebLogic server used by JDeveloper: $JDEV_USER_DIR/system<version number>/DefaultDomain/config/fmwconfig/servers/DefaultServer/logging.xml Add a new entry: <logger name="org.apache.myfaces.trinidadinternal.skin.SkinUtils" level="FINEST"/> Restart WebLogic.  Run the consumer page, you should see the following logging in both the consumer and producer log files. Any entries that don't match is the cause of the mismatch.  The following is an example of what the log will produce with this setting: [SRC_CLASS: org.apache.myfaces.trinidadinternal.skin.SkinUtils] [APP: WebCenter] [SRC_METHOD: _getMetaInfSkinsNodeList] Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/announcement-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/calendar-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/custComps-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/forum-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/page-service-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/peopleconnections-kudos-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/peopleconnections-wall-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/portlet-client-adf-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/rtc-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/serviceframework-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/smarttag-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.skin/in1ar8/APP-INF/lib/spaces-service-skins.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/oracle.webcenter.composer/3yo7j/WEB-INF/lib/custComps-skin.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/adf.oracle.domain.webapp/q433f9/WEB-INF/lib/adf-richclient-impl-11.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/adf.oracle.domain.webapp/q433f9/WEB-INF/lib/dvt-faces.jar!/META-INF/trinidad-skins.xml Processing skin URL:zip:/tmp/_WL_user/adf.oracle.domain.webapp/q433f9/WEB-INF/lib/dvt-trinidad.jar!/META-INF/trinidad-skins.xml   The Complete Example The first step is to create the shared library.  The WebCenter documentation covering this is located here in section 15.7.  In addition, our ADF guru Frank Nimphius also covers this in hes blog.  Here are my steps (in JDeveloper) to create the skin that will be used as the shared library for both the portlet producer and consumer. Create a new Generic Application Give application name (i.e. MySharedSkin) Give a project name (i.e. MySkinProject) Leave Project Technologies blank (none selected), and click Finish Create the trinidad-skins.xml Right-click on the MySkinProject node in the Application Navigator and select "New" In the New Galley, click on "General", select "File" from the Items, and click OK In the Create File dialog, name the file trinidad-skins.xml, and (IMPORTANT) give the directory path to MySkinProject\src\META-INF In the trinidad-skins.xml, complete the skin entry.  for example: <?xml version="1.0" encoding="windows-1252" ?> <skins xmlns="http://myfaces.apache.org/trinidad/skin">   <skin>     <id>mysharedskin.desktop</id>     <family>mysharedskin</family>     <extends>fusionFx-v1.desktop</extends>     <style-sheet-name>css/mysharedskin.css</style-sheet-name>   </skin> </skins> Create CSS file In the Application Navigator, right click on the META-INF folder (where the trinidad-skins.xml is located), and select "New" In the New Gallery, select Web-Tier-> HTML, CSS File from the the Items and click OK In the Create Cascading Style Sheet dialog, give the name (i.e. mysharedskin.css) Ensure that the Directory path is the under the META-INF (i.e. MySkinProject\src\META-INF\css) Once the new CSS opens in the editor, add in a style selector.  For example, this selector will style the background of a particular panelGroupLayout: af|panelGroupLayout.customPGL{     background-color:Fuchsia; } Create the MANIFEST.MF (used for deployment JAR) In the Application Navigator, right click on the META-INF folder (where the trinidad-skins.xml is located), and select "New" In the New Galley, click on "General", select "File" from the Items, and click OK In the Create File dialog, name the file MANIFEST.MF, and (IMPORTANT) ensure that the directory path is to MySkinProject\src\META-INF Complete the MANIFEST.MF, where the extension name is the shared library name Manifest-Version: 1.1 Created-By: Martin Deh Implementation-Title: mysharedskin Extension-Name: mysharedskin.lib.def Specification-Version: 1.0.1 Implementation-Version: 1.0.1 Implementation-Vendor: MartinDeh Create new Deployment Profile Right click on the MySkinProject node, and select New From the New Gallery, select General->Deployment Profiles, Shared Library JAR File from Items, and click OK In the Create Deployment Profile dialog, give name (i.e.mysharedskinlib) and click OK In the Edit JAR Deployment dialog, un-check Include Manifest File option  Select Project Output->Contributors, and check Project Source Path Select Project Output->Filters, ensure that all items under the META-INF folder are selected Click OK to exit the Project Properties dialog Deploy the shared lib to WebLogic (start server before steps) Right click on MySkin Project and select Deploy For this example, I will deploy to JDeverloper WLS In the Deploy dialog, select Deploy to Weblogic Application Server and click Next Choose IntegratedWebLogicServer and click Next Select Deploy to selected instances in the domain radio, select Default Server (note: server must be already started), and ensure Deploy as a shared Library radio is selected Click Finish Open the WebLogic console to see the deployed shared library The following are the steps to create a simple test Portlet Create a new WebCenter Portal - Portlet Producer Application In the Create Portlet Producer dialog, select default settings and click Finish Right click on the Portlets node and select New IIn the New Gallery, select Web-Tier->Portlets, Standards-based Java Portlet (JSR 286) and click OK In the General Portlet information dialog, give portlet name (i.e. MyPortlet) and click Next 2 times, stopping at Step 3 In the Content Types, select the "view" node, in the Implementation Method, select the Generate ADF-Faces JSPX radio and click Finish Once the portlet code is generated, open the view.jspx in the source editor Based on the simple CSS entry, which sets the background color of a panelGroupLayout, replace the <af:form/> tag with the example code <af:form>         <af:panelGroupLayout id="pgl1" styleClass="customPGL">           <af:outputText value="background from shared lib skin" id="ot1"/>         </af:panelGroupLayout>  </af:form> Since this portlet is to use the shared library skin, in the generated trinidad-config.xml, remove both the skin-family tag and the skin-version tag In the Application Resources view, under Descriptors->META-INF, double-click to open the weblogic-application.xml Add a library reference to the shared skin library (note: the library-name must match the extension-name declared in the MANIFEST.MF):  <library-ref>     <library-name>mysharedskin.lib.def</library-name>  </library-ref> Notice that a reference to oracle.webcenter.skin exists.  This is important if this portlet is going to be consumed by a WebCenter Portal application.  If this tag is not present, the portlet skin mismatch will happen.  Configure the portlet for deployment Create Portlet deployment WAR Right click on the Portlets node and select New In the New Gallery, select Deployment Profiles, WAR file from Items and click OK In the Create Deployment Profile dialog, give name (i.e. myportletwar), click OK Keep all of the defaults, however, remember the Context Root entry (i.e. MyPortlet4SharedLib-Portlets-context-root, this will be needed to obtain the producer WSDL URL) Click OK, then OK again to exit from the Properties dialog Since the weblogic-application.xml has to be included in the deployment, the portlet must be deployed as a WAR, within an EAR In the Application dropdown, select Deploy->New Deployment Profile... By default EAR File has been selected, click OK Give Deployment Profile (EAR) a name (i.e. MyPortletProducer) and click OK In the Properties dialog, select Application Assembly and ensure that the myportletwar is checked Keep all of the other defaults and click OK For this demo, un-check the Auto Generate ..., and all of the Security Deployment Options, click OK Save All In the Application dropdown, select Deploy->MyPortletProducer In the Deployment Action, select Deploy to Application Server, click Next Choose IntegratedWebLogicServer and click Next Select Deploy to selected instances in the domain radio, select Default Server (note: server must be already started), and ensure Deploy as a standalone Application radio is selected The select deployment type (identifying the deployment as a JSR 286 portlet) dialog appears.  Keep default radio "Yes" selection and click OK Open the WebLogic console to see the deployed Portlet The last step is to create the test portlet consuming application.  This will be done using the OOTB WebCenter Portal - Framework Application.  Create the Portlet Producer Connection In the JDeveloper Deployment log, copy the URL of the portlet deployment (i.e. http://localhost:7101/MyPortlet4SharedLib-Portlets-context-root Open a browser and paste in the URL.  The Portlet information page should appear.  Click on the WSRP v2 WSDL link Copy the URL from the browser (i.e. http://localhost:7101/MyPortlet4SharedLib-Portlets-context-root/portlets/wsrp2?WSDL) In the Application Resources view, right click on the Connections folder and select New Connection->WSRP Connection Give the producer a name or accept the default, click Next Enter (paste in) the WSDL URL, click Next If connection to Portlet is succesful, Step 3 (Specify Additional ...) should appear.  Accept defaults and click Finish Add the portlet to a test page Open the home.jspx.  Note in the visual editor, the orange dashed border, which identifies the panelCustomizable tag. From the Application Resources. select the MyPortlet portlet node, and drag and drop the node into the panelCustomizable section.  A Confirm Portlet Type dialog appears, keep default ADF Rich Portlet and click OK Configure the portlet to use the shared skin library Open the weblogic-application.xml and add the library-ref entry (mysharedskin.lib.def) for the shared skin library.  See create portlet example above for the steps Since by default, the custom portal using a managed bean to (dynamically) determine the skin family, the default trinidad-config.xml will need to be altered Open the trinidad-config.xml in the editor and replace the EL (preferenceBean) for the skin-family tag, with mysharedskin (this is the skin-family named defined in the trinidad-skins.xml) Remove the skin-version tag Right click on the index.html to test the application   Notice that the JDeveloper log view does not have any reporting of a skin mismatch.  In addition, since I have configured the extra logging outlined in debugging section above, I can see the processed skin jar in both the producer and consumer logs: <SkinUtils> <_getMetaInfSkinsNodeList> Processing skin URL:zip:/JDeveloper/system11.1.1.6.38.61.92/DefaultDomain/servers/DefaultServer/upload/mysharedskin.lib.def/[email protected]/app/mysharedskinlib.jar!/META-INF/trinidad-skins.xml 

  Read the article

• CodePlex Daily Summary for Sunday, June 03, 2012

  CodePlex Daily Summary for Sunday, June 03, 2012Popular ReleasesLiveChat Starter Kit: LCSK v1.5.2: New features: Visitor location (City - Country) from geo-location Pass configuration via javascript for the chat box New visitor identification (no more using the IP address as visitor identification) To update from 1.5.1 Run the /src/1.5.2-sql-updates.txt SQL script to update your database tables. If you have it installed via NuGet, simply update your package and the file will be included so you can run the update script. New installation The easiest way to add LCSK to your app is by...Prime Factorization: Prime Factorization V2: Download the installation package and run it, to install prime factorization on your computer.DNN Content Localization Tools: CLTools v0.4 (Beta4): 3th Beta release for DNN 6.1 and obove Bug corrections : - Copy module work againNTemplates: NTemplates full source code and examples: This release includes the following changes: - NTemplates code. More enhacements and bug fixing. Nested scans seems to be working ok now. New event: ScanStart. Very usuful for calculating totals (see the example) - Examples. 2 new examples on nested scans. One of them very simple I did just for debugging. The other one is a report of invoices grouped by vendor, including totals calculations. Planned Roadmap: - Work on fixing performance bottlenecek: Try to compile the expression...ZXMAK2: Version 2.6.2.3: - add support for ZIP files created on UNIX system; - improve WAV support (fixed PCM24, FLOAT32; added PCM32, FLOAT64); - fix drag-n-drop on modal dialogs; - tape AutoPlay feature (thanks to Woody for algorithm).Net Code Samples: Full WCF Duplex Service Example: Full WCF Duplex Service ExampleKendo UI ASP.NET Sample Applications: Sample Applications (2012-06-01): Sample application(s) demonstrating the use of Kendo UI in ASP.NET applications.Better Explorer: Better Explorer Beta 1: Finally, the first Beta is here! There were a lot of changes, including: Translations into 10 different languages (the translations are not complete and will be updated soon) Conditional Select new tools for managing archives Folder Tools tab new search bar and Search Tab new image editing tools update function many bug fixes, stability fixes, and memory leak fixes other new features as well! Please check it out and if there are any problems, let us know. :) Also, do not forge...myManga: myManga v1.0.0.3: Will include MangaPanda as a default option. ChangeLog Updating from Previous Version: Extract contents of Release - myManga v1.0.0.3.zip to previous version's folder. Replaces: myManga.exe BakaBox.dll CoreMangaClasses.dll Manga.dll Plugins/MangaReader.manga.dll Plugins/MangaFox.manga.dll Plugins/MangaHere.manga.dll Plugins/MangaPanda.manga.dllPlayer Framework by Microsoft: Player Framework for Windows 8 Metro (Preview 3): Player Framework for HTML/JavaScript and XAML/C# Metro Style Applications. Additional DownloadsIIS Smooth Streaming Client SDK for Windows 8 Microsoft PlayReady Client SDK for Metro Style Apps Release notes:Support for Windows 8 Release Preview (released 5/31/12) Advertising support (VAST, MAST, VPAID, & clips) Miscellaneous improvements and bug fixesMicrosoft Ajax Minifier: Microsoft Ajax Minifier 4.54: Fix for issue #18161: pretty-printing CSS @media rule throws an exception due to mismatched Indent/Unindent pair.Silverlight Toolkit: Silverlight 5 Toolkit Source - May 2012: Source code for December 2011 Silverlight 5 Toolkit release.Windows 8 Metro RSS Reader: RSS Reader release 6: Changed background and foreground colors Used VariableSizeGrid layout to wrap blog posts with images Sort items with Images first, text-only last Enabled Caching to improve navigation between framesJson.NET: Json.NET 4.5 Release 6: New feature - Added IgnoreDataMemberAttribute support New feature - Added GetResolvedPropertyName to DefaultContractResolver New feature - Added CheckAdditionalContent to JsonSerializer Change - Metro build now always uses late bound reflection Change - JsonTextReader no longer returns no content after consecutive underlying content read failures Fix - Fixed bad JSON in an array with error handling creating an infinite loop Fix - Fixed deserializing objects with a non-default cons...DotNetNuke® Community Edition CMS: 06.02.00: Major Highlights Fixed issue in the Site Settings when single quotes were being treated as escape characters Fixed issue loading the Mobile Premium Data after upgrading from CE to PE Fixed errors logged when updating folder provider settings Fixed the order of the mobile device capabilities in the Site Redirection Management UI The User Profile page was completely rebuilt. We needed User Profiles to have multiple child pages. This would allow for the most flexibility by still f...????: ????2.0.1: 1、?????。WiX Toolset: WiX v3.6 RC: WiX v3.6 RC (3.6.2928.0) provides feature complete Burn with VS11 support. For more information see Rob's blog post about the release: http://robmensching.com/blog/posts/2012/5/28/WiX-v3.6-Release-Candidate-availableJavascript .NET: Javascript .NET v0.7: SetParameter() reverts to its old behaviour of allowing JavaScript code to add new properties to wrapped C# objects. The behavior added briefly in 0.6 (throws an exception) can be had via the new SetParameterOptions.RejectUnknownProperties. TerminateExecution now uses its isolate to terminate the correct context automatically. Added support for converting all C# integral types, decimal and enums to JavaScript numbers. (Previously only the common types were handled properly.) Bug fixe...Phalanger - The PHP Language Compiler for the .NET Framework: 3.0 (May 2012): Fixes: unserialize() of negative float numbers fix pcre possesive quantifiers and character class containing ()[] array deserilization when the array contains a reference to ISerializable parsing lambda function fix round() reimplemented as it is in PHP to avoid .NET rounding errors filesize bypass for FileInfo.Length bug in Mono New features: Time zones reimplemented, uses Windows/Linux databaseSharePoint Euro 2012 - UEFA European Football Predictor: havivi.euro2012.wsp (1.1): New fetures:Admin enable / disable match Hide/Show Euro 2012 SharePoint lists (3 lists) Installing SharePoint Euro 2012 PredictorSharePoint Euro 2012 Predictor has been developed as a SharePoint Sandbox solution to support SharePoint Online (Office 365) Download the solution havivi.euro2012.wsp from the download page: Downloads Upload this solution to your Site Collection via the solutions area. Click on Activate to make the web parts in the solution available for use in the Site C...New ProjectsAFS.PhonePusherConnectorVX: pusher for phone vxApache: this is the Apache project.Apple: this is the Apple project.CUARTOAZZJL: HURRA!!Designing Windows 8 Applications with C# and XAML: This project hosts the source code used in the example projects for the book, Designing Windows 8 Metro Applications with C# and XAML.Easy Internet: CyberWeb ist ein einfacher Webbrowser für PC Neulinge. Ideal für Leute, die noch keine PC-Erfahrung haben.Easy Outlook Backup: Beschreibung: Easy Outlook Backup ist ein Programm das alle Daten von Outlook sichert. Ideal für Leute, die noch keine PC-Erfahrung haben. Easy Realtime Start: Beschreibung: Easy Realtime Start ist ein Programm das einen Prozess in höchster Priorität startet. Und das ganz bequem Per drag & drop. Ideal für Leute, die aufwendige Programme starten müssen. (zB.: “Blender” Free 3D Designer)eStock: eStock ist ein Verwaltungstool für Elektroniker um Bauteile im "Lager" sowie Projekte zu verwalten. Es bietet eine Möglichkeit festzulegen, um welche Art von Bauteil es sich handelt und wo sich dieses im Lager bzw. Regal befindet. Die Projektverwaltung ermöglicht es, Bauteile einem Projekt hinzuzufügen und eine Bestellliste / Einkaufsliste von Bauteilen, die nicht mehr im Lager vorhanden sind, zu erstellen. FuTTY: FireEgl's PuTTY -- FuTTY! FuTTY is a fork of PuTTY and PuTTYTray.GeometryWorld: To Do...Google: this is the Google project.Google Advance Search: An easy way to create documents search at Google and read your emails and Much moregoogle maps viewer for dynamics crm 2011: Easy google maps viewer for dynamics CRM 2011GPS Status - (GPS tool für GPS-Dongles und Mäuse) - GPS-Empfänger: Mein Programm verbindet sich mit dem externen GPS über einen Com-Port und bietet verschiedene Tools.Harmony Text Editor: Harmony is a ridiculously simple text editor for code and poetry.Hi! Football: .Goal / Objective -> To help friends gather for enjoying watching football together. .How it works -> To basically choose your favorite team, choose one of the matches fetched for his team, our app will generate a list of popular restraunts, cafes where he can watch the chosen match, the user can select one of the generated locations around his area, and create an event inviting his friends to join him and he can also join other friends' events.Java: this is the Java project.LevelUp Serializer: LevelUp Serializer is a small and simple serialize library.It can help developer to serialize and deserialize data more convenient. Feature: - Ease of use - Supports almost all serializer, like Binary、Xml、Soap、Json、DataContract. - Support serialize to file、serialize to stream、deserialize from file、deserialize from stream. - Support Xml encryption. - Support accelerated through the XML the serialization assemble.LFormatConvert: ????Linux???????????????????????，??ffmpeg????Machine QA Manager: Machine QA Manager is intended to save and help trend results from radiation therapy equipment testing. The program will be made as generic as possible from a initial setup to enable it's use for other types of routine testing activities (for example factory equipment) but preconfigured templates for radiation therapy will be supplied for the convenience of people working in that domain.maven-asbuild-plugin: maven-asbuild-plugin incorporates the adobe flash/flex based artifacts like swc or swf into the maven methology.Midnight Peach - C# framework generator for LINQ: C# framework generator for LINQMiku???????: ????????，????????！?????????????，??????????。?????????????????！MIKU????????????，??！????????????、????。 This program used to detect music beat.You can listen to music while press button,and it can display the BPM of the song.Miku will wave to you.MyTestingStudy: my personal testing studyNameless Sprite Editor: Nameless Sprite Editor is a tool used to thoroughly edit the graphics in ALL Game Boy Advance games. [ UNDER CONSTRUCTION ]NeoModulus Business Rules Builder: A windows form application that allows non-programmers to build strict definitions of a business domain. Once the definition is complete the program will build out object oriented C# files and a .net DLL. My test business domain is the open SRD, basically Dungeons and Dragons 3.5 edition.NodeJs: this is the NodeJs projectNoSQL: this is the Nosql project.OmniKassa for NopCommerce: OmniKassa payment module plugin for nopCommerceOn-Line Therapy: testOpen School: This project is about to create an open platform for all the academic institutions, so that they can manage all of their work. Our efforts will be for every kind of institution who are currently struggling with different kind of systems in place which are not collaborating with each other. This project will provide a common platform to all these kind of systems and provide them a better solution which actually works. Oracle: this is the Oracle project.Orchard Web Services: RESTful web services to expose interaction with Orchard content management.Personal Social Network using asp.net mvc and mongodb: FirstRooster is a network platform that let user create their own social network of interest to connect and share with like minded people anywhere.peshop: E-Commerce application , separated by DAl,BLL and Presentation layersPHP: this is the PHP project.Prime Factorization: Factoring trinomials using the ac method can be made easier through the use of Prime Factorization. Prime Factorization is a program that can assist you in the factoring of numbers in Algebra, namely trinomials using the AC Method. It can also find all the factors of any number.PromedioNotas: El programa trata de promediar 3 nostas y mostrar y si pasaba de año o no por medio de un mensajeProyecto Tarea: Este proyecto esta hecho con el objetivo de aprender sobre TFSProyectotarea1: Sotfware de terminal aéreo de Guayaquil, donde se encuentran el nombre de las aerolíneas y las rutas de vuelo a nivel nacional.Python: this is the Python project.Ruby: this is the Ruby project.tedplay: tedplay is your media player of choice for playing Commodore 264 music format files similar to SIDplay. It is basically a stripped down Commodore plus/4 emulator without video output and peripherals based on the SDL build of the Commodore 264 family emulator YAPE. tedplay is released under version 2 of the GNU Generic Public License and can be built for both Windows and Unix or actually any platform that has a C++ compiler and SDL support.test1: This is a test projectwin-x264: A port of the x264-codebase into a VisualStudio-project. Compilation requires Intel-compiler and Yasm.XDA ROM Hub: Xperia 2011 line toolkit.znvicente_cuartoc: Poyecto Vicente Eduardo Zambrano Navarrete??Win7?????: ??????? *.theme ???????（??，??，??，???）。????VSB???*.msstyles??，????????，????????????????????????！????????????，?????????????。???，????????！ ?????????，?????????，????????，??????！?????????????，?????????????????，?????????，???Aero??，??????~?????????????！??，?????????theme??，?????????，??????，????，??????。 This program used to create .theme file and the relevant documents (wallpaper, pointer, ICONS, sounds, etc.). As long as you use VSB ready . msstyles files, chosen the icon wallpaper, etc, an...

  Read the article

• How do you setup the driver for a Philips based TV capture card?

  - by user8270

  Hi, I have a TV card that I have not managed to install with Ubuntu 10.10 i386. I have tried various topics in various forums and I could not install it. I hope you can help me to install it thank you. lspci 01:07.0 Multimedia controller: Philips Semiconductors SAA7130 Video Broadcast Decoder (rev 01) dmesg [10299.516344] saa7134 ALSA driver for DMA sound unloaded [11385.340661] Linux video capture interface: v2.00 [11385.384278] saa7130/34: v4l2 driver version 0.2.16 loaded [11385.384390] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [11385.384403] saa7130[0]: subsystem: 1131:0000, board: LifeView/Typhoon FlyVIDEO2000 [card=3,insmod option] [11385.384412] saa7130[0]: can't get MMIO memory @ 0x0 [11385.384431] saa7134: probe of 0000:01:07.0 failed with error -16 [11385.401174] saa7134 ALSA driver for DMA sound loaded [11385.401182] saa7134 ALSA: no saa7134 cards found [11477.797019] tvtime[12534]: segfault at 6b0 ip 0804cf64 sp bf928a4c error 4 in tvtime[8048000+76000] [11626.141821] tvtime[12549]: segfault at 6b0 ip 0804cf64 sp bfec357c error 4 in tvtime[8048000+76000] [12218.120632] saa7134 ALSA driver for DMA sound unloaded [12464.993061] Linux video capture interface: v2.00 [12465.028285] saa7130/34: v4l2 driver version 0.2.16 loaded [12465.028392] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [12465.028404] saa7134: <rant> [12465.028406] saa7134: Congratulations! Your TV card vendor saved a few [12465.028408] saa7134: cents for a eeprom, thus your pci board has no [12465.028411] saa7134: subsystem ID and I can't identify it automatically [12465.028414] saa7134: </rant> [12465.028416] saa7134: I feel better now. Ok, here are the good news: [12465.028418] saa7134: You can use the card=<nr> insmod option to specify [12465.028421] saa7134: which board do you have. The list: [12465.028428] saa7134: card=0 -> UNKNOWN/GENERIC [12465.028435] saa7134: card=1 -> Proteus Pro [philips reference design] 1131:2001 1131:2001 [12465.028447] saa7134: card=2 -> LifeView FlyVIDEO3000 5168:0138 4e42:0138 [12465.028457] saa7134: card=3 -> LifeView/Typhoon FlyVIDEO2000 5168:0138 4e42:0138 [12465.028467] saa7134: card=4 -> EMPRESS 1131:6752 [12465.028475] saa7134: card=5 -> SKNet Monster TV 1131:4e85 [12465.028484] saa7134: card=6 -> Tevion MD 9717 [12465.028491] saa7134: card=7 -> KNC One TV-Station RDS / Typhoon TV Tune 1131:fe01 1894:fe01 [12465.028501] saa7134: card=8 -> Terratec Cinergy 400 TV 153b:1142 [12465.028510] saa7134: card=9 -> Medion 5044 [12465.028517] saa7134: card=10 -> Kworld/KuroutoShikou SAA7130-TVPCI [12465.028523] saa7134: card=11 -> Terratec Cinergy 600 TV 153b:1143 [12465.028532] saa7134: card=12 -> Medion 7134 16be:0003 16be:5000 [12465.028542] saa7134: card=13 -> Typhoon TV+Radio 90031 [12465.028548] saa7134: card=14 -> ELSA EX-VISION 300TV 1048:226b [12465.028557] saa7134: card=15 -> ELSA EX-VISION 500TV 1048:226a [12465.028565] saa7134: card=16 -> ASUS TV-FM 7134 1043:4842 1043:4830 1043:4840 [12465.028576] saa7134: card=17 -> AOPEN VA1000 POWER 1131:7133 [12465.028585] saa7134: card=18 -> BMK MPEX No Tuner [12465.028592] saa7134: card=19 -> Compro VideoMate TV 185b:c100 [12465.028600] saa7134: card=20 -> Matrox CronosPlus 102b:48d0 [12465.028608] saa7134: card=21 -> 10MOONS PCI TV CAPTURE CARD 1131:2001 [12465.028617] saa7134: card=22 -> AverMedia M156 / Medion 2819 1461:a70b [12465.028625] saa7134: card=23 -> BMK MPEX Tuner [12465.028632] saa7134: card=24 -> KNC One TV-Station DVR 1894:a006 [12465.028640] saa7134: card=25 -> ASUS TV-FM 7133 1043:4843 [12465.028648] saa7134: card=26 -> Pinnacle PCTV Stereo (saa7134) 11bd:002b [12465.028657] saa7134: card=27 -> Manli MuchTV M-TV002 [12465.028663] saa7134: card=28 -> Manli MuchTV M-TV001 [12465.028670] saa7134: card=29 -> Nagase Sangyo TransGear 3000TV 1461:050c [12465.028679] saa7134: card=30 -> Elitegroup ECS TVP3XP FM1216 Tuner Card( 1019:4cb4 [12465.028687] saa7134: card=31 -> Elitegroup ECS TVP3XP FM1236 Tuner Card 1019:4cb5 [12465.028695] saa7134: card=32 -> AVACS SmartTV [12465.028702] saa7134: card=33 -> AVerMedia DVD EZMaker 1461:10ff [12465.028710] saa7134: card=34 -> Noval Prime TV 7133 [12465.028717] saa7134: card=35 -> AverMedia AverTV Studio 305 1461:2115 [12465.028725] saa7134: card=36 -> UPMOST PURPLE TV 12ab:0800 [12465.028734] saa7134: card=37 -> Items MuchTV Plus / IT-005 [12465.028740] saa7134: card=38 -> Terratec Cinergy 200 TV 153b:1152 [12465.028749] saa7134: card=39 -> LifeView FlyTV Platinum Mini 5168:0212 4e42:0212 5169:1502 [12465.028760] saa7134: card=40 -> Compro VideoMate TV PVR/FM 185b:c100 [12465.028768] saa7134: card=41 -> Compro VideoMate TV Gold+ 185b:c100 [12465.028776] saa7134: card=42 -> Sabrent SBT-TVFM (saa7130) [12465.028783] saa7134: card=43 -> :Zolid Xpert TV7134 [12465.028790] saa7134: card=44 -> Empire PCI TV-Radio LE [12465.028796] saa7134: card=45 -> Avermedia AVerTV Studio 307 1461:9715 [12465.028805] saa7134: card=46 -> AVerMedia Cardbus TV/Radio (E500) 1461:d6ee [12465.028813] saa7134: card=47 -> Terratec Cinergy 400 mobile 153b:1162 [12465.028821] saa7134: card=48 -> Terratec Cinergy 600 TV MK3 153b:1158 [12465.028830] saa7134: card=49 -> Compro VideoMate Gold+ Pal 185b:c200 [12465.028838] saa7134: card=50 -> Pinnacle PCTV 300i DVB-T + PAL 11bd:002d [12465.028847] saa7134: card=51 -> ProVideo PV952 1540:9524 [12465.028855] saa7134: card=52 -> AverMedia AverTV/305 1461:2108 [12465.028863] saa7134: card=53 -> ASUS TV-FM 7135 1043:4845 [12465.028871] saa7134: card=54 -> LifeView FlyTV Platinum FM / Gold 5168:0214 5168:5214 1489:0214 5168:0304 [12465.028884] saa7134: card=55 -> LifeView FlyDVB-T DUO / MSI TV@nywhere D 5168:0306 4e42:0306 [12465.028894] saa7134: card=56 -> Avermedia AVerTV 307 1461:a70a [12465.028903] saa7134: card=57 -> Avermedia AVerTV GO 007 FM 1461:f31f [12465.028911] saa7134: card=58 -> ADS Tech Instant TV (saa7135) 1421:0350 1421:0351 1421:0370 1421:1370 [12465.028924] saa7134: card=59 -> Kworld/Tevion V-Stream Xpert TV PVR7134 [12465.028931] saa7134: card=60 -> LifeView/Typhoon/Genius FlyDVB-T Duo Car 5168:0502 4e42:0502 1489:0502 [12465.028942] saa7134: card=61 -> Philips TOUGH DVB-T reference design 1131:2004 [12465.028951] saa7134: card=62 -> Compro VideoMate TV Gold+II [12465.028958] saa7134: card=63 -> Kworld Xpert TV PVR7134 [12465.028964] saa7134: card=64 -> FlyTV mini Asus Digimatrix 1043:0210 [12465.028973] saa7134: card=65 -> V-Stream Studio TV Terminator [12465.028980] saa7134: card=66 -> Yuan TUN-900 (saa7135) [12465.028986] saa7134: card=67 -> Beholder BeholdTV 409 FM 0000:4091 [12465.028995] saa7134: card=68 -> GoTView 7135 PCI 5456:7135 [12465.029003] saa7134: card=69 -> Philips EUROPA V3 reference design 1131:2004 [12465.029011] saa7134: card=70 -> Compro Videomate DVB-T300 185b:c900 [12465.029020] saa7134: card=71 -> Compro Videomate DVB-T200 185b:c901 [12465.029028] saa7134: card=72 -> RTD Embedded Technologies VFG7350 1435:7350 [12465.029036] saa7134: card=73 -> RTD Embedded Technologies VFG7330 1435:7330 [12465.029045] saa7134: card=74 -> LifeView FlyTV Platinum Mini2 14c0:1212 [12465.029053] saa7134: card=75 -> AVerMedia AVerTVHD MCE A180 1461:1044 [12465.029062] saa7134: card=76 -> SKNet MonsterTV Mobile 1131:4ee9 [12465.029070] saa7134: card=77 -> Pinnacle PCTV 40i/50i/110i (saa7133) 11bd:002e [12465.029078] saa7134: card=78 -> ASUSTeK P7131 Dual 1043:4862 [12465.029087] saa7134: card=79 -> Sedna/MuchTV PC TV Cardbus TV/Radio (ITO [12465.029094] saa7134: card=80 -> ASUS Digimatrix TV 1043:0210 [12465.029102] saa7134: card=81 -> Philips Tiger reference design 1131:2018 [12465.029110] saa7134: card=82 -> MSI TV@Anywhere plus 1462:6231 1462:8624 [12465.029120] saa7134: card=83 -> Terratec Cinergy 250 PCI TV 153b:1160 [12465.029128] saa7134: card=84 -> LifeView FlyDVB Trio 5168:0319 [12465.029137] saa7134: card=85 -> AverTV DVB-T 777 1461:2c05 1461:2c05 [12465.029147] saa7134: card=86 -> LifeView FlyDVB-T / Genius VideoWonder D 5168:0301 1489:0301 [12465.029156] saa7134: card=87 -> ADS Instant TV Duo Cardbus PTV331 0331:1421 [12465.029165] saa7134: card=88 -> Tevion/KWorld DVB-T 220RF 17de:7201 [12465.029173] saa7134: card=89 -> ELSA EX-VISION 700TV 1048:226c [12465.029182] saa7134: card=90 -> Kworld ATSC110/115 17de:7350 17de:7352 [12465.029191] saa7134: card=91 -> AVerMedia A169 B 1461:7360 [12465.029200] saa7134: card=92 -> AVerMedia A169 B1 1461:6360 [12465.029208] saa7134: card=93 -> Medion 7134 Bridge #2 16be:0005 [12465.029216] saa7134: card=94 -> LifeView FlyDVB-T Hybrid Cardbus/MSI TV 5168:3306 5168:3502 5168:3307 4e42:3502 [12465.029229] saa7134: card=95 -> LifeView FlyVIDEO3000 (NTSC) 5169:0138 [12465.029238] saa7134: card=96 -> Medion Md8800 Quadro 16be:0007 16be:0008 16be:000d [12465.029249] saa7134: card=97 -> LifeView FlyDVB-S /Acorp TV134DS 5168:0300 4e42:0300 [12465.029259] saa7134: card=98 -> Proteus Pro 2309 0919:2003 [12465.029267] saa7134: card=99 -> AVerMedia TV Hybrid A16AR 1461:2c00 [12465.029276] saa7134: card=100 -> Asus Europa2 OEM 1043:4860 [12465.029284] saa7134: card=101 -> Pinnacle PCTV 310i 11bd:002f [12465.029293] saa7134: card=102 -> Avermedia AVerTV Studio 507 1461:9715 [12465.029301] saa7134: card=103 -> Compro Videomate DVB-T200A [12465.029308] saa7134: card=104 -> Hauppauge WinTV-HVR1110 DVB-T/Hybrid 0070:6700 0070:6701 0070:6702 0070:6703 0070:6704 0070:6705 [12465.029324] saa7134: card=105 -> Terratec Cinergy HT PCMCIA 153b:1172 [12465.029332] saa7134: card=106 -> Encore ENLTV 1131:2342 1131:2341 3016:2344 [12465.029344] saa7134: card=107 -> Encore ENLTV-FM 1131:230f [12465.029352] saa7134: card=108 -> Terratec Cinergy HT PCI 153b:1175 [12465.029360] saa7134: card=109 -> Philips Tiger - S Reference design [12465.029367] saa7134: card=110 -> Avermedia M102 1461:f31e [12465.029375] saa7134: card=111 -> ASUS P7131 4871 1043:4871 [12465.029384] saa7134: card=112 -> ASUSTeK P7131 Hybrid 1043:4876 [12465.029392] saa7134: card=113 -> Elitegroup ECS TVP3XP FM1246 Tuner Card 1019:4cb6 [12465.029401] saa7134: card=114 -> KWorld DVB-T 210 17de:7250 [12465.029409] saa7134: card=115 -> Sabrent PCMCIA TV-PCB05 0919:2003 [12465.029418] saa7134: card=116 -> 10MOONS TM300 TV Card 1131:2304 [12465.029426] saa7134: card=117 -> Avermedia Super 007 1461:f01d [12465.029435] saa7134: card=118 -> Beholder BeholdTV 401 0000:4016 [12465.029443] saa7134: card=119 -> Beholder BeholdTV 403 0000:4036 [12465.029451] saa7134: card=120 -> Beholder BeholdTV 403 FM 0000:4037 [12465.029459] saa7134: card=121 -> Beholder BeholdTV 405 0000:4050 [12465.029468] saa7134: card=122 -> Beholder BeholdTV 405 FM 0000:4051 [12465.029476] saa7134: card=123 -> Beholder BeholdTV 407 0000:4070 [12465.029484] saa7134: card=124 -> Beholder BeholdTV 407 FM 0000:4071 [12465.029493] saa7134: card=125 -> Beholder BeholdTV 409 0000:4090 [12465.029501] saa7134: card=126 -> Beholder BeholdTV 505 FM 5ace:5050 [12465.029510] saa7134: card=127 -> Beholder BeholdTV 507 FM / BeholdTV 509 5ace:5070 5ace:5090 [12465.029520] saa7134: card=128 -> Beholder BeholdTV Columbus TVFM 0000:5201 [12465.029528] saa7134: card=129 -> Beholder BeholdTV 607 FM 5ace:6070 [12465.029537] saa7134: card=130 -> Beholder BeholdTV M6 5ace:6190 [12465.029545] saa7134: card=131 -> Twinhan Hybrid DTV-DVB 3056 PCI 1822:0022 [12465.029554] saa7134: card=132 -> Genius TVGO AM11MCE [12465.029560] saa7134: card=133 -> NXP Snake DVB-S reference design [12465.029567] saa7134: card=134 -> Medion/Creatix CTX953 Hybrid 16be:0010 [12465.029576] saa7134: card=135 -> MSI TV@nywhere A/D v1.1 1462:8625 [12465.029584] saa7134: card=136 -> AVerMedia Cardbus TV/Radio (E506R) 1461:f436 [12465.029592] saa7134: card=137 -> AVerMedia Hybrid TV/Radio (A16D) 1461:f936 [12465.029601] saa7134: card=138 -> Avermedia M115 1461:a836 [12465.029609] saa7134: card=139 -> Compro VideoMate T750 185b:c900 [12465.029617] saa7134: card=140 -> Avermedia DVB-S Pro A700 1461:a7a1 [12465.029626] saa7134: card=141 -> Avermedia DVB-S Hybrid+FM A700 1461:a7a2 [12465.029634] saa7134: card=142 -> Beholder BeholdTV H6 5ace:6290 [12465.029642] saa7134: card=143 -> Beholder BeholdTV M63 5ace:6191 [12465.029651] saa7134: card=144 -> Beholder BeholdTV M6 Extra 5ace:6193 [12465.029659] saa7134: card=145 -> AVerMedia MiniPCI DVB-T Hybrid M103 1461:f636 1461:f736 [12465.029669] saa7134: card=146 -> ASUSTeK P7131 Analog [12465.029676] saa7134: card=147 -> Asus Tiger 3in1 1043:4878 [12465.029684] saa7134: card=148 -> Encore ENLTV-FM v5.3 1a7f:2008 [12465.029693] saa7134: card=149 -> Avermedia PCI pure analog (M135A) 1461:f11d [12465.029701] saa7134: card=150 -> Zogis Real Angel 220 [12465.029708] saa7134: card=151 -> ADS Tech Instant HDTV 1421:0380 [12465.029716] saa7134: card=152 -> Asus Tiger Rev:1.00 1043:4857 [12465.029725] saa7134: card=153 -> Kworld Plus TV Analog Lite PCI 17de:7128 [12465.029733] saa7134: card=154 -> Avermedia AVerTV GO 007 FM Plus 1461:f31d [12465.029742] saa7134: card=155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid 0070:6706 0070:6708 [12465.029752] saa7134: card=156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid 0070:6707 0070:6709 0070:670a [12465.029763] saa7134: card=157 -> Avermedia AVerTV Studio 507UA 1461:a11b [12465.029772] saa7134: card=158 -> AVerMedia Cardbus TV/Radio (E501R) 1461:b7e9 [12465.029780] saa7134: card=159 -> Beholder BeholdTV 505 RDS 0000:505b [12465.029789] saa7134: card=160 -> Beholder BeholdTV 507 RDS 0000:5071 [12465.029797] saa7134: card=161 -> Beholder BeholdTV 507 RDS 0000:507b [12465.029806] saa7134: card=162 -> Beholder BeholdTV 607 FM 5ace:6071 [12465.029815] saa7134: card=163 -> Beholder BeholdTV 609 FM 5ace:6090 [12465.029823] saa7134: card=164 -> Beholder BeholdTV 609 FM 5ace:6091 [12465.029832] saa7134: card=165 -> Beholder BeholdTV 607 RDS 5ace:6072 [12465.029840] saa7134: card=166 -> Beholder BeholdTV 607 RDS 5ace:6073 [12465.029849] saa7134: card=167 -> Beholder BeholdTV 609 RDS 5ace:6092 [12465.029857] saa7134: card=168 -> Beholder BeholdTV 609 RDS 5ace:6093 [12465.029866] saa7134: card=169 -> Compro VideoMate S350/S300 185b:c900 [12465.029874] saa7134: card=170 -> AverMedia AverTV Studio 505 1461:a115 [12465.029883] saa7134: card=171 -> Beholder BeholdTV X7 5ace:7595 [12465.029892] saa7134: card=172 -> RoverMedia TV Link Pro FM 19d1:0138 [12465.029900] saa7134: card=173 -> Zolid Hybrid TV Tuner PCI 1131:2004 [12465.029909] saa7134: card=174 -> Asus Europa Hybrid OEM 1043:4847 [12465.029917] saa7134: card=175 -> Leadtek Winfast DTV1000S 107d:6655 [12465.029926] saa7134: card=176 -> Beholder BeholdTV 505 RDS 0000:5051 [12465.029934] saa7134: card=177 -> Hawell HW-404M7 [12465.029941] saa7134: card=178 -> Beholder BeholdTV H7 [12465.029948] saa7134: card=179 -> Beholder BeholdTV A7 [12465.029955] saa7134: card=180 -> Avermedia PCI M733A 1461:4155 1461:4255 [12465.029967] saa7130[0]: subsystem: 1131:0000, board: UNKNOWN/GENERIC [card=0,autodetected] [12465.030033] saa7130[0]: can't get MMIO memory @ 0x0 [12465.030051] saa7134: probe of 0000:01:07.0 failed with error -16 [12465.053892] saa7134 ALSA driver for DMA sound loaded [12465.053900] saa7134 ALSA: no saa7134 cards found tvtime-scanner Leyendo la configuración de /etc/tvtime/tvtime.xml Leyendo la configuración de /home/ricardo/.tvtime/tvtime.xml Escaneando usando la norma de TV NTSC. /home/ricardo/.tvtime/stationlist.xml: No existing NTSC station list "Custom". videoinput: Cannot open capture device /dev/video0: No existe el dispositivo o la dirección

  Read the article

• Problems with capture TV card

  - by user8270

  Hi, I have a TV card that I have not managed to install with Ubuntu 10.10 i386. I have tried various topics in various forums and I could not install it. I hope you can help me to install it thank you. lspci 01:07.0 Multimedia controller: Philips Semiconductors SAA7130 Video Broadcast Decoder (rev 01) dmesg [10299.516344] saa7134 ALSA driver for DMA sound unloaded [11385.340661] Linux video capture interface: v2.00 [11385.384278] saa7130/34: v4l2 driver version 0.2.16 loaded [11385.384390] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [11385.384403] saa7130[0]: subsystem: 1131:0000, board: LifeView/Typhoon FlyVIDEO2000 [card=3,insmod option] [11385.384412] saa7130[0]: can't get MMIO memory @ 0x0 [11385.384431] saa7134: probe of 0000:01:07.0 failed with error -16 [11385.401174] saa7134 ALSA driver for DMA sound loaded [11385.401182] saa7134 ALSA: no saa7134 cards found [11477.797019] tvtime[12534]: segfault at 6b0 ip 0804cf64 sp bf928a4c error 4 in tvtime[8048000+76000] [11626.141821] tvtime[12549]: segfault at 6b0 ip 0804cf64 sp bfec357c error 4 in tvtime[8048000+76000] [12218.120632] saa7134 ALSA driver for DMA sound unloaded [12464.993061] Linux video capture interface: v2.00 [12465.028285] saa7130/34: v4l2 driver version 0.2.16 loaded [12465.028392] saa7130[0]: found at 0000:01:07.0, rev: 1, irq: 17, latency: 32, mmio: 0x0 [12465.028404] saa7134: <rant> [12465.028406] saa7134: Congratulations! Your TV card vendor saved a few [12465.028408] saa7134: cents for a eeprom, thus your pci board has no [12465.028411] saa7134: subsystem ID and I can't identify it automatically [12465.028414] saa7134: </rant> [12465.028416] saa7134: I feel better now. Ok, here are the good news: [12465.028418] saa7134: You can use the card=<nr> insmod option to specify [12465.028421] saa7134: which board do you have. The list: [12465.028428] saa7134: card=0 -> UNKNOWN/GENERIC [12465.028435] saa7134: card=1 -> Proteus Pro [philips reference design] 1131:2001 1131:2001 [12465.028447] saa7134: card=2 -> LifeView FlyVIDEO3000 5168:0138 4e42:0138 [12465.028457] saa7134: card=3 -> LifeView/Typhoon FlyVIDEO2000 5168:0138 4e42:0138 [12465.028467] saa7134: card=4 -> EMPRESS 1131:6752 [12465.028475] saa7134: card=5 -> SKNet Monster TV 1131:4e85 [12465.028484] saa7134: card=6 -> Tevion MD 9717 [12465.028491] saa7134: card=7 -> KNC One TV-Station RDS / Typhoon TV Tune 1131:fe01 1894:fe01 [12465.028501] saa7134: card=8 -> Terratec Cinergy 400 TV 153b:1142 [12465.028510] saa7134: card=9 -> Medion 5044 [12465.028517] saa7134: card=10 -> Kworld/KuroutoShikou SAA7130-TVPCI [12465.028523] saa7134: card=11 -> Terratec Cinergy 600 TV 153b:1143 [12465.028532] saa7134: card=12 -> Medion 7134 16be:0003 16be:5000 [12465.028542] saa7134: card=13 -> Typhoon TV+Radio 90031 [12465.028548] saa7134: card=14 -> ELSA EX-VISION 300TV 1048:226b [12465.028557] saa7134: card=15 -> ELSA EX-VISION 500TV 1048:226a [12465.028565] saa7134: card=16 -> ASUS TV-FM 7134 1043:4842 1043:4830 1043:4840 [12465.028576] saa7134: card=17 -> AOPEN VA1000 POWER 1131:7133 [12465.028585] saa7134: card=18 -> BMK MPEX No Tuner [12465.028592] saa7134: card=19 -> Compro VideoMate TV 185b:c100 [12465.028600] saa7134: card=20 -> Matrox CronosPlus 102b:48d0 [12465.028608] saa7134: card=21 -> 10MOONS PCI TV CAPTURE CARD 1131:2001 [12465.028617] saa7134: card=22 -> AverMedia M156 / Medion 2819 1461:a70b [12465.028625] saa7134: card=23 -> BMK MPEX Tuner [12465.028632] saa7134: card=24 -> KNC One TV-Station DVR 1894:a006 [12465.028640] saa7134: card=25 -> ASUS TV-FM 7133 1043:4843 [12465.028648] saa7134: card=26 -> Pinnacle PCTV Stereo (saa7134) 11bd:002b [12465.028657] saa7134: card=27 -> Manli MuchTV M-TV002 [12465.028663] saa7134: card=28 -> Manli MuchTV M-TV001 [12465.028670] saa7134: card=29 -> Nagase Sangyo TransGear 3000TV 1461:050c [12465.028679] saa7134: card=30 -> Elitegroup ECS TVP3XP FM1216 Tuner Card( 1019:4cb4 [12465.028687] saa7134: card=31 -> Elitegroup ECS TVP3XP FM1236 Tuner Card 1019:4cb5 [12465.028695] saa7134: card=32 -> AVACS SmartTV [12465.028702] saa7134: card=33 -> AVerMedia DVD EZMaker 1461:10ff [12465.028710] saa7134: card=34 -> Noval Prime TV 7133 [12465.028717] saa7134: card=35 -> AverMedia AverTV Studio 305 1461:2115 [12465.028725] saa7134: card=36 -> UPMOST PURPLE TV 12ab:0800 [12465.028734] saa7134: card=37 -> Items MuchTV Plus / IT-005 [12465.028740] saa7134: card=38 -> Terratec Cinergy 200 TV 153b:1152 [12465.028749] saa7134: card=39 -> LifeView FlyTV Platinum Mini 5168:0212 4e42:0212 5169:1502 [12465.028760] saa7134: card=40 -> Compro VideoMate TV PVR/FM 185b:c100 [12465.028768] saa7134: card=41 -> Compro VideoMate TV Gold+ 185b:c100 [12465.028776] saa7134: card=42 -> Sabrent SBT-TVFM (saa7130) [12465.028783] saa7134: card=43 -> :Zolid Xpert TV7134 [12465.028790] saa7134: card=44 -> Empire PCI TV-Radio LE [12465.028796] saa7134: card=45 -> Avermedia AVerTV Studio 307 1461:9715 [12465.028805] saa7134: card=46 -> AVerMedia Cardbus TV/Radio (E500) 1461:d6ee [12465.028813] saa7134: card=47 -> Terratec Cinergy 400 mobile 153b:1162 [12465.028821] saa7134: card=48 -> Terratec Cinergy 600 TV MK3 153b:1158 [12465.028830] saa7134: card=49 -> Compro VideoMate Gold+ Pal 185b:c200 [12465.028838] saa7134: card=50 -> Pinnacle PCTV 300i DVB-T + PAL 11bd:002d [12465.028847] saa7134: card=51 -> ProVideo PV952 1540:9524 [12465.028855] saa7134: card=52 -> AverMedia AverTV/305 1461:2108 [12465.028863] saa7134: card=53 -> ASUS TV-FM 7135 1043:4845 [12465.028871] saa7134: card=54 -> LifeView FlyTV Platinum FM / Gold 5168:0214 5168:5214 1489:0214 5168:0304 [12465.028884] saa7134: card=55 -> LifeView FlyDVB-T DUO / MSI TV@nywhere D 5168:0306 4e42:0306 [12465.028894] saa7134: card=56 -> Avermedia AVerTV 307 1461:a70a [12465.028903] saa7134: card=57 -> Avermedia AVerTV GO 007 FM 1461:f31f [12465.028911] saa7134: card=58 -> ADS Tech Instant TV (saa7135) 1421:0350 1421:0351 1421:0370 1421:1370 [12465.028924] saa7134: card=59 -> Kworld/Tevion V-Stream Xpert TV PVR7134 [12465.028931] saa7134: card=60 -> LifeView/Typhoon/Genius FlyDVB-T Duo Car 5168:0502 4e42:0502 1489:0502 [12465.028942] saa7134: card=61 -> Philips TOUGH DVB-T reference design 1131:2004 [12465.028951] saa7134: card=62 -> Compro VideoMate TV Gold+II [12465.028958] saa7134: card=63 -> Kworld Xpert TV PVR7134 [12465.028964] saa7134: card=64 -> FlyTV mini Asus Digimatrix 1043:0210 [12465.028973] saa7134: card=65 -> V-Stream Studio TV Terminator [12465.028980] saa7134: card=66 -> Yuan TUN-900 (saa7135) [12465.028986] saa7134: card=67 -> Beholder BeholdTV 409 FM 0000:4091 [12465.028995] saa7134: card=68 -> GoTView 7135 PCI 5456:7135 [12465.029003] saa7134: card=69 -> Philips EUROPA V3 reference design 1131:2004 [12465.029011] saa7134: card=70 -> Compro Videomate DVB-T300 185b:c900 [12465.029020] saa7134: card=71 -> Compro Videomate DVB-T200 185b:c901 [12465.029028] saa7134: card=72 -> RTD Embedded Technologies VFG7350 1435:7350 [12465.029036] saa7134: card=73 -> RTD Embedded Technologies VFG7330 1435:7330 [12465.029045] saa7134: card=74 -> LifeView FlyTV Platinum Mini2 14c0:1212 [12465.029053] saa7134: card=75 -> AVerMedia AVerTVHD MCE A180 1461:1044 [12465.029062] saa7134: card=76 -> SKNet MonsterTV Mobile 1131:4ee9 [12465.029070] saa7134: card=77 -> Pinnacle PCTV 40i/50i/110i (saa7133) 11bd:002e [12465.029078] saa7134: card=78 -> ASUSTeK P7131 Dual 1043:4862 [12465.029087] saa7134: card=79 -> Sedna/MuchTV PC TV Cardbus TV/Radio (ITO [12465.029094] saa7134: card=80 -> ASUS Digimatrix TV 1043:0210 [12465.029102] saa7134: card=81 -> Philips Tiger reference design 1131:2018 [12465.029110] saa7134: card=82 -> MSI TV@Anywhere plus 1462:6231 1462:8624 [12465.029120] saa7134: card=83 -> Terratec Cinergy 250 PCI TV 153b:1160 [12465.029128] saa7134: card=84 -> LifeView FlyDVB Trio 5168:0319 [12465.029137] saa7134: card=85 -> AverTV DVB-T 777 1461:2c05 1461:2c05 [12465.029147] saa7134: card=86 -> LifeView FlyDVB-T / Genius VideoWonder D 5168:0301 1489:0301 [12465.029156] saa7134: card=87 -> ADS Instant TV Duo Cardbus PTV331 0331:1421 [12465.029165] saa7134: card=88 -> Tevion/KWorld DVB-T 220RF 17de:7201 [12465.029173] saa7134: card=89 -> ELSA EX-VISION 700TV 1048:226c [12465.029182] saa7134: card=90 -> Kworld ATSC110/115 17de:7350 17de:7352 [12465.029191] saa7134: card=91 -> AVerMedia A169 B 1461:7360 [12465.029200] saa7134: card=92 -> AVerMedia A169 B1 1461:6360 [12465.029208] saa7134: card=93 -> Medion 7134 Bridge #2 16be:0005 [12465.029216] saa7134: card=94 -> LifeView FlyDVB-T Hybrid Cardbus/MSI TV 5168:3306 5168:3502 5168:3307 4e42:3502 [12465.029229] saa7134: card=95 -> LifeView FlyVIDEO3000 (NTSC) 5169:0138 [12465.029238] saa7134: card=96 -> Medion Md8800 Quadro 16be:0007 16be:0008 16be:000d [12465.029249] saa7134: card=97 -> LifeView FlyDVB-S /Acorp TV134DS 5168:0300 4e42:0300 [12465.029259] saa7134: card=98 -> Proteus Pro 2309 0919:2003 [12465.029267] saa7134: card=99 -> AVerMedia TV Hybrid A16AR 1461:2c00 [12465.029276] saa7134: card=100 -> Asus Europa2 OEM 1043:4860 [12465.029284] saa7134: card=101 -> Pinnacle PCTV 310i 11bd:002f [12465.029293] saa7134: card=102 -> Avermedia AVerTV Studio 507 1461:9715 [12465.029301] saa7134: card=103 -> Compro Videomate DVB-T200A [12465.029308] saa7134: card=104 -> Hauppauge WinTV-HVR1110 DVB-T/Hybrid 0070:6700 0070:6701 0070:6702 0070:6703 0070:6704 0070:6705 [12465.029324] saa7134: card=105 -> Terratec Cinergy HT PCMCIA 153b:1172 [12465.029332] saa7134: card=106 -> Encore ENLTV 1131:2342 1131:2341 3016:2344 [12465.029344] saa7134: card=107 -> Encore ENLTV-FM 1131:230f [12465.029352] saa7134: card=108 -> Terratec Cinergy HT PCI 153b:1175 [12465.029360] saa7134: card=109 -> Philips Tiger - S Reference design [12465.029367] saa7134: card=110 -> Avermedia M102 1461:f31e [12465.029375] saa7134: card=111 -> ASUS P7131 4871 1043:4871 [12465.029384] saa7134: card=112 -> ASUSTeK P7131 Hybrid 1043:4876 [12465.029392] saa7134: card=113 -> Elitegroup ECS TVP3XP FM1246 Tuner Card 1019:4cb6 [12465.029401] saa7134: card=114 -> KWorld DVB-T 210 17de:7250 [12465.029409] saa7134: card=115 -> Sabrent PCMCIA TV-PCB05 0919:2003 [12465.029418] saa7134: card=116 -> 10MOONS TM300 TV Card 1131:2304 [12465.029426] saa7134: card=117 -> Avermedia Super 007 1461:f01d [12465.029435] saa7134: card=118 -> Beholder BeholdTV 401 0000:4016 [12465.029443] saa7134: card=119 -> Beholder BeholdTV 403 0000:4036 [12465.029451] saa7134: card=120 -> Beholder BeholdTV 403 FM 0000:4037 [12465.029459] saa7134: card=121 -> Beholder BeholdTV 405 0000:4050 [12465.029468] saa7134: card=122 -> Beholder BeholdTV 405 FM 0000:4051 [12465.029476] saa7134: card=123 -> Beholder BeholdTV 407 0000:4070 [12465.029484] saa7134: card=124 -> Beholder BeholdTV 407 FM 0000:4071 [12465.029493] saa7134: card=125 -> Beholder BeholdTV 409 0000:4090 [12465.029501] saa7134: card=126 -> Beholder BeholdTV 505 FM 5ace:5050 [12465.029510] saa7134: card=127 -> Beholder BeholdTV 507 FM / BeholdTV 509 5ace:5070 5ace:5090 [12465.029520] saa7134: card=128 -> Beholder BeholdTV Columbus TVFM 0000:5201 [12465.029528] saa7134: card=129 -> Beholder BeholdTV 607 FM 5ace:6070 [12465.029537] saa7134: card=130 -> Beholder BeholdTV M6 5ace:6190 [12465.029545] saa7134: card=131 -> Twinhan Hybrid DTV-DVB 3056 PCI 1822:0022 [12465.029554] saa7134: card=132 -> Genius TVGO AM11MCE [12465.029560] saa7134: card=133 -> NXP Snake DVB-S reference design [12465.029567] saa7134: card=134 -> Medion/Creatix CTX953 Hybrid 16be:0010 [12465.029576] saa7134: card=135 -> MSI TV@nywhere A/D v1.1 1462:8625 [12465.029584] saa7134: card=136 -> AVerMedia Cardbus TV/Radio (E506R) 1461:f436 [12465.029592] saa7134: card=137 -> AVerMedia Hybrid TV/Radio (A16D) 1461:f936 [12465.029601] saa7134: card=138 -> Avermedia M115 1461:a836 [12465.029609] saa7134: card=139 -> Compro VideoMate T750 185b:c900 [12465.029617] saa7134: card=140 -> Avermedia DVB-S Pro A700 1461:a7a1 [12465.029626] saa7134: card=141 -> Avermedia DVB-S Hybrid+FM A700 1461:a7a2 [12465.029634] saa7134: card=142 -> Beholder BeholdTV H6 5ace:6290 [12465.029642] saa7134: card=143 -> Beholder BeholdTV M63 5ace:6191 [12465.029651] saa7134: card=144 -> Beholder BeholdTV M6 Extra 5ace:6193 [12465.029659] saa7134: card=145 -> AVerMedia MiniPCI DVB-T Hybrid M103 1461:f636 1461:f736 [12465.029669] saa7134: card=146 -> ASUSTeK P7131 Analog [12465.029676] saa7134: card=147 -> Asus Tiger 3in1 1043:4878 [12465.029684] saa7134: card=148 -> Encore ENLTV-FM v5.3 1a7f:2008 [12465.029693] saa7134: card=149 -> Avermedia PCI pure analog (M135A) 1461:f11d [12465.029701] saa7134: card=150 -> Zogis Real Angel 220 [12465.029708] saa7134: card=151 -> ADS Tech Instant HDTV 1421:0380 [12465.029716] saa7134: card=152 -> Asus Tiger Rev:1.00 1043:4857 [12465.029725] saa7134: card=153 -> Kworld Plus TV Analog Lite PCI 17de:7128 [12465.029733] saa7134: card=154 -> Avermedia AVerTV GO 007 FM Plus 1461:f31d [12465.029742] saa7134: card=155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid 0070:6706 0070:6708 [12465.029752] saa7134: card=156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid 0070:6707 0070:6709 0070:670a [12465.029763] saa7134: card=157 -> Avermedia AVerTV Studio 507UA 1461:a11b [12465.029772] saa7134: card=158 -> AVerMedia Cardbus TV/Radio (E501R) 1461:b7e9 [12465.029780] saa7134: card=159 -> Beholder BeholdTV 505 RDS 0000:505b [12465.029789] saa7134: card=160 -> Beholder BeholdTV 507 RDS 0000:5071 [12465.029797] saa7134: card=161 -> Beholder BeholdTV 507 RDS 0000:507b [12465.029806] saa7134: card=162 -> Beholder BeholdTV 607 FM 5ace:6071 [12465.029815] saa7134: card=163 -> Beholder BeholdTV 609 FM 5ace:6090 [12465.029823] saa7134: card=164 -> Beholder BeholdTV 609 FM 5ace:6091 [12465.029832] saa7134: card=165 -> Beholder BeholdTV 607 RDS 5ace:6072 [12465.029840] saa7134: card=166 -> Beholder BeholdTV 607 RDS 5ace:6073 [12465.029849] saa7134: card=167 -> Beholder BeholdTV 609 RDS 5ace:6092 [12465.029857] saa7134: card=168 -> Beholder BeholdTV 609 RDS 5ace:6093 [12465.029866] saa7134: card=169 -> Compro VideoMate S350/S300 185b:c900 [12465.029874] saa7134: card=170 -> AverMedia AverTV Studio 505 1461:a115 [12465.029883] saa7134: card=171 -> Beholder BeholdTV X7 5ace:7595 [12465.029892] saa7134: card=172 -> RoverMedia TV Link Pro FM 19d1:0138 [12465.029900] saa7134: card=173 -> Zolid Hybrid TV Tuner PCI 1131:2004 [12465.029909] saa7134: card=174 -> Asus Europa Hybrid OEM 1043:4847 [12465.029917] saa7134: card=175 -> Leadtek Winfast DTV1000S 107d:6655 [12465.029926] saa7134: card=176 -> Beholder BeholdTV 505 RDS 0000:5051 [12465.029934] saa7134: card=177 -> Hawell HW-404M7 [12465.029941] saa7134: card=178 -> Beholder BeholdTV H7 [12465.029948] saa7134: card=179 -> Beholder BeholdTV A7 [12465.029955] saa7134: card=180 -> Avermedia PCI M733A 1461:4155 1461:4255 [12465.029967] saa7130[0]: subsystem: 1131:0000, board: UNKNOWN/GENERIC [card=0,autodetected] [12465.030033] saa7130[0]: can't get MMIO memory @ 0x0 [12465.030051] saa7134: probe of 0000:01:07.0 failed with error -16 [12465.053892] saa7134 ALSA driver for DMA sound loaded [12465.053900] saa7134 ALSA: no saa7134 cards found tvtime-scanner Leyendo la configuración de /etc/tvtime/tvtime.xml Leyendo la configuración de /home/ricardo/.tvtime/tvtime.xml Escaneando usando la norma de TV NTSC. /home/ricardo/.tvtime/stationlist.xml: No existing NTSC station list "Custom". videoinput: Cannot open capture device /dev/video0: No existe el dispositivo o la dirección ls /dev/ No video directory here

  Read the article

< Previous Page | 70 71 72 73 74 75 76  | Next Page >